Processeurs et cartes mères supportéesWilkoBulteMaintenu par Des retours, mises à jour et corrections a
cette liste sont encouragés.AperçuCe document se veut être un point de départ pour tous
ceux qui désirent faire fonctionner &os; sur des machine à
base de processeurs Alpha. Ce guide fournit des informations sur
les différentes architectures matérielles. Il ne se veut pas
un remplaçant aux pages de manuel du système.L'information est structuré de la manière
suivante:Généralité sur le matériel
Alpha pour fonctionner avec &os;;Information spécifique au système pour chacune
des cartes mères supportées par &os;;Informations sur les cartes d'extension sous &os;,
incluant les différences entre ces cartes et la liste de
matériel générique supportée.Vous trouverez des références à DEC, Digital
Equipment Corporation et Compaq, utilisé de façon
interchangeable dans ce document. Compaq ayant racheté
Digital Equipment, il serait plus correcte de se
référé à Compaq uniquement. Je vous
prie d'accepter mes excuses sur la mixité de ces noms
trouvées dans ce document.Les commandes SRM seront indiquées en
MAJUSCULE. L'utilisation des minuscules
en entrée est acceptée par SRM. Les majuscules sont
utilisées par soucis de clarté.Compaq a mis en ligne des informations pour les
développeurs Linux, qui sont très utiles aussi pour les
utilisateurs de &os;. Voyez la page des Utilitaires
Linux pour Alpha.De quoi avez vous besoin pour faire fonctionner &os; sur
une plateforme Alpha?Bien sur, vous devez disposer d'une machine Alpha reconnue
par &os;. Les machines Alpha ne sont PAS comme des PCs. Il existe
un nombre considérable de différences entre les
différents composants de base et les architectures de cartes
mères. Cela veut dire que le noyau doit connaîtres les
détails les plus fins de la machine sur laquelle il doit
fonctionner. Cela veut dire que un noyau
GENERIC risque, la plupart du temps de ne pas
fonctionner.Pour une machine sur laquelle vous désirez faire
fonctionner &os;, assurez vous que le microcode de la console SRM
est installé. Ou assurez vous que le microcode de console SRM
est disponible pour ce type de machine. Si &os; ne supporte pas
encore votre type de machine, il y a beaucoup de chance pour que
cela change dans l'avenir, si le SRM est disponible. Toutes ces
assomptions sont fausses si le microcode de console SRM n'est pas
disponible.Les machines disposant d'un microcode de console ARC ou
AlphaBIOS ont été prévues pour fonctionner avec
WindowsNT. Certaines disposent d'un microcode de console SRM dans
la ROM système, il suffit de le selectionner (via le menu ARC
ou AlphaBIOS correspondant). Dans tous les autres cas vous devrez
ré-inscrire le code SRM dans les ROMs. Vérifiez sur
le site des
microcode Alpha pour vérifier si il est disponible pour
votre système. Dans tous les cas: no SRM veut
dir qu'il n'existe pas pour &os; (ou NetBSD, OpenBSD, Tru64 Unix
ou OpenVMS). Avec la déconvenue de WindowNT/alpha, un grand
nombre de machines NT de seconde main sont vendues. Elles ont
très peu ou aucune valeur de revente si elles ne disposent que
du microcode de console NT. Soyez donc attentif si le prix parait
trop bon.Les machines non-SRM connues sont:les séries Digital XLles séries Digital XLTSamsung PC164UX (Ruffian)Samsung 164BLes machines disposant de code SRM, mais non supportées
par &os; sont: DECpc 150 (Jensen)DEC 2000/300 (Jensen)DEC 2000/500 (Culzean)AXPvme series (Medulla)Pour compliquer le tout: Digital a appelé
white-box, des machines Alpha destinées
uniquement à WindowsNT et blue-box des machines
Alpha destinées uniquement à OpenVMS et Digital Unix. Ces
noms correspondent à la couleur du coffret, respectivement
FrostWhite et TopGunBlue. Même si
vous réussisez à mettre un microcode de console SRM sur une
whitebox, OpenVMS et Digital Unix refuserons de
démarrer. &os; dans la version post 4.0-RELEASE fonctionnera
sur ces variantes. Avant tout; les machines white
sont différentes des autres (lisez: moins cher) machines
Digital.Vous obtiendrez le code PAL OSF/1 (OSF/1 est le nom initial
de Digital Unix sur les plateformes Alpha) comme partie du code
SRM. Le code PAL peut être vu comme une couche d'abstraction
logicielle entre le matériel et le système
d'exploitation. Il utilise des instructions processeurs standards
et réservées à PAL. PAL n'est pas un microcode. Le
micro-noyau de console ARC contient une version différente du
code PAL, développé pour WindowsNT et qui n'est pas
utilisable par &os; (de façon plus générale: Unix ou
OpenVMS). Linux/alpha fournit une version spécifique du code
PAL, permettant de fonctionner sur les machines ARC et
AlphaBIOS. Il y a plusieurs raisons pour lesquelles cela n'est pas
une bonne idées pour les développeurs des *BSD. Nous ne
rentrerons pas dans les détails ici. Si vous etes
intereéssé par les détails, cherchez les sur
les site web de &os; et NetBSD.Un autre détail est important: vous devez disposer d'un
adaptateur de disque reconnu par le code de console SRM, si vous
voulez démarrer depuis un disque. Pour les machines anciennes
basées sur du PCI, cela veut dire que vous devez disposer d'une
adaptateur basé sur un NCR/Symbios 53C810 ou Qlogic
1020/1040. Certaines machines disposent d'un composant SCSI sur la
carte mère. Les machines et version de SRM plus récentes
sont capables de fonctionner avec des composants/adaptateurs SCSI
plus modernes. Vérifiez les informations spécifiques
à la machine utilisé ci-dessous. Notez que la suite
de ce document refère aux machines disposant d'un composant
Symbios, cela correspond aussi aux plus vieux composants
noté NCR. Symbios ayant racheté Symbios.Les principaux problèmes se posent pour les personnes
ayant des machines qui ont commencé leur vie avec
WindowsNT. ARC et AlphaBIOS détectent
d'autres adaptateurs que ceux sur lesquels
SRM est capable de démarrer. Par exemple, vous pouvez
démarré sur une carte Adaptec 2940UW avec ARC/AlphaBios,
mais (générallement) pas avec SRM. Certaines nouvelles
machines ont introduit le support Adaptec pour le
démarrage. Consultez la section spécifique de votre machine
pour plus de détails.La plupart des adaptateurs qui ne permettent pas de
démarrer fonctionnent parfaitement pour une utilisation en
disque de données. Les différences entre SRM et ARC peuvent
également apparaitre dans les systèmes (principalement
Windows NT) disposant de disques dur et de CDROM IDE
intégrés. Des versions de SRM permettant de
démarrer sur des disques IDE ou des CDROM existent (cela
dépend du type de machine). Consultez la section
spécifique à votre machine pour plus de
détails.&os; 4.0 et supérieur peut être démarrer
depuis le CDROM de distribution. Les version
précédentes doivent démarrer depuis une
version 2 disquettes.Dans le but d'être démarrable, la partition root
(partition a) doit se situer au début du disque (offset
0). Cela veut dire que vous devez utiliser l'installeur dans le
menu partition et assigner la partition a avec un
offset de 0 à la partition de base. La suite du partitionnement
peut se faire comme vous le désirer. Si vous ne respecter pas
cette règle, le reste de l'installation de passera bien, mais
le système refusera de démarrer sur ce disque.Si vous ne disposez pas de disque local, vous pouvez
démarrer via le réseau Ethernet. Cela nécessite un
adaptateur Ethernet reconnu par la console SRM. Généralement
Générallement il vous faut dispose d'une interface
basé sur une interface 21040 ou 21142 ou 21143. Les
anciennes machines ou version de SRM ne reconnaissent pas les
composants 21142/21143 Fast Ethernet, vous etes donc
limités à 10Mb pour un démarrage par le
réseau de ces machines. Les cartes non fabriquées
par DEC basées sur ces composants vont
générallement(mais cela n'est pas garanti)
fonctionner correctement. Notez que Intel à continué
les puces 21x4x lorsqu'ils ont racheté Digital
Semiconductor. Vous risquez donc de voir un logo Intel sur elle un
de ces jours. Les machines récentes disposent d'un support
SRM pour les puces Ethernet Intel 8255x.Les machines Alpha peuvent fonctionner avec SRM sur une
console graphique ou une console série. ARC peut aussi
fonctionner sur des consoles séries. L'émulation VT100 avec
8 bits de controle doit vous permettre de passer du mode
ARC/AlphaBIOS au mode SRM sans avoir à installer une carte
graphique.Si vous désirez utiliser une machine Alpha sans moniteur
ou carte graphique, ne connectez pas de clavier ou de souris
dessus. Branchez plutot un terminal série[emulateur] sur le
port série numéro 1. SRM disloguera alors en 9600N81. Cela
est très pratique pour débogguer. Attention: certains/la
plupart (?) des codes SRMs vous présenteront un prompt console
sur le port série numéro 2. Le noyau de
démarrage quand a lui, affichera les message de
démarrage sur le port série numéro 1 et
activera la console sur ce port aussi. Cela peut porter
à confusion.La plupart des machines Alpha disposant d'un bus PCI,
peuvent utiliser des cartes VGA de type PC. Le code SRM est
suffisant pour les faire fonctionner. Cela ne veut pas dire que
toutes les cartes CGA PCI du marché fonctionneront sur des
machines Alpha. Les cartes de type S3 Trio64, Mach64, et Matrox
Millennium fonctionnent. Les vieilles cartes ISA basées sur
ET4000 fonctionnent aussi pour moi. Mais poser la question autour
de vous avant d'en acheter une.La plupart des périphériques PCI du monde PC
fonctionnent avec des machines &os; basées sur du
PCI. Vérifiez le dernier fichier
/sys/alpha/conf/GENERIC pour plus
d'informations. Vérifiez la partie sur la machine appropriée
dans le cas ou vous désirez utilisez des cartes PCI qui
disposent de ponts PCI. Dans certains cas vous risquez d'obtenir
des problèmes avec les cartes PCI qui ne gèrent pas
correctement la parité PCI. Cela peut conduire a des panics du
système. Le controle de parité PCI peut être
désactivé en utilisant la commande SRM suivante:>>>SET PCI_PARITY OFFCela n'est pas un problème &os;, tous les systèmes
