3 # On the handling of kernel options
5 # All kernel options should be listed in NOTES, with suitable
6 # descriptions. Negative options (options that make some code not
7 # compile) should be commented out; LINT (generated from NOTES) should
8 # compile as much code as possible. Try to structure option-using
9 # code so that a single option only switch code on, or only switch
10 # code off, to make it possible to have a full compile-test. If
11 # necessary, you can check for COMPILING_LINT to get maximum code
14 # All new options shall also be listed in either "conf/options" or
15 # "conf/options.<machine>". Options that affect a single source-file
16 # <xxx>.[c|s] should be directed into "opt_<xxx>.h", while options
17 # that affect multiple files should either go in "opt_global.h" if
18 # this is a kernel-wide option (used just about everywhere), or in
19 # "opt_<option-name-in-lower-case>.h" if it affects only some files.
20 # Note that the effect of listing only an option without a
21 # header-file-name in conf/options (and cousins) is that the last
22 # convention is followed.
24 # This handling scheme is not yet fully implemented.
27 # Format of this file:
28 # Option name filename
30 # If filename is missing, the default is
31 # opt_<name-of-option-in-lower-case>.h
34 AACRAID_DEBUG opt_aacraid.h
35 AHC_ALLOW_MEMIO opt_aic7xxx.h
36 AHC_TMODE_ENABLE opt_aic7xxx.h
37 AHC_DUMP_EEPROM opt_aic7xxx.h
38 AHC_DEBUG opt_aic7xxx.h
39 AHC_DEBUG_OPTS opt_aic7xxx.h
40 AHC_REG_PRETTY_PRINT opt_aic7xxx.h
41 AHD_DEBUG opt_aic79xx.h
42 AHD_DEBUG_OPTS opt_aic79xx.h
43 AHD_TMODE_ENABLE opt_aic79xx.h
44 AHD_REG_PRETTY_PRINT opt_aic79xx.h
45 ADW_ALLOW_MEMIO opt_adw.h
48 TWA_FLASH_FIRMWARE opt_twa.h
51 ALT_BREAK_TO_DEBUGGER opt_kdb.h
52 BREAK_TO_DEBUGGER opt_kdb.h
54 DDB_BUFR_SIZE opt_ddb.h
55 DDB_CAPTURE_DEFAULTBUFSIZE opt_ddb.h
56 DDB_CAPTURE_MAXBUFSIZE opt_ddb.h
62 KDB_UNATTENDED opt_kdb.h
64 SYSCTL_DEBUG opt_sysctl.h
65 EARLY_PRINTF opt_global.h
66 TEXTDUMP_PREFERRED opt_ddb.h
67 TEXTDUMP_VERBOSE opt_ddb.h
69 # Miscellaneous options.
72 ALTERA_SDCARD_FAST_SIM opt_altera_sdcard.h
73 ATSE_CFI_HACK opt_cfi.h
75 BOOTHOWTO opt_global.h
76 BOOTVERBOSE opt_global.h
78 CAPABILITIES opt_capsicum.h
79 CAPABILITY_MODE opt_capsicum.h
80 COMPAT_43 opt_compat.h
81 COMPAT_43TTY opt_compat.h
82 COMPAT_FREEBSD4 opt_compat.h
83 COMPAT_FREEBSD5 opt_compat.h
84 COMPAT_FREEBSD6 opt_compat.h
85 COMPAT_FREEBSD7 opt_compat.h
86 COMPAT_LINUXKPI opt_compat.h
87 COMPILING_LINT opt_global.h
88 COMPRESS_USER_CORES opt_core.h
90 DEADLKRES opt_watchdog.h
94 FULL_PREEMPTION opt_sched.h
95 IPI_PREEMPTION opt_sched.h
100 GEOM_CONCAT opt_geom.h
104 GEOM_JOURNAL opt_geom.h
105 GEOM_LABEL opt_geom.h
106 GEOM_LINUX_LVM opt_geom.h
109 GEOM_MIRROR opt_geom.h
110 GEOM_MOUNTVER opt_geom.h
111 GEOM_MULTIPATH opt_geom.h
113 GEOM_PART_APM opt_geom.h
114 GEOM_PART_BSD opt_geom.h
115 GEOM_PART_BSD64 opt_geom.h
116 GEOM_PART_EBR opt_geom.h
117 GEOM_PART_EBR_COMPAT opt_geom.h
118 GEOM_PART_GPT opt_geom.h
119 GEOM_PART_LDM opt_geom.h
120 GEOM_PART_MBR opt_geom.h
121 GEOM_PART_PC98 opt_geom.h
