2 * Copyright (c) 2008 Weongyo Jeong <weongyo@freebsd.org>
3 * Copyright (c) 2007 Marvell Semiconductor, Inc.
4 * Copyright (c) 2007 Sam Leffler, Errno Consulting
7 * Redistribution and use in source and binary forms, with or without
8 * modification, are permitted provided that the following conditions
10 * 1. Redistributions of source code must retain the above copyright
11 * notice, this list of conditions and the following disclaimer,
12 * without modification.
13 * 2. Redistributions in binary form must reproduce at minimum a disclaimer
14 * similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
15 * redistribution must be conditioned upon including a substantially
16 * similar Disclaimer requirement for further binary redistribution.
19 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
20 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
21 * LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
22 * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
23 * THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
24 * OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
25 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
26 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
27 * IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
28 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
29 * THE POSSIBILITY OF SUCH DAMAGES.
32 #include <sys/cdefs.h>
34 __FBSDID("$FreeBSD$");
39 #include <sys/param.h>
40 #include <sys/endian.h>
41 #include <sys/kernel.h>
42 #include <sys/socket.h>
43 #include <sys/sockio.h>
44 #include <sys/sysctl.h>
45 #include <sys/taskqueue.h>
47 #include <machine/bus.h>
51 #include <net/if_dl.h>
52 #include <net/if_media.h>
53 #include <net/if_types.h>
54 #include <net/ethernet.h>
56 #include <net80211/ieee80211_var.h>
57 #include <net80211/ieee80211_regdomain.h>
61 #include <dev/malo/if_malo.h>
63 SYSCTL_NODE(_hw, OID_AUTO, malo, CTLFLAG_RD, 0,
64 "Marvell 88w8335 driver parameters");
66 static int malo_txcoalesce = 8; /* # tx pkts to q before poking f/w*/
67 SYSCTL_INT(_hw_malo, OID_AUTO, txcoalesce, CTLFLAG_RW, &malo_txcoalesce,
68 0, "tx buffers to send at once");
69 TUNABLE_INT("hw.malo.txcoalesce", &malo_txcoalesce);
70 static int malo_rxbuf = MALO_RXBUF; /* # rx buffers to allocate */
71 SYSCTL_INT(_hw_malo, OID_AUTO, rxbuf, CTLFLAG_RW, &malo_rxbuf,
72 0, "rx buffers allocated");
73 TUNABLE_INT("hw.malo.rxbuf", &malo_rxbuf);
74 static int malo_rxquota = MALO_RXBUF; /* # max buffers to process */
75 SYSCTL_INT(_hw_malo, OID_AUTO, rxquota, CTLFLAG_RW, &malo_rxquota,
76 0, "max rx buffers to process per interrupt");
77 TUNABLE_INT("hw.malo.rxquota", &malo_rxquota);
78 static int malo_txbuf = MALO_TXBUF; /* # tx buffers to allocate */
79 SYSCTL_INT(_hw_malo, OID_AUTO, txbuf, CTLFLAG_RW, &malo_txbuf,
80 0, "tx buffers allocated");
81 TUNABLE_INT("hw.malo.txbuf", &malo_txbuf);
84 static int malo_debug = 0;
85 SYSCTL_INT(_hw_malo, OID_AUTO, debug, CTLFLAG_RW, &malo_debug,
86 0, "control debugging printfs");
87 TUNABLE_INT("hw.malo.debug", &malo_debug);
89 MALO_DEBUG_XMIT = 0x00000001, /* basic xmit operation */
90 MALO_DEBUG_XMIT_DESC = 0x00000002, /* xmit descriptors */
91 MALO_DEBUG_RECV = 0x00000004, /* basic recv operation */
92 MALO_DEBUG_RECV_DESC = 0x00000008, /* recv descriptors */
93 MALO_DEBUG_RESET = 0x00000010, /* reset processing */
94 MALO_DEBUG_INTR = 0x00000040, /* ISR */
95 MALO_DEBUG_TX_PROC = 0x00000080, /* tx ISR proc */
96 MALO_DEBUG_RX_PROC = 0x00000100, /* rx ISR proc */
97 MALO_DEBUG_STATE = 0x00000400, /* 802.11 state transitions */
98 MALO_DEBUG_NODE = 0x00000800, /* node management */
99 MALO_DEBUG_RECV_ALL = 0x00001000, /* trace all frames (beacons) */