d'exploitation fonctionnant sur du matériel Alpha nécessite
ce contournement.Si votre système contient (aussi) des slots d'extension
EISA vous devez executer l'utilitaire de configuration EISA(ECU)
après l'installation des cartes EISA ou après la
mise à jour du micro-noyau de la console.Il y a plusieurs générations de processeurs Alpha. La
processeur original est le 21064. Il a aussi été
produit sous le nom de MOS4, les puces fabriqué sous ce nom
sont aussi connues sous le nom de EV4. Les nouveaux processeurs
sont 21164, 21264, etc... Vous trouverez les désignations
suivantes EV4S, EV45, EV5, EV56, EV6, EV67, EV68. Les EVs
disposant de 2 numéros sont des versions
améliorées. Par example EV45 est une version
améliorée au niveau des nombre flottants et dispose
d'une puce de 16 kByteséparée pour le cache I &
D, comparé à la version EV4 sur laquelle il est
basé. Plus grand est le nombre suivant immédiatement
EV, plus il est interessant (lisez: rapide/plus
moderne).Au niveau mémoire, vous devez disposer d'au moins
32Mbytes. J'ai réussi à faire fonctionner &os; sur un
système disposant de 16Mbyte, mais cela n'est pas très
amusant. Le temps de compilation a été divisé par 2
lorsque j'ai disposer de 32 Mbytes. Notez que la console SRM
nécessite 2Mbyte de mémoire. Pour fonctionner correctement
64 Mbytes de mémoire est le minimum recommandé.Pendant que nous sommes dans le sujet de la mémoire,
faites attention au type de mémoire utilisé par votre
machine. Il y a énormément de configurations
mémoire pour chaque machine.Pour finir: j'espère que les informations ci-dessus
seront suffisantes pour un utilisateur novice
d'Alpha. N'hésitez pas à poser des questions sir quelque
chose n'est pas clair après la lecture de ce document.Informations spécifiques aux systèmesCi-dessous, vous trouverez un aperçu du matériel sur
lequel fonctionner &os;. Cette liste est amenèe à grossir,
un coup d'oeil à /sys/alpha/conf/GENERIC
vous éclairera.Les machines Alpha sont le plus souvent connu sous leur nom
de code. Lorsqu'il est connu, celui-ci est listé ci-dessous
entre parenthèses.AXPpci33 (NoName)Le NoName est une carte mère à base de
bébé-AT, baséee sur le processeur 21066 LCA
(Low Cost Alpha). La puce LCA inclue toute la logique pour
gérer un bus PCI et le sous-système
mémoire. Toute ceci conçut à un faible
prix.Du à la limitation de l'interface mémoire, le
système n'est pas particulièrement répide
dans le cas ou il ne dispose pas de cache.Comme vous pourrez
vous en apercevoir, ce processeur est comparable à un
21064 (première génération de processeur
Alpha). Ces cartes mères peuvent être trouvé
à un prix très bas maintenant. Il correspond
à un véritable CPU 64 bit, donc ne vous attendez
pas à des miracles tant que la vitesse n'augmente
pas.Fonctionnalités:Processeurs Alpha 21066 à 166 MHz ou 21066A
CPU à 233MHz. Les processeurs 21068 sont aussi
disponibles mais sont plus lents.Bcache embarqué / cache de niveau 2: 0, 256k
ou 1 Mbyte (utilisation des puces DIL)Souris PS/2 & port clavier OU clavier 5 broches DIN
(2 modèles de carte mère)Mémoire:Longueur du bus: 64 bitsStyle PS/2, 72 pin 36 bit Fast Page Mode SIMMs70ns ou inférieurinstallé par paire4 emplacements SIMMutilisation ECC512kB de Flash ROM Flash pour le code de console.2 ports séries 16550A1 port parallèleinterface pour disquette1 interface IDE embarquéeExtensions:3 emplacements 32 bit PCI (1 est partagé avec
de l'ISA)5 emplacements ISA (1 est partagé avec le
PCI)Fast SCSI intégré grace à l'utilisation
d'une puce Symbios 53C810Les cartes NoName peuvent disposer d'un micro-noyau de
console SRM ou ARC dans la ROM flash. La
ROM flash ne permet par de contenir les deux version en même
temps et de choisir par logiciel quelle code utiliser. Mais vous
n'avez besoin que du code SRM de toute façon.Le cache sur les cartes NoNames est une puce à 15 ou 20
ns. Avec un cache de 256kBytes vous aurez l'impression d'avoir
une carte mère de 486. Les puces de de cache de 1Mbyte sont
très rare. Un minimum de 256kBytes de cache est recommandé
pour une performance acceptable. Avec moins de cache le
système est vraiment trop lent.La carte mère NoName dispose d'un connecteur standard
d'alimentation PC/AT. Elle dispose aussi d'une connecteur
d'alimentation 3.3 Volts. Il n'y a pas besoin de se fatiguer
à trouver une nouvelle source d'alimentation. Le 3.3 Volts
est nécessaire uniquement dans le cas ou vous utilisez des
cartes d'extension PCI 3.3 Volts. Elles sont très rare.L'interface IDE est supportée par &os; et nécessite
la ligne suivante dans le fichier de configuration du noyau:device ataL'interface ATA interface utilise l'irq 14.La console SRM ne permet néanmoins pas de
démarrer depuis des disques IDE. Cela veut dire que
vous devez utiliser un disque SCSI pour périphérique de
démarrage.Les cartes NoName semblent têtues lorsqu'elles
utilisent des consoles séries. Elles nécessitent>>> SET CONSOLE SERIALavant de fonctionner. Le simple faire de mettre le clavier
sur la machine ne suffit pas, comme sur la plupart des autres
modèles d'Alpha. Le retour à une console graphique
nécessite >>> SET CONSOLE GRAPHICSsur la console série.Il y a eut différents retour sur le fait que vous devez
presser les touches
Control-Alt-Del
pour capter l'attention de la console SRM. Je ne l'ai jamais
noté moi-même, mais si sachez le, si vous obtenez un
écran blanc après le démarrage.Vérifiez que vous utilisé de vrais barrette
SIMMs 36 bit et uniquement des DRAM FPM (Fast Page Mode). Les
DRAM EDO ou les barrettes SIMM avec de fausse parité
ne fonctionne pas . La carte utilise les 4
bits supplémentaires pour l'ECC. Les barrettes SIMM FPM
33 bits ne fonctionneront pas pour les mêmes
raisons.Si vous avez le choix, prenez la variante de carte mère
de style PS/2. En plus de vous donner un port supplémentaire
pour la souris, elle est directement supportée par Tru64
Unix, dans le cas ou vous voudriez le faire fonctionner. La
variante avec un connecteur DIN doit fonctionner
correctement avec &os;.La lecture du
manuel OEM est recommandé.Le fichier de configuration du noyau pour un noyau NoName
doit contenir la ligne:options DEC_AXPPCI_33 cpu EV4Universal Desktop Box (UDB ou Multia)Multia supporte les processeurs Intel ou Alpha. Nous
assumerons que nous utilisons un Alpha.Multia est destiné à être une sorte de
station de travail personnelle. Il existe
énormément de version, vérifiez donc bien
ce que vous avez.Fonctionnalités:processeur Alpha 21066 à 166 MHz ou 21066A
à 233MHzBcache embarqué / cache de niveau 2: module de
cache 256 kByte de type COAST; les modèles à 233MHz
disposent de 512kByte de cache; les modèles à 166MHz
sont vendus avec 256kB de cacheport souris PS/2 & claviermémoire:longueur du bus: 64 bitsbarrettes SIMM de type PS/2 72 pin 36 bit Fast
Page Mode70ns ou inférieurles barrette SIMMs sont à
installées par paire4 emplacements de barrette SIMMutilisation de ECC2 ports série 16550A1 port parallèle1 interface de lecteur de disquette1 pont Intel 82378ZB PCI vers ISA1 carte 10Mb Ethernet (basé sur une puce 21040),
avec un connecteur AUI ou 10base2Extension:1 emplacement 32 bit PCI2 emplacements PCMCIAcarte son Crystal CS4231 ou AD1848
intégréeFast SCSI intégré, grace à l'utilisation
d'une puce Symbios 53C810[A] sur une carte PCIMultia dispose d'assez de mémoire ROM flash pour
enregistrer les codes SRM et ARC en même temps et permettre
la sélection logicielle de l'un ou l'autre.L'adaptateur vidéo TGA intégré, n'est
pas pour l'instant utilisable comme console
sous &os;. Vous devrez utiliser une console série.Multia ne dispose que d'un emplacement d'extension PCI 32
bits, et il n'est utilisable que pour une faible portion de
cartes PCI. En sacrifiant cet emplacement PCI, vous pourrez
ajouter une disque dur de 3.5". Il se peut que cet ajout
soit inclu avec votre Multia. Ajouter un disque de 3.5"
supplémentaire n'est pas recommendé
du à la limitation de l'alimentation et du fabile
refroidissement de ce modèle.Multia dispose aussi de deux emplacement d'extension
PCMCIA. Il ne sont pas actuellement supportés par &os;.Le processeur peut ou peut ne pas être
soudé. Vérifier cela avec d'envisager une mise
à jour du processeur. Les modèles de base de
Multia ont un processeur soudé sur la carte
mère.Multia dispose de 2 ports séries, mais un seul
connecteur externe 25 pin sub-D. Le FAQ des Multia explique
comment créer votre propre cable Y pour utiliser les deux
ports.Bien que le SRM Multia supporte le démarrage depuis un
lecteur de disquette, cela peut poser des
problèmes. Typiquement les messages d'erreurs sont:*** Soft Error - Error #10 - FDC: Data overrun or underrunCela n'est pas une problème de &os;, c'est un
problème SRM. La meilleur façon d'installer &os; est de le
faire depuis un CDROM SCSI..Il y a eut différents retour sur le fait que vous devez
presser les touches
Control-Alt-Del
pour capter l'attention de la console SRM. Je ne l'ai jamais
noté moi-même, mais si sachez le, si vous obtenez un
écran blanc après le démarrage.La carte son fonctionne correctement via le gestionnaire
de périphérique &man.pcm.4; et une ligne dans le fichier
de configuration du noyau pour la puce Crystal CS4231:device pcmLe périphérique sonore réside au port
0x530, et utilise l'irq 9 avec le drq 3. Vous devez de plus
spécifier le drapeau 0x15 dans le fichier
device.hints.Je n'ai pas réussi à faire fonctionner correctement
le son avec un Multia et une puce AD1848.En vérifiant à l'écoute, je me suis
souvenu de la faible alimentation du processeur
166MHz. L'écoute des MP3 est acceptable si vous utilisez
un taux de 22kHz.Les Multia sont connues pour arrèter de fonctionner du
a des problèmes de chaleur. L'etroitesse de la boite ne
permet vraiment pas d'obtenir une bonne ventilation. Positionnez
donc votre Multia à la verticale, ne la mettez pas à
l'horizontale (style pizza). Remplacer le
ventilateur par un rafraichissant plus est vraiment
