/*- * Copyright (c) 2002-2004 M. Warner Losh. * Copyright (c) 2000-2001 Jonathan Chen. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * */ /*- * Copyright (c) 1998, 1999 and 2000 * HAYAKAWA Koichi. All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by HAYAKAWA Koichi. * 4. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ /* * Driver for PCI to CardBus Bridge chips * * References: * TI Datasheets: * http://www-s.ti.com/cgi-bin/sc/generic2.cgi?family=PCI+CARDBUS+CONTROLLERS * * Written by Jonathan Chen * The author would like to acknowledge: * * HAYAKAWA Koichi: Author of the NetBSD code for the same thing * * Warner Losh: Newbus/newcard guru and author of the pccard side of things * * YAMAMOTO Shigeru: Author of another FreeBSD cardbus driver * * David Cross: Author of the initial ugly hack for a specific cardbus card */ #include __FBSDID("$FreeBSD$"); #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "power_if.h" #include "card_if.h" #include "pcib_if.h" #define DPRINTF(x) do { if (cbb_debug) printf x; } while (0) #define DEVPRINTF(x) do { if (cbb_debug) device_printf x; } while (0) #define PCI_MASK_CONFIG(DEV,REG,MASK,SIZE) \ pci_write_config(DEV, REG, pci_read_config(DEV, REG, SIZE) MASK, SIZE) #define PCI_MASK2_CONFIG(DEV,REG,MASK1,MASK2,SIZE) \ pci_write_config(DEV, REG, ( \ pci_read_config(DEV, REG, SIZE) MASK1) MASK2, SIZE) static void cbb_chipinit(struct cbb_softc *sc); static int cbb_pci_filt(void *arg); static struct yenta_chipinfo { uint32_t yc_id; const char *yc_name; int yc_chiptype; } yc_chipsets[] = { /* Texas Instruments chips */ {PCIC_ID_TI1031, "TI1031 PCI-PC Card Bridge", CB_TI113X}, {PCIC_ID_TI1130, "TI1130 PCI-CardBus Bridge", CB_TI113X}, {PCIC_ID_TI1131, "TI1131 PCI-CardBus Bridge", CB_TI113X}, {PCIC_ID_TI1210, "TI1210 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI1211, "TI1211 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI1220, "TI1220 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI1221, "TI1221 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI1225, "TI1225 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI1250, "TI1250 PCI-CardBus Bridge", CB_TI125X}, {PCIC_ID_TI1251, "TI1251 PCI-CardBus Bridge", CB_TI125X}, {PCIC_ID_TI1251B,"TI1251B PCI-CardBus Bridge",CB_TI125X}, {PCIC_ID_TI1260, "TI1260 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI1260B,"TI1260B PCI-CardBus Bridge",CB_TI12XX}, {PCIC_ID_TI1410, "TI1410 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI1420, "TI1420 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI1421, "TI1421 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI1450, "TI1450 PCI-CardBus Bridge", CB_TI125X}, /*SIC!*/ {PCIC_ID_TI1451, "TI1451 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI1510, "TI1510 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI1520, "TI1520 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI4410, "TI4410 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI4450, "TI4450 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI4451, "TI4451 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI4510, "TI4510 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI6411, "TI6411 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI6420, "TI6420 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI6420SC, "TI6420 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI7410, "TI7410 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI7510, "TI7510 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI7610, "TI7610 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI7610M, "TI7610 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI7610SD, "TI7610 