100 MALO_DEBUG_FW = 0x00008000, /* firmware */
101 MALO_DEBUG_ANY = 0xffffffff
103 #define IS_BEACON(wh) \
104 ((wh->i_fc[0] & (IEEE80211_FC0_TYPE_MASK | \
105 IEEE80211_FC0_SUBTYPE_MASK)) == \
106 (IEEE80211_FC0_TYPE_MGT|IEEE80211_FC0_SUBTYPE_BEACON))
107 #define IFF_DUMPPKTS_RECV(sc, wh) \
108 (((sc->malo_debug & MALO_DEBUG_RECV) && \
109 ((sc->malo_debug & MALO_DEBUG_RECV_ALL) || !IS_BEACON(wh))) || \
110 (sc->malo_ifp->if_flags & (IFF_DEBUG|IFF_LINK2)) == \
111 (IFF_DEBUG|IFF_LINK2))
112 #define IFF_DUMPPKTS_XMIT(sc) \
113 ((sc->malo_debug & MALO_DEBUG_XMIT) || \
114 (sc->malo_ifp->if_flags & (IFF_DEBUG | IFF_LINK2)) == \
115 (IFF_DEBUG | IFF_LINK2))
116 #define DPRINTF(sc, m, fmt, ...) do { \
117 if (sc->malo_debug & (m)) \
118 printf(fmt, __VA_ARGS__); \
121 #define DPRINTF(sc, m, fmt, ...) do { \
126 static MALLOC_DEFINE(M_MALODEV, "malodev", "malo driver dma buffers");
128 static struct ieee80211vap *malo_vap_create(struct ieee80211com *,
129 const char [IFNAMSIZ], int, enum ieee80211_opmode, int,
130 const uint8_t [IEEE80211_ADDR_LEN],
131 const uint8_t [IEEE80211_ADDR_LEN]);
132 static void malo_vap_delete(struct ieee80211vap *);
133 static int malo_dma_setup(struct malo_softc *);
134 static int malo_setup_hwdma(struct malo_softc *);
135 static void malo_txq_init(struct malo_softc *, struct malo_txq *, int);
136 static void malo_tx_cleanupq(struct malo_softc *, struct malo_txq *);
137 static void malo_start(struct ifnet *);
138 static void malo_watchdog(void *);
139 static int malo_ioctl(struct ifnet *, u_long, caddr_t);
140 static void malo_updateslot(struct ifnet *);
141 static int malo_newstate(struct ieee80211vap *, enum ieee80211_state, int);
142 static void malo_scan_start(struct ieee80211com *);
143 static void malo_scan_end(struct ieee80211com *);
144 static void malo_set_channel(struct ieee80211com *);
145 static int malo_raw_xmit(struct ieee80211_node *, struct mbuf *,
146 const struct ieee80211_bpf_params *);
147 static void malo_sysctlattach(struct malo_softc *);
148 static void malo_announce(struct malo_softc *);
149 static void malo_dma_cleanup(struct malo_softc *);
150 static void malo_stop_locked(struct ifnet *, int);
151 static int malo_chan_set(struct malo_softc *, struct ieee80211_channel *);
152 static int malo_mode_init(struct malo_softc *);
153 static void malo_tx_proc(void *, int);
154 static void malo_rx_proc(void *, int);
155 static void malo_init(void *);
158 * Read/Write shorthands for accesses to BAR 0. Note that all BAR 1
159 * operations are done in the "hal" except getting H/W MAC address at
160 * malo_attach and there should be no reference to them here.
163 malo_bar0_read4(struct malo_softc *sc, bus_size_t off)
165 return bus_space_read_4(sc->malo_io0t, sc->malo_io0h, off);
169 malo_bar0_write4(struct malo_softc *sc, bus_size_t off, uint32_t val)
171 DPRINTF(sc, MALO_DEBUG_FW, "%s: off 0x%jx val 0x%x\n",
172 __func__, (intmax_t)off, val);
174 bus_space_write_4(sc->malo_io0t, sc->malo_io0h, off, val);
178 malo_attach(uint16_t devid, struct malo_softc *sc)
181 struct ieee80211com *ic;
186 ifp = sc->malo_ifp = if_alloc(IFT_IEEE80211);
188 device_printf(sc->malo_dev, "can not if_alloc()\n");
194 callout_init_mtx(&sc->malo_watchdog_timer, &sc->malo_mtx, 0);
196 /* set these up early for if_printf use */
197 if_initname(ifp, device_get_name(sc->malo_dev),
198 device_get_unit(sc->malo_dev));
200 mh = malo_hal_attach(sc->malo_dev, devid,
201 sc->malo_io1h, sc->malo_io1t, sc->malo_dmat);
203 if_printf(ifp, "unable to attach HAL\n");
210 * Load firmware so we can get setup. We arbitrarily pick station
211 * firmware; we'll re-load firmware as needed so setting up
212 * the wrong mode isn't a big deal.
