2 * refclock_wwvb - clock driver for Spectracom WWVB and GPS receivers
9 #if defined(REFCLOCK) && defined(CLOCK_SPECTRACOM)
13 #include "ntp_refclock.h"
14 #include "ntp_calendar.h"
15 #include "ntp_stdlib.h"
21 #include "ppsapi_timepps.h"
22 #include "refclock_atom.h"
23 #endif /* HAVE_PPSAPI */
26 * This driver supports the Spectracom Model 8170 and Netclock/2 WWVB
27 * Synchronized Clocks and the Netclock/GPS Master Clock. Both the WWVB
28 * and GPS clocks have proven reliable sources of time; however, the
29 * WWVB clocks have proven vulnerable to high ambient conductive RF
30 * interference. The claimed accuracy of the WWVB clocks is 100 us
31 * relative to the broadcast signal, while the claimed accuracy of the
32 * GPS clock is 50 ns; however, in most cases the actual accuracy is
33 * limited by the resolution of the timecode and the latencies of the
34 * serial interface and operating system.
36 * The WWVB and GPS clocks should be configured for 24-hour display,
37 * AUTO DST off, time zone 0 (UTC), data format 0 or 2 (see below) and
38 * baud rate 9600. If the clock is to used as the source for the IRIG
39 * Audio Decoder (refclock_irig.c in this distribution), it should be
40 * configured for AM IRIG output and IRIG format 1 (IRIG B with
41 * signature control). The GPS clock can be configured either to respond
42 * to a 'T' poll character or left running continuously.
44 * There are two timecode formats used by these clocks. Format 0, which
45 * is available with both the Netclock/2 and 8170, and format 2, which
46 * is available only with the Netclock/2, specially modified 8170 and
49 * Format 0 (22 ASCII printing characters):
51 * <cr><lf>i ddd hh:mm:ss TZ=zz<cr><lf>
53 * on-time = first <cr>
54 * hh:mm:ss = hours, minutes, seconds
55 * i = synchronization flag (' ' = in synch, '?' = out of synch)
57 * The alarm condition is indicated by other than ' ' at i, which occurs
58 * during initial synchronization and when received signal is lost for
61 * Format 2 (24 ASCII printing characters):
63 * <cr><lf>iqyy ddd hh:mm:ss.fff ld
66 * i = synchronization flag (' ' = in synch, '?' = out of synch)
67 * q = quality indicator (' ' = locked, 'A'...'D' = unlocked)
68 * yy = year (as broadcast)
70 * hh:mm:ss.fff = hours, minutes, seconds, milliseconds
72 * The alarm condition is indicated by other than ' ' at i, which occurs
73 * during initial synchronization and when received signal is lost for
74 * about ten hours. The unlock condition is indicated by other than ' '
77 * The q is normally ' ' when the time error is less than 1 ms and a
78 * character in the set 'A'...'D' when the time error is less than 10,
79 * 100, 500 and greater than 500 ms respectively. The l is normally ' ',
80 * but is set to 'L' early in the month of an upcoming UTC leap second
81 * and reset to ' ' on the first day of the following month. The d is
82 * set to 'S' for standard time 'I' on the day preceding a switch to
83 * daylight time, 'D' for daylight time and 'O' on the day preceding a
84 * switch to standard time. The start bit of the first <cr> is
85 * synchronized to the indicated time as returned.
87 * This driver does not need to be told which format is in use - it
88 * figures out which one from the length of the message. The driver
89 * makes no attempt to correct for the intrinsic jitter of the radio
90 * itself, which is a known problem with the older radios.
92 * PPS Signal Processing
94 * When PPS signal processing is enabled, and when the system clock has
95 * been set by this or another driver and the PPS signal offset is
96 * within 0.4 s of the system clock offset, the PPS signal replaces the
97 * timecode for as long as the PPS signal is active. If for some reason
98 * the PPS signal fails for one or more poll intervals, the driver
99 * reverts to the timecode. If the timecode fails for one or more poll
100 * intervals, the PPS signal is disconnected.
