MFC r260016:

[FreeBSD/stable/10.git] / sys / dev / ath / if_ath_tx.c

/*-
 * Copyright (c) 2002-2009 Sam Leffler, Errno Consulting
 * Copyright (c) 2010-2012 Adrian Chadd, Xenion Pty Ltd
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer,
 *    without modification.
 * 2. Redistributions in binary form must reproduce at minimum a disclaimer
 *    similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
 *    redistribution must be conditioned upon including a substantially
 *    similar Disclaimer requirement for further binary redistribution.
 *
 * NO WARRANTY
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
 * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
 * THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
 * OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
 * IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
 * THE POSSIBILITY OF SUCH DAMAGES.
 */

#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");

/*
 * Driver for the Atheros Wireless LAN controller.
 *
 * This software is derived from work of Atsushi Onoe; his contribution
 * is greatly appreciated.
 */

#include "opt_inet.h"
#include "opt_ath.h"
#include "opt_wlan.h"

#include <sys/param.h>
#include <sys/systm.h>
#include <sys/sysctl.h>
#include <sys/mbuf.h>
#include <sys/malloc.h>
#include <sys/lock.h>
#include <sys/mutex.h>
#include <sys/kernel.h>
#include <sys/socket.h>
#include <sys/sockio.h>
#include <sys/errno.h>
#include <sys/callout.h>
#include <sys/bus.h>
#include <sys/endian.h>
#include <sys/kthread.h>
#include <sys/taskqueue.h>
#include <sys/priv.h>

#include <machine/bus.h>

#include <net/if.h>
#include <net/if_dl.h>
#include <net/if_media.h>
#include <net/if_types.h>
#include <net/if_arp.h>
#include <net/ethernet.h>
#include <net/if_llc.h>

#include <net80211/ieee80211_var.h>
#include <net80211/ieee80211_regdomain.h>
#ifdef IEEE80211_SUPPORT_SUPERG
#include <net80211/ieee80211_superg.h>
#endif
#ifdef IEEE80211_SUPPORT_TDMA
#include <net80211/ieee80211_tdma.h>
#endif
#include <net80211/ieee80211_ht.h>

#include <net/bpf.h>

#ifdef INET
#include <netinet/in.h>
#include <netinet/if_ether.h>
#endif

#include <dev/ath/if_athvar.h>
#include <dev/ath/ath_hal/ah_devid.h>           /* XXX for softled */
#include <dev/ath/ath_hal/ah_diagcodes.h>

#include <dev/ath/if_ath_debug.h>

#ifdef ATH_TX99_DIAG
#include <dev/ath/ath_tx99/ath_tx99.h>
#endif

#include <dev/ath/if_ath_misc.h>
#include <dev/ath/if_ath_tx.h>
#include <dev/ath/if_ath_tx_ht.h>

#ifdef  ATH_DEBUG_ALQ
#include <dev/ath/if_ath_alq.h>
#endif

/*
 * How many retries to perform in software
 */
#define SWMAX_RETRIES           10

/*
 * What queue to throw the non-QoS TID traffic into
 */
#define ATH_NONQOS_TID_AC       WME_AC_VO

#if 0
static int ath_tx_node_is_asleep(struct ath_softc *sc, struct ath_node *an);
#endif
static int ath_tx_ampdu_pending(struct ath_softc *sc, struct ath_node *an,
    int tid);
static int ath_tx_ampdu_running(struct ath_softc *sc, struct ath_node *an,
    int tid);
static ieee80211_seq ath_tx_tid_seqno_assign(struct ath_softc *sc,
    struct ieee80211_node *ni, struct ath_buf *bf, struct mbuf *m0);
static int ath_tx_action_frame_override_queue(struct ath_softc *sc,
    struct ieee80211_node *ni, struct mbuf *m0, int *tid);
static struct ath_buf *
ath_tx_retry_clone(struct ath_softc *sc, struct ath_node *an,
    struct ath_tid *tid, struct ath_buf *bf);

#ifdef  ATH_DEBUG_ALQ
void
ath_tx_alq_post(struct ath_softc *sc, struct ath_buf *bf_first)
{
        struct ath_buf *bf;
        int i, n;
        const char *ds;

        /* XXX we should skip out early if debugging isn't enabled! */
        bf = bf_first;

        while (bf != NULL) {
                /* XXX should ensure bf_nseg > 0! */
                if (bf->bf_nseg == 0)
                        break;
                n = ((bf->bf_nseg - 1) / sc->sc_tx_nmaps) + 1;
                for (i = 0, ds = (const char *) bf->bf_desc;
                    i < n;
                    i++, ds += sc->sc_tx_desclen) {
                        if_ath_alq_post(&sc->sc_alq,
                            ATH_ALQ_EDMA_TXDESC,
                            sc->sc_tx_desclen,
                            ds);
                }
                bf = bf->bf_next;
        }
}
#endif /* ATH_DEBUG_ALQ */

/*
 * Whether to use the 11n rate scenario functions or not
 */
static inline int
ath_tx_is_11n(struct ath_softc *sc)
{
        return ((sc->sc_ah->ah_magic == 0x20065416) ||
                    (sc->sc_ah->ah_magic == 0x19741014));
}

/*
 * Obtain the current TID from the given frame.
 *
 * Non-QoS frames need to go into TID 16 (IEEE80211_NONQOS_TID.)
 * This has implications for which AC/priority the packet is placed
 * in.
 */
static int
ath_tx_gettid(struct ath_softc *sc, const struct mbuf *m0)
{
        const struct ieee80211_frame *wh;
        int pri = M_WME_GETAC(m0);

        wh = mtod(m0, const struct ieee80211_frame *);
        if (! IEEE80211_QOS_HAS_SEQ(wh))
                return IEEE80211_NONQOS_TID;
        else
                return WME_AC_TO_TID(pri);
}

static void
ath_tx_set_retry(struct ath_softc *sc, struct ath_buf *bf)
{
        struct ieee80211_frame *wh;

        wh = mtod(bf->bf_m, struct ieee80211_frame *);
        /* Only update/resync if needed */
        if (bf->bf_state.bfs_isretried == 0) {
                wh->i_fc[1] |= IEEE80211_FC1_RETRY;
                bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap,
                    BUS_DMASYNC_PREWRITE);
        }
        bf->bf_state.bfs_isretried = 1;
        bf->bf_state.bfs_retries ++;
}

/*
 * Determine what the correct AC queue for the given frame
 * should be.
 *
 * This code assumes that the TIDs map consistently to
 * the underlying hardware (or software) ath_txq.
 * Since the sender may try to set an AC which is
 * arbitrary, non-QoS TIDs may end up being put on
 * completely different ACs. There's no way to put a
 * TID into multiple ath_txq's for scheduling, so
 * for now we override the AC/TXQ selection and set
 * non-QOS TID frames into the BE queue.
 *
 * This may be completely incorrect - specifically,
 * some management frames may end up out of order
 * compared to the QoS traffic they're controlling.
 * I'll look into this later.
 */
static int
ath_tx_getac(struct ath_softc *sc, const struct mbuf *m0)
{
        const struct ieee80211_frame *wh;
        int pri = M_WME_GETAC(m0);
        wh = mtod(m0, const struct ieee80211_frame *);
        if (IEEE80211_QOS_HAS_SEQ(wh))
                return pri;

        return ATH_NONQOS_TID_AC;
}

void
ath_txfrag_cleanup(struct ath_softc *sc,
        ath_bufhead *frags, struct ieee80211_node *ni)
{
        struct ath_buf *bf, *next;

        ATH_TXBUF_LOCK_ASSERT(sc);

        TAILQ_FOREACH_SAFE(bf, frags, bf_list, next) {
                /* NB: bf assumed clean */
                TAILQ_REMOVE(frags, bf, bf_list);
                ath_returnbuf_head(sc, bf);
                ieee80211_node_decref(ni);
        }
}

/*
 * Setup xmit of a fragmented frame.  Allocate a buffer
 * for each frag and bump the node reference count to
 * reflect the held reference to be setup by ath_tx_start.
 */
int
ath_txfrag_setup(struct ath_softc *sc, ath_bufhead *frags,
        struct mbuf *m0, struct ieee80211_node *ni)
{
        struct mbuf *m;
        struct ath_buf *bf;

        ATH_TXBUF_LOCK(sc);
        for (m = m0->m_nextpkt; m != NULL; m = m->m_nextpkt) {
                /* XXX non-management? */
                bf = _ath_getbuf_locked(sc, ATH_BUFTYPE_NORMAL);
                if (bf == NULL) {       /* out of buffers, cleanup */
                        DPRINTF(sc, ATH_DEBUG_XMIT, "%s: no buffer?\n",
                            __func__);
                        ath_txfrag_cleanup(sc, frags, ni);
                        break;
                }
                ieee80211_node_incref(ni);
                TAILQ_INSERT_TAIL(frags, bf, bf_list);
        }
        ATH_TXBUF_UNLOCK(sc);

        return !TAILQ_EMPTY(frags);
}

/*
 * Reclaim mbuf resources.  For fragmented frames we
 * need to claim each frag chained with m_nextpkt.
 */
void
ath_freetx(struct mbuf *m)
{
        struct mbuf *next;

        do {
                next = m->m_nextpkt;
                m->m_nextpkt = NULL;
                m_freem(m);
        } while ((m = next) != NULL);
}

static int
ath_tx_dmasetup(struct ath_softc *sc, struct ath_buf *bf, struct mbuf *m0)
{
        struct mbuf *m;
        int error;

        /*
         * Load the DMA map so any coalescing is done.  This
         * also calculates the number of descriptors we need.
         */
        error = bus_dmamap_load_mbuf_sg(sc->sc_dmat, bf->bf_dmamap, m0,
                                     bf->bf_segs, &bf->bf_nseg,
                                     BUS_DMA_NOWAIT);
        if (error == EFBIG) {
                /* XXX packet requires too many descriptors */
                bf->bf_nseg = ATH_MAX_SCATTER + 1;
        } else if (error != 0) {
                sc->sc_stats.ast_tx_busdma++;
                ath_freetx(m0);
                return error;
        }
        /*
         * Discard null packets and check for packets that
         * require too many TX descriptors.  We try to convert
         * the latter to a cluster.
         */
        if (bf->bf_nseg > ATH_MAX_SCATTER) {            /* too many desc's, linearize */
                sc->sc_stats.ast_tx_linear++;
                m = m_collapse(m0, M_NOWAIT, ATH_MAX_SCATTER);
                if (m == NULL) {
                        ath_freetx(m0);
                        sc->sc_stats.ast_tx_nombuf++;
                        return ENOMEM;
                }
                m0 = m;
                error = bus_dmamap_load_mbuf_sg(sc->sc_dmat, bf->bf_dmamap, m0,
                                             bf->bf_segs, &bf->bf_nseg,
                                             BUS_DMA_NOWAIT);
                if (error != 0) {
                        sc->sc_stats.ast_tx_busdma++;
                        ath_freetx(m0);
                        return error;
                }
                KASSERT(bf->bf_nseg <= ATH_MAX_SCATTER,
                    ("too many segments after defrag; nseg %u", bf->bf_nseg));
        } else if (bf->bf_nseg == 0) {          /* null packet, discard */
                sc->sc_stats.ast_tx_nodata++;
                ath_freetx(m0);
                return EIO;
        }
        DPRINTF(sc, ATH_DEBUG_XMIT, "%s: m %p len %u\n",
                __func__, m0, m0->m_pkthdr.len);
        bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap, BUS_DMASYNC_PREWRITE);
        bf->bf_m = m0;

        return 0;
}

/*
 * Chain together segments+descriptors for a frame - 11n or otherwise.
 *
 * For aggregates, this is called on each frame in the aggregate.
 */
static void
ath_tx_chaindesclist(struct ath_softc *sc, struct ath_desc *ds0,
    struct ath_buf *bf, int is_aggr, int is_first_subframe,
    int is_last_subframe)
{
        struct ath_hal *ah = sc->sc_ah;
        char *ds;
        int i, bp, dsp;
        HAL_DMA_ADDR bufAddrList[4];
        uint32_t segLenList[4];
        int numTxMaps = 1;
        int isFirstDesc = 1;

        /*
         * XXX There's txdma and txdma_mgmt; the descriptor
         * sizes must match.
         */
        struct ath_descdma *dd = &sc->sc_txdma;

        /*
         * Fillin the remainder of the descriptor info.
         */

        /*
         * We need the number of TX data pointers in each descriptor.
         * EDMA and later chips support 4 TX buffers per descriptor;
         * previous chips just support one.
         */
        numTxMaps = sc->sc_tx_nmaps;

        /*
         * For EDMA and later chips ensure the TX map is fully populated
         * before advancing to the next descriptor.
         */
        ds = (char *) bf->bf_desc;
        bp = dsp = 0;
        bzero(bufAddrList, sizeof(bufAddrList));
        bzero(segLenList, sizeof(segLenList));
        for (i = 0; i < bf->bf_nseg; i++) {
                bufAddrList[bp] = bf->bf_segs[i].ds_addr;
                segLenList[bp] = bf->bf_segs[i].ds_len;
                bp++;

                /*
                 * Go to the next segment if this isn't the last segment
                 * and there's space in the current TX map.
                 */
                if ((i != bf->bf_nseg - 1) && (bp < numTxMaps))
                        continue;

                /*
                 * Last segment or we're out of buffer pointers.
                 */
                bp = 0;

                if (i == bf->bf_nseg - 1)
                        ath_hal_settxdesclink(ah, (struct ath_desc *) ds, 0);
                else
                        ath_hal_settxdesclink(ah, (struct ath_desc *) ds,
                            bf->bf_daddr + dd->dd_descsize * (dsp + 1));

                /*
                 * XXX This assumes that bfs_txq is the actual destination
                 * hardware queue at this point.  It may not have been
                 * assigned, it may actually be pointing to the multicast
                 * software TXQ id.  These must be fixed!
                 */
                ath_hal_filltxdesc(ah, (struct ath_desc *) ds
                        , bufAddrList
                        , segLenList
                        , bf->bf_descid         /* XXX desc id */
                        , bf->bf_state.bfs_tx_queue
                        , isFirstDesc           /* first segment */
                        , i == bf->bf_nseg - 1  /* last segment */
                        , (struct ath_desc *) ds0       /* first descriptor */
                );

                /*
                 * Make sure the 11n aggregate fields are cleared.
                 *
                 * XXX TODO: this doesn't need to be called for
                 * aggregate frames; as it'll be called on all
                 * sub-frames.  Since the descriptors are in
                 * non-cacheable memory, this leads to some
                 * rather slow writes on MIPS/ARM platforms.
                 */
                if (ath_tx_is_11n(sc))
                        ath_hal_clr11n_aggr(sc->sc_ah, (struct ath_desc *) ds);

                /*
                 * If 11n is enabled, set it up as if it's an aggregate
                 * frame.
                 */
                if (is_last_subframe) {
                        ath_hal_set11n_aggr_last(sc->sc_ah,
                            (struct ath_desc *) ds);
                } else if (is_aggr) {
                        /*
                         * This clears the aggrlen field; so
                         * the caller needs to call set_aggr_first()!
                         *
                         * XXX TODO: don't call this for the first
                         * descriptor in the first frame in an
                         * aggregate!
                         */
                        ath_hal_set11n_aggr_middle(sc->sc_ah,
                            (struct ath_desc *) ds,
                            bf->bf_state.bfs_ndelim);
                }
                isFirstDesc = 0;
                bf->bf_lastds = (struct ath_desc *) ds;

                /*
                 * Don't forget to skip to the next descriptor.
                 */
                ds += sc->sc_tx_desclen;
                dsp++;

                /*
                 * .. and don't forget to blank these out!
                 */
                bzero(bufAddrList, sizeof(bufAddrList));
                bzero(segLenList, sizeof(segLenList));
        }
        bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap, BUS_DMASYNC_PREWRITE);
}

/*
 * Set the rate control fields in the given descriptor based on
 * the bf_state fields and node state.
 *
 * The bfs fields should already be set with the relevant rate
 * control information, including whether MRR is to be enabled.
 *
 * Since the FreeBSD HAL currently sets up the first TX rate
 * in ath_hal_setuptxdesc(), this will setup the MRR
 * conditionally for the pre-11n chips, and call ath_buf_set_rate
 * unconditionally for 11n chips. These require the 11n rate
 * scenario to be set if MCS rates are enabled, so it's easier
 * to just always call it. The caller can then only set rates 2, 3
 * and 4 if multi-rate retry is needed.
 */
static void
ath_tx_set_ratectrl(struct ath_softc *sc, struct ieee80211_node *ni,
    struct ath_buf *bf)
{
        struct ath_rc_series *rc = bf->bf_state.bfs_rc;

        /* If mrr is disabled, blank tries 1, 2, 3 */
        if (! bf->bf_state.bfs_ismrr)
                rc[1].tries = rc[2].tries = rc[3].tries = 0;

#if 0
        /*
         * If NOACK is set, just set ntries=1.
         */
        else if (bf->bf_state.bfs_txflags & HAL_TXDESC_NOACK) {
                rc[1].tries = rc[2].tries = rc[3].tries = 0;
                rc[0].tries = 1;
        }
#endif

        /*
         * Always call - that way a retried descriptor will
         * have the MRR fields overwritten.
         *
         * XXX TODO: see if this is really needed - setting up
         * the first descriptor should set the MRR fields to 0
         * for us anyway.
         */
        if (ath_tx_is_11n(sc)) {
                ath_buf_set_rate(sc, ni, bf);
        } else {
                ath_hal_setupxtxdesc(sc->sc_ah, bf->bf_desc
                        , rc[1].ratecode, rc[1].tries
                        , rc[2].ratecode, rc[2].tries
                        , rc[3].ratecode, rc[3].tries
                );
        }
}

/*
 * Setup segments+descriptors for an 11n aggregate.
 * bf_first is the first buffer in the aggregate.
 * The descriptor list must already been linked together using
 * bf->bf_next.
 */
static void
ath_tx_setds_11n(struct ath_softc *sc, struct ath_buf *bf_first)
{
        struct ath_buf *bf, *bf_prev = NULL;
        struct ath_desc *ds0 = bf_first->bf_desc;

        DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR, "%s: nframes=%d, al=%d\n",
            __func__, bf_first->bf_state.bfs_nframes,
            bf_first->bf_state.bfs_al);

        bf = bf_first;

        if (bf->bf_state.bfs_txrate0 == 0)
                DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR, "%s: bf=%p, txrate0=%d\n",
                    __func__, bf, 0);
        if (bf->bf_state.bfs_rc[0].ratecode == 0)
                DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR, "%s: bf=%p, rix0=%d\n",
                    __func__, bf, 0);

        /*
         * Setup all descriptors of all subframes - this will
         * call ath_hal_set11naggrmiddle() on every frame.
         */
        while (bf != NULL) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
                    "%s: bf=%p, nseg=%d, pktlen=%d, seqno=%d\n",
                    __func__, bf, bf->bf_nseg, bf->bf_state.bfs_pktlen,
                    SEQNO(bf->bf_state.bfs_seqno));

                /*
                 * Setup the initial fields for the first descriptor - all
                 * the non-11n specific stuff.
                 */
                ath_hal_setuptxdesc(sc->sc_ah, bf->bf_desc
                        , bf->bf_state.bfs_pktlen       /* packet length */
                        , bf->bf_state.bfs_hdrlen       /* header length */
                        , bf->bf_state.bfs_atype        /* Atheros packet type */
                        , bf->bf_state.bfs_txpower      /* txpower */
                        , bf->bf_state.bfs_txrate0
                        , bf->bf_state.bfs_try0         /* series 0 rate/tries */
                        , bf->bf_state.bfs_keyix        /* key cache index */
                        , bf->bf_state.bfs_txantenna    /* antenna mode */
                        , bf->bf_state.bfs_txflags | HAL_TXDESC_INTREQ  /* flags */
                        , bf->bf_state.bfs_ctsrate      /* rts/cts rate */
                        , bf->bf_state.bfs_ctsduration  /* rts/cts duration */
                );

                /*
                 * First descriptor? Setup the rate control and initial
                 * aggregate header information.
                 */
                if (bf == bf_first) {
                        /*
                         * setup first desc with rate and aggr info
                         */
                        ath_tx_set_ratectrl(sc, bf->bf_node, bf);
                }

                /*
                 * Setup the descriptors for a multi-descriptor frame.
                 * This is both aggregate and non-aggregate aware.
                 */
                ath_tx_chaindesclist(sc, ds0, bf,
                    1, /* is_aggr */
                    !! (bf == bf_first), /* is_first_subframe */
                    !! (bf->bf_next == NULL) /* is_last_subframe */
                    );

                if (bf == bf_first) {
                        /*
                         * Initialise the first 11n aggregate with the
                         * aggregate length and aggregate enable bits.
                         */
                        ath_hal_set11n_aggr_first(sc->sc_ah,
                            ds0,
                            bf->bf_state.bfs_al,
                            bf->bf_state.bfs_ndelim);
                }

                /*
                 * Link the last descriptor of the previous frame
                 * to the beginning descriptor of this frame.
                 */
                if (bf_prev != NULL)
                        ath_hal_settxdesclink(sc->sc_ah, bf_prev->bf_lastds,
                            bf->bf_daddr);

                /* Save a copy so we can link the next descriptor in */
                bf_prev = bf;
                bf = bf->bf_next;
        }

        /*
         * Set the first descriptor bf_lastds field to point to
         * the last descriptor in the last subframe, that's where
         * the status update will occur.
         */
        bf_first->bf_lastds = bf_prev->bf_lastds;

        /*
         * And bf_last in the first descriptor points to the end of
         * the aggregate list.
         */
        bf_first->bf_last = bf_prev;

        /*
         * For non-AR9300 NICs, which require the rate control
         * in the final descriptor - let's set that up now.
         *
         * This is because the filltxdesc() HAL call doesn't
         * populate the last segment with rate control information
         * if firstSeg is also true.  For non-aggregate frames
         * that is fine, as the first frame already has rate control
         * info.  But if the last frame in an aggregate has one
         * descriptor, both firstseg and lastseg will be true and
         * the rate info isn't copied.
         *
         * This is inefficient on MIPS/ARM platforms that have
         * non-cachable memory for TX descriptors, but we'll just
         * make do for now.
         *
         * As to why the rate table is stashed in the last descriptor
         * rather than the first descriptor?  Because proctxdesc()
         * is called on the final descriptor in an MPDU or A-MPDU -
         * ie, the one that gets updated by the hardware upon
         * completion.  That way proctxdesc() doesn't need to know
         * about the first _and_ last TX descriptor.
         */
        ath_hal_setuplasttxdesc(sc->sc_ah, bf_prev->bf_lastds, ds0);

        DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR, "%s: end\n", __func__);
}

/*
 * Hand-off a frame to the multicast TX queue.
 *
 * This is a software TXQ which will be appended to the CAB queue
 * during the beacon setup code.
 *
 * XXX TODO: since the AR9300 EDMA TX queue support wants the QCU ID
 * as part of the TX descriptor, bf_state.bfs_tx_queue must be updated
 * with the actual hardware txq, or all of this will fall apart.
 *
 * XXX It may not be a bad idea to just stuff the QCU ID into bf_state
 * and retire bfs_tx_queue; then make sure the CABQ QCU ID is populated
 * correctly.
 */
static void
ath_tx_handoff_mcast(struct ath_softc *sc, struct ath_txq *txq,
    struct ath_buf *bf)
{
        ATH_TX_LOCK_ASSERT(sc);

        KASSERT((bf->bf_flags & ATH_BUF_BUSY) == 0,
             ("%s: busy status 0x%x", __func__, bf->bf_flags));

        /*
         * Ensure that the tx queue is the cabq, so things get
         * mapped correctly.
         */
        if (bf->bf_state.bfs_tx_queue != sc->sc_cabq->axq_qnum) {
                DPRINTF(sc, ATH_DEBUG_XMIT,
                    "%s: bf=%p, bfs_tx_queue=%d, axq_qnum=%d\n",
                    __func__, bf, bf->bf_state.bfs_tx_queue,
                    txq->axq_qnum);
        }

        ATH_TXQ_LOCK(txq);
        if (ATH_TXQ_LAST(txq, axq_q_s) != NULL) {
                struct ath_buf *bf_last = ATH_TXQ_LAST(txq, axq_q_s);
                struct ieee80211_frame *wh;

                /* mark previous frame */
                wh = mtod(bf_last->bf_m, struct ieee80211_frame *);
                wh->i_fc[1] |= IEEE80211_FC1_MORE_DATA;
                bus_dmamap_sync(sc->sc_dmat, bf_last->bf_dmamap,
                    BUS_DMASYNC_PREWRITE);

                /* link descriptor */
                ath_hal_settxdesclink(sc->sc_ah,
                    bf_last->bf_lastds,
                    bf->bf_daddr);
        }
        ATH_TXQ_INSERT_TAIL(txq, bf, bf_list);
        ATH_TXQ_UNLOCK(txq);
}

/*
 * Hand-off packet to a hardware queue.
 */
static void
ath_tx_handoff_hw(struct ath_softc *sc, struct ath_txq *txq,
    struct ath_buf *bf)
{
        struct ath_hal *ah = sc->sc_ah;
        struct ath_buf *bf_first;

        /*
         * Insert the frame on the outbound list and pass it on
         * to the hardware.  Multicast frames buffered for power
         * save stations and transmit from the CAB queue are stored
         * on a s/w only queue and loaded on to the CAB queue in
         * the SWBA handler since frames only go out on DTIM and
         * to avoid possible races.
         */
        ATH_TX_LOCK_ASSERT(sc);
        KASSERT((bf->bf_flags & ATH_BUF_BUSY) == 0,
             ("%s: busy status 0x%x", __func__, bf->bf_flags));
        KASSERT(txq->axq_qnum != ATH_TXQ_SWQ,
             ("ath_tx_handoff_hw called for mcast queue"));

        /*
         * XXX racy, should hold the PCU lock when checking this,
         * and also should ensure that the TX counter is >0!
         */
        KASSERT((sc->sc_inreset_cnt == 0),
            ("%s: TX during reset?\n", __func__));