214 error = malo_hal_fwload(mh, "malo8335-h", "malo8335-m");
216 if_printf(ifp, "unable to setup firmware\n");
219 /* XXX gethwspecs() extracts correct informations? not maybe! */
220 error = malo_hal_gethwspecs(mh, &sc->malo_hwspecs);
222 if_printf(ifp, "unable to fetch h/w specs\n");
226 DPRINTF(sc, MALO_DEBUG_FW,
227 "malo_hal_gethwspecs: hwversion 0x%x hostif 0x%x"
228 "maxnum_wcb 0x%x maxnum_mcaddr 0x%x maxnum_tx_wcb 0x%x"
229 "regioncode 0x%x num_antenna 0x%x fw_releasenum 0x%x"
230 "wcbbase0 0x%x rxdesc_read 0x%x rxdesc_write 0x%x"
231 "ul_fw_awakecookie 0x%x w[4] = %x %x %x %x",
232 sc->malo_hwspecs.hwversion,
233 sc->malo_hwspecs.hostinterface, sc->malo_hwspecs.maxnum_wcb,
234 sc->malo_hwspecs.maxnum_mcaddr, sc->malo_hwspecs.maxnum_tx_wcb,
235 sc->malo_hwspecs.regioncode, sc->malo_hwspecs.num_antenna,
236 sc->malo_hwspecs.fw_releasenum, sc->malo_hwspecs.wcbbase0,
237 sc->malo_hwspecs.rxdesc_read, sc->malo_hwspecs.rxdesc_write,
238 sc->malo_hwspecs.ul_fw_awakecookie,
239 sc->malo_hwspecs.wcbbase[0], sc->malo_hwspecs.wcbbase[1],
240 sc->malo_hwspecs.wcbbase[2], sc->malo_hwspecs.wcbbase[3]);
242 /* NB: firmware looks that it does not export regdomain info API. */
244 setbit(&bands, IEEE80211_MODE_11B);
245 setbit(&bands, IEEE80211_MODE_11G);
246 ieee80211_init_channels(ic, NULL, &bands);
248 sc->malo_txantenna = 0x2; /* h/w default */
249 sc->malo_rxantenna = 0xffff; /* h/w default */
252 * Allocate tx + rx descriptors and populate the lists.
253 * We immediately push the information to the firmware
254 * as otherwise it gets upset.
256 error = malo_dma_setup(sc);
258 if_printf(ifp, "failed to setup descriptors: %d\n", error);
261 error = malo_setup_hwdma(sc); /* push to firmware */
262 if (error != 0) /* NB: malo_setupdma prints msg */
265 sc->malo_tq = taskqueue_create_fast("malo_taskq", M_NOWAIT,
266 taskqueue_thread_enqueue, &sc->malo_tq);
267 taskqueue_start_threads(&sc->malo_tq, 1, PI_NET,
268 "%s taskq", ifp->if_xname);
270 TASK_INIT(&sc->malo_rxtask, 0, malo_rx_proc, sc);
271 TASK_INIT(&sc->malo_txtask, 0, malo_tx_proc, sc);
274 ifp->if_flags = IFF_SIMPLEX | IFF_BROADCAST | IFF_MULTICAST;
275 ifp->if_start = malo_start;
276 ifp->if_ioctl = malo_ioctl;
277 ifp->if_init = malo_init;
278 IFQ_SET_MAXLEN(&ifp->if_snd, ifqmaxlen);
279 ifp->if_snd.ifq_drv_maxlen = ifqmaxlen;
280 IFQ_SET_READY(&ifp->if_snd);
283 /* XXX not right but it's not used anywhere important */
284 ic->ic_phytype = IEEE80211_T_OFDM;
285 ic->ic_opmode = IEEE80211_M_STA;
287 IEEE80211_C_STA /* station mode supported */
288 | IEEE80211_C_BGSCAN /* capable of bg scanning */
289 | IEEE80211_C_MONITOR /* monitor mode */
290 | IEEE80211_C_SHPREAMBLE /* short preamble supported */
291 | IEEE80211_C_SHSLOT /* short slot time supported */
292 | IEEE80211_C_TXPMGT /* capable of txpow mgt */
293 | IEEE80211_C_WPA /* capable of WPA1+WPA2 */
297 * Transmit requires space in the packet for a special format transmit
298 * record and optional padding between this record and the payload.
299 * Ask the net80211 layer to arrange this when encapsulating
300 * packets so we can add it efficiently.