104 * This driver can retrieve a table of quality data maintained
105 * internally by the Netclock/2 clock. If flag4 of the fudge
106 * configuration command is set to 1, the driver will retrieve this
107 * table and write it to the clockstats file when the first timecode
108 * message of a new day is received.
110 * PPS calibration fudge time 1: format 0 .003134, format 2 .004034
113 * Interface definitions
115 #define DEVICE "/dev/wwvb%d" /* device name and unit */
116 #define SPEED232 B9600 /* uart speed (9600 baud) */
117 #define PRECISION (-13) /* precision assumed (about 100 us) */
118 #define PPS_PRECISION (-13) /* precision assumed (about 100 us) */
119 #define REFID "WWVB" /* reference ID */
120 #define DESCRIPTION "Spectracom WWVB/GPS Receiver" /* WRU */
122 #define LENWWVB0 22 /* format 0 timecode length */
123 #define LENWWVB2 24 /* format 2 timecode length */
124 #define LENWWVB3 29 /* format 3 timecode length */
125 #define MONLIN 15 /* number of monitoring lines */
128 * WWVB unit control structure
132 struct refclock_atom atom; /* PPSAPI structure */
133 int ppsapi_tried; /* attempt PPSAPI once */
134 int ppsapi_lit; /* time_pps_create() worked */
135 int tcount; /* timecode sample counter */
136 int pcount; /* PPS sample counter */
137 #endif /* HAVE_PPSAPI */
138 l_fp laststamp; /* last <CR> timestamp */
139 int prev_eol_cr; /* was last EOL <CR> (not <LF>)? */
140 u_char lasthour; /* last hour (for monitor) */
141 u_char linect; /* count ignored lines (for monitor */
145 * Function prototypes
147 static int wwvb_start (int, struct peer *);
148 static void wwvb_shutdown (int, struct peer *);
149 static void wwvb_receive (struct recvbuf *);
150 static void wwvb_poll (int, struct peer *);
151 static void wwvb_timer (int, struct peer *);
153 static void wwvb_control (int, const struct refclockstat *,
154 struct refclockstat *, struct peer *);
155 #define WWVB_CONTROL wwvb_control
157 #define WWVB_CONTROL noentry
158 #endif /* HAVE_PPSAPI */
163 struct refclock refclock_wwvb = {
164 wwvb_start, /* start up driver */
165 wwvb_shutdown, /* shut down driver */
166 wwvb_poll, /* transmit poll message */
167 WWVB_CONTROL, /* fudge set/change notification */
168 noentry, /* initialize driver (not used) */
169 noentry, /* not used (old wwvb_buginfo) */
170 wwvb_timer /* called once per second */
175 * wwvb_start - open the devices and initialize data for processing
183 register struct wwvbunit *up;
184 struct refclockproc *pp;
189 * Open serial port. Use CLK line discipline, if available.
191 snprintf(device, sizeof(device), DEVICE, unit);
192 fd = refclock_open(device, SPEED232, LDISC_CLK);
197 * Allocate and initialize unit structure
199 up = emalloc_zero(sizeof(*up));
201 pp->io.clock_recv = wwvb_receive;
202 pp->io.srcclock = peer;
205 if (!io_addclock(&pp->io)) {
214 * Initialize miscellaneous variables
216 peer->precision = PRECISION;
217 pp->clockdesc = DESCRIPTION;
218 memcpy(&pp->refid, REFID, 4);
224 * wwvb_shutdown - shut down the clock
232 struct refclockproc * pp;
233 struct wwvbunit * up;
238 io_closeclock(&pp->io);
245 * wwvb_receive - receive data from the serial interface
249 struct recvbuf *rbufp
253 struct refclockproc *pp;
256 l_fp trtmp; /* arrival timestamp */
257 int tz; /* time zone */
258 int day, month; /* ddd conversion */
259 int temp; /* int temp */
260 char syncchar; /* synchronization indicator */
261 char qualchar; /* quality indicator */
262 char leapchar; /* leap indicator */
263 char dstchar; /* daylight/standard indicator */
264 char tmpchar; /* trashbin */
267 * Initialize pointers and read the timecode and timestamp
269 peer = rbufp->recv_peer;
272 temp = refclock_gtlin(rbufp, pp->a_lastcode, BMAX, &trtmp);
275 * Note we get a buffer and timestamp for both a <cr> and <lf>,
276 * but only the <cr> timestamp is retained. Note: in format 0 on
277 * a Netclock/2 or upgraded 8170 the start bit is delayed 100
278 * +-50 us relative to the pps; however, on an unmodified 8170
279 * the start bit can be delayed up to 10 ms. In format 2 the
280 * reading precision is only to the millisecond. Thus, unless
281 * you have a PPS gadget and don't have to have the year, format
282 * 0 provides the lowest jitter.