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_TI7610MS, "TI7610 PCI-CardBus Bridge", CB_TI12XX}, /* ENE */ {PCIC_ID_ENE_CB710, "ENE CB710 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_ENE_CB720, "ENE CB720 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_ENE_CB1211, "ENE CB1211 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_ENE_CB1225, "ENE CB1225 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_ENE_CB1410, "ENE CB1410 PCI-CardBus Bridge", CB_TI12XX}, {PCIC_ID_ENE_CB1420, "ENE CB1420 PCI-CardBus Bridge", CB_TI12XX}, /* Ricoh chips */ {PCIC_ID_RICOH_RL5C465, "RF5C465 PCI-CardBus Bridge", CB_RF5C46X}, {PCIC_ID_RICOH_RL5C466, "RF5C466 PCI-CardBus Bridge", CB_RF5C46X}, {PCIC_ID_RICOH_RL5C475, "RF5C475 PCI-CardBus Bridge", CB_RF5C47X}, {PCIC_ID_RICOH_RL5C476, "RF5C476 PCI-CardBus Bridge", CB_RF5C47X}, {PCIC_ID_RICOH_RL5C477, "RF5C477 PCI-CardBus Bridge", CB_RF5C47X}, {PCIC_ID_RICOH_RL5C478, "RF5C478 PCI-CardBus Bridge", CB_RF5C47X}, /* Toshiba products */ {PCIC_ID_TOPIC95, "ToPIC95 PCI-CardBus Bridge", CB_TOPIC95}, {PCIC_ID_TOPIC95B, "ToPIC95B PCI-CardBus Bridge", CB_TOPIC95}, {PCIC_ID_TOPIC97, "ToPIC97 PCI-CardBus Bridge", CB_TOPIC97}, {PCIC_ID_TOPIC100, "ToPIC100 PCI-CardBus Bridge", CB_TOPIC97}, /* Cirrus Logic */ {PCIC_ID_CLPD6832, "CLPD6832 PCI-CardBus Bridge", CB_CIRRUS}, {PCIC_ID_CLPD6833, "CLPD6833 PCI-CardBus Bridge", CB_CIRRUS}, {PCIC_ID_CLPD6834, "CLPD6834 PCI-CardBus Bridge", CB_CIRRUS}, /* 02Micro */ {PCIC_ID_OZ6832, "O2Micro OZ6832/6833 PCI-CardBus Bridge", CB_O2MICRO}, {PCIC_ID_OZ6860, "O2Micro OZ6836/6860 PCI-CardBus Bridge", CB_O2MICRO}, {PCIC_ID_OZ6872, "O2Micro OZ6812/6872 PCI-CardBus Bridge", CB_O2MICRO}, {PCIC_ID_OZ6912, "O2Micro OZ6912/6972 PCI-CardBus Bridge", CB_O2MICRO}, {PCIC_ID_OZ6922, "O2Micro OZ6922 PCI-CardBus Bridge", CB_O2MICRO}, {PCIC_ID_OZ6933, "O2Micro OZ6933 PCI-CardBus Bridge", CB_O2MICRO}, {PCIC_ID_OZ711E1, "O2Micro OZ711E1 PCI-CardBus Bridge", CB_O2MICRO}, {PCIC_ID_OZ711EC1, "O2Micro OZ711EC1/M1 PCI-CardBus Bridge", CB_O2MICRO}, {PCIC_ID_OZ711E2, "O2Micro OZ711E2 PCI-CardBus Bridge", CB_O2MICRO}, {PCIC_ID_OZ711M1, "O2Micro OZ711M1 PCI-CardBus Bridge", CB_O2MICRO}, {PCIC_ID_OZ711M2, "O2Micro OZ711M2 PCI-CardBus Bridge", CB_O2MICRO}, {PCIC_ID_OZ711M3, "O2Micro OZ711M3 PCI-CardBus Bridge", CB_O2MICRO}, /* SMC */ {PCIC_ID_SMC_34C90, "SMC 34C90 PCI-CardBus Bridge", CB_CIRRUS}, /* sentinel */ {0 /* null id */, "unknown", CB_UNKNOWN}, }; /************************************************************************/ /* Probe/Attach */ /************************************************************************/ static int cbb_chipset(uint32_t pci_id, const char **namep) { struct yenta_chipinfo *ycp; for (ycp = yc_chipsets; ycp->yc_id != 0 && pci_id != ycp->yc_id; ++ycp) continue; if (namep != NULL) *namep = ycp->yc_name; return (ycp->yc_chiptype); } static int cbb_pci_probe(device_t brdev) { const char *name; uint32_t progif; uint32_t baseclass; uint32_t subclass; /* * Do we know that we support the chipset? If so, then we * accept the device. */ if (cbb_chipset(pci_get_devid(brdev), &name) != CB_UNKNOWN) { device_set_desc(brdev, name); return (BUS_PROBE_DEFAULT); } /* * We do support generic CardBus bridges. All that we've seen * to date have progif 0 (the Yenta spec, and successors mandate * this). */ baseclass = pci_get_class(brdev); subclass = pci_get_subclass(brdev); progif = pci_get_progif(brdev); if (baseclass == PCIC_BRIDGE && subclass == PCIS_BRIDGE_CARDBUS && progif == 0) { device_set_desc(brdev, "PCI-CardBus Bridge"); return (BUS_PROBE_GENERIC); } return (ENXIO); } /* * Still need this because the pci code only does power for type 