2 * Copyright (c) 1992, 1993 Erik Forsberg.
3 * Copyright (c) 1996, 1997 Kazutaka YOKOTA.
6 * Redistribution and use in source and binary forms, with or without
7 * modification, are permitted provided that the following conditions
9 * 1. Redistributions of source code must retain the above copyright
10 * notice, this list of conditions and the following disclaimer.
12 * THIS SOFTWARE IS PROVIDED BY ``AS IS'' AND ANY EXPRESS OR IMPLIED
13 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
14 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
15 * NO EVENT SHALL I BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
16 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
17 * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
18 * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
19 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
20 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
21 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
24 * Ported to 386bsd Oct 17, 1992
25 * Sandi Donno, Computer Science, University of Cape Town, South Africa
26 * Please send bug reports to sandi@cs.uct.ac.za
28 * Thanks are also due to Rick Macklem, rick@snowhite.cis.uoguelph.ca -
29 * although I was only partially successful in getting the alpha release
30 * of his "driver for the Logitech and ATI Inport Bus mice for use with
31 * 386bsd and the X386 port" to work with my Microsoft mouse, I nevertheless
32 * found his code to be an invaluable reference when porting this driver
35 * Further modifications for latest 386BSD+patchkit and port to NetBSD,
36 * Andrew Herbert <andrew@werple.apana.org.au> - 8 June 1993
38 * Cloned from the Microsoft Bus Mouse driver, also by Erik Forsberg, by
39 * Andrew Herbert - 12 June 1993
41 * Modified for PS/2 mouse by Charles Hannum <mycroft@ai.mit.edu>
44 * Modified for PS/2 AUX mouse by Shoji Yuen <yuen@nuie.nagoya-u.ac.jp>
47 * Hardware access routines and probe logic rewritten by
48 * Kazutaka Yokota <yokota@zodiac.mech.utsunomiya-u.ac.jp>
49 * - 3, 14, 22 October 1996.
50 * - 12 November 1996. IOCTLs and rearranging `psmread', `psmioctl'...
51 * - 14, 30 November 1996. Uses `kbdio.c'.
52 * - 13 December 1996. Uses queuing version of `kbdio.c'.
53 * - January/February 1997. Tweaked probe logic for
54 * HiNote UltraII/Latitude/Armada laptops.
55 * - 30 July 1997. Added APM support.
56 * - 5 March 1997. Defined driver configuration flags (PSM_CONFIG_XXX).
57 * Improved sync check logic.
58 * Vendor specific support routines.
61 #include <sys/cdefs.h>
62 __FBSDID("$FreeBSD$");
67 #include <sys/param.h>
68 #include <sys/systm.h>
69 #include <sys/kernel.h>
70 #include <sys/module.h>
73 #include <sys/filio.h>
75 #include <sys/sigio.h>
76 #include <sys/signalvar.h>
77 #include <sys/syslog.h>
78 #include <machine/bus.h>
80 #include <sys/selinfo.h>
81 #include <sys/sysctl.h>
85 #include <sys/limits.h>
86 #include <sys/mouse.h>
87 #include <machine/resource.h>
90 #include <isa/isavar.h>
93 #include <dev/atkbdc/atkbdcreg.h>
94 #include <dev/atkbdc/psm.h>
97 * Driver specific options: the following options may be set by
98 * `options' statements in the kernel configuration file.
103 #define PSM_DEBUG 0 /*
104 * logging: 0: none, 1: brief, 2: verbose
105 * 3: sync errors, 4: all packets
108 #define VLOG(level, args) do { \
109 if (verbose >= level) \
113 #ifndef PSM_INPUT_TIMEOUT
114 #define PSM_INPUT_TIMEOUT 2000000 /* 2 sec */
117 #ifndef PSM_TAP_TIMEOUT
118 #define PSM_TAP_TIMEOUT 125000
121 #ifndef PSM_TAP_THRESHOLD
122 #define PSM_TAP_THRESHOLD 25
125 /* end of driver specific options */
127 #define PSMCPNP_DRIVER_NAME "psmcpnp"
130 #define PSM_BUFSIZE 960
131 #define PSM_SMALLBUFSIZE 240
133 /* operation levels */
134 #define PSM_LEVEL_BASE 0
135 #define PSM_LEVEL_STANDARD 1
136 #define PSM_LEVEL_NATIVE 2
137 #define PSM_LEVEL_MIN PSM_LEVEL_BASE
138 #define PSM_LEVEL_MAX PSM_LEVEL_NATIVE
140 /* Logitech PS2++ protocol */
141 #define MOUSE_PS2PLUS_CHECKBITS(b) \
142 ((((b[2] & 0x03) << 2) | 0x02) == (b[1] & 0x0f))
143 #define MOUSE_PS2PLUS_PACKET_TYPE(b) \
144 (((b[0] & 0x30) >> 2) | ((b[1] & 0x30) >> 4))
147 typedef struct ringbuf {
148 int count; /* # of valid elements in the buffer */
149 int head; /* head pointer */
150 int tail; /* tail poiner */
151 u_char buf[PSM_BUFSIZE];
155 typedef struct packetbuf {
156 u_char ipacket[16]; /* interim input buffer */
157 int inputbytes; /* # of bytes in the input buffer */
160 #ifndef PSM_PACKETQUEUE
161 #define PSM_PACKETQUEUE 128
165 SYNAPTICS_SYSCTL_MIN_PRESSURE,
166 SYNAPTICS_SYSCTL_MAX_PRESSURE,
167 SYNAPTICS_SYSCTL_MAX_WIDTH,
168 SYNAPTICS_SYSCTL_MARGIN_TOP,
169 SYNAPTICS_SYSCTL_MARGIN_RIGHT,
170 SYNAPTICS_SYSCTL_MARGIN_BOTTOM,
171 SYNAPTICS_SYSCTL_MARGIN_LEFT,
172 SYNAPTICS_SYSCTL_NA_TOP,
173 SYNAPTICS_SYSCTL_NA_RIGHT,
174 SYNAPTICS_SYSCTL_NA_BOTTOM,
175 SYNAPTICS_SYSCTL_NA_LEFT,
176 SYNAPTICS_SYSCTL_WINDOW_MIN,
177 SYNAPTICS_SYSCTL_WINDOW_MAX,
178 SYNAPTICS_SYSCTL_MULTIPLICATOR,
179 SYNAPTICS_SYSCTL_WEIGHT_CURRENT,
180 SYNAPTICS_SYSCTL_WEIGHT_PREVIOUS,
181 SYNAPTICS_SYSCTL_WEIGHT_PREVIOUS_NA,
182 SYNAPTICS_SYSCTL_WEIGHT_LEN_SQUARED,
183 SYNAPTICS_SYSCTL_DIV_MIN,
184 SYNAPTICS_SYSCTL_DIV_MAX,
185 SYNAPTICS_SYSCTL_DIV_MAX_NA,
186 SYNAPTICS_SYSCTL_DIV_LEN,
187 SYNAPTICS_SYSCTL_TAP_MAX_DELTA,
188 SYNAPTICS_SYSCTL_TAP_MIN_QUEUE,
189 SYNAPTICS_SYSCTL_TAPHOLD_TIMEOUT,
190 SYNAPTICS_SYSCTL_VSCROLL_HOR_AREA,
191 SYNAPTICS_SYSCTL_VSCROLL_VER_AREA,
192 SYNAPTICS_SYSCTL_VSCROLL_MIN_DELTA,
193 SYNAPTICS_SYSCTL_VSCROLL_DIV_MIN,
194 SYNAPTICS_SYSCTL_VSCROLL_DIV_MAX
197 typedef struct synapticsinfo {
198 struct sysctl_ctx_list sysctl_ctx;
199 struct sysctl_oid *sysctl_tree;
200 int directional_scrolls;
217 int weight_previous_na;
218 int weight_len_squared;
226 int vscroll_ver_area;
227 int vscroll_hor_area;
228 int vscroll_min_delta;
233 typedef struct synapticspacket {
238 #define SYNAPTICS_PACKETQUEUE 10
239 #define SYNAPTICS_QUEUE_CURSOR(x) \
240 (x + SYNAPTICS_PACKETQUEUE) % SYNAPTICS_PACKETQUEUE
242 #define SYNAPTICS_VERSION_GE(synhw, major, minor) \
243 ((synhw).infoMajor > (major) || \
244 ((synhw).infoMajor == (major) && (synhw).infoMinor >= (minor)))
246 typedef struct synapticsaction {
247 synapticspacket_t queue[SYNAPTICS_PACKETQUEUE];
264 TRACKPOINT_SYSCTL_SENSITIVITY,
265 TRACKPOINT_SYSCTL_NEGATIVE_INERTIA,
266 TRACKPOINT_SYSCTL_UPPER_PLATEAU,
267 TRACKPOINT_SYSCTL_BACKUP_RANGE,
268 TRACKPOINT_SYSCTL_DRAG_HYSTERESIS,
269 TRACKPOINT_SYSCTL_MINIMUM_DRAG,
270 TRACKPOINT_SYSCTL_UP_THRESHOLD,
271 TRACKPOINT_SYSCTL_THRESHOLD,
272 TRACKPOINT_SYSCTL_JENKS_CURVATURE,
273 TRACKPOINT_SYSCTL_Z_TIME,
274 TRACKPOINT_SYSCTL_PRESS_TO_SELECT,
275 TRACKPOINT_SYSCTL_SKIP_BACKUPS
278 typedef struct trackpointinfo {
279 struct sysctl_ctx_list sysctl_ctx;
280 struct sysctl_oid *sysctl_tree;
295 /* driver control block */
296 struct psm_softc { /* Driver status information */
298 struct selinfo rsel; /* Process selecting for Input */
299 u_char state; /* Mouse driver state */
300 int config; /* driver configuration flags */
301 int flags; /* other flags */
302 KBDC kbdc; /* handle to access kbd controller */
303 struct resource *intr; /* IRQ resource */
304 void *ih; /* interrupt handle */
305 mousehw_t hw; /* hardware information */
306 synapticshw_t synhw; /* Synaptics hardware information */
307 synapticsinfo_t syninfo; /* Synaptics configuration */
308 synapticsaction_t synaction; /* Synaptics action context */
309 int tphw; /* TrackPoint hardware information */
310 trackpointinfo_t tpinfo; /* TrackPoint configuration */
311 mousemode_t mode; /* operation mode */
312 mousemode_t dflt_mode; /* default operation mode */
313 mousestatus_t status; /* accumulated mouse movement */
314 ringbuf_t queue; /* mouse status queue */
315 packetbuf_t pqueue[PSM_PACKETQUEUE]; /* mouse data queue */
316 int pqueue_start; /* start of data in queue */
317 int pqueue_end; /* end of data in queue */
318 int button; /* the latest button state */
319 int xold; /* previous absolute X position */
320 int yold; /* previous absolute Y position */
321 int xaverage; /* average X position */
322 int yaverage; /* average Y position */
323 int squelch; /* level to filter movement at low speed */
324 int zmax; /* maximum pressure value for touchpads */
325 int syncerrors; /* # of bytes discarded to synchronize */
326 int pkterrors; /* # of packets failed during quaranteen. */
327 struct timeval inputtimeout;
328 struct timeval lastsoftintr; /* time of last soft interrupt */
329 struct timeval lastinputerr; /* time last sync error happened */
330 struct timeval taptimeout; /* tap timeout for touchpads */
331 int watchdog; /* watchdog timer flag */
332 struct callout_handle callout; /* watchdog timer call out */
333 struct callout_handle softcallout; /* buffer timer call out */
338 struct sigio *async; /* Processes waiting for SIGIO */
340 static devclass_t psm_devclass;
342 /* driver state flags (state) */
343 #define PSM_VALID 0x80
344 #define PSM_OPEN 1 /* Device is open */
345 #define PSM_ASLP 2 /* Waiting for mouse data */
346 #define PSM_SOFTARMED 4 /* Software interrupt armed */
347 #define PSM_NEED_SYNCBITS 8 /* Set syncbits using next data pkt */
349 /* driver configuration flags (config) */
350 #define PSM_CONFIG_RESOLUTION 0x000f /* resolution */
351 #define PSM_CONFIG_ACCEL 0x00f0 /* acceleration factor */
352 #define PSM_CONFIG_NOCHECKSYNC 0x0100 /* disable sync. test */
353 #define PSM_CONFIG_NOIDPROBE 0x0200 /* disable mouse model probe */
354 #define PSM_CONFIG_NORESET 0x0400 /* don't reset the mouse */
355 #define PSM_CONFIG_FORCETAP 0x0800 /* assume `tap' action exists */
356 #define PSM_CONFIG_IGNPORTERROR 0x1000 /* ignore error in aux port test */
357 #define PSM_CONFIG_HOOKRESUME 0x2000 /* hook the system resume event */
358 #define PSM_CONFIG_INITAFTERSUSPEND 0x4000 /* init the device at the resume event */
360 #define PSM_CONFIG_FLAGS \
361 (PSM_CONFIG_RESOLUTION | \
363 PSM_CONFIG_NOCHECKSYNC | \
364 PSM_CONFIG_NOIDPROBE | \
365 PSM_CONFIG_NORESET | \
366 PSM_CONFIG_FORCETAP | \
367 PSM_CONFIG_IGNPORTERROR | \
368 PSM_CONFIG_HOOKRESUME | \
369 PSM_CONFIG_INITAFTERSUSPEND)
371 /* other flags (flags) */
372 #define PSM_FLAGS_FINGERDOWN 0x0001 /* VersaPad finger down */
375 static int tap_enabled = -1;
376 TUNABLE_INT("hw.psm.tap_enabled", &tap_enabled);
378 static int synaptics_support = 0;
379 TUNABLE_INT("hw.psm.synaptics_support", &synaptics_support);
381 static int trackpoint_support = 0;
382 TUNABLE_INT("hw.psm.trackpoint_support", &trackpoint_support);
384 static int verbose = PSM_DEBUG;
385 TUNABLE_INT("debug.psm.loglevel", &verbose);
387 /* for backward compatibility */
388 #define OLD_MOUSE_GETHWINFO _IOR('M', 1, old_mousehw_t)
389 #define OLD_MOUSE_GETMODE _IOR('M', 2, old_mousemode_t)
390 #define OLD_MOUSE_SETMODE _IOW('M', 3, old_mousemode_t)
392 typedef struct old_mousehw {
399 typedef struct old_mousemode {
406 /* packet formatting function */
407 typedef int packetfunc_t(struct psm_softc *, u_char *, int *, int,
410 /* function prototypes */
411 static void psmidentify(driver_t *, device_t);
412 static int psmprobe(device_t);
413 static int psmattach(device_t);
414 static int psmdetach(device_t);
415 static int psmresume(device_t);
417 static d_open_t psmopen;
418 static d_close_t psmclose;
419 static d_read_t psmread;
420 static d_write_t psmwrite;
421 static d_ioctl_t psmioctl;
422 static d_poll_t psmpoll;
424 static int enable_aux_dev(KBDC);
425 static int disable_aux_dev(KBDC);
426 static int get_mouse_status(KBDC, int *, int, int);
427 static int get_aux_id(KBDC);
428 static int set_mouse_sampling_rate(KBDC, int);
429 static int set_mouse_scaling(KBDC, int);
430 static int set_mouse_resolution(KBDC, int);
431 static int set_mouse_mode(KBDC);
432 static int get_mouse_buttons(KBDC);
433 static int is_a_mouse(int);
434 static void recover_from_error(KBDC);
435 static int restore_controller(KBDC, int);
436 static int doinitialize(struct psm_softc *, mousemode_t *);
437 static int doopen(struct psm_softc *, int);
438 static int reinitialize(struct psm_softc *, int);
439 static char *model_name(int);
440 static void psmsoftintr(void *);
441 static void psmintr(void *);
442 static void psmtimeout(void *);
443 static int timeelapsed(const struct timeval *, int, int,
444 const struct timeval *);
445 static void dropqueue(struct psm_softc *);
446 static void flushpackets(struct psm_softc *);
447 static void proc_mmanplus(struct psm_softc *, packetbuf_t *,
448 mousestatus_t *, int *, int *, int *);
449 static int proc_synaptics(struct psm_softc *, packetbuf_t *,
450 mousestatus_t *, int *, int *, int *);
451 static void proc_versapad(struct psm_softc *, packetbuf_t *,
452 mousestatus_t *, int *, int *, int *);
453 static int tame_mouse(struct psm_softc *, packetbuf_t *, mousestatus_t *,
456 /* vendor specific features */
457 typedef int probefunc_t(KBDC, struct psm_softc *);
459 static int mouse_id_proc1(KBDC, int, int, int *);
460 static int mouse_ext_command(KBDC, int);
462 static probefunc_t enable_groller;
463 static probefunc_t enable_gmouse;
464 static probefunc_t enable_aglide;
465 static probefunc_t enable_kmouse;
466 static probefunc_t enable_msexplorer;
467 static probefunc_t enable_msintelli;
468 static probefunc_t enable_4dmouse;
469 static probefunc_t enable_4dplus;
470 static probefunc_t enable_mmanplus;
471 static probefunc_t enable_synaptics;
472 static probefunc_t enable_trackpoint;
473 static probefunc_t enable_versapad;
479 probefunc_t *probefunc;
482 * WARNING: the order of probe is very important. Don't mess it
483 * unless you know what you are doing.
485 { MOUSE_MODEL_NET, /* Genius NetMouse */
486 0x08, MOUSE_PS2INTELLI_PACKETSIZE, enable_gmouse },
487 { MOUSE_MODEL_NETSCROLL, /* Genius NetScroll */
488 0xc8, 6, enable_groller },
489 { MOUSE_MODEL_MOUSEMANPLUS, /* Logitech MouseMan+ */
490 0x08, MOUSE_PS2_PACKETSIZE, enable_mmanplus },
491 { MOUSE_MODEL_EXPLORER, /* Microsoft IntelliMouse Explorer */
492 0x08, MOUSE_PS2INTELLI_PACKETSIZE, enable_msexplorer },
493 { MOUSE_MODEL_4D, /* A4 Tech 4D Mouse */
494 0x08, MOUSE_4D_PACKETSIZE, enable_4dmouse },
495 { MOUSE_MODEL_4DPLUS, /* A4 Tech 4D+ Mouse */
496 0xc8, MOUSE_4DPLUS_PACKETSIZE, enable_4dplus },
497 { MOUSE_MODEL_SYNAPTICS, /* Synaptics Touchpad */
498 0xc0, MOUSE_SYNAPTICS_PACKETSIZE, enable_synaptics },
499 { MOUSE_MODEL_INTELLI, /* Microsoft IntelliMouse */
500 0x08, MOUSE_PS2INTELLI_PACKETSIZE, enable_msintelli },
501 { MOUSE_MODEL_GLIDEPOINT, /* ALPS GlidePoint */
502 0xc0, MOUSE_PS2_PACKETSIZE, enable_aglide },
503 { MOUSE_MODEL_THINK, /* Kensington ThinkingMouse */
504 0x80, MOUSE_PS2_PACKETSIZE, enable_kmouse },
505 { MOUSE_MODEL_VERSAPAD, /* Interlink electronics VersaPad */
506 0xe8, MOUSE_PS2VERSA_PACKETSIZE, enable_versapad },
507 { MOUSE_MODEL_TRACKPOINT, /* IBM/Lenovo TrackPoint */
508 0xc0, MOUSE_PS2_PACKETSIZE, enable_trackpoint },
509 { MOUSE_MODEL_GENERIC,
510 0xc0, MOUSE_PS2_PACKETSIZE, NULL },
512 #define GENERIC_MOUSE_ENTRY \
513 ((sizeof(vendortype) / sizeof(*vendortype)) - 1)
515 /* device driver declarateion */
516 static device_method_t psm_methods[] = {
517 /* Device interface */
518 DEVMETHOD(device_identify, psmidentify),
519 DEVMETHOD(device_probe, psmprobe),
520 DEVMETHOD(device_attach, psmattach),
521 DEVMETHOD(device_detach, psmdetach),
522 DEVMETHOD(device_resume, psmresume),
527 static driver_t psm_driver = {
530 sizeof(struct psm_softc),
533 static struct cdevsw psm_cdevsw = {
534 .d_version = D_VERSION,
535 .d_flags = D_NEEDGIANT,
542 .d_name = PSM_DRIVER_NAME,
545 /* device I/O routines */
547 enable_aux_dev(KBDC kbdc)
551 res = send_aux_command(kbdc, PSMC_ENABLE_DEV);
552 VLOG(2, (LOG_DEBUG, "psm: ENABLE_DEV return code:%04x\n", res));
554 return (res == PSM_ACK);
558 disable_aux_dev(KBDC kbdc)
562 res = send_aux_command(kbdc, PSMC_DISABLE_DEV);
563 VLOG(2, (LOG_DEBUG, "psm: DISABLE_DEV return code:%04x\n", res));
565 return (res == PSM_ACK);
569 get_mouse_status(KBDC kbdc, int *status, int flag, int len)
578 cmd = PSMC_SEND_DEV_STATUS;
581 cmd = PSMC_SEND_DEV_DATA;
584 empty_aux_buffer(kbdc, 5);
585 res = send_aux_command(kbdc, cmd);
586 VLOG(2, (LOG_DEBUG, "psm: SEND_AUX_DEV_%s return code:%04x\n",
587 (flag == 1) ? "DATA" : "STATUS", res));
591 for (i = 0; i < len; ++i) {
592 status[i] = read_aux_data(kbdc);
597 VLOG(1, (LOG_DEBUG, "psm: %s %02x %02x %02x\n",
598 (flag == 1) ? "data" : "status", status[0], status[1], status[2]));
604 get_aux_id(KBDC kbdc)
609 empty_aux_buffer(kbdc, 5);
610 res = send_aux_command(kbdc, PSMC_SEND_DEV_ID);
611 VLOG(2, (LOG_DEBUG, "psm: SEND_DEV_ID return code:%04x\n", res));
618 id = read_aux_data(kbdc);
619 VLOG(2, (LOG_DEBUG, "psm: device ID: %04x\n", id));
625 set_mouse_sampling_rate(KBDC kbdc, int rate)
629 res = send_aux_command_and_data(kbdc, PSMC_SET_SAMPLING_RATE, rate);
630 VLOG(2, (LOG_DEBUG, "psm: SET_SAMPLING_RATE (%d) %04x\n", rate, res));
632 return ((res == PSM_ACK) ? rate : -1);
636 set_mouse_scaling(KBDC kbdc, int scale)
643 scale = PSMC_SET_SCALING11;
646 scale = PSMC_SET_SCALING21;
649 res = send_aux_command(kbdc, scale);
650 VLOG(2, (LOG_DEBUG, "psm: SET_SCALING%s return code:%04x\n",
651 (scale == PSMC_SET_SCALING21) ? "21" : "11", res));
653 return (res == PSM_ACK);
656 /* `val' must be 0 through PSMD_MAX_RESOLUTION */
658 set_mouse_resolution(KBDC kbdc, int val)
662 res = send_aux_command_and_data(kbdc, PSMC_SET_RESOLUTION, val);
663 VLOG(2, (LOG_DEBUG, "psm: SET_RESOLUTION (%d) %04x\n", val, res));
665 return ((res == PSM_ACK) ? val : -1);
669 * NOTE: once `set_mouse_mode()' is called, the mouse device must be
670 * re-enabled by calling `enable_aux_dev()'
673 set_mouse_mode(KBDC kbdc)
677 res = send_aux_command(kbdc, PSMC_SET_STREAM_MODE);
678 VLOG(2, (LOG_DEBUG, "psm: SET_STREAM_MODE return code:%04x\n", res));
680 return (res == PSM_ACK);
684 get_mouse_buttons(KBDC kbdc)
686 int c = 2; /* assume two buttons by default */
690 * NOTE: a special sequence to obtain Logitech Mouse specific
691 * information: set resolution to 25 ppi, set scaling to 1:1, set
692 * scaling to 1:1, set scaling to 1:1. Then the second byte of the
693 * mouse status bytes is the number of available buttons.