283 * Save the timestamp of each <CR> in up->laststamp. Lines with
284 * no characters occur for every <LF>, and for some <CR>s when
285 * format 0 is used. Format 0 starts and ends each cycle with a
286 * <CR><LF> pair, format 2 starts each cycle with its only pair.
287 * The preceding <CR> is the on-time character for both formats.
288 * The timestamp provided with non-empty lines corresponds to
289 * the <CR> following the timecode, which is ultimately not used
290 * with format 0 and is used for the following timecode for
294 if (up->prev_eol_cr) {
295 DPRINTF(2, ("wwvb: <LF> @ %s\n",
296 prettydate(&trtmp)));
298 up->laststamp = trtmp;
299 DPRINTF(2, ("wwvb: <CR> @ %s\n",
300 prettydate(&trtmp)));
302 up->prev_eol_cr = !up->prev_eol_cr;
306 pp->lastrec = up->laststamp;
307 up->laststamp = trtmp;
308 up->prev_eol_cr = TRUE;
309 DPRINTF(2, ("wwvb: code @ %s\n"
310 " using %s minus one char\n",
311 prettydate(&trtmp), prettydate(&pp->lastrec)));
312 if (L_ISZERO(&pp->lastrec))
316 * We get down to business, check the timecode format and decode
317 * its contents. This code uses the timecode length to determine
318 * format 0, 2 or 3. If the timecode has invalid length or is
319 * not in proper format, we declare bad format and exit.
321 syncchar = qualchar = leapchar = dstchar = ' ';
323 switch (pp->lencode) {
328 * Timecode format 0: "I ddd hh:mm:ss DTZ=nn"
330 if (sscanf(pp->a_lastcode,
331 "%c %3d %2d:%2d:%2d%c%cTZ=%2d",
332 &syncchar, &pp->day, &pp->hour, &pp->minute,
333 &pp->second, &tmpchar, &dstchar, &tz) == 8) {
342 * Timecode format 2: "IQyy ddd hh:mm:ss.mmm LD" */
343 if (sscanf(pp->a_lastcode,
344 "%c%c %2d %3d %2d:%2d:%2d.%3ld %c",
345 &syncchar, &qualchar, &pp->year, &pp->day,
346 &pp->hour, &pp->minute, &pp->second, &pp->nsec,
356 * Timecode format 3: "0003I yyyymmdd hhmmss+0000SL#"
357 * WARNING: Undocumented, and the on-time character # is
358 * not yet handled correctly by this driver. It may be
359 * as simple as compensating for an additional 1/960 s.
361 if (sscanf(pp->a_lastcode,
362 "0003%c %4d%2d%2d %2d%2d%2d+0000%c%c",
363 &syncchar, &pp->year, &month, &day, &pp->hour,
364 &pp->minute, &pp->second, &dstchar, &leapchar) == 8)
366 pp->day = ymd2yd(pp->year, month, day);
376 * Unknown format: If dumping internal table, record
377 * stats; otherwise, declare bad format.
379 if (up->linect > 0) {
381 record_clock_stats(&peer->srcadr,
384 refclock_report(peer, CEVNT_BADREPLY);
390 * Decode synchronization, quality and leap characters. If
391 * unsynchronized, set the leap bits accordingly and exit.