0 * header devices. */ static void cbb_powerstate_d0(device_t dev) { u_int32_t membase, irq; if (pci_get_powerstate(dev) != PCI_POWERSTATE_D0) { /* Save important PCI config data. */ membase = pci_read_config(dev, CBBR_SOCKBASE, 4); irq = pci_read_config(dev, PCIR_INTLINE, 4); /* Reset the power state. */ device_printf(dev, "chip is in D%d power mode " "-- setting to D0\n", pci_get_powerstate(dev)); pci_set_powerstate(dev, PCI_POWERSTATE_D0); /* Restore PCI config data. */ pci_write_config(dev, CBBR_SOCKBASE, membase, 4); pci_write_config(dev, PCIR_INTLINE, irq, 4); } } /* * Print out the config space */ static void cbb_print_config(device_t dev) { int i; device_printf(dev, "PCI Configuration space:"); for (i = 0; i < 256; i += 4) { if (i % 16 == 0) printf("\n 0x%02x: ", i); printf("0x%08x ", pci_read_config(dev, i, 4)); } printf("\n"); } static int cbb_pci_attach(device_t brdev) { #if !(defined(NEW_PCIB) && defined(PCI_RES_BUS)) static int curr_bus_number = 2; /* XXX EVILE BAD (see below) */ uint32_t pribus; #endif struct cbb_softc *sc = (struct cbb_softc *)device_get_softc(brdev); struct sysctl_ctx_list *sctx; struct sysctl_oid *soid; int rid; device_t parent; parent = device_get_parent(brdev); mtx_init(&sc->mtx, device_get_nameunit(brdev), "cbb", MTX_DEF); sc->chipset = cbb_chipset(pci_get_devid(brdev), NULL); sc->dev = brdev; sc->cbdev = NULL; sc->exca[0].pccarddev = NULL; sc->domain = pci_get_domain(brdev); sc->bus.sec = pci_read_config(brdev, PCIR_SECBUS_2, 1); sc->bus.sub = pci_read_config(brdev, PCIR_SUBBUS_2, 1); sc->pribus = pcib_get_bus(parent); #if defined(NEW_PCIB) && defined(PCI_RES_BUS) pci_write_config(brdev, PCIR_PRIBUS_2, sc->pribus, 1); pcib_setup_secbus(brdev, &sc->bus, 1); #endif SLIST_INIT(&sc->rl); cbb_powerstate_d0(brdev); rid = CBBR_SOCKBASE; sc->base_res = bus_alloc_resource_any(brdev, SYS_RES_MEMORY, &rid, RF_ACTIVE); if (!sc->base_res) { device_printf(brdev, "Could not map register memory\n"); mtx_destroy(&sc->mtx); return (ENOMEM); } else { DEVPRINTF((brdev, "Found memory at %08lx\n", rman_get_start(sc->base_res))); } sc->bst = rman_get_bustag(sc->base_res); sc->bsh = rman_get_bushandle(sc->base_res); exca_init(&sc->exca[0], brdev, sc->bst, sc->bsh, CBB_EXCA_OFFSET); sc->exca[0].flags |= EXCA_HAS_MEMREG_WIN; sc->exca[0].chipset = EXCA_CARDBUS; sc->chipinit = cbb_chipinit; sc->chipinit(sc); /*Sysctls*/ sctx = device_get_sysctl_ctx(brdev); soid = device_get_sysctl_tree(brdev); SYSCTL_ADD_UINT(sctx, SYSCTL_CHILDREN(soid), OID_AUTO, "domain", CTLFLAG_RD, &sc->domain, 0, "Domain number"); SYSCTL_ADD_UINT(sctx, SYSCTL_CHILDREN(soid), OID_AUTO, "pribus", CTLFLAG_RD, &sc->pribus, 0, "Primary bus number"); SYSCTL_ADD_UINT(sctx, SYSCTL_CHILDREN(soid), OID_AUTO, "secbus", CTLFLAG_RD, &sc->bus.sec, 0, "Secondary bus number"); SYSCTL_ADD_UINT(sctx, SYSCTL_CHILDREN(soid), OID_AUTO, "subbus", CTLFLAG_RD, &sc->bus.sub, 0, "Subordinate bus number"); #if 0 SYSCTL_ADD_UINT(sctx, SYSCTL_CHILDREN(soid), OID_AUTO, "memory", CTLFLAG_RD, &sc->subbus, 0, "Memory window open"); SYSCTL_ADD_UINT(sctx, SYSCTL_CHILDREN(soid), OID_AUTO, "premem", CTLFLAG_RD, &sc->subbus, 0, "Prefetch memroy window open"); SYSCTL_ADD_UINT(sctx, SYSCTL_CHILDREN(soid), OID_AUTO, "io1", CTLFLAG_RD, &sc->subbus, 0, "io range 1 open"); SYSCTL_ADD_UINT(sctx, SYSCTL_CHILDREN(soid), OID_AUTO, "io2", CTLFLAG_RD, &sc->subbus, 0, "io range 2 open"); #endif #if !