#if 0
        /*
         * This causes a LOR. Find out where the PCU lock is being
         * held whilst the TXQ lock is grabbed - that shouldn't
         * be occuring.
         */
        ATH_PCU_LOCK(sc);
        if (sc->sc_inreset_cnt) {
                ATH_PCU_UNLOCK(sc);
                DPRINTF(sc, ATH_DEBUG_RESET,
                    "%s: called with sc_in_reset != 0\n",
                    __func__);
                DPRINTF(sc, ATH_DEBUG_XMIT,
                    "%s: queued: TXDP[%u] = %p (%p) depth %d\n",
                    __func__, txq->axq_qnum,
                    (caddr_t)bf->bf_daddr, bf->bf_desc,
                    txq->axq_depth);
                /* XXX axq_link needs to be set and updated! */
                ATH_TXQ_INSERT_TAIL(txq, bf, bf_list);
                if (bf->bf_state.bfs_aggr)
                        txq->axq_aggr_depth++;
                return;
                }
        ATH_PCU_UNLOCK(sc);
#endif

        ATH_TXQ_LOCK(txq);

        /*
         * XXX TODO: if there's a holdingbf, then
         * ATH_TXQ_PUTRUNNING should be clear.
         *
         * If there is a holdingbf and the list is empty,
         * then axq_link should be pointing to the holdingbf.
         *
         * Otherwise it should point to the last descriptor
         * in the last ath_buf.
         *
         * In any case, we should really ensure that we
         * update the previous descriptor link pointer to
         * this descriptor, regardless of all of the above state.
         *
         * For now this is captured by having axq_link point
         * to either the holdingbf (if the TXQ list is empty)
         * or the end of the list (if the TXQ list isn't empty.)
         * I'd rather just kill axq_link here and do it as above.
         */

        /*
         * Append the frame to the TX queue.
         */
        ATH_TXQ_INSERT_TAIL(txq, bf, bf_list);
        ATH_KTR(sc, ATH_KTR_TX, 3,
            "ath_tx_handoff: non-tdma: txq=%u, add bf=%p "
            "depth=%d",
            txq->axq_qnum,
            bf,
            txq->axq_depth);

        /*
         * If there's a link pointer, update it.
         *
         * XXX we should replace this with the above logic, just
         * to kill axq_link with fire.
         */
        if (txq->axq_link != NULL) {
                *txq->axq_link = bf->bf_daddr;
                DPRINTF(sc, ATH_DEBUG_XMIT,
                    "%s: link[%u](%p)=%p (%p) depth %d\n", __func__,
                    txq->axq_qnum, txq->axq_link,
                    (caddr_t)bf->bf_daddr, bf->bf_desc,
                    txq->axq_depth);
                ATH_KTR(sc, ATH_KTR_TX, 5,
                    "ath_tx_handoff: non-tdma: link[%u](%p)=%p (%p) "
                    "lastds=%d",
                    txq->axq_qnum, txq->axq_link,
                    (caddr_t)bf->bf_daddr, bf->bf_desc,
                    bf->bf_lastds);
        }

        /*
         * If we've not pushed anything into the hardware yet,
         * push the head of the queue into the TxDP.
         *
         * Once we've started DMA, there's no guarantee that
         * updating the TxDP with a new value will actually work.
         * So we just don't do that - if we hit the end of the list,
         * we keep that buffer around (the "holding buffer") and
         * re-start DMA by updating the link pointer of _that_
         * descriptor and then restart DMA.
         */
        if (! (txq->axq_flags & ATH_TXQ_PUTRUNNING)) {
                bf_first = TAILQ_FIRST(&txq->axq_q);
                txq->axq_flags |= ATH_TXQ_PUTRUNNING;
                ath_hal_puttxbuf(ah, txq->axq_qnum, bf_first->bf_daddr);
                DPRINTF(sc, ATH_DEBUG_XMIT,
                    "%s: TXDP[%u] = %p (%p) depth %d\n",
                    __func__, txq->axq_qnum,
                    (caddr_t)bf_first->bf_daddr, bf_first->bf_desc,
                    txq->axq_depth);
                ATH_KTR(sc, ATH_KTR_TX, 5,
                    "ath_tx_handoff: TXDP[%u] = %p (%p) "
                    "lastds=%p depth %d",
                    txq->axq_qnum,
                    (caddr_t)bf_first->bf_daddr, bf_first->bf_desc,
                    bf_first->bf_lastds,
                    txq->axq_depth);
        }

        /*
         * Ensure that the bf TXQ matches this TXQ, so later
         * checking and holding buffer manipulation is sane.
         */
        if (bf->bf_state.bfs_tx_queue != txq->axq_qnum) {
                DPRINTF(sc, ATH_DEBUG_XMIT,
                    "%s: bf=%p, bfs_tx_queue=%d, axq_qnum=%d\n",
                    __func__, bf, bf->bf_state.bfs_tx_queue,
                    txq->axq_qnum);
        }

        /*
         * Track aggregate queue depth.
         */
        if (bf->bf_state.bfs_aggr)
                txq->axq_aggr_depth++;

        /*
         * Update the link pointer.
         */
        ath_hal_gettxdesclinkptr(ah, bf->bf_lastds, &txq->axq_link);

        /*
         * Start DMA.
         *
         * If we wrote a TxDP above, DMA will start from here.
         *
         * If DMA is running, it'll do nothing.
         *
         * If the DMA engine hit the end of the QCU list (ie LINK=NULL,
         * or VEOL) then it stops at the last transmitted write.
         * We then append a new frame by updating the link pointer
         * in that descriptor and then kick TxE here; it will re-read
         * that last descriptor and find the new descriptor to transmit.
         *
         * This is why we keep the holding descriptor around.
         */
        ath_hal_txstart(ah, txq->axq_qnum);
        ATH_TXQ_UNLOCK(txq);
        ATH_KTR(sc, ATH_KTR_TX, 1,
            "ath_tx_handoff: txq=%u, txstart", txq->axq_qnum);
}

/*
 * Restart TX DMA for the given TXQ.
 *
 * This must be called whether the queue is empty or not.
 */
static void
ath_legacy_tx_dma_restart(struct ath_softc *sc, struct ath_txq *txq)
{
        struct ath_buf *bf, *bf_last;

        ATH_TXQ_LOCK_ASSERT(txq);

        /* XXX make this ATH_TXQ_FIRST */
        bf = TAILQ_FIRST(&txq->axq_q);
        bf_last = ATH_TXQ_LAST(txq, axq_q_s);

        if (bf == NULL)
                return;

        DPRINTF(sc, ATH_DEBUG_RESET,
            "%s: Q%d: bf=%p, bf_last=%p, daddr=0x%08x\n",
            __func__,
            txq->axq_qnum,
            bf,
            bf_last,
            (uint32_t) bf->bf_daddr);

#ifdef  ATH_DEBUG
        if (sc->sc_debug & ATH_DEBUG_RESET)
                ath_tx_dump(sc, txq);
#endif

        /*
         * This is called from a restart, so DMA is known to be
         * completely stopped.
         */
        KASSERT((!(txq->axq_flags & ATH_TXQ_PUTRUNNING)),
            ("%s: Q%d: called with PUTRUNNING=1\n",
            __func__,
            txq->axq_qnum));

        ath_hal_puttxbuf(sc->sc_ah, txq->axq_qnum, bf->bf_daddr);
        txq->axq_flags |= ATH_TXQ_PUTRUNNING;

        ath_hal_gettxdesclinkptr(sc->sc_ah, bf_last->bf_lastds,
            &txq->axq_link);
        ath_hal_txstart(sc->sc_ah, txq->axq_qnum);
}

/*
 * Hand off a packet to the hardware (or mcast queue.)
 *
 * The relevant hardware txq should be locked.
 */
static void
ath_legacy_xmit_handoff(struct ath_softc *sc, struct ath_txq *txq,
    struct ath_buf *bf)
{
        ATH_TX_LOCK_ASSERT(sc);

#ifdef  ATH_DEBUG_ALQ
        if (if_ath_alq_checkdebug(&sc->sc_alq, ATH_ALQ_EDMA_TXDESC))
                ath_tx_alq_post(sc, bf);
#endif

        if (txq->axq_qnum == ATH_TXQ_SWQ)
                ath_tx_handoff_mcast(sc, txq, bf);
        else
                ath_tx_handoff_hw(sc, txq, bf);
}

static int
ath_tx_tag_crypto(struct ath_softc *sc, struct ieee80211_node *ni,
    struct mbuf *m0, int iswep, int isfrag, int *hdrlen, int *pktlen,
    int *keyix)
{
        DPRINTF(sc, ATH_DEBUG_XMIT,
            "%s: hdrlen=%d, pktlen=%d, isfrag=%d, iswep=%d, m0=%p\n",
            __func__,
            *hdrlen,
            *pktlen,
            isfrag,
            iswep,
            m0);

        if (iswep) {
                const struct ieee80211_cipher *cip;
                struct ieee80211_key *k;

                /*
                 * Construct the 802.11 header+trailer for an encrypted
                 * frame. The only reason this can fail is because of an
                 * unknown or unsupported cipher/key type.
                 */
                k = ieee80211_crypto_encap(ni, m0);
                if (k == NULL) {
                        /*
                         * This can happen when the key is yanked after the
                         * frame was queued.  Just discard the frame; the
                         * 802.11 layer counts failures and provides
                         * debugging/diagnostics.
                         */
                        return (0);
                }
                /*
                 * Adjust the packet + header lengths for the crypto
                 * additions and calculate the h/w key index.  When
                 * a s/w mic is done the frame will have had any mic
                 * added to it prior to entry so m0->m_pkthdr.len will
                 * account for it. Otherwise we need to add it to the
                 * packet length.
                 */
                cip = k->wk_cipher;
                (*hdrlen) += cip->ic_header;
                (*pktlen) += cip->ic_header + cip->ic_trailer;
                /* NB: frags always have any TKIP MIC done in s/w */
                if ((k->wk_flags & IEEE80211_KEY_SWMIC) == 0 && !isfrag)
                        (*pktlen) += cip->ic_miclen;
                (*keyix) = k->wk_keyix;
        } else if (ni->ni_ucastkey.wk_cipher == &ieee80211_cipher_none) {
                /*
                 * Use station key cache slot, if assigned.
                 */
                (*keyix) = ni->ni_ucastkey.wk_keyix;
                if ((*keyix) == IEEE80211_KEYIX_NONE)
                        (*keyix) = HAL_TXKEYIX_INVALID;
        } else
                (*keyix) = HAL_TXKEYIX_INVALID;

        return (1);
}

/*
 * Calculate whether interoperability protection is required for
 * this frame.
 *
 * This requires the rate control information be filled in,
 * as the protection requirement depends upon the current
 * operating mode / PHY.
 */
static void
ath_tx_calc_protection(struct ath_softc *sc, struct ath_buf *bf)
{
        struct ieee80211_frame *wh;
        uint8_t rix;
        uint16_t flags;
        int shortPreamble;
        const HAL_RATE_TABLE *rt = sc->sc_currates;
        struct ifnet *ifp = sc->sc_ifp;
        struct ieee80211com *ic = ifp->if_l2com;

        flags = bf->bf_state.bfs_txflags;
        rix = bf->bf_state.bfs_rc[0].rix;
        shortPreamble = bf->bf_state.bfs_shpream;
        wh = mtod(bf->bf_m, struct ieee80211_frame *);

        /*
         * If 802.11g protection is enabled, determine whether
         * to use RTS/CTS or just CTS.  Note that this is only
         * done for OFDM unicast frames.
         */
        if ((ic->ic_flags & IEEE80211_F_USEPROT) &&
            rt->info[rix].phy == IEEE80211_T_OFDM &&
            (flags & HAL_TXDESC_NOACK) == 0) {
                bf->bf_state.bfs_doprot = 1;
                /* XXX fragments must use CCK rates w/ protection */
                if (ic->ic_protmode == IEEE80211_PROT_RTSCTS) {
                        flags |= HAL_TXDESC_RTSENA;
                } else if (ic->ic_protmode == IEEE80211_PROT_CTSONLY) {
                        flags |= HAL_TXDESC_CTSENA;
                }
                /*
                 * For frags it would be desirable to use the
                 * highest CCK rate for RTS/CTS.  But stations
                 * farther away may detect it at a lower CCK rate
                 * so use the configured protection rate instead
                 * (for now).
                 */
                sc->sc_stats.ast_tx_protect++;
        }

        /*
         * If 11n protection is enabled and it's a HT frame,
         * enable RTS.
         *
         * XXX ic_htprotmode or ic_curhtprotmode?
         * XXX should it_htprotmode only matter if ic_curhtprotmode 
         * XXX indicates it's not a HT pure environment?
         */
        if ((ic->ic_htprotmode == IEEE80211_PROT_RTSCTS) &&
            rt->info[rix].phy == IEEE80211_T_HT &&
            (flags & HAL_TXDESC_NOACK) == 0) {
                flags |= HAL_TXDESC_RTSENA;
                sc->sc_stats.ast_tx_htprotect++;
        }
        bf->bf_state.bfs_txflags = flags;
}

/*
 * Update the frame duration given the currently selected rate.
 *
 * This also updates the frame duration value, so it will require
 * a DMA flush.
 */
static void
ath_tx_calc_duration(struct ath_softc *sc, struct ath_buf *bf)
{
        struct ieee80211_frame *wh;
        uint8_t rix;
        uint16_t flags;
        int shortPreamble;
        struct ath_hal *ah = sc->sc_ah;
        const HAL_RATE_TABLE *rt = sc->sc_currates;
        int isfrag = bf->bf_m->m_flags & M_FRAG;

        flags = bf->bf_state.bfs_txflags;
        rix = bf->bf_state.bfs_rc[0].rix;
        shortPreamble = bf->bf_state.bfs_shpream;
        wh = mtod(bf->bf_m, struct ieee80211_frame *);

        /*
         * Calculate duration.  This logically belongs in the 802.11
         * layer but it lacks sufficient information to calculate it.
         */
        if ((flags & HAL_TXDESC_NOACK) == 0 &&
            (wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK) != IEEE80211_FC0_TYPE_CTL) {
                u_int16_t dur;
                if (shortPreamble)
                        dur = rt->info[rix].spAckDuration;
                else
                        dur = rt->info[rix].lpAckDuration;
                if (wh->i_fc[1] & IEEE80211_FC1_MORE_FRAG) {
                        dur += dur;             /* additional SIFS+ACK */
                        /*
                         * Include the size of next fragment so NAV is
                         * updated properly.  The last fragment uses only
                         * the ACK duration
                         *
                         * XXX TODO: ensure that the rate lookup for each
                         * fragment is the same as the rate used by the
                         * first fragment!
                         */
                        dur += ath_hal_computetxtime(ah,
                            rt,
                            bf->bf_nextfraglen,
                            rix, shortPreamble);
                }
                if (isfrag) {
                        /*
                         * Force hardware to use computed duration for next
                         * fragment by disabling multi-rate retry which updates
                         * duration based on the multi-rate duration table.
                         */
                        bf->bf_state.bfs_ismrr = 0;
                        bf->bf_state.bfs_try0 = ATH_TXMGTTRY;
                        /* XXX update bfs_rc[0].try? */
                }

                /* Update the duration field itself */
                *(u_int16_t *)wh->i_dur = htole16(dur);
        }
}

static uint8_t
ath_tx_get_rtscts_rate(struct ath_hal *ah, const HAL_RATE_TABLE *rt,
    int cix, int shortPreamble)
{
        uint8_t ctsrate;

        /*
         * CTS transmit rate is derived from the transmit rate
         * by looking in the h/w rate table.  We must also factor
         * in whether or not a short preamble is to be used.
         */
        /* NB: cix is set above where RTS/CTS is enabled */
        KASSERT(cix != 0xff, ("cix not setup"));
        ctsrate = rt->info[cix].rateCode;

        /* XXX this should only matter for legacy rates */
        if (shortPreamble)
                ctsrate |= rt->info[cix].shortPreamble;

        return (ctsrate);
}

/*
 * Calculate the RTS/CTS duration for legacy frames.
 */
static int
ath_tx_calc_ctsduration(struct ath_hal *ah, int rix, int cix,
    int shortPreamble, int pktlen, const HAL_RATE_TABLE *rt,
    int flags)
{
        int ctsduration = 0;

        /* This mustn't be called for HT modes */
        if (rt->info[cix].phy == IEEE80211_T_HT) {
                printf("%s: HT rate where it shouldn't be (0x%x)\n",
                    __func__, rt->info[cix].rateCode);
                return (-1);
        }

        /*
         * Compute the transmit duration based on the frame
         * size and the size of an ACK frame.  We call into the
         * HAL to do the computation since it depends on the
         * characteristics of the actual PHY being used.
         *
         * NB: CTS is assumed the same size as an ACK so we can
         *     use the precalculated ACK durations.
         */
        if (shortPreamble) {
                if (flags & HAL_TXDESC_RTSENA)          /* SIFS + CTS */
                        ctsduration += rt->info[cix].spAckDuration;
                ctsduration += ath_hal_computetxtime(ah,
                        rt, pktlen, rix, AH_TRUE);
                if ((flags & HAL_TXDESC_NOACK) == 0)    /* SIFS + ACK */
                        ctsduration += rt->info[rix].spAckDuration;
        } else {
                if (flags & HAL_TXDESC_RTSENA)          /* SIFS + CTS */
                        ctsduration += rt->info[cix].lpAckDuration;
                ctsduration += ath_hal_computetxtime(ah,
                        rt, pktlen, rix, AH_FALSE);
                if ((flags & HAL_TXDESC_NOACK) == 0)    /* SIFS + ACK */
                        ctsduration += rt->info[rix].lpAckDuration;
        }

        return (ctsduration);
}

/*
 * Update the given ath_buf with updated rts/cts setup and duration
 * values.
 *
 * To support rate lookups for each software retry, the rts/cts rate
 * and cts duration must be re-calculated.
 *
 * This function assumes the RTS/CTS flags have been set as needed;
 * mrr has been disabled; and the rate control lookup has been done.
 *
 * XXX TODO: MRR need only be disabled for the pre-11n NICs.
 * XXX The 11n NICs support per-rate RTS/CTS configuration.
 */
static void
ath_tx_set_rtscts(struct ath_softc *sc, struct ath_buf *bf)
{
        uint16_t ctsduration = 0;
        uint8_t ctsrate = 0;
        uint8_t rix = bf->bf_state.bfs_rc[0].rix;
        uint8_t cix = 0;
        const HAL_RATE_TABLE *rt = sc->sc_currates;

        /*
         * No RTS/CTS enabled? Don't bother.
         */
        if ((bf->bf_state.bfs_txflags &
            (HAL_TXDESC_RTSENA | HAL_TXDESC_CTSENA)) == 0) {
                /* XXX is this really needed? */
                bf->bf_state.bfs_ctsrate = 0;
                bf->bf_state.bfs_ctsduration = 0;
                return;
        }

        /*
         * If protection is enabled, use the protection rix control
         * rate. Otherwise use the rate0 control rate.
         */
        if (bf->bf_state.bfs_doprot)
                rix = sc->sc_protrix;
        else
                rix = bf->bf_state.bfs_rc[0].rix;

        /*
         * If the raw path has hard-coded ctsrate0 to something,
         * use it.
         */
        if (bf->bf_state.bfs_ctsrate0 != 0)
                cix = ath_tx_findrix(sc, bf->bf_state.bfs_ctsrate0);
        else
                /* Control rate from above */
                cix = rt->info[rix].controlRate;

        /* Calculate the rtscts rate for the given cix */
        ctsrate = ath_tx_get_rtscts_rate(sc->sc_ah, rt, cix,
            bf->bf_state.bfs_shpream);

        /* The 11n chipsets do ctsduration calculations for you */
        if (! ath_tx_is_11n(sc))
                ctsduration = ath_tx_calc_ctsduration(sc->sc_ah, rix, cix,
                    bf->bf_state.bfs_shpream, bf->bf_state.bfs_pktlen,
                    rt, bf->bf_state.bfs_txflags);

        /* Squirrel away in ath_buf */
        bf->bf_state.bfs_ctsrate = ctsrate;
        bf->bf_state.bfs_ctsduration = ctsduration;
        
        /*
         * Must disable multi-rate retry when using RTS/CTS.
         */
        if (!sc->sc_mrrprot) {
                bf->bf_state.bfs_ismrr = 0;
                bf->bf_state.bfs_try0 =
                    bf->bf_state.bfs_rc[0].tries = ATH_TXMGTTRY; /* XXX ew */
        }
}

/*
 * Setup the descriptor chain for a normal or fast-frame
 * frame.
 *
 * XXX TODO: extend to include the destination hardware QCU ID.
 * Make sure that is correct.  Make sure that when being added
 * to the mcastq, the CABQ QCUID is set or things will get a bit
 * odd.
 */
static void
ath_tx_setds(struct ath_softc *sc, struct ath_buf *bf)
{
        struct ath_desc *ds = bf->bf_desc;
        struct ath_hal *ah = sc->sc_ah;

        if (bf->bf_state.bfs_txrate0 == 0)
                DPRINTF(sc, ATH_DEBUG_XMIT, 
                    "%s: bf=%p, txrate0=%d\n", __func__, bf, 0);

        ath_hal_setuptxdesc(ah, ds
                , bf->bf_state.bfs_pktlen       /* packet length */
                , bf->bf_state.bfs_hdrlen       /* header length */
                , bf->bf_state.bfs_atype        /* Atheros packet type */
                , bf->bf_state.bfs_txpower      /* txpower */
                , bf->bf_state.bfs_txrate0
                , bf->bf_state.bfs_try0         /* series 0 rate/tries */
                , bf->bf_state.bfs_keyix        /* key cache index */
                , bf->bf_state.bfs_txantenna    /* antenna mode */
                , bf->bf_state.bfs_txflags      /* flags */
                , bf->bf_state.bfs_ctsrate      /* rts/cts rate */
                , bf->bf_state.bfs_ctsduration  /* rts/cts duration */
        );

        /*
         * This will be overriden when the descriptor chain is written.
         */
        bf->bf_lastds = ds;
        bf->bf_last = bf;

        /* Set rate control and descriptor chain for this frame */
        ath_tx_set_ratectrl(sc, bf->bf_node, bf);
        ath_tx_chaindesclist(sc, ds, bf, 0, 0, 0);
}

/*
 * Do a rate lookup.
 *
 * This performs a rate lookup for the given ath_buf only if it's required.
 * Non-data frames and raw frames don't require it.
 *
 * This populates the primary and MRR entries; MRR values are
 * then disabled later on if something requires it (eg RTS/CTS on
 * pre-11n chipsets.
 *
 * This needs to be done before the RTS/CTS fields are calculated
 * as they may depend upon the rate chosen.
 */
static void
ath_tx_do_ratelookup(struct ath_softc *sc, struct ath_buf *bf)
{
        uint8_t rate, rix;
        int try0;

        if (! bf->bf_state.bfs_doratelookup)
                return;

        /* Get rid of any previous state */
        bzero(bf->bf_state.bfs_rc, sizeof(bf->bf_state.bfs_rc));

        ATH_NODE_LOCK(ATH_NODE(bf->bf_node));
        ath_rate_findrate(sc, ATH_NODE(bf->bf_node), bf->bf_state.bfs_shpream,
            bf->bf_state.bfs_pktlen, &rix, &try0, &rate);

        /* In case MRR is disabled, make sure rc[0] is setup correctly */
        bf->bf_state.bfs_rc[0].rix = rix;
        bf->bf_state.bfs_rc[0].ratecode = rate;
        bf->bf_state.bfs_rc[0].tries = try0;

        if (bf->bf_state.bfs_ismrr && try0 != ATH_TXMAXTRY)
                ath_rate_getxtxrates(sc, ATH_NODE(bf->bf_node), rix,
                    bf->bf_state.bfs_rc);
        ATH_NODE_UNLOCK(ATH_NODE(bf->bf_node));

        sc->sc_txrix = rix;     /* for LED blinking */
        sc->sc_lastdatarix = rix;       /* for fast frames */
        bf->bf_state.bfs_try0 = try0;
        bf->bf_state.bfs_txrate0 = rate;
}

/*
 * Update the CLRDMASK bit in the ath_buf if it needs to be set.
 */
static void
ath_tx_update_clrdmask(struct ath_softc *sc, struct ath_tid *tid,
    struct ath_buf *bf)
{
        struct ath_node *an = ATH_NODE(bf->bf_node);

        ATH_TX_LOCK_ASSERT(sc);

        if (an->clrdmask == 1) {
                bf->bf_state.bfs_txflags |= HAL_TXDESC_CLRDMASK;
                an->clrdmask = 0;
        }
}

/*
 * Return whether this frame should be software queued or
 * direct dispatched.
 *
 * When doing powersave, BAR frames should be queued but other management
 * frames should be directly sent.
 *
 * When not doing powersave, stick BAR frames into the hardware queue
 * so it goes out even though the queue is paused.
 *
 * For now, management frames are also software queued by default.
 */
static int
ath_tx_should_swq_frame(struct ath_softc *sc, struct ath_node *an,
    struct mbuf *m0, int *queue_to_head)
{
        struct ieee80211_node *ni = &an->an_node;
        struct ieee80211_frame *wh;
        uint8_t type, subtype;

        wh = mtod(m0, struct ieee80211_frame *);
        type = wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK;
        subtype = wh->i_fc[0] & IEEE80211_FC0_SUBTYPE_MASK;

        (*queue_to_head) = 0;

        /* If it's not in powersave - direct-dispatch BAR */
        if ((ATH_NODE(ni)->an_is_powersave == 0)
            && type == IEEE80211_FC0_TYPE_CTL &&
            subtype == IEEE80211_FC0_SUBTYPE_BAR) {
                DPRINTF(sc, ATH_DEBUG_SW_TX,
                    "%s: BAR: TX'ing direct\n", __func__);
                return (0);
        } else if ((ATH_NODE(ni)->an_is_powersave == 1)
            && type == IEEE80211_FC0_TYPE_CTL &&
            subtype == IEEE80211_FC0_SUBTYPE_BAR) {
                /* BAR TX whilst asleep; queue */
                DPRINTF(sc, ATH_DEBUG_SW_TX,
                    "%s: swq: TX'ing\n", __func__);
                (*queue_to_head) = 1;
                return (1);
        } else if ((ATH_NODE(ni)->an_is_powersave == 1)
            && (type == IEEE80211_FC0_TYPE_MGT ||
                type == IEEE80211_FC0_TYPE_CTL)) {
                /*
                 * Other control/mgmt frame; bypass software queuing
                 * for now!
                 */
                DPRINTF(sc, ATH_DEBUG_XMIT, 
                    "%s: %6D: Node is asleep; sending mgmt "
                    "(type=%d, subtype=%d)\n",
                    __func__, ni->ni_macaddr, ":", type, subtype);
                return (0);
        } else {
                return (1);
        }
}