694 * Some manufactures also support this sequence.
696 if (set_mouse_resolution(kbdc, PSMD_RES_LOW) != PSMD_RES_LOW)
698 if (set_mouse_scaling(kbdc, 1) && set_mouse_scaling(kbdc, 1) &&
699 set_mouse_scaling(kbdc, 1) &&
700 get_mouse_status(kbdc, status, 0, 3) >= 3 && status[1] != 0)
705 /* misc subroutines */
707 * Someday, I will get the complete list of valid pointing devices and
714 static int valid_ids[] = {
715 PSM_MOUSE_ID, /* mouse */
716 PSM_BALLPOINT_ID, /* ballpoint device */
717 PSM_INTELLI_ID, /* Intellimouse */
718 PSM_EXPLORER_ID, /* Intellimouse Explorer */
719 -1 /* end of table */
723 for (i = 0; valid_ids[i] >= 0; ++i)
724 if (valid_ids[i] == id)
733 model_name(int model)
739 { MOUSE_MODEL_NETSCROLL, "NetScroll" },
740 { MOUSE_MODEL_NET, "NetMouse/NetScroll Optical" },
741 { MOUSE_MODEL_GLIDEPOINT, "GlidePoint" },
742 { MOUSE_MODEL_THINK, "ThinkingMouse" },
743 { MOUSE_MODEL_INTELLI, "IntelliMouse" },
744 { MOUSE_MODEL_MOUSEMANPLUS, "MouseMan+" },
745 { MOUSE_MODEL_VERSAPAD, "VersaPad" },
746 { MOUSE_MODEL_EXPLORER, "IntelliMouse Explorer" },
747 { MOUSE_MODEL_4D, "4D Mouse" },
748 { MOUSE_MODEL_4DPLUS, "4D+ Mouse" },
749 { MOUSE_MODEL_SYNAPTICS, "Synaptics Touchpad" },
750 { MOUSE_MODEL_TRACKPOINT, "IBM/Lenovo TrackPoint" },
751 { MOUSE_MODEL_GENERIC, "Generic PS/2 mouse" },
752 { MOUSE_MODEL_UNKNOWN, "Unknown" },
756 for (i = 0; models[i].model_code != MOUSE_MODEL_UNKNOWN; ++i)
757 if (models[i].model_code == model)
759 return (models[i].model_name);
763 recover_from_error(KBDC kbdc)
765 /* discard anything left in the output buffer */
766 empty_both_buffers(kbdc, 10);
770 * NOTE: KBDC_RESET_KBD may not restore the communication between the
771 * keyboard and the controller.
776 * NOTE: somehow diagnostic and keyboard port test commands bring the
779 if (!test_controller(kbdc))
780 log(LOG_ERR, "psm: keyboard controller failed.\n");
781 /* if there isn't a keyboard in the system, the following error is OK */
782 if (test_kbd_port(kbdc) != 0)
783 VLOG(1, (LOG_ERR, "psm: keyboard port failed.\n"));
788 restore_controller(KBDC kbdc, int command_byte)
790 empty_both_buffers(kbdc, 10);
792 if (!set_controller_command_byte(kbdc, 0xff, command_byte)) {
793 log(LOG_ERR, "psm: failed to restore the keyboard controller "
795 empty_both_buffers(kbdc, 10);
798 empty_both_buffers(kbdc, 10);
804 * Re-initialize the aux port and device. The aux port must be enabled
805 * and its interrupt must be disabled before calling this routine.
806 * The aux device will be disabled before returning.
807 * The keyboard controller must be locked via `kbdc_lock()' before
808 * calling this routine.
811 doinitialize(struct psm_softc *sc, mousemode_t *mode)
813 KBDC kbdc = sc->kbdc;
817 switch((i = test_aux_port(kbdc))) {
818 case 1: /* ignore these errors */
824 "psm%d: strange result for test aux port (%d).\n",
827 case 0: /* no error */
829 case -1: /* time out */
831 recover_from_error(kbdc);
832 if (sc->config & PSM_CONFIG_IGNPORTERROR)
834 log(LOG_ERR, "psm%d: the aux port is not functioning (%d).\n",
839 if (sc->config & PSM_CONFIG_NORESET) {
841 * Don't try to reset the pointing device. It may possibly
842 * be left in the unknown state, though...
846 * NOTE: some controllers appears to hang the `keyboard' when
847 * the aux port doesn't exist and `PSMC_RESET_DEV' is issued.
849 if (!reset_aux_dev(kbdc)) {
850 recover_from_error(kbdc);
851 log(LOG_ERR, "psm%d: failed to reset the aux device.\n",
858 * both the aux port and the aux device is functioning, see
859 * if the device can be enabled.
861 if (!enable_aux_dev(kbdc) || !disable_aux_dev(kbdc)) {
862 log(LOG_ERR, "psm%d: failed to enable the aux device.\n",
866 empty_both_buffers(kbdc, 10); /* remove stray data if any */
868 /* Re-enable the mouse. */
869 for (i = 0; vendortype[i].probefunc != NULL; ++i)
870 if (vendortype[i].model == sc->hw.model)
871 (*vendortype[i].probefunc)(sc->kbdc, NULL);
873 /* set mouse parameters */
874 if (mode != (mousemode_t *)NULL) {
876 mode->rate = set_mouse_sampling_rate(kbdc, mode->rate);
877 if (mode->resolution >= 0)
879 set_mouse_resolution(kbdc, mode->resolution);
880 set_mouse_scaling(kbdc, 1);
881 set_mouse_mode(kbdc);
884 /* Record sync on the next data packet we see. */
885 sc->flags |= PSM_NEED_SYNCBITS;
887 /* just check the status of the mouse */
888 if (get_mouse_status(kbdc, stat, 0, 3) < 3)
889 log(LOG_DEBUG, "psm%d: failed to get status (doinitialize).\n",
896 doopen(struct psm_softc *sc, int command_byte)
901 * FIXME: Synaptics TouchPad seems to go back to Relative Mode with
902 * no obvious reason. Thus we check the current mode and restore the
903 * Absolute Mode if it was cleared.
905 * The previous hack at the end of psmprobe() wasn't efficient when
906 * moused(8) was restarted.
908 * A Reset (FF) or Set Defaults (F6) command would clear the
909 * Absolute Mode bit. But a verbose boot or debug.psm.loglevel=5
910 * doesn't show any evidence of such a command.
912 if (sc->hw.model == MOUSE_MODEL_SYNAPTICS) {
913 mouse_ext_command(sc->kbdc, 1);
914 get_mouse_status(sc->kbdc, stat, 0, 3);
915 if ((SYNAPTICS_VERSION_GE(sc->synhw, 7, 5) ||
918 /* Set the mode byte -- request wmode where
920 if (sc->synhw.capExtended)
921 mouse_ext_command(sc->kbdc, 0xc1);
923 mouse_ext_command(sc->kbdc, 0xc0);
924 set_mouse_sampling_rate(sc->kbdc, 20);
925 VLOG(5, (LOG_DEBUG, "psm%d: Synaptis Absolute Mode "
926 "hopefully restored\n",
932 * A user may want to disable tap and drag gestures on a Synaptics
933 * TouchPad when it operates in Relative Mode.
935 if (sc->hw.model == MOUSE_MODEL_GENERIC) {
936 if (tap_enabled > 0) {
938 * Enable tap & drag gestures. We use a Mode Byte
939 * and clear the DisGest bit (see §2.5 of Synaptics
940 * TouchPad Interfacing Guide).
943 "psm%d: enable tap and drag gestures\n",
945 mouse_ext_command(sc->kbdc, 0x00);
946 set_mouse_sampling_rate(sc->kbdc, 20);
947 } else if (tap_enabled == 0) {
949 * Disable tap & drag gestures. We use a Mode Byte
950 * and set the DisGest bit (see §2.5 of Synaptics
951 * TouchPad Interfacing Guide).
954 "psm%d: disable tap and drag gestures\n",
956 mouse_ext_command(sc->kbdc, 0x04);
957 set_mouse_sampling_rate(sc->kbdc, 20);
961 /* enable the mouse device */
962 if (!enable_aux_dev(sc->kbdc)) {
963 /* MOUSE ERROR: failed to enable the mouse because:
964 * 1) the mouse is faulty,
965 * 2) the mouse has been removed(!?)
966 * In the latter case, the keyboard may have hung, and need
967 * recovery procedure...
969 recover_from_error(sc->kbdc);
971 /* FIXME: we could reset the mouse here and try to enable
972 * it again. But it will take long time and it's not a good
973 * idea to disable the keyboard that long...
975 if (!doinitialize(sc, &sc->mode) || !enable_aux_dev(sc->kbdc)) {
976 recover_from_error(sc->kbdc);
980 restore_controller(sc->kbdc, command_byte);
981 /* mark this device is no longer available */
982 sc->state &= ~PSM_VALID;
984 "psm%d: failed to enable the device (doopen).\n",
990 if (get_mouse_status(sc->kbdc, stat, 0, 3) < 3)
991 log(LOG_DEBUG, "psm%d: failed to get status (doopen).\n",
994 /* enable the aux port and interrupt */
995 if (!set_controller_command_byte(sc->kbdc,
996 kbdc_get_device_mask(sc->kbdc),
997 (command_byte & KBD_KBD_CONTROL_BITS) |
998 KBD_ENABLE_AUX_PORT | KBD_ENABLE_AUX_INT)) {
999 /* CONTROLLER ERROR */
1000 disable_aux_dev(sc->kbdc);
1001 restore_controller(sc->kbdc, command_byte);
1003 "psm%d: failed to enable the aux interrupt (doopen).\n",
1008 /* start the watchdog timer */
1009 sc->watchdog = FALSE;
1010 sc->callout = timeout(psmtimeout, (void *)(uintptr_t)sc, hz*2);
1016 reinitialize(struct psm_softc *sc, int doinit)
1022 /* don't let anybody mess with the aux device */
1023 if (!kbdc_lock(sc->kbdc, TRUE))
1027 /* block our watchdog timer */
1028 sc->watchdog = FALSE;
1029 untimeout(psmtimeout, (void *)(uintptr_t)sc, sc->callout);
1030 callout_handle_init(&sc->callout);
1032 /* save the current controller command byte */
1033 empty_both_buffers(sc->kbdc, 10);
1034 c = get_controller_command_byte(sc->kbdc);
1036 "psm%d: current command byte: %04x (reinitialize).\n",
1039 /* enable the aux port but disable the aux interrupt and the keyboard */
1040 if ((c == -1) || !set_controller_command_byte(sc->kbdc,
1041 kbdc_get_device_mask(sc->kbdc),
1042 KBD_DISABLE_KBD_PORT | KBD_DISABLE_KBD_INT |
1043 KBD_ENABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) {
1044 /* CONTROLLER ERROR */
1046 kbdc_lock(sc->kbdc, FALSE);
1048 "psm%d: unable to set the command byte (reinitialize).\n",
1053 /* flush any data */
1054 if (sc->state & PSM_VALID) {
1055 /* this may fail; but never mind... */
1056 disable_aux_dev(sc->kbdc);
1057 empty_aux_buffer(sc->kbdc, 10);
1062 memset(&sc->lastinputerr, 0, sizeof(sc->lastinputerr));
1064 /* try to detect the aux device; are you still there? */
1067 if (doinitialize(sc, &sc->mode)) {
1069 sc->state |= PSM_VALID;
1071 /* the device has gone! */
1072 restore_controller(sc->kbdc, c);
1073 sc->state &= ~PSM_VALID;
1075 "psm%d: the aux device has gone! (reinitialize).\n",
1082 /* restore the driver state */
1083 if ((sc->state & PSM_OPEN) && (err == 0)) {
1084 /* enable the aux device and the port again */
1085 err = doopen(sc, c);
1087 log(LOG_ERR, "psm%d: failed to enable the device "
1088 "(reinitialize).\n", sc->unit);
1090 /* restore the keyboard port and disable the aux port */
1091 if (!set_controller_command_byte(sc->kbdc,
1092 kbdc_get_device_mask(sc->kbdc),
1093 (c & KBD_KBD_CONTROL_BITS) |
1094 KBD_DISABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) {
1095 /* CONTROLLER ERROR */
1096 log(LOG_ERR, "psm%d: failed to disable the aux port "
1097 "(reinitialize).\n", sc->unit);
1102 kbdc_lock(sc->kbdc, FALSE);
1106 /* psm driver entry points */
1109 psmidentify(driver_t *driver, device_t parent)
1116 unit = device_get_unit(parent);
1118 /* always add at least one child */
1119 psm = BUS_ADD_CHILD(parent, KBDC_RID_AUX, driver->name, unit);
1123 irq = bus_get_resource_start(psm, SYS_RES_IRQ, KBDC_RID_AUX);
1128 * If the PS/2 mouse device has already been reported by ACPI or
1129 * PnP BIOS, obtain the IRQ resource from it.
1130 * (See psmcpnp_attach() below.)
1132 psmc = device_find_child(device_get_parent(parent),
1133 PSMCPNP_DRIVER_NAME, unit);
1136 irq = bus_get_resource_start(psmc, SYS_RES_IRQ, 0);
1139 bus_delete_resource(psmc, SYS_RES_IRQ, 0);
1140 bus_set_resource(psm, SYS_RES_IRQ, KBDC_RID_AUX, irq, 1);
1143 #define endprobe(v) do { \
1146 kbdc_set_device_mask(sc->kbdc, mask); \
1147 kbdc_lock(sc->kbdc, FALSE); \
1152 psmprobe(device_t dev)
1154 int unit = device_get_unit(dev);
1155 struct psm_softc *sc = device_get_softc(dev);
1166 /* see if IRQ is available */
1168 sc->intr = bus_alloc_resource_any(dev, SYS_RES_IRQ, &rid, RF_ACTIVE);
1169 if (sc->intr == NULL) {
1171 device_printf(dev, "unable to allocate IRQ\n");
1174 bus_release_resource(dev, SYS_RES_IRQ, rid, sc->intr);
1177 sc->kbdc = atkbdc_open(device_get_unit(device_get_parent(dev)));
1178 sc->config = device_get_flags(dev) & PSM_CONFIG_FLAGS;
1179 /* XXX: for backward compatibility */
1180 #if defined(PSM_HOOKRESUME) || defined(PSM_HOOKAPM)
1182 #ifdef PSM_RESETAFTERSUSPEND
1183 PSM_CONFIG_INITAFTERSUSPEND;
1185 PSM_CONFIG_HOOKRESUME;
1187 #endif /* PSM_HOOKRESUME | PSM_HOOKAPM */
1192 device_set_desc(dev, "PS/2 Mouse");
1194 if (!kbdc_lock(sc->kbdc, TRUE)) {
1195 printf("psm%d: unable to lock the controller.\n", unit);
1202 * NOTE: two bits in the command byte controls the operation of the
1203 * aux port (mouse port): the aux port disable bit (bit 5) and the aux
1204 * port interrupt (IRQ 12) enable bit (bit 2).
1207 /* discard anything left after the keyboard initialization */
1208 empty_both_buffers(sc->kbdc, 10);
1210 /* save the current command byte; it will be used later */
1211 mask = kbdc_get_device_mask(sc->kbdc) & ~KBD_AUX_CONTROL_BITS;
1212 command_byte = get_controller_command_byte(sc->kbdc);
1214 printf("psm%d: current command byte:%04x\n", unit,
1216 if (command_byte == -1) {
1217 /* CONTROLLER ERROR */
1218 printf("psm%d: unable to get the current command byte value.\n",
1224 * disable the keyboard port while probing the aux port, which must be
1225 * enabled during this routine
1227 if (!set_controller_command_byte(sc->kbdc,
1228 KBD_KBD_CONTROL_BITS | KBD_AUX_CONTROL_BITS,
1229 KBD_DISABLE_KBD_PORT | KBD_DISABLE_KBD_INT |
1230 KBD_ENABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) {
1232 * this is CONTROLLER ERROR; I don't know how to recover
1233 * from this error...
1235 restore_controller(sc->kbdc, command_byte);
1236 printf("psm%d: unable to set the command byte.\n", unit);
1239 write_controller_command(sc->kbdc, KBDC_ENABLE_AUX_PORT);
1242 * NOTE: `test_aux_port()' is designed to return with zero if the aux
1243 * port exists and is functioning. However, some controllers appears
1244 * to respond with zero even when the aux port doesn't exist. (It may
1245 * be that this is only the case when the controller DOES have the aux
1246 * port but the port is not wired on the motherboard.) The keyboard
1247 * controllers without the port, such as the original AT, are
1248 * supposed to return with an error code or simply time out. In any
1249 * case, we have to continue probing the port even when the controller
1252 * XXX: some controllers erroneously return the error code 1, 2 or 3
1253 * when it has a perfectly functional aux port. We have to ignore
1254 * this error code. Even if the controller HAS error with the aux
1255 * port, it will be detected later...
1256 * XXX: another incompatible controller returns PSM_ACK (0xfa)...
1258 switch ((i = test_aux_port(sc->kbdc))) {
1259 case 1: /* ignore these errors */
1264 printf("psm%d: strange result for test aux port "
1265 "(%d).\n", unit, i);
1267 case 0: /* no error */
1269 case -1: /* time out */
1270 default: /* error */
1271 recover_from_error(sc->kbdc);
1272 if (sc->config & PSM_CONFIG_IGNPORTERROR)
1274 restore_controller(sc->kbdc, command_byte);
1276 printf("psm%d: the aux port is not functioning (%d).\n",
1281 if (sc->config & PSM_CONFIG_NORESET) {
1283 * Don't try to reset the pointing device. It may possibly be
1284 * left in an unknown state, though...
1288 * NOTE: some controllers appears to hang the `keyboard' when
1289 * the aux port doesn't exist and `PSMC_RESET_DEV' is issued.