122 GEOM_PART_VTOC8 opt_geom.h
125 GEOM_RAID3 opt_geom.h
126 GEOM_SHSEC opt_geom.h
127 GEOM_STRIPE opt_geom.h
128 GEOM_SUNLABEL opt_geom.h
129 GEOM_UNCOMPRESS opt_geom.h
131 GEOM_VINUM opt_geom.h
132 GEOM_VIRSTOR opt_geom.h
135 KDTRACE_HOOKS opt_kdtrace.h
140 KTRACE_REQUEST_POOL opt_ktrace.h
143 MAC_BIBA opt_dontuse.h
144 MAC_BSDEXTENDED opt_dontuse.h
145 MAC_IFOFF opt_dontuse.h
146 MAC_LOMAC opt_dontuse.h
147 MAC_MLS opt_dontuse.h
148 MAC_NONE opt_dontuse.h
149 MAC_PARTITION opt_dontuse.h
150 MAC_PORTACL opt_dontuse.h
151 MAC_SEEOTHERUIDS opt_dontuse.h
153 MAC_STUB opt_dontuse.h
154 MAC_TEST opt_dontuse.h
156 MD_ROOT_FSTYPE opt_md.h
157 MD_ROOT_SIZE opt_md.h
159 MFI_DECODE_LOG opt_mfi.h
160 MPROF_BUFFERS opt_mprof.h
161 MPROF_HASH_SIZE opt_mprof.h
162 NEW_PCIB opt_global.h
163 NO_ADAPTIVE_MUTEXES opt_adaptive_mutexes.h
166 NO_EVENTTIMERS opt_timer.h
167 NO_SYSCTL_DESCR opt_global.h
168 NSWBUF_MIN opt_swap.h
169 MBUF_PACKET_ZONE_DISABLE opt_global.h
170 PANIC_REBOOT_WAIT_TIME opt_panic.h
172 PPC_PROBE_CHIPSET opt_ppc.h
174 PREEMPTION opt_sched.h
175 PROCDESC opt_procdesc.h
177 SCHED_4BSD opt_sched.h
178 SCHED_STATS opt_sched.h
179 SCHED_ULE opt_sched.h
181 SLHCI_DEBUG opt_slhci.h
198 SHMMAXPGS opt_sysvipc.h
202 SYSVMSG opt_sysvipc.h
203 SYSVSEM opt_sysvipc.h
204 SYSVSHM opt_sysvipc.h
205 SW_WATCHDOG opt_watchdog.h
209 VERBOSE_SYSINIT opt_global.h
210 WLCACHE opt_wavelan.h
211 WLDEBUG opt_wavelan.h
213 # POSIX kernel options
214 P1003_1B_MQUEUE opt_posix.h
215 P1003_1B_SEMAPHORES opt_posix.h
216 _KPOSIX_PRIORITY_SCHEDULING opt_posix.h
218 # Do we want the config file compiled into the kernel?
219 INCLUDE_CONFIG_FILE opt_config.h
221 # Options for static filesystems. These should only be used at config
222 # time, since the corresponding lkms cannot work if there are any static
223 # dependencies. Unusability is enforced by hiding the defines for the
224 # options in a never-included header.
228 FDESCFS opt_dontuse.h
231 MSDOSFS opt_dontuse.h
235 PSEUDOFS opt_dontuse.h
236 REISERFS opt_dontuse.h
240 UNIONFS opt_dontuse.h
244 PSEUDOFS_TRACE opt_pseudofs.h
247 KGSSAPI opt_kgssapi.h
248 KGSSAPI_DEBUG opt_kgssapi.h
250 # These static filesystems have one slightly bogus static dependency in
251 # sys/i386/i386/autoconf.c. If any of these filesystems are
252 # statically compiled into the kernel, code for mounting them as root
253 # filesystems will be enabled - but look below.
257 # Use these options to compile the experimental nfs client and/or
258 # server that supports NFSv4 into a kernel.
264 # filesystems and libiconv bridge
265 CD9660_ICONV opt_dontuse.h
266 MSDOSFS_ICONV opt_dontuse.h
267 UDF_ICONV opt_dontuse.h
269 # If you are following the conditions in the copyright,
270 # you can enable soft-updates which will speed up a lot of thigs
271 # and make the system safer from crashes at the same time.
272 # otherwise a STUB module will be compiled in.
273 SOFTUPDATES opt_ffs.h
275 # On small, embedded systems, it can be useful to turn off support for
276 # snapshots. It saves about 30-40k for a feature that would be lightly
277 # used, if it is used at all.