/*
 * Transmit the given frame to the hardware.
 *
 * The frame must already be setup; rate control must already have
 * been done.
 *
 * XXX since the TXQ lock is being held here (and I dislike holding
 * it for this long when not doing software aggregation), later on
 * break this function into "setup_normal" and "xmit_normal". The
 * lock only needs to be held for the ath_tx_handoff call.
 *
 * XXX we don't update the leak count here - if we're doing
 * direct frame dispatch, we need to be able to do it without
 * decrementing the leak count (eg multicast queue frames.)
 */
static void
ath_tx_xmit_normal(struct ath_softc *sc, struct ath_txq *txq,
    struct ath_buf *bf)
{
        struct ath_node *an = ATH_NODE(bf->bf_node);
        struct ath_tid *tid = &an->an_tid[bf->bf_state.bfs_tid];

        ATH_TX_LOCK_ASSERT(sc);

        /*
         * For now, just enable CLRDMASK. ath_tx_xmit_normal() does
         * set a completion handler however it doesn't (yet) properly
         * handle the strict ordering requirements needed for normal,
         * non-aggregate session frames.
         *
         * Once this is implemented, only set CLRDMASK like this for
         * frames that must go out - eg management/raw frames.
         */
        bf->bf_state.bfs_txflags |= HAL_TXDESC_CLRDMASK;

        /* Setup the descriptor before handoff */
        ath_tx_do_ratelookup(sc, bf);
        ath_tx_calc_duration(sc, bf);
        ath_tx_calc_protection(sc, bf);
        ath_tx_set_rtscts(sc, bf);
        ath_tx_rate_fill_rcflags(sc, bf);
        ath_tx_setds(sc, bf);

        /* Track per-TID hardware queue depth correctly */
        tid->hwq_depth++;

        /* Assign the completion handler */
        bf->bf_comp = ath_tx_normal_comp;

        /* Hand off to hardware */
        ath_tx_handoff(sc, txq, bf);
}

/*
 * Do the basic frame setup stuff that's required before the frame
 * is added to a software queue.
 *
 * All frames get mostly the same treatment and it's done once.
 * Retransmits fiddle with things like the rate control setup,
 * setting the retransmit bit in the packet; doing relevant DMA/bus
 * syncing and relinking it (back) into the hardware TX queue.
 *
 * Note that this may cause the mbuf to be reallocated, so
 * m0 may not be valid.
 */
static int
ath_tx_normal_setup(struct ath_softc *sc, struct ieee80211_node *ni,
    struct ath_buf *bf, struct mbuf *m0, struct ath_txq *txq)
{
        struct ieee80211vap *vap = ni->ni_vap;
        struct ath_hal *ah = sc->sc_ah;
        struct ifnet *ifp = sc->sc_ifp;
        struct ieee80211com *ic = ifp->if_l2com;
        const struct chanAccParams *cap = &ic->ic_wme.wme_chanParams;
        int error, iswep, ismcast, isfrag, ismrr;
        int keyix, hdrlen, pktlen, try0 = 0;
        u_int8_t rix = 0, txrate = 0;
        struct ath_desc *ds;
        struct ieee80211_frame *wh;
        u_int subtype, flags;
        HAL_PKT_TYPE atype;
        const HAL_RATE_TABLE *rt;
        HAL_BOOL shortPreamble;
        struct ath_node *an;
        u_int pri;

        /*
         * To ensure that both sequence numbers and the CCMP PN handling
         * is "correct", make sure that the relevant TID queue is locked.
         * Otherwise the CCMP PN and seqno may appear out of order, causing
         * re-ordered frames to have out of order CCMP PN's, resulting
         * in many, many frame drops.
         */
        ATH_TX_LOCK_ASSERT(sc);

        wh = mtod(m0, struct ieee80211_frame *);
        iswep = wh->i_fc[1] & IEEE80211_FC1_WEP;
        ismcast = IEEE80211_IS_MULTICAST(wh->i_addr1);
        isfrag = m0->m_flags & M_FRAG;
        hdrlen = ieee80211_anyhdrsize(wh);
        /*
         * Packet length must not include any
         * pad bytes; deduct them here.
         */
        pktlen = m0->m_pkthdr.len - (hdrlen & 3);

        /* Handle encryption twiddling if needed */
        if (! ath_tx_tag_crypto(sc, ni, m0, iswep, isfrag, &hdrlen,
            &pktlen, &keyix)) {
                ath_freetx(m0);
                return EIO;
        }

        /* packet header may have moved, reset our local pointer */
        wh = mtod(m0, struct ieee80211_frame *);

        pktlen += IEEE80211_CRC_LEN;

        /*
         * Load the DMA map so any coalescing is done.  This
         * also calculates the number of descriptors we need.
         */
        error = ath_tx_dmasetup(sc, bf, m0);
        if (error != 0)
                return error;
        bf->bf_node = ni;                       /* NB: held reference */
        m0 = bf->bf_m;                          /* NB: may have changed */
        wh = mtod(m0, struct ieee80211_frame *);

        /* setup descriptors */
        ds = bf->bf_desc;
        rt = sc->sc_currates;
        KASSERT(rt != NULL, ("no rate table, mode %u", sc->sc_curmode));

        /*
         * NB: the 802.11 layer marks whether or not we should
         * use short preamble based on the current mode and
         * negotiated parameters.
         */
        if ((ic->ic_flags & IEEE80211_F_SHPREAMBLE) &&
            (ni->ni_capinfo & IEEE80211_CAPINFO_SHORT_PREAMBLE)) {
                shortPreamble = AH_TRUE;
                sc->sc_stats.ast_tx_shortpre++;
        } else {
                shortPreamble = AH_FALSE;
        }

        an = ATH_NODE(ni);
        //flags = HAL_TXDESC_CLRDMASK;          /* XXX needed for crypto errs */
        flags = 0;
        ismrr = 0;                              /* default no multi-rate retry*/
        pri = M_WME_GETAC(m0);                  /* honor classification */
        /* XXX use txparams instead of fixed values */
        /*
         * Calculate Atheros packet type from IEEE80211 packet header,
         * setup for rate calculations, and select h/w transmit queue.
         */
        switch (wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK) {
        case IEEE80211_FC0_TYPE_MGT:
                subtype = wh->i_fc[0] & IEEE80211_FC0_SUBTYPE_MASK;
                if (subtype == IEEE80211_FC0_SUBTYPE_BEACON)
                        atype = HAL_PKT_TYPE_BEACON;
                else if (subtype == IEEE80211_FC0_SUBTYPE_PROBE_RESP)
                        atype = HAL_PKT_TYPE_PROBE_RESP;
                else if (subtype == IEEE80211_FC0_SUBTYPE_ATIM)
                        atype = HAL_PKT_TYPE_ATIM;
                else
                        atype = HAL_PKT_TYPE_NORMAL;    /* XXX */
                rix = an->an_mgmtrix;
                txrate = rt->info[rix].rateCode;
                if (shortPreamble)
                        txrate |= rt->info[rix].shortPreamble;
                try0 = ATH_TXMGTTRY;
                flags |= HAL_TXDESC_INTREQ;     /* force interrupt */
                break;
        case IEEE80211_FC0_TYPE_CTL:
                atype = HAL_PKT_TYPE_PSPOLL;    /* stop setting of duration */
                rix = an->an_mgmtrix;
                txrate = rt->info[rix].rateCode;
                if (shortPreamble)
                        txrate |= rt->info[rix].shortPreamble;
                try0 = ATH_TXMGTTRY;
                flags |= HAL_TXDESC_INTREQ;     /* force interrupt */
                break;
        case IEEE80211_FC0_TYPE_DATA:
                atype = HAL_PKT_TYPE_NORMAL;            /* default */
                /*
                 * Data frames: multicast frames go out at a fixed rate,
                 * EAPOL frames use the mgmt frame rate; otherwise consult
                 * the rate control module for the rate to use.
                 */
                if (ismcast) {
                        rix = an->an_mcastrix;
                        txrate = rt->info[rix].rateCode;
                        if (shortPreamble)
                                txrate |= rt->info[rix].shortPreamble;
                        try0 = 1;
                } else if (m0->m_flags & M_EAPOL) {
                        /* XXX? maybe always use long preamble? */
                        rix = an->an_mgmtrix;
                        txrate = rt->info[rix].rateCode;
                        if (shortPreamble)
                                txrate |= rt->info[rix].shortPreamble;
                        try0 = ATH_TXMAXTRY;    /* XXX?too many? */
                } else {
                        /*
                         * Do rate lookup on each TX, rather than using
                         * the hard-coded TX information decided here.
                         */
                        ismrr = 1;
                        bf->bf_state.bfs_doratelookup = 1;
                }
                if (cap->cap_wmeParams[pri].wmep_noackPolicy)
                        flags |= HAL_TXDESC_NOACK;
                break;
        default:
                if_printf(ifp, "bogus frame type 0x%x (%s)\n",
                        wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK, __func__);
                /* XXX statistic */
                /* XXX free tx dmamap */
                ath_freetx(m0);
                return EIO;
        }

        /*
         * There are two known scenarios where the frame AC doesn't match
         * what the destination TXQ is.
         *
         * + non-QoS frames (eg management?) that the net80211 stack has
         *   assigned a higher AC to, but since it's a non-QoS TID, it's
         *   being thrown into TID 16.  TID 16 gets the AC_BE queue.
         *   It's quite possible that management frames should just be
         *   direct dispatched to hardware rather than go via the software
         *   queue; that should be investigated in the future.  There are
         *   some specific scenarios where this doesn't make sense, mostly
         *   surrounding ADDBA request/response - hence why that is special
         *   cased.
         *
         * + Multicast frames going into the VAP mcast queue.  That shows up
         *   as "TXQ 11".
         *
         * This driver should eventually support separate TID and TXQ locking,
         * allowing for arbitrary AC frames to appear on arbitrary software
         * queues, being queued to the "correct" hardware queue when needed.
         */
#if 0
        if (txq != sc->sc_ac2q[pri]) {
                DPRINTF(sc, ATH_DEBUG_XMIT, 
                    "%s: txq=%p (%d), pri=%d, pri txq=%p (%d)\n",
                    __func__,
                    txq,
                    txq->axq_qnum,
                    pri,
                    sc->sc_ac2q[pri],
                    sc->sc_ac2q[pri]->axq_qnum);
        }
#endif

        /*
         * Calculate miscellaneous flags.
         */
        if (ismcast) {
                flags |= HAL_TXDESC_NOACK;      /* no ack on broad/multicast */
        } else if (pktlen > vap->iv_rtsthreshold &&
            (ni->ni_ath_flags & IEEE80211_NODE_FF) == 0) {
                flags |= HAL_TXDESC_RTSENA;     /* RTS based on frame length */
                sc->sc_stats.ast_tx_rts++;
        }
        if (flags & HAL_TXDESC_NOACK)           /* NB: avoid double counting */
                sc->sc_stats.ast_tx_noack++;
#ifdef IEEE80211_SUPPORT_TDMA
        if (sc->sc_tdma && (flags & HAL_TXDESC_NOACK) == 0) {
                DPRINTF(sc, ATH_DEBUG_TDMA,
                    "%s: discard frame, ACK required w/ TDMA\n", __func__);
                sc->sc_stats.ast_tdma_ack++;
                /* XXX free tx dmamap */
                ath_freetx(m0);
                return EIO;
        }
#endif

        /*
         * Determine if a tx interrupt should be generated for
         * this descriptor.  We take a tx interrupt to reap
         * descriptors when the h/w hits an EOL condition or
         * when the descriptor is specifically marked to generate
         * an interrupt.  We periodically mark descriptors in this
         * way to insure timely replenishing of the supply needed
         * for sending frames.  Defering interrupts reduces system
         * load and potentially allows more concurrent work to be
         * done but if done to aggressively can cause senders to
         * backup.
         *
         * NB: use >= to deal with sc_txintrperiod changing
         *     dynamically through sysctl.
         */
        if (flags & HAL_TXDESC_INTREQ) {
                txq->axq_intrcnt = 0;
        } else if (++txq->axq_intrcnt >= sc->sc_txintrperiod) {
                flags |= HAL_TXDESC_INTREQ;
                txq->axq_intrcnt = 0;
        }

        /* This point forward is actual TX bits */

        /*
         * At this point we are committed to sending the frame
         * and we don't need to look at m_nextpkt; clear it in
         * case this frame is part of frag chain.
         */
        m0->m_nextpkt = NULL;

        if (IFF_DUMPPKTS(sc, ATH_DEBUG_XMIT))
                ieee80211_dump_pkt(ic, mtod(m0, const uint8_t *), m0->m_len,
                    sc->sc_hwmap[rix].ieeerate, -1);

        if (ieee80211_radiotap_active_vap(vap)) {
                u_int64_t tsf = ath_hal_gettsf64(ah);

                sc->sc_tx_th.wt_tsf = htole64(tsf);
                sc->sc_tx_th.wt_flags = sc->sc_hwmap[rix].txflags;
                if (iswep)
                        sc->sc_tx_th.wt_flags |= IEEE80211_RADIOTAP_F_WEP;
                if (isfrag)
                        sc->sc_tx_th.wt_flags |= IEEE80211_RADIOTAP_F_FRAG;
                sc->sc_tx_th.wt_rate = sc->sc_hwmap[rix].ieeerate;
                sc->sc_tx_th.wt_txpower = ieee80211_get_node_txpower(ni);
                sc->sc_tx_th.wt_antenna = sc->sc_txantenna;

                ieee80211_radiotap_tx(vap, m0);
        }

        /* Blank the legacy rate array */
        bzero(&bf->bf_state.bfs_rc, sizeof(bf->bf_state.bfs_rc));

        /*
         * ath_buf_set_rate needs at least one rate/try to setup
         * the rate scenario.
         */
        bf->bf_state.bfs_rc[0].rix = rix;
        bf->bf_state.bfs_rc[0].tries = try0;
        bf->bf_state.bfs_rc[0].ratecode = txrate;

        /* Store the decided rate index values away */
        bf->bf_state.bfs_pktlen = pktlen;
        bf->bf_state.bfs_hdrlen = hdrlen;
        bf->bf_state.bfs_atype = atype;
        bf->bf_state.bfs_txpower = ieee80211_get_node_txpower(ni);
        bf->bf_state.bfs_txrate0 = txrate;
        bf->bf_state.bfs_try0 = try0;
        bf->bf_state.bfs_keyix = keyix;
        bf->bf_state.bfs_txantenna = sc->sc_txantenna;
        bf->bf_state.bfs_txflags = flags;
        bf->bf_state.bfs_shpream = shortPreamble;

        /* XXX this should be done in ath_tx_setrate() */
        bf->bf_state.bfs_ctsrate0 = 0;  /* ie, no hard-coded ctsrate */
        bf->bf_state.bfs_ctsrate = 0;   /* calculated later */
        bf->bf_state.bfs_ctsduration = 0;
        bf->bf_state.bfs_ismrr = ismrr;

        return 0;
}

/*
 * Queue a frame to the hardware or software queue.
 *
 * This can be called by the net80211 code.
 *
 * XXX what about locking? Or, push the seqno assign into the
 * XXX aggregate scheduler so its serialised?
 *
 * XXX When sending management frames via ath_raw_xmit(),
 *     should CLRDMASK be set unconditionally?
 */
int
ath_tx_start(struct ath_softc *sc, struct ieee80211_node *ni,
    struct ath_buf *bf, struct mbuf *m0)
{
        struct ieee80211vap *vap = ni->ni_vap;
        struct ath_vap *avp = ATH_VAP(vap);
        int r = 0;
        u_int pri;
        int tid;
        struct ath_txq *txq;
        int ismcast;
        const struct ieee80211_frame *wh;
        int is_ampdu, is_ampdu_tx, is_ampdu_pending;
        ieee80211_seq seqno;
        uint8_t type, subtype;
        int queue_to_head;

        ATH_TX_LOCK_ASSERT(sc);

        /*
         * Determine the target hardware queue.
         *
         * For multicast frames, the txq gets overridden appropriately
         * depending upon the state of PS.
         *
         * For any other frame, we do a TID/QoS lookup inside the frame
         * to see what the TID should be. If it's a non-QoS frame, the
         * AC and TID are overridden. The TID/TXQ code assumes the
         * TID is on a predictable hardware TXQ, so we don't support
         * having a node TID queued to multiple hardware TXQs.
         * This may change in the future but would require some locking
         * fudgery.
         */
        pri = ath_tx_getac(sc, m0);
        tid = ath_tx_gettid(sc, m0);

        txq = sc->sc_ac2q[pri];
        wh = mtod(m0, struct ieee80211_frame *);
        ismcast = IEEE80211_IS_MULTICAST(wh->i_addr1);
        type = wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK;
        subtype = wh->i_fc[0] & IEEE80211_FC0_SUBTYPE_MASK;

        /*
         * Enforce how deep the multicast queue can grow.
         *
         * XXX duplicated in ath_raw_xmit().
         */
        if (IEEE80211_IS_MULTICAST(wh->i_addr1)) {
                if (sc->sc_cabq->axq_depth + sc->sc_cabq->fifo.axq_depth
                    > sc->sc_txq_mcastq_maxdepth) {
                        sc->sc_stats.ast_tx_mcastq_overflow++;
                        m_freem(m0);
                        return (ENOBUFS);
                }
        }

        /*
         * Enforce how deep the unicast queue can grow.
         *
         * If the node is in power save then we don't want
         * the software queue to grow too deep, or a node may
         * end up consuming all of the ath_buf entries.
         *
         * For now, only do this for DATA frames.
         *
         * We will want to cap how many management/control
         * frames get punted to the software queue so it doesn't
         * fill up.  But the correct solution isn't yet obvious.
         * In any case, this check should at least let frames pass
         * that we are direct-dispatching.
         *
         * XXX TODO: duplicate this to the raw xmit path!
         */
        if (type == IEEE80211_FC0_TYPE_DATA &&
            ATH_NODE(ni)->an_is_powersave &&
            ATH_NODE(ni)->an_swq_depth >
             sc->sc_txq_node_psq_maxdepth) {
                sc->sc_stats.ast_tx_node_psq_overflow++;
                m_freem(m0);
                return (ENOBUFS);
        }

        /* A-MPDU TX */
        is_ampdu_tx = ath_tx_ampdu_running(sc, ATH_NODE(ni), tid);
        is_ampdu_pending = ath_tx_ampdu_pending(sc, ATH_NODE(ni), tid);
        is_ampdu = is_ampdu_tx | is_ampdu_pending;

        DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: tid=%d, ac=%d, is_ampdu=%d\n",
            __func__, tid, pri, is_ampdu);

        /* Set local packet state, used to queue packets to hardware */
        bf->bf_state.bfs_tid = tid;
        bf->bf_state.bfs_tx_queue = txq->axq_qnum;
        bf->bf_state.bfs_pri = pri;

#if 1
        /*
         * When servicing one or more stations in power-save mode
         * (or) if there is some mcast data waiting on the mcast
         * queue (to prevent out of order delivery) multicast frames
         * must be bufferd until after the beacon.
         *
         * TODO: we should lock the mcastq before we check the length.
         */
        if (sc->sc_cabq_enable && ismcast && (vap->iv_ps_sta || avp->av_mcastq.axq_depth)) {
                txq = &avp->av_mcastq;
                /*
                 * Mark the frame as eventually belonging on the CAB
                 * queue, so the descriptor setup functions will
                 * correctly initialise the descriptor 'qcuId' field.
                 */
                bf->bf_state.bfs_tx_queue = sc->sc_cabq->axq_qnum;
        }
#endif

        /* Do the generic frame setup */
        /* XXX should just bzero the bf_state? */
        bf->bf_state.bfs_dobaw = 0;

        /* A-MPDU TX? Manually set sequence number */
        /*
         * Don't do it whilst pending; the net80211 layer still
         * assigns them.
         */
        if (is_ampdu_tx) {
                /*
                 * Always call; this function will
                 * handle making sure that null data frames
                 * don't get a sequence number from the current
                 * TID and thus mess with the BAW.
                 */
                seqno = ath_tx_tid_seqno_assign(sc, ni, bf, m0);

                /*
                 * Don't add QoS NULL frames to the BAW.
                 */
                if (IEEE80211_QOS_HAS_SEQ(wh) &&
                    subtype != IEEE80211_FC0_SUBTYPE_QOS_NULL) {
                        bf->bf_state.bfs_dobaw = 1;
                }
        }

        /*
         * If needed, the sequence number has been assigned.
         * Squirrel it away somewhere easy to get to.
         */
        bf->bf_state.bfs_seqno = M_SEQNO_GET(m0) << IEEE80211_SEQ_SEQ_SHIFT;

        /* Is ampdu pending? fetch the seqno and print it out */
        if (is_ampdu_pending)
                DPRINTF(sc, ATH_DEBUG_SW_TX,
                    "%s: tid %d: ampdu pending, seqno %d\n",
                    __func__, tid, M_SEQNO_GET(m0));

        /* This also sets up the DMA map */
        r = ath_tx_normal_setup(sc, ni, bf, m0, txq);

        if (r != 0)
                goto done;

        /* At this point m0 could have changed! */
        m0 = bf->bf_m;

#if 1
        /*
         * If it's a multicast frame, do a direct-dispatch to the
         * destination hardware queue. Don't bother software
         * queuing it.
         */
        /*
         * If it's a BAR frame, do a direct dispatch to the
         * destination hardware queue. Don't bother software
         * queuing it, as the TID will now be paused.
         * Sending a BAR frame can occur from the net80211 txa timer
         * (ie, retries) or from the ath txtask (completion call.)
         * It queues directly to hardware because the TID is paused
         * at this point (and won't be unpaused until the BAR has
         * either been TXed successfully or max retries has been
         * reached.)
         */
        /*
         * Until things are better debugged - if this node is asleep
         * and we're sending it a non-BAR frame, direct dispatch it.
         * Why? Because we need to figure out what's actually being
         * sent - eg, during reassociation/reauthentication after
         * the node (last) disappeared whilst asleep, the driver should
         * have unpaused/unsleep'ed the node.  So until that is
         * sorted out, use this workaround.
         */
        if (txq == &avp->av_mcastq) {
                DPRINTF(sc, ATH_DEBUG_SW_TX,
                    "%s: bf=%p: mcastq: TX'ing\n", __func__, bf);
                bf->bf_state.bfs_txflags |= HAL_TXDESC_CLRDMASK;
                ath_tx_xmit_normal(sc, txq, bf);
        } else if (ath_tx_should_swq_frame(sc, ATH_NODE(ni), m0,
            &queue_to_head)) {
                ath_tx_swq(sc, ni, txq, queue_to_head, bf);
        } else {
                bf->bf_state.bfs_txflags |= HAL_TXDESC_CLRDMASK;
                ath_tx_xmit_normal(sc, txq, bf);
        }
#else
        /*
         * For now, since there's no software queue,
         * direct-dispatch to the hardware.
         */
        bf->bf_state.bfs_txflags |= HAL_TXDESC_CLRDMASK;
        /*
         * Update the current leak count if
         * we're leaking frames; and set the
         * MORE flag as appropriate.
         */
        ath_tx_leak_count_update(sc, tid, bf);
        ath_tx_xmit_normal(sc, txq, bf);
#endif
done:
        return 0;
}

static int
ath_tx_raw_start(struct ath_softc *sc, struct ieee80211_node *ni,
        struct ath_buf *bf, struct mbuf *m0,
        const struct ieee80211_bpf_params *params)
{
        struct ifnet *ifp = sc->sc_ifp;
        struct ieee80211com *ic = ifp->if_l2com;
        struct ath_hal *ah = sc->sc_ah;
        struct ieee80211vap *vap = ni->ni_vap;
        int error, ismcast, ismrr;
        int keyix, hdrlen, pktlen, try0, txantenna;
        u_int8_t rix, txrate;
        struct ieee80211_frame *wh;
        u_int flags;
        HAL_PKT_TYPE atype;
        const HAL_RATE_TABLE *rt;
        struct ath_desc *ds;
        u_int pri;
        int o_tid = -1;
        int do_override;
        uint8_t type, subtype;
        int queue_to_head;

        ATH_TX_LOCK_ASSERT(sc);

        wh = mtod(m0, struct ieee80211_frame *);
        ismcast = IEEE80211_IS_MULTICAST(wh->i_addr1);
        hdrlen = ieee80211_anyhdrsize(wh);
        /*
         * Packet length must not include any
         * pad bytes; deduct them here.
         */
        /* XXX honor IEEE80211_BPF_DATAPAD */
        pktlen = m0->m_pkthdr.len - (hdrlen & 3) + IEEE80211_CRC_LEN;

        type = wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK;
        subtype = wh->i_fc[0] & IEEE80211_FC0_SUBTYPE_MASK;

        ATH_KTR(sc, ATH_KTR_TX, 2,
             "ath_tx_raw_start: ni=%p, bf=%p, raw", ni, bf);

        DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: ismcast=%d\n",
            __func__, ismcast);

        pri = params->ibp_pri & 3;
        /* Override pri if the frame isn't a QoS one */
        if (! IEEE80211_QOS_HAS_SEQ(wh))
                pri = ath_tx_getac(sc, m0);

        /* XXX If it's an ADDBA, override the correct queue */
        do_override = ath_tx_action_frame_override_queue(sc, ni, m0, &o_tid);

        /* Map ADDBA to the correct priority */
        if (do_override) {
#if 0
                DPRINTF(sc, ATH_DEBUG_XMIT, 
                    "%s: overriding tid %d pri %d -> %d\n",
                    __func__, o_tid, pri, TID_TO_WME_AC(o_tid));
#endif
                pri = TID_TO_WME_AC(o_tid);
        }

        /* Handle encryption twiddling if needed */
        if (! ath_tx_tag_crypto(sc, ni,
            m0, params->ibp_flags & IEEE80211_BPF_CRYPTO, 0,
            &hdrlen, &pktlen, &keyix)) {
                ath_freetx(m0);
                return EIO;
        }
        /* packet header may have moved, reset our local pointer */
        wh = mtod(m0, struct ieee80211_frame *);