1291 * Attempt to reset the controller twice -- this helps
1292 * pierce through some KVM switches. The second reset
1295 if (!reset_aux_dev(sc->kbdc)) {
1296 recover_from_error(sc->kbdc);
1297 restore_controller(sc->kbdc, command_byte);
1299 printf("psm%d: failed to reset the aux "
1302 } else if (!reset_aux_dev(sc->kbdc)) {
1303 recover_from_error(sc->kbdc);
1305 printf("psm%d: failed to reset the aux device "
1311 * both the aux port and the aux device are functioning, see if the
1312 * device can be enabled. NOTE: when enabled, the device will start
1313 * sending data; we shall immediately disable the device once we know
1314 * the device can be enabled.
1316 if (!enable_aux_dev(sc->kbdc) || !disable_aux_dev(sc->kbdc)) {
1318 recover_from_error(sc->kbdc);
1319 restore_controller(sc->kbdc, command_byte);
1321 printf("psm%d: failed to enable the aux device.\n",
1326 /* save the default values after reset */
1327 if (get_mouse_status(sc->kbdc, stat, 0, 3) >= 3) {
1328 sc->dflt_mode.rate = sc->mode.rate = stat[2];
1329 sc->dflt_mode.resolution = sc->mode.resolution = stat[1];
1331 sc->dflt_mode.rate = sc->mode.rate = -1;
1332 sc->dflt_mode.resolution = sc->mode.resolution = -1;
1335 /* hardware information */
1336 sc->hw.iftype = MOUSE_IF_PS2;
1338 /* verify the device is a mouse */
1339 sc->hw.hwid = get_aux_id(sc->kbdc);
1340 if (!is_a_mouse(sc->hw.hwid)) {
1341 restore_controller(sc->kbdc, command_byte);
1343 printf("psm%d: unknown device type (%d).\n", unit,
1347 switch (sc->hw.hwid) {
1348 case PSM_BALLPOINT_ID:
1349 sc->hw.type = MOUSE_TRACKBALL;
1352 case PSM_INTELLI_ID:
1353 case PSM_EXPLORER_ID:
1354 case PSM_4DMOUSE_ID:
1356 sc->hw.type = MOUSE_MOUSE;
1359 sc->hw.type = MOUSE_UNKNOWN;
1363 if (sc->config & PSM_CONFIG_NOIDPROBE) {
1365 i = GENERIC_MOUSE_ENTRY;
1368 sc->hw.buttons = get_mouse_buttons(sc->kbdc);
1370 /* other parameters */
1371 for (i = 0; vendortype[i].probefunc != NULL; ++i)
1372 if ((*vendortype[i].probefunc)(sc->kbdc, sc)) {
1374 printf("psm%d: found %s\n", unit,
1375 model_name(vendortype[i].model));
1380 sc->hw.model = vendortype[i].model;
1382 sc->dflt_mode.level = PSM_LEVEL_BASE;
1383 sc->dflt_mode.packetsize = MOUSE_PS2_PACKETSIZE;
1384 sc->dflt_mode.accelfactor = (sc->config & PSM_CONFIG_ACCEL) >> 4;
1385 if (sc->config & PSM_CONFIG_NOCHECKSYNC)
1386 sc->dflt_mode.syncmask[0] = 0;
1388 sc->dflt_mode.syncmask[0] = vendortype[i].syncmask;
1389 if (sc->config & PSM_CONFIG_FORCETAP)
1390 sc->dflt_mode.syncmask[0] &= ~MOUSE_PS2_TAP;
1391 sc->dflt_mode.syncmask[1] = 0; /* syncbits */
1392 sc->mode = sc->dflt_mode;
1393 sc->mode.packetsize = vendortype[i].packetsize;
1395 /* set mouse parameters */
1398 * A version of Logitech FirstMouse+ won't report wheel movement,
1399 * if SET_DEFAULTS is sent... Don't use this command.
1400 * This fix was found by Takashi Nishida.
1402 i = send_aux_command(sc->kbdc, PSMC_SET_DEFAULTS);
1404 printf("psm%d: SET_DEFAULTS return code:%04x\n", unit, i);
1406 if (sc->config & PSM_CONFIG_RESOLUTION)
1407 sc->mode.resolution =
1408 set_mouse_resolution(sc->kbdc,
1409 (sc->config & PSM_CONFIG_RESOLUTION) - 1);
1410 else if (sc->mode.resolution >= 0)
1411 sc->mode.resolution =
1412 set_mouse_resolution(sc->kbdc, sc->dflt_mode.resolution);
1413 if (sc->mode.rate > 0)
1415 set_mouse_sampling_rate(sc->kbdc, sc->dflt_mode.rate);
1416 set_mouse_scaling(sc->kbdc, 1);
1418 /* Record sync on the next data packet we see. */
1419 sc->flags |= PSM_NEED_SYNCBITS;
1421 /* just check the status of the mouse */
1423 * NOTE: XXX there are some arcane controller/mouse combinations out
1424 * there, which hung the controller unless there is data transmission
1425 * after ACK from the mouse.
1427 if (get_mouse_status(sc->kbdc, stat, 0, 3) < 3)
1428 printf("psm%d: failed to get status.\n", unit);
1431 * When in its native mode, some mice operate with different
1432 * default parameters than in the PS/2 compatible mode.
1434 sc->dflt_mode.rate = sc->mode.rate = stat[2];
1435 sc->dflt_mode.resolution = sc->mode.resolution = stat[1];
1438 /* disable the aux port for now... */
1439 if (!set_controller_command_byte(sc->kbdc,
1440 KBD_KBD_CONTROL_BITS | KBD_AUX_CONTROL_BITS,
1441 (command_byte & KBD_KBD_CONTROL_BITS) |
1442 KBD_DISABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) {
1444 * this is CONTROLLER ERROR; I don't know the proper way to
1445 * recover from this error...
1447 restore_controller(sc->kbdc, command_byte);
1448 printf("psm%d: unable to set the command byte.\n", unit);
1453 kbdc_set_device_mask(sc->kbdc, mask | KBD_AUX_CONTROL_BITS);
1454 kbdc_lock(sc->kbdc, FALSE);
1459 psmattach(device_t dev)
1461 int unit = device_get_unit(dev);
1462 struct psm_softc *sc = device_get_softc(dev);
1466 /* Setup initial state */
1467 sc->state = PSM_VALID;
1468 callout_handle_init(&sc->callout);
1470 /* Setup our interrupt handler */
1472 sc->intr = bus_alloc_resource_any(dev, SYS_RES_IRQ, &rid, RF_ACTIVE);
1473 if (sc->intr == NULL)
1475 error = bus_setup_intr(dev, sc->intr, INTR_TYPE_TTY, NULL, psmintr, sc,
1478 bus_release_resource(dev, SYS_RES_IRQ, rid, sc->intr);
1483 sc->dev = make_dev(&psm_cdevsw, 0, 0, 0, 0666, "psm%d", unit);
1484 sc->dev->si_drv1 = sc;
1485 sc->bdev = make_dev(&psm_cdevsw, 0, 0, 0, 0666, "bpsm%d", unit);
1486 sc->bdev->si_drv1 = sc;
1488 /* Some touchpad devices need full reinitialization after suspend. */
1489 switch (sc->hw.model) {
1490 case MOUSE_MODEL_SYNAPTICS:
1491 case MOUSE_MODEL_GLIDEPOINT:
1492 case MOUSE_MODEL_VERSAPAD:
1493 sc->config |= PSM_CONFIG_INITAFTERSUSPEND;
1496 if (sc->synhw.infoMajor >= 4 || sc->tphw > 0)
1497 sc->config |= PSM_CONFIG_INITAFTERSUSPEND;
1502 printf("psm%d: model %s, device ID %d\n",
1503 unit, model_name(sc->hw.model), sc->hw.hwid & 0x00ff);
1505 printf("psm%d: model %s, device ID %d-%02x, %d buttons\n",
1506 unit, model_name(sc->hw.model), sc->hw.hwid & 0x00ff,
1507 sc->hw.hwid >> 8, sc->hw.buttons);
1508 printf("psm%d: config:%08x, flags:%08x, packet size:%d\n",
1509 unit, sc->config, sc->flags, sc->mode.packetsize);
1510 printf("psm%d: syncmask:%02x, syncbits:%02x\n",
1511 unit, sc->mode.syncmask[0], sc->mode.syncmask[1]);
1521 psmdetach(device_t dev)
1523 struct psm_softc *sc;
1526 sc = device_get_softc(dev);
1527 if (sc->state & PSM_OPEN)
1531 bus_teardown_intr(dev, sc->intr, sc->ih);
1532 bus_release_resource(dev, SYS_RES_IRQ, rid, sc->intr);
1534 destroy_dev(sc->dev);
1535 destroy_dev(sc->bdev);
1541 psmopen(struct cdev *dev, int flag, int fmt, struct thread *td)
1543 struct psm_softc *sc;
1548 /* Get device data */
1550 if ((sc == NULL) || (sc->state & PSM_VALID) == 0) {
1551 /* the device is no longer valid/functioning */
1555 /* Disallow multiple opens */
1556 if (sc->state & PSM_OPEN)
1559 device_busy(devclass_get_device(psm_devclass, sc->unit));
1561 /* Initialize state */
1562 sc->mode.level = sc->dflt_mode.level;
1563 sc->mode.protocol = sc->dflt_mode.protocol;
1564 sc->watchdog = FALSE;
1567 /* flush the event queue */
1568 sc->queue.count = 0;
1571 sc->status.flags = 0;
1572 sc->status.button = 0;
1573 sc->status.obutton = 0;
1578 sc->pqueue_start = 0;
1581 /* empty input buffer */
1586 /* don't let timeout routines in the keyboard driver to poll the kbdc */
1587 if (!kbdc_lock(sc->kbdc, TRUE))
1590 /* save the current controller command byte */
1592 command_byte = get_controller_command_byte(sc->kbdc);
1594 /* enable the aux port and temporalily disable the keyboard */
1595 if (command_byte == -1 || !set_controller_command_byte(sc->kbdc,
1596 kbdc_get_device_mask(sc->kbdc),
1597 KBD_DISABLE_KBD_PORT | KBD_DISABLE_KBD_INT |
1598 KBD_ENABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) {
1599 /* CONTROLLER ERROR; do you know how to get out of this? */
1600 kbdc_lock(sc->kbdc, FALSE);
1603 "psm%d: unable to set the command byte (psmopen).\n",
1608 * Now that the keyboard controller is told not to generate
1609 * the keyboard and mouse interrupts, call `splx()' to allow
1610 * the other tty interrupts. The clock interrupt may also occur,
1611 * but timeout routines will be blocked by the poll flag set
1616 /* enable the mouse device */
1617 err = doopen(sc, command_byte);
1621 sc->state |= PSM_OPEN;
1622 kbdc_lock(sc->kbdc, FALSE);
1627 psmclose(struct cdev *dev, int flag, int fmt, struct thread *td)
1629 struct psm_softc *sc = dev->si_drv1;
1634 /* don't let timeout routines in the keyboard driver to poll the kbdc */
1635 if (!kbdc_lock(sc->kbdc, TRUE))
1638 /* save the current controller command byte */
1640 command_byte = get_controller_command_byte(sc->kbdc);
1641 if (command_byte == -1) {
1642 kbdc_lock(sc->kbdc, FALSE);
1647 /* disable the aux interrupt and temporalily disable the keyboard */
1648 if (!set_controller_command_byte(sc->kbdc,
1649 kbdc_get_device_mask(sc->kbdc),
1650 KBD_DISABLE_KBD_PORT | KBD_DISABLE_KBD_INT |
1651 KBD_ENABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) {
1653 "psm%d: failed to disable the aux int (psmclose).\n",
1655 /* CONTROLLER ERROR;
1656 * NOTE: we shall force our way through. Because the only
1657 * ill effect we shall see is that we may not be able
1658 * to read ACK from the mouse, and it doesn't matter much
1659 * so long as the mouse will accept the DISABLE command.
1664 /* stop the watchdog timer */
1665 untimeout(psmtimeout, (void *)(uintptr_t)sc, sc->callout);
1666 callout_handle_init(&sc->callout);
1668 /* remove anything left in the output buffer */
1669 empty_aux_buffer(sc->kbdc, 10);
1671 /* disable the aux device, port and interrupt */
1672 if (sc->state & PSM_VALID) {
1673 if (!disable_aux_dev(sc->kbdc)) {
1675 * NOTE: we don't return (error) and continue,
1676 * pretending we have successfully disabled the device.
1677 * It's OK because the interrupt routine will discard
1678 * any data from the mouse hereafter.
1681 "psm%d: failed to disable the device (psmclose).\n",
1685 if (get_mouse_status(sc->kbdc, stat, 0, 3) < 3)
1687 "psm%d: failed to get status (psmclose).\n",
1691 if (!set_controller_command_byte(sc->kbdc,
1692 kbdc_get_device_mask(sc->kbdc),
1693 (command_byte & KBD_KBD_CONTROL_BITS) |
1694 KBD_DISABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) {
1697 * we shall ignore this error; see the above comment.
1700 "psm%d: failed to disable the aux port (psmclose).\n",
1704 /* remove anything left in the output buffer */
1705 empty_aux_buffer(sc->kbdc, 10);
1707 /* clean up and sigio requests */
1708 if (sc->async != NULL) {
1709 funsetown(&sc->async);
1713 /* close is almost always successful */
1714 sc->state &= ~PSM_OPEN;
1715 kbdc_lock(sc->kbdc, FALSE);
1716 device_unbusy(devclass_get_device(psm_devclass, sc->unit));
1721 tame_mouse(struct psm_softc *sc, packetbuf_t *pb, mousestatus_t *status,
1724 static u_char butmapps2[8] = {
1726 MOUSE_PS2_BUTTON1DOWN,
1727 MOUSE_PS2_BUTTON2DOWN,
1728 MOUSE_PS2_BUTTON1DOWN | MOUSE_PS2_BUTTON2DOWN,
1729 MOUSE_PS2_BUTTON3DOWN,
1730 MOUSE_PS2_BUTTON1DOWN | MOUSE_PS2_BUTTON3DOWN,
1731 MOUSE_PS2_BUTTON2DOWN | MOUSE_PS2_BUTTON3DOWN,
1732 MOUSE_PS2_BUTTON1DOWN | MOUSE_PS2_BUTTON2DOWN |
1733 MOUSE_PS2_BUTTON3DOWN,
1735 static u_char butmapmsc[8] = {
1736 MOUSE_MSC_BUTTON1UP | MOUSE_MSC_BUTTON2UP |
1737 MOUSE_MSC_BUTTON3UP,
1738 MOUSE_MSC_BUTTON2UP | MOUSE_MSC_BUTTON3UP,
1739 MOUSE_MSC_BUTTON1UP | MOUSE_MSC_BUTTON3UP,
1740 MOUSE_MSC_BUTTON3UP,
1741 MOUSE_MSC_BUTTON1UP | MOUSE_MSC_BUTTON2UP,
1742 MOUSE_MSC_BUTTON2UP,
1743 MOUSE_MSC_BUTTON1UP,
1749 if (sc->mode.level == PSM_LEVEL_BASE) {
1750 mapped = status->button & ~MOUSE_BUTTON4DOWN;
1751 if (status->button & MOUSE_BUTTON4DOWN)
1752 mapped |= MOUSE_BUTTON1DOWN;
1753 status->button = mapped;
1754 buf[0] = MOUSE_PS2_SYNC | butmapps2[mapped & MOUSE_STDBUTTONS];
1755 i = imax(imin(status->dx, 255), -256);
1757 buf[0] |= MOUSE_PS2_XNEG;
1759 i = imax(imin(status->dy, 255), -256);
1761 buf[0] |= MOUSE_PS2_YNEG;
1763 return (MOUSE_PS2_PACKETSIZE);
1764 } else if (sc->mode.level == PSM_LEVEL_STANDARD) {
1765 buf[0] = MOUSE_MSC_SYNC |
1766 butmapmsc[status->button & MOUSE_STDBUTTONS];
1767 i = imax(imin(status->dx, 255), -256);
1769 buf[3] = i - buf[1];
1770 i = imax(imin(status->dy, 255), -256);
1772 buf[4] = i - buf[2];
1773 i = imax(imin(status->dz, 127), -128);
1774 buf[5] = (i >> 1) & 0x7f;
1775 buf[6] = (i - (i >> 1)) & 0x7f;
1776 buf[7] = (~status->button >> 3) & 0x7f;
1777 return (MOUSE_SYS_PACKETSIZE);
1779 return (pb->inputbytes);
1783 psmread(struct cdev *dev, struct uio *uio, int flag)
1785 struct psm_softc *sc = dev->si_drv1;
1786 u_char buf[PSM_SMALLBUFSIZE];
1791 if ((sc->state & PSM_VALID) == 0)
1794 /* block until mouse activity occured */
1796 while (sc->queue.count <= 0) {
1797 if (dev != sc->bdev) {
1799 return (EWOULDBLOCK);
1801 sc->state |= PSM_ASLP;
1802 error = tsleep(sc, PZERO | PCATCH, "psmrea", 0);
1803 sc->state &= ~PSM_ASLP;
1807 } else if ((sc->state & PSM_VALID) == 0) {
1808 /* the device disappeared! */
1815 /* copy data to the user land */
1816 while ((sc->queue.count > 0) && (uio->uio_resid > 0)) {
1818 l = imin(sc->queue.count, uio->uio_resid);
1819 if (l > sizeof(buf))
1821 if (l > sizeof(sc->queue.buf) - sc->queue.head) {
1822 bcopy(&sc->queue.buf[sc->queue.head], &buf[0],
1823 sizeof(sc->queue.buf) - sc->queue.head);
1824 bcopy(&sc->queue.buf[0],
1825 &buf[sizeof(sc->queue.buf) - sc->queue.head],
1826 l - (sizeof(sc->queue.buf) - sc->queue.head));
1828 bcopy(&sc->queue.buf[sc->queue.head], &buf[0], l);
1829 sc->queue.count -= l;
1830 sc->queue.head = (sc->queue.head + l) % sizeof(sc->queue.buf);
1832 error = uiomove(buf, l, uio);
1841 block_mouse_data(struct psm_softc *sc, int *c)
1845 if (!kbdc_lock(sc->kbdc, TRUE))
1849 *c = get_controller_command_byte(sc->kbdc);
1850 if ((*c == -1) || !set_controller_command_byte(sc->kbdc,
1851 kbdc_get_device_mask(sc->kbdc),
1852 KBD_DISABLE_KBD_PORT | KBD_DISABLE_KBD_INT |
1853 KBD_ENABLE_AUX_PORT | KBD_DISABLE_AUX_INT)) {
1854 /* this is CONTROLLER ERROR */
1856 kbdc_lock(sc->kbdc, FALSE);
1861 * The device may be in the middle of status data transmission.
1862 * The transmission will be interrupted, thus, incomplete status
1863 * data must be discarded. Although the aux interrupt is disabled
1864 * at the keyboard controller level, at most one aux interrupt
1865 * may have already been pending and a data byte is in the
1866 * output buffer; throw it away. Note that the second argument
1867 * to `empty_aux_buffer()' is zero, so that the call will just
1868 * flush the internal queue.
1869 * `psmintr()' will be invoked after `splx()' if an interrupt is
1870 * pending; it will see no data and returns immediately.
1872 empty_aux_buffer(sc->kbdc, 0); /* flush the queue */
1873 read_aux_data_no_wait(sc->kbdc); /* throw away data if any */
1881 dropqueue(struct psm_softc *sc)
1884 sc->queue.count = 0;
1887 if ((sc->state & PSM_SOFTARMED) != 0) {
1888 sc->state &= ~PSM_SOFTARMED;
1889 untimeout(psmsoftintr, (void *)(uintptr_t)sc, sc->softcallout);
1891 sc->pqueue_start = sc->pqueue_end;
1895 flushpackets(struct psm_softc *sc)
1899 bzero(&sc->pqueue, sizeof(sc->pqueue));
1903 unblock_mouse_data(struct psm_softc *sc, int c)
1908 * We may have seen a part of status data during `set_mouse_XXX()'.
1909 * they have been queued; flush it.
1911 empty_aux_buffer(sc->kbdc, 0);
1913 /* restore ports and interrupt */
1914 if (!set_controller_command_byte(sc->kbdc,
1915 kbdc_get_device_mask(sc->kbdc),
1916 c & (KBD_KBD_CONTROL_BITS | KBD_AUX_CONTROL_BITS))) {
1918 * CONTROLLER ERROR; this is serious, we may have
1919 * been left with the inaccessible keyboard and
1920 * the disabled mouse interrupt.