278 NO_FFS_SNAPSHOT opt_ffs.h
280 # Enabling this option turns on support for Access Control Lists in UFS,
281 # which can be used to support high security configurations. Depends on
285 # Enabling this option turns on support for extended attributes in UFS-based
286 # filesystems, which can be used to support high security configurations
287 # as well as new filesystem features.
288 UFS_EXTATTR opt_ufs.h
289 UFS_EXTATTR_AUTOSTART opt_ufs.h
291 # Enable fast hash lookups for large directories on UFS-based filesystems.
292 UFS_DIRHASH opt_ufs.h
294 # Enable gjournal-based UFS journal.
295 UFS_GJOURNAL opt_ufs.h
297 # The below sentence is not in English, and neither is this one.
298 # We plan to remove the static dependences above, with a
299 # <filesystem>_ROOT option to control if it usable as root. This list
300 # allows these options to be present in config files already (though
301 # they won't make any difference yet).
302 NFS_ROOT opt_nfsroot.h
307 # Options used only in subr_param.c.
312 VM_BCACHE_SIZE_MAX opt_param.h
313 VM_SWZONE_SIZE_MAX opt_param.h
319 # Generic SCSI options.
320 CAM_MAX_HIGHPOWER opt_cam.h
322 CAM_DEBUG_COMPILE opt_cam.h
323 CAM_DEBUG_DELAY opt_cam.h
324 CAM_DEBUG_BUS opt_cam.h
325 CAM_DEBUG_TARGET opt_cam.h
326 CAM_DEBUG_LUN opt_cam.h
327 CAM_DEBUG_FLAGS opt_cam.h
328 CAM_BOOT_DELAY opt_cam.h
329 SCSI_DELAY opt_scsi.h
330 SCSI_NO_SENSE_STRINGS opt_scsi.h
331 SCSI_NO_OP_STRINGS opt_scsi.h
333 # Options used only in cam/ata/ata_da.c
334 ADA_TEST_FAILURE opt_ada.h
335 ATA_STATIC_ID opt_ada.h
337 # Options used only in cam/scsi/scsi_cd.c
338 CHANGER_MIN_BUSY_SECONDS opt_cd.h
339 CHANGER_MAX_BUSY_SECONDS opt_cd.h
341 # Options used only in cam/scsi/scsi_sa.c.
342 SA_IO_TIMEOUT opt_sa.h
343 SA_SPACE_TIMEOUT opt_sa.h
344 SA_REWIND_TIMEOUT opt_sa.h
345 SA_ERASE_TIMEOUT opt_sa.h
346 SA_1FM_AT_EOD opt_sa.h
348 # Options used only in cam/scsi/scsi_pt.c
349 SCSI_PT_DEFAULT_TIMEOUT opt_pt.h
351 # Options used only in cam/scsi/scsi_ses.c
352 SES_ENABLE_PASSTHROUGH opt_ses.h
354 # Options used in dev/sym/ (Symbios SCSI driver).
355 SYM_SETUP_LP_PROBE_MAP opt_sym.h #-Low Priority Probe Map (bits)
356 # Allows the ncr to take precedence
357 # 1 (1<<0) -> 810a, 860
358 # 2 (1<<1) -> 825a, 875, 885, 895
359 # 4 (1<<2) -> 895a, 896, 1510d
360 SYM_SETUP_SCSI_DIFF opt_sym.h #-HVD support for 825a, 875, 885
361 # disabled:0 (default), enabled:1
362 SYM_SETUP_PCI_PARITY opt_sym.h #-PCI parity checking
363 # disabled:0, enabled:1 (default)
364 SYM_SETUP_MAX_LUN opt_sym.h #-Number of LUNs supported
365 # default:8, range:[1..64]