        /* Do the generic frame setup */
        /* XXX should just bzero the bf_state? */
        bf->bf_state.bfs_dobaw = 0;

        error = ath_tx_dmasetup(sc, bf, m0);
        if (error != 0)
                return error;
        m0 = bf->bf_m;                          /* NB: may have changed */
        wh = mtod(m0, struct ieee80211_frame *);
        bf->bf_node = ni;                       /* NB: held reference */

        /* Always enable CLRDMASK for raw frames for now.. */
        flags = HAL_TXDESC_CLRDMASK;            /* XXX needed for crypto errs */
        flags |= HAL_TXDESC_INTREQ;             /* force interrupt */
        if (params->ibp_flags & IEEE80211_BPF_RTS)
                flags |= HAL_TXDESC_RTSENA;
        else if (params->ibp_flags & IEEE80211_BPF_CTS) {
                /* XXX assume 11g/11n protection? */
                bf->bf_state.bfs_doprot = 1;
                flags |= HAL_TXDESC_CTSENA;
        }
        /* XXX leave ismcast to injector? */
        if ((params->ibp_flags & IEEE80211_BPF_NOACK) || ismcast)
                flags |= HAL_TXDESC_NOACK;

        rt = sc->sc_currates;
        KASSERT(rt != NULL, ("no rate table, mode %u", sc->sc_curmode));
        rix = ath_tx_findrix(sc, params->ibp_rate0);
        txrate = rt->info[rix].rateCode;
        if (params->ibp_flags & IEEE80211_BPF_SHORTPRE)
                txrate |= rt->info[rix].shortPreamble;
        sc->sc_txrix = rix;
        try0 = params->ibp_try0;
        ismrr = (params->ibp_try1 != 0);
        txantenna = params->ibp_pri >> 2;
        if (txantenna == 0)                     /* XXX? */
                txantenna = sc->sc_txantenna;

        /*
         * Since ctsrate is fixed, store it away for later
         * use when the descriptor fields are being set.
         */
        if (flags & (HAL_TXDESC_RTSENA|HAL_TXDESC_CTSENA))
                bf->bf_state.bfs_ctsrate0 = params->ibp_ctsrate;

        /*
         * NB: we mark all packets as type PSPOLL so the h/w won't
         * set the sequence number, duration, etc.
         */
        atype = HAL_PKT_TYPE_PSPOLL;

        if (IFF_DUMPPKTS(sc, ATH_DEBUG_XMIT))
                ieee80211_dump_pkt(ic, mtod(m0, caddr_t), m0->m_len,
                    sc->sc_hwmap[rix].ieeerate, -1);

        if (ieee80211_radiotap_active_vap(vap)) {
                u_int64_t tsf = ath_hal_gettsf64(ah);

                sc->sc_tx_th.wt_tsf = htole64(tsf);
                sc->sc_tx_th.wt_flags = sc->sc_hwmap[rix].txflags;
                if (wh->i_fc[1] & IEEE80211_FC1_WEP)
                        sc->sc_tx_th.wt_flags |= IEEE80211_RADIOTAP_F_WEP;
                if (m0->m_flags & M_FRAG)
                        sc->sc_tx_th.wt_flags |= IEEE80211_RADIOTAP_F_FRAG;
                sc->sc_tx_th.wt_rate = sc->sc_hwmap[rix].ieeerate;
                sc->sc_tx_th.wt_txpower = MIN(params->ibp_power,
                    ieee80211_get_node_txpower(ni));
                sc->sc_tx_th.wt_antenna = sc->sc_txantenna;

                ieee80211_radiotap_tx(vap, m0);
        }

        /*
         * Formulate first tx descriptor with tx controls.
         */
        ds = bf->bf_desc;
        /* XXX check return value? */

        /* Store the decided rate index values away */
        bf->bf_state.bfs_pktlen = pktlen;
        bf->bf_state.bfs_hdrlen = hdrlen;
        bf->bf_state.bfs_atype = atype;
        bf->bf_state.bfs_txpower = MIN(params->ibp_power,
            ieee80211_get_node_txpower(ni));
        bf->bf_state.bfs_txrate0 = txrate;
        bf->bf_state.bfs_try0 = try0;
        bf->bf_state.bfs_keyix = keyix;
        bf->bf_state.bfs_txantenna = txantenna;
        bf->bf_state.bfs_txflags = flags;
        bf->bf_state.bfs_shpream =
            !! (params->ibp_flags & IEEE80211_BPF_SHORTPRE);

        /* Set local packet state, used to queue packets to hardware */
        bf->bf_state.bfs_tid = WME_AC_TO_TID(pri);
        bf->bf_state.bfs_tx_queue = sc->sc_ac2q[pri]->axq_qnum;
        bf->bf_state.bfs_pri = pri;

        /* XXX this should be done in ath_tx_setrate() */
        bf->bf_state.bfs_ctsrate = 0;
        bf->bf_state.bfs_ctsduration = 0;
        bf->bf_state.bfs_ismrr = ismrr;

        /* Blank the legacy rate array */
        bzero(&bf->bf_state.bfs_rc, sizeof(bf->bf_state.bfs_rc));

        bf->bf_state.bfs_rc[0].rix =
            ath_tx_findrix(sc, params->ibp_rate0);
        bf->bf_state.bfs_rc[0].tries = try0;
        bf->bf_state.bfs_rc[0].ratecode = txrate;

        if (ismrr) {
                int rix;

                rix = ath_tx_findrix(sc, params->ibp_rate1);
                bf->bf_state.bfs_rc[1].rix = rix;
                bf->bf_state.bfs_rc[1].tries = params->ibp_try1;

                rix = ath_tx_findrix(sc, params->ibp_rate2);
                bf->bf_state.bfs_rc[2].rix = rix;
                bf->bf_state.bfs_rc[2].tries = params->ibp_try2;

                rix = ath_tx_findrix(sc, params->ibp_rate3);
                bf->bf_state.bfs_rc[3].rix = rix;
                bf->bf_state.bfs_rc[3].tries = params->ibp_try3;
        }
        /*
         * All the required rate control decisions have been made;
         * fill in the rc flags.
         */
        ath_tx_rate_fill_rcflags(sc, bf);

        /* NB: no buffered multicast in power save support */

        /*
         * If we're overiding the ADDBA destination, dump directly
         * into the hardware queue, right after any pending
         * frames to that node are.
         */
        DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: dooverride=%d\n",
            __func__, do_override);

#if 1
        /*
         * Put addba frames in the right place in the right TID/HWQ.
         */
        if (do_override) {
                bf->bf_state.bfs_txflags |= HAL_TXDESC_CLRDMASK;
                /*
                 * XXX if it's addba frames, should we be leaking
                 * them out via the frame leak method?
                 * XXX for now let's not risk it; but we may wish
                 * to investigate this later.
                 */
                ath_tx_xmit_normal(sc, sc->sc_ac2q[pri], bf);
        } else if (ath_tx_should_swq_frame(sc, ATH_NODE(ni), m0,
            &queue_to_head)) {
                /* Queue to software queue */
                ath_tx_swq(sc, ni, sc->sc_ac2q[pri], queue_to_head, bf);
        } else {
                bf->bf_state.bfs_txflags |= HAL_TXDESC_CLRDMASK;
                ath_tx_xmit_normal(sc, sc->sc_ac2q[pri], bf);
        }
#else
        /* Direct-dispatch to the hardware */
        bf->bf_state.bfs_txflags |= HAL_TXDESC_CLRDMASK;
        /*
         * Update the current leak count if
         * we're leaking frames; and set the
         * MORE flag as appropriate.
         */
        ath_tx_leak_count_update(sc, tid, bf);
        ath_tx_xmit_normal(sc, sc->sc_ac2q[pri], bf);
#endif
        return 0;
}

/*
 * Send a raw frame.
 *
 * This can be called by net80211.
 */
int
ath_raw_xmit(struct ieee80211_node *ni, struct mbuf *m,
        const struct ieee80211_bpf_params *params)
{
        struct ieee80211com *ic = ni->ni_ic;
        struct ifnet *ifp = ic->ic_ifp;
        struct ath_softc *sc = ifp->if_softc;
        struct ath_buf *bf;
        struct ieee80211_frame *wh = mtod(m, struct ieee80211_frame *);
        int error = 0;

        ATH_PCU_LOCK(sc);
        if (sc->sc_inreset_cnt > 0) {
                DPRINTF(sc, ATH_DEBUG_XMIT, 
                    "%s: sc_inreset_cnt > 0; bailing\n", __func__);
                error = EIO;
                ATH_PCU_UNLOCK(sc);
                goto bad0;
        }
        sc->sc_txstart_cnt++;
        ATH_PCU_UNLOCK(sc);

        ATH_TX_LOCK(sc);

        if ((ifp->if_drv_flags & IFF_DRV_RUNNING) == 0 || sc->sc_invalid) {
                DPRINTF(sc, ATH_DEBUG_XMIT, "%s: discard frame, %s", __func__,
                    (ifp->if_drv_flags & IFF_DRV_RUNNING) == 0 ?
                        "!running" : "invalid");
                m_freem(m);
                error = ENETDOWN;
                goto bad;
        }

        /*
         * Enforce how deep the multicast queue can grow.
         *
         * XXX duplicated in ath_tx_start().
         */
        if (IEEE80211_IS_MULTICAST(wh->i_addr1)) {
                if (sc->sc_cabq->axq_depth + sc->sc_cabq->fifo.axq_depth
                    > sc->sc_txq_mcastq_maxdepth) {
                        sc->sc_stats.ast_tx_mcastq_overflow++;
                        error = ENOBUFS;
                }

                if (error != 0) {
                        m_freem(m);
                        goto bad;
                }
        }

        /*
         * Grab a TX buffer and associated resources.
         */
        bf = ath_getbuf(sc, ATH_BUFTYPE_MGMT);
        if (bf == NULL) {
                sc->sc_stats.ast_tx_nobuf++;
                m_freem(m);
                error = ENOBUFS;
                goto bad;
        }
        ATH_KTR(sc, ATH_KTR_TX, 3, "ath_raw_xmit: m=%p, params=%p, bf=%p\n",
            m, params,  bf);

        if (params == NULL) {
                /*
                 * Legacy path; interpret frame contents to decide
                 * precisely how to send the frame.
                 */
                if (ath_tx_start(sc, ni, bf, m)) {
                        error = EIO;            /* XXX */
                        goto bad2;
                }
        } else {
                /*
                 * Caller supplied explicit parameters to use in
                 * sending the frame.
                 */
                if (ath_tx_raw_start(sc, ni, bf, m, params)) {
                        error = EIO;            /* XXX */
                        goto bad2;
                }
        }
        sc->sc_wd_timer = 5;
        ifp->if_opackets++;
        sc->sc_stats.ast_tx_raw++;

        /*
         * Update the TIM - if there's anything queued to the
         * software queue and power save is enabled, we should
         * set the TIM.
         */
        ath_tx_update_tim(sc, ni, 1);

        ATH_TX_UNLOCK(sc);

        ATH_PCU_LOCK(sc);
        sc->sc_txstart_cnt--;
        ATH_PCU_UNLOCK(sc);

        return 0;
bad2:
        ATH_KTR(sc, ATH_KTR_TX, 3, "ath_raw_xmit: bad2: m=%p, params=%p, "
            "bf=%p",
            m,
            params,
            bf);
        ATH_TXBUF_LOCK(sc);
        ath_returnbuf_head(sc, bf);
        ATH_TXBUF_UNLOCK(sc);
bad:

        ATH_TX_UNLOCK(sc);

        ATH_PCU_LOCK(sc);
        sc->sc_txstart_cnt--;
        ATH_PCU_UNLOCK(sc);
bad0:
        ATH_KTR(sc, ATH_KTR_TX, 2, "ath_raw_xmit: bad0: m=%p, params=%p",
            m, params);
        ifp->if_oerrors++;
        sc->sc_stats.ast_tx_raw_fail++;
        ieee80211_free_node(ni);

        return error;
}

/* Some helper functions */

/*
 * ADDBA (and potentially others) need to be placed in the same
 * hardware queue as the TID/node it's relating to. This is so
 * it goes out after any pending non-aggregate frames to the
 * same node/TID.
 *
 * If this isn't done, the ADDBA can go out before the frames
 * queued in hardware. Even though these frames have a sequence
 * number -earlier- than the ADDBA can be transmitted (but
 * no frames whose sequence numbers are after the ADDBA should
 * be!) they'll arrive after the ADDBA - and the receiving end
 * will simply drop them as being out of the BAW.
 *
 * The frames can't be appended to the TID software queue - it'll
 * never be sent out. So these frames have to be directly
 * dispatched to the hardware, rather than queued in software.
 * So if this function returns true, the TXQ has to be
 * overridden and it has to be directly dispatched.
 *
 * It's a dirty hack, but someone's gotta do it.
 */

/*
 * XXX doesn't belong here!
 */
static int
ieee80211_is_action(struct ieee80211_frame *wh)
{
        /* Type: Management frame? */
        if ((wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK) !=
            IEEE80211_FC0_TYPE_MGT)
                return 0;

        /* Subtype: Action frame? */
        if ((wh->i_fc[0] & IEEE80211_FC0_SUBTYPE_MASK) !=
            IEEE80211_FC0_SUBTYPE_ACTION)
                return 0;

        return 1;
}

#define MS(_v, _f)      (((_v) & _f) >> _f##_S)
/*
 * Return an alternate TID for ADDBA request frames.
 *
 * Yes, this likely should be done in the net80211 layer.
 */
static int
ath_tx_action_frame_override_queue(struct ath_softc *sc,
    struct ieee80211_node *ni,
    struct mbuf *m0, int *tid)
{
        struct ieee80211_frame *wh = mtod(m0, struct ieee80211_frame *);
        struct ieee80211_action_ba_addbarequest *ia;
        uint8_t *frm;
        uint16_t baparamset;

        /* Not action frame? Bail */
        if (! ieee80211_is_action(wh))
                return 0;

        /* XXX Not needed for frames we send? */
#if 0
        /* Correct length? */
        if (! ieee80211_parse_action(ni, m))
                return 0;
#endif

        /* Extract out action frame */
        frm = (u_int8_t *)&wh[1];
        ia = (struct ieee80211_action_ba_addbarequest *) frm;

        /* Not ADDBA? Bail */
        if (ia->rq_header.ia_category != IEEE80211_ACTION_CAT_BA)
                return 0;
        if (ia->rq_header.ia_action != IEEE80211_ACTION_BA_ADDBA_REQUEST)
                return 0;

        /* Extract TID, return it */
        baparamset = le16toh(ia->rq_baparamset);
        *tid = (int) MS(baparamset, IEEE80211_BAPS_TID);

        return 1;
}
#undef  MS

/* Per-node software queue operations */

/*
 * Add the current packet to the given BAW.
 * It is assumed that the current packet
 *
 * + fits inside the BAW;
 * + already has had a sequence number allocated.
 *
 * Since the BAW status may be modified by both the ath task and
 * the net80211/ifnet contexts, the TID must be locked.
 */
void
ath_tx_addto_baw(struct ath_softc *sc, struct ath_node *an,
    struct ath_tid *tid, struct ath_buf *bf)
{
        int index, cindex;
        struct ieee80211_tx_ampdu *tap;

        ATH_TX_LOCK_ASSERT(sc);

        if (bf->bf_state.bfs_isretried)
                return;

        tap = ath_tx_get_tx_tid(an, tid->tid);

        if (! bf->bf_state.bfs_dobaw) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
                    "%s: dobaw=0, seqno=%d, window %d:%d\n",
                    __func__, SEQNO(bf->bf_state.bfs_seqno),
                    tap->txa_start, tap->txa_wnd);
        }

        if (bf->bf_state.bfs_addedbaw)
                DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
                    "%s: re-added? tid=%d, seqno %d; window %d:%d; "
                    "baw head=%d tail=%d\n",
                    __func__, tid->tid, SEQNO(bf->bf_state.bfs_seqno),
                    tap->txa_start, tap->txa_wnd, tid->baw_head,
                    tid->baw_tail);

        /*
         * Verify that the given sequence number is not outside of the
         * BAW.  Complain loudly if that's the case.
         */
        if (! BAW_WITHIN(tap->txa_start, tap->txa_wnd,
            SEQNO(bf->bf_state.bfs_seqno))) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
                    "%s: bf=%p: outside of BAW?? tid=%d, seqno %d; window %d:%d; "
                    "baw head=%d tail=%d\n",
                    __func__, bf, tid->tid, SEQNO(bf->bf_state.bfs_seqno),
                    tap->txa_start, tap->txa_wnd, tid->baw_head,
                    tid->baw_tail);
        }

        /*
         * ni->ni_txseqs[] is the currently allocated seqno.
         * the txa state contains the current baw start.
         */
        index  = ATH_BA_INDEX(tap->txa_start, SEQNO(bf->bf_state.bfs_seqno));
        cindex = (tid->baw_head + index) & (ATH_TID_MAX_BUFS - 1);
        DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
            "%s: tid=%d, seqno %d; window %d:%d; index=%d cindex=%d "
            "baw head=%d tail=%d\n",
            __func__, tid->tid, SEQNO(bf->bf_state.bfs_seqno),
            tap->txa_start, tap->txa_wnd, index, cindex, tid->baw_head,
            tid->baw_tail);


#if 0
        assert(tid->tx_buf[cindex] == NULL);
#endif
        if (tid->tx_buf[cindex] != NULL) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
                    "%s: ba packet dup (index=%d, cindex=%d, "
                    "head=%d, tail=%d)\n",
                    __func__, index, cindex, tid->baw_head, tid->baw_tail);
                DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
                    "%s: BA bf: %p; seqno=%d ; new bf: %p; seqno=%d\n",
                    __func__,
                    tid->tx_buf[cindex],
                    SEQNO(tid->tx_buf[cindex]->bf_state.bfs_seqno),
                    bf,
                    SEQNO(bf->bf_state.bfs_seqno)
                );
        }
        tid->tx_buf[cindex] = bf;

        if (index >= ((tid->baw_tail - tid->baw_head) &
            (ATH_TID_MAX_BUFS - 1))) {
                tid->baw_tail = cindex;
                INCR(tid->baw_tail, ATH_TID_MAX_BUFS);
        }
}

/*
 * Flip the BAW buffer entry over from the existing one to the new one.
 *
 * When software retransmitting a (sub-)frame, it is entirely possible that
 * the frame ath_buf is marked as BUSY and can't be immediately reused.
 * In that instance the buffer is cloned and the new buffer is used for
 * retransmit. We thus need to update the ath_buf slot in the BAW buf
 * tracking array to maintain consistency.
 */
static void
ath_tx_switch_baw_buf(struct ath_softc *sc, struct ath_node *an,
    struct ath_tid *tid, struct ath_buf *old_bf, struct ath_buf *new_bf)
{
        int index, cindex;
        struct ieee80211_tx_ampdu *tap;
        int seqno = SEQNO(old_bf->bf_state.bfs_seqno);

        ATH_TX_LOCK_ASSERT(sc);

        tap = ath_tx_get_tx_tid(an, tid->tid);
        index  = ATH_BA_INDEX(tap->txa_start, seqno);
        cindex = (tid->baw_head + index) & (ATH_TID_MAX_BUFS - 1);

        /*
         * Just warn for now; if it happens then we should find out
         * about it. It's highly likely the aggregation session will
         * soon hang.
         */
        if (old_bf->bf_state.bfs_seqno != new_bf->bf_state.bfs_seqno) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
                    "%s: retransmitted buffer"
                    " has mismatching seqno's, BA session may hang.\n",
                    __func__);
                DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
                    "%s: old seqno=%d, new_seqno=%d\n", __func__,
                    old_bf->bf_state.bfs_seqno, new_bf->bf_state.bfs_seqno);
        }

        if (tid->tx_buf[cindex] != old_bf) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
                    "%s: ath_buf pointer incorrect; "
                    " has m BA session may hang.\n", __func__);
                DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
                    "%s: old bf=%p, new bf=%p\n", __func__, old_bf, new_bf);
        }

        tid->tx_buf[cindex] = new_bf;
}

/*
 * seq_start - left edge of BAW
 * seq_next - current/next sequence number to allocate
 *
 * Since the BAW status may be modified by both the ath task and
 * the net80211/ifnet contexts, the TID must be locked.
 */
static void
ath_tx_update_baw(struct ath_softc *sc, struct ath_node *an,
    struct ath_tid *tid, const struct ath_buf *bf)
{
        int index, cindex;
        struct ieee80211_tx_ampdu *tap;
        int seqno = SEQNO(bf->bf_state.bfs_seqno);

        ATH_TX_LOCK_ASSERT(sc);

        tap = ath_tx_get_tx_tid(an, tid->tid);
        index  = ATH_BA_INDEX(tap->txa_start, seqno);
        cindex = (tid->baw_head + index) & (ATH_TID_MAX_BUFS - 1);

        DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
            "%s: tid=%d, baw=%d:%d, seqno=%d, index=%d, cindex=%d, "
            "baw head=%d, tail=%d\n",
            __func__, tid->tid, tap->txa_start, tap->txa_wnd, seqno, index,
            cindex, tid->baw_head, tid->baw_tail);

        /*
         * If this occurs then we have a big problem - something else
         * has slid tap->txa_start along without updating the BAW
         * tracking start/end pointers. Thus the TX BAW state is now
         * completely busted.
         *
         * But for now, since I haven't yet fixed TDMA and buffer cloning,
         * it's quite possible that a cloned buffer is making its way
         * here and causing it to fire off. Disable TDMA for now.
         */
        if (tid->tx_buf[cindex] != bf) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
                    "%s: comp bf=%p, seq=%d; slot bf=%p, seqno=%d\n",
                    __func__, bf, SEQNO(bf->bf_state.bfs_seqno),
                    tid->tx_buf[cindex],
                    (tid->tx_buf[cindex] != NULL) ?
                      SEQNO(tid->tx_buf[cindex]->bf_state.bfs_seqno) : -1);
        }

        tid->tx_buf[cindex] = NULL;

        while (tid->baw_head != tid->baw_tail &&
            !tid->tx_buf[tid->baw_head]) {
                INCR(tap->txa_start, IEEE80211_SEQ_RANGE);
                INCR(tid->baw_head, ATH_TID_MAX_BUFS);
        }
        DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
            "%s: baw is now %d:%d, baw head=%d\n",
            __func__, tap->txa_start, tap->txa_wnd, tid->baw_head);
}

static void
ath_tx_leak_count_update(struct ath_softc *sc, struct ath_tid *tid,
    struct ath_buf *bf)
{
        struct ieee80211_frame *wh;

        ATH_TX_LOCK_ASSERT(sc);

        if (tid->an->an_leak_count > 0) {
                wh = mtod(bf->bf_m, struct ieee80211_frame *);

                /*
                 * Update MORE based on the software/net80211 queue states.
                 */
                if ((tid->an->an_stack_psq > 0)
                    || (tid->an->an_swq_depth > 0))
                        wh->i_fc[1] |= IEEE80211_FC1_MORE_DATA;
                else
                        wh->i_fc[1] &= ~IEEE80211_FC1_MORE_DATA;

                DPRINTF(sc, ATH_DEBUG_NODE_PWRSAVE,
                    "%s: %6D: leak count = %d, psq=%d, swq=%d, MORE=%d\n",
                    __func__,
                    tid->an->an_node.ni_macaddr,
                    ":",
                    tid->an->an_leak_count,
                    tid->an->an_stack_psq,
                    tid->an->an_swq_depth,
                    !! (wh->i_fc[1] & IEEE80211_FC1_MORE_DATA));

                /*
                 * Re-sync the underlying buffer.
                 */
                bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap,
                    BUS_DMASYNC_PREWRITE);

                tid->an->an_leak_count --;
        }
}

static int
ath_tx_tid_can_tx_or_sched(struct ath_softc *sc, struct ath_tid *tid)
{

        ATH_TX_LOCK_ASSERT(sc);

        if (tid->an->an_leak_count > 0) {
                return (1);
        }
        if (tid->paused)
                return (0);
        return (1);
}

/*
 * Mark the current node/TID as ready to TX.
 *
 * This is done to make it easy for the software scheduler to
 * find which nodes have data to send.
 *
 * The TXQ lock must be held.
 */
void
ath_tx_tid_sched(struct ath_softc *sc, struct ath_tid *tid)
{
        struct ath_txq *txq = sc->sc_ac2q[tid->ac];

        ATH_TX_LOCK_ASSERT(sc);

        /*
         * If we are leaking out a frame to this destination
         * for PS-POLL, ensure that we allow scheduling to
         * occur.
         */
        if (! ath_tx_tid_can_tx_or_sched(sc, tid))
                return;         /* paused, can't schedule yet */

        if (tid->sched)
                return;         /* already scheduled */

        tid->sched = 1;

#if 0
        /*
         * If this is a sleeping node we're leaking to, given
         * it a higher priority.  This is so bad for QoS it hurts.
         */
        if (tid->an->an_leak_count) {
                TAILQ_INSERT_HEAD(&txq->axq_tidq, tid, axq_qelem);
        } else {
                TAILQ_INSERT_TAIL(&txq->axq_tidq, tid, axq_qelem);
        }
#endif

        /*
         * We can't do the above - it'll confuse the TXQ software
         * scheduler which will keep checking the _head_ TID
         * in the list to see if it has traffic.  If we queue
         * a TID to the head of the list and it doesn't transmit,
         * we'll check it again.
         *
         * So, get the rest of this leaking frames support working
         * and reliable first and _then_ optimise it so they're
         * pushed out in front of any other pending software
         * queued nodes.
         */
        TAILQ_INSERT_TAIL(&txq->axq_tidq, tid, axq_qelem);
}

/*
 * Mark the current node as no longer needing to be polled for
 * TX packets.
 *
 * The TXQ lock must be held.
 */
static void
ath_tx_tid_unsched(struct ath_softc *sc, struct ath_tid *tid)
{
        struct ath_txq *txq = sc->sc_ac2q[tid->ac];

        ATH_TX_LOCK_ASSERT(sc);

        if (tid->sched == 0)
                return;

        tid->sched = 0;
        TAILQ_REMOVE(&txq->axq_tidq, tid, axq_qelem);
}

/*
 * Assign a sequence number manually to the given frame.
 *
 * This should only be called for A-MPDU TX frames.
 */
static ieee80211_seq
ath_tx_tid_seqno_assign(struct ath_softc *sc, struct ieee80211_node *ni,
    struct ath_buf *bf, struct mbuf *m0)
{
        struct ieee80211_frame *wh;
        int tid, pri;
        ieee80211_seq seqno;
        uint8_t subtype;