392 * Otherwise, set the leap bits according to the leap character.
393 * Once synchronized, the dispersion depends only on the
400 pp->lastref = pp->lastrec;
416 pp->disp = MAXDISPERSE;
420 pp->disp = MAXDISPERSE;
421 refclock_report(peer, CEVNT_BADREPLY);
425 pp->leap = LEAP_NOTINSYNC;
426 else if (leapchar == 'L')
427 pp->leap = LEAP_ADDSECOND;
429 pp->leap = LEAP_NOWARNING;
432 * Process the new sample in the median filter and determine the
433 * timecode timestamp, but only if the PPS is not in control.
437 if (peer->flags & FLAG_PPS)
440 #endif /* HAVE_PPSAPI */
441 if (!refclock_process_f(pp, pp->fudgetime2))
442 refclock_report(peer, CEVNT_BADTIME);
447 * wwvb_timer - called once per second by the transmit procedure
455 register struct wwvbunit *up;
456 struct refclockproc *pp;
457 char pollchar; /* character sent to clock */
463 * Time to poll the clock. The Spectracom clock responds to a
464 * 'T' by returning a timecode in the format(s) specified above.
465 * Note there is no checking on state, since this may not be the
466 * only customer reading the clock. Only one customer need poll
467 * the clock; all others just listen in.
475 if (write(pp->io.fd, &pollchar, 1) != 1)
476 refclock_report(peer, CEVNT_FAULT);
480 printf("%c poll at %s\n", pollchar, prettydate(&now));
483 if (up->ppsapi_lit &&
484 refclock_pps(peer, &up->atom, pp->sloppyclockflag) > 0) {
486 peer->flags |= FLAG_PPS;
487 peer->precision = PPS_PRECISION;
489 #endif /* HAVE_PPSAPI */
494 * wwvb_poll - called by the transmit procedure
502 register struct wwvbunit *up;
503 struct refclockproc *pp;
506 * Sweep up the samples received since the last poll. If none
507 * are received, declare a timeout and keep going.
514 * If the monitor flag is set (flag4), we dump the internal
515 * quality table at the first timecode beginning the day.
517 if (pp->sloppyclockflag & CLK_FLAG4 && pp->hour <
520 up->lasthour = (u_char)pp->hour;
523 * Process median filter samples. If none received, declare a
524 * timeout and keep going.
527 if (up->pcount == 0) {
528 peer->flags &= ~FLAG_PPS;
529 peer->precision = PRECISION;
531 if (up->tcount == 0) {
532 pp->coderecv = pp->codeproc;
533 refclock_report(peer, CEVNT_TIMEOUT);
536 up->pcount = up->tcount = 0;
537 #else /* HAVE_PPSAPI */
538 if (pp->coderecv == pp->codeproc) {
539 refclock_report(peer, CEVNT_TIMEOUT);
542 #endif /* HAVE_PPSAPI */
543 refclock_receive(peer);
544 record_clock_stats(&peer->srcadr, pp->a_lastcode);
547 printf("wwvb: timecode %d %s\n", pp->lencode,
554 * wwvb_control - fudge parameters have been set or changed
560 const struct refclockstat *in_st,
561 struct refclockstat *out_st,
565 register struct wwvbunit *up;
566 struct refclockproc *pp;
571 if (!(pp->sloppyclockflag & CLK_FLAG1)) {
572 if (!up->ppsapi_tried)
574 up->ppsapi_tried = 0;
577 peer->flags &= ~FLAG_PPS;
578 peer->precision = PRECISION;
579 time_pps_destroy(up->atom.handle);
585 if (up->ppsapi_tried)
588 * Light up the PPSAPI interface.
590 up->ppsapi_tried = 1;
591 if (refclock_ppsapi(pp->io.fd, &up->atom)) {
596 msyslog(LOG_WARNING, "%s flag1 1 but PPSAPI fails",
597 refnumtoa(&peer->srcadr));
599 #endif /* HAVE_PPSAPI */
602 int refclock_wwvb_bs;
603 #endif /* REFCLOCK */