recommandé. Vous pouvez aussi couper un des fils du senseur
de vitesse du ventilateur. Une fois couper, le ventilateur
tournera à une vitesse (et un bruit) plus rapide. Faites
attention aux cartes PCI avec une forte consommation
d'énergie. Si votre système Multia cesse de fonctionner
suite à un problème de chaleur, consultez les pages du
site web de NetBSD
pour de l'aide sur la façon de le remettre en marche.Le pont Intel 82378ZB PCI vers ISA permet d'utiliser un
disque IDE. Cela nécessite la ligne de configuration du noyau
suivante:device ataL'interface ATA utilise l'IRQ 14.Les espacements des connecteurs IDE sont espacés pour
des disques de portable de 2.5". Un disque IDE de 3.5"
de pourra donc pas être utilisé. Néanmoins sans
sacrifier un emplacement PCI vous disposer d'un disque IDE. La
console SRM ne permet pas malgré tout de démarrer depuis
un disque IDE. vous devez disposer d'un disque SCSI comme disque
de démarrage.Dans le cas ou vous désirez changer le disque dur
interne: le cable interne reliant la carte PCI au disque dur
2.5" à une taille plus petite que
les cables SCSI standards. Sinon il ne pourrait aller avec les
disque de 2.5". Il existe des cartes PCI disposant d'un
cable standard, permettant de brancher un disque dur SCSI
standard.Encore une fois, je ne recommande pas d'essayer de
remplacer le disque dur interne. Utilisez le connecteur SCSI
externe et mettez le disque dur dans un boitier externe. Les
Multia sont suffisement chaud sans cela. Dans la plupart des cas
vous disposerez du connecteur 50 broches SCSI, mais certains
modèles de Multia peuvent ne pas comporter de disque ni de
connecteur. Encore un point à véirifer avec l'achat.Le fichier de configuration du noyau doit contenir la
ligne suivante pour un système Multia:options DEC_AXPPCI_33 cpu EV4La lecture du document
http://www.netbsd.org/Ports/alpha/multiafaq.html ou
http://www.brouhaha.com/~eric/computers/udb.html est
recommandé.Station de travail personnelle (Miata)La Miata est une machine de type tour conçues pour
fonctionner sur un bureau. Il existe plusieurs type de
Miata. L'original de Miata est le modèle MX5. Du au
différents problèmes de conception matérielle, une
nouvelle conception a été faite, donnant le modèle
MiataGL. Quoiqu'il en soit les variantes ne sont pas facilement
distinguables à première vue en regardant le boitier. La
façon la plus simple est de chercher à l'arrière des
machines si il y a deux connecteurs USB. Si oui, c'est un
MiataGL. Les modèles MX5 semblent être les plus
utilisés sur le marché.La désignation système resemble à
Personal Workstation 433a. Personal Workstation
est souvent réduit à PWS. Cela veut dire qu'il
dispose d'un processeur 433 MHz et que sa vie à commencer
sous une station de travail WinNT (le a de la
fin). Les systèmes prévus pour fonctionner sous
Tru64 Unix ou OpenVMS afficheront 433au. Les
systèmes Miatas-WinNT sont souvent
préconfigurées avec un lecteur de CDROM IDE. En
général ces systèmes sont
désigné comme PWS[433,500,600]a[u].Il existe un modèle de Miata avec un système de
refroidissement de processeur spécifique de Kryotech. Le
Kryotech à un refroidissement spécial et est enfermé
dans une boite différente..Fonctionnalités:processeurs Alpha 21164A EV56 à 433, 500 ou
600MHzjeux de puce 21174 Core Logic (Pyxis)Bcache / cache de niveau 3: 0, 2 ou 4 Mbytes (utilis
un module de cache)Mémoire:longeur du bus: 128 bits wide, protection par ECCbarrette DIMMS 72 bit wide SDRAMs,
installées par paire6 emplacement pour les barrette DIMMun maximum de 1.5 GBytes de mémoire Fast Ethernet intégré:le MX5 utilise une puce Ethernet 21142 ou 21143,
suivant la version de la carte PCI utiliséle MiataGL dispose d'une puce 21143le connecteur peut être 10/100 Mbit UTP, ou
10 Mbit UTP/BNC2 interfaces de disque dur [E]IDE intégrés,
basées sur CMD646 (MX5) ou Cypress 82C693 (MiataGL)1 controleur Ultra-Wide SCSI Qlogic 1040 [MiataGL
uniquement]2 emplacements PCI 64-bit3 emplacements PCU 32-bit (derrière un pont
PCI-PCI DEC)3 emplacements ISA (physiquement partagés avec
les emplacements PCI 32 bits via un pont Intel 82378IB PCI
vers ISA)2 ports séries 16550A1 port parallèleport PS/2 clavier & sourisinterface USB [MiataGL uniquement]carte son intégrée, basée sur
une puce ESS1888La logique des Miata est divisé en deux cartes de
circuits imprimées. La carte inférieure dispose des
emplacements PCI et ISA ainsi que des choses comme la carte son,
etc... La carte supérieure comporte le processeur, la puce
Pyxis, la mémoire, etc.. Notez que le modèle MX5
diffère du modèle MiataGL par la carte de canal du bus
PCI. Cela veut dire que vous ne pouvez mettre à jour votre
carte vers un modèle MiataGL (avec la nouvelle puce Pyxis),
cela nécessite une carte de canal PCI
différente. Apparemment une carte processeur MiataGL avec un
canal PCI de MX5 fonctionne, mais cela n'est définitivement
pas supporté ni testeé. Tout le reste (boitier, cablage,
etc...) est identique entre le MX5 et le MiataGL.Les MX5 ont des problèmes avec les emplacements PCI
64-bit et le DMA, lorsque le DMA dépasse un espace de
pagination. Les emplacements 32 bits n'ont pas ce problèmes
car le pont PCI-PCI ne permet pas ce type de transfert. Le code
SRM reconnait le problème et refuse de démarrer un
système si une carte PCI 64 bit est présente et qu'il ne
la connait pas. Les bonnescartes 64 bits pour SRM
peuvent utiliser les emplacements 64 bits.Si vous désirez ne pas tenir compte de SRM, vous pouvez
taper set pci_device_override à
l'invite de commande SRM. Ne vous étonnez pas si vos
données disparaissent mistériseusement.La commande exacte est:>>>SET PCI_DEVICE_OVERRIDE <vendor_id><device_id>Par exemple:>>>SET PCI_DEVICE_OVERRIDE 88c15333Une approche plus radicale est d'utiliser:>>>SET PCI_DEVICE_OVERRIDE -1Cela désactive la vérification de l'ID PCI, cela
vous permet d'installer n'importe quelle carte PCI sans que son
ID soit vérifier. Pour que cela fonctionne vous devez avoir
une version raisonnablement récente de SRM.Si vous faites cela, c'est à vos propres
risques...Le noyau &os; rapporte lorsqu'il voit des puces Pyxis
bogguées:Sep 16 18:39:43 miata /kernel: cia0: Pyxis, pass 1
Sep 16 18:39:43 miata /kernel: cia0: extended capabilities: 1<BWEN>
Sep 16 18:39:43 miata /kernel: cia0: WARNING: Pyxis pass 1 DMA bug; no bets...Un test sur MiataGL donne :Jan 3 12:22:32 miata /kernel: cia0: Pyxis, pass 1
Jan 3 12:22:32 miata /kernel: cia0: extended capabilities: 1<BWEN>
Jan 3 12:22:32 miata /kernel: pcib0: <2117x PCI host bus adapter> on cia0Le MiataGL n'a pas le problème de DMA du MX5. Les
cartes PCI qui posent problème au SRM du MX5 sont
acceptées sans problème dans les emplacements 64 bits de
MiataGL.La dernière révision de la carte mère des MX5,
contient un contournement matériel pour ce bogue. SRM ne
connait rien de ceci et réagit comme avant avec les cartes
inconnues. Comme le fait aussi le noyau &os;.Le SRM Miata permet de démarrer depuis les lecteurs de
CDROM IDE. Les démarrages sur disques IDE fonctionnent pour
les disques MiataGL et MX5, vous pouvez donc mettre la partition
principale de &os; sur un disque IDE. La vittesse de transfert
est de l'ordre de 14 Mbytes/sec sur un système MX5. La puce
CMD646 du Miata permet de supporter jusque'au mode WDMA2 car
cette puce est trop bogguée pour utiliser le UDMA.Les Miata MX5 utilisent généralement des adaptateurs
SCSI basés sur des Qlogic 1040. Ils permettent de démarrer
le noyau depuis la console SRM. Notez que les cartes Adaptec
ne permettent pas de démarrer depuis la
console SRM Miata.Le MiataGL dispose d'un pont PCI-PCI plus rapide que celui
des MX5. Certains canaux des MX5 disposent de la
même puce que le MiataGL. De toute
façon il existe énormément de variantes.Toutes les cartes VGA ne fonctionnent pas dérrière
le pont PCI-PCI. Cela se manifeste par aucun affichage
vidéo. La solution consiste à mettre la carte VGA dans un
emplacement 64 bits PCI avant le pont.Les MX5 et MiataGL disposent d'une puce sonore, un
ESS1888. C'est une émulation SoundBlaster qui peut être
activer en mettant la lignedevice pcm device sbcdans le fichier de configuration du noyau.Dans le cas ou votre Miata dispose d'une carte de cache
optionnelle, cérifiez qu'elle est bien enfoncée. Des
pertes de cache ont été observées causant des
crashes(cela n'est pas surprenant, mais assez embêtant lors
de débogguage). Le module de cache est identique sur les MX5
ou les MiataGL.L'installation d'un cache de 2mb, mis à part le gain de
10-15% de vitesse (basé sur la temps de compilation de
buildworld), baisse la bande passante pour la lecture PCI DMA
des cartes PCI 64 bits. Un test sur une carte 64-bit Myrinet
résulte d'une baisse de 149 Mbytes/sec à 115
Mbytes/sec. Ceci est un point important à garder dans le cas
ou vous devez effectuer des transferts très rapide avec les
adaptateurs PCI 64 bits.Le changement vers un processeur plus rapide est très
simple; remplacez le processeur et modifiez les dipswitch de
multiplieur de l'horloge à la vitesse du nouveau
processeur.Si vous obtenez des erreurs SRM commeERROR: scancode 0xa3 not supported on PCXALaprès avoir arréter &os;, vous devez mettre à
jour votre micro-code SRM en version V7.2-1 ou supérieure. La
première version SRM disponible peut se trouver sur le CD de
mise à jour du micro-code V5.7, ou sur le site http://www.compaq.com/. Ce
problème SRM a été corrigé sur les
modèles Miata MX5 et Miata GL.L'USB est supporté à partir de &os; 4.1 et
supérieur.Déconnectez le cordon d'alimentation avant de
désassembler la machine, le bouton d'alimentation logicielle,
garde une partie de la carte sous tension
même lorsque la machine est
éteinte.Le fichier de configuration du noyau pour un modèle
Miata doit contenir:options DEC_ST550 cpu EV5Evaluation Board 64 familyIn its attempts to popularize the Alpha CPU DEC produced a number
of so called Evaluation Boards. Members of this family are EB64, EB64+,
AlphaPC64 (codename Cabriolet).