        /* TID lookup */
        wh = mtod(m0, struct ieee80211_frame *);
        pri = M_WME_GETAC(m0);                  /* honor classification */
        tid = WME_AC_TO_TID(pri);
        DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: pri=%d, tid=%d, qos has seq=%d\n",
            __func__, pri, tid, IEEE80211_QOS_HAS_SEQ(wh));

        /* XXX Is it a control frame? Ignore */

        /* Does the packet require a sequence number? */
        if (! IEEE80211_QOS_HAS_SEQ(wh))
                return -1;

        ATH_TX_LOCK_ASSERT(sc);

        /*
         * Is it a QOS NULL Data frame? Give it a sequence number from
         * the default TID (IEEE80211_NONQOS_TID.)
         *
         * The RX path of everything I've looked at doesn't include the NULL
         * data frame sequence number in the aggregation state updates, so
         * assigning it a sequence number there will cause a BAW hole on the
         * RX side.
         */
        subtype = wh->i_fc[0] & IEEE80211_FC0_SUBTYPE_MASK;
        if (subtype == IEEE80211_FC0_SUBTYPE_QOS_NULL) {
                /* XXX no locking for this TID? This is a bit of a problem. */
                seqno = ni->ni_txseqs[IEEE80211_NONQOS_TID];
                INCR(ni->ni_txseqs[IEEE80211_NONQOS_TID], IEEE80211_SEQ_RANGE);
        } else {
                /* Manually assign sequence number */
                seqno = ni->ni_txseqs[tid];
                INCR(ni->ni_txseqs[tid], IEEE80211_SEQ_RANGE);
        }
        *(uint16_t *)&wh->i_seq[0] = htole16(seqno << IEEE80211_SEQ_SEQ_SHIFT);
        M_SEQNO_SET(m0, seqno);

        /* Return so caller can do something with it if needed */
        DPRINTF(sc, ATH_DEBUG_SW_TX, "%s:  -> seqno=%d\n", __func__, seqno);
        return seqno;
}

/*
 * Attempt to direct dispatch an aggregate frame to hardware.
 * If the frame is out of BAW, queue.
 * Otherwise, schedule it as a single frame.
 */
static void
ath_tx_xmit_aggr(struct ath_softc *sc, struct ath_node *an,
    struct ath_txq *txq, struct ath_buf *bf)
{
        struct ath_tid *tid = &an->an_tid[bf->bf_state.bfs_tid];
        struct ieee80211_tx_ampdu *tap;

        ATH_TX_LOCK_ASSERT(sc);

        tap = ath_tx_get_tx_tid(an, tid->tid);

        /* paused? queue */
        if (! ath_tx_tid_can_tx_or_sched(sc, tid)) {
                ATH_TID_INSERT_HEAD(tid, bf, bf_list);
                /* XXX don't sched - we're paused! */
                return;
        }

        /* outside baw? queue */
        if (bf->bf_state.bfs_dobaw &&
            (! BAW_WITHIN(tap->txa_start, tap->txa_wnd,
            SEQNO(bf->bf_state.bfs_seqno)))) {
                ATH_TID_INSERT_HEAD(tid, bf, bf_list);
                ath_tx_tid_sched(sc, tid);
                return;
        }

        /*
         * This is a temporary check and should be removed once
         * all the relevant code paths have been fixed.
         *
         * During aggregate retries, it's possible that the head
         * frame will fail (which has the bfs_aggr and bfs_nframes
         * fields set for said aggregate) and will be retried as
         * a single frame.  In this instance, the values should
         * be reset or the completion code will get upset with you.
         */
        if (bf->bf_state.bfs_aggr != 0 || bf->bf_state.bfs_nframes > 1) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
                    "%s: bfs_aggr=%d, bfs_nframes=%d\n", __func__,
                    bf->bf_state.bfs_aggr, bf->bf_state.bfs_nframes);
                bf->bf_state.bfs_aggr = 0;
                bf->bf_state.bfs_nframes = 1;
        }

        /* Update CLRDMASK just before this frame is queued */
        ath_tx_update_clrdmask(sc, tid, bf);

        /* Direct dispatch to hardware */
        ath_tx_do_ratelookup(sc, bf);
        ath_tx_calc_duration(sc, bf);
        ath_tx_calc_protection(sc, bf);
        ath_tx_set_rtscts(sc, bf);
        ath_tx_rate_fill_rcflags(sc, bf);
        ath_tx_setds(sc, bf);

        /* Statistics */
        sc->sc_aggr_stats.aggr_low_hwq_single_pkt++;

        /* Track per-TID hardware queue depth correctly */
        tid->hwq_depth++;

        /* Add to BAW */
        if (bf->bf_state.bfs_dobaw) {
                ath_tx_addto_baw(sc, an, tid, bf);
                bf->bf_state.bfs_addedbaw = 1;
        }

        /* Set completion handler, multi-frame aggregate or not */
        bf->bf_comp = ath_tx_aggr_comp;

        /*
         * Update the current leak count if
         * we're leaking frames; and set the
         * MORE flag as appropriate.
         */
        ath_tx_leak_count_update(sc, tid, bf);

        /* Hand off to hardware */
        ath_tx_handoff(sc, txq, bf);
}

/*
 * Attempt to send the packet.
 * If the queue isn't busy, direct-dispatch.
 * If the queue is busy enough, queue the given packet on the
 *  relevant software queue.
 */
void
ath_tx_swq(struct ath_softc *sc, struct ieee80211_node *ni,
    struct ath_txq *txq, int queue_to_head, struct ath_buf *bf)
{
        struct ath_node *an = ATH_NODE(ni);
        struct ieee80211_frame *wh;
        struct ath_tid *atid;
        int pri, tid;
        struct mbuf *m0 = bf->bf_m;

        ATH_TX_LOCK_ASSERT(sc);

        /* Fetch the TID - non-QoS frames get assigned to TID 16 */
        wh = mtod(m0, struct ieee80211_frame *);
        pri = ath_tx_getac(sc, m0);
        tid = ath_tx_gettid(sc, m0);
        atid = &an->an_tid[tid];

        DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: bf=%p, pri=%d, tid=%d, qos=%d\n",
            __func__, bf, pri, tid, IEEE80211_QOS_HAS_SEQ(wh));

        /* Set local packet state, used to queue packets to hardware */
        /* XXX potentially duplicate info, re-check */
        bf->bf_state.bfs_tid = tid;
        bf->bf_state.bfs_tx_queue = txq->axq_qnum;
        bf->bf_state.bfs_pri = pri;

        /*
         * If the hardware queue isn't busy, queue it directly.
         * If the hardware queue is busy, queue it.
         * If the TID is paused or the traffic it outside BAW, software
         * queue it.
         *
         * If the node is in power-save and we're leaking a frame,
         * leak a single frame.
         */
        if (! ath_tx_tid_can_tx_or_sched(sc, atid)) {
                /* TID is paused, queue */
                DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: paused\n", __func__);
                /*
                 * If the caller requested that it be sent at a high
                 * priority, queue it at the head of the list.
                 */
                if (queue_to_head)
                        ATH_TID_INSERT_HEAD(atid, bf, bf_list);
                else
                        ATH_TID_INSERT_TAIL(atid, bf, bf_list);
        } else if (ath_tx_ampdu_pending(sc, an, tid)) {
                /* AMPDU pending; queue */
                DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: pending\n", __func__);
                ATH_TID_INSERT_TAIL(atid, bf, bf_list);
                /* XXX sched? */
        } else if (ath_tx_ampdu_running(sc, an, tid)) {
                /* AMPDU running, attempt direct dispatch if possible */

                /*
                 * Always queue the frame to the tail of the list.
                 */
                ATH_TID_INSERT_TAIL(atid, bf, bf_list);

                /*
                 * If the hardware queue isn't busy, direct dispatch
                 * the head frame in the list.  Don't schedule the
                 * TID - let it build some more frames first?
                 *
                 * When running A-MPDU, always just check the hardware
                 * queue depth against the aggregate frame limit.
                 * We don't want to burst a large number of single frames
                 * out to the hardware; we want to aggressively hold back.
                 *
                 * Otherwise, schedule the TID.
                 */
                /* XXX TXQ locking */
                if (txq->axq_depth + txq->fifo.axq_depth < sc->sc_hwq_limit_aggr) {
                        bf = ATH_TID_FIRST(atid);
                        ATH_TID_REMOVE(atid, bf, bf_list);

                        /*
                         * Ensure it's definitely treated as a non-AMPDU
                         * frame - this information may have been left
                         * over from a previous attempt.
                         */
                        bf->bf_state.bfs_aggr = 0;
                        bf->bf_state.bfs_nframes = 1;

                        /* Queue to the hardware */
                        ath_tx_xmit_aggr(sc, an, txq, bf);
                        DPRINTF(sc, ATH_DEBUG_SW_TX,
                            "%s: xmit_aggr\n",
                            __func__);
                } else {
                        DPRINTF(sc, ATH_DEBUG_SW_TX,
                            "%s: ampdu; swq'ing\n",
                            __func__);

                        ath_tx_tid_sched(sc, atid);
                }
        /*
         * If we're not doing A-MPDU, be prepared to direct dispatch
         * up to both limits if possible.  This particular corner
         * case may end up with packet starvation between aggregate
         * traffic and non-aggregate traffic: we wnat to ensure
         * that non-aggregate stations get a few frames queued to the
         * hardware before the aggregate station(s) get their chance.
         *
         * So if you only ever see a couple of frames direct dispatched
         * to the hardware from a non-AMPDU client, check both here
         * and in the software queue dispatcher to ensure that those
         * non-AMPDU stations get a fair chance to transmit.
         */
        /* XXX TXQ locking */
        } else if ((txq->axq_depth + txq->fifo.axq_depth < sc->sc_hwq_limit_nonaggr) &&
                    (txq->axq_aggr_depth < sc->sc_hwq_limit_aggr)) {
                /* AMPDU not running, attempt direct dispatch */
                DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: xmit_normal\n", __func__);
                /* See if clrdmask needs to be set */
                ath_tx_update_clrdmask(sc, atid, bf);

                /*
                 * Update the current leak count if
                 * we're leaking frames; and set the
                 * MORE flag as appropriate.
                 */
                ath_tx_leak_count_update(sc, atid, bf);

                /*
                 * Dispatch the frame.
                 */
                ath_tx_xmit_normal(sc, txq, bf);
        } else {
                /* Busy; queue */
                DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: swq'ing\n", __func__);
                ATH_TID_INSERT_TAIL(atid, bf, bf_list);
                ath_tx_tid_sched(sc, atid);
        }
}

/*
 * Only set the clrdmask bit if none of the nodes are currently
 * filtered.
 *
 * XXX TODO: go through all the callers and check to see
 * which are being called in the context of looping over all
 * TIDs (eg, if all tids are being paused, resumed, etc.)
 * That'll avoid O(n^2) complexity here.
 */
static void
ath_tx_set_clrdmask(struct ath_softc *sc, struct ath_node *an)
{
        int i;

        ATH_TX_LOCK_ASSERT(sc);

        for (i = 0; i < IEEE80211_TID_SIZE; i++) {
                if (an->an_tid[i].isfiltered == 1)
                        return;
        }
        an->clrdmask = 1;
}

/*
 * Configure the per-TID node state.
 *
 * This likely belongs in if_ath_node.c but I can't think of anywhere
 * else to put it just yet.
 *
 * This sets up the SLISTs and the mutex as appropriate.
 */
void
ath_tx_tid_init(struct ath_softc *sc, struct ath_node *an)
{
        int i, j;
        struct ath_tid *atid;

        for (i = 0; i < IEEE80211_TID_SIZE; i++) {
                atid = &an->an_tid[i];

                /* XXX now with this bzer(), is the field 0'ing needed? */
                bzero(atid, sizeof(*atid));

                TAILQ_INIT(&atid->tid_q);
                TAILQ_INIT(&atid->filtq.tid_q);
                atid->tid = i;
                atid->an = an;
                for (j = 0; j < ATH_TID_MAX_BUFS; j++)
                        atid->tx_buf[j] = NULL;
                atid->baw_head = atid->baw_tail = 0;
                atid->paused = 0;
                atid->sched = 0;
                atid->hwq_depth = 0;
                atid->cleanup_inprogress = 0;
                if (i == IEEE80211_NONQOS_TID)
                        atid->ac = ATH_NONQOS_TID_AC;
                else
                        atid->ac = TID_TO_WME_AC(i);
        }
        an->clrdmask = 1;       /* Always start by setting this bit */
}

/*
 * Pause the current TID. This stops packets from being transmitted
 * on it.
 *
 * Since this is also called from upper layers as well as the driver,
 * it will get the TID lock.
 */
static void
ath_tx_tid_pause(struct ath_softc *sc, struct ath_tid *tid)
{

        ATH_TX_LOCK_ASSERT(sc);
        tid->paused++;
        DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL, "%s: paused = %d\n",
            __func__, tid->paused);
}

/*
 * Unpause the current TID, and schedule it if needed.
 */
static void
ath_tx_tid_resume(struct ath_softc *sc, struct ath_tid *tid)
{
        ATH_TX_LOCK_ASSERT(sc);

        /*
         * There's some odd places where ath_tx_tid_resume() is called
         * when it shouldn't be; this works around that particular issue
         * until it's actually resolved.
         */
        if (tid->paused == 0) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL,
                    "%s: %6D: paused=0?\n", __func__,
                    tid->an->an_node.ni_macaddr, ":");
        } else {
                tid->paused--;
        }

        DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL, "%s: unpaused = %d\n",
            __func__, tid->paused);

        if (tid->paused)
                return;

        /*
         * Override the clrdmask configuration for the next frame
         * from this TID, just to get the ball rolling.
         */
        ath_tx_set_clrdmask(sc, tid->an);

        if (tid->axq_depth == 0)
                return;

        /* XXX isfiltered shouldn't ever be 0 at this point */
        if (tid->isfiltered == 1) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL, "%s: filtered?!\n",
                    __func__);
                return;
        }

        ath_tx_tid_sched(sc, tid);

        /*
         * Queue the software TX scheduler.
         */
        ath_tx_swq_kick(sc);
}

/*
 * Add the given ath_buf to the TID filtered frame list.
 * This requires the TID be filtered.
 */
static void
ath_tx_tid_filt_addbuf(struct ath_softc *sc, struct ath_tid *tid,
    struct ath_buf *bf)
{

        ATH_TX_LOCK_ASSERT(sc);

        if (!tid->isfiltered)
                DPRINTF(sc, ATH_DEBUG_SW_TX_FILT, "%s: not filtered?!\n",
                    __func__);

        DPRINTF(sc, ATH_DEBUG_SW_TX_FILT, "%s: bf=%p\n", __func__, bf);

        /* Set the retry bit and bump the retry counter */
        ath_tx_set_retry(sc, bf);
        sc->sc_stats.ast_tx_swfiltered++;

        ATH_TID_FILT_INSERT_TAIL(tid, bf, bf_list);
}

/*
 * Handle a completed filtered frame from the given TID.
 * This just enables/pauses the filtered frame state if required
 * and appends the filtered frame to the filtered queue.
 */
static void
ath_tx_tid_filt_comp_buf(struct ath_softc *sc, struct ath_tid *tid,
    struct ath_buf *bf)
{

        ATH_TX_LOCK_ASSERT(sc);

        if (! tid->isfiltered) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_FILT, "%s: filter transition\n",
                    __func__);
                tid->isfiltered = 1;
                ath_tx_tid_pause(sc, tid);
        }

        /* Add the frame to the filter queue */
        ath_tx_tid_filt_addbuf(sc, tid, bf);
}

/*
 * Complete the filtered frame TX completion.
 *
 * If there are no more frames in the hardware queue, unpause/unfilter
 * the TID if applicable.  Otherwise we will wait for a node PS transition
 * to unfilter.
 */
static void
ath_tx_tid_filt_comp_complete(struct ath_softc *sc, struct ath_tid *tid)
{
        struct ath_buf *bf;

        ATH_TX_LOCK_ASSERT(sc);

        if (tid->hwq_depth != 0)
                return;

        DPRINTF(sc, ATH_DEBUG_SW_TX_FILT, "%s: hwq=0, transition back\n",
            __func__);
        tid->isfiltered = 0;
        /* XXX ath_tx_tid_resume() also calls ath_tx_set_clrdmask()! */
        ath_tx_set_clrdmask(sc, tid->an);

        /* XXX this is really quite inefficient */
        while ((bf = ATH_TID_FILT_LAST(tid, ath_bufhead_s)) != NULL) {
                ATH_TID_FILT_REMOVE(tid, bf, bf_list);
                ATH_TID_INSERT_HEAD(tid, bf, bf_list);
        }

        ath_tx_tid_resume(sc, tid);
}

/*
 * Called when a single (aggregate or otherwise) frame is completed.
 *
 * Returns 1 if the buffer could be added to the filtered list
 * (cloned or otherwise), 0 if the buffer couldn't be added to the
 * filtered list (failed clone; expired retry) and the caller should
 * free it and handle it like a failure (eg by sending a BAR.)
 */
static int
ath_tx_tid_filt_comp_single(struct ath_softc *sc, struct ath_tid *tid,
    struct ath_buf *bf)
{
        struct ath_buf *nbf;
        int retval;

        ATH_TX_LOCK_ASSERT(sc);

        /*
         * Don't allow a filtered frame to live forever.
         */
        if (bf->bf_state.bfs_retries > SWMAX_RETRIES) {
                sc->sc_stats.ast_tx_swretrymax++;
                DPRINTF(sc, ATH_DEBUG_SW_TX_FILT,
                    "%s: bf=%p, seqno=%d, exceeded retries\n",
                    __func__,
                    bf,
                    bf->bf_state.bfs_seqno);
                return (0);
        }

        /*
         * A busy buffer can't be added to the retry list.
         * It needs to be cloned.
         */
        if (bf->bf_flags & ATH_BUF_BUSY) {
                nbf = ath_tx_retry_clone(sc, tid->an, tid, bf);
                DPRINTF(sc, ATH_DEBUG_SW_TX_FILT,
                    "%s: busy buffer clone: %p -> %p\n",
                    __func__, bf, nbf);
        } else {
                nbf = bf;
        }

        if (nbf == NULL) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_FILT,
                    "%s: busy buffer couldn't be cloned (%p)!\n",
                    __func__, bf);
                retval = 1;
        } else {
                ath_tx_tid_filt_comp_buf(sc, tid, nbf);
                retval = 0;
        }
        ath_tx_tid_filt_comp_complete(sc, tid);

        return (retval);
}

static void
ath_tx_tid_filt_comp_aggr(struct ath_softc *sc, struct ath_tid *tid,
    struct ath_buf *bf_first, ath_bufhead *bf_q)
{
        struct ath_buf *bf, *bf_next, *nbf;

        ATH_TX_LOCK_ASSERT(sc);

        bf = bf_first;
        while (bf) {
                bf_next = bf->bf_next;
                bf->bf_next = NULL;     /* Remove it from the aggr list */

                /*
                 * Don't allow a filtered frame to live forever.
                 */
                if (bf->bf_state.bfs_retries > SWMAX_RETRIES) {
                        sc->sc_stats.ast_tx_swretrymax++;
                        DPRINTF(sc, ATH_DEBUG_SW_TX_FILT,
                            "%s: bf=%p, seqno=%d, exceeded retries\n",
                            __func__,
                            bf,
                            bf->bf_state.bfs_seqno);
                        TAILQ_INSERT_TAIL(bf_q, bf, bf_list);
                        goto next;
                }

                if (bf->bf_flags & ATH_BUF_BUSY) {
                        nbf = ath_tx_retry_clone(sc, tid->an, tid, bf);
                        DPRINTF(sc, ATH_DEBUG_SW_TX_FILT,
                            "%s: busy buffer cloned: %p -> %p",
                            __func__, bf, nbf);
                } else {
                        nbf = bf;
                }

                /*
                 * If the buffer couldn't be cloned, add it to bf_q;
                 * the caller will free the buffer(s) as required.
                 */
                if (nbf == NULL) {
                        DPRINTF(sc, ATH_DEBUG_SW_TX_FILT,
                            "%s: buffer couldn't be cloned! (%p)\n",
                            __func__, bf);
                        TAILQ_INSERT_TAIL(bf_q, bf, bf_list);
                } else {
                        ath_tx_tid_filt_comp_buf(sc, tid, nbf);
                }
next:
                bf = bf_next;
        }

        ath_tx_tid_filt_comp_complete(sc, tid);
}

/*
 * Suspend the queue because we need to TX a BAR.
 */
static void
ath_tx_tid_bar_suspend(struct ath_softc *sc, struct ath_tid *tid)
{

        ATH_TX_LOCK_ASSERT(sc);

        DPRINTF(sc, ATH_DEBUG_SW_TX_BAR,
            "%s: tid=%d, bar_wait=%d, bar_tx=%d, called\n",
            __func__,
            tid->tid,
            tid->bar_wait,
            tid->bar_tx);

        /* We shouldn't be called when bar_tx is 1 */
        if (tid->bar_tx) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_BAR,
                    "%s: bar_tx is 1?!\n", __func__);
        }

        /* If we've already been called, just be patient. */
        if (tid->bar_wait)
                return;

        /* Wait! */
        tid->bar_wait = 1;

        /* Only one pause, no matter how many frames fail */
        ath_tx_tid_pause(sc, tid);
}

/*
 * We've finished with BAR handling - either we succeeded or
 * failed. Either way, unsuspend TX.
 */
static void
ath_tx_tid_bar_unsuspend(struct ath_softc *sc, struct ath_tid *tid)
{

        ATH_TX_LOCK_ASSERT(sc);

        DPRINTF(sc, ATH_DEBUG_SW_TX_BAR,
            "%s: %6D: TID=%d, called\n",
            __func__,
            tid->an->an_node.ni_macaddr,
            ":",
            tid->tid);

        if (tid->bar_tx == 0 || tid->bar_wait == 0) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_BAR,
                    "%s: %6D: TID=%d, bar_tx=%d, bar_wait=%d: ?\n",
                    __func__, tid->an->an_node.ni_macaddr, ":",
                    tid->tid, tid->bar_tx, tid->bar_wait);
        }

        tid->bar_tx = tid->bar_wait = 0;
        ath_tx_tid_resume(sc, tid);
}

/*
 * Return whether we're ready to TX a BAR frame.
 *
 * Requires the TID lock be held.
 */
static int
ath_tx_tid_bar_tx_ready(struct ath_softc *sc, struct ath_tid *tid)
{

        ATH_TX_LOCK_ASSERT(sc);

        if (tid->bar_wait == 0 || tid->hwq_depth > 0)
                return (0);

        DPRINTF(sc, ATH_DEBUG_SW_TX_BAR,
            "%s: %6D: TID=%d, bar ready\n",
            __func__,
            tid->an->an_node.ni_macaddr,
            ":",
            tid->tid);

        return (1);
}

/*
 * Check whether the current TID is ready to have a BAR
 * TXed and if so, do the TX.
 *
 * Since the TID/TXQ lock can't be held during a call to
 * ieee80211_send_bar(), we have to do the dirty thing of unlocking it,
 * sending the BAR and locking it again.
 *
 * Eventually, the code to send the BAR should be broken out
 * from this routine so the lock doesn't have to be reacquired
 * just to be immediately dropped by the caller.
 */
static void
ath_tx_tid_bar_tx(struct ath_softc *sc, struct ath_tid *tid)
{
        struct ieee80211_tx_ampdu *tap;

        ATH_TX_LOCK_ASSERT(sc);

        DPRINTF(sc, ATH_DEBUG_SW_TX_BAR,
            "%s: %6D: TID=%d, called\n",
            __func__,
            tid->an->an_node.ni_macaddr,
            ":",
            tid->tid);

        tap = ath_tx_get_tx_tid(tid->an, tid->tid);

        /*
         * This is an error condition!
         */
        if (tid->bar_wait == 0 || tid->bar_tx == 1) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_BAR,
                    "%s: %6D: TID=%d, bar_tx=%d, bar_wait=%d: ?\n",
                    __func__, tid->an->an_node.ni_macaddr, ":",
                    tid->tid, tid->bar_tx, tid->bar_wait);
                return;
        }

        /* Don't do anything if we still have pending frames */
        if (tid->hwq_depth > 0) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_BAR,
                    "%s: %6D: TID=%d, hwq_depth=%d, waiting\n",
                    __func__,
                    tid->an->an_node.ni_macaddr,
                    ":",
                    tid->tid,
                    tid->hwq_depth);
                return;
        }

        /* We're now about to TX */
        tid->bar_tx = 1;

        /*
         * Override the clrdmask configuration for the next frame,
         * just to get the ball rolling.
         */
        ath_tx_set_clrdmask(sc, tid->an);

        /*
         * Calculate new BAW left edge, now that all frames have either
         * succeeded or failed.
         *
         * XXX verify this is _actually_ the valid value to begin at!
         */
        DPRINTF(sc, ATH_DEBUG_SW_TX_BAR,
            "%s: %6D: TID=%d, new BAW left edge=%d\n",
            __func__,
            tid->an->an_node.ni_macaddr,
            ":",
            tid->tid,
            tap->txa_start);

        /* Try sending the BAR frame */
        /* We can't hold the lock here! */

        ATH_TX_UNLOCK(sc);
        if (ieee80211_send_bar(&tid->an->an_node, tap, tap->txa_start) == 0) {
                /* Success? Now we wait for notification that it's done */
                ATH_TX_LOCK(sc);
                return;
        }

        /* Failure? For now, warn loudly and continue */
        ATH_TX_LOCK(sc);
        DPRINTF(sc, ATH_DEBUG_SW_TX_BAR,
            "%s: %6D: TID=%d, failed to TX BAR, continue!\n",
            __func__, tid->an->an_node.ni_macaddr, ":",
            tid->tid);
        ath_tx_tid_bar_unsuspend(sc, tid);
}

static void
ath_tx_tid_drain_pkt(struct ath_softc *sc, struct ath_node *an,
    struct ath_tid *tid, ath_bufhead *bf_cq, struct ath_buf *bf)
{

        ATH_TX_LOCK_ASSERT(sc);