1925 kbdc_lock(sc->kbdc, FALSE);
1930 psmwrite(struct cdev *dev, struct uio *uio, int flag)
1932 struct psm_softc *sc = dev->si_drv1;
1933 u_char buf[PSM_SMALLBUFSIZE];
1934 int error = 0, i, l;
1936 if ((sc->state & PSM_VALID) == 0)
1939 if (sc->mode.level < PSM_LEVEL_NATIVE)
1942 /* copy data from the user land */
1943 while (uio->uio_resid > 0) {
1944 l = imin(PSM_SMALLBUFSIZE, uio->uio_resid);
1945 error = uiomove(buf, l, uio);
1948 for (i = 0; i < l; i++) {
1949 VLOG(4, (LOG_DEBUG, "psm: cmd 0x%x\n", buf[i]));
1950 if (!write_aux_command(sc->kbdc, buf[i])) {
1952 "psm: cmd 0x%x failed.\n", buf[i]));
1953 return (reinitialize(sc, FALSE));
1962 psmioctl(struct cdev *dev, u_long cmd, caddr_t addr, int flag,
1965 struct psm_softc *sc = dev->si_drv1;
1967 mousestatus_t status;
1968 #if (defined(MOUSE_GETVARS))
1977 /* Perform IOCTL command */
1980 case OLD_MOUSE_GETHWINFO:
1982 ((old_mousehw_t *)addr)->buttons = sc->hw.buttons;
1983 ((old_mousehw_t *)addr)->iftype = sc->hw.iftype;
1984 ((old_mousehw_t *)addr)->type = sc->hw.type;
1985 ((old_mousehw_t *)addr)->hwid = sc->hw.hwid & 0x00ff;
1989 case MOUSE_GETHWINFO:
1991 *(mousehw_t *)addr = sc->hw;
1992 if (sc->mode.level == PSM_LEVEL_BASE)
1993 ((mousehw_t *)addr)->model = MOUSE_MODEL_GENERIC;
1997 case MOUSE_SYN_GETHWINFO:
1999 if (sc->synhw.infoMajor >= 4)
2000 *(synapticshw_t *)addr = sc->synhw;
2006 case OLD_MOUSE_GETMODE:
2008 switch (sc->mode.level) {
2009 case PSM_LEVEL_BASE:
2010 ((old_mousemode_t *)addr)->protocol = MOUSE_PROTO_PS2;
2012 case PSM_LEVEL_STANDARD:
2013 ((old_mousemode_t *)addr)->protocol =
2014 MOUSE_PROTO_SYSMOUSE;
2016 case PSM_LEVEL_NATIVE:
2017 ((old_mousemode_t *)addr)->protocol = MOUSE_PROTO_PS2;
2020 ((old_mousemode_t *)addr)->rate = sc->mode.rate;
2021 ((old_mousemode_t *)addr)->resolution = sc->mode.resolution;
2022 ((old_mousemode_t *)addr)->accelfactor = sc->mode.accelfactor;
2028 *(mousemode_t *)addr = sc->mode;
2029 if ((sc->flags & PSM_NEED_SYNCBITS) != 0) {
2030 ((mousemode_t *)addr)->syncmask[0] = 0;
2031 ((mousemode_t *)addr)->syncmask[1] = 0;
2033 ((mousemode_t *)addr)->resolution =
2034 MOUSE_RES_LOW - sc->mode.resolution;
2035 switch (sc->mode.level) {
2036 case PSM_LEVEL_BASE:
2037 ((mousemode_t *)addr)->protocol = MOUSE_PROTO_PS2;
2038 ((mousemode_t *)addr)->packetsize =
2039 MOUSE_PS2_PACKETSIZE;
2041 case PSM_LEVEL_STANDARD:
2042 ((mousemode_t *)addr)->protocol = MOUSE_PROTO_SYSMOUSE;
2043 ((mousemode_t *)addr)->packetsize =
2044 MOUSE_SYS_PACKETSIZE;
2045 ((mousemode_t *)addr)->syncmask[0] = MOUSE_SYS_SYNCMASK;
2046 ((mousemode_t *)addr)->syncmask[1] = MOUSE_SYS_SYNC;
2048 case PSM_LEVEL_NATIVE:
2049 /* FIXME: this isn't quite correct... XXX */
2050 ((mousemode_t *)addr)->protocol = MOUSE_PROTO_PS2;
2056 case OLD_MOUSE_SETMODE:
2058 if (cmd == OLD_MOUSE_SETMODE) {
2059 mode.rate = ((old_mousemode_t *)addr)->rate;
2061 * resolution old I/F new I/F
2068 if (((old_mousemode_t *)addr)->resolution > 0)
2070 -((old_mousemode_t *)addr)->resolution - 1;
2072 mode.resolution = 0;
2074 ((old_mousemode_t *)addr)->accelfactor;
2077 mode = *(mousemode_t *)addr;
2079 /* adjust and validate parameters. */
2080 if (mode.rate > UCHAR_MAX)
2083 mode.rate = sc->dflt_mode.rate;
2084 else if (mode.rate == -1)
2085 /* don't change the current setting */
2087 else if (mode.rate < 0)
2089 if (mode.resolution >= UCHAR_MAX)
2091 if (mode.resolution >= 200)
2092 mode.resolution = MOUSE_RES_HIGH;
2093 else if (mode.resolution >= 100)
2094 mode.resolution = MOUSE_RES_MEDIUMHIGH;
2095 else if (mode.resolution >= 50)
2096 mode.resolution = MOUSE_RES_MEDIUMLOW;
2097 else if (mode.resolution > 0)
2098 mode.resolution = MOUSE_RES_LOW;
2099 if (mode.resolution == MOUSE_RES_DEFAULT)
2100 mode.resolution = sc->dflt_mode.resolution;
2101 else if (mode.resolution == -1)
2102 /* don't change the current setting */
2104 else if (mode.resolution < 0) /* MOUSE_RES_LOW/MEDIUM/HIGH */
2105 mode.resolution = MOUSE_RES_LOW - mode.resolution;
2106 if (mode.level == -1)
2107 /* don't change the current setting */
2108 mode.level = sc->mode.level;
2109 else if ((mode.level < PSM_LEVEL_MIN) ||
2110 (mode.level > PSM_LEVEL_MAX))
2112 if (mode.accelfactor == -1)
2113 /* don't change the current setting */
2114 mode.accelfactor = sc->mode.accelfactor;
2115 else if (mode.accelfactor < 0)
2118 /* don't allow anybody to poll the keyboard controller */
2119 error = block_mouse_data(sc, &command_byte);
2123 /* set mouse parameters */
2125 mode.rate = set_mouse_sampling_rate(sc->kbdc,
2127 if (mode.resolution >= 0)
2129 set_mouse_resolution(sc->kbdc, mode.resolution);
2130 set_mouse_scaling(sc->kbdc, 1);
2131 get_mouse_status(sc->kbdc, stat, 0, 3);
2134 sc->mode.rate = mode.rate;
2135 sc->mode.resolution = mode.resolution;
2136 sc->mode.accelfactor = mode.accelfactor;
2137 sc->mode.level = mode.level;
2140 unblock_mouse_data(sc, command_byte);
2143 case MOUSE_GETLEVEL:
2144 *(int *)addr = sc->mode.level;
2147 case MOUSE_SETLEVEL:
2148 if ((*(int *)addr < PSM_LEVEL_MIN) ||
2149 (*(int *)addr > PSM_LEVEL_MAX))
2151 sc->mode.level = *(int *)addr;
2154 case MOUSE_GETSTATUS:
2156 status = sc->status;
2157 sc->status.flags = 0;
2158 sc->status.obutton = sc->status.button;
2159 sc->status.button = 0;
2164 *(mousestatus_t *)addr = status;
2167 #if (defined(MOUSE_GETVARS))
2169 var = (mousevar_t *)addr;
2170 bzero(var, sizeof(*var));
2172 var->var[0] = MOUSE_VARS_PS2_SIG;
2173 var->var[1] = sc->config;
2174 var->var[2] = sc->flags;
2180 #endif /* MOUSE_GETVARS */
2182 case MOUSE_READSTATE:
2183 case MOUSE_READDATA:
2184 data = (mousedata_t *)addr;
2185 if (data->len > sizeof(data->buf)/sizeof(data->buf[0]))
2188 error = block_mouse_data(sc, &command_byte);
2191 if ((data->len = get_mouse_status(sc->kbdc, data->buf,
2192 (cmd == MOUSE_READDATA) ? 1 : 0, data->len)) <= 0)
2194 unblock_mouse_data(sc, command_byte);
2197 #if (defined(MOUSE_SETRESOLUTION))
2198 case MOUSE_SETRESOLUTION:
2199 mode.resolution = *(int *)addr;
2200 if (mode.resolution >= UCHAR_MAX)
2202 else if (mode.resolution >= 200)
2203 mode.resolution = MOUSE_RES_HIGH;
2204 else if (mode.resolution >= 100)
2205 mode.resolution = MOUSE_RES_MEDIUMHIGH;
2206 else if (mode.resolution >= 50)
2207 mode.resolution = MOUSE_RES_MEDIUMLOW;
2208 else if (mode.resolution > 0)
2209 mode.resolution = MOUSE_RES_LOW;
2210 if (mode.resolution == MOUSE_RES_DEFAULT)
2211 mode.resolution = sc->dflt_mode.resolution;
2212 else if (mode.resolution == -1)
2213 mode.resolution = sc->mode.resolution;
2214 else if (mode.resolution < 0) /* MOUSE_RES_LOW/MEDIUM/HIGH */
2215 mode.resolution = MOUSE_RES_LOW - mode.resolution;
2217 error = block_mouse_data(sc, &command_byte);
2220 sc->mode.resolution =
2221 set_mouse_resolution(sc->kbdc, mode.resolution);
2222 if (sc->mode.resolution != mode.resolution)
2224 unblock_mouse_data(sc, command_byte);
2226 #endif /* MOUSE_SETRESOLUTION */
2228 #if (defined(MOUSE_SETRATE))
2230 mode.rate = *(int *)addr;
2231 if (mode.rate > UCHAR_MAX)
2234 mode.rate = sc->dflt_mode.rate;
2235 else if (mode.rate < 0)
2236 mode.rate = sc->mode.rate;
2238 error = block_mouse_data(sc, &command_byte);
2241 sc->mode.rate = set_mouse_sampling_rate(sc->kbdc, mode.rate);
2242 if (sc->mode.rate != mode.rate)
2244 unblock_mouse_data(sc, command_byte);
2246 #endif /* MOUSE_SETRATE */
2248 #if (defined(MOUSE_SETSCALING))
2249 case MOUSE_SETSCALING:
2250 if ((*(int *)addr <= 0) || (*(int *)addr > 2))
2253 error = block_mouse_data(sc, &command_byte);
2256 if (!set_mouse_scaling(sc->kbdc, *(int *)addr))
2258 unblock_mouse_data(sc, command_byte);
2260 #endif /* MOUSE_SETSCALING */
2262 #if (defined(MOUSE_GETHWID))
2264 error = block_mouse_data(sc, &command_byte);
2267 sc->hw.hwid &= ~0x00ff;
2268 sc->hw.hwid |= get_aux_id(sc->kbdc);
2269 *(int *)addr = sc->hw.hwid & 0x00ff;
2270 unblock_mouse_data(sc, command_byte);
2272 #endif /* MOUSE_GETHWID */
2278 error = fsetown(*(int *)addr, &sc->async);
2281 *(int *) addr = fgetown(&sc->async);
2291 psmtimeout(void *arg)
2293 struct psm_softc *sc;
2296 sc = (struct psm_softc *)arg;
2298 if (sc->watchdog && kbdc_lock(sc->kbdc, TRUE)) {
2299 VLOG(4, (LOG_DEBUG, "psm%d: lost interrupt?\n", sc->unit));
2301 kbdc_lock(sc->kbdc, FALSE);
2303 sc->watchdog = TRUE;
2305 sc->callout = timeout(psmtimeout, (void *)(uintptr_t)sc, hz);
2308 /* Add all sysctls under the debug.psm and hw.psm nodes */
2309 static SYSCTL_NODE(_debug, OID_AUTO, psm, CTLFLAG_RD, 0, "ps/2 mouse");
2310 static SYSCTL_NODE(_hw, OID_AUTO, psm, CTLFLAG_RD, 0, "ps/2 mouse");
2312 SYSCTL_INT(_debug_psm, OID_AUTO, loglevel, CTLFLAG_RW, &verbose, 0,
2315 static int psmhz = 20;
2316 SYSCTL_INT(_debug_psm, OID_AUTO, hz, CTLFLAG_RW, &psmhz, 0,
2317 "Frequency of the softcallout (in hz)");
2318 static int psmerrsecs = 2;
2319 SYSCTL_INT(_debug_psm, OID_AUTO, errsecs, CTLFLAG_RW, &psmerrsecs, 0,
2320 "Number of seconds during which packets will dropped after a sync error");
2321 static int psmerrusecs = 0;
2322 SYSCTL_INT(_debug_psm, OID_AUTO, errusecs, CTLFLAG_RW, &psmerrusecs, 0,
2323 "Microseconds to add to psmerrsecs");
2324 static int psmsecs = 0;
2325 SYSCTL_INT(_debug_psm, OID_AUTO, secs, CTLFLAG_RW, &psmsecs, 0,
2326 "Max number of seconds between soft interrupts");
2327 static int psmusecs = 500000;
2328 SYSCTL_INT(_debug_psm, OID_AUTO, usecs, CTLFLAG_RW, &psmusecs, 0,
2329 "Microseconds to add to psmsecs");
2330 static int pkterrthresh = 2;
2331 SYSCTL_INT(_debug_psm, OID_AUTO, pkterrthresh, CTLFLAG_RW, &pkterrthresh, 0,
2332 "Number of error packets allowed before reinitializing the mouse");
2334 SYSCTL_INT(_hw_psm, OID_AUTO, tap_enabled, CTLFLAG_RW, &tap_enabled, 0,
2335 "Enable tap and drag gestures");
2336 static int tap_threshold = PSM_TAP_THRESHOLD;
2337 SYSCTL_INT(_hw_psm, OID_AUTO, tap_threshold, CTLFLAG_RW, &tap_threshold, 0,
2338 "Button tap threshold");
2339 static int tap_timeout = PSM_TAP_TIMEOUT;
2340 SYSCTL_INT(_hw_psm, OID_AUTO, tap_timeout, CTLFLAG_RW, &tap_timeout, 0,
2341 "Tap timeout for touchpads");
2346 struct psm_softc *sc = arg;
2352 /* read until there is nothing to read */
2353 while((c = read_aux_data_no_wait(sc->kbdc)) != -1) {
2354 pb = &sc->pqueue[sc->pqueue_end];
2356 /* discard the byte if the device is not open */
2357 if ((sc->state & PSM_OPEN) == 0)
2360 getmicrouptime(&now);
2361 if ((pb->inputbytes > 0) &&
2362 timevalcmp(&now, &sc->inputtimeout, >)) {
2363 VLOG(3, (LOG_DEBUG, "psmintr: delay too long; "
2364 "resetting byte count\n"));
2369 sc->inputtimeout.tv_sec = PSM_INPUT_TIMEOUT / 1000000;
2370 sc->inputtimeout.tv_usec = PSM_INPUT_TIMEOUT % 1000000;
2371 timevaladd(&sc->inputtimeout, &now);
2373 pb->ipacket[pb->inputbytes++] = c;
2375 if (sc->mode.level == PSM_LEVEL_NATIVE) {
2376 VLOG(4, (LOG_DEBUG, "psmintr: %02x\n", pb->ipacket[0]));
2381 if (pb->inputbytes < sc->mode.packetsize)
2385 "psmintr: %02x %02x %02x %02x %02x %02x\n",
2386 pb->ipacket[0], pb->ipacket[1], pb->ipacket[2],
2387 pb->ipacket[3], pb->ipacket[4], pb->ipacket[5]));
2392 if ((sc->flags & PSM_NEED_SYNCBITS) != 0) {
2393 sc->mode.syncmask[1] = (c & sc->mode.syncmask[0]);
2394 sc->flags &= ~PSM_NEED_SYNCBITS;
2396 "psmintr: Sync bytes now %04x,%04x\n",
2397 sc->mode.syncmask[0], sc->mode.syncmask[0]));
2398 } else if ((c & sc->mode.syncmask[0]) != sc->mode.syncmask[1]) {
2399 VLOG(3, (LOG_DEBUG, "psmintr: out of sync "
2400 "(%04x != %04x) %d cmds since last error.\n",
2401 c & sc->mode.syncmask[0], sc->mode.syncmask[1],
2402 sc->cmdcount - sc->lasterr));
2403 sc->lasterr = sc->cmdcount;
2405 * The sync byte test is a weak measure of packet
2406 * validity. Conservatively discard any input yet
2407 * to be seen by userland when we detect a sync
2408 * error since there is a good chance some of
2409 * the queued packets have undetected errors.
2412 if (sc->syncerrors == 0)
2415 sc->lastinputerr = now;
2416 if (sc->syncerrors >= sc->mode.packetsize * 2 ||
2417 sc->pkterrors >= pkterrthresh) {
2419 * If we've failed to find a single sync byte
2420 * in 2 packets worth of data, or we've seen
2421 * persistent packet errors during the
2422 * validation period, reinitialize the mouse
2423 * in hopes of returning it to the expected
2427 "psmintr: reset the mouse.\n"));
2428 reinitialize(sc, TRUE);
2429 } else if (sc->syncerrors == sc->mode.packetsize) {
2431 * Try a soft reset after searching for a sync
2432 * byte through a packet length of bytes.
2435 "psmintr: re-enable the mouse.\n"));
2437 disable_aux_dev(sc->kbdc);
2438 enable_aux_dev(sc->kbdc);
2441 "psmintr: discard a byte (%d)\n",
2444 bcopy(&pb->ipacket[1], &pb->ipacket[0],
2451 * We have what appears to be a valid packet.
2452 * Reset the error counters.
2457 * Drop even good packets if they occur within a timeout
2458 * period of a sync error. This allows the detection of
2459 * a change in the mouse's packet mode without exposing
2460 * erratic mouse behavior to the user. Some KVMs forget
2461 * enhanced mouse modes during switch events.
2463 if (!timeelapsed(&sc->lastinputerr, psmerrsecs, psmerrusecs,
2470 * Now that we're out of the validation period, reset
2471 * the packet error count.
2477 if (++sc->pqueue_end >= PSM_PACKETQUEUE)
2480 * If we've filled the queue then call the softintr ourselves,
2481 * otherwise schedule the interrupt for later.
2483 if (!timeelapsed(&sc->lastsoftintr, psmsecs, psmusecs, &now) ||
2484 (sc->pqueue_end == sc->pqueue_start)) {
2485 if ((sc->state & PSM_SOFTARMED) != 0) {
2486 sc->state &= ~PSM_SOFTARMED;
2487 untimeout(psmsoftintr, arg, sc->softcallout);
2490 } else if ((sc->state & PSM_SOFTARMED) == 0) {
2491 sc->state |= PSM_SOFTARMED;
2492 sc->softcallout = timeout(psmsoftintr, arg,
2493 psmhz < 1 ? 1 : (hz/psmhz));
2499 proc_mmanplus(struct psm_softc *sc, packetbuf_t *pb, mousestatus_t *ms,
2500 int *x, int *y, int *z)
2504 * PS2++ protocol packet
2506 * b7 b6 b5 b4 b3 b2 b1 b0
2507 * byte 1: * 1 p3 p2 1 * * *
2508 * byte 2: c1 c2 p1 p0 d1 d0 1 0
2510 * p3-p0: packet type
2511 * c1, c2: c1 & c2 == 1, if p2 == 0
2512 * c1 & c2 == 0, if p2 == 1
2514 * packet type: 0 (device type)
2515 * See comments in enable_mmanplus() below.
2517 * packet type: 1 (wheel data)
2519 * b7 b6 b5 b4 b3 b2 b1 b0
2520 * byte 3: h * B5 B4 s d2 d1 d0
2522 * h: 1, if horizontal roller data
2523 * 0, if vertical roller data
2524 * B4, B5: button 4 and 5
2526 * d2-d0: roller data
2528 * packet type: 2 (reserved)
2530 if (((pb->ipacket[0] & MOUSE_PS2PLUS_SYNCMASK) == MOUSE_PS2PLUS_SYNC) &&
2531 (abs(*x) > 191) && MOUSE_PS2PLUS_CHECKBITS(pb->ipacket)) {
2533 * the extended data packet encodes button
2536 switch (MOUSE_PS2PLUS_PACKET_TYPE(pb->ipacket)) {
2538 /* wheel data packet */
2540 if (pb->ipacket[2] & 0x80) {
2541 /* XXX horizontal roller count - ignore it */
2544 /* vertical roller count */
2545 *z = (pb->ipacket[2] & MOUSE_PS2PLUS_ZNEG) ?
2546 (pb->ipacket[2] & 0x0f) - 16 :
2547 (pb->ipacket[2] & 0x0f);
2549 ms->button |= (pb->ipacket[2] &
2550 MOUSE_PS2PLUS_BUTTON4DOWN) ?
2551 MOUSE_BUTTON4DOWN : 0;
2552 ms->button |= (pb->ipacket[2] &
2553 MOUSE_PS2PLUS_BUTTON5DOWN) ?
2554 MOUSE_BUTTON5DOWN : 0;
2558 * this packet type is reserved by
2562 * IBM ScrollPoint Mouse uses this
2563 * packet type to encode both vertical
2564 * and horizontal scroll movement.
2567 /* horizontal count */
2568 if (pb->ipacket[2] & 0x0f)
2569 *z = (pb->ipacket[2] & MOUSE_SPOINT_WNEG) ?