A non-DEC member of this family is the Aspen Alpine.
The EB64 family of evaluation boards has the following
feature set:21064 or 21064A CPU, 150 to 275 MHzmemory:memory buswidth: 128 bitPS/2 style 72 pin 33 bit Fast Page Mode SIMMs70ns or betterinstalled in sets of 48 SIMM socketsuses parity memoryBcache / L2 cache: 0, 512 kByte, 1 Mbyte or 2 Mbytes21072 (APECS) chip setIntel 82378ZB PCI to ISA bridge chip (Saturn)
dual 16550A serial portsparallel printer portSymbios 53C810 Fast-SCSI (not on AlphaPC64)IDE interface (only on AlphaPC64)embedded 10 Mbit Ethernet (not on AlphaPC64)2 PCI slots (4 slots on AlphaPC64)3 ISA slotsAspen Alpine is slightly different, but is close enough to the
EB64+ to run an EB64+ SRM EPROM (mine did..). The Aspen Alpine does
not have an embedded Ethernet, has 3 instead of 2 PCI slots. It comes
with 2 Mbytes of cache already soldered onto the mainboard. It has
jumpers to select the use of 60, 70 or 80ns SIMM speeds.36 bits SIMMs work fine, 3 bits simply remain unused. Note
the systems use Fast Page Mode memory, not EDO memory.The EB64+ SRM console code is housed in an UV-erasable EPROM. No
easy flash SRM upgrades for the EB64+ The latest SRM version available
for EB64+ is quite ancient anyway.The EB64+ SRM can boot both 53C810 and Qlogic1040 SCSI adapters.
Pitfall for the Qlogic is that the firmware that is down-loaded by
the SRM onto the Qlogic chip is very old. There are no updates for the
EB64+ SRM available. So you are stuck with old Qlogic bits too.
I have had quite some problems when I wanted to use Ultra-SCSI drives
on the Alpine with Qlogic. The &os; kernel can be compiled to include
a much newer Qlogic firmware revision. This is not the default because
it adds hundreds of kBytes worth of bloat to the kernel. In &os; 4.1
and later the isp firmware is contained in a kernel loadable module.
All of this might mean that you need to use a non-Qlogic adapter to
boot from.AlphaPC64 boards generally come with ARC console firmware.
SRM console code can be loaded from floppy into the Flash ROM.The IDE interface of the AlphaPC64 is not bootable from the
SRM console.Note that the boards require a power supply that supplies
3.3 Volts for the CPU.For the EB64 family machines the kernel config file must contain:options DEC_EB64PLUS
cpu EV4Evaluation Board 164 (EB164, PC164, PC164LX,
PC164SX) familyEB164 is a newer design evaluation board, based on the 21164A
CPU. This design has been used to spin off multiple variations,
some of which are used by OEM manufacturers/assembly shops. Samsung
did its own PC164LX which has only 32 bit PCI, whereas the Digital
variant has 64 bit PCI.21164A, multiple speed variants [EB164, PC164, PC164LX]21164PC [only on PC164SX]21174 (Alcor) chip setBcache / L3 cache: EB164 uses special cache-SIMMsmemory bus: 128 bit / 256 bitmemory:PS/2 style SIMMs in sets of 4 or 836 bit, Fast Page Mode, uses ECC, [EB164 / PC164]SDRAM DIMMs in sets of 2, uses ECC [PC164SX / PC164LX]
2 16550A serial portsPS/2 style keyboard & mousefloppy controllerparallel port32 bits PCI64 bits PCI [some models]ISA slots via an Intel 82378ZB PCI to ISA bridge chipUsing 8 SIMMs for a 256bit wide memory can yield interesting
speedups over a 4 SIMM/128bit wide memory. Obviously all 8 SIMMs must
be of the same type to make this work. The system must be explicitly
setup to use the 8 SIMM memory arrangement. You must have 8 SIMMs,
4 SIMMs distributed over 2 banks will not work. For the AlphaPC164
you can have a maximum of 1Gbyte of RAM, using 8 128Mbyte
SIMMs. The manual indicates the maximum is 512 Mbyte.The SRM can boot from Qlogic 10xx boards or the Symbios 53C810[A].
Newer Symbios 810 revisions like the Symbios 810AE are not recognized by
the SRM on PC164. PC164 SRM does not appear to recognize a Symbios 53C895
based host adapter (tested with a Tekram DC-390U2W). On the other hand
some no-name Symbios 53C985 board has been reported to work.
Cards like the Tekram DC-390F (Symbios875 based) have been confirmed to
work fine on the PC164. Unfortunately this seems to be dependent on the
actual version of the chip/board.Symbios 53C825[a] will also work as boot adapter. Diamond
FirePort, although based on Symbios chips, is not bootable by the
PC164SX SRM. PC164SX is reported to boot fine with Symbios825,
Symbios875, Symbios895 and Symbios876 based cards. In addition, Adaptec
2940U and 2940UW are reported to work for booting (verified on
SRM V5.7-1). Adaptec 2930U2 and 2940U2[W] do not work.164LX and 164SX with SRM firmware version 5.8 or later can boot
from Adaptec 2940-series adapters.In summary: this family of machines is blessed with a
challenging compatibility as far as SCSI adapters go.On 164SX you can have a maximum of 1 Gbyte of RAM. 4 regular
256MB PC133 ECC DIMMs are reported to work just fine. Whether 512MB
DIMMs will also work is currently unknown.PCI bridge chips are sometimes not appreciated by the 164SX,
they cause SRM errors and kernel panics in those cases. This seems
to depend on the fact if the card is recognised, and therefore
correctly initialised, by the SRM console. The 164SX' onboard
IDE interface is quite slow, a Promise card gives a 3-4 times
speed improvement.On PC164 the SRM sometimes seems to lose its variable settings.
For PC164, current superstition says that, to avoid losing settings,
you want to first downgrade to SRM 4.x and then upgrade to 5.x.
One sample error that was observed was:ERROR: ISA table corrupt!A sequence of a downgrade to SRM4.9, an>>>ISACFG -INITfollowed by>>> INITmade the problem go away. Some PC164 owners report they have never seen
the problem. On PC164SX the AlphaBIOS allows you a selection to select SRM to
be used as console on the next power up. This selection does
not appear to have any effect. In other words, you will get the
AlphaBIOS regardless of what you select. The fix is to reflash the
console ROM with the SRM code for PC164SX. This will overwrite the
AlphaBIOS and will get you the SRM console you desire. The SRM code
can be found on the Compaq Web site.164LX can either have the SRM console code or the AlphaBIOS
code in its flash ROM because the flash ROM is too small to hold
both at the same time.PC164 can boot from IDE disks assuming your SRM version is
recent enough.EB164 needs a power supply that supplies 3.3 Volts. PC164 does
not implement the PS_ON signal that ATX power supplies need to switch on.
A simple switch pulling this signal to ground allows you to run a
standard ATX power supply.For the EB164 class machines the kernel config file must
contain:options DEC_EB164
cpu EV5AlphaStation 200 (Mustang) and 400
(Avanti) seriesThe Digital AlphaStation 200 and 400 series systems are early
low end PCI based workstations. The 200 and 250 series are
desktop boxes, the 400 series is a desk-side mini-tower.Features:21064 or 21064A CPU at speeds of 166 up to 333 MHzDECchip 21071-AA core logic chip-setBcache / L2 cache: 512 Kbytes (200 and 400 series)
or 2048KBytes (250 series)memory:64 bit bus width8 to 384 MBytes of RAM70 ns or better Fast Page DRAMin three pairs (200 and 400 series)in two quads, so banks of four. (250 series)the memory subsystem uses parityPS/2 keyboard and mouse porttwo 16550 serial portsparallel portfloppy disk interface32 bit PCI expansion slots (3 for the AS400-series,
2 for the AS200 & 250-series)ISA expansion slots (4 for the AS400-series,
2 for the AS200 & 250-series)
(some ISA/PCI slots are physically shared)embedded 21040-based Ethernet (200 & 250 series)embedded Symbios 53c810 Fast SCSI-2 chipIntel 82378IB (Saturn) PCI-ISA bridge chipgraphics is embedded TGA or PCI VGA (model dependent)16 bit sound (on 200 & 250 series)The systems use parity memory SIMMs, but these do not need 36 bit
wide SIMMs. 33 bit wide SIMMs are sufficient, 36 bit SIMMs are
acceptable too. EDO or 32 bit SIMMs will not work. 4, 8, 16, 32 and
64 Mbyte SIMMs are supported.The AS200 & AS250 sound hardware is reported to work OK assuming
you have the following line in your kernel config file:device pcmThe sound device uses port 0x530, IRQ 9 and drq 0. You also need
to specify flags 0x10011 in the device.hints file.AlphaStation 200 & 250 series have an automatic SCSI terminator.
This means that as soon as you plug a cable onto the external SCSI
connector the internal terminator of the system is disabled. It also
means that you should not leave unterminated cables plugged into
the machine.AlphaStation 400 series have an SRM variable that controls
termination. In case you have external SCSI devices connected you
must set this SRM variable using>>>SET CONTROL_SCSI_TERM EXTERNAL.If only internal SCSI devices are present use:>>>SET CONTROL_SCSI_TERM INTERNALFor the AlphaStation-[24][05]00 machines the kernel config file
must contain:options DEC_2100_A50
cpu EV4AlphaStation 500 and 600 (Alcor &
Maverick for EV5, Bret for EV56)AS500 and 600 were the high-end EV5 / PCI based workstations.