        /*
         * If the current TID is running AMPDU, update
         * the BAW.
         */
        if (ath_tx_ampdu_running(sc, an, tid->tid) &&
            bf->bf_state.bfs_dobaw) {
                /*
                 * Only remove the frame from the BAW if it's
                 * been transmitted at least once; this means
                 * the frame was in the BAW to begin with.
                 */
                if (bf->bf_state.bfs_retries > 0) {
                        ath_tx_update_baw(sc, an, tid, bf);
                        bf->bf_state.bfs_dobaw = 0;
                }
#if 0
                /*
                 * This has become a non-fatal error now
                 */
                if (! bf->bf_state.bfs_addedbaw)
                        DPRINTF(sc, ATH_DEBUG_SW_TX_BAW
                            "%s: wasn't added: seqno %d\n",
                            __func__, SEQNO(bf->bf_state.bfs_seqno));
#endif
        }

        /* Strip it out of an aggregate list if it was in one */
        bf->bf_next = NULL;

        /* Insert on the free queue to be freed by the caller */
        TAILQ_INSERT_TAIL(bf_cq, bf, bf_list);
}

static void
ath_tx_tid_drain_print(struct ath_softc *sc, struct ath_node *an,
    const char *pfx, struct ath_tid *tid, struct ath_buf *bf)
{
        struct ieee80211_node *ni = &an->an_node;
        struct ath_txq *txq;
        struct ieee80211_tx_ampdu *tap;

        txq = sc->sc_ac2q[tid->ac];
        tap = ath_tx_get_tx_tid(an, tid->tid);

        DPRINTF(sc, ATH_DEBUG_SW_TX,
            "%s: %s: %6D: bf=%p: addbaw=%d, dobaw=%d, "
            "seqno=%d, retry=%d\n",
            __func__,
            pfx,
            ni->ni_macaddr,
            ":",
            bf,
            bf->bf_state.bfs_addedbaw,
            bf->bf_state.bfs_dobaw,
            SEQNO(bf->bf_state.bfs_seqno),
            bf->bf_state.bfs_retries);
        DPRINTF(sc, ATH_DEBUG_SW_TX,
            "%s: %s: %6D: bf=%p: txq[%d] axq_depth=%d, axq_aggr_depth=%d\n",
            __func__,
            pfx,
            ni->ni_macaddr,
            ":",
            bf,
            txq->axq_qnum,
            txq->axq_depth,
            txq->axq_aggr_depth);
        DPRINTF(sc, ATH_DEBUG_SW_TX,
            "%s: %s: %6D: bf=%p: tid txq_depth=%d hwq_depth=%d, bar_wait=%d, "
              "isfiltered=%d\n",
            __func__,
            pfx,
            ni->ni_macaddr,
            ":",
            bf,
            tid->axq_depth,
            tid->hwq_depth,
            tid->bar_wait,
            tid->isfiltered);
        DPRINTF(sc, ATH_DEBUG_SW_TX,
            "%s: %s: %6D: tid %d: "
            "sched=%d, paused=%d, "
            "incomp=%d, baw_head=%d, "
            "baw_tail=%d txa_start=%d, ni_txseqs=%d\n",
             __func__,
             pfx,
             ni->ni_macaddr,
             ":",
             tid->tid,
             tid->sched, tid->paused,
             tid->incomp, tid->baw_head,
             tid->baw_tail, tap == NULL ? -1 : tap->txa_start,
             ni->ni_txseqs[tid->tid]);

        /* XXX Dump the frame, see what it is? */
        ieee80211_dump_pkt(ni->ni_ic,
            mtod(bf->bf_m, const uint8_t *),
            bf->bf_m->m_len, 0, -1);
}

/*
 * Free any packets currently pending in the software TX queue.
 *
 * This will be called when a node is being deleted.
 *
 * It can also be called on an active node during an interface
 * reset or state transition.
 *
 * (From Linux/reference):
 *
 * TODO: For frame(s) that are in the retry state, we will reuse the
 * sequence number(s) without setting the retry bit. The
 * alternative is to give up on these and BAR the receiver's window
 * forward.
 */
static void
ath_tx_tid_drain(struct ath_softc *sc, struct ath_node *an,
    struct ath_tid *tid, ath_bufhead *bf_cq)
{
        struct ath_buf *bf;
        struct ieee80211_tx_ampdu *tap;
        struct ieee80211_node *ni = &an->an_node;
        int t;

        tap = ath_tx_get_tx_tid(an, tid->tid);

        ATH_TX_LOCK_ASSERT(sc);

        /* Walk the queue, free frames */
        t = 0;
        for (;;) {
                bf = ATH_TID_FIRST(tid);
                if (bf == NULL) {
                        break;
                }

                if (t == 0) {
                        ath_tx_tid_drain_print(sc, an, "norm", tid, bf);
                        t = 1;
                }

                ATH_TID_REMOVE(tid, bf, bf_list);
                ath_tx_tid_drain_pkt(sc, an, tid, bf_cq, bf);
        }

        /* And now, drain the filtered frame queue */
        t = 0;
        for (;;) {
                bf = ATH_TID_FILT_FIRST(tid);
                if (bf == NULL)
                        break;

                if (t == 0) {
                        ath_tx_tid_drain_print(sc, an, "filt", tid, bf);
                        t = 1;
                }

                ATH_TID_FILT_REMOVE(tid, bf, bf_list);
                ath_tx_tid_drain_pkt(sc, an, tid, bf_cq, bf);
        }

        /*
         * Override the clrdmask configuration for the next frame
         * in case there is some future transmission, just to get
         * the ball rolling.
         *
         * This won't hurt things if the TID is about to be freed.
         */
        ath_tx_set_clrdmask(sc, tid->an);

        /*
         * Now that it's completed, grab the TID lock and update
         * the sequence number and BAW window.
         * Because sequence numbers have been assigned to frames
         * that haven't been sent yet, it's entirely possible
         * we'll be called with some pending frames that have not
         * been transmitted.
         *
         * The cleaner solution is to do the sequence number allocation
         * when the packet is first transmitted - and thus the "retries"
         * check above would be enough to update the BAW/seqno.
         */

        /* But don't do it for non-QoS TIDs */
        if (tap) {
#if 1
                DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL,
                    "%s: %6D: node %p: TID %d: sliding BAW left edge to %d\n",
                    __func__,
                    ni->ni_macaddr,
                    ":",
                    an,
                    tid->tid,
                    tap->txa_start);
#endif
                ni->ni_txseqs[tid->tid] = tap->txa_start;
                tid->baw_tail = tid->baw_head;
        }
}

/*
 * Reset the TID state.  This must be only called once the node has
 * had its frames flushed from this TID, to ensure that no other
 * pause / unpause logic can kick in.
 */
static void
ath_tx_tid_reset(struct ath_softc *sc, struct ath_tid *tid)
{

#if 0
        tid->bar_wait = tid->bar_tx = tid->isfiltered = 0;
        tid->paused = tid->sched = tid->addba_tx_pending = 0;
        tid->incomp = tid->cleanup_inprogress = 0;
#endif

        /*
         * If we have a bar_wait set, we need to unpause the TID
         * here.  Otherwise once cleanup has finished, the TID won't
         * have the right paused counter.
         *
         * XXX I'm not going through resume here - I don't want the
         * node to be rescheuled just yet.  This however should be
         * methodized!
         */
        if (tid->bar_wait) {
                if (tid->paused > 0) {
                        tid->paused --;
                }
        }

        /*
         * XXX same with a currently filtered TID.
         *
         * Since this is being called during a flush, we assume that
         * the filtered frame list is actually empty.
         *
         * XXX TODO: add in a check to ensure that the filtered queue
         * depth is actually 0!
         */
        if (tid->isfiltered) {
                if (tid->paused > 0) {
                        tid->paused --;
                }
        }

        /*
         * Clear BAR, filtered frames, scheduled and ADDBA pending.
         * The TID may be going through cleanup from the last association
         * where things in the BAW are still in the hardware queue.
         */
        tid->bar_wait = 0;
        tid->bar_tx = 0;
        tid->isfiltered = 0;
        tid->sched = 0;
        tid->addba_tx_pending = 0;

        /*
         * XXX TODO: it may just be enough to walk the HWQs and mark
         * frames for that node as non-aggregate; or mark the ath_node
         * with something that indicates that aggregation is no longer
         * occuring.  Then we can just toss the BAW complaints and
         * do a complete hard reset of state here - no pause, no
         * complete counter, etc.
         */

}

/*
 * Flush all software queued packets for the given node.
 *
 * This occurs when a completion handler frees the last buffer
 * for a node, and the node is thus freed. This causes the node
 * to be cleaned up, which ends up calling ath_tx_node_flush.
 */
void
ath_tx_node_flush(struct ath_softc *sc, struct ath_node *an)
{
        int tid;
        ath_bufhead bf_cq;
        struct ath_buf *bf;

        TAILQ_INIT(&bf_cq);

        ATH_KTR(sc, ATH_KTR_NODE, 1, "ath_tx_node_flush: flush node; ni=%p",
            &an->an_node);

        ATH_TX_LOCK(sc);
        DPRINTF(sc, ATH_DEBUG_NODE,
            "%s: %6D: flush; is_powersave=%d, stack_psq=%d, tim=%d, "
            "swq_depth=%d, clrdmask=%d, leak_count=%d\n",
            __func__,
            an->an_node.ni_macaddr,
            ":",
            an->an_is_powersave,
            an->an_stack_psq,
            an->an_tim_set,
            an->an_swq_depth,
            an->clrdmask,
            an->an_leak_count);

        for (tid = 0; tid < IEEE80211_TID_SIZE; tid++) {
                struct ath_tid *atid = &an->an_tid[tid];

                /* Free packets */
                ath_tx_tid_drain(sc, an, atid, &bf_cq);

                /* Remove this tid from the list of active tids */
                ath_tx_tid_unsched(sc, atid);

                /* Reset the per-TID pause, BAR, etc state */
                ath_tx_tid_reset(sc, atid);
        }

        /*
         * Clear global leak count
         */
        an->an_leak_count = 0;
        ATH_TX_UNLOCK(sc);

        /* Handle completed frames */
        while ((bf = TAILQ_FIRST(&bf_cq)) != NULL) {
                TAILQ_REMOVE(&bf_cq, bf, bf_list);
                ath_tx_default_comp(sc, bf, 0);
        }
}

/*
 * Drain all the software TXQs currently with traffic queued.
 */
void
ath_tx_txq_drain(struct ath_softc *sc, struct ath_txq *txq)
{
        struct ath_tid *tid;
        ath_bufhead bf_cq;
        struct ath_buf *bf;

        TAILQ_INIT(&bf_cq);
        ATH_TX_LOCK(sc);

        /*
         * Iterate over all active tids for the given txq,
         * flushing and unsched'ing them
         */
        while (! TAILQ_EMPTY(&txq->axq_tidq)) {
                tid = TAILQ_FIRST(&txq->axq_tidq);
                ath_tx_tid_drain(sc, tid->an, tid, &bf_cq);
                ath_tx_tid_unsched(sc, tid);
        }

        ATH_TX_UNLOCK(sc);

        while ((bf = TAILQ_FIRST(&bf_cq)) != NULL) {
                TAILQ_REMOVE(&bf_cq, bf, bf_list);
                ath_tx_default_comp(sc, bf, 0);
        }
}

/*
 * Handle completion of non-aggregate session frames.
 *
 * This (currently) doesn't implement software retransmission of
 * non-aggregate frames!
 *
 * Software retransmission of non-aggregate frames needs to obey
 * the strict sequence number ordering, and drop any frames that
 * will fail this.
 *
 * For now, filtered frames and frame transmission will cause
 * all kinds of issues.  So we don't support them.
 *
 * So anyone queuing frames via ath_tx_normal_xmit() or
 * ath_tx_hw_queue_norm() must override and set CLRDMASK.
 */
void
ath_tx_normal_comp(struct ath_softc *sc, struct ath_buf *bf, int fail)
{
        struct ieee80211_node *ni = bf->bf_node;
        struct ath_node *an = ATH_NODE(ni);
        int tid = bf->bf_state.bfs_tid;
        struct ath_tid *atid = &an->an_tid[tid];
        struct ath_tx_status *ts = &bf->bf_status.ds_txstat;

        /* The TID state is protected behind the TXQ lock */
        ATH_TX_LOCK(sc);

        DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: bf=%p: fail=%d, hwq_depth now %d\n",
            __func__, bf, fail, atid->hwq_depth - 1);

        atid->hwq_depth--;

#if 0
        /*
         * If the frame was filtered, stick it on the filter frame
         * queue and complain about it.  It shouldn't happen!
         */
        if ((ts->ts_status & HAL_TXERR_FILT) ||
            (ts->ts_status != 0 && atid->isfiltered)) {
                DPRINTF(sc, ATH_DEBUG_SW_TX,
                    "%s: isfiltered=%d, ts_status=%d: huh?\n",
                    __func__,
                    atid->isfiltered,
                    ts->ts_status);
                ath_tx_tid_filt_comp_buf(sc, atid, bf);
        }
#endif
        if (atid->isfiltered)
                DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: filtered?!\n", __func__);
        if (atid->hwq_depth < 0)
                DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: hwq_depth < 0: %d\n",
                    __func__, atid->hwq_depth);

        /*
         * If the queue is filtered, potentially mark it as complete
         * and reschedule it as needed.
         *
         * This is required as there may be a subsequent TX descriptor
         * for this end-node that has CLRDMASK set, so it's quite possible
         * that a filtered frame will be followed by a non-filtered
         * (complete or otherwise) frame.
         *
         * XXX should we do this before we complete the frame?
         */
        if (atid->isfiltered)
                ath_tx_tid_filt_comp_complete(sc, atid);
        ATH_TX_UNLOCK(sc);

        /*
         * punt to rate control if we're not being cleaned up
         * during a hw queue drain and the frame wanted an ACK.
         */
        if (fail == 0 && ((bf->bf_state.bfs_txflags & HAL_TXDESC_NOACK) == 0))
                ath_tx_update_ratectrl(sc, ni, bf->bf_state.bfs_rc,
                    ts, bf->bf_state.bfs_pktlen,
                    1, (ts->ts_status == 0) ? 0 : 1);

        ath_tx_default_comp(sc, bf, fail);
}

/*
 * Handle cleanup of aggregate session packets that aren't
 * an A-MPDU.
 *
 * There's no need to update the BAW here - the session is being
 * torn down.
 */
static void
ath_tx_comp_cleanup_unaggr(struct ath_softc *sc, struct ath_buf *bf)
{
        struct ieee80211_node *ni = bf->bf_node;
        struct ath_node *an = ATH_NODE(ni);
        int tid = bf->bf_state.bfs_tid;
        struct ath_tid *atid = &an->an_tid[tid];

        DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL, "%s: TID %d: incomp=%d\n",
            __func__, tid, atid->incomp);

        ATH_TX_LOCK(sc);
        atid->incomp--;
        if (atid->incomp == 0) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL,
                    "%s: TID %d: cleaned up! resume!\n",
                    __func__, tid);
                atid->cleanup_inprogress = 0;
                ath_tx_tid_resume(sc, atid);
        }
        ATH_TX_UNLOCK(sc);

        ath_tx_default_comp(sc, bf, 0);
}

/*
 * Performs transmit side cleanup when TID changes from aggregated to
 * unaggregated.
 *
 * - Discard all retry frames from the s/w queue.
 * - Fix the tx completion function for all buffers in s/w queue.
 * - Count the number of unacked frames, and let transmit completion
 *   handle it later.
 *
 * The caller is responsible for pausing the TID and unpausing the
 * TID if no cleanup was required. Otherwise the cleanup path will
 * unpause the TID once the last hardware queued frame is completed.
 */
static void
ath_tx_tid_cleanup(struct ath_softc *sc, struct ath_node *an, int tid,
    ath_bufhead *bf_cq)
{
        struct ath_tid *atid = &an->an_tid[tid];
        struct ieee80211_tx_ampdu *tap;
        struct ath_buf *bf, *bf_next;

        ATH_TX_LOCK_ASSERT(sc);

        DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
            "%s: TID %d: called\n", __func__, tid);

        /*
         * Move the filtered frames to the TX queue, before
         * we run off and discard/process things.
         */
        /* XXX this is really quite inefficient */
        while ((bf = ATH_TID_FILT_LAST(atid, ath_bufhead_s)) != NULL) {
                ATH_TID_FILT_REMOVE(atid, bf, bf_list);
                ATH_TID_INSERT_HEAD(atid, bf, bf_list);
        }

        /*
         * Update the frames in the software TX queue:
         *
         * + Discard retry frames in the queue
         * + Fix the completion function to be non-aggregate
         */
        bf = ATH_TID_FIRST(atid);
        while (bf) {
                if (bf->bf_state.bfs_isretried) {
                        bf_next = TAILQ_NEXT(bf, bf_list);
                        ATH_TID_REMOVE(atid, bf, bf_list);
                        if (bf->bf_state.bfs_dobaw) {
                                ath_tx_update_baw(sc, an, atid, bf);
                                if (!bf->bf_state.bfs_addedbaw)
                                        DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
                                            "%s: wasn't added: seqno %d\n",
                                            __func__,
                                            SEQNO(bf->bf_state.bfs_seqno));
                        }
                        bf->bf_state.bfs_dobaw = 0;
                        /*
                         * Call the default completion handler with "fail" just
                         * so upper levels are suitably notified about this.
                         */
                        TAILQ_INSERT_TAIL(bf_cq, bf, bf_list);
                        bf = bf_next;
                        continue;
                }
                /* Give these the default completion handler */
                bf->bf_comp = ath_tx_normal_comp;
                bf = TAILQ_NEXT(bf, bf_list);
        }

        /*
         * Calculate what hardware-queued frames exist based
         * on the current BAW size. Ie, what frames have been
         * added to the TX hardware queue for this TID but
         * not yet ACKed.
         */
        tap = ath_tx_get_tx_tid(an, tid);
        /* Need the lock - fiddling with BAW */
        while (atid->baw_head != atid->baw_tail) {
                if (atid->tx_buf[atid->baw_head]) {
                        atid->incomp++;
                        atid->cleanup_inprogress = 1;
                        atid->tx_buf[atid->baw_head] = NULL;
                }
                INCR(atid->baw_head, ATH_TID_MAX_BUFS);
                INCR(tap->txa_start, IEEE80211_SEQ_RANGE);
        }

        if (atid->cleanup_inprogress)
                DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL,
                    "%s: TID %d: cleanup needed: %d packets\n",
                    __func__, tid, atid->incomp);

        /* Owner now must free completed frames */
}

static struct ath_buf *
ath_tx_retry_clone(struct ath_softc *sc, struct ath_node *an,
    struct ath_tid *tid, struct ath_buf *bf)
{
        struct ath_buf *nbf;
        int error;

        /*
         * Clone the buffer.  This will handle the dma unmap and
         * copy the node reference to the new buffer.  If this
         * works out, 'bf' will have no DMA mapping, no mbuf
         * pointer and no node reference.
         */
        nbf = ath_buf_clone(sc, bf);

#if 0
        DPRINTF(sc, ATH_DEBUG_XMIT, "%s: ATH_BUF_BUSY; cloning\n",
            __func__);
#endif

        if (nbf == NULL) {
                /* Failed to clone */
                DPRINTF(sc, ATH_DEBUG_XMIT,
                    "%s: failed to clone a busy buffer\n",
                    __func__);
                return NULL;
        }

        /* Setup the dma for the new buffer */
        error = ath_tx_dmasetup(sc, nbf, nbf->bf_m);
        if (error != 0) {
                DPRINTF(sc, ATH_DEBUG_XMIT,
                    "%s: failed to setup dma for clone\n",
                    __func__);
                /*
                 * Put this at the head of the list, not tail;
                 * that way it doesn't interfere with the
                 * busy buffer logic (which uses the tail of
                 * the list.)
                 */
                ATH_TXBUF_LOCK(sc);
                ath_returnbuf_head(sc, nbf);
                ATH_TXBUF_UNLOCK(sc);
                return NULL;
        }

        /* Update BAW if required, before we free the original buf */
        if (bf->bf_state.bfs_dobaw)
                ath_tx_switch_baw_buf(sc, an, tid, bf, nbf);

        /* Free original buffer; return new buffer */
        ath_freebuf(sc, bf);

        return nbf;
}

/*
 * Handle retrying an unaggregate frame in an aggregate
 * session.
 *
 * If too many retries occur, pause the TID, wait for
 * any further retransmits (as there's no reason why
 * non-aggregate frames in an aggregate session are
 * transmitted in-order; they just have to be in-BAW)
 * and then queue a BAR.
 */
static void
ath_tx_aggr_retry_unaggr(struct ath_softc *sc, struct ath_buf *bf)
{
        struct ieee80211_node *ni = bf->bf_node;
        struct ath_node *an = ATH_NODE(ni);
        int tid = bf->bf_state.bfs_tid;
        struct ath_tid *atid = &an->an_tid[tid];
        struct ieee80211_tx_ampdu *tap;

        ATH_TX_LOCK(sc);

        tap = ath_tx_get_tx_tid(an, tid);

        /*
         * If the buffer is marked as busy, we can't directly
         * reuse it. Instead, try to clone the buffer.
         * If the clone is successful, recycle the old buffer.
         * If the clone is unsuccessful, set bfs_retries to max
         * to force the next bit of code to free the buffer
         * for us.
         */
        if ((bf->bf_state.bfs_retries < SWMAX_RETRIES) &&
            (bf->bf_flags & ATH_BUF_BUSY)) {
                struct ath_buf *nbf;
                nbf = ath_tx_retry_clone(sc, an, atid, bf);
                if (nbf)
                        /* bf has been freed at this point */
                        bf = nbf;
                else
                        bf->bf_state.bfs_retries = SWMAX_RETRIES + 1;
        }

        if (bf->bf_state.bfs_retries >= SWMAX_RETRIES) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_RETRIES,
                    "%s: exceeded retries; seqno %d\n",
                    __func__, SEQNO(bf->bf_state.bfs_seqno));
                sc->sc_stats.ast_tx_swretrymax++;

                /* Update BAW anyway */
                if (bf->bf_state.bfs_dobaw) {
                        ath_tx_update_baw(sc, an, atid, bf);
                        if (! bf->bf_state.bfs_addedbaw)
                                DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
                                    "%s: wasn't added: seqno %d\n",
                                    __func__, SEQNO(bf->bf_state.bfs_seqno));
                }
                bf->bf_state.bfs_dobaw = 0;

                /* Suspend the TX queue and get ready to send the BAR */
                ath_tx_tid_bar_suspend(sc, atid);

                /* Send the BAR if there are no other frames waiting */
                if (ath_tx_tid_bar_tx_ready(sc, atid))
                        ath_tx_tid_bar_tx(sc, atid);

                ATH_TX_UNLOCK(sc);

                /* Free buffer, bf is free after this call */
                ath_tx_default_comp(sc, bf, 0);
                return;
        }

        /*
         * This increments the retry counter as well as
         * sets the retry flag in the ath_buf and packet
         * body.
         */
        ath_tx_set_retry(sc, bf);
        sc->sc_stats.ast_tx_swretries++;

        /*
         * Insert this at the head of the queue, so it's
         * retried before any current/subsequent frames.
         */
        ATH_TID_INSERT_HEAD(atid, bf, bf_list);
        ath_tx_tid_sched(sc, atid);
        /* Send the BAR if there are no other frames waiting */
        if (ath_tx_tid_bar_tx_ready(sc, atid))
                ath_tx_tid_bar_tx(sc, atid);

        ATH_TX_UNLOCK(sc);
}

/*
 * Common code for aggregate excessive retry/subframe retry.
 * If retrying, queues buffers to bf_q. If not, frees the
 * buffers.
 *
 * XXX should unify this with ath_tx_aggr_retry_unaggr()
 */
static int
ath_tx_retry_subframe(struct ath_softc *sc, struct ath_buf *bf,
    ath_bufhead *bf_q)
{
        struct ieee80211_node *ni = bf->bf_node;
        struct ath_node *an = ATH_NODE(ni);
        int tid = bf->bf_state.bfs_tid;
        struct ath_tid *atid = &an->an_tid[tid];

        ATH_TX_LOCK_ASSERT(sc);

        /* XXX clr11naggr should be done for all subframes */
        ath_hal_clr11n_aggr(sc->sc_ah, bf->bf_desc);
        ath_hal_set11nburstduration(sc->sc_ah, bf->bf_desc, 0);

        /* ath_hal_set11n_virtualmorefrag(sc->sc_ah, bf->bf_desc, 0); */

        /*
         * If the buffer is marked as busy, we can't directly
         * reuse it. Instead, try to clone the buffer.
         * If the clone is successful, recycle the old buffer.
         * If the clone is unsuccessful, set bfs_retries to max
         * to force the next bit of code to free the buffer
         * for us.
         */
        if ((bf->bf_state.bfs_retries < SWMAX_RETRIES) &&
            (bf->bf_flags & ATH_BUF_BUSY)) {
                struct ath_buf *nbf;
                nbf = ath_tx_retry_clone(sc, an, atid, bf);
                if (nbf)
                        /* bf has been freed at this point */
                        bf = nbf;
                else
                        bf->bf_state.bfs_retries = SWMAX_RETRIES + 1;
        }

        if (bf->bf_state.bfs_retries >= SWMAX_RETRIES) {
                sc->sc_stats.ast_tx_swretrymax++;
                DPRINTF(sc, ATH_DEBUG_SW_TX_RETRIES,
                    "%s: max retries: seqno %d\n",
                    __func__, SEQNO(bf->bf_state.bfs_seqno));
                ath_tx_update_baw(sc, an, atid, bf);
                if (!bf->bf_state.bfs_addedbaw)
                        DPRINTF(sc, ATH_DEBUG_SW_TX_BAW,
                            "%s: wasn't added: seqno %d\n",
                            __func__, SEQNO(bf->bf_state.bfs_seqno));
                bf->bf_state.bfs_dobaw = 0;
                return 1;
        }

        ath_tx_set_retry(sc, bf);
        sc->sc_stats.ast_tx_swretries++;
        bf->bf_next = NULL;             /* Just to make sure */

        /* Clear the aggregate state */
        bf->bf_state.bfs_aggr = 0;
        bf->bf_state.bfs_ndelim = 0;    /* ??? needed? */
        bf->bf_state.bfs_nframes = 1;

