FreeBSD Driver for 10 Gigabit PCI Express Server Adapters ============================================= /*$FreeBSD$*/ May 14, 2008 Contents ======== - Overview - Supported Adapters - Building and Installation - Additional Configurations - Known Limitations Overview ======== This file describes the FreeBSD* driver for the 10 Gigabit PCIE Family of Adapters. Drivers has been developed for use with FreeBSD 7 or later. For questions related to hardware requirements, refer to the documentation supplied with your Intel 10GbE adapter. All hardware requirements listed apply to use with FreeBSD. Supported Adapters ================== The following Intel network adapters are compatible with the drivers in this release: Controller Adapter Name Physical Layer ---------- ------------ -------------- 82598EB Intel(R) 10 Gigabit XF SR/AF 10G Base -LR (850 nm optical fiber) Dual Port Server Adapter 10G Base -SR (1310 nm optical fiber) 82598EB Intel(R) 10 Gigabit XF SR/LR Server Adapter Intel(R) 82598EB 10 Gigabit AF Network Connection Intel(R) 82598EB 10 Gigabit AT CX4 Network Connection Building and Installation ========================= NOTE: You must have kernel sources installed in order to compile the driver module. In the instructions below, x.x.x is the driver version as indicated in the name of the driver tar. 1. Move the base driver tar file to the directory of your choice. For example, use /home/username/ixgbe or /usr/local/src/ixgbe. 2. Untar/unzip the archive: tar xfz ixgbe-x.x.x.tar.gz 3. To install man page: cd ixgbe-x.x.x gzip -c ixgbe.4 > /usr/share/man/man4/ixgbee.4.gz 4. To load the driver onto a running system: cd ixgbe-x.x.x/src make load 5. To assign an IP address to the interface, enter the following: ifconfig ix 6. Verify that the interface works. Enter the following, where is the IP address for another machine on the same subnet as the interface that is being tested: ping 7. If you want the driver to load automatically when the system is booted: cd ixgbe-x.x.x/src make make install Edit /boot/loader.conf, and add the following line: ixgbe_load="YES" OR compile the driver into the kernel (see item 8). Edit /etc/rc.conf, and create the appropriate ifconfig_ixgbe entry: ifconfig_ix="" Example usage: ifconfig_ix0="inet 192.168.10.1 netmask 255.255.255.0" NOTE: For assistance, see the ifconfig man page. 8. If you want to compile the driver into the kernel, enter: FreeBSD 7 or later: cd ixgbe-x.x.x/src cp *.[ch] /usr/src/sys/dev/ixgbe cp Makefile.kernel /usr/src/sys/modules/ixgbe/Makefile Edit the kernel configuration file (i.e., GENERIC or MYKERNEL) in /usr/src/sys/i386/conf (replace "i386" with the appropriate system architecture if necessary), and ensure the following line is present: device ixgbe Compile and install the kernel. The system must be reboot for the kernel updates to take affect. For additional information on compiling the kernel, consult the FreeBSD operating system documentation. Configuration and Tuning ========================= The driver supports Transmit/Receive Checksum Offload and Jumbo Frames on all 10 Gigabit adapters. Jumbo Frames ------------ To enable Jumbo Frames, use the ifconfig utility to increase the MTU beyond 1500 bytes. NOTES: - The Jumbo Frames setting on the switch must be set to at least 22 bytes larger than that of the adapter. - There are known performance issues with this driver when running UDP traffic with Jumbo Frames. The Jumbo Frames MTU range for Intel Adapters is 1500 to 16114. The default MTU range is 1500. To modify the setting, enter the following: ifconfig ix mtu 9000 To confirm an interface's MTU value, use the ifconfig command. To confirm the MTU used between two specific devices, use: route get VLANs ----- To create a new VLAN pseudo-interface: ifconfig create To associate the VLAN pseudo-interface with a physical interface and assign a VLAN ID, IP address, and netmask: ifconfig netmask vlan vlandev Example: ifconfig vlan10 10.0.0.1 netmask 255.255.255.0 vlan 10 vlandev ixgbe0 In this example, all packets will be marked on egress with 802.1Q VLAN tags, specifying a VLAN ID of 10. To remove a VLAN pseudo-interface: ifconfig destroy Checksum Offload ---------------- Checksum offloading supports both TCP and UDP packets and is supported for both transmit and receive. Checksum offloading can be enabled or disabled using ifconfig. Both transmit and receive offloading will be either enabled or disabled together. You cannot enable/disable one without the other. To enable checksum offloading: ifconfig rxcsum To disable checksum offloading: ifconfig -rxcsum To confirm the current setting: ifconfig TSO --- To disable: ifconfig -tso To re-enable: ifconfig tso LRO ___ Large Receive Offload is available in version 1.4.4, it is on by default. It can be toggled off and on by using: sysctl dev.ix.X.enable_lro=[0,1] NOTE: when changing this feature you MUST be sure the interface is reinitialized, it is easy to do this with ifconfig down/up. The LRO code will ultimately move into the kernel stack code, but for this first release it was included with the driver. Important system configuration changes: --------------------------------------- When there is a choice run on a 64bit OS rather than 32, it makes a significant difference in improvement. The default scheduler SCHED_4BSD is not smart about SMP locality issues. Significant improvement can be achieved by switching to the ULE scheduler. This is done by changing the entry in the config file from SCHED_4BSD to SCHED_ULE. Note that this is only advisable on FreeBSD 7, on 6.X there have been stability problems with ULE. Change the file /etc/sysctl.conf, add the line: hw.intr_storm_threshold: 8000 (the default is 1000) Best throughput results are seen with a large MTU; use 9000 if possible. The default number of descriptors is 256, increasing this to 1024 or even 2048 may improve performance. Known Limitations ================= Under small packets UDP stress test with 10GbE driver, the FreeBSD system will drop UDP packets due to the fullness of socket buffers. You may want to change the driver's Flow Control variables to the minimum value for controlling packet reception. Support ======= For general information and support, go to the Intel support website at: http://support.intel.com If an issue is identified with the released source code on the supported kernel with a supported adapter, email the specific information related to the issue to freebsd@intel.com. License ======= This software program is released under the terms of a license agreement between you ('Licensee') and Intel. Do not use or load this software or any associated materials (collectively, the 'Software') until you have carefully read the full terms and conditions of the LICENSE located in this software package. By loading or using the Software, you agree to the terms of this Agreement. If you do not agree with the terms of this Agreement, do not install or use the Software. * Other names and brands may be claimed as the property of others.