(defined(NEW_PCIB) && defined(PCI_RES_BUS)) /* * This is a gross hack. We should be scanning the entire pci * tree, assigning bus numbers in a way such that we (1) can * reserve 1 extra bus just in case and (2) all sub busses * are in an appropriate range. */ DEVPRINTF((brdev, "Secondary bus is %d\n", sc->bus.sec)); pribus = pci_read_config(brdev, PCIR_PRIBUS_2, 1); if (sc->bus.sec == 0 || sc->pribus != pribus) { if (curr_bus_number <= sc->pribus) curr_bus_number = sc->pribus + 1; if (pribus != sc->pribus) { DEVPRINTF((brdev, "Setting primary bus to %d\n", sc->pribus)); pci_write_config(brdev, PCIR_PRIBUS_2, sc->pribus, 1); } sc->bus.sec = curr_bus_number++; sc->bus.sub = curr_bus_number++; DEVPRINTF((brdev, "Secondary bus set to %d subbus %d\n", sc->bus.sec, sc->bus.sub)); pci_write_config(brdev, PCIR_SECBUS_2, sc->bus.sec, 1); pci_write_config(brdev, PCIR_SUBBUS_2, sc->bus.sub, 1); } #endif /* attach children */ sc->cbdev = device_add_child(brdev, "cardbus", -1); if (sc->cbdev == NULL) DEVPRINTF((brdev, "WARNING: cannot add cardbus bus.\n")); else if (device_probe_and_attach(sc->cbdev) != 0) DEVPRINTF((brdev, "WARNING: cannot attach cardbus bus!\n")); sc->exca[0].pccarddev = device_add_child(brdev, "pccard", -1); if (sc->exca[0].pccarddev == NULL) DEVPRINTF((brdev, "WARNING: cannot add pccard bus.\n")); else if (device_probe_and_attach(sc->exca[0].pccarddev) != 0) DEVPRINTF((brdev, "WARNING: cannot attach pccard bus.\n")); /* Map and establish the interrupt. */ rid = 0; sc->irq_res = bus_alloc_resource_any(brdev, SYS_RES_IRQ, &rid, RF_SHAREABLE | RF_ACTIVE); if (sc->irq_res == NULL) { device_printf(brdev, "Unable to map IRQ...\n"); goto err; } if (bus_setup_intr(brdev, sc->irq_res, INTR_TYPE_AV | INTR_MPSAFE, cbb_pci_filt, NULL, sc, &sc->intrhand)) { device_printf(brdev, "couldn't establish interrupt\n"); goto err; } /* reset 16-bit pcmcia bus */ exca_clrb(&sc->exca[0], EXCA_INTR, EXCA_INTR_RESET); /* turn off power */ cbb_power(brdev, CARD_OFF); /* CSC Interrupt: Card detect interrupt on */ cbb_setb(sc, CBB_SOCKET_MASK, CBB_SOCKET_MASK_CD); /* reset interrupt */ cbb_set(sc, CBB_SOCKET_EVENT, cbb_get(sc, CBB_SOCKET_EVENT)); if (bootverbose) cbb_print_config(brdev); /* Start the thread */ if (kproc_create(cbb_event_thread, sc, &sc->event_thread, 0, 0, "%s event thread", device_get_nameunit(brdev))) { device_printf(brdev, "unable to create event thread.\n"); panic("cbb_create_event_thread"); } sc->sc_root_token = root_mount_hold(device_get_nameunit(sc->dev)); return (0); err: if (sc->irq_res) bus_release_resource(brdev, SYS_RES_IRQ, 0, sc->irq_res); if (sc->base_res) { bus_release_resource(brdev, SYS_RES_MEMORY, CBBR_SOCKBASE, sc->base_res); } mtx_destroy(&sc->mtx); return (ENOMEM); } static void cbb_chipinit(struct cbb_softc *sc) { uint32_t mux, sysctrl, reg; /* Set CardBus latency timer */ if (pci_read_config(sc->dev, PCIR_SECLAT_2, 1) < 0x20) pci_write_config(sc->dev, PCIR_SECLAT_2, 0x20, 1); /* Set PCI latency timer */ if (pci_read_config(sc->dev, PCIR_LATTIMER, 1) < 0x20) pci_write_config(sc->dev, PCIR_LATTIMER, 0x20, 1); /* Restore bus configuration */ pci_write_config(sc->dev, PCIR_PRIBUS_2, sc->pribus, 1); pci_write_config(sc->dev, PCIR_SECBUS_2, sc->bus.sec, 1); pci_write_config(sc->dev, PCIR_SUBBUS_2, sc->bus.sub, 1); /* Enable DMA, memory access for this card and I/O acces for children */ pci_enable_busmaster(sc->dev); pci_enable_io(sc->dev, SYS_RES_IOPORT); pci_enable_io(sc->dev, SYS_RES_MEMORY); /* disable Legacy IO */ switch (sc->chipset) { case CB_RF5C46X: PCI_MASK_CONFIG(sc->dev, CBBR_BRIDGECTRL, & ~(CBBM_BRIDGECTRL_RL_3E0_EN | CBBM_BRIDGECTRL_RL_3E2_EN), 2); break; default: pci_write_config(sc->dev, CBBR_LEGACY, 0x0, 4); break; } /* Use PCI interrupt for interrupt routing */ PCI_MASK2_CONFIG(sc->dev, CBBR_BRIDGECTRL, & ~(CBBM_BRIDGECTRL_MASTER_ABORT | CBBM_BRIDGECTRL_INTR_IREQ_ISA_EN), | CBBM_BRIDGECTRL_WRITE_POST_EN, 2); /* * XXX