        TAILQ_INSERT_TAIL(bf_q, bf, bf_list);
        return 0;
}

/*
 * error pkt completion for an aggregate destination
 */
static void
ath_tx_comp_aggr_error(struct ath_softc *sc, struct ath_buf *bf_first,
    struct ath_tid *tid)
{
        struct ieee80211_node *ni = bf_first->bf_node;
        struct ath_node *an = ATH_NODE(ni);
        struct ath_buf *bf_next, *bf;
        ath_bufhead bf_q;
        int drops = 0;
        struct ieee80211_tx_ampdu *tap;
        ath_bufhead bf_cq;

        TAILQ_INIT(&bf_q);
        TAILQ_INIT(&bf_cq);

        /*
         * Update rate control - all frames have failed.
         *
         * XXX use the length in the first frame in the series;
         * XXX just so things are consistent for now.
         */
        ath_tx_update_ratectrl(sc, ni, bf_first->bf_state.bfs_rc,
            &bf_first->bf_status.ds_txstat,
            bf_first->bf_state.bfs_pktlen,
            bf_first->bf_state.bfs_nframes, bf_first->bf_state.bfs_nframes);

        ATH_TX_LOCK(sc);
        tap = ath_tx_get_tx_tid(an, tid->tid);
        sc->sc_stats.ast_tx_aggr_failall++;

        /* Retry all subframes */
        bf = bf_first;
        while (bf) {
                bf_next = bf->bf_next;
                bf->bf_next = NULL;     /* Remove it from the aggr list */
                sc->sc_stats.ast_tx_aggr_fail++;
                if (ath_tx_retry_subframe(sc, bf, &bf_q)) {
                        drops++;
                        bf->bf_next = NULL;
                        TAILQ_INSERT_TAIL(&bf_cq, bf, bf_list);
                }
                bf = bf_next;
        }

        /* Prepend all frames to the beginning of the queue */
        while ((bf = TAILQ_LAST(&bf_q, ath_bufhead_s)) != NULL) {
                TAILQ_REMOVE(&bf_q, bf, bf_list);
                ATH_TID_INSERT_HEAD(tid, bf, bf_list);
        }

        /*
         * Schedule the TID to be re-tried.
         */
        ath_tx_tid_sched(sc, tid);

        /*
         * send bar if we dropped any frames
         *
         * Keep the txq lock held for now, as we need to ensure
         * that ni_txseqs[] is consistent (as it's being updated
         * in the ifnet TX context or raw TX context.)
         */
        if (drops) {
                /* Suspend the TX queue and get ready to send the BAR */
                ath_tx_tid_bar_suspend(sc, tid);
        }

        /*
         * Send BAR if required
         */
        if (ath_tx_tid_bar_tx_ready(sc, tid))
                ath_tx_tid_bar_tx(sc, tid);

        ATH_TX_UNLOCK(sc);

        /* Complete frames which errored out */
        while ((bf = TAILQ_FIRST(&bf_cq)) != NULL) {
                TAILQ_REMOVE(&bf_cq, bf, bf_list);
                ath_tx_default_comp(sc, bf, 0);
        }
}

/*
 * Handle clean-up of packets from an aggregate list.
 *
 * There's no need to update the BAW here - the session is being
 * torn down.
 */
static void
ath_tx_comp_cleanup_aggr(struct ath_softc *sc, struct ath_buf *bf_first)
{
        struct ath_buf *bf, *bf_next;
        struct ieee80211_node *ni = bf_first->bf_node;
        struct ath_node *an = ATH_NODE(ni);
        int tid = bf_first->bf_state.bfs_tid;
        struct ath_tid *atid = &an->an_tid[tid];

        ATH_TX_LOCK(sc);

        /* update incomp */
        bf = bf_first;
        while (bf) {
                atid->incomp--;
                bf = bf->bf_next;
        }

        if (atid->incomp == 0) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL,
                    "%s: TID %d: cleaned up! resume!\n",
                    __func__, tid);
                atid->cleanup_inprogress = 0;
                ath_tx_tid_resume(sc, atid);
        }

        /* Send BAR if required */
        /* XXX why would we send a BAR when transitioning to non-aggregation? */
        /*
         * XXX TODO: we should likely just tear down the BAR state here,
         * rather than sending a BAR.
         */
        if (ath_tx_tid_bar_tx_ready(sc, atid))
                ath_tx_tid_bar_tx(sc, atid);

        ATH_TX_UNLOCK(sc);

        /* Handle frame completion */
        bf = bf_first;
        while (bf) {
                bf_next = bf->bf_next;
                ath_tx_default_comp(sc, bf, 1);
                bf = bf_next;
        }
}

/*
 * Handle completion of an set of aggregate frames.
 *
 * Note: the completion handler is the last descriptor in the aggregate,
 * not the last descriptor in the first frame.
 */
static void
ath_tx_aggr_comp_aggr(struct ath_softc *sc, struct ath_buf *bf_first,
    int fail)
{
        //struct ath_desc *ds = bf->bf_lastds;
        struct ieee80211_node *ni = bf_first->bf_node;
        struct ath_node *an = ATH_NODE(ni);
        int tid = bf_first->bf_state.bfs_tid;
        struct ath_tid *atid = &an->an_tid[tid];
        struct ath_tx_status ts;
        struct ieee80211_tx_ampdu *tap;
        ath_bufhead bf_q;
        ath_bufhead bf_cq;
        int seq_st, tx_ok;
        int hasba, isaggr;
        uint32_t ba[2];
        struct ath_buf *bf, *bf_next;
        int ba_index;
        int drops = 0;
        int nframes = 0, nbad = 0, nf;
        int pktlen;
        /* XXX there's too much on the stack? */
        struct ath_rc_series rc[ATH_RC_NUM];
        int txseq;

        DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR, "%s: called; hwq_depth=%d\n",
            __func__, atid->hwq_depth);

        /*
         * Take a copy; this may be needed -after- bf_first
         * has been completed and freed.
         */
        ts = bf_first->bf_status.ds_txstat;

        TAILQ_INIT(&bf_q);
        TAILQ_INIT(&bf_cq);

        /* The TID state is kept behind the TXQ lock */
        ATH_TX_LOCK(sc);

        atid->hwq_depth--;
        if (atid->hwq_depth < 0)
                DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR, "%s: hwq_depth < 0: %d\n",
                    __func__, atid->hwq_depth);

        /*
         * If the TID is filtered, handle completing the filter
         * transition before potentially kicking it to the cleanup
         * function.
         *
         * XXX this is duplicate work, ew.
         */
        if (atid->isfiltered)
                ath_tx_tid_filt_comp_complete(sc, atid);

        /*
         * Punt cleanup to the relevant function, not our problem now
         */
        if (atid->cleanup_inprogress) {
                if (atid->isfiltered)
                        DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
                            "%s: isfiltered=1, normal_comp?\n",
                            __func__);
                ATH_TX_UNLOCK(sc);
                ath_tx_comp_cleanup_aggr(sc, bf_first);
                return;
        }

        /*
         * If the frame is filtered, transition to filtered frame
         * mode and add this to the filtered frame list.
         *
         * XXX TODO: figure out how this interoperates with
         * BAR, pause and cleanup states.
         */
        if ((ts.ts_status & HAL_TXERR_FILT) ||
            (ts.ts_status != 0 && atid->isfiltered)) {
                if (fail != 0)
                        DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
                            "%s: isfiltered=1, fail=%d\n", __func__, fail);
                ath_tx_tid_filt_comp_aggr(sc, atid, bf_first, &bf_cq);

                /* Remove from BAW */
                TAILQ_FOREACH_SAFE(bf, &bf_cq, bf_list, bf_next) {
                        if (bf->bf_state.bfs_addedbaw)
                                drops++;
                        if (bf->bf_state.bfs_dobaw) {
                                ath_tx_update_baw(sc, an, atid, bf);
                                if (!bf->bf_state.bfs_addedbaw)
                                        DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
                                            "%s: wasn't added: seqno %d\n",
                                            __func__,
                                            SEQNO(bf->bf_state.bfs_seqno));
                        }
                        bf->bf_state.bfs_dobaw = 0;
                }
                /*
                 * If any intermediate frames in the BAW were dropped when
                 * handling filtering things, send a BAR.
                 */
                if (drops)
                        ath_tx_tid_bar_suspend(sc, atid);

                /*
                 * Finish up by sending a BAR if required and freeing
                 * the frames outside of the TX lock.
                 */
                goto finish_send_bar;
        }

        /*
         * XXX for now, use the first frame in the aggregate for
         * XXX rate control completion; it's at least consistent.
         */
        pktlen = bf_first->bf_state.bfs_pktlen;

        /*
         * Handle errors first!
         *
         * Here, handle _any_ error as a "exceeded retries" error.
         * Later on (when filtered frames are to be specially handled)
         * it'll have to be expanded.
         */
#if 0
        if (ts.ts_status & HAL_TXERR_XRETRY) {
#endif
        if (ts.ts_status != 0) {
                ATH_TX_UNLOCK(sc);
                ath_tx_comp_aggr_error(sc, bf_first, atid);
                return;
        }

        tap = ath_tx_get_tx_tid(an, tid);

        /*
         * extract starting sequence and block-ack bitmap
         */
        /* XXX endian-ness of seq_st, ba? */
        seq_st = ts.ts_seqnum;
        hasba = !! (ts.ts_flags & HAL_TX_BA);
        tx_ok = (ts.ts_status == 0);
        isaggr = bf_first->bf_state.bfs_aggr;
        ba[0] = ts.ts_ba_low;
        ba[1] = ts.ts_ba_high;

        /*
         * Copy the TX completion status and the rate control
         * series from the first descriptor, as it may be freed
         * before the rate control code can get its grubby fingers
         * into things.
         */
        memcpy(rc, bf_first->bf_state.bfs_rc, sizeof(rc));

        DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
            "%s: txa_start=%d, tx_ok=%d, status=%.8x, flags=%.8x, "
            "isaggr=%d, seq_st=%d, hasba=%d, ba=%.8x, %.8x\n",
            __func__, tap->txa_start, tx_ok, ts.ts_status, ts.ts_flags,
            isaggr, seq_st, hasba, ba[0], ba[1]);

        /*
         * The reference driver doesn't do this; it simply ignores
         * this check in its entirety.
         *
         * I've seen this occur when using iperf to send traffic
         * out tid 1 - the aggregate frames are all marked as TID 1,
         * but the TXSTATUS has TID=0.  So, let's just ignore this
         * check.
         */
#if 0
        /* Occasionally, the MAC sends a tx status for the wrong TID. */
        if (tid != ts.ts_tid) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR, "%s: tid %d != hw tid %d\n",
                    __func__, tid, ts.ts_tid);
                tx_ok = 0;
        }
#endif

        /* AR5416 BA bug; this requires an interface reset */
        if (isaggr && tx_ok && (! hasba)) {
                DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
                    "%s: AR5416 bug: hasba=%d; txok=%d, isaggr=%d, "
                    "seq_st=%d\n",
                    __func__, hasba, tx_ok, isaggr, seq_st);
                /* XXX TODO: schedule an interface reset */
#ifdef ATH_DEBUG
                ath_printtxbuf(sc, bf_first,
                    sc->sc_ac2q[atid->ac]->axq_qnum, 0, 0);
#endif
        }

        /*
         * Walk the list of frames, figure out which ones were correctly
         * sent and which weren't.
         */
        bf = bf_first;
        nf = bf_first->bf_state.bfs_nframes;

        /* bf_first is going to be invalid once this list is walked */
        bf_first = NULL;

        /*
         * Walk the list of completed frames and determine
         * which need to be completed and which need to be
         * retransmitted.
         *
         * For completed frames, the completion functions need
         * to be called at the end of this function as the last
         * node reference may free the node.
         *
         * Finally, since the TXQ lock can't be held during the
         * completion callback (to avoid lock recursion),
         * the completion calls have to be done outside of the
         * lock.
         */
        while (bf) {
                nframes++;
                ba_index = ATH_BA_INDEX(seq_st,
                    SEQNO(bf->bf_state.bfs_seqno));
                bf_next = bf->bf_next;
                bf->bf_next = NULL;     /* Remove it from the aggr list */

                DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
                    "%s: checking bf=%p seqno=%d; ack=%d\n",
                    __func__, bf, SEQNO(bf->bf_state.bfs_seqno),
                    ATH_BA_ISSET(ba, ba_index));

                if (tx_ok && ATH_BA_ISSET(ba, ba_index)) {
                        sc->sc_stats.ast_tx_aggr_ok++;
                        ath_tx_update_baw(sc, an, atid, bf);
                        bf->bf_state.bfs_dobaw = 0;
                        if (!bf->bf_state.bfs_addedbaw)
                                DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
                                    "%s: wasn't added: seqno %d\n",
                                    __func__, SEQNO(bf->bf_state.bfs_seqno));
                        bf->bf_next = NULL;
                        TAILQ_INSERT_TAIL(&bf_cq, bf, bf_list);
                } else {
                        sc->sc_stats.ast_tx_aggr_fail++;
                        if (ath_tx_retry_subframe(sc, bf, &bf_q)) {
                                drops++;
                                bf->bf_next = NULL;
                                TAILQ_INSERT_TAIL(&bf_cq, bf, bf_list);
                        }
                        nbad++;
                }
                bf = bf_next;
        }

        /*
         * Now that the BAW updates have been done, unlock
         *
         * txseq is grabbed before the lock is released so we
         * have a consistent view of what -was- in the BAW.
         * Anything after this point will not yet have been
         * TXed.
         */
        txseq = tap->txa_start;
        ATH_TX_UNLOCK(sc);

        if (nframes != nf)
                DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
                    "%s: num frames seen=%d; bf nframes=%d\n",
                    __func__, nframes, nf);

        /*
         * Now we know how many frames were bad, call the rate
         * control code.
         */
        if (fail == 0)
                ath_tx_update_ratectrl(sc, ni, rc, &ts, pktlen, nframes,
                    nbad);

        /*
         * send bar if we dropped any frames
         */
        if (drops) {
                /* Suspend the TX queue and get ready to send the BAR */
                ATH_TX_LOCK(sc);
                ath_tx_tid_bar_suspend(sc, atid);
                ATH_TX_UNLOCK(sc);
        }

        DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
            "%s: txa_start now %d\n", __func__, tap->txa_start);

        ATH_TX_LOCK(sc);

        /* Prepend all frames to the beginning of the queue */
        while ((bf = TAILQ_LAST(&bf_q, ath_bufhead_s)) != NULL) {
                TAILQ_REMOVE(&bf_q, bf, bf_list);
                ATH_TID_INSERT_HEAD(atid, bf, bf_list);
        }

        /*
         * Reschedule to grab some further frames.
         */
        ath_tx_tid_sched(sc, atid);

        /*
         * If the queue is filtered, re-schedule as required.
         *
         * This is required as there may be a subsequent TX descriptor
         * for this end-node that has CLRDMASK set, so it's quite possible
         * that a filtered frame will be followed by a non-filtered
         * (complete or otherwise) frame.
         *
         * XXX should we do this before we complete the frame?
         */
        if (atid->isfiltered)
                ath_tx_tid_filt_comp_complete(sc, atid);

finish_send_bar:

        /*
         * Send BAR if required
         */
        if (ath_tx_tid_bar_tx_ready(sc, atid))
                ath_tx_tid_bar_tx(sc, atid);

        ATH_TX_UNLOCK(sc);

        /* Do deferred completion */
        while ((bf = TAILQ_FIRST(&bf_cq)) != NULL) {
                TAILQ_REMOVE(&bf_cq, bf, bf_list);
                ath_tx_default_comp(sc, bf, 0);
        }
}

/*
 * Handle completion of unaggregated frames in an ADDBA
 * session.
 *
 * Fail is set to 1 if the entry is being freed via a call to
 * ath_tx_draintxq().
 */
static void
ath_tx_aggr_comp_unaggr(struct ath_softc *sc, struct ath_buf *bf, int fail)
{
        struct ieee80211_node *ni = bf->bf_node;
        struct ath_node *an = ATH_NODE(ni);
        int tid = bf->bf_state.bfs_tid;
        struct ath_tid *atid = &an->an_tid[tid];
        struct ath_tx_status ts;
        int drops = 0;

        /*
         * Take a copy of this; filtering/cloning the frame may free the
         * bf pointer.
         */
        ts = bf->bf_status.ds_txstat;

        /*
         * Update rate control status here, before we possibly
         * punt to retry or cleanup.
         *
         * Do it outside of the TXQ lock.
         */
        if (fail == 0 && ((bf->bf_state.bfs_txflags & HAL_TXDESC_NOACK) == 0))
                ath_tx_update_ratectrl(sc, ni, bf->bf_state.bfs_rc,
                    &bf->bf_status.ds_txstat,
                    bf->bf_state.bfs_pktlen,
                    1, (ts.ts_status == 0) ? 0 : 1);

        /*
         * This is called early so atid->hwq_depth can be tracked.
         * This unfortunately means that it's released and regrabbed
         * during retry and cleanup. That's rather inefficient.
         */
        ATH_TX_LOCK(sc);

        if (tid == IEEE80211_NONQOS_TID)
                DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: TID=16!\n", __func__);

        DPRINTF(sc, ATH_DEBUG_SW_TX,
            "%s: bf=%p: tid=%d, hwq_depth=%d, seqno=%d\n",
            __func__, bf, bf->bf_state.bfs_tid, atid->hwq_depth,
            SEQNO(bf->bf_state.bfs_seqno));

        atid->hwq_depth--;
        if (atid->hwq_depth < 0)
                DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: hwq_depth < 0: %d\n",
                    __func__, atid->hwq_depth);

        /*
         * If the TID is filtered, handle completing the filter
         * transition before potentially kicking it to the cleanup
         * function.
         */
        if (atid->isfiltered)
                ath_tx_tid_filt_comp_complete(sc, atid);

        /*
         * If a cleanup is in progress, punt to comp_cleanup;
         * rather than handling it here. It's thus their
         * responsibility to clean up, call the completion
         * function in net80211, etc.
         */
        if (atid->cleanup_inprogress) {
                if (atid->isfiltered)
                        DPRINTF(sc, ATH_DEBUG_SW_TX,
                            "%s: isfiltered=1, normal_comp?\n",
                            __func__);
                ATH_TX_UNLOCK(sc);
                DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: cleanup_unaggr\n",
                    __func__);
                ath_tx_comp_cleanup_unaggr(sc, bf);
                return;
        }

        /*
         * XXX TODO: how does cleanup, BAR and filtered frame handling
         * overlap?
         *
         * If the frame is filtered OR if it's any failure but
         * the TID is filtered, the frame must be added to the
         * filtered frame list.
         *
         * However - a busy buffer can't be added to the filtered
         * list as it will end up being recycled without having
         * been made available for the hardware.
         */
        if ((ts.ts_status & HAL_TXERR_FILT) ||
            (ts.ts_status != 0 && atid->isfiltered)) {
                int freeframe;

                if (fail != 0)
                        DPRINTF(sc, ATH_DEBUG_SW_TX,
                            "%s: isfiltered=1, fail=%d\n",
                            __func__, fail);
                freeframe = ath_tx_tid_filt_comp_single(sc, atid, bf);
                if (freeframe) {
                        /* Remove from BAW */
                        if (bf->bf_state.bfs_addedbaw)
                                drops++;
                        if (bf->bf_state.bfs_dobaw) {
                                ath_tx_update_baw(sc, an, atid, bf);
                                if (!bf->bf_state.bfs_addedbaw)
                                        DPRINTF(sc, ATH_DEBUG_SW_TX,
                                            "%s: wasn't added: seqno %d\n",
                                            __func__, SEQNO(bf->bf_state.bfs_seqno));
                        }
                        bf->bf_state.bfs_dobaw = 0;
                }

                /*
                 * If the frame couldn't be filtered, treat it as a drop and
                 * prepare to send a BAR.
                 */
                if (freeframe && drops)
                        ath_tx_tid_bar_suspend(sc, atid);

                /*
                 * Send BAR if required
                 */
                if (ath_tx_tid_bar_tx_ready(sc, atid))
                        ath_tx_tid_bar_tx(sc, atid);

                ATH_TX_UNLOCK(sc);
                /*
                 * If freeframe is set, then the frame couldn't be
                 * cloned and bf is still valid.  Just complete/free it.
                 */
                if (freeframe)
                        ath_tx_default_comp(sc, bf, fail);


                return;
        }
        /*
         * Don't bother with the retry check if all frames
         * are being failed (eg during queue deletion.)
         */
#if 0
        if (fail == 0 && ts->ts_status & HAL_TXERR_XRETRY) {
#endif
        if (fail == 0 && ts.ts_status != 0) {
                ATH_TX_UNLOCK(sc);
                DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: retry_unaggr\n",
                    __func__);
                ath_tx_aggr_retry_unaggr(sc, bf);
                return;
        }

        /* Success? Complete */
        DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: TID=%d, seqno %d\n",
            __func__, tid, SEQNO(bf->bf_state.bfs_seqno));
        if (bf->bf_state.bfs_dobaw) {
                ath_tx_update_baw(sc, an, atid, bf);
                bf->bf_state.bfs_dobaw = 0;
                if (!bf->bf_state.bfs_addedbaw)
                        DPRINTF(sc, ATH_DEBUG_SW_TX,
                            "%s: wasn't added: seqno %d\n",
                            __func__, SEQNO(bf->bf_state.bfs_seqno));
        }

        /*
         * If the queue is filtered, re-schedule as required.
         *
         * This is required as there may be a subsequent TX descriptor
         * for this end-node that has CLRDMASK set, so it's quite possible
         * that a filtered frame will be followed by a non-filtered
         * (complete or otherwise) frame.
         *
         * XXX should we do this before we complete the frame?
         */
        if (atid->isfiltered)
                ath_tx_tid_filt_comp_complete(sc, atid);

        /*
         * Send BAR if required
         */
        if (ath_tx_tid_bar_tx_ready(sc, atid))
                ath_tx_tid_bar_tx(sc, atid);

        ATH_TX_UNLOCK(sc);

        ath_tx_default_comp(sc, bf, fail);
        /* bf is freed at this point */
}

void
ath_tx_aggr_comp(struct ath_softc *sc, struct ath_buf *bf, int fail)
{
        if (bf->bf_state.bfs_aggr)
                ath_tx_aggr_comp_aggr(sc, bf, fail);
        else
                ath_tx_aggr_comp_unaggr(sc, bf, fail);
}

/*
 * Schedule some packets from the given node/TID to the hardware.
 *
 * This is the aggregate version.
 */
void
ath_tx_tid_hw_queue_aggr(struct ath_softc *sc, struct ath_node *an,
    struct ath_tid *tid)
{
        struct ath_buf *bf;
        struct ath_txq *txq = sc->sc_ac2q[tid->ac];
        struct ieee80211_tx_ampdu *tap;
        ATH_AGGR_STATUS status;
        ath_bufhead bf_q;

        DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: tid=%d\n", __func__, tid->tid);
        ATH_TX_LOCK_ASSERT(sc);

        /*
         * XXX TODO: If we're called for a queue that we're leaking frames to,
         * ensure we only leak one.
         */

        tap = ath_tx_get_tx_tid(an, tid->tid);

        if (tid->tid == IEEE80211_NONQOS_TID)
                DPRINTF(sc, ATH_DEBUG_SW_TX, 
                    "%s: called for TID=NONQOS_TID?\n", __func__);

        for (;;) {
                status = ATH_AGGR_DONE;

                /*
                 * If the upper layer has paused the TID, don't
                 * queue any further packets.
                 *
                 * This can also occur from the completion task because
                 * of packet loss; but as its serialised with this code,
                 * it won't "appear" half way through queuing packets.
                 */
                if (! ath_tx_tid_can_tx_or_sched(sc, tid))
                        break;

                bf = ATH_TID_FIRST(tid);
                if (bf == NULL) {
                        break;
                }

                /*
                 * If the packet doesn't fall within the BAW (eg a NULL
                 * data frame), schedule it directly; continue.
                 */
                if (! bf->bf_state.bfs_dobaw) {
                        DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
                            "%s: non-baw packet\n",
                            __func__);
                        ATH_TID_REMOVE(tid, bf, bf_list);

                        if (bf->bf_state.bfs_nframes > 1)
                                DPRINTF(sc, ATH_DEBUG_SW_TX, 
                                    "%s: aggr=%d, nframes=%d\n",
                                    __func__,
                                    bf->bf_state.bfs_aggr,
                                    bf->bf_state.bfs_nframes);

                        /*
                         * This shouldn't happen - such frames shouldn't
                         * ever have been queued as an aggregate in the
                         * first place.  However, make sure the fields
                         * are correctly setup just to be totally sure.
                         */
                        bf->bf_state.bfs_aggr = 0;
                        bf->bf_state.bfs_nframes = 1;

                        /* Update CLRDMASK just before this frame is queued */
                        ath_tx_update_clrdmask(sc, tid, bf);

                        ath_tx_do_ratelookup(sc, bf);
                        ath_tx_calc_duration(sc, bf);
                        ath_tx_calc_protection(sc, bf);
                        ath_tx_set_rtscts(sc, bf);
                        ath_tx_rate_fill_rcflags(sc, bf);
                        ath_tx_setds(sc, bf);
                        ath_hal_clr11n_aggr(sc->sc_ah, bf->bf_desc);

                        sc->sc_aggr_stats.aggr_nonbaw_pkt++;

                        /* Queue the packet; continue */
                        goto queuepkt;
                }

                TAILQ_INIT(&bf_q);

                /*
                 * Do a rate control lookup on the first frame in the
                 * list. The rate control code needs that to occur
                 * before it can determine whether to TX.
                 * It's inaccurate because the rate control code doesn't
                 * really "do" aggregate lookups, so it only considers
                 * the size of the first frame.
                 */
                ath_tx_do_ratelookup(sc, bf);
                bf->bf_state.bfs_rc[3].rix = 0;
                bf->bf_state.bfs_rc[3].tries = 0;

                ath_tx_calc_duration(sc, bf);
                ath_tx_calc_protection(sc, bf);

                ath_tx_set_rtscts(sc, bf);
                ath_tx_rate_fill_rcflags(sc, bf);

                status = ath_tx_form_aggr(sc, an, tid, &bf_q);

                DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
                    "%s: ath_tx_form_aggr() status=%d\n", __func__, status);

                /*
                 * No frames to be picked up - out of BAW
                 */
                if (TAILQ_EMPTY(&bf_q))
                        break;