2571 /* vertical count */
2572 if (pb->ipacket[2] & 0xf0)
2573 *z = (pb->ipacket[2] & MOUSE_SPOINT_ZNEG) ?
2577 /* device type packet - shouldn't happen */
2581 ms->button = ms->obutton;
2582 VLOG(1, (LOG_DEBUG, "psmintr: unknown PS2++ packet "
2583 "type %d: 0x%02x 0x%02x 0x%02x\n",
2584 MOUSE_PS2PLUS_PACKET_TYPE(pb->ipacket),
2585 pb->ipacket[0], pb->ipacket[1], pb->ipacket[2]));
2589 /* preserve button states */
2590 ms->button |= ms->obutton & MOUSE_EXTBUTTONS;
2595 proc_synaptics(struct psm_softc *sc, packetbuf_t *pb, mousestatus_t *ms,
2596 int *x, int *y, int *z)
2598 static int touchpad_buttons;
2599 static int guest_buttons;
2602 /* TouchPad PS/2 absolute mode message format
2604 * Bits: 7 6 5 4 3 2 1 0 (LSB)
2605 * ------------------------------------------------
2606 * ipacket[0]: 1 0 W3 W2 0 W1 R L
2607 * ipacket[1]: Yb Ya Y9 Y8 Xb Xa X9 X8
2608 * ipacket[2]: Z7 Z6 Z5 Z4 Z3 Z2 Z1 Z0
2609 * ipacket[3]: 1 1 Yc Xc 0 W0 D U
2610 * ipacket[4]: X7 X6 X5 X4 X3 X2 X1 X0
2611 * ipacket[5]: Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
2614 * L: left physical mouse button
2615 * R: right physical mouse button
2623 * Absolute reportable limits: 0 - 6143.
2624 * Typical bezel limits: 1472 - 5472.
2625 * Typical edge marings: 1632 - 5312.
2627 * w = 3 Passthrough Packet
2629 * Byte 2,5,6 == Byte 1,2,3 of "Guest"
2632 if (!synaptics_support)
2635 /* Sanity check for out of sync packets. */
2636 if ((pb->ipacket[0] & 0xc8) != 0x80 ||
2637 (pb->ipacket[3] & 0xc8) != 0xc0)
2645 * z = 0 No finger contact
2646 * z = 10 Finger hovering near the pad
2647 * z = 30 Very light finger contact
2648 * z = 80 Normal finger contact
2649 * z = 110 Very heavy finger contact
2650 * z = 200 Finger lying flat on pad surface
2651 * z = 255 Maximum reportable Z
2653 *z = pb->ipacket[2];
2656 * Finger width value
2658 * w = 0 Two finger on the pad (capMultiFinger needed)
2659 * w = 1 Three or more fingers (capMultiFinger needed)
2660 * w = 2 Pen (instead of finger) (capPen needed)
2661 * w = 3 Reserved (passthrough?)
2662 * w = 4-7 Finger of normal width (capPalmDetect needed)
2663 * w = 8-14 Very wide finger or palm (capPalmDetect needed)
2664 * w = 15 Maximum reportable width (capPalmDetect needed)
2666 /* XXX Is checking capExtended enough? */
2667 if (sc->synhw.capExtended)
2668 w = ((pb->ipacket[0] & 0x30) >> 2) |
2669 ((pb->ipacket[0] & 0x04) >> 1) |
2670 ((pb->ipacket[3] & 0x04) >> 2);
2672 /* Assume a finger of regular width. */
2676 /* Handle packets from the guest device */
2677 /* XXX Documentation? */
2678 if (w == 3 && sc->synhw.capPassthrough) {
2679 *x = ((pb->ipacket[1] & 0x10) ?
2680 pb->ipacket[4] - 256 : pb->ipacket[4]);
2681 *y = ((pb->ipacket[1] & 0x20) ?
2682 pb->ipacket[5] - 256 : pb->ipacket[5]);
2686 if (pb->ipacket[1] & 0x01)
2687 guest_buttons |= MOUSE_BUTTON1DOWN;
2688 if (pb->ipacket[1] & 0x04)
2689 guest_buttons |= MOUSE_BUTTON2DOWN;
2690 if (pb->ipacket[1] & 0x02)
2691 guest_buttons |= MOUSE_BUTTON3DOWN;
2693 ms->button = touchpad_buttons | guest_buttons;
2697 /* Button presses */
2698 touchpad_buttons = 0;
2699 if (pb->ipacket[0] & 0x01)
2700 touchpad_buttons |= MOUSE_BUTTON1DOWN;
2701 if (pb->ipacket[0] & 0x02)
2702 touchpad_buttons |= MOUSE_BUTTON3DOWN;
2704 if (sc->synhw.capExtended && sc->synhw.capFourButtons) {
2705 if ((pb->ipacket[3] & 0x01) && (pb->ipacket[0] & 0x01) == 0)
2706 touchpad_buttons |= MOUSE_BUTTON4DOWN;
2707 if ((pb->ipacket[3] & 0x02) && (pb->ipacket[0] & 0x02) == 0)
2708 touchpad_buttons |= MOUSE_BUTTON5DOWN;
2712 * In newer pads - bit 0x02 in the third byte of
2713 * the packet indicates that we have an extended
2716 /* XXX Documentation? */
2717 if (pb->ipacket[3] & 0x02) {
2719 * if directional_scrolls is not 1, we treat any of
2720 * the scrolling directions as middle-click.
2722 if (sc->syninfo.directional_scrolls) {
2723 if (pb->ipacket[4] & 0x01)
2724 touchpad_buttons |= MOUSE_BUTTON4DOWN;
2725 if (pb->ipacket[5] & 0x01)
2726 touchpad_buttons |= MOUSE_BUTTON5DOWN;
2727 if (pb->ipacket[4] & 0x02)
2728 touchpad_buttons |= MOUSE_BUTTON6DOWN;
2729 if (pb->ipacket[5] & 0x02)
2730 touchpad_buttons |= MOUSE_BUTTON7DOWN;
2732 if ((pb->ipacket[4] & 0x0F) ||
2733 (pb->ipacket[5] & 0x0F))
2734 touchpad_buttons |= MOUSE_BUTTON2DOWN;
2738 ms->button = touchpad_buttons | guest_buttons;
2740 /* Check pressure to detect a real wanted action on the
2742 if (*z >= sc->syninfo.min_pressure) {
2743 synapticsaction_t *synaction;
2744 int cursor, peer, window;
2745 int dx, dy, dxp, dyp;
2746 int max_width, max_pressure;
2747 int margin_top, margin_right, margin_bottom, margin_left;
2748 int na_top, na_right, na_bottom, na_left;
2749 int window_min, window_max;
2751 int weight_current, weight_previous, weight_len_squared;
2752 int div_min, div_max, div_len;
2753 int vscroll_hor_area, vscroll_ver_area;
2755 int len, weight_prev_x, weight_prev_y;
2756 int div_max_x, div_max_y, div_x, div_y;
2759 /* XXX Verify values? */
2760 max_width = sc->syninfo.max_width;
2761 max_pressure = sc->syninfo.max_pressure;
2762 margin_top = sc->syninfo.margin_top;
2763 margin_right = sc->syninfo.margin_right;
2764 margin_bottom = sc->syninfo.margin_bottom;
2765 margin_left = sc->syninfo.margin_left;
2766 na_top = sc->syninfo.na_top;
2767 na_right = sc->syninfo.na_right;
2768 na_bottom = sc->syninfo.na_bottom;
2769 na_left = sc->syninfo.na_left;
2770 window_min = sc->syninfo.window_min;
2771 window_max = sc->syninfo.window_max;
2772 multiplicator = sc->syninfo.multiplicator;
2773 weight_current = sc->syninfo.weight_current;
2774 weight_previous = sc->syninfo.weight_previous;
2775 weight_len_squared = sc->syninfo.weight_len_squared;
2776 div_min = sc->syninfo.div_min;
2777 div_max = sc->syninfo.div_max;
2778 div_len = sc->syninfo.div_len;
2779 vscroll_hor_area = sc->syninfo.vscroll_hor_area;
2780 vscroll_ver_area = sc->syninfo.vscroll_ver_area;
2782 /* Palm detection. */
2784 (sc->synhw.capMultiFinger && (w == 0 || w == 1)) ||
2785 (sc->synhw.capPalmDetect && w >= 4 && w <= max_width) ||
2786 (!sc->synhw.capPalmDetect && *z <= max_pressure) ||
2787 (sc->synhw.capPen && w == 2))) {
2789 * We consider the packet irrelevant for the current
2791 * - the width isn't comprised in:
2793 * - the pressure isn't comprised in:
2794 * [min_pressure; max_pressure]
2795 * - pen aren't supported but w is 2
2797 * Note that this doesn't terminate the current action.
2800 "synaptics: palm detected! (%d)\n", w));
2804 /* Read current absolute position. */
2805 x0 = ((pb->ipacket[3] & 0x10) << 8) |
2806 ((pb->ipacket[1] & 0x0f) << 8) |
2808 y0 = ((pb->ipacket[3] & 0x20) << 7) |
2809 ((pb->ipacket[1] & 0xf0) << 4) |
2812 synaction = &(sc->synaction);
2815 * If the action is just beginning, init the structure and
2816 * compute tap timeout.
2818 if (!(sc->flags & PSM_FLAGS_FINGERDOWN)) {
2819 VLOG(3, (LOG_DEBUG, "synaptics: ----\n"));
2821 /* Store the first point of this action. */
2822 synaction->start_x = x0;
2823 synaction->start_y = y0;
2826 /* Initialize queue. */
2827 synaction->queue_cursor = SYNAPTICS_PACKETQUEUE;
2828 synaction->queue_len = 0;
2829 synaction->window_min = window_min;
2831 /* Reset average. */
2832 synaction->avg_dx = 0;
2833 synaction->avg_dy = 0;
2835 /* Reset squelch. */
2836 synaction->squelch_x = 0;
2837 synaction->squelch_y = 0;
2839 /* Reset pressure peak. */
2842 /* Reset fingers count. */
2843 synaction->fingers_nb = 0;
2845 /* Reset virtual scrolling state. */
2846 synaction->in_vscroll = 0;
2848 /* Compute tap timeout. */
2849 sc->taptimeout.tv_sec = tap_timeout / 1000000;
2850 sc->taptimeout.tv_usec = tap_timeout % 1000000;
2851 timevaladd(&sc->taptimeout, &sc->lastsoftintr);
2853 sc->flags |= PSM_FLAGS_FINGERDOWN;
2855 /* Calculate the current delta. */
2856 cursor = synaction->queue_cursor;
2857 dx = x0 - synaction->queue[cursor].x;
2858 dy = y0 - synaction->queue[cursor].y;
2861 /* If in tap-hold, add the recorded button. */
2862 if (synaction->in_taphold)
2863 ms->button |= synaction->tap_button;
2866 * From now on, we can use the SYNAPTICS_END label to skip
2867 * the current packet.
2871 * Limit the coordinates to the specified margins because
2872 * this area isn't very reliable.
2874 if (x0 <= margin_left)
2876 else if (x0 >= 6143 - margin_right)
2877 x0 = 6143 - margin_right;
2878 if (y0 <= margin_bottom)
2880 else if (y0 >= 6143 - margin_top)
2881 y0 = 6143 - margin_top;
2883 VLOG(3, (LOG_DEBUG, "synaptics: ipacket: [%d, %d], %d, %d\n",
2886 /* Queue this new packet. */
2887 cursor = SYNAPTICS_QUEUE_CURSOR(synaction->queue_cursor - 1);
2888 synaction->queue[cursor].x = x0;
2889 synaction->queue[cursor].y = y0;
2890 synaction->queue_cursor = cursor;
2891 if (synaction->queue_len < SYNAPTICS_PACKETQUEUE)
2892 synaction->queue_len++;
2894 "synaptics: cursor[%d]: x=%d, y=%d, dx=%d, dy=%d\n",
2895 cursor, x0, y0, dx, dy));
2898 * For tap, we keep the maximum number of fingers and the
2899 * pressure peak. Also with multiple fingers, we increase
2900 * the minimum window.
2903 case 1: /* Three or more fingers. */
2904 synaction->fingers_nb = imax(3, synaction->fingers_nb);
2905 synaction->window_min = window_max;
2907 case 0: /* Two fingers. */
2908 synaction->fingers_nb = imax(2, synaction->fingers_nb);
2909 synaction->window_min = window_max;
2911 default: /* One finger or undetectable. */
2912 synaction->fingers_nb = imax(1, synaction->fingers_nb);
2914 sc->zmax = imax(*z, sc->zmax);
2916 /* Do we have enough packets to consider this a movement? */
2917 if (synaction->queue_len < synaction->window_min)
2920 /* Is a scrolling action occuring? */
2921 if (!synaction->in_taphold && !synaction->in_vscroll) {
2923 * A scrolling action must not conflict with a tap
2924 * action. Here are the conditions to consider a
2926 * - the action in a configurable area
2927 * - one of the following:
2928 * . the distance between the last packet and the
2929 * first should be above a configurable minimum
2932 dxp = abs(synaction->queue[synaction->queue_cursor].x -
2933 synaction->start_x);
2934 dyp = abs(synaction->queue[synaction->queue_cursor].y -
2935 synaction->start_y);
2937 if (timevalcmp(&sc->lastsoftintr, &sc->taptimeout, >) ||
2938 dxp >= sc->syninfo.vscroll_min_delta ||
2939 dyp >= sc->syninfo.vscroll_min_delta) {
2940 /* Check for horizontal scrolling. */
2941 if ((vscroll_hor_area > 0 &&
2942 synaction->start_y <= vscroll_hor_area) ||
2943 (vscroll_hor_area < 0 &&
2944 synaction->start_y >=
2945 6143 + vscroll_hor_area))
2946 synaction->in_vscroll += 2;
2948 /* Check for vertical scrolling. */
2949 if ((vscroll_ver_area > 0 &&
2950 synaction->start_x <= vscroll_ver_area) ||
2951 (vscroll_ver_area < 0 &&
2952 synaction->start_x >=
2953 6143 + vscroll_ver_area))
2954 synaction->in_vscroll += 1;
2956 /* Avoid conflicts if area overlaps. */
2957 if (synaction->in_vscroll == 3)
2958 synaction->in_vscroll =
2959 (dxp > dyp) ? 2 : 1;
2962 "synaptics: virtual scrolling: %s "
2963 "(direction=%d, dxp=%d, dyp=%d)\n",
2964 synaction->in_vscroll ? "YES" : "NO",
2965 synaction->in_vscroll, dxp, dyp));
2968 weight_prev_x = weight_prev_y = weight_previous;
2969 div_max_x = div_max_y = div_max;
2971 if (synaction->in_vscroll) {
2972 /* Dividers are different with virtual scrolling. */
2973 div_min = sc->syninfo.vscroll_div_min;
2974 div_max_x = div_max_y = sc->syninfo.vscroll_div_max;
2977 * There's a lot of noise in coordinates when
2978 * the finger is on the touchpad's borders. When
2979 * using this area, we apply a special weight and
2982 if (x0 <= na_left || x0 >= 6143 - na_right) {
2983 weight_prev_x = sc->syninfo.weight_previous_na;
2984 div_max_x = sc->syninfo.div_max_na;
2987 if (y0 <= na_bottom || y0 >= 6143 - na_top) {
2988 weight_prev_y = sc->syninfo.weight_previous_na;
2989 div_max_y = sc->syninfo.div_max_na;
2994 * Calculate weights for the average operands and
2995 * the divisor. Both depend on the distance between
2996 * the current packet and a previous one (based on the
2999 window = imin(synaction->queue_len, window_max);
3000 peer = SYNAPTICS_QUEUE_CURSOR(cursor + window - 1);
3001 dxp = abs(x0 - synaction->queue[peer].x) + 1;
3002 dyp = abs(y0 - synaction->queue[peer].y) + 1;
3003 len = (dxp * dxp) + (dyp * dyp);
3004 weight_prev_x = imin(weight_prev_x,
3005 weight_len_squared * weight_prev_x / len);
3006 weight_prev_y = imin(weight_prev_y,
3007 weight_len_squared * weight_prev_y / len);
3009 len = (dxp + dyp) / 2;
3010 div_x = div_len * div_max_x / len;
3011 div_x = imin(div_max_x, div_x);
3012 div_x = imax(div_min, div_x);
3013 div_y = div_len * div_max_y / len;
3014 div_y = imin(div_max_y, div_y);
3015 div_y = imax(div_min, div_y);
3018 "synaptics: peer=%d, len=%d, weight=%d/%d, div=%d/%d\n",
3019 peer, len, weight_prev_x, weight_prev_y, div_x, div_y));
3021 /* Compute averages. */
3023 (weight_current * dx * multiplicator +
3024 weight_prev_x * synaction->avg_dx) /
3025 (weight_current + weight_prev_x);
3028 (weight_current * dy * multiplicator +
3029 weight_prev_y * synaction->avg_dy) /
3030 (weight_current + weight_prev_y);
3033 "synaptics: avg_dx~=%d, avg_dy~=%d\n",
3034 synaction->avg_dx / multiplicator,
3035 synaction->avg_dy / multiplicator));
3037 /* Use these averages to calculate x & y. */
3038 synaction->squelch_x += synaction->avg_dx;
3039 *x = synaction->squelch_x / (div_x * multiplicator);
3040 synaction->squelch_x = synaction->squelch_x %
3041 (div_x * multiplicator);
3043 synaction->squelch_y += synaction->avg_dy;
3044 *y = synaction->squelch_y / (div_y * multiplicator);
3045 synaction->squelch_y = synaction->squelch_y %
3046 (div_y * multiplicator);
3048 if (synaction->in_vscroll) {
3049 switch(synaction->in_vscroll) {
3050 case 1: /* Vertical scrolling. */
3052 ms->button |= (*y > 0) ?
3056 case 2: /* Horizontal scrolling. */
3058 ms->button |= (*x > 0) ?
3064 /* The pointer is not moved. */
3067 VLOG(3, (LOG_DEBUG, "synaptics: [%d, %d] -> [%d, %d]\n",
3070 } else if (sc->flags & PSM_FLAGS_FINGERDOWN) {
3072 * An action is currently taking place but the pressure
3073 * dropped under the minimum, putting an end to it.
3075 synapticsaction_t *synaction;
3076 int taphold_timeout, dx, dy, tap_max_delta;
3078 synaction = &(sc->synaction);
3079 dx = abs(synaction->queue[synaction->queue_cursor].x -
3080 synaction->start_x);
3081 dy = abs(synaction->queue[synaction->queue_cursor].y -
3082 synaction->start_y);
3084 /* Max delta is disabled for multi-fingers tap. */
3085 if (synaction->fingers_nb > 1)
3086 tap_max_delta = imax(dx, dy);
3088 tap_max_delta = sc->syninfo.tap_max_delta;
3090 sc->flags &= ~PSM_FLAGS_FINGERDOWN;
3092 /* Check for tap. */
3094 "synaptics: zmax=%d, dx=%d, dy=%d, "
3095 "delta=%d, fingers=%d, queue=%d\n",
3096 sc->zmax, dx, dy, tap_max_delta, synaction->fingers_nb,
3097 synaction->queue_len));
3098 if (!synaction->in_vscroll && sc->zmax >= tap_threshold &&
3099 timevalcmp(&sc->lastsoftintr, &sc->taptimeout, <=) &&
3100 dx <= tap_max_delta && dy <= tap_max_delta &&
3101 synaction->queue_len >= sc->syninfo.tap_min_queue) {
3104 * - the maximum pressure went over tap_threshold
3105 * - the action ended before tap_timeout
3107 * To handle tap-hold, we must delay any button push to
3110 if (synaction->in_taphold) {
3112 * This is the second and last tap of a
3113 * double tap action, not a tap-hold.
3115 synaction->in_taphold = 0;
3118 * For double-tap to work:
3119 * - no button press is emitted (to
3120 * simulate a button release)
3121 * - PSM_FLAGS_FINGERDOWN is set to
3122 * force the next packet to emit a
3126 "synaptics: button RELEASE: %d\n",
3127 synaction->tap_button));
3128 sc->flags |= PSM_FLAGS_FINGERDOWN;
3131 * This is the first tap: we set the
3132 * tap-hold state and notify the button
3135 synaction->in_taphold = 1;
3136 taphold_timeout = sc->syninfo.taphold_timeout;
3137 sc->taptimeout.tv_sec = taphold_timeout /
3139 sc->taptimeout.tv_usec = taphold_timeout %
3141 timevaladd(&sc->taptimeout, &sc->lastsoftintr);
3143 switch (synaction->fingers_nb) {
3145 synaction->tap_button =
3149 synaction->tap_button =
3153 synaction->tap_button =
3157 "synaptics: button PRESS: %d\n",
3158 synaction->tap_button));
3159 ms->button |= synaction->tap_button;
3163 * Not enough pressure or timeout: reset
3166 if (synaction->in_taphold) {
3168 "synaptics: button RELEASE: %d\n",
3169 synaction->tap_button));
3170 synaction->in_taphold = 0;
3173 "synaptics: not a tap-hold\n"));
3176 } else if (!(sc->flags & PSM_FLAGS_FINGERDOWN) &&
3177 sc->synaction.in_taphold) {
3179 * For a tap-hold to work, the button must remain down at
3180 * least until timeout (where the in_taphold flags will be
3181 * cleared) or during the next action.