this should be a function table, ala OLDCARD. This means * that we could more easily support ISA interrupts for pccard * cards if we had to. */ switch (sc->chipset) { case CB_TI113X: /* * The TI 1031, TI 1130 and TI 1131 all require another bit * be set to enable PCI routing of interrupts, and then * a bit for each of the CSC and Function interrupts we * want routed. */ PCI_MASK_CONFIG(sc->dev, CBBR_CBCTRL, | CBBM_CBCTRL_113X_PCI_INTR | CBBM_CBCTRL_113X_PCI_CSC | CBBM_CBCTRL_113X_PCI_IRQ_EN, 1); PCI_MASK_CONFIG(sc->dev, CBBR_DEVCTRL, & ~(CBBM_DEVCTRL_INT_SERIAL | CBBM_DEVCTRL_INT_PCI), 1); break; case CB_TI12XX: /* * Some TI 12xx (and [14][45]xx) based pci cards * sometimes have issues with the MFUNC register not * being initialized due to a bad EEPROM on board. * Laptops that this matters on have this register * properly initialized. * * The TI125X parts have a different register. */ mux = pci_read_config(sc->dev, CBBR_MFUNC, 4); sysctrl = pci_read_config(sc->dev, CBBR_SYSCTRL, 4); if (mux == 0) { mux = (mux & ~CBBM_MFUNC_PIN0) | CBBM_MFUNC_PIN0_INTA; if ((sysctrl & CBBM_SYSCTRL_INTRTIE) == 0) mux = (mux & ~CBBM_MFUNC_PIN1) | CBBM_MFUNC_PIN1_INTB; pci_write_config(sc->dev, CBBR_MFUNC, mux, 4); } /*FALLTHROUGH*/ case CB_TI125X: /* * Disable zoom video. Some machines initialize this * improperly and exerpience has shown that this helps * prevent strange behavior. */ pci_write_config(sc->dev, CBBR_MMCTRL, 0, 4); break; case CB_O2MICRO: /* * Issue #1: INT# generated at the same time as * selected ISA IRQ. When IREQ# or STSCHG# is active, * in addition to the ISA IRQ being generated, INT# * will also be generated at the same time. * * Some of the older controllers have an issue in * which the slot's PCI INT# will be asserted whenever * IREQ# or STSCGH# is asserted even if ExCA registers * 03h or 05h have an ISA IRQ selected. * * The fix for this issue, which will work for any * controller (old or new), is to set ExCA registers * 3Ah (slot 0) & 7Ah (slot 1) bits 7:4 = 1010b. * These bits are undocumented. By setting this * register (of each slot) to '1010xxxxb' a routing of * IREQ# to INTC# and STSCHG# to INTC# is selected. * Since INTC# isn't connected there will be no * unexpected PCI INT when IREQ# or STSCHG# is active. * However, INTA# (slot 0) or INTB# (slot 1) will * still be correctly generated if NO ISA IRQ is * selected (ExCA regs 03h or 05h are cleared). */ reg = exca_getb(&sc->exca[0], EXCA_O2MICRO_CTRL_C); reg = (reg & 0x0f) | EXCA_O2CC_IREQ_INTC | EXCA_O2CC_STSCHG_INTC; exca_putb(&sc->exca[0], EXCA_O2MICRO_CTRL_C, reg); break; case CB_TOPIC97: /* * Disable Zoom Video, ToPIC 97, 100. */ pci_write_config(sc->dev, TOPIC97_ZV_CONTROL, 0, 1); /* * ToPIC 97, 100 * At offset 0xa1: INTERRUPT CONTROL register * 0x1: Turn on INT interrupts. */ PCI_MASK_CONFIG(sc->dev, TOPIC_INTCTRL, | TOPIC97_INTCTRL_INTIRQSEL, 1); /* * ToPIC97, 100 * Need to assert support for low voltage cards */ exca_setb(&sc->exca[0], EXCA_TOPIC97_CTRL, EXCA_TOPIC97_CTRL_LV_MASK); goto topic_common; case CB_TOPIC95: /* * SOCKETCTRL appears to be TOPIC 95/B specific */ PCI_MASK_CONFIG(sc->dev, TOPIC95_SOCKETCTRL, | TOPIC95_SOCKETCTRL_SCR_IRQSEL, 4); topic_common:; /* * At offset 0xa0: SLOT CONTROL * 0x80 Enable CardBus Functionality * 0x40 Enable CardBus and PC Card registers * 0x20 Lock ID in exca regs * 0x10 Write protect ID in config regs * Clear the rest of the bits, which defaults the slot * in legacy mode to 0x3e0 and offset 0. (legacy * mode is determined elsewhere) */ pci_write_config(sc->dev, TOPIC_SLOTCTRL, TOPIC_SLOTCTRL_SLOTON | TOPIC_SLOTCTRL_SLOTEN | TOPIC_SLOTCTRL_ID_LOCK | TOPIC_SLOTCTRL_ID_WP, 1); /* * At