367 # Options used only in pci/ncr.c
368 SCSI_NCR_DEBUG opt_ncr.h
369 SCSI_NCR_MAX_SYNC opt_ncr.h
370 SCSI_NCR_MAX_WIDE opt_ncr.h
371 SCSI_NCR_MYADDR opt_ncr.h
373 # Options used only in dev/isp/*
374 ISP_TARGET_MODE opt_isp.h
375 ISP_FW_CRASH_DUMP opt_isp.h
376 ISP_DEFAULT_ROLES opt_isp.h
377 ISP_INTERNAL_TARGET opt_isp.h
378 ISP_FCTAPE_OFF opt_isp.h
380 # Options used only in dev/iscsi
381 ISCSI_INITIATOR_DEBUG opt_iscsi_initiator.h
390 ALTQ_CODEL opt_altq.h
391 ALTQ_DEBUG opt_altq.h
392 ALTQ_FAIRQ opt_altq.h
394 ALTQ_NOPCC opt_altq.h
399 BOOTP_BLOCKSIZE opt_bootp.h
400 BOOTP_COMPAT opt_bootp.h
401 BOOTP_NFSROOT opt_bootp.h
402 BOOTP_NFSV3 opt_bootp.h
403 BOOTP_WIRED_TO opt_bootp.h
418 IPFILTER opt_ipfilter.h
419 IPFILTER_DEFAULT_BLOCK opt_ipfilter.h
420 IPFILTER_LOG opt_ipfilter.h
421 IPFILTER_LOOKUP opt_ipfilter.h
422 IPFIREWALL opt_ipfw.h
423 IPFIREWALL_DEFAULT_TO_ACCEPT opt_ipfw.h
424 IPFIREWALL_NAT opt_ipfw.h
425 IPFIREWALL_VERBOSE opt_ipfw.h
426 IPFIREWALL_VERBOSE_LIMIT opt_ipfw.h
428 IPSEC_DEBUG opt_ipsec.h
429 IPSEC_FILTERTUNNEL opt_ipsec.h
430 IPSEC_NAT_T opt_ipsec.h
439 MROUTING opt_mrouting.h
442 PCBGROUP opt_pcbgroup.h
443 PF_DEFAULT_TO_DROP opt_pf.h
444 RADIX_MPATH opt_mpath.h
445 ROUTETABLES opt_route.h
446 SLIP_IFF_OPTS opt_slip.h
449 TCP_OFFLOAD opt_inet.h # Enable code to dispatch TCP offloading
450 TCP_RFC7413 opt_inet.h
451 TCP_RFC7413_MAX_KEYS opt_inet.h
452 TCP_SIGNATURE opt_inet.h
453 VLAN_ARRAY opt_vlan.h
455 FLOWTABLE opt_route.h
456 FLOWTABLE_HASH_ALL opt_route.h
462 SCTP_DEBUG opt_sctp.h # Enable debug printfs
463 SCTP_WITH_NO_CSUM opt_sctp.h # Use this at your peril
464 SCTP_LOCK_LOGGING opt_sctp.h # Log to KTR lock activity
465 SCTP_MBUF_LOGGING opt_sctp.h # Log to KTR general mbuf aloc/free
466 SCTP_MBCNT_LOGGING opt_sctp.h # Log to KTR mbcnt activity
467 SCTP_PACKET_LOGGING opt_sctp.h # Log to a packet buffer last N packets
468 SCTP_LTRACE_CHUNKS opt_sctp.h # Log to KTR chunks processed
469 SCTP_LTRACE_ERRORS opt_sctp.h # Log to KTR error returns.
470 SCTP_USE_PERCPU_STAT opt_sctp.h # Use per cpu stats.
471 SCTP_MCORE_INPUT opt_sctp.h # Have multiple input threads for input mbufs
472 SCTP_LOCAL_TRACE_BUF opt_sctp.h # Use tracebuffer exported via sysctl
473 SCTP_DETAILED_STR_STATS opt_sctp.h # Use per PR-SCTP policy stream stats
478 # Netgraph(4). Use option NETGRAPH to enable the base netgraph code.
479 # Each netgraph node type can be either be compiled into the kernel
480 # or loaded dynamically. To get the former, include the corresponding
481 # option below. Each type has its own man page, e.g. ng_async(4).