3183 if (timevalcmp(&sc->lastsoftintr, &sc->taptimeout, <=)) {
3184 ms->button |= sc->synaction.tap_button;
3187 "synaptics: button RELEASE: %d\n",
3188 sc->synaction.tap_button));
3189 sc->synaction.in_taphold = 0;
3195 * Use the extra buttons as a scrollwheel
3197 * XXX X.Org uses the Z axis for vertical wheel only,
3198 * whereas moused(8) understands special values to differ
3199 * vertical and horizontal wheels.
3201 * xf86-input-mouse needs therefore a small patch to
3202 * understand these special values. Without it, the
3203 * horizontal wheel acts as a vertical wheel in X.Org.
3205 * That's why the horizontal wheel is disabled by
3208 if (ms->button & MOUSE_BUTTON4DOWN) {
3210 ms->button &= ~MOUSE_BUTTON4DOWN;
3211 } else if (ms->button & MOUSE_BUTTON5DOWN) {
3213 ms->button &= ~MOUSE_BUTTON5DOWN;
3214 } else if (ms->button & MOUSE_BUTTON6DOWN) {
3216 ms->button &= ~MOUSE_BUTTON6DOWN;
3217 } else if (ms->button & MOUSE_BUTTON7DOWN) {
3219 ms->button &= ~MOUSE_BUTTON7DOWN;
3227 proc_versapad(struct psm_softc *sc, packetbuf_t *pb, mousestatus_t *ms,
3228 int *x, int *y, int *z)
3230 static int butmap_versapad[8] = {
3236 MOUSE_BUTTON1DOWN | MOUSE_BUTTON3DOWN,
3238 MOUSE_BUTTON1DOWN | MOUSE_BUTTON3DOWN
3242 /* VersaPad PS/2 absolute mode message format
3244 * [packet1] 7 6 5 4 3 2 1 0(LSB)
3245 * ipacket[0]: 1 1 0 A 1 L T R
3246 * ipacket[1]: H7 H6 H5 H4 H3 H2 H1 H0
3247 * ipacket[2]: V7 V6 V5 V4 V3 V2 V1 V0
3248 * ipacket[3]: 1 1 1 A 1 L T R
3249 * ipacket[4]:V11 V10 V9 V8 H11 H10 H9 H8
3250 * ipacket[5]: 0 P6 P5 P4 P3 P2 P1 P0
3253 * R: right physical mouse button (1=on)
3254 * T: touch pad virtual button (1=tapping)
3255 * L: left physical mouse button (1=on)
3256 * A: position data is valid (1=valid)
3257 * H: horizontal data (12bit signed integer. H11 is sign bit.)
3258 * V: vertical data (12bit signed integer. V11 is sign bit.)
3261 * Tapping is mapped to MOUSE_BUTTON4.
3265 ms->button = butmap_versapad[c & MOUSE_PS2VERSA_BUTTONS];
3266 ms->button |= (c & MOUSE_PS2VERSA_TAP) ? MOUSE_BUTTON4DOWN : 0;
3267 if (c & MOUSE_PS2VERSA_IN_USE) {
3268 x0 = pb->ipacket[1] | (((pb->ipacket[4]) & 0x0f) << 8);
3269 y0 = pb->ipacket[2] | (((pb->ipacket[4]) & 0xf0) << 4);
3274 if (sc->flags & PSM_FLAGS_FINGERDOWN) {
3277 if (*x < 0) /* XXX */
3286 sc->flags |= PSM_FLAGS_FINGERDOWN;
3290 sc->flags &= ~PSM_FLAGS_FINGERDOWN;
3294 psmsoftintr(void *arg)
3297 * the table to turn PS/2 mouse button bits (MOUSE_PS2_BUTTON?DOWN)
3298 * into `mousestatus' button bits (MOUSE_BUTTON?DOWN).
3300 static int butmap[8] = {
3304 MOUSE_BUTTON1DOWN | MOUSE_BUTTON3DOWN,
3306 MOUSE_BUTTON1DOWN | MOUSE_BUTTON2DOWN,
3307 MOUSE_BUTTON2DOWN | MOUSE_BUTTON3DOWN,
3308 MOUSE_BUTTON1DOWN | MOUSE_BUTTON2DOWN | MOUSE_BUTTON3DOWN
3310 struct psm_softc *sc = arg;
3313 int x, y, z, c, l, s;
3315 getmicrouptime(&sc->lastsoftintr);
3320 pb = &sc->pqueue[sc->pqueue_start];
3322 if (sc->mode.level == PSM_LEVEL_NATIVE)
3327 * A kludge for Kensington device!
3328 * The MSB of the horizontal count appears to be stored in
3331 if (sc->hw.model == MOUSE_MODEL_THINK)
3332 pb->ipacket[1] |= (c & MOUSE_PS2_XOVERFLOW) ? 0x80 : 0;
3334 /* ignore the overflow bits... */
3335 x = (c & MOUSE_PS2_XNEG) ?
3336 pb->ipacket[1] - 256 : pb->ipacket[1];
3337 y = (c & MOUSE_PS2_YNEG) ?
3338 pb->ipacket[2] - 256 : pb->ipacket[2];
3340 ms.obutton = sc->button; /* previous button state */
3341 ms.button = butmap[c & MOUSE_PS2_BUTTONS];
3342 /* `tapping' action */
3343 if (sc->config & PSM_CONFIG_FORCETAP)
3344 ms.button |= ((c & MOUSE_PS2_TAP)) ?
3345 0 : MOUSE_BUTTON4DOWN;
3347 switch (sc->hw.model) {
3349 case MOUSE_MODEL_EXPLORER:
3351 * b7 b6 b5 b4 b3 b2 b1 b0
3352 * byte 1: oy ox sy sx 1 M R L
3353 * byte 2: x x x x x x x x
3354 * byte 3: y y y y y y y y
3355 * byte 4: * * S2 S1 s d2 d1 d0
3357 * L, M, R, S1, S2: left, middle, right and side buttons
3358 * s: wheel data sign bit
3361 z = (pb->ipacket[3] & MOUSE_EXPLORER_ZNEG) ?
3362 (pb->ipacket[3] & 0x0f) - 16 :
3363 (pb->ipacket[3] & 0x0f);
3365 (pb->ipacket[3] & MOUSE_EXPLORER_BUTTON4DOWN) ?
3366 MOUSE_BUTTON4DOWN : 0;
3368 (pb->ipacket[3] & MOUSE_EXPLORER_BUTTON5DOWN) ?
3369 MOUSE_BUTTON5DOWN : 0;
3372 case MOUSE_MODEL_INTELLI:
3373 case MOUSE_MODEL_NET:
3374 /* wheel data is in the fourth byte */
3375 z = (char)pb->ipacket[3];
3377 * XXX some mice may send 7 when there is no Z movement? */
3378 if ((z >= 7) || (z <= -7))
3380 /* some compatible mice have additional buttons */
3381 ms.button |= (c & MOUSE_PS2INTELLI_BUTTON4DOWN) ?
3382 MOUSE_BUTTON4DOWN : 0;
3383 ms.button |= (c & MOUSE_PS2INTELLI_BUTTON5DOWN) ?
3384 MOUSE_BUTTON5DOWN : 0;
3387 case MOUSE_MODEL_MOUSEMANPLUS:
3388 proc_mmanplus(sc, pb, &ms, &x, &y, &z);
3391 case MOUSE_MODEL_GLIDEPOINT:
3392 /* `tapping' action */
3393 ms.button |= ((c & MOUSE_PS2_TAP)) ? 0 :
3397 case MOUSE_MODEL_NETSCROLL:
3399 * three addtional bytes encode buttons and
3402 ms.button |= (pb->ipacket[3] & MOUSE_PS2_BUTTON3DOWN) ?
3403 MOUSE_BUTTON4DOWN : 0;
3404 ms.button |= (pb->ipacket[3] & MOUSE_PS2_BUTTON1DOWN) ?
3405 MOUSE_BUTTON5DOWN : 0;
3406 z = (pb->ipacket[3] & MOUSE_PS2_XNEG) ?
3407 pb->ipacket[4] - 256 : pb->ipacket[4];
3410 case MOUSE_MODEL_THINK:
3411 /* the fourth button state in the first byte */
3412 ms.button |= (c & MOUSE_PS2_TAP) ?
3413 MOUSE_BUTTON4DOWN : 0;
3416 case MOUSE_MODEL_VERSAPAD:
3417 proc_versapad(sc, pb, &ms, &x, &y, &z);
3418 c = ((x < 0) ? MOUSE_PS2_XNEG : 0) |
3419 ((y < 0) ? MOUSE_PS2_YNEG : 0);
3422 case MOUSE_MODEL_4D:
3424 * b7 b6 b5 b4 b3 b2 b1 b0
3425 * byte 1: s2 d2 s1 d1 1 M R L
3426 * byte 2: sx x x x x x x x
3427 * byte 3: sy y y y y y y y
3429 * s1: wheel 1 direction
3431 * s2: wheel 2 direction
3434 x = (pb->ipacket[1] & 0x80) ?
3435 pb->ipacket[1] - 256 : pb->ipacket[1];
3436 y = (pb->ipacket[2] & 0x80) ?
3437 pb->ipacket[2] - 256 : pb->ipacket[2];
3438 switch (c & MOUSE_4D_WHEELBITS) {
3445 case 0x40: /* XXX 2nd wheel turning right */
3448 case 0xc0: /* XXX 2nd wheel turning left */
3454 case MOUSE_MODEL_4DPLUS:
3455 if ((x < 16 - 256) && (y < 16 - 256)) {
3457 * b7 b6 b5 b4 b3 b2 b1 b0
3458 * byte 1: 0 0 1 1 1 M R L
3459 * byte 2: 0 0 0 0 1 0 0 0
3460 * byte 3: 0 0 0 0 S s d1 d0
3462 * L, M, R, S: left, middle, right,
3464 * s: wheel data sign bit
3468 if (pb->ipacket[2] & MOUSE_4DPLUS_BUTTON4DOWN)
3469 ms.button |= MOUSE_BUTTON4DOWN;
3470 z = (pb->ipacket[2] & MOUSE_4DPLUS_ZNEG) ?
3471 ((pb->ipacket[2] & 0x07) - 8) :
3472 (pb->ipacket[2] & 0x07) ;
3474 /* preserve previous button states */
3475 ms.button |= ms.obutton & MOUSE_EXTBUTTONS;
3479 case MOUSE_MODEL_SYNAPTICS:
3480 if (proc_synaptics(sc, pb, &ms, &x, &y, &z) != 0)
3484 case MOUSE_MODEL_TRACKPOINT:
3485 case MOUSE_MODEL_GENERIC:
3491 if (sc->mode.accelfactor >= 1) {
3493 x = x * x / sc->mode.accelfactor;
3496 if (c & MOUSE_PS2_XNEG)
3500 y = y * y / sc->mode.accelfactor;
3503 if (c & MOUSE_PS2_YNEG)
3511 ms.flags = ((x || y || z) ? MOUSE_POSCHANGED : 0) |
3512 (ms.obutton ^ ms.button);
3514 pb->inputbytes = tame_mouse(sc, pb, &ms, pb->ipacket);
3516 sc->status.flags |= ms.flags;
3517 sc->status.dx += ms.dx;
3518 sc->status.dy += ms.dy;
3519 sc->status.dz += ms.dz;
3520 sc->status.button = ms.button;
3521 sc->button = ms.button;
3524 sc->watchdog = FALSE;
3527 if (sc->queue.count + pb->inputbytes < sizeof(sc->queue.buf)) {
3528 l = imin(pb->inputbytes,
3529 sizeof(sc->queue.buf) - sc->queue.tail);
3530 bcopy(&pb->ipacket[0], &sc->queue.buf[sc->queue.tail], l);
3531 if (pb->inputbytes > l)
3532 bcopy(&pb->ipacket[l], &sc->queue.buf[0],
3533 pb->inputbytes - l);
3534 sc->queue.tail = (sc->queue.tail + pb->inputbytes) %
3535 sizeof(sc->queue.buf);
3536 sc->queue.count += pb->inputbytes;
3541 if (++sc->pqueue_start >= PSM_PACKETQUEUE)
3542 sc->pqueue_start = 0;
3543 } while (sc->pqueue_start != sc->pqueue_end);
3545 if (sc->state & PSM_ASLP) {
3546 sc->state &= ~PSM_ASLP;
3549 selwakeuppri(&sc->rsel, PZERO);
3550 if (sc->async != NULL) {
3551 pgsigio(&sc->async, SIGIO, 0);
3553 sc->state &= ~PSM_SOFTARMED;
3558 psmpoll(struct cdev *dev, int events, struct thread *td)
3560 struct psm_softc *sc = dev->si_drv1;
3564 /* Return true if a mouse event available */
3566 if (events & (POLLIN | POLLRDNORM)) {
3567 if (sc->queue.count > 0)
3568 revents |= events & (POLLIN | POLLRDNORM);
3570 selrecord(td, &sc->rsel);
3577 /* vendor/model specific routines */
3579 static int mouse_id_proc1(KBDC kbdc, int res, int scale, int *status)
3581 if (set_mouse_resolution(kbdc, res) != res)
3583 if (set_mouse_scaling(kbdc, scale) &&
3584 set_mouse_scaling(kbdc, scale) &&
3585 set_mouse_scaling(kbdc, scale) &&
3586 (get_mouse_status(kbdc, status, 0, 3) >= 3))
3592 mouse_ext_command(KBDC kbdc, int command)
3596 c = (command >> 6) & 0x03;
3597 if (set_mouse_resolution(kbdc, c) != c)
3599 c = (command >> 4) & 0x03;
3600 if (set_mouse_resolution(kbdc, c) != c)
3602 c = (command >> 2) & 0x03;
3603 if (set_mouse_resolution(kbdc, c) != c)
3605 c = (command >> 0) & 0x03;
3606 if (set_mouse_resolution(kbdc, c) != c)
3612 /* Logitech MouseMan Cordless II */
3614 enable_lcordless(KDBC kbdc, struct psm_softc *sc)
3619 if (!mouse_id_proc1(kbdc, PSMD_RES_HIGH, 2, status))
3621 if (status[1] == PSMD_RES_HIGH)
3623 ch = (status[0] & 0x07) - 1; /* channel # */
3624 if ((ch <= 0) || (ch > 4))
3627 * status[1]: always one?
3628 * status[2]: battery status? (0-100)
3634 /* Genius NetScroll Mouse, MouseSystems SmartScroll Mouse */
3636 enable_groller(KBDC kbdc, struct psm_softc *sc)
3641 * The special sequence to enable the fourth button and the
3642 * roller. Immediately after this sequence check status bytes.
3643 * if the mouse is NetScroll, the second and the third bytes are
3648 * If the mouse is an ordinary PS/2 mouse, the status bytes should
3649 * look like the following.
3651 * byte 1 bit 7 always 0
3652 * bit 6 stream mode (0)
3653 * bit 5 disabled (0)
3654 * bit 4 1:1 scaling (0)
3656 * bit 0-2 button status
3657 * byte 2 resolution (PSMD_RES_HIGH)
3658 * byte 3 report rate (?)
3661 if (!mouse_id_proc1(kbdc, PSMD_RES_HIGH, 1, status))
3663 if ((status[1] != '3') || (status[2] != 'D'))
3665 /* FIXME: SmartScroll Mouse has 5 buttons! XXX */
3671 /* Genius NetMouse/NetMouse Pro, ASCII Mie Mouse, NetScroll Optical */
3673 enable_gmouse(KBDC kbdc, struct psm_softc *sc)
3678 * The special sequence to enable the middle, "rubber" button.
3679 * Immediately after this sequence check status bytes.
3680 * if the mouse is NetMouse, NetMouse Pro, or ASCII MIE Mouse,
3681 * the second and the third bytes are '3' and 'U'.
3682 * NOTE: NetMouse reports that it has three buttons although it has
3683 * two buttons and a rubber button. NetMouse Pro and MIE Mouse
3684 * say they have three buttons too and they do have a button on the
3687 if (!mouse_id_proc1(kbdc, PSMD_RES_HIGH, 1, status))
3689 if ((status[1] != '3') || (status[2] != 'U'))
3694 /* ALPS GlidePoint */
3696 enable_aglide(KBDC kbdc, struct psm_softc *sc)
3701 * The special sequence to obtain ALPS GlidePoint specific
3702 * information. Immediately after this sequence, status bytes will
3703 * contain something interesting.
3704 * NOTE: ALPS produces several models of GlidePoint. Some of those
3705 * do not respond to this sequence, thus, cannot be detected this way.
3707 if (set_mouse_sampling_rate(kbdc, 100) != 100)
3709 if (!mouse_id_proc1(kbdc, PSMD_RES_LOW, 2, status))
3711 if ((status[1] == PSMD_RES_LOW) || (status[2] == 100))
3716 /* Kensington ThinkingMouse/Trackball */
3718 enable_kmouse(KBDC kbdc, struct psm_softc *sc)
3720 static u_char rate[] = { 20, 60, 40, 20, 20, 60, 40, 20, 20 };
3726 id1 = get_aux_id(kbdc);
3727 if (set_mouse_sampling_rate(kbdc, 10) != 10)
3730 * The device is now in the native mode? It returns a different
3733 id2 = get_aux_id(kbdc);
3734 if ((id1 == id2) || (id2 != 2))
3737 if (set_mouse_resolution(kbdc, PSMD_RES_LOW) != PSMD_RES_LOW)
3740 /* at this point, resolution is LOW, sampling rate is 10/sec */
3741 if (get_mouse_status(kbdc, status, 0, 3) < 3)
3746 * The special sequence to enable the third and fourth buttons.
3747 * Otherwise they behave like the first and second buttons.
3749 for (i = 0; i < sizeof(rate)/sizeof(rate[0]); ++i)
3750 if (set_mouse_sampling_rate(kbdc, rate[i]) != rate[i])
3754 * At this point, the device is using default resolution and
3755 * sampling rate for the native mode.
3757 if (get_mouse_status(kbdc, status, 0, 3) < 3)
3759 if ((status[1] == PSMD_RES_LOW) || (status[2] == rate[i - 1]))
3762 /* the device appears be enabled by this sequence, diable it for now */
3763 disable_aux_dev(kbdc);
3764 empty_aux_buffer(kbdc, 5);
3769 /* Logitech MouseMan+/FirstMouse+, IBM ScrollPoint Mouse */
3771 enable_mmanplus(KBDC kbdc, struct psm_softc *sc)
3775 /* the special sequence to enable the fourth button and the roller. */
3777 * NOTE: for ScrollPoint to respond correctly, the SET_RESOLUTION
3778 * must be called exactly three times since the last RESET command
3779 * before this sequence. XXX
3781 if (!set_mouse_scaling(kbdc, 1))
3783 if (!mouse_ext_command(kbdc, 0x39) || !mouse_ext_command(kbdc, 0xdb))
3785 if (get_mouse_status(kbdc, data, 1, 3) < 3)
3789 * PS2++ protocol, packet type 0
3791 * b7 b6 b5 b4 b3 b2 b1 b0
3792 * byte 1: * 1 p3 p2 1 * * *
3793 * byte 2: 1 1 p1 p0 m1 m0 1 0
3794 * byte 3: m7 m6 m5 m4 m3 m2 m1 m0
3796 * p3-p0: packet type: 0
3797 * m7-m0: model ID: MouseMan+:0x50,
3799 * ScrollPoint:0x58...
3801 /* check constant bits */
3802 if ((data[0] & MOUSE_PS2PLUS_SYNCMASK) != MOUSE_PS2PLUS_SYNC)
3804 if ((data[1] & 0xc3) != 0xc2)
3806 /* check d3-d0 in byte 2 */
3807 if (!MOUSE_PS2PLUS_CHECKBITS(data))
3810 if (MOUSE_PS2PLUS_PACKET_TYPE(data) != 0)
3814 sc->hw.hwid &= 0x00ff;
3815 sc->hw.hwid |= data[2] << 8; /* save model ID */
3819 * MouseMan+ (or FirstMouse+) is now in its native mode, in which
3820 * the wheel and the fourth button events are encoded in the
3821 * special data packet. The mouse may be put in the IntelliMouse mode
3822 * if it is initialized by the IntelliMouse's method.