offset 0xa3 Card Detect Control Register * 0x80 CARDBUS enbale * 0x01 Cleared for hardware change detect */ PCI_MASK2_CONFIG(sc->dev, TOPIC_CDC, | TOPIC_CDC_CARDBUS, & ~TOPIC_CDC_SWDETECT, 4); break; } /* * Need to tell ExCA registers to CSC interrupts route via PCI * interrupts. There are two ways to do this. One is to set * INTR_ENABLE and the other is to set CSC to 0. Since both * methods are mutually compatible, we do both. */ exca_putb(&sc->exca[0], EXCA_INTR, EXCA_INTR_ENABLE); exca_putb(&sc->exca[0], EXCA_CSC_INTR, 0); cbb_disable_func_intr(sc); /* close all memory and io windows */ pci_write_config(sc->dev, CBBR_MEMBASE0, 0xffffffff, 4); pci_write_config(sc->dev, CBBR_MEMLIMIT0, 0, 4); pci_write_config(sc->dev, CBBR_MEMBASE1, 0xffffffff, 4); pci_write_config(sc->dev, CBBR_MEMLIMIT1, 0, 4); pci_write_config(sc->dev, CBBR_IOBASE0, 0xffffffff, 4); pci_write_config(sc->dev, CBBR_IOLIMIT0, 0, 4); pci_write_config(sc->dev, CBBR_IOBASE1, 0xffffffff, 4); pci_write_config(sc->dev, CBBR_IOLIMIT1, 0, 4); } static int cbb_route_interrupt(device_t pcib, device_t dev, int pin) { struct cbb_softc *sc = (struct cbb_softc *)device_get_softc(pcib); return (rman_get_start(sc->irq_res)); } static int cbb_pci_shutdown(device_t brdev) { struct cbb_softc *sc = (struct cbb_softc *)device_get_softc(brdev); /* * We're about to pull the rug out from the card, so mark it as * gone to prevent harm. */ sc->cardok = 0; /* * Place the cards in reset, turn off the interrupts and power * down the socket. */ PCI_MASK_CONFIG(brdev, CBBR_BRIDGECTRL, |CBBM_BRIDGECTRL_RESET, 2); exca_clrb(&sc->exca[0], EXCA_INTR, EXCA_INTR_RESET); cbb_set(sc, CBB_SOCKET_MASK, 0); cbb_set(sc, CBB_SOCKET_EVENT, 0xffffffff); cbb_power(brdev, CARD_OFF); /* * For paranoia, turn off all address decoding. Really not needed, * it seems, but it can't hurt */ exca_putb(&sc->exca[0], EXCA_ADDRWIN_ENABLE, 0); pci_write_config(brdev, CBBR_MEMBASE0, 0, 4); pci_write_config(brdev, CBBR_MEMLIMIT0, 0, 4); pci_write_config(brdev, CBBR_MEMBASE1, 0, 4); pci_write_config(brdev, CBBR_MEMLIMIT1, 0, 4); pci_write_config(brdev, CBBR_IOBASE0, 0, 4); pci_write_config(brdev, CBBR_IOLIMIT0, 0, 4); pci_write_config(brdev, CBBR_IOBASE1, 0, 4); pci_write_config(brdev, CBBR_IOLIMIT1, 0, 4); return (0); } static int cbb_pci_filt(void *arg) { struct cbb_softc *sc = arg; uint32_t sockevent; uint8_t csc; int retval = FILTER_STRAY; /* * Some chips also require us to read the old ExCA registe for card * status change when we route CSC vis PCI. This isn't supposed to be * required, but it clears the interrupt state on some chipsets. * Maybe there's a setting that would obviate its need. Maybe we * should test the status bits and deal with them, but so far we've * not found any machines that don't also give us the socket status * indication above. * * This call used to be unconditional. However, further research * suggests that we hit this condition when the card READY interrupt * fired. So now we only read it for 16-bit cards, and we only claim * the interrupt if READY is set. If this still causes problems, then * the next step would be to read this if we have a 16-bit card *OR* * we have no card. We treat the READY signal as if it were the power * completion signal. Some bridges may double signal things here, bit * signalling twice should be OK since we only sleep on the powerintr * in one place and a double wakeup would be benign there. */ if (sc->flags & CBB_16BIT_CARD) { csc = exca_getb(&sc->exca[0], EXCA_CSC); if (csc & EXCA_CSC_READY) { atomic_add_int(&sc->powerintr, 1); wakeup((void *)&sc->powerintr); retval = FILTER_HANDLED; } } /* * Read the socket event. Sometimes, the