483 NETGRAPH_DEBUG opt_netgraph.h
484 NETGRAPH_ASYNC opt_netgraph.h
485 NETGRAPH_ATMLLC opt_netgraph.h
486 NETGRAPH_ATM_ATMPIF opt_netgraph.h
487 NETGRAPH_BLUETOOTH opt_netgraph.h
488 NETGRAPH_BLUETOOTH_BT3C opt_netgraph.h
489 NETGRAPH_BLUETOOTH_H4 opt_netgraph.h
490 NETGRAPH_BLUETOOTH_HCI opt_netgraph.h
491 NETGRAPH_BLUETOOTH_L2CAP opt_netgraph.h
492 NETGRAPH_BLUETOOTH_SOCKET opt_netgraph.h
493 NETGRAPH_BLUETOOTH_UBT opt_netgraph.h
494 NETGRAPH_BLUETOOTH_UBTBCMFW opt_netgraph.h
495 NETGRAPH_BPF opt_netgraph.h
496 NETGRAPH_BRIDGE opt_netgraph.h
497 NETGRAPH_CAR opt_netgraph.h
498 NETGRAPH_CISCO opt_netgraph.h
499 NETGRAPH_DEFLATE opt_netgraph.h
500 NETGRAPH_DEVICE opt_netgraph.h
501 NETGRAPH_ECHO opt_netgraph.h
502 NETGRAPH_EIFACE opt_netgraph.h
503 NETGRAPH_ETHER opt_netgraph.h
504 NETGRAPH_ETHER_ECHO opt_netgraph.h
505 NETGRAPH_FEC opt_netgraph.h
506 NETGRAPH_FRAME_RELAY opt_netgraph.h
507 NETGRAPH_GIF opt_netgraph.h
508 NETGRAPH_GIF_DEMUX opt_netgraph.h
509 NETGRAPH_HOLE opt_netgraph.h
510 NETGRAPH_IFACE opt_netgraph.h
511 NETGRAPH_IP_INPUT opt_netgraph.h
512 NETGRAPH_IPFW opt_netgraph.h
513 NETGRAPH_KSOCKET opt_netgraph.h
514 NETGRAPH_L2TP opt_netgraph.h
515 NETGRAPH_LMI opt_netgraph.h
516 NETGRAPH_MPPC_COMPRESSION opt_netgraph.h
517 NETGRAPH_MPPC_ENCRYPTION opt_netgraph.h
518 NETGRAPH_NAT opt_netgraph.h
519 NETGRAPH_NETFLOW opt_netgraph.h
520 NETGRAPH_ONE2MANY opt_netgraph.h
521 NETGRAPH_PATCH opt_netgraph.h
522 NETGRAPH_PIPE opt_netgraph.h
523 NETGRAPH_PPP opt_netgraph.h
524 NETGRAPH_PPPOE opt_netgraph.h
525 NETGRAPH_PPTPGRE opt_netgraph.h
526 NETGRAPH_PRED1 opt_netgraph.h
527 NETGRAPH_RFC1490 opt_netgraph.h
528 NETGRAPH_SOCKET opt_netgraph.h
529 NETGRAPH_SPLIT opt_netgraph.h
530 NETGRAPH_SPPP opt_netgraph.h
531 NETGRAPH_TAG opt_netgraph.h
532 NETGRAPH_TCPMSS opt_netgraph.h
533 NETGRAPH_TEE opt_netgraph.h
534 NETGRAPH_TTY opt_netgraph.h
535 NETGRAPH_UI opt_netgraph.h
536 NETGRAPH_VJC opt_netgraph.h
537 NETGRAPH_VLAN opt_netgraph.h
540 NGATM_ATM opt_netgraph.h
541 NGATM_ATMBASE opt_netgraph.h
542 NGATM_SSCOP opt_netgraph.h
543 NGATM_SSCFU opt_netgraph.h
544 NGATM_UNI opt_netgraph.h
545 NGATM_CCATM opt_netgraph.h
550 TI_SF_BUF_JUMBO opt_ti.h
551 TI_JUMBO_HDRSPLIT opt_ti.h
553 # XXX Conflict: # of devices vs network protocol (Native ATM).
554 # This makes "atm.h" unusable.
557 # DPT driver debug flags
558 DPT_MEASURE_PERFORMANCE opt_dpt.h
559 DPT_RESET_HBA opt_dpt.h
561 # Misc debug flags. Most of these should probably be replaced with
562 # 'DEBUG', and then let people recompile just the interesting modules
563 # with 'make CC="cc -DDEBUG"'.