3827 /* MS IntelliMouse Explorer */
3829 enable_msexplorer(KBDC kbdc, struct psm_softc *sc)
3831 static u_char rate0[] = { 200, 100, 80, };
3832 static u_char rate1[] = { 200, 200, 80, };
3837 * This is needed for at least A4Tech X-7xx mice - they do not go
3838 * straight to Explorer mode, but need to be set to Intelli mode
3841 enable_msintelli(kbdc, sc);
3843 /* the special sequence to enable the extra buttons and the roller. */
3844 for (i = 0; i < sizeof(rate1)/sizeof(rate1[0]); ++i)
3845 if (set_mouse_sampling_rate(kbdc, rate1[i]) != rate1[i])
3847 /* the device will give the genuine ID only after the above sequence */
3848 id = get_aux_id(kbdc);
3849 if (id != PSM_EXPLORER_ID)
3853 sc->hw.buttons = 5; /* IntelliMouse Explorer XXX */
3858 * XXX: this is a kludge to fool some KVM switch products
3859 * which think they are clever enough to know the 4-byte IntelliMouse
3860 * protocol, and assume any other protocols use 3-byte packets.
3861 * They don't convey 4-byte data packets from the IntelliMouse Explorer
3862 * correctly to the host computer because of this!
3863 * The following sequence is actually IntelliMouse's "wake up"
3864 * sequence; it will make the KVM think the mouse is IntelliMouse
3865 * when it is in fact IntelliMouse Explorer.
3867 for (i = 0; i < sizeof(rate0)/sizeof(rate0[0]); ++i)
3868 if (set_mouse_sampling_rate(kbdc, rate0[i]) != rate0[i])
3875 /* MS IntelliMouse */
3877 enable_msintelli(KBDC kbdc, struct psm_softc *sc)
3880 * Logitech MouseMan+ and FirstMouse+ will also respond to this
3881 * probe routine and act like IntelliMouse.
3884 static u_char rate[] = { 200, 100, 80, };
3888 /* the special sequence to enable the third button and the roller. */
3889 for (i = 0; i < sizeof(rate)/sizeof(rate[0]); ++i)
3890 if (set_mouse_sampling_rate(kbdc, rate[i]) != rate[i])
3892 /* the device will give the genuine ID only after the above sequence */
3893 id = get_aux_id(kbdc);
3894 if (id != PSM_INTELLI_ID)
3905 /* A4 Tech 4D Mouse */
3907 enable_4dmouse(KBDC kbdc, struct psm_softc *sc)
3910 * Newer wheel mice from A4 Tech may use the 4D+ protocol.
3913 static u_char rate[] = { 200, 100, 80, 60, 40, 20 };
3917 for (i = 0; i < sizeof(rate)/sizeof(rate[0]); ++i)
3918 if (set_mouse_sampling_rate(kbdc, rate[i]) != rate[i])
3920 id = get_aux_id(kbdc);
3922 * WinEasy 4D, 4 Way Scroll 4D: 6
3923 * Cable-Free 4D: 8 (4DPLUS)
3924 * WinBest 4D+, 4 Way Scroll 4D+: 8 (4DPLUS)
3926 if (id != PSM_4DMOUSE_ID)
3930 sc->hw.buttons = 3; /* XXX some 4D mice have 4? */
3937 /* A4 Tech 4D+ Mouse */
3939 enable_4dplus(KBDC kbdc, struct psm_softc *sc)
3942 * Newer wheel mice from A4 Tech seem to use this protocol.
3943 * Older models are recognized as either 4D Mouse or IntelliMouse.
3948 * enable_4dmouse() already issued the following ID sequence...
3949 static u_char rate[] = { 200, 100, 80, 60, 40, 20 };
3952 for (i = 0; i < sizeof(rate)/sizeof(rate[0]); ++i)
3953 if (set_mouse_sampling_rate(kbdc, rate[i]) != rate[i])
3957 id = get_aux_id(kbdc);
3961 case PSM_4DPLUS_RFSW35_ID:
3968 sc->hw.buttons = (id == PSM_4DPLUS_ID) ? 4 : 3;
3975 /* Synaptics Touchpad */
3977 synaptics_sysctl(SYSCTL_HANDLER_ARGS)
3981 /* Read the current value. */
3982 arg = *(int *)oidp->oid_arg1;
3983 error = sysctl_handle_int(oidp, &arg, 0, req);
3986 if (error || !req->newptr)
3990 * Check that the new value is in the concerned node's range
3993 switch (oidp->oid_arg2) {
3994 case SYNAPTICS_SYSCTL_MIN_PRESSURE:
3995 case SYNAPTICS_SYSCTL_MAX_PRESSURE:
3996 if (arg < 0 || arg > 255)
3999 case SYNAPTICS_SYSCTL_MAX_WIDTH:
4000 if (arg < 4 || arg > 15)
4003 case SYNAPTICS_SYSCTL_MARGIN_TOP:
4004 case SYNAPTICS_SYSCTL_MARGIN_RIGHT:
4005 case SYNAPTICS_SYSCTL_MARGIN_BOTTOM:
4006 case SYNAPTICS_SYSCTL_MARGIN_LEFT:
4007 case SYNAPTICS_SYSCTL_NA_TOP:
4008 case SYNAPTICS_SYSCTL_NA_RIGHT:
4009 case SYNAPTICS_SYSCTL_NA_BOTTOM:
4010 case SYNAPTICS_SYSCTL_NA_LEFT:
4011 if (arg < 0 || arg > 6143)
4014 case SYNAPTICS_SYSCTL_WINDOW_MIN:
4015 case SYNAPTICS_SYSCTL_WINDOW_MAX:
4016 case SYNAPTICS_SYSCTL_TAP_MIN_QUEUE:
4017 if (arg < 1 || arg > SYNAPTICS_PACKETQUEUE)
4020 case SYNAPTICS_SYSCTL_MULTIPLICATOR:
4021 case SYNAPTICS_SYSCTL_WEIGHT_CURRENT:
4022 case SYNAPTICS_SYSCTL_WEIGHT_PREVIOUS:
4023 case SYNAPTICS_SYSCTL_WEIGHT_PREVIOUS_NA:
4024 case SYNAPTICS_SYSCTL_WEIGHT_LEN_SQUARED:
4025 case SYNAPTICS_SYSCTL_DIV_MIN:
4026 case SYNAPTICS_SYSCTL_DIV_MAX:
4027 case SYNAPTICS_SYSCTL_DIV_MAX_NA:
4028 case SYNAPTICS_SYSCTL_DIV_LEN:
4029 case SYNAPTICS_SYSCTL_VSCROLL_DIV_MIN:
4030 case SYNAPTICS_SYSCTL_VSCROLL_DIV_MAX:
4034 case SYNAPTICS_SYSCTL_TAP_MAX_DELTA:
4035 case SYNAPTICS_SYSCTL_TAPHOLD_TIMEOUT:
4036 case SYNAPTICS_SYSCTL_VSCROLL_MIN_DELTA:
4040 case SYNAPTICS_SYSCTL_VSCROLL_HOR_AREA:
4041 case SYNAPTICS_SYSCTL_VSCROLL_VER_AREA:
4042 if (arg < -6143 || arg > 6143)
4050 *(int *)oidp->oid_arg1 = arg;
4056 synaptics_sysctl_create_tree(struct psm_softc *sc)
4059 if (sc->syninfo.sysctl_tree != NULL)
4062 /* Attach extra synaptics sysctl nodes under hw.psm.synaptics */
4063 sysctl_ctx_init(&sc->syninfo.sysctl_ctx);
4064 sc->syninfo.sysctl_tree = SYSCTL_ADD_NODE(&sc->syninfo.sysctl_ctx,
4065 SYSCTL_STATIC_CHILDREN(_hw_psm), OID_AUTO, "synaptics", CTLFLAG_RD,
4066 0, "Synaptics TouchPad");
4068 /* hw.psm.synaptics.directional_scrolls. */
4069 sc->syninfo.directional_scrolls = 1;
4070 SYSCTL_ADD_INT(&sc->syninfo.sysctl_ctx,
4071 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4072 "directional_scrolls", CTLFLAG_RW|CTLFLAG_ANYBODY,
4073 &sc->syninfo.directional_scrolls, 0,
4074 "Enable hardware scrolling pad (if non-zero) or register it as "
4075 "a middle-click (if 0)");
4077 /* hw.psm.synaptics.min_pressure. */
4078 sc->syninfo.min_pressure = 16;
4079 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4080 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4081 "min_pressure", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4082 &sc->syninfo.min_pressure, SYNAPTICS_SYSCTL_MIN_PRESSURE,
4083 synaptics_sysctl, "I",
4084 "Minimum pressure required to start an action");
4086 /* hw.psm.synaptics.max_pressure. */
4087 sc->syninfo.max_pressure = 220;
4088 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4089 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4090 "max_pressure", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4091 &sc->syninfo.max_pressure, SYNAPTICS_SYSCTL_MAX_PRESSURE,
4092 synaptics_sysctl, "I",
4093 "Maximum pressure to detect palm");
4095 /* hw.psm.synaptics.max_width. */
4096 sc->syninfo.max_width = 10;
4097 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4098 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4099 "max_width", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4100 &sc->syninfo.max_width, SYNAPTICS_SYSCTL_MAX_WIDTH,
4101 synaptics_sysctl, "I",
4102 "Maximum finger width to detect palm");
4104 /* hw.psm.synaptics.top_margin. */
4105 sc->syninfo.margin_top = 200;
4106 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4107 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4108 "margin_top", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4109 &sc->syninfo.margin_top, SYNAPTICS_SYSCTL_MARGIN_TOP,
4110 synaptics_sysctl, "I",
4113 /* hw.psm.synaptics.right_margin. */
4114 sc->syninfo.margin_right = 200;
4115 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4116 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4117 "margin_right", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4118 &sc->syninfo.margin_right, SYNAPTICS_SYSCTL_MARGIN_RIGHT,
4119 synaptics_sysctl, "I",
4122 /* hw.psm.synaptics.bottom_margin. */
4123 sc->syninfo.margin_bottom = 200;
4124 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4125 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4126 "margin_bottom", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4127 &sc->syninfo.margin_bottom, SYNAPTICS_SYSCTL_MARGIN_BOTTOM,
4128 synaptics_sysctl, "I",
4131 /* hw.psm.synaptics.left_margin. */
4132 sc->syninfo.margin_left = 200;
4133 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4134 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4135 "margin_left", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4136 &sc->syninfo.margin_left, SYNAPTICS_SYSCTL_MARGIN_LEFT,
4137 synaptics_sysctl, "I",
4140 /* hw.psm.synaptics.na_top. */
4141 sc->syninfo.na_top = 1783;
4142 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4143 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4144 "na_top", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4145 &sc->syninfo.na_top, SYNAPTICS_SYSCTL_NA_TOP,
4146 synaptics_sysctl, "I",
4147 "Top noisy area, where weight_previous_na is used instead "
4148 "of weight_previous");
4150 /* hw.psm.synaptics.na_right. */
4151 sc->syninfo.na_right = 563;
4152 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4153 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4154 "na_right", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4155 &sc->syninfo.na_right, SYNAPTICS_SYSCTL_NA_RIGHT,
4156 synaptics_sysctl, "I",
4157 "Right noisy area, where weight_previous_na is used instead "
4158 "of weight_previous");
4160 /* hw.psm.synaptics.na_bottom. */
4161 sc->syninfo.na_bottom = 1408;
4162 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4163 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4164 "na_bottom", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4165 &sc->syninfo.na_bottom, SYNAPTICS_SYSCTL_NA_BOTTOM,
4166 synaptics_sysctl, "I",
4167 "Bottom noisy area, where weight_previous_na is used instead "
4168 "of weight_previous");
4170 /* hw.psm.synaptics.na_left. */
4171 sc->syninfo.na_left = 1600;
4172 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4173 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4174 "na_left", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4175 &sc->syninfo.na_left, SYNAPTICS_SYSCTL_NA_LEFT,
4176 synaptics_sysctl, "I",
4177 "Left noisy area, where weight_previous_na is used instead "
4178 "of weight_previous");
4180 /* hw.psm.synaptics.window_min. */
4181 sc->syninfo.window_min = 4;
4182 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4183 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4184 "window_min", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4185 &sc->syninfo.window_min, SYNAPTICS_SYSCTL_WINDOW_MIN,
4186 synaptics_sysctl, "I",
4187 "Minimum window size to start an action");
4189 /* hw.psm.synaptics.window_max. */
4190 sc->syninfo.window_max = 10;
4191 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4192 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4193 "window_max", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4194 &sc->syninfo.window_max, SYNAPTICS_SYSCTL_WINDOW_MAX,
4195 synaptics_sysctl, "I",
4196 "Maximum window size");
4198 /* hw.psm.synaptics.multiplicator. */
4199 sc->syninfo.multiplicator = 10000;
4200 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4201 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4202 "multiplicator", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4203 &sc->syninfo.multiplicator, SYNAPTICS_SYSCTL_MULTIPLICATOR,
4204 synaptics_sysctl, "I",
4205 "Multiplicator to increase precision in averages and divisions");
4207 /* hw.psm.synaptics.weight_current. */
4208 sc->syninfo.weight_current = 3;
4209 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4210 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4211 "weight_current", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4212 &sc->syninfo.weight_current, SYNAPTICS_SYSCTL_WEIGHT_CURRENT,
4213 synaptics_sysctl, "I",
4214 "Weight of the current movement in the new average");
4216 /* hw.psm.synaptics.weight_previous. */
4217 sc->syninfo.weight_previous = 6;
4218 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4219 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4220 "weight_previous", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4221 &sc->syninfo.weight_previous, SYNAPTICS_SYSCTL_WEIGHT_PREVIOUS,
4222 synaptics_sysctl, "I",
4223 "Weight of the previous average");
4225 /* hw.psm.synaptics.weight_previous_na. */
4226 sc->syninfo.weight_previous_na = 20;
4227 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4228 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4229 "weight_previous_na", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4230 &sc->syninfo.weight_previous_na,
4231 SYNAPTICS_SYSCTL_WEIGHT_PREVIOUS_NA,
4232 synaptics_sysctl, "I",
4233 "Weight of the previous average (inside the noisy area)");
4235 /* hw.psm.synaptics.weight_len_squared. */
4236 sc->syninfo.weight_len_squared = 2000;
4237 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4238 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4239 "weight_len_squared", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4240 &sc->syninfo.weight_len_squared,
4241 SYNAPTICS_SYSCTL_WEIGHT_LEN_SQUARED,
4242 synaptics_sysctl, "I",
4243 "Length (squared) of segments where weight_previous "
4244 "starts to decrease");
4246 /* hw.psm.synaptics.div_min. */
4247 sc->syninfo.div_min = 9;
4248 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4249 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4250 "div_min", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4251 &sc->syninfo.div_min, SYNAPTICS_SYSCTL_DIV_MIN,
4252 synaptics_sysctl, "I",
4253 "Divisor for fast movements");
4255 /* hw.psm.synaptics.div_max. */
4256 sc->syninfo.div_max = 17;
4257 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4258 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4259 "div_max", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4260 &sc->syninfo.div_max, SYNAPTICS_SYSCTL_DIV_MAX,
4261 synaptics_sysctl, "I",
4262 "Divisor for slow movements");
4264 /* hw.psm.synaptics.div_max_na. */
4265 sc->syninfo.div_max_na = 30;
4266 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4267 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4268 "div_max_na", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4269 &sc->syninfo.div_max_na, SYNAPTICS_SYSCTL_DIV_MAX_NA,
4270 synaptics_sysctl, "I",
4271 "Divisor with slow movements (inside the noisy area)");
4273 /* hw.psm.synaptics.div_len. */
4274 sc->syninfo.div_len = 100;
4275 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4276 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4277 "div_len", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4278 &sc->syninfo.div_len, SYNAPTICS_SYSCTL_DIV_LEN,
4279 synaptics_sysctl, "I",
4280 "Length of segments where div_max starts to decrease");
4282 /* hw.psm.synaptics.tap_max_delta. */
4283 sc->syninfo.tap_max_delta = 80;
4284 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4285 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4286 "tap_max_delta", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4287 &sc->syninfo.tap_max_delta, SYNAPTICS_SYSCTL_TAP_MAX_DELTA,
4288 synaptics_sysctl, "I",
4289 "Length of segments above which a tap is ignored");
4291 /* hw.psm.synaptics.tap_min_queue. */
4292 sc->syninfo.tap_min_queue = 2;
4293 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4294 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4295 "tap_min_queue", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4296 &sc->syninfo.tap_min_queue, SYNAPTICS_SYSCTL_TAP_MIN_QUEUE,
4297 synaptics_sysctl, "I",
4298 "Number of packets required to consider a tap");
4300 /* hw.psm.synaptics.taphold_timeout. */
4301 sc->synaction.in_taphold = 0;
4302 sc->syninfo.taphold_timeout = tap_timeout;
4303 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4304 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4305 "taphold_timeout", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4306 &sc->syninfo.taphold_timeout, SYNAPTICS_SYSCTL_TAPHOLD_TIMEOUT,
4307 synaptics_sysctl, "I",
4308 "Maximum elapsed time between two taps to consider a tap-hold "
4311 /* hw.psm.synaptics.vscroll_hor_area. */
4312 sc->syninfo.vscroll_hor_area = 0; /* 1300 */
4313 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4314 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4315 "vscroll_hor_area", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4316 &sc->syninfo.vscroll_hor_area, SYNAPTICS_SYSCTL_VSCROLL_HOR_AREA,
4317 synaptics_sysctl, "I",
4318 "Area reserved for horizontal virtual scrolling");
4320 /* hw.psm.synaptics.vscroll_ver_area. */
4321 sc->syninfo.vscroll_ver_area = -600;
4322 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4323 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4324 "vscroll_ver_area", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4325 &sc->syninfo.vscroll_ver_area, SYNAPTICS_SYSCTL_VSCROLL_VER_AREA,
4326 synaptics_sysctl, "I",
4327 "Area reserved for vertical virtual scrolling");
4329 /* hw.psm.synaptics.vscroll_min_delta. */
4330 sc->syninfo.vscroll_min_delta = 50;
4331 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4332 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4333 "vscroll_min_delta", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4334 &sc->syninfo.vscroll_min_delta,
4335 SYNAPTICS_SYSCTL_VSCROLL_MIN_DELTA,
4336 synaptics_sysctl, "I",
4337 "Minimum movement to consider virtual scrolling");
4339 /* hw.psm.synaptics.vscroll_div_min. */
4340 sc->syninfo.vscroll_div_min = 100;
4341 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4342 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4343 "vscroll_div_min", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4344 &sc->syninfo.vscroll_div_min, SYNAPTICS_SYSCTL_VSCROLL_DIV_MIN,
4345 synaptics_sysctl, "I",
4346 "Divisor for fast scrolling");
4348 /* hw.psm.synaptics.vscroll_div_min. */
4349 sc->syninfo.vscroll_div_max = 150;
4350 SYSCTL_ADD_PROC(&sc->syninfo.sysctl_ctx,
4351 SYSCTL_CHILDREN(sc->syninfo.sysctl_tree), OID_AUTO,
4352 "vscroll_div_max", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4353 &sc->syninfo.vscroll_div_max, SYNAPTICS_SYSCTL_VSCROLL_DIV_MAX,
4354 synaptics_sysctl, "I",
4355 "Divisor for slow scrolling");
4359 enable_synaptics(KBDC kbdc, struct psm_softc *sc)
4361 synapticshw_t synhw;
4365 VLOG(3, (LOG_DEBUG, "synaptics: BEGIN init\n"));
4368 * Just to be on the safe side: this avoids troubles with
4369 * following mouse_ext_command() when the previous command
4370 * was PSMC_SET_RESOLUTION. Set Scaling has no effect on
4371 * Synaptics Touchpad behaviour.