theory goes, the PCI bus is * so loaded that it cannot satisfy the read request, so we get * garbage back from the following read. We have to filter out the * garbage so that we don't spontaneously reset the card under high * load. PCI isn't supposed to act like this. No doubt this is a bug * in the PCI bridge chipset (or cbb brige) that's being used in * certain amd64 laptops today. Work around the issue by assuming * that any bits we don't know about being set means that we got * garbage. */ sockevent = cbb_get(sc, CBB_SOCKET_EVENT); if (sockevent != 0 && (sockevent & ~CBB_SOCKET_EVENT_VALID_MASK) == 0) { /* * If anything has happened to the socket, we assume that the * card is no longer OK, and we shouldn't call its ISR. We * set cardok as soon as we've attached the card. This helps * in a noisy eject, which happens all too often when users * are ejecting their PC Cards. * * We use this method in preference to checking to see if the * card is still there because the check suffers from a race * condition in the bouncing case. */ #define DELTA (CBB_SOCKET_MASK_CD) if (sockevent & DELTA) { cbb_clrb(sc, CBB_SOCKET_MASK, DELTA); cbb_set(sc, CBB_SOCKET_EVENT, DELTA); sc->cardok = 0; cbb_disable_func_intr(sc); wakeup(&sc->intrhand); } #undef DELTA /* * Wakeup anybody waiting for a power interrupt. We have to * use atomic_add_int for wakups on other cores. */ if (sockevent & CBB_SOCKET_EVENT_POWER) { cbb_clrb(sc, CBB_SOCKET_MASK, CBB_SOCKET_EVENT_POWER); cbb_set(sc, CBB_SOCKET_EVENT, CBB_SOCKET_EVENT_POWER); atomic_add_int(&sc->powerintr, 1); wakeup((void *)&sc->powerintr); } /* * Status change interrupts aren't presently used in the * rest of the driver. For now, just ACK them. */ if (sockevent & CBB_SOCKET_EVENT_CSTS) cbb_set(sc, CBB_SOCKET_EVENT, CBB_SOCKET_EVENT_CSTS); retval = FILTER_HANDLED; } return retval; } #if defined(NEW_PCIB) && defined(PCI_RES_BUS) static struct resource * cbb_pci_alloc_resource(device_t bus, device_t child, int type, int *rid, u_long start, u_long end, u_long count, u_int flags) { struct cbb_softc *sc; sc = device_get_softc(bus); if (type == PCI_RES_BUS) return (pcib_alloc_subbus(&sc->bus, child, rid, start, end, count, flags)); return (cbb_alloc_resource(bus, child, type, rid, start, end, count, flags)); } static int cbb_pci_adjust_resource(device_t bus, device_t child, int type, struct resource *r, u_long start, u_long end) { struct cbb_softc *sc; sc = device_get_softc(bus); if (type == PCI_RES_BUS) { if (!rman_is_region_manager(r, &sc->bus.rman)) return (EINVAL); return (rman_adjust_resource(r, start, end)); } return (bus_generic_adjust_resource(bus, child, type, r, start, end)); } static int cbb_pci_release_resource(device_t bus, device_t child, int type, int rid, struct resource *r) { struct cbb_softc *sc; int error; sc = device_get_softc(bus); if (type == PCI_RES_BUS) { if (!rman_is_region_manager(r, &sc->bus.rman)) return (EINVAL); if (rman_get_flags(r) & RF_ACTIVE) { error = bus_deactivate_resource(child, type, rid, r); if (error) return (error); } return (rman_release_resource(r)); } return (cbb_release_resource(bus, child, type, rid, r)); } #endif /************************************************************************/ /* PCI compat methods */ /************************************************************************/ static int cbb_maxslots(device_t brdev) { return (0); } static uint32_t cbb_read_config(device_t brdev, u_int b, u_int s, u_int f, u_int reg, int width) { /* * Pass through to the next ppb up the chain (i.e. our grandparent). */ return (PCIB_READ_CONFIG(device_get_parent(device_get_parent(brdev)), b, s, f, reg, width)); } static void