EV6 based machines have in the meantime taken their place as front
runners. AS500 is a desktop in a dark blue case (TopGun blue),
AS600 is a sturdy desk-side box. AS600 has a nice LCD panel to observe
the early stages of SRM startup.Features:21164 EV5 CPU at 266, 300, 333, 366, 400, 433, 466, or
500 MHz (AS500) or at 266, 300 or 333 MHz (AS600)21171 or 21172 (Alcor) core logic chip-setCache:2 or 4 Mb L3 / Bcache (AS600 at 266 MHz)4 Mb L3 / Bcache (AS600 at 300 MHz)2 or 8 Mb L3 / Bcache (8 Mb on 500 MHz version only)2 to 16 Mb L3 / Bcache (AS600; 3 cache-SIMM slots)memory buswidth: 256 bitsAS500 memory:industry standard 72 bit wide buffered DIMMs8 DIMM slotsinstalled in sets of 4maximum memory is 1 GB (512 Mb max on 333 MHz CPUs)uses ECC AS600 memory:industry standard 36 bit Fast Page Mode SIMMs32 SIMM slotsinstalled in sets of 8maximum memory is 1 GBuses ECCQlogic 1020 based wide SCSI bus (1 bus/chip for AS500,
2 buses/chip for AS600)21040 based 10 Mbit Ethernet adapter, both Thinwire
and UTP connectorsexpansion:AS500:3 32-bit PCI slots1 64-bit PCI slotAS600:2 32-bit PCI slot3 64-bit PCI slots1 PCI/EISA physically shared slot3 EISA slots1 PCI and 1 EISA slot are occupied by default21050 PCI-to-PCI bridge chipIntel 82375EB PCI-EISA bridge (AS600 only)2 16550A serial ports1 parallel port16 bit audio Windows Sound System, in a dedicated slot (AS500)
in EISA slot (AS600, this is an ISA card)PS/2 keyboard and mouse portEarly machines had Fast SCSI interfaces, later ones are Ultra
SCSI capable. AS500 shares its single SCSI bus with internal and external
devices. For a Fast SCSI bus you are limited to 1.8 meters bus
length external to the box. The AS500 Qlogic ISP1020A chip can be set
to run in Ultra mode by setting a SRM variable. &os; however follows
the Qlogic chip errata and limits the bus speed to Fast.Beware of ancient SRM versions on AS500. When you see weird
SCSI speeds being reported by &os; likecd0 at isp0 bus 0 target 4 lun 0
cd0: <DEC RRD45 DEC 0436> Removable CD-ROM SCSI-2 device
cd0: 250.000MB/s transfers (250.000MHz, offset 12) it is time to do a SRM console firmware upgrade.AS600 has one Qlogic SCSI chip dedicated to the internal devices
whereas the other Qlogic SCSI chip is dedicated to external SCSI devices.
In AS500 DIMMs are installed in sets of 4, in physically
interleaved layout. So, a bank of 4 DIMMs is not
4 physically adjacent DIMMs.In AS600 the memory SIMMs are placed onto two memory daughter
cards. SIMMs are installed in sets of 8. Both memory daughter cards must
be populated identically.Note that both AS500 and AS600 are EISA machines. This means
you have to run the EISA Configuration Utility (ECU) from floppy
after adding EISA cards or to change things like the configuration
settings of the onboard I/O. For AS500 which does not have a physical
EISA slot the ECU is used to configure the onboard sound interface
etc.AS500 onboard sound can be used by adding a line likedevice pcmto the kernel configuration file.Using the ECU I configured my AS500 to use IRQ 10, port 0x530,
drq 0. Corresponding entries along with flags 0x10011 must go into
the device.hints file. Note that the flags value is rather non-standard.
AS600 has a peculiarity for its PCI slots. AS600 (or rather the
PCI expansion card containing the SCSI adapters) does not allow I/O port
mapping, therefore all devices behind it must use memory mapping. If you
have problems getting the Qlogic SCSI adapters to work, add the following
option to /boot/loader.rc:set isp_mem_map=0xffThis may need to be typed at the boot loader prompt before booting the
installation kernel.For the AlphaStation-[56]00 machines the kernel config file
must contain:options DEC_KN20AA
cpu EV5AlphaServer 1000 (Mikasa),
1000A (Noritake) and 800(Corelle)The AlphaServer 1000 and 800 range of machines are intended as
departmental servers. They come in quite some variations in packaging
and mainboard/cpu. Generally speaking there are 21064 (EV4) CPU based
machines and 21164 (EV5) based ones. The CPU is on a daughter card, and
the type of CPU (EV4 or EV5) must match the mainboard in use.AlphaServer 800 has a much smaller mini tower case, it lacks the
StorageWorks SCSI hot-plug chassis. The main difference between AS1000
and AS1000A is that AS1000A has 7 PCI slots whereas AS1000 only has 3
PCI slots and has EISA slots instead.AS800 with an EV5/400 MHz CPU was later re-branded to become a
DIGITAL Server 3300[R], AS800 with an EV5/500 MHz
CPU was later re-branded to become a
DIGITAL Server 3305[R].Features:21064 EV4[5] CPU at 200, 233 or 266 MHz
21164 EV5[6] CPU at 300, 333 or 400 MHz (or 500 MHz for
AS800 only)memory:buswidth: 128 bit with ECCAS1000[A]:72pin 36 bit Fast Page Mode SIMMs, 70ns or better16 (EV5 machines) or 20 (EV4 machines) SIMM slotsmax memory is 1 GBuses ECCAS800: Uses 60ns 3.3 Volts EDO DIMMsembedded VGA (on some mainboard models)3 PCI, 2 EISA, 1 64-bit PCI/EISA combo (AS800)7 PCI, 2 EISA (AS1000A)2 PCI, 1 EISA/PCI, 7 EISA (AS1000)embedded SCSI based on Symbios 810 [AS1000] or
Qlogic 1020 [AS1000A]AS1000 based machines come in multiple enclosure types. Floor
standing, rack-mount, with or without StorageWorks SCSI chassis etc.
The electronics are the same.AS1000-systems: All EV4 based machines use standard PS/2 style
36 bit 72pin SIMMs in sets of 5. The fifth SIMM is used for ECC.
All EV5 based machines use standard PS/2 style 36 bit 72pin SIMMs in sets
of 4. The ECC is done based on the 4 extra bits per SIMM
(4 bits out of 36). The EV5 mainboards have 16 SIMM slots,
the EV4 mainboards have 20 slots. AS800 machines use DIMMs in sets of 4. DIMM installation must
start in slots marked bank 0. A bank is four physically adjacent slots.
The biggest size DIMMs must be installed in bank 0 in case 2 banks
of different DIMM sizes are used. Max memory size is 2GB. Note
that these are EDO DIMMs.The AS1000/800 are somewhat stubborn when it comes to serial
consoles. They need>>> SET CONSOLE SERIALbefore they go for
a serial console. Pulling the keyboard from the machine is not sufficient,
like it is on most other Alpha models. Going back to a graphical console
needs>>> SET CONSOLE GRAPHICSat the serial console.For AS800 you want to check if your Ultra-Wide SCSI is indeed
in Ultra mode. This can be done using the
EEROMCFG.EXE utility that is
on the Console Firmware Upgrade CDROM.For the AlphaServer1000/1000A/800 machines the kernel config
file must contain:options DEC_1000A
cpu EV4 # depends on the CPU model installed
cpu EV5 # depends on the CPU model installedDS10/VS10/XP900 (Webbrick) / XP1000
(Monet) / DS10L (Slate)Webbrick and Monet are high performance workstations/servers
based on the EV6 CPU and the Tsunami chipset. Tsunami is also used in
much higher-end systems and as such has plenty of performance to offer.
DS10, VS10 and XP900 are different names for essentially the same system.
The differences are the software and options that are supported. DS10L
is a DS10 based machine in a 1U high rackmount enclosure. DS10L is
intended for ISPs and for HPTC clusters (e.g. Beowulf)Webbrick / Slate21264 EV6 CPU at 466 MHzL2 / Bcache: 2MB, ECC protectedmemory bus: 128 bit via crossbar, 1.3GB/sec memory
bandwidthmemory:industry standard 200 pin 83 MHz buffered
ECC SDRAM DIMMs4 DIMM slots for DS10; 2GB max memory2 DIMM slots for DS10L; 1GB max memoryDIMMs are installed in pairs of 221271 Core Logic chipset (Tsunami)2 on-board 21143 Fast Ethernet controllersAcerLabs M5237 (Aladdin-V) USB controller (disabled)AcerLabs M1533 PCI-ISA bridgeAcerLabs Aladdin ATA-33 controller embedded dual EIDE expansion: 3 64-bit PCI slots and 1 32-bit PCI slot.
DS10L has a single 64bit PCI slot2 16550A serial ports1 parallel port2 USBPS/2 keyboard & mouse portThe system has a smart power controller. This means that parts
of the system remain powered when it is switched off (like an ATX-style
PC power supply). Before servicing the machine remove the
power cord.The smart power controller is called the RMC. When enabled,
typing EscapeEscapeRMC on serial port 1
will bring you to the RMC prompt. RMC allows you to powerup or powerdown,
reset the machine, monitor and set temperature trip levels etc. RMC
has its own builtin help.Webbrick is shipped in a desktop-style case similar to the older
21164 Maverick workstations but this case
offers much better access
to the components. If you intend to build a farm you can rackmount them
in a 19-inch rack; they are 3U high. Slate is 1U high but has only
one PCI slot.DS10 has 4 DIMM slots. DIMMs are installed as pairs. Please note
that DIMM pairs are not installed in adjacent DIMM sockets but rather
physically interleaved. DIMM sizes of 32, 64, 128, 256 and 512 Mbytes
are supported.When 2 pairs of identical-sized DIMMs are installed DS10 will
use memory interleaving for increased performance. DS10L, which has
only 2 DIMM slots cannot do interleaving.Starting with SRM firmware version 5.9 you can boot from
Adaptec 2940-series adapters in addition to the usual set of Qlogic
and Symbios/NCR adapters.The base model comes with a FUJITSU 9.5GB ATA disk as its boot
device. &os; works just fine using EIDE disks on Webbrick. DS10 has
2 IDE interfaces on the mainboard. Machines destined for Tru64 Unix or
VMS are standard equipped with Qlogic-driven Ultra-SCSI disksOn the PCI bus 32 and 64 bit cards are supported, in 3.3V and
5V variants.The USB ports are not supported and are disabled by the
SRM console in all recent SRM versions.The kernel config file must contain:options DEC_ST6600
cpu EV5Contrary to expectation there is no cpu EV6
defined for inclusion in the kernel config file.