302 ic->ic_headroom = sizeof(struct malo_txrec) -
303 sizeof(struct ieee80211_frame);
305 /* call MI attach routine. */
306 ieee80211_ifattach(ic, sc->malo_hwspecs.macaddr);
307 /* override default methods */
308 ic->ic_vap_create = malo_vap_create;
309 ic->ic_vap_delete = malo_vap_delete;
310 ic->ic_raw_xmit = malo_raw_xmit;
311 ic->ic_updateslot = malo_updateslot;
313 ic->ic_scan_start = malo_scan_start;
314 ic->ic_scan_end = malo_scan_end;
315 ic->ic_set_channel = malo_set_channel;
317 sc->malo_invalid = 0; /* ready to go, enable int handling */
319 ieee80211_radiotap_attach(ic,
320 &sc->malo_tx_th.wt_ihdr, sizeof(sc->malo_tx_th),
321 MALO_TX_RADIOTAP_PRESENT,
322 &sc->malo_rx_th.wr_ihdr, sizeof(sc->malo_rx_th),
323 MALO_RX_RADIOTAP_PRESENT);
326 * Setup dynamic sysctl's.
328 malo_sysctlattach(sc);
331 ieee80211_announce(ic);
336 malo_dma_cleanup(sc);
341 sc->malo_invalid = 1;
346 static struct ieee80211vap *
347 malo_vap_create(struct ieee80211com *ic, const char name[IFNAMSIZ], int unit,
348 enum ieee80211_opmode opmode, int flags,
349 const uint8_t bssid[IEEE80211_ADDR_LEN],
350 const uint8_t mac[IEEE80211_ADDR_LEN])
352 struct ifnet *ifp = ic->ic_ifp;
353 struct malo_vap *mvp;
354 struct ieee80211vap *vap;
356 if (!TAILQ_EMPTY(&ic->ic_vaps)) {
357 if_printf(ifp, "multiple vaps not supported\n");
361 case IEEE80211_M_STA:
362 if (opmode == IEEE80211_M_STA)
363 flags |= IEEE80211_CLONE_NOBEACONS;
365 case IEEE80211_M_MONITOR:
368 if_printf(ifp, "%s mode not supported\n",
369 ieee80211_opmode_name[opmode]);
370 return NULL; /* unsupported */
372 mvp = (struct malo_vap *) malloc(sizeof(struct malo_vap),
373 M_80211_VAP, M_NOWAIT | M_ZERO);
375 if_printf(ifp, "cannot allocate vap state block\n");
378 vap = &mvp->malo_vap;
379 ieee80211_vap_setup(ic, vap, name, unit, opmode, flags, bssid, mac);
381 /* override state transition machine */
382 mvp->malo_newstate = vap->iv_newstate;
383 vap->iv_newstate = malo_newstate;
386 ieee80211_vap_attach(vap,
387 ieee80211_media_change, ieee80211_media_status);
388 ic->ic_opmode = opmode;
393 malo_vap_delete(struct ieee80211vap *vap)
395 struct malo_vap *mvp = MALO_VAP(vap);
397 ieee80211_vap_detach(vap);
398 free(mvp, M_80211_VAP);
404 struct malo_softc *sc = arg;
405 struct malo_hal *mh = sc->malo_mh;
408 if (sc->malo_invalid) {
410 * The hardware is not ready/present, don't touch anything.
411 * Note this can happen early on if the IRQ is shared.
413 DPRINTF(sc, MALO_DEBUG_ANY, "%s: invalid; ignored\n", __func__);
414 return (FILTER_STRAY);
418 * Figure out the reason(s) for the interrupt.
420 malo_hal_getisr(mh, &status); /* NB: clears ISR too */
421 if (status == 0) /* must be a shared irq */
422 return (FILTER_STRAY);
424 DPRINTF(sc, MALO_DEBUG_INTR, "%s: status 0x%x imask 0x%x\n",
425 __func__, status, sc->malo_imask);
427 if (status & MALO_A2HRIC_BIT_RX_RDY)
428 taskqueue_enqueue_fast(sc->malo_tq, &sc->malo_rxtask);
429 if (status & MALO_A2HRIC_BIT_TX_DONE)
430 taskqueue_enqueue_fast(sc->malo_tq, &sc->malo_txtask);
431 if (status & MALO_A2HRIC_BIT_OPC_DONE)
432 malo_hal_cmddone(mh);
433 if (status & MALO_A2HRIC_BIT_MAC_EVENT)
435 if (status & MALO_A2HRIC_BIT_RX_PROBLEM)
437 if (status & MALO_A2HRIC_BIT_ICV_ERROR) {
439 sc->malo_stats.mst_rx_badtkipicv++;
442 if (((status | sc->malo_imask) ^ sc->malo_imask) != 0)
443 DPRINTF(sc, MALO_DEBUG_INTR,
444 "%s: can't handle interrupt status 0x%x\n",
447 return (FILTER_HANDLED);
451 malo_load_cb(void *arg, bus_dma_segment_t *segs, int nsegs, int error)
453 bus_addr