cbb_write_config(device_t brdev, u_int b, u_int s, u_int f, u_int reg, uint32_t val, int width) { /* * Pass through to the next ppb up the chain (i.e. our grandparent). */ PCIB_WRITE_CONFIG(device_get_parent(device_get_parent(brdev)), b, s, f, reg, val, width); } static int cbb_pci_suspend(device_t brdev) { int error = 0; struct cbb_softc *sc = device_get_softc(brdev); error = bus_generic_suspend(brdev); if (error != 0) return (error); cbb_set(sc, CBB_SOCKET_MASK, 0); /* Quiet hardware */ sc->cardok = 0; /* Card is bogus now */ return (0); } static int cbb_pci_resume(device_t brdev) { int error = 0; struct cbb_softc *sc = (struct cbb_softc *)device_get_softc(brdev); uint32_t tmp; /* * In the APM and early ACPI era, BIOSes saved the PCI config * registers. As chips became more complicated, that functionality moved * into the ACPI code / tables. We must therefore, restore the settings * we made here to make sure the device come back. Transitions to Dx * from D0 and back to D0 cause the bridge to lose its config space, so * all the bus mappings and such are preserved. * * For most drivers, the PCI layer handles this saving. However, since * there's much black magic and arcane art hidden in these few lines of * code that would be difficult to transition into the PCI * layer. chipinit was several years of trial and error to write. */ pci_write_config(brdev, CBBR_SOCKBASE, rman_get_start(sc->base_res), 4); DEVPRINTF((brdev, "PCI Memory allocated: %08lx\n", rman_get_start(sc->base_res))); sc->chipinit(sc); /* reset interrupt -- Do we really need to do this? */ tmp = cbb_get(sc, CBB_SOCKET_EVENT); cbb_set(sc, CBB_SOCKET_EVENT, tmp); /* CSC Interrupt: Card detect interrupt on */ cbb_setb(sc, CBB_SOCKET_MASK, CBB_SOCKET_MASK_CD); /* Signal the thread to wakeup. */ wakeup(&sc->intrhand); error = bus_generic_resume(brdev); return (error); } static device_method_t cbb_methods[] = { /* Device interface */ DEVMETHOD(device_probe, cbb_pci_probe), DEVMETHOD(device_attach, cbb_pci_attach), DEVMETHOD(device_detach, cbb_detach), DEVMETHOD(device_shutdown, cbb_pci_shutdown), DEVMETHOD(device_suspend, cbb_pci_suspend), DEVMETHOD(device_resume, cbb_pci_resume), /* bus methods */ DEVMETHOD(bus_read_ivar, cbb_read_ivar), DEVMETHOD(bus_write_ivar, cbb_write_ivar), #if defined(NEW_PCIB) && defined(PCI_RES_BUS) DEVMETHOD(bus_alloc_resource, cbb_pci_alloc_resource), DEVMETHOD(bus_adjust_resource, cbb_pci_adjust_resource), DEVMETHOD(bus_release_resource, cbb_pci_release_resource), #else DEVMETHOD(bus_alloc_resource, cbb_alloc_resource), DEVMETHOD(bus_release_resource, cbb_release_resource), #endif DEVMETHOD(bus_activate_resource, cbb_activate_resource), DEVMETHOD(bus_deactivate_resource, cbb_deactivate_resource), DEVMETHOD(bus_driver_added, cbb_driver_added), DEVMETHOD(bus_child_detached, cbb_child_detached), DEVMETHOD(bus_setup_intr, cbb_setup_intr), DEVMETHOD(bus_teardown_intr, cbb_teardown_intr), DEVMETHOD(bus_child_present, cbb_child_present), /* 16-bit card interface */ DEVMETHOD(card_set_res_flags, cbb_pcic_set_res_flags), DEVMETHOD(card_set_memory_offset, cbb_pcic_set_memory_offset), /* power interface */ DEVMETHOD(power_enable_socket, cbb_power_enable_socket), DEVMETHOD(power_disable_socket, cbb_power_disable_socket), /* pcib compatibility interface */ DEVMETHOD(pcib_maxslots, cbb_maxslots), DEVMETHOD(pcib_read_config, cbb_read_config), DEVMETHOD(pcib_write_config, cbb_write_config), DEVMETHOD(pcib_route_interrupt, cbb_route_interrupt), DEVMETHOD_END }; static driver_t cbb_driver = { "cbb", cbb_methods, sizeof(struct cbb_softc) }; DRIVER_MODULE(cbb, pci, cbb_driver, cbb_devclass, 0, 0); MODULE_DEPEND(cbb, exca, 1, 1, 1);