564 CLUSTERDEBUG opt_debug_cluster.h
565 DEBUG_1284 opt_ppb_1284.h
568 PLIP_DEBUG opt_plip.h
569 LOCKF_DEBUG opt_debug_lockf.h
570 NETATALKDEBUG opt_atalk.h
571 SI_DEBUG opt_debug_si.h
575 FB_INSTALL_CDEV opt_fb.h
577 # ppbus related options
578 PERIPH_1284 opt_ppb_1284.h
579 DONTPROBE_1284 opt_ppb_1284.h
581 # smbus related options
582 ENABLE_ALART opt_intpm.h
584 # These cause changes all over the kernel
585 BLKDEV_IOSIZE opt_global.h
586 BURN_BRIDGES opt_global.h
588 DEBUG_LOCKS opt_global.h
589 DEBUG_VFS_LOCKS opt_global.h
590 DFLTPHYS opt_global.h
591 DIAGNOSTIC opt_global.h
592 INVARIANT_SUPPORT opt_global.h
593 INVARIANTS opt_global.h
595 MAXMEMDOM opt_global.h
597 MCLSHIFT opt_global.h
598 MUTEX_DEBUG opt_global.h
599 MUTEX_NOINLINE opt_global.h
600 LOCK_PROFILING opt_global.h
601 LOCK_PROFILING_FAST opt_global.h
603 REGRESSION opt_global.h
604 RWLOCK_NOINLINE opt_global.h
605 SX_NOINLINE opt_global.h
606 VFS_BIO_DEBUG opt_global.h
608 # These are VM related options
609 VM_KMEM_SIZE opt_vm.h
610 VM_KMEM_SIZE_SCALE opt_vm.h
611 VM_KMEM_SIZE_MAX opt_vm.h
612 VM_NRESERVLEVEL opt_vm.h
613 VM_LEVEL_0_ORDER opt_vm.h
615 MALLOC_MAKE_FAILURES opt_vm.h
616 MALLOC_PROFILE opt_vm.h
617 MALLOC_DEBUG_MAXZONES opt_vm.h
619 # The MemGuard replacement allocator used for tamper-after-free detection
620 DEBUG_MEMGUARD opt_vm.h
622 # The RedZone malloc(9) protection
623 DEBUG_REDZONE opt_vm.h
625 # Standard SMP options
628 # Size of the kernel message buffer
629 MSGBUF_SIZE opt_msgbuf.h
632 NFS_MINATTRTIMO opt_nfs.h
633 NFS_MAXATTRTIMO opt_nfs.h
634 NFS_MINDIRATTRTIMO opt_nfs.h
635 NFS_MAXDIRATTRTIMO opt_nfs.h
636 NFS_GATHERDELAY opt_nfs.h
637 NFS_WDELAYHASHSIZ opt_nfs.h
640 # For the Bt848/Bt848A/Bt849/Bt878/Bt879 driver
641 OVERRIDE_CARD opt_bktr.h
642 OVERRIDE_TUNER opt_bktr.h
643 OVERRIDE_DBX opt_bktr.h
644 OVERRIDE_MSP opt_bktr.h
645 BROOKTREE_SYSTEM_DEFAULT opt_bktr.h
646 BROOKTREE_ALLOC_PAGES opt_bktr.h
647 BKTR_OVERRIDE_CARD opt_bktr.h
648 BKTR_OVERRIDE_TUNER opt_bktr.h
649 BKTR_OVERRIDE_DBX opt_bktr.h
650 BKTR_OVERRIDE_MSP opt_bktr.h
651 BKTR_SYSTEM_DEFAULT opt_bktr.h
652 BKTR_ALLOC_PAGES opt_bktr.h
653 BKTR_USE_PLL opt_bktr.h
654 BKTR_GPIO_ACCESS opt_bktr.h
655 BKTR_NO_MSP_RESET opt_bktr.h
656 BKTR_430_FX_MODE opt_bktr.h
657 BKTR_SIS_VIA_MODE opt_bktr.h
658 BKTR_USE_FREEBSD_SMBUS opt_bktr.h
659 BKTR_NEW_MSP34XX_DRIVER opt_bktr.h
661 # Options for uart(4)
662 UART_PPS_ON_CTS opt_uart.h
663 UART_POLL_FREQ opt_uart.h
665 # options for bus/device framework
668 # options for USB support
670 USB_HOST_ALIGN opt_usb.h
671 USB_REQ_DEBUG opt_usb.h
672 USB_TEMPLATE opt_usb.h
673 USB_VERBOSE opt_usb.h
674 USB_DMA_SINGLE_ALLOC opt_usb.h
675 USB_EHCI_BIG_ENDIAN_DESC opt_usb.h
677 UKBD_DFLT_KEYMAP opt_ukbd.h
678 UPLCOM_INTR_INTERVAL opt_uplcom.h
679 UVSCOM_DEFAULT_OPKTSIZE opt_uvscom.h
680 UVSCOM_INTR_INTERVAL opt_uvscom.h
682 # Embedded system options
688 PCFCLOCK_VERBOSE opt_pcfclock.h
689 PCFCLOCK_MAX_RETRIES opt_pcfclock.h
694 KTR_CPUMASK opt_ktr.h
695 KTR_COMPILE opt_global.h
696 KTR_BOOT_ENTRIES opt_global.h
697 KTR_ENTRIES opt_global.h
698 KTR_VERBOSE opt_ktr.h
700 WITNESS_KDB opt_witness.h
701 WITNESS_NO_VNODE opt_witness.h
702 WITNESS_SKIPSPIN opt_witness.h
703 OPENSOLARIS_WITNESS opt_global.h
705 # options for ACPI support
706 ACPI_DEBUG opt_acpi.h
707 ACPI_MAX_TASKS opt_acpi.h
708 ACPI_MAX_THREADS opt_acpi.h
715 # various 'device presence' options.