                /*
                 * This assumes that the descriptor list in the ath_bufhead
                 * are already linked together via bf_next pointers.
                 */
                bf = TAILQ_FIRST(&bf_q);

                if (status == ATH_AGGR_8K_LIMITED)
                        sc->sc_aggr_stats.aggr_rts_aggr_limited++;

                /*
                 * If it's the only frame send as non-aggregate
                 * assume that ath_tx_form_aggr() has checked
                 * whether it's in the BAW and added it appropriately.
                 */
                if (bf->bf_state.bfs_nframes == 1) {
                        DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
                            "%s: single-frame aggregate\n", __func__);

                        /* Update CLRDMASK just before this frame is queued */
                        ath_tx_update_clrdmask(sc, tid, bf);

                        bf->bf_state.bfs_aggr = 0;
                        bf->bf_state.bfs_ndelim = 0;
                        ath_tx_setds(sc, bf);
                        ath_hal_clr11n_aggr(sc->sc_ah, bf->bf_desc);
                        if (status == ATH_AGGR_BAW_CLOSED)
                                sc->sc_aggr_stats.aggr_baw_closed_single_pkt++;
                        else
                                sc->sc_aggr_stats.aggr_single_pkt++;
                } else {
                        DPRINTF(sc, ATH_DEBUG_SW_TX_AGGR,
                            "%s: multi-frame aggregate: %d frames, "
                            "length %d\n",
                             __func__, bf->bf_state.bfs_nframes,
                            bf->bf_state.bfs_al);
                        bf->bf_state.bfs_aggr = 1;
                        sc->sc_aggr_stats.aggr_pkts[bf->bf_state.bfs_nframes]++;
                        sc->sc_aggr_stats.aggr_aggr_pkt++;

                        /* Update CLRDMASK just before this frame is queued */
                        ath_tx_update_clrdmask(sc, tid, bf);

                        /*
                         * Calculate the duration/protection as required.
                         */
                        ath_tx_calc_duration(sc, bf);
                        ath_tx_calc_protection(sc, bf);

                        /*
                         * Update the rate and rtscts information based on the
                         * rate decision made by the rate control code;
                         * the first frame in the aggregate needs it.
                         */
                        ath_tx_set_rtscts(sc, bf);

                        /*
                         * Setup the relevant descriptor fields
                         * for aggregation. The first descriptor
                         * already points to the rest in the chain.
                         */
                        ath_tx_setds_11n(sc, bf);

                }
        queuepkt:
                /* Set completion handler, multi-frame aggregate or not */
                bf->bf_comp = ath_tx_aggr_comp;

                if (bf->bf_state.bfs_tid == IEEE80211_NONQOS_TID)
                        DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: TID=16?\n", __func__);

                /*
                 * Update leak count and frame config if were leaking frames.
                 *
                 * XXX TODO: it should update all frames in an aggregate
                 * correctly!
                 */
                ath_tx_leak_count_update(sc, tid, bf);

                /* Punt to txq */
                ath_tx_handoff(sc, txq, bf);

                /* Track outstanding buffer count to hardware */
                /* aggregates are "one" buffer */
                tid->hwq_depth++;

                /*
                 * Break out if ath_tx_form_aggr() indicated
                 * there can't be any further progress (eg BAW is full.)
                 * Checking for an empty txq is done above.
                 *
                 * XXX locking on txq here?
                 */
                /* XXX TXQ locking */
                if (txq->axq_aggr_depth >= sc->sc_hwq_limit_aggr ||
                    (status == ATH_AGGR_BAW_CLOSED ||
                     status == ATH_AGGR_LEAK_CLOSED))
                        break;
        }
}

/*
 * Schedule some packets from the given node/TID to the hardware.
 *
 * XXX TODO: this routine doesn't enforce the maximum TXQ depth.
 * It just dumps frames into the TXQ.  We should limit how deep
 * the transmit queue can grow for frames dispatched to the given
 * TXQ.
 *
 * To avoid locking issues, either we need to own the TXQ lock
 * at this point, or we need to pass in the maximum frame count
 * from the caller.
 */
void
ath_tx_tid_hw_queue_norm(struct ath_softc *sc, struct ath_node *an,
    struct ath_tid *tid)
{
        struct ath_buf *bf;
        struct ath_txq *txq = sc->sc_ac2q[tid->ac];

        DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: node %p: TID %d: called\n",
            __func__, an, tid->tid);

        ATH_TX_LOCK_ASSERT(sc);

        /* Check - is AMPDU pending or running? then print out something */
        if (ath_tx_ampdu_pending(sc, an, tid->tid))
                DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: tid=%d, ampdu pending?\n",
                    __func__, tid->tid);
        if (ath_tx_ampdu_running(sc, an, tid->tid))
                DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: tid=%d, ampdu running?\n",
                    __func__, tid->tid);

        for (;;) {

                /*
                 * If the upper layers have paused the TID, don't
                 * queue any further packets.
                 *
                 * XXX if we are leaking frames, make sure we decrement
                 * that counter _and_ we continue here.
                 */
                if (! ath_tx_tid_can_tx_or_sched(sc, tid))
                        break;

                bf = ATH_TID_FIRST(tid);
                if (bf == NULL) {
                        break;
                }

                ATH_TID_REMOVE(tid, bf, bf_list);

                /* Sanity check! */
                if (tid->tid != bf->bf_state.bfs_tid) {
                        DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: bfs_tid %d !="
                            " tid %d\n", __func__, bf->bf_state.bfs_tid,
                            tid->tid);
                }
                /* Normal completion handler */
                bf->bf_comp = ath_tx_normal_comp;

                /*
                 * Override this for now, until the non-aggregate
                 * completion handler correctly handles software retransmits.
                 */
                bf->bf_state.bfs_txflags |= HAL_TXDESC_CLRDMASK;

                /* Update CLRDMASK just before this frame is queued */
                ath_tx_update_clrdmask(sc, tid, bf);

                /* Program descriptors + rate control */
                ath_tx_do_ratelookup(sc, bf);
                ath_tx_calc_duration(sc, bf);
                ath_tx_calc_protection(sc, bf);
                ath_tx_set_rtscts(sc, bf);
                ath_tx_rate_fill_rcflags(sc, bf);
                ath_tx_setds(sc, bf);

                /*
                 * Update the current leak count if
                 * we're leaking frames; and set the
                 * MORE flag as appropriate.
                 */
                ath_tx_leak_count_update(sc, tid, bf);

                /* Track outstanding buffer count to hardware */
                /* aggregates are "one" buffer */
                tid->hwq_depth++;

                /* Punt to hardware or software txq */
                ath_tx_handoff(sc, txq, bf);
        }
}

/*
 * Schedule some packets to the given hardware queue.
 *
 * This function walks the list of TIDs (ie, ath_node TIDs
 * with queued traffic) and attempts to schedule traffic
 * from them.
 *
 * TID scheduling is implemented as a FIFO, with TIDs being
 * added to the end of the queue after some frames have been
 * scheduled.
 */
void
ath_txq_sched(struct ath_softc *sc, struct ath_txq *txq)
{
        struct ath_tid *tid, *next, *last;

        ATH_TX_LOCK_ASSERT(sc);

        /*
         * Don't schedule if the hardware queue is busy.
         * This (hopefully) gives some more time to aggregate
         * some packets in the aggregation queue.
         *
         * XXX It doesn't stop a parallel sender from sneaking
         * in transmitting a frame!
         */
        /* XXX TXQ locking */
        if (txq->axq_aggr_depth + txq->fifo.axq_depth >= sc->sc_hwq_limit_aggr) {
                sc->sc_aggr_stats.aggr_sched_nopkt++;
                return;
        }
        if (txq->axq_depth >= sc->sc_hwq_limit_nonaggr) {
                sc->sc_aggr_stats.aggr_sched_nopkt++;
                return;
        }

        last = TAILQ_LAST(&txq->axq_tidq, axq_t_s);

        TAILQ_FOREACH_SAFE(tid, &txq->axq_tidq, axq_qelem, next) {
                /*
                 * Suspend paused queues here; they'll be resumed
                 * once the addba completes or times out.
                 */
                DPRINTF(sc, ATH_DEBUG_SW_TX, "%s: tid=%d, paused=%d\n",
                    __func__, tid->tid, tid->paused);
                ath_tx_tid_unsched(sc, tid);
                /*
                 * This node may be in power-save and we're leaking
                 * a frame; be careful.
                 */
                if (! ath_tx_tid_can_tx_or_sched(sc, tid)) {
                        continue;
                }
                if (ath_tx_ampdu_running(sc, tid->an, tid->tid))
                        ath_tx_tid_hw_queue_aggr(sc, tid->an, tid);
                else
                        ath_tx_tid_hw_queue_norm(sc, tid->an, tid);

                /* Not empty? Re-schedule */
                if (tid->axq_depth != 0)
                        ath_tx_tid_sched(sc, tid);

                /*
                 * Give the software queue time to aggregate more
                 * packets.  If we aren't running aggregation then
                 * we should still limit the hardware queue depth.
                 */
                /* XXX TXQ locking */
                if (txq->axq_aggr_depth + txq->fifo.axq_depth >= sc->sc_hwq_limit_aggr) {
                        break;
                }
                if (txq->axq_depth >= sc->sc_hwq_limit_nonaggr) {
                        break;
                }

                /*
                 * If this was the last entry on the original list, stop.
                 * Otherwise nodes that have been rescheduled onto the end
                 * of the TID FIFO list will just keep being rescheduled.
                 *
                 * XXX What should we do about nodes that were paused
                 * but are pending a leaking frame in response to a ps-poll?
                 * They'll be put at the front of the list; so they'll
                 * prematurely trigger this condition! Ew.
                 */
                if (tid == last)
                        break;
        }
}

/*
 * TX addba handling
 */

/*
 * Return net80211 TID struct pointer, or NULL for none
 */
struct ieee80211_tx_ampdu *
ath_tx_get_tx_tid(struct ath_node *an, int tid)
{
        struct ieee80211_node *ni = &an->an_node;
        struct ieee80211_tx_ampdu *tap;

        if (tid == IEEE80211_NONQOS_TID)
                return NULL;

        tap = &ni->ni_tx_ampdu[tid];
        return tap;
}

/*
 * Is AMPDU-TX running?
 */
static int
ath_tx_ampdu_running(struct ath_softc *sc, struct ath_node *an, int tid)
{
        struct ieee80211_tx_ampdu *tap;

        if (tid == IEEE80211_NONQOS_TID)
                return 0;

        tap = ath_tx_get_tx_tid(an, tid);
        if (tap == NULL)
                return 0;       /* Not valid; default to not running */

        return !! (tap->txa_flags & IEEE80211_AGGR_RUNNING);
}

/*
 * Is AMPDU-TX negotiation pending?
 */
static int
ath_tx_ampdu_pending(struct ath_softc *sc, struct ath_node *an, int tid)
{
        struct ieee80211_tx_ampdu *tap;

        if (tid == IEEE80211_NONQOS_TID)
                return 0;

        tap = ath_tx_get_tx_tid(an, tid);
        if (tap == NULL)
                return 0;       /* Not valid; default to not pending */

        return !! (tap->txa_flags & IEEE80211_AGGR_XCHGPEND);
}

/*
 * Is AMPDU-TX pending for the given TID?
 */


/*
 * Method to handle sending an ADDBA request.
 *
 * We tap this so the relevant flags can be set to pause the TID
 * whilst waiting for the response.
 *
 * XXX there's no timeout handler we can override?
 */
int
ath_addba_request(struct ieee80211_node *ni, struct ieee80211_tx_ampdu *tap,
    int dialogtoken, int baparamset, int batimeout)
{
        struct ath_softc *sc = ni->ni_ic->ic_ifp->if_softc;
        int tid = tap->txa_tid;
        struct ath_node *an = ATH_NODE(ni);
        struct ath_tid *atid = &an->an_tid[tid];

        /*
         * XXX danger Will Robinson!
         *
         * Although the taskqueue may be running and scheduling some more
         * packets, these should all be _before_ the addba sequence number.
         * However, net80211 will keep self-assigning sequence numbers
         * until addba has been negotiated.
         *
         * In the past, these packets would be "paused" (which still works
         * fine, as they're being scheduled to the driver in the same
         * serialised method which is calling the addba request routine)
         * and when the aggregation session begins, they'll be dequeued
         * as aggregate packets and added to the BAW. However, now there's
         * a "bf->bf_state.bfs_dobaw" flag, and this isn't set for these
         * packets. Thus they never get included in the BAW tracking and
         * this can cause the initial burst of packets after the addba
         * negotiation to "hang", as they quickly fall outside the BAW.
         *
         * The "eventual" solution should be to tag these packets with
         * dobaw. Although net80211 has given us a sequence number,
         * it'll be "after" the left edge of the BAW and thus it'll
         * fall within it.
         */
        ATH_TX_LOCK(sc);
        /*
         * This is a bit annoying.  Until net80211 HT code inherits some
         * (any) locking, we may have this called in parallel BUT only
         * one response/timeout will be called.  Grr.
         */
        if (atid->addba_tx_pending == 0) {
                ath_tx_tid_pause(sc, atid);
                atid->addba_tx_pending = 1;
        }
        ATH_TX_UNLOCK(sc);

        DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL,
            "%s: %6D: called; dialogtoken=%d, baparamset=%d, batimeout=%d\n",
            __func__,
            ni->ni_macaddr,
            ":",
            dialogtoken, baparamset, batimeout);
        DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL,
            "%s: txa_start=%d, ni_txseqs=%d\n",
            __func__, tap->txa_start, ni->ni_txseqs[tid]);

        return sc->sc_addba_request(ni, tap, dialogtoken, baparamset,
            batimeout);
}

/*
 * Handle an ADDBA response.
 *
 * We unpause the queue so TX'ing can resume.
 *
 * Any packets TX'ed from this point should be "aggregate" (whether
 * aggregate or not) so the BAW is updated.
 *
 * Note! net80211 keeps self-assigning sequence numbers until
 * ampdu is negotiated. This means the initially-negotiated BAW left
 * edge won't match the ni->ni_txseq.
 *
 * So, being very dirty, the BAW left edge is "slid" here to match
 * ni->ni_txseq.
 *
 * What likely SHOULD happen is that all packets subsequent to the
 * addba request should be tagged as aggregate and queued as non-aggregate
 * frames; thus updating the BAW. For now though, I'll just slide the
 * window.
 */
int
ath_addba_response(struct ieee80211_node *ni, struct ieee80211_tx_ampdu *tap,
    int status, int code, int batimeout)
{
        struct ath_softc *sc = ni->ni_ic->ic_ifp->if_softc;
        int tid = tap->txa_tid;
        struct ath_node *an = ATH_NODE(ni);
        struct ath_tid *atid = &an->an_tid[tid];
        int r;

        DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL,
            "%s: %6D: called; status=%d, code=%d, batimeout=%d\n", __func__,
            ni->ni_macaddr,
            ":",
            status, code, batimeout);

        DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL,
            "%s: txa_start=%d, ni_txseqs=%d\n",
            __func__, tap->txa_start, ni->ni_txseqs[tid]);

        /*
         * Call this first, so the interface flags get updated
         * before the TID is unpaused. Otherwise a race condition
         * exists where the unpaused TID still doesn't yet have
         * IEEE80211_AGGR_RUNNING set.
         */
        r = sc->sc_addba_response(ni, tap, status, code, batimeout);

        ATH_TX_LOCK(sc);
        atid->addba_tx_pending = 0;
        /*
         * XXX dirty!
         * Slide the BAW left edge to wherever net80211 left it for us.
         * Read above for more information.
         */
        tap->txa_start = ni->ni_txseqs[tid];
        ath_tx_tid_resume(sc, atid);
        ATH_TX_UNLOCK(sc);
        return r;
}


/*
 * Stop ADDBA on a queue.
 *
 * This can be called whilst BAR TX is currently active on the queue,
 * so make sure this is unblocked before continuing.
 */
void
ath_addba_stop(struct ieee80211_node *ni, struct ieee80211_tx_ampdu *tap)
{
        struct ath_softc *sc = ni->ni_ic->ic_ifp->if_softc;
        int tid = tap->txa_tid;
        struct ath_node *an = ATH_NODE(ni);
        struct ath_tid *atid = &an->an_tid[tid];
        ath_bufhead bf_cq;
        struct ath_buf *bf;

        DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL, "%s: %6D: called\n",
            __func__,
            ni->ni_macaddr,
            ":");

        /*
         * Pause TID traffic early, so there aren't any races
         * Unblock the pending BAR held traffic, if it's currently paused.
         */
        ATH_TX_LOCK(sc);
        ath_tx_tid_pause(sc, atid);
        if (atid->bar_wait) {
                /*
                 * bar_unsuspend() expects bar_tx == 1, as it should be
                 * called from the TX completion path.  This quietens
                 * the warning.  It's cleared for us anyway.
                 */
                atid->bar_tx = 1;
                ath_tx_tid_bar_unsuspend(sc, atid);
        }
        ATH_TX_UNLOCK(sc);

        /* There's no need to hold the TXQ lock here */
        sc->sc_addba_stop(ni, tap);

        /*
         * ath_tx_tid_cleanup will resume the TID if possible, otherwise
         * it'll set the cleanup flag, and it'll be unpaused once
         * things have been cleaned up.
         */
        TAILQ_INIT(&bf_cq);
        ATH_TX_LOCK(sc);
        ath_tx_tid_cleanup(sc, an, tid, &bf_cq);
        /*
         * Unpause the TID if no cleanup is required.
         */
        if (! atid->cleanup_inprogress)
                ath_tx_tid_resume(sc, atid);
        ATH_TX_UNLOCK(sc);

        /* Handle completing frames and fail them */
        while ((bf = TAILQ_FIRST(&bf_cq)) != NULL) {
                TAILQ_REMOVE(&bf_cq, bf, bf_list);
                ath_tx_default_comp(sc, bf, 1);
        }

}

/*
 * Handle a node reassociation.
 *
 * We may have a bunch of frames queued to the hardware; those need
 * to be marked as cleanup.
 */
void
ath_tx_node_reassoc(struct ath_softc *sc, struct ath_node *an)
{
        struct ath_tid *tid;
        int i;
        ath_bufhead bf_cq;
        struct ath_buf *bf;

        TAILQ_INIT(&bf_cq);

        ATH_TX_UNLOCK_ASSERT(sc);

        ATH_TX_LOCK(sc);
        for (i = 0; i < IEEE80211_TID_SIZE; i++) {
                tid = &an->an_tid[i];
                if (tid->hwq_depth == 0)
                        continue;
                ath_tx_tid_pause(sc, tid);
                DPRINTF(sc, ATH_DEBUG_NODE,
                    "%s: %6D: TID %d: cleaning up TID\n",
                    __func__,
                    an->an_node.ni_macaddr,
                    ":",
                    i);
                ath_tx_tid_cleanup(sc, an, i, &bf_cq);
                /*
                 * Unpause the TID if no cleanup is required.
                 */
                if (! tid->cleanup_inprogress)
                        ath_tx_tid_resume(sc, tid);
        }
        ATH_TX_UNLOCK(sc);

        /* Handle completing frames and fail them */
        while ((bf = TAILQ_FIRST(&bf_cq)) != NULL) {
                TAILQ_REMOVE(&bf_cq, bf, bf_list);
                ath_tx_default_comp(sc, bf, 1);
        }
}

/*
 * Note: net80211 bar_timeout() doesn't call this function on BAR failure;
 * it simply tears down the aggregation session. Ew.
 *
 * It however will call ieee80211_ampdu_stop() which will call
 * ic->ic_addba_stop().
 *
 * XXX This uses a hard-coded max BAR count value; the whole
 * XXX BAR TX success or failure should be better handled!
 */
void
ath_bar_response(struct ieee80211_node *ni, struct ieee80211_tx_ampdu *tap,
    int status)
{
        struct ath_softc *sc = ni->ni_ic->ic_ifp->if_softc;
        int tid = tap->txa_tid;
        struct ath_node *an = ATH_NODE(ni);
        struct ath_tid *atid = &an->an_tid[tid];
        int attempts = tap->txa_attempts;

        DPRINTF(sc, ATH_DEBUG_SW_TX_BAR,
            "%s: %6D: called; txa_tid=%d, atid->tid=%d, status=%d, attempts=%d\n",
            __func__,
            ni->ni_macaddr,
            ":",
            tap->txa_tid,
            atid->tid,
            status,
            attempts);

        /* Note: This may update the BAW details */
        sc->sc_bar_response(ni, tap, status);

        /* Unpause the TID */
        /*
         * XXX if this is attempt=50, the TID will be downgraded
         * XXX to a non-aggregate session. So we must unpause the
         * XXX TID here or it'll never be done.
         *
         * Also, don't call it if bar_tx/bar_wait are 0; something
         * has beaten us to the punch? (XXX figure out what?)
         */
        if (status == 0 || attempts == 50) {
                ATH_TX_LOCK(sc);
                if (atid->bar_tx == 0 || atid->bar_wait == 0)
                        DPRINTF(sc, ATH_DEBUG_SW_TX_BAR,
                            "%s: huh? bar_tx=%d, bar_wait=%d\n",
                            __func__,
                            atid->bar_tx, atid->bar_wait);
                else
                        ath_tx_tid_bar_unsuspend(sc, atid);
                ATH_TX_UNLOCK(sc);
        }
}

/*
 * This is called whenever the pending ADDBA request times out.
 * Unpause and reschedule the TID.
 */
void
ath_addba_response_timeout(struct ieee80211_node *ni,
    struct ieee80211_tx_ampdu *tap)
{
        struct ath_softc *sc = ni->ni_ic->ic_ifp->if_softc;
        int tid = tap->txa_tid;
        struct ath_node *an = ATH_NODE(ni);
        struct ath_tid *atid = &an->an_tid[tid];

        DPRINTF(sc, ATH_DEBUG_SW_TX_CTRL,
            "%s: %6D: TID=%d, called; resuming\n",
            __func__,
            ni->ni_macaddr,
            ":",
            tid);

        ATH_TX_LOCK(sc);
        atid->addba_tx_pending = 0;
        ATH_TX_UNLOCK(sc);

        /* Note: This updates the aggregate state to (again) pending */
        sc->sc_addba_response_timeout(ni, tap);

        /* Unpause the TID; which reschedules it */
        ATH_TX_LOCK(sc);
        ath_tx_tid_resume(sc, atid);
        ATH_TX_UNLOCK(sc);
}

/*
 * Check if a node is asleep or not.
 */
int
ath_tx_node_is_asleep(struct ath_softc *sc, struct ath_node *an)
{

        ATH_TX_LOCK_ASSERT(sc);

        return (an->an_is_powersave);
}

/*
 * Mark a node as currently "in powersaving."
 * This suspends all traffic on the node.
 *
 * This must be called with the node/tx locks free.
 *
 * XXX TODO: the locking silliness below is due to how the node
 * locking currently works.  Right now, the node lock is grabbed
 * to do rate control lookups and these are done with the TX
 * queue lock held.  This means the node lock can't be grabbed
 * first here or a LOR will occur.
 *
 * Eventually (hopefully!) the TX path code will only grab
 * the TXQ lock when transmitting and the ath_node lock when
 * doing node/TID operations.  There are other complications -
 * the sched/unsched operations involve walking the per-txq
 * 'active tid' list and this requires both locks to be held.
 */
void
ath_tx_node_sleep(struct ath_softc *sc, struct ath_node *an)
{
        struct ath_tid *atid;
        struct ath_txq *txq;
        int tid;

        ATH_TX_UNLOCK_ASSERT(sc);

        /* Suspend all traffic on the node */
        ATH_TX_LOCK(sc);

        if (an->an_is_powersave) {
                DPRINTF(sc, ATH_DEBUG_XMIT,
                    "%s: %6D: node was already asleep!\n",
                    __func__, an->an_node.ni_macaddr, ":");
                ATH_TX_UNLOCK(sc);
                return;
        }

        for (tid = 0; tid < IEEE80211_TID_SIZE; tid++) {
                atid = &an->an_tid[tid];
                txq = sc->sc_ac2q[atid->ac];

                ath_tx_tid_pause(sc, atid);
        }

        /* Mark node as in powersaving */
        an->an_is_powersave = 1;

        ATH_TX_UNLOCK(sc);
}

/*
 * Mark a node as currently "awake."
 * This resumes all traffic to the node.
 */
void
ath_tx_node_wakeup(struct ath_softc *sc, struct ath_node *an)
{
        struct ath_tid *atid;
        struct ath_txq *txq;
        int tid;

        ATH_TX_UNLOCK_ASSERT(sc);

        ATH_TX_LOCK(sc);

        /* !? */
        if (an->an_is_powersave == 0) {
                ATH_TX_UNLOCK(sc);
                DPRINTF(sc, ATH_DEBUG_XMIT,
                    "%s: an=%p: node was already awake\n",
                    __func__, an);
                return;
        }

        /* Mark node as awake */
        an->an_is_powersave = 0;
        /*
         * Clear any pending leaked frame requests
         */
        an->an_leak_count = 0;

        for (tid = 0; tid < IEEE80211_TID_SIZE; tid++) {
                atid = &an->an_tid[tid];
                txq = sc->sc_ac2q[atid->ac];

                ath_tx_tid_resume(sc, atid);
        }
        ATH_TX_UNLOCK(sc);
}

static int
ath_legacy_dma_txsetup(struct ath_softc *sc)
{

        /* nothing new needed */
        return (0);
}

static int
ath_legacy_dma_txteardown(struct ath_softc *sc)
{

        /* nothing new needed */
        return (0);
}

void
ath_xmit_setup_legacy(struct ath_softc *sc)
{
        /*
         * For now, just set the descriptor length to sizeof(ath_desc);
         * worry about extracting the real length out of the HAL later.
         */
        sc->sc_tx_desclen = sizeof(struct ath_desc);
        sc->sc_tx_statuslen = sizeof(struct ath_desc);
        sc->sc_tx_nmaps = 1;    /* only one buffer per TX desc */

        sc->sc_tx.xmit_setup = ath_legacy_dma_txsetup;
        sc->sc_tx.xmit_teardown = ath_legacy_dma_txteardown;
        sc->sc_tx.xmit_attach_comp_func = ath_legacy_attach_comp_func;

        sc->sc_tx.xmit_dma_restart = ath_legacy_tx_dma_restart;
        sc->sc_tx.xmit_handoff = ath_legacy_xmit_handoff;

        sc->sc_tx.xmit_drain = ath_legacy_tx_drain;
}