The cpu EV5 is mandatory to keep &man.config.8;
happy.Monet21264 EV6 at 500 MHz
21264 EV67 at 500 or 667 MHz (XP1000G, codenamed Brisbane)
CPU is mounted on a daughter-card which is field-upgradableL2 / Bcache: 4MB, ECC protectedmemory bus: 256 bitmemory: 128 or 256 Mbytes 100 MHz (PC100) 168 pin
JEDEC standard, registered ECC SDRAM DIMMs21271 Core Logic chip-set (Tsunami)1 on-board 21143 Ethernet controllerCypress 82C693 USB controllerCypress 82C693 PCI-ISA bridgeCypress 82C693 controllerexpansion: 2 independent PCI buses, driven by high-speed I/O
channels called hoses:hose 0: (the upper 3 slots)
2 64-bit PCI slots
1 32-bit PCI slot
hose 1: (the bottom 2 slots)
2 32-bit PCI slots (behind a 21154 PCI-PCI bridge)
2 of the 64-bit PCI slots are for
full-length cardsall of the 32-bit PCI slots are for short cards1 of the 32-bit PCI slots is physically shared
with an ISA slotall PCI slots run at 33MHz1 Ultra-Wide SCSI port based on a Qlogic 1040 chip2 16550A serial port1 parallel portPS/2 keyboard & mouse portembedded 16-bit ESS ES1888 sound chip2 USB portsgraphics options: ELSA Gloria Synergy or
DEC/Compaq PowerStorm 3D accelerator cardsMonet is housed in a mini-tower like enclosure quite similar
to the Miata box.The on-board Qlogic UW-SCSI chip supports up to 4 internal
devices. There is no external connector for the on-board SCSI.For 500 MHz CPUs 83 MHz DIMMs will do. Compaq specifies PC100
DIMMs for all CPU speeds. DIMMs are installed in sets of 4, starting
with the DIMM slots marked 0 Memory capacity is max 4 GB.
DIMMs are installed physically interleaved, note the
markings of the
slots. Memory bandwidth of Monet is twice that of Webbrick. The DIMMs
live on the CPU daughter-card. Note that the system uses ECC RAM so you
need DIMMs with 72 bits (not the generic PC-class 64 bit DIMMs)The EIDE interface is usable / SRM bootable so &os; can be rooted
on an EIDE disk. Although the Cypress chip has potential for 2
EIDE channels Monet uses only one of them.The USB interface is supported by &os;.If you experience
problems trying to use the USB interface please check if
the SRM variable usb_enable is set to
on. You can change this by
performing:>>>SET USB_ENABLE ONDon"t try to use Symbios-chip based SCSI
adapters in the PCI slots connected to hose 1. There is a
not-yet-found &os; bug that prevents this from working
correctly.Not all VGA cards will work behind the PCI-PCI
bridge (so in slots 4 and 5). Only cards that implement
VGA-legacy addressing
correctly will work. Workaround is to put the VGA card
before the bridge.The sound chip is not currently supported with &os;. The kernel config file must contain:options DEC_ST6600
cpu EV5Contrary to expectation there is no
cpu EV6 defined for inclusion in the kernel
config file. The cpu EV5 is mandatory to
keep &man.config.8; happy.DS20/DS20E (Goldrush)Features:21264 EV6 CPU at 500 or 670 MHzdual CPU capable machineL2 / Bcache: 4 Mbytes per CPUmemory bus: dual 256 bit wide with crossbar switchmemory:SDRAM DIMMsinstalled in sets of 416 DIMM slots, max. 4GBuses ECC21271 Core Logic chip-set
(Tsunami)embedded Adaptec ? Wide Ultra SCSIexpansion:2 independent PCI buses, driven
by high-speed I/O channels called hoses6 64-bit PCI slots, 3 per hose1 ISA slotDS20 needs>>>SET CONSOLE SERIALbefore it goes for a serial console. Pulling the keyboard from
the machine is not sufficient. Going back to a graphical console
needs>>>SET CONSOLE GRAPHICSat the serial console.
Confusing is the fact that you will get SRM console
output on the graphics console with the console set to serial,
but when &os; boots it honors the CONSOLE
variable setting and all the boot messages as well as the login
prompt will go to the serial port.The DS20 is housed in a fat cube-like enclosure. The
enclosure also contains a StorageWorks SCSI hot-swap shelf for a
maximum of seven 3.5" SCSI devices. The DS20E is in a sleeker
case, and lacks the StorageWorks shelf.The system has a smart power controller. This means that parts
of the system remain powered when it is switched off (like an ATX-style
PC power supply). Before servicing the machine remove the
power cord(s).The smart power controller is called the RMC. When enabled,
typing EscapeEscapeRMC on serial port 1
will bring you to the RMC prompt. RMC allows you to powerup or powerdown,
reset the machine, monitor and set temperature trip levels etc. RMC
has its own builtin help.The embedded Adaptec SCSI chip on the DS20 is disabled and
is therefore not usable under &os;.Starting with SRM firmware version 5.9 you can boot from
Adaptec 2940-series adapters in addition to the usual set of
Qlogic and Symbios/NCR adapters. This unfortunately does not
include the embedded Adaptec SCSI chips.If you are using banks of DIMMs of different sizes the
biggest DIMMs should be installed in the DIMM slots marked
0 on the mainboard. The DIMM slots should be
filled in order so after bank 0 install in bank 1
and so on.Don't try to use Symbios-chip based SCSI adapters in the
PCI slots connected to hose 1. There is a not-yet-found &os; bug
that prevents this from working correctly. DS20 ships by default
with a Symbios on hose 1 so you have to move this card before
you can install/boot &os; on it.The kernel config file must contain:options DEC_ST6600
cpu EV5Contrary to expectation there is no cpu EV6
defined for inclusion in the kernel config file.
The cpu EV5 is mandatory to keep &man.config.8;
happy.AlphaPC 264DP / UP2000UP2000 is built by Alpha Processor Inc.Features:21264 EV6 CPU at 670 MHzdual CPU capableL2 / Bcache: 4 Mbytes per CPUmemory bus: 256 bitmemory: SDRAM DIMMs installed in sets of 4, uses
ECC, 16 DIMM slots, max. 4GB21272 Core Logic chip-set (Tsunami)embedded Adaptec AIC7890/91 Wide Ultra SCSI2 embedded IDE based on Cypress 82C693 chipsembedded USB via Cypress 82C693expansion:2 independent PCI buses, driven
by high-speed I/O channels called hoses6 64-bit PCI slots, 3 per hose1 ISA slotCurrently a maximum of 2GB memory is supported by &os;.The on-board Adaptec is not bootable but works with &os;
4.0 and later as a datadisk-only SCSI bus.Busmaster DMA is supported on the first IDE interface
only.The kernel config file must contain:options DEC_ST6600
cpu EV5Contrary to expectation there is no cpu
EV6 defined for inclusion in the kernel config
file. The cpu EV5 is mandatory to keep
&man.config.8; happy.AlphaServer 2000 (DemiSable), 2100
(Sable), 2100A (Lynx)The AlphaServer 2[01]00 machines are intended as departmental
servers. This is medium iron. They are multi-CPU machines, up to 2
CPUs (AS2000) or 4 CPUs (2100[A]) can be installed. Both floor-standing
and 19" rackmount boxes exist. Rackmount variations have
different numbers of I/O expansion slots, different max number
of CPUs and different maximum memory size. Some of the boxes come
with an integral StorageWorks shelf to house hot-swap SCSI disks.
There was an upgrade program available to convert your Sable
machine into a Lynx by swapping the I/O backplane (the C-bus
backplane remains). CPU upgrades were available as well.21064 EV4[5] CPU[s] at 200, 233, 275 MHz or
21164 EV5[6] CPU[s]s at 250, 300, 375, 400 MHzcache: varies in size with the CPU model; 1, 4 or
8Mbyte per CPUembedded floppy controller driving a 2.88 Mbytes driveembedded 10Mbit 21040 Ethernet [AS2100 only]2 serial ports1 parallel portPS/2 style keyboard & mouse portThe CPUs spec-ed as 200 MHz are in reality running at
190 MHz. Maximum number of CPUs is 4. All CPUs must be of the
same type/speed.If any of the processors are ever marked as failed, they will
remain marked as failed even after they have been replaced (or reseated)
until you issue the command>>>CLEAR_ERROR ALLon the SRM console and power-cycle the machine. This may be true
for other modules (IO and memory) as well, but it has not been verified.
The machines use dedicated memory boards. These boards live on
a 128 bit C-bus shared with the CPU boards. DemiSable supports up
to 1GB, Sable up to 2GB. One of the memory bus slots can either
hold a CPU or a memory card. A 4 CPU machine can have a maximum of
2 memory boards.Some memory board models house SIMMs. These are called SIMM
carriers. There are also memory modules that have soldered-on memory
chips instead of SIMMs. These are called flat memory
modules.SIMM boards are used in sets of eight 72-pin 36 bit FPM
memory of 70ns or faster. SIMM types supported are 1Mb x36 bit
(4 Mbyte) and 4Mb x36 bit (16 Mbyte). Each memory board can house
4 banks of SIMMs. SIMM sizes can not be mixed on a single memory
board. The first memory module must be filled with SIMMs before
starting to fill the next memory module. Note that the spacing
between the slots is not that big, so make sure your SIMMs fit
physically (before buying them..)Both Lynx and Sable are somewhat stubborn when it comes to serial
consoles. They need>>> SET CONSOLE SERIALbefore they go for a serial console.
Pulling the keyboard from the machine is not sufficient, like it is
on many other Alpha models. Going back to a graphical console needs>>>SET CONSOLE GRAPHICSat the serial console. On Lynx keep the VGA card in
one of the primary PCI slots. EISA VGA cards are not slot sensitive.
The machines are equipped with a small OCP
(Operator Control Panel) LCD screen. On this screen the self-test
messages are displayed during system initialization. You can put
your own little text there by using the SRM:>>>SET OCP_TEXT "FreeBSD"
The SRM>>>SHOW FRUcommand produces an overview of your configuration
with module serial numbers, hardware revisions and error log counts.