717 DEV_NETMAP opt_global.h
720 DEV_SPLASH opt_splash.h
724 EISA_SLOTS opt_eisa.h
733 BCE_NVRAM_WRITE_SUPPORT opt_bce.h
735 SOCKBUF_DEBUG opt_global.h
738 # options for ubsec driver
739 UBSEC_DEBUG opt_ubsec.h
740 UBSEC_RNDTEST opt_ubsec.h
741 UBSEC_NO_RNG opt_ubsec.h
743 # options for hifn driver
744 HIFN_DEBUG opt_hifn.h
745 HIFN_RNDTEST opt_hifn.h
747 # options for safenet driver
748 SAFE_DEBUG opt_safe.h
749 SAFE_NO_RNG opt_safe.h
750 SAFE_RNDTEST opt_safe.h
753 MAXCONS opt_syscons.h
754 SC_ALT_MOUSE_IMAGE opt_syscons.h
755 SC_CUT_SPACES2TABS opt_syscons.h
756 SC_CUT_SEPCHARS opt_syscons.h
757 SC_DEBUG_LEVEL opt_syscons.h
758 SC_DFLT_FONT opt_syscons.h
759 SC_DISABLE_KDBKEY opt_syscons.h
760 SC_DISABLE_REBOOT opt_syscons.h
761 SC_HISTORY_SIZE opt_syscons.h
762 SC_KERNEL_CONS_ATTR opt_syscons.h
763 SC_KERNEL_CONS_REV_ATTR opt_syscons.h
764 SC_MOUSE_CHAR opt_syscons.h
765 SC_NO_CUTPASTE opt_syscons.h
766 SC_NO_FONT_LOADING opt_syscons.h
767 SC_NO_HISTORY opt_syscons.h
768 SC_NO_MODE_CHANGE opt_syscons.h
769 SC_NO_SUSPEND_VTYSWITCH opt_syscons.h
770 SC_NO_SYSMOUSE opt_syscons.h
771 SC_NORM_ATTR opt_syscons.h
772 SC_NORM_REV_ATTR opt_syscons.h
773 SC_PIXEL_MODE opt_syscons.h
774 SC_RENDER_DEBUG opt_syscons.h
775 SC_TWOBUTTON_MOUSE opt_syscons.h
776 VT_ALT_TO_ESC_HACK opt_syscons.h
777 VT_FB_DEFAULT_WIDTH opt_syscons.h
778 VT_FB_DEFAULT_HEIGHT opt_syscons.h
779 VT_MAXWINDOWS opt_syscons.h
780 VT_TWOBUTTON_MOUSE opt_syscons.h
784 # teken terminal emulator options
785 TEKEN_CONS25 opt_teken.h
786 TEKEN_UTF8 opt_teken.h
787 TERMINAL_KERN_ATTR opt_teken.h
788 TERMINAL_NORM_ATTR opt_teken.h
791 PRINTF_BUFR_SIZE opt_printf.h
794 KBD_DISABLE_KEYMAP_LOAD opt_kbd.h
795 KBD_INSTALL_CDEV opt_kbd.h
796 KBD_MAXRETRY opt_kbd.h
797 KBD_MAXWAIT opt_kbd.h
798 KBD_RESETDELAY opt_kbd.h
799 KBDIO_DEBUG opt_kbd.h
801 KBDMUX_DFLT_KEYMAP opt_kbdmux.h
803 # options for the Atheros driver
807 ATH_DIAGAPI opt_ath.h
808 ATH_TX99_DIAG opt_ath.h
809 ATH_ENABLE_11N opt_ath.h
810 ATH_ENABLE_DFS opt_ath.h
811 ATH_EEPROM_FIRMWARE opt_ath.h
812 ATH_ENABLE_RADIOTAP_VENDOR_EXT opt_ath.h
813 ATH_DEBUG_ALQ opt_ath.h
814 ATH_KTR_INTR_DEBUG opt_ath.h
816 # options for the Atheros hal
817 AH_SUPPORT_AR5416 opt_ah.h
818 # XXX For now, this breaks non-AR9130 chipsets, so only use it
819 # XXX when actually targetting AR9130.