4373 set_mouse_scaling(kbdc, 1);
4375 /* Identify the Touchpad version. */
4376 if (mouse_ext_command(kbdc, 0) == 0)
4378 if (get_mouse_status(kbdc, status, 0, 3) != 3)
4380 if (status[1] != 0x47)
4383 bzero(&synhw, sizeof(synhw));
4384 synhw.infoMinor = status[0];
4385 synhw.infoMajor = status[2] & 0x0f;
4388 printf("Synaptics Touchpad v%d.%d\n", synhw.infoMajor,
4391 if (synhw.infoMajor < 4) {
4392 printf(" Unsupported (pre-v4) Touchpad detected\n");
4396 /* Get the Touchpad model information. */
4397 if (mouse_ext_command(kbdc, 3) == 0)
4399 if (get_mouse_status(kbdc, status, 0, 3) != 3)
4401 if ((status[1] & 0x01) != 0) {
4402 printf(" Failed to read model information\n");
4406 synhw.infoRot180 = (status[0] & 0x80) != 0;
4407 synhw.infoPortrait = (status[0] & 0x40) != 0;
4408 synhw.infoSensor = status[0] & 0x3f;
4409 synhw.infoHardware = (status[1] & 0xfe) >> 1;
4410 synhw.infoNewAbs = (status[2] & 0x80) != 0;
4411 synhw.capPen = (status[2] & 0x40) != 0;
4412 synhw.infoSimplC = (status[2] & 0x20) != 0;
4413 synhw.infoGeometry = status[2] & 0x0f;
4416 printf(" Model information:\n");
4417 printf(" infoRot180: %d\n", synhw.infoRot180);
4418 printf(" infoPortrait: %d\n", synhw.infoPortrait);
4419 printf(" infoSensor: %d\n", synhw.infoSensor);
4420 printf(" infoHardware: %d\n", synhw.infoHardware);
4421 printf(" infoNewAbs: %d\n", synhw.infoNewAbs);
4422 printf(" capPen: %d\n", synhw.capPen);
4423 printf(" infoSimplC: %d\n", synhw.infoSimplC);
4424 printf(" infoGeometry: %d\n", synhw.infoGeometry);
4427 /* Read the extended capability bits. */
4428 if (mouse_ext_command(kbdc, 2) == 0)
4430 if (get_mouse_status(kbdc, status, 0, 3) != 3)
4432 if (!SYNAPTICS_VERSION_GE(synhw, 7, 5) && status[1] != 0x47) {
4433 printf(" Failed to read extended capability bits\n");
4437 /* Set the different capabilities when they exist. */
4439 synhw.capExtended = (status[0] & 0x80) != 0;
4440 if (synhw.capExtended) {
4441 synhw.capPassthrough = (status[2] & 0x80) != 0;
4442 synhw.capSleep = (status[2] & 0x10) != 0;
4443 synhw.capFourButtons = (status[2] & 0x08) != 0;
4444 synhw.capMultiFinger = (status[2] & 0x02) != 0;
4445 synhw.capPalmDetect = (status[2] & 0x01) != 0;
4448 printf(" Extended capabilities:\n");
4449 printf(" capExtended: %d\n", synhw.capExtended);
4450 printf(" capPassthrough: %d\n", synhw.capPassthrough);
4451 printf(" capSleep: %d\n", synhw.capSleep);
4452 printf(" capFourButtons: %d\n", synhw.capFourButtons);
4453 printf(" capMultiFinger: %d\n", synhw.capMultiFinger);
4454 printf(" capPalmDetect: %d\n", synhw.capPalmDetect);
4458 * If we have bits set in status[0] & 0x70, then we can load
4459 * more information about buttons using query 0x09.
4461 if ((status[0] & 0x70) != 0) {
4462 if (mouse_ext_command(kbdc, 0x09) == 0)
4464 if (get_mouse_status(kbdc, status, 0, 3) != 3)
4466 buttons = (status[1] & 0xf0) >> 4;
4468 buttons = synhw.capFourButtons ? 1 : 0;
4471 if (synhw.capExtended)
4472 printf(" Additional Buttons: %d\n", buttons);
4474 printf(" No extended capabilities\n");
4478 * Read the mode byte.
4480 * XXX: Note the Synaptics documentation also defines the first
4481 * byte of the response to this query to be a constant 0x3b, this
4482 * does not appear to be true for Touchpads with guest devices.
4484 if (mouse_ext_command(kbdc, 1) == 0)
4486 if (get_mouse_status(kbdc, status, 0, 3) != 3)
4488 if (!SYNAPTICS_VERSION_GE(synhw, 7, 5) && status[1] != 0x47) {
4489 printf(" Failed to read mode byte\n");
4495 if (!synaptics_support)
4498 /* Set the mode byte; request wmode where available. */
4499 mouse_ext_command(kbdc, synhw.capExtended ? 0xc1 : 0xc0);
4501 /* "Commit" the Set Mode Byte command sent above. */
4502 set_mouse_sampling_rate(kbdc, 20);
4505 VLOG(3, (LOG_DEBUG, "synaptics: END init (%d buttons)\n", buttons));
4508 /* Create sysctl tree. */
4509 synaptics_sysctl_create_tree(sc);
4511 sc->hw.buttons = buttons;
4517 /* IBM/Lenovo TrackPoint */
4519 trackpoint_command(KBDC kbdc, int cmd, int loc, int val)
4521 const int seq[] = { 0xe2, cmd, loc, val };
4524 for (i = 0; i < nitems(seq); i++)
4525 if (send_aux_command(kbdc, seq[i]) != PSM_ACK)
4530 #define PSM_TPINFO(x) offsetof(struct psm_softc, tpinfo.x)
4536 trackpoint_sysctl(SYSCTL_HANDLER_ARGS)
4538 static const int data[][3] = {
4539 { 0x00, 0x4a, PSM_TPINFO(sensitivity) },
4540 { 0x00, 0x4d, PSM_TPINFO(inertia) },
4541 { 0x00, 0x60, PSM_TPINFO(uplateau) },
4542 { 0x00, 0x57, PSM_TPINFO(reach) },
4543 { 0x00, 0x58, PSM_TPINFO(draghys) },
4544 { 0x00, 0x59, PSM_TPINFO(mindrag) },
4545 { 0x00, 0x5a, PSM_TPINFO(upthresh) },
4546 { 0x00, 0x5c, PSM_TPINFO(threshold) },
4547 { 0x00, 0x5d, PSM_TPINFO(jenks) },
4548 { 0x00, 0x5e, PSM_TPINFO(ztime) },
4549 { 0x01, 0x2c, PSM_TPINFO(pts) },
4550 { 0x08, 0x2d, PSM_TPINFO(skipback) }
4552 struct psm_softc *sc;
4553 int error, newval, *oldvalp;
4556 if (arg1 == NULL || arg2 < 0 || arg2 >= nitems(data))
4560 oldvalp = (int *)((intptr_t)sc + tp[TPINFO]);
4562 error = sysctl_handle_int(oidp, &newval, 0, req);
4565 if (newval == *oldvalp)
4567 if (newval < 0 || newval > (tp[TPMASK] == 0 ? 255 : 1))
4569 error = trackpoint_command(sc->kbdc, tp[TPMASK] == 0 ? 0x81 : 0x47,
4570 tp[TPLOC], tp[TPMASK] == 0 ? newval : tp[TPMASK]);
4579 trackpoint_sysctl_create_tree(struct psm_softc *sc)
4582 if (sc->tpinfo.sysctl_tree != NULL)
4585 /* Attach extra trackpoint sysctl nodes under hw.psm.trackpoint */
4586 sysctl_ctx_init(&sc->tpinfo.sysctl_ctx);
4587 sc->tpinfo.sysctl_tree = SYSCTL_ADD_NODE(&sc->tpinfo.sysctl_ctx,
4588 SYSCTL_STATIC_CHILDREN(_hw_psm), OID_AUTO, "trackpoint", CTLFLAG_RD,
4589 0, "IBM/Lenovo TrackPoint");
4591 /* hw.psm.trackpoint.sensitivity */
4592 sc->tpinfo.sensitivity = 0x64;
4593 SYSCTL_ADD_PROC(&sc->tpinfo.sysctl_ctx,
4594 SYSCTL_CHILDREN(sc->tpinfo.sysctl_tree), OID_AUTO,
4595 "sensitivity", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4596 sc, TRACKPOINT_SYSCTL_SENSITIVITY,
4597 trackpoint_sysctl, "I",
4600 /* hw.psm.trackpoint.negative_inertia */
4601 sc->tpinfo.inertia = 0x06;
4602 SYSCTL_ADD_PROC(&sc->tpinfo.sysctl_ctx,
4603 SYSCTL_CHILDREN(sc->tpinfo.sysctl_tree), OID_AUTO,
4604 "negative_inertia", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4605 sc, TRACKPOINT_SYSCTL_NEGATIVE_INERTIA,
4606 trackpoint_sysctl, "I",
4607 "Negative inertia factor");
4609 /* hw.psm.trackpoint.upper_plateau */
4610 sc->tpinfo.uplateau = 0x61;
4611 SYSCTL_ADD_PROC(&sc->tpinfo.sysctl_ctx,
4612 SYSCTL_CHILDREN(sc->tpinfo.sysctl_tree), OID_AUTO,
4613 "upper_plateau", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4614 sc, TRACKPOINT_SYSCTL_UPPER_PLATEAU,
4615 trackpoint_sysctl, "I",
4616 "Transfer function upper plateau speed");
4618 /* hw.psm.trackpoint.backup_range */
4619 sc->tpinfo.reach = 0x0a;
4620 SYSCTL_ADD_PROC(&sc->tpinfo.sysctl_ctx,
4621 SYSCTL_CHILDREN(sc->tpinfo.sysctl_tree), OID_AUTO,
4622 "backup_range", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4623 sc, TRACKPOINT_SYSCTL_BACKUP_RANGE,
4624 trackpoint_sysctl, "I",
4627 /* hw.psm.trackpoint.drag_hysteresis */
4628 sc->tpinfo.draghys = 0xff;
4629 SYSCTL_ADD_PROC(&sc->tpinfo.sysctl_ctx,
4630 SYSCTL_CHILDREN(sc->tpinfo.sysctl_tree), OID_AUTO,
4631 "drag_hysteresis", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4632 sc, TRACKPOINT_SYSCTL_DRAG_HYSTERESIS,
4633 trackpoint_sysctl, "I",
4636 /* hw.psm.trackpoint.minimum_drag */
4637 sc->tpinfo.mindrag = 0x14;
4638 SYSCTL_ADD_PROC(&sc->tpinfo.sysctl_ctx,
4639 SYSCTL_CHILDREN(sc->tpinfo.sysctl_tree), OID_AUTO,
4640 "minimum_drag", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4641 sc, TRACKPOINT_SYSCTL_MINIMUM_DRAG,
4642 trackpoint_sysctl, "I",
4645 /* hw.psm.trackpoint.up_threshold */
4646 sc->tpinfo.upthresh = 0xff;
4647 SYSCTL_ADD_PROC(&sc->tpinfo.sysctl_ctx,
4648 SYSCTL_CHILDREN(sc->tpinfo.sysctl_tree), OID_AUTO,
4649 "up_threshold", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4650 sc, TRACKPOINT_SYSCTL_UP_THRESHOLD,
4651 trackpoint_sysctl, "I",
4652 "Up threshold for release");
4654 /* hw.psm.trackpoint.threshold */
4655 sc->tpinfo.threshold = 0x08;
4656 SYSCTL_ADD_PROC(&sc->tpinfo.sysctl_ctx,
4657 SYSCTL_CHILDREN(sc->tpinfo.sysctl_tree), OID_AUTO,
4658 "threshold", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4659 sc, TRACKPOINT_SYSCTL_THRESHOLD,
4660 trackpoint_sysctl, "I",
4663 /* hw.psm.trackpoint.jenks_curvature */
4664 sc->tpinfo.jenks = 0x87;
4665 SYSCTL_ADD_PROC(&sc->tpinfo.sysctl_ctx,
4666 SYSCTL_CHILDREN(sc->tpinfo.sysctl_tree), OID_AUTO,
4667 "jenks_curvature", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4668 sc, TRACKPOINT_SYSCTL_JENKS_CURVATURE,
4669 trackpoint_sysctl, "I",
4672 /* hw.psm.trackpoint.z_time */
4673 sc->tpinfo.ztime = 0x26;
4674 SYSCTL_ADD_PROC(&sc->tpinfo.sysctl_ctx,
4675 SYSCTL_CHILDREN(sc->tpinfo.sysctl_tree), OID_AUTO,
4676 "z_time", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4677 sc, TRACKPOINT_SYSCTL_Z_TIME,
4678 trackpoint_sysctl, "I",
4681 /* hw.psm.trackpoint.press_to_select */
4682 sc->tpinfo.pts = 0x00;
4683 SYSCTL_ADD_PROC(&sc->tpinfo.sysctl_ctx,
4684 SYSCTL_CHILDREN(sc->tpinfo.sysctl_tree), OID_AUTO,
4685 "press_to_select", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4686 sc, TRACKPOINT_SYSCTL_PRESS_TO_SELECT,
4687 trackpoint_sysctl, "I",
4690 /* hw.psm.trackpoint.skip_backups */
4691 sc->tpinfo.skipback = 0x00;
4692 SYSCTL_ADD_PROC(&sc->tpinfo.sysctl_ctx,
4693 SYSCTL_CHILDREN(sc->tpinfo.sysctl_tree), OID_AUTO,
4694 "skip_backups", CTLTYPE_INT|CTLFLAG_RW|CTLFLAG_ANYBODY,
4695 sc, TRACKPOINT_SYSCTL_SKIP_BACKUPS,
4696 trackpoint_sysctl, "I",
4697 "Skip backups from drags");
4701 enable_trackpoint(KBDC kbdc, struct psm_softc *sc)
4707 if (send_aux_command(kbdc, 0xe1) != PSM_ACK ||
4708 read_aux_data(kbdc) != 0x01)
4710 id = read_aux_data(kbdc);
4715 if (!trackpoint_support)
4719 /* Create sysctl tree. */
4720 trackpoint_sysctl_create_tree(sc);
4722 trackpoint_command(kbdc, 0x81, 0x4a, sc->tpinfo.sensitivity);
4723 trackpoint_command(kbdc, 0x81, 0x4d, sc->tpinfo.inertia);
4724 trackpoint_command(kbdc, 0x81, 0x60, sc->tpinfo.uplateau);
4725 trackpoint_command(kbdc, 0x81, 0x57, sc->tpinfo.reach);
4726 trackpoint_command(kbdc, 0x81, 0x58, sc->tpinfo.draghys);
4727 trackpoint_command(kbdc, 0x81, 0x59, sc->tpinfo.mindrag);
4728 trackpoint_command(kbdc, 0x81, 0x5a, sc->tpinfo.upthresh);
4729 trackpoint_command(kbdc, 0x81, 0x5c, sc->tpinfo.threshold);
4730 trackpoint_command(kbdc, 0x81, 0x5d, sc->tpinfo.jenks);
4731 trackpoint_command(kbdc, 0x81, 0x5e, sc->tpinfo.ztime);
4732 if (sc->tpinfo.pts == 0x01)
4733 trackpoint_command(kbdc, 0x47, 0x2c, 0x01);
4734 if (sc->tpinfo.skipback == 0x01)
4735 trackpoint_command(kbdc, 0x47, 0x2d, 0x08);
4744 /* Interlink electronics VersaPad */
4746 enable_versapad(KBDC kbdc, struct psm_softc *sc)
4750 set_mouse_resolution(kbdc, PSMD_RES_MEDIUM_HIGH); /* set res. 2 */
4751 set_mouse_sampling_rate(kbdc, 100); /* set rate 100 */
4752 set_mouse_scaling(kbdc, 1); /* set scale 1:1 */
4753 set_mouse_scaling(kbdc, 1); /* set scale 1:1 */
4754 set_mouse_scaling(kbdc, 1); /* set scale 1:1 */
4755 set_mouse_scaling(kbdc, 1); /* set scale 1:1 */
4756 if (get_mouse_status(kbdc, data, 0, 3) < 3) /* get status */
4758 if (data[2] != 0xa || data[1] != 0 ) /* rate == 0xa && res. == 0 */
4760 set_mouse_scaling(kbdc, 1); /* set scale 1:1 */
4762 return (TRUE); /* PS/2 absolute mode */
4766 * Return true if 'now' is earlier than (start + (secs.usecs)).
4767 * Now may be NULL and the function will fetch the current time from
4768 * getmicrouptime(), or a cached 'now' can be passed in.
4769 * All values should be numbers derived from getmicrouptime().
4772 timeelapsed(start, secs, usecs, now)
4773 const struct timeval *start, *now;
4776 struct timeval snow, tv;
4778 /* if there is no 'now' passed in, the get it as a convience. */
4780 getmicrouptime(&snow);
4786 timevaladd(&tv, start);
4787 return (timevalcmp(&tv, now, <));
4791 psmresume(device_t dev)
4793 struct psm_softc *sc = device_get_softc(dev);
4794 int unit = device_get_unit(dev);
4797 VLOG(2, (LOG_NOTICE, "psm%d: system resume hook called.\n", unit));
4800 (PSM_CONFIG_HOOKRESUME | PSM_CONFIG_INITAFTERSUSPEND)) == 0)
4803 err = reinitialize(sc, sc->config & PSM_CONFIG_INITAFTERSUSPEND);
4805 if ((sc->state & PSM_ASLP) && !(sc->state & PSM_VALID)) {
4807 * Release the blocked process; it must be notified that
4808 * the device cannot be accessed anymore.
4810 sc->state &= ~PSM_ASLP;
4814 VLOG(2, (LOG_DEBUG, "psm%d: system resume hook exiting.\n", unit));
4819 DRIVER_MODULE(psm, atkbdc, psm_driver, psm_devclass, 0, 0);
4824 * This sucks up assignments from PNPBIOS and ACPI.
4828 * When the PS/2 mouse device is reported by ACPI or PnP BIOS, it may
4829 * appear BEFORE the AT keyboard controller. As the PS/2 mouse device
4830 * can be probed and attached only after the AT keyboard controller is
4831 * attached, we shall quietly reserve the IRQ resource for later use.
4832 * If the PS/2 mouse device is reported to us AFTER the keyboard controller,
4833 * copy the IRQ resource to the PS/2 mouse device instance hanging
4834 * under the keyboard controller, then probe and attach it.
4837 static devclass_t psmcpnp_devclass;
4839 static device_probe_t psmcpnp_probe;
4840 static device_attach_t psmcpnp_attach;
4842 static device_method_t psmcpnp_methods[] = {
4843 DEVMETHOD(device_probe, psmcpnp_probe),
4844 DEVMETHOD(device_attach, psmcpnp_attach),
4849 static driver_t psmcpnp_driver = {
4850 PSMCPNP_DRIVER_NAME,
4855 static struct isa_pnp_id psmcpnp_ids[] = {
4856 { 0x030fd041, "PS/2 mouse port" }, /* PNP0F03 */
4857 { 0x0e0fd041, "PS/2 mouse port" }, /* PNP0F0E */
4858 { 0x120fd041, "PS/2 mouse port" }, /* PNP0F12 */
4859 { 0x130fd041, "PS/2 mouse port" }, /* PNP0F13 */
4860 { 0x1303d041, "PS/2 port" }, /* PNP0313, XXX */
4861 { 0x02002e4f, "Dell PS/2 mouse port" }, /* Lat. X200, Dell */
4862 { 0x0002a906, "ALPS Glide Point" }, /* ALPS Glide Point */
4863 { 0x80374d24, "IBM PS/2 mouse port" }, /* IBM3780, ThinkPad */
4864 { 0x81374d24, "IBM PS/2 mouse port" }, /* IBM3781, ThinkPad */
4865 { 0x0190d94d, "SONY VAIO PS/2 mouse port"}, /* SNY9001, Vaio */
4866 { 0x0290d94d, "SONY VAIO PS/2 mouse port"}, /* SNY9002, Vaio */
4867 { 0x0390d94d, "SONY VAIO PS/2 mouse port"}, /* SNY9003, Vaio */
4868 { 0x0490d94d, "SONY VAIO PS/2 mouse port"}, /* SNY9004, Vaio */
4873 create_a_copy(device_t atkbdc, device_t me)
4878 /* find the PS/2 mouse device instance under the keyboard controller */
4879 psm = device_find_child(atkbdc, PSM_DRIVER_NAME,
4880 device_get_unit(atkbdc));
4883 if (device_get_state(psm) != DS_NOTPRESENT)
4886 /* move our resource to the found device */
4887 irq = bus_get_resource_start(me, SYS_RES_IRQ, 0);
4888 bus_delete_resource(me, SYS_RES_IRQ, 0);
4889 bus_set_resource(psm, SYS_RES_IRQ, KBDC_RID_AUX, irq, 1);
4891 /* ...then probe and attach it */
4892 return (device_probe_and_attach(psm));
4896 psmcpnp_probe(device_t dev)
4898 struct resource *res;
4902 if (ISA_PNP_PROBE(device_get_parent(dev), dev, psmcpnp_ids))
4906 * The PnP BIOS and ACPI are supposed to assign an IRQ (12)
4907 * to the PS/2 mouse device node. But, some buggy PnP BIOS
4908 * declares the PS/2 mouse device node without an IRQ resource!
4909 * If this happens, we shall refer to device hints.
4910 * If we still don't find it there, use a hardcoded value... XXX
4913 irq = bus_get_resource_start(dev, SYS_RES_IRQ, rid);
4915 if (resource_long_value(PSM_DRIVER_NAME,
4916 device_get_unit(dev),"irq", &irq) != 0)
4918 device_printf(dev, "irq resource info is missing; "
4919 "assuming irq %ld\n", irq);
4920 bus_set_resource(dev, SYS_RES_IRQ, rid, irq, 1);
4922 res = bus_alloc_resource_any(dev, SYS_RES_IRQ, &rid, 0);
4923 bus_release_resource(dev, SYS_RES_IRQ, rid, res);
4929 return ((res == NULL) ? ENXIO : 0);
4933 psmcpnp_attach(device_t dev)
4937 /* find the keyboard controller, which may be on acpi* or isa* bus */
4938 atkbdc = devclass_get_device(devclass_find(ATKBDC_DRIVER_NAME),
4939 device_get_unit(dev));
4940 if ((atkbdc != NULL) && (device_get_state(atkbdc) == DS_ATTACHED))
4941 create_a_copy(atkbdc, dev);
4946 DRIVER_MODULE(psmcpnp, isa, psmcpnp_driver, psmcpnp_devclass, 0, 0);
4947 DRIVER_MODULE(psmcpnp, acpi, psmcpnp_driver, psmcpnp_devclass, 0, 0);
4949 #endif /* DEV_ISA */