Both Sable, DemiSable and Lynx have Symbios 810 based
Fast SCSI on-board. Check if it is set to Fast SCSI speed
by>>>SHOW PKA0_FASTWhen set to 1 it is negotiating for Fast speeds.>>>SET PKA0_FAST 1enables Fast SCSI speeds.AS2100[A] come equipped with a StorageWorks 7 slot SCSI
cage. A second cage can be added inside the cabinet. AS2000
has a single 7 slot SCSI cage, which cannot be expanded with
an additional one. Note that the slot locations in these cages
map differently to SCSI IDs compared to the standard StorageWorks
shelves. Slot IDs from top to bottom are 0, 4, 1, 5, 2, 6, 3
when using a single bus configuration.The cage can also be set to provide two independent SCSI
buses. This is used for embedded RAID controllers like the
KZPSC (Mylex DAC960). Slot ID assignments for split bus are,
from top to bottom: 0A, 0B, 1A, 1B, 2A, 2B, 3A, 3B.
Where A and B signify a SCSI bus. In a single bus configuration the
terminator module on the back of the SCSI cage is on the TOP. The jumper
module is on the BOTTOM. For split bus operation these two modules are
reversed. The terminator can be distinguished from the jumper
by noting the chips on the terminator. The jumper does not have
any active components on it.DemiSable has 7 EISA slots and 3 PCI slots. Sable has
8 EISA and 3 PCI slots. Lynx, being newer, has 8 PCI
and 3 EISA slots. The Lynx PCI slots are grouped in
sets of 4. The 4 PCI slots closest to the CPU/memory
slots are the primary slots, so logically before the PCI bridge chip.
Note that contrary to expectation the primary PCI slots are the highest
numbered ones (PCI4 - PCI7).Make sure you run the EISA Configuration Utility (from floppy)
when adding/change expansion cards in EISA slots or after
upgrading your console firmware. This is done by inserting the
ECU floppy and typing>>>RUNECUEISA slots are currently unsupported, but the Compaq Qvision
EISA VGA adapter is treated as an ISA device. It therefore
works OK as a console.A special Extended I/O module for use on the C-bus was
planned-for. If they ever saw daylight is unknown. In any case
&os; has never been verified with an ExtIO module.The machines can be equipped with redundant power supplies. Note
that the enclosure is equipped with interlock switches that switch
off power when the enclosure is opened. The system's cooling
fans are speed controlled. When the machine has more than 2
CPUs and more than 1 memory board dual power supplies
are mandatory.The kernel config file must contain:options DEC_2100_A500
cpu EV4 #dependent on CPU model installed
cpu EV5 #dependent on CPU model installedAlphaServer 4x00 (Rawhide)The AlphaServer 4x00 machines are intended as small enterprise
servers. Expect a 30" high pedestal cabinet or alternatively
the same system box in a 19" rack. This is medium iron, not
a typical hobbyist system. Rawhides are multi-CPU machines, up to
4 CPUs can be in a single machine. Basic disk storage is housed in
one or two StorageWorks shelves at the bottom of the pedestal. The
Rawhides intended for the NT market are designated DIGITAL
Server 7300 (5/400 CPU), DIGITAL Server 7305 (5/533 CPU). A
trailing R on the part-number means a rackmount variant.Features:21164 EV5 CPUs at 266, 300 MHz or 21164A EV56
CPUs at 400, 466, 533, 600 and 666 Mhzcache: 4 Mbytes per CPU. EV5 300 MHz was also
available cache-less. 8 Mbytes for EV5 600Mhzmemory bus: 128 bit with ECCembedded floppy controller2 serial ports1 parallel portPS/2 style keyboard & mouse portRawhide uses a maximum of 8 RAM modules. These modules are used
in pairs and supply 72 bits to the bus (this includes ECC bits).
Memory can be EDO RAM or synchronous DRAM. A fully populated Rawhide
has 4 pairs of memory modules. Given the choice use SDRAM for
best performance. The highest capacity memory board must be in
memory slot 0. A mix of memory board sizes is allowed. A mix
of EDO and SDRAM is also reported as working (assuming you don't
try to mix EDO and SDRAM in one module pair). A mix of EDO and SDRAM
results in the entire memory subsystem running at
the slower EDO timingRawhide has an embedded Symbios 810 chip that gives you a
narrow fast-SCSI bus. Generally only the SCSI CDROM is driven by
this interface.Rawhides are available with a 8 64-bit PCI / 3 EISA
slot expansion backplanes (called Saddle modules). There
are 2 separate PCI buses, PCI0 and PCI1. PCI0 has 1 dedicated
PCI slot and (shared) 3 PCI/EISA slots. PCI0 also has a
PCI/EISA bridge that drives things like the serial and
parallel ports, keyboard/mouse etc. PCI1 has 4 PCI slots
and a Symbios 810 SCSI chip. VGA console cards must be installed
in a slot connected to PCI0.The current &os; implementation has problems in handling
PCI bridges. There is currently a limited fix in place which allows
for single level, single device PCI bridges. The fix allows the use of
the Digital supplied Qlogic SCSI card which sits behind
a 21054 PCI bridge chip.EISA slots are currently unsupported, but the Compaq Qvision
EISA VGA adapter is treated as an ISA device. It therefore works
OK as a console.Rawhide employs an I2C based power controller system. If
you want to be sure all power is removed from the system remove the
mains cables from the system.The kernel config file must contain:options DEC_KN300
cpu EV5AlphaServer 1200 (Tincup) and AlphaStation
1200 (DaVinci)The AlphaServer 1200 machine is the successor to the
AlphaServer 1000A. It uses the same enclosure the 1000A uses,
but the logic is based on the AlphaServer 4000 design. These
are multi-CPU machines, up to 2 CPUs can be in a single machine.
Basic disk storage is housed in a StorageWorks shelves
The AS1200 intended for the NT market were designated DIGITAL
Server 5300 (5/400 CPU) and DIGITAL Server 5305 (5/533 CPU).Features:21164A EV56 CPUs at 400 or 533 Mhzcache: 4 Mbytes per CPUmemory bus: 128 bit with ECC, DIMM memory on two
memory daughter boardsembedded floppy controller2 serial ports1 parallel portPS/2 style keyboard & mouse portAS1200 uses 2 memory daughter cards. On each of these cards
are 8 DIMM slots. DIMMs must be installed in pairs. The maximum
memory size is 4 GBytes. Slots must be filled in order and slot
0 must contain the largest size DIMM if different sized DIMMs are
used. AS1200 employs fixed starting addresses for DIMMs, each
DIMM pair starts at a 512 Mbyte boundary. This means that if
DIMMs smaller than 256 Mbyte are used the system's physical memory
map will contain holes. Supported DIMM sizes are 64 Mbytes
and 256 Mbytes. The DIMMs are 72 bit SDRAM based, as the
system employs ECC.&os; currently supports up to 2GBytesAS1200 has an embedded Symbios 810 drive Fast SCSI bus.Tincup has 5 64-bit PCI slots, one 1 32-bit PCI slot and one
EISA slot (which is physically shared with one of the 64-bit PCI slots).
There are 2 separate PCI buses, PCI0 and PCI1. PCI0 has the 32-bit PCI
slot and the 2 top-most 64-bit PCI slots. PCI0 also has an Intel 82375EB
PCI/EISA bridge that drives things like the serial and parallel ports,
keyboard/mouse etc. PCI1 has 4 64-bit PCI slots and a Symbios 810
SCSI chip. VGA console cards must be installed in a slot
connected to PCI0.The system employs an I2C based power controller system.
If you want to be sure all power is removed from the system remove
the mains cables from the system. Tincup uses dual power supplies
in load-sharing mode and not as a redundancy pair.The kernel config file must contain:options DEC_KN300
cpu EV5AlphaServer 8200 and 8400 (TurboLaser)The AlphaServer 8200 and 8400 machines are enterprise servers.
Expect a tall 19" cabinet (8200) or fat (8400) 19" rack.
This is big iron, not a hobbyist system. TurboLasers are multi-CPU
machines, up to 12 CPUs can be in a single machine. The TurboLaser
System Bus (TLSB) allows 9 nodes on the AS8400 and 5 nodes on
the AS8200. TLSB is 256 bit data, 40 bit address allowing 2.1
GBytes/sec. Nodes on the TLSB can be CPUs, memory or I/O. A
maximum of 3 I/O ports are supported on a TLSB.Basic disk storage is housed in a StorageWorks shelf.
AS8400 uses 3 phase power, AS8200 uses single phase power.Features:21164 EV5/EV56 CPUs at up to 467 MHz or 21264 EV67 CPUs at
up to 625 MHzone or two CPUs per CPU modulecache: 4Mbytes B-cache per CPUmemory bus: 256 bit with ECCmemory: big memory modules that plug into the TLSB,
which in turn hold special SIMM modules. Memory modules come
in varying sizes, up to 4 GBytes a piece. Uses ECC (8 bits
per 64 bits of data) 7 memory modules max for AS8400,
3 modules max for AS8200. Maximum memory is 28 GBytes.expansion: 3 system I/O ports that allow up to
12 I/O channels each I/O channel can connect to
XMI, Futurebus+ or PCI boxes&os; supports (and has been tested with) up to 2 GBytes
of memory on TurboLaser. There is a trade-off to be made between
TLSB slots occupied by memory modules and TLSB slots occupied by
CPU modules. For example you can have 28GBytes of memory but only
2 CPUs (1 module) at the same time.Only PCI expansion is supported on &os;. XMI or
Futurebus+ (which are AS8400 only) are both unsupported.The I/O port modules are designated KFTIA or KFTHA. The
I/O port modules supply so called hoses that connect to
up to 4 (KFTHA) PCI buses or 1 PCI bus (KFTIA). KFTIA has
embedded dual 10baseT Ethernet, single FDDI, 3 SCSI Fast
Wide Differential SCSI buses and a single Fast Wide Single Ended
SCSI bus. The FWSE SCSI is intended for the CDROM.KFTHA can drive via each of its 4 hoses a DWLPA or DWLPB
box. The DWLPx house a 12 slots 32 bit PCI backplane. Physically
the 12 slots are 3 4-slot buses but to the software it appears
as a single 12 slots PCI bus. A fully expanded AS8x00 can have
3 (I/O ports) times 4 (hoses) times 12 (PCI slots/DWLPx) =
144 PCI slots. The maximum bandwidth per KFTHA is 500
Mbytes/second. DWLPA can also house 8 EISA cards, 2 slots
are PCI-only, 2 slots are EISA only. Of the 12 slots 2
are always occupied by an I/O and connector module. DWLPB are the
prefered I/O boxes.For best performance distribute high bandwidth
(FibreChannel, Gigabit Ethernet) over multiple hoses and/or
multiple KFTHA/KFTIA.Currently PCI expansion cards containing PCI bridges are
not usable with &os;. Don't use them at this time.The single ended narrow SCSI bus on the KFTIA will turn up as
the fourth SCSI bus. The 3 fast-wide
differential SCSI buses of the KFTIA precede it. AS8x00 are generally run with serial consoles. Some
newer machines might have a graphical console of some sorts
but &os; has only been tested on a serial console.For serial console usage either change
/etc/ttys to have:console "/usr/libexec/getty std.9600" unknown on secureas the console entry, or addzs0 "/usr/libexec/getty std.9600" unknown on secureFor the AlphaServer 8x00 machines the kernel config file
must contain:options DEC_KN8AE # Alpha 8200/8400 (Turbolaser)
cpu EV5Contrary to expectation there is no cpu
EV6 defined for inclusion in the kernel config
file. The cpu EV5 is mandatory to keep
&man.config.8; happy.Alpha Processor Inc. UP1000The UP1000 is an ATX mainboard based on the 21264a
CPU which itself lives in a Slot B module. It is normally housed
in an ATX tower enclosure.Features:21264a Alpha CPU at 600 or 700 MHz in a Slot B
module (includes cooling fans)memory bus: 128 bits to the L2 cache,
64 bits from Slot B to the AMD-751on-board Bcache / L2 cache: 2MB (600Mhz) or
4MB (700Mhz)AMD AMD-751 (Irongate)
system controller chipAcer Labs M1543C PCI-ISA bridge controller /
super-IO chipPS/2 mouse & keyboard portmemory: 168-pin PC100 unbuffered SDRAM DIMMS, 3 DIMM slots
DIMM sizes supported are 64, 128 or 256 Mb in size2 16550A serial port1 ECP/EPP parallel portfloppy interface2 embedded Ultra DMA33 IDE interface2 USB portsexpansion:4 32 bit PCI slots2 ISA slots1 AGP slotSlot B is a box-like enclosure that houses a
daughter-board for the CPU and cache. It has 2 small fans for
cooling. Loud fans..The machine needs ECC capable DIMMs, so 72 bit ones.
This does not appear to be documented in the UP1000 docs. The
system accesses the serial EEPROM on the DIMMs via the SM bus.
Note that if only a single DIMM is used it must be installed in
slot 2. This is a bit counter-intuitive.The UP1000 needs a 400Watt ATX power supply according
to the manufacturer. This might be a bit overly
conservative/pessimistic judging from the power consumption of
the board & cpu. But as always you will have to take your
expansion cards and peripherals into account. The M1543C chip
contains power management functionality & temperature monitoring
(via I2C / SM bus).Chances are that your UP1000 comes by default with
AlphaBios only. The SRM console firmware is available from
the Alpha Processor Inc. web site. It is currently available in
a beta version which was successfully used during the port of &os;
to the UP1000. The embedded Ultra DMA EIDE ports are bootable by the
SRM console.UP1000 SRM can boot off an Adaptec 294x adapter. Under high
I/O load conditions machine lockups have been observed using
the Adaptec 294x. A Symbios 875 based card works just fine,
using the sym driver. Most likely other cards based on the Symbios
chips that the sym driver supports will work as well.The USB interfaces are disabled by the SRM console and
have not (yet) been tested with &os;.For the UP1000 the kernel config file must contain:options API_UP1000 # UP1000, UP1100 (Nautilus)
cpu EV5Alpha Processor Inc. UP1100The UP1100 is an ATX mainboard based on the 21264a CPU running
at 600 MHz. It is normally housed in an ATX tower enclosure.Features:21264a Alpha EV6 CPU at 600 or 700 MHzmemory bus: 100MHz 64-bit (PC-100 SDRAM), 800 MB/s memory
bandwidthon-board Bcache / L2 cache: 2MbAMD AMD-751 (Irongate) system controller
chipAcer Labs M1535D PCI-ISA bridge controller /
super-IO chipPS/2 mouse & keyboard portmemory: 168-pin PC100 unbuffered SDRAM DIMMS, 3 DIMM slots
DIMM sizes supported are 64, 128 or 256 Mb in size2 16550A serial port1 ECP/EPP parallel portfloppy interface2 embedded Ultra DMA66 IDE interface2 USB portexpansion: 3 32 bit PCI slots and 1 AGP2x slotSRM console code comes standard with the UP1100. The SRM lives
in 2Mbytes of flash ROM.The machine needs ECC capable DIMMs, so 72 bit ones.
This does not appear to be documented in the UP1100 docs. The
system accesses the serial EEPROM on the DIMMs via the SM bus.
Note that if only a single DIMM is used it must be installed in
slot 2. This is a bit counter-intuitive.The UP1100 needs a 400Watt ATX power supply according to
the manufacturer. This might be a bit overly conservative/pessimistic
judging from the power consumption of the board & cpu. But as
always you will have to take your expansion cards and
peripherals into account. The M1535D chip contains power
management functionality & temperature monitoring
(via I2C / SM bus using a LM75 thermal sensor).The UP1100 has an on-board 21143 10/100Mbit Ethernet
interface.The UP1100 is equipped with a SoundBlaster compatible audio
interface. Whether it works with &os; is as of yet unknown.The embedded Ultra DMA EIDE ports are bootable by
the SRM console.The UP1100 has 3 USB ports, 2 going external and one connected
to the AGP port.For the UP1100 the kernel config file must contain:options API_UP1000 # UP1000, UP1100 (Nautilus)
cpu EV5Contrary to expectation there is no cpu
EV6 defined for inclusion in the kernel config
file. The cpu EV5 is mandatory to keep
&man.config.8; happy.Alpha Processor Inc. CS20, Compaq DS20LThe CS20 is a 19", 1U high rackmount server based
on the 21264[ab] CPU. It can have a maximum of 2 CPUs. Compaq
sells the CS20 rebranded as the AlphaServer DS20L. DS20L has
833MHz CPUs.Features:21264a Alpha CPU at 667 MHz or 21264b 833 MHz
(max. 2 CPUs)memory bus: 100MHz 256-bit wide21271 Core Logic chipset (Tsunami)Acer Labs M1533 PCI-ISA bridge controller / super-IO chip
PS/2 mouse & keyboard portmemory: 168-pin PC100 PLL buffered/registered SDRAM DIMMS,
8 DIMM slots, uses ECC memory, min 256 Mbytes /
max 2 GBytes of memory2 16550A serial port1 ECP/EPP parallel portALI M1543C Ultra DMA66 IDE interfaceembedded dual Intel 82559 10/100Mbit Ethernetembedded Symbios 53C1000 Ultra160 SCSI controllerexpansion: 2 64 bit PCI slots (2/3 length)SRM console code comes standard with the CS20. The SRM
lives in 2Mbytes of flash ROM.The CS20 needs ECC capable DIMMs. Note that it
uses buffered DIMMs.The CS20 has an I2C based internal monitoring system for things
like temperature, fans, voltages etc. The I2C also supports
wake on LAN.Each PCI slot is connected to its own independent PCI bus
on the Tsunami.The embedded Ultra DMA EIDE ports are bootable by the
SRM console.The CS20 has an embedded slim-line IDE CD drive. There is
a front-accessible bay for a 1" high 3.5" SCSI hard-disk
drive with SCA connector.Note that there is no floppy disk drive (or a connector to
add one).The kernel config file must contain:options DEC_ST6600
cpu EV5Contrary to expectation there is no cpu
EV6 defined for inclusion in the kernel config
file. The cpu EV5 is mandatory to keep
&man.config.8; happy.Supported Hardware OverviewA word of caution: the installed base for &os; is not
nearly as large as for &os;/Intel. This means that the enormous
variation of PCI/ISA expansion cards out there has much less
chance of having been tested on alpha than on Intel. This is not
to imply they are doomed to fail, just that the chance of running
into something never tested before is much higher.
GENERIC
contains things that are known to work on Alpha only.The PCI and ISA expansion busses are fully supported. Turbo
Channel is not in GENERIC and has limited
support (see the relevant machine model info). The MCA bus is not
supported. The EISA bus is not supported for use with EISA
expansion cards as the EISA support code is lacking. ISA cards in
EISA slots are reported to work. The Compaq Qvision EISA VGA card
is driven in ISA mode and works OK as a console.1.44 Mbyte and 1.2 Mbyte floppy drives are supported.
2.88 Mbyte drives sometimes found in Alpha machines are supported up to
1.44Mbyte.ATA and ATAPI (IDE) devices are supported via the &man.ata.4;
driver framework. As most people run their Alphas with SCSI disks
it is not as well tested as SCSI. Be aware of boot-ability
restrictions for IDE disks. See the machine specific information.There is full SCSI support via the CAM layer for Adaptec
2940x (AIC7xxx chip-based), Qlogic family and Symbios. Be aware of
the machine-specific boot-ability issues for the various adapter
types.The Qlogic QL2x00 FibreChannel host adapters are fully
supported.If you want to boot your Alpha over the Ethernet you will
obviously need an Ethernet card that the SRM console
recognizes. This generally means you need a board with an 21x4x
Ethernet chip as that is what Digital used. These chips are driven
by the &os; &man.de.4; (older driver) or &man.dc.4; (newer
driver). Some new SRM versions are known to recognize the Intel
8255x Ethernet chips as driven by the &os; &man.fxp.4; driver. But
beware: the &man.fxp.4; driver is reported not to work correctly
with &os; (although it works excellently on &os;/x86).DEC DEFPA PCI FDDI network adapters are supported on alpha.In general the SRM console emulates a VGA-compatibility mode
on PCI VGA cards. This is, however, not guaranteed to work by
Compaq/DEC for each and every card type out there. When the SRM
thinks the VGA is acceptable &os; will be able to use it. The
console driver works just like on a &os;/intel machine.
Please note that VESA modes are not supported on Alpha,
so that leaves you with 80x25 consoles.In some Alpha machines you will find video adapters based
on TGA chips. The plain TGA adapter does not emulate VGA and is
therefore not usable for a &os; console. TGA2 cards have a basic
VGA compatibility mode and work fine as &os; consoles.The PC standard serial ports found on most
Alphas are supported.ISDN (i4b) is not supported on &os;/alpha.AcknowledgmentsIn compiling this file I used multiple information sources,
but the NetBSD Web
site proved to be an invaluable source of information. If
it wasn't for NetBSD/alpha there probably would not be a
&os;/alpha in the first place.People who kindly helped me create this section:&a.gallatin;&a.chuckr;&a.mjacob;&a.msmith;&a.obrien;Christian WeisgerberKazutaka YOKOTANick ManiscalcoEric SchnoebelenPeter van DijkPeter JeremyDolf de WaalWim Lemmers, ex-CompaqWouter Brackman, CompaqLodewijk van den Berg, Compaq