820 AH_SUPPORT_AR9130 opt_ah.h
822 # This is required for AR933x SoC support
823 AH_SUPPORT_AR9330 opt_ah.h
824 AH_SUPPORT_AR9340 opt_ah.h
828 AH_DEBUG_ALQ opt_ah.h
829 AH_REGOPS_FUNC opt_ah.h
830 AH_WRITE_REGDOMAIN opt_ah.h
831 AH_DEBUG_COUNTRY opt_ah.h
832 AH_WRITE_EEPROM opt_ah.h
833 AH_PRIVATE_DIAG opt_ah.h
834 AH_NEED_DESC_SWAP opt_ah.h
835 AH_USE_INIPDGAIN opt_ah.h
837 AH_RXCFG_SDMAMW_4BYTES opt_ah.h
838 AH_INTERRUPT_DEBUGGING opt_ah.h
839 # AR5416 and later interrupt mitigation
840 # XXX do not use this for AR9130
841 AH_AR5416_INTERRUPT_MITIGATION opt_ah.h
843 # options for the Broadcom BCM43xx driver (bwi)
845 BWI_DEBUG_VERBOSE opt_bwi.h
847 # options for the Marvell 8335 wireless driver
848 MALO_DEBUG opt_malo.h
849 MALO_TXBUF opt_malo.h
850 MALO_RXBUF opt_malo.h
852 # options for the Marvell wireless driver
856 MWL_DIAGAPI opt_mwl.h
857 MWL_AGGR_SIZE opt_mwl.h
858 MWL_TX_NODROP opt_mwl.h
860 # Options for the Intel 802.11n wireless driver
864 DCONS_BUF_SIZE opt_dcons.h
865 DCONS_POLL_HZ opt_dcons.h
866 DCONS_FORCE_CONSOLE opt_dcons.h
867 DCONS_FORCE_GDB opt_dcons.h
870 HWPMC_DEBUG opt_global.h
872 HWPMC_MIPS_BACKTRACE opt_hwpmc_hooks.h
874 # XBOX options for FreeBSD/i386, but some files are MI
877 # Interrupt filtering
880 # 802.11 support layer
881 IEEE80211_DEBUG opt_wlan.h
882 IEEE80211_DEBUG_REFCNT opt_wlan.h
883 IEEE80211_AMPDU_AGE opt_wlan.h
884 IEEE80211_SUPPORT_MESH opt_wlan.h
885 IEEE80211_SUPPORT_SUPERG opt_wlan.h
886 IEEE80211_SUPPORT_TDMA opt_wlan.h
887 IEEE80211_ALQ opt_wlan.h
888 IEEE80211_DFS_DEBUG opt_wlan.h
890 # 802.11 TDMA support
891 TDMA_SLOTLEN_DEFAULT opt_tdma.h
892 TDMA_SLOTCNT_DEFAULT opt_tdma.h
893 TDMA_BINTVAL_DEFAULT opt_tdma.h
894 TDMA_TXRATE_11B_DEFAULT opt_tdma.h
895 TDMA_TXRATE_11G_DEFAULT opt_tdma.h
896 TDMA_TXRATE_11A_DEFAULT opt_tdma.h
897 TDMA_TXRATE_TURBO_DEFAULT opt_tdma.h
898 TDMA_TXRATE_HALF_DEFAULT opt_tdma.h
899 TDMA_TXRATE_QUARTER_DEFAULT opt_tdma.h
900 TDMA_TXRATE_11NA_DEFAULT opt_tdma.h
901 TDMA_TXRATE_11NG_DEFAULT opt_tdma.h
903 # Network stack virtualization options
905 VNET_DEBUG opt_global.h
907 # Common Flash Interface (CFI) options
908 CFI_SUPPORT_STRATAFLASH opt_cfi.h
909 CFI_ARMEDANDDANGEROUS opt_cfi.h
913 SND_DIAGNOSTIC opt_snd.h
914 SND_FEEDER_MULTIFORMAT opt_snd.h
915 SND_FEEDER_FULL_MULTIFORMAT opt_snd.h
916 SND_FEEDER_RATE_HP opt_snd.h
918 SND_OLDSTEREO opt_snd.h
922 # Flattened device tree options
924 FDT_DTB_STATIC opt_platform.h
926 # OFED Infiniband stack
928 OFED_DEBUG_INIT opt_ofed.h
932 IPOIB_DEBUG opt_ofed.h
935 # Resource Accounting
937 RACCT_DEFAULT_TO_DISABLED opt_global.h
942 # Random number generator(s)
943 RANDOM_YARROW opt_random.h
944 RANDOM_FORTUNA opt_random.h
945 RANDOM_DEBUG opt_random.h
946 RANDOM_RWFILE opt_random.h
949 EM_MULTIQUEUE opt_em.h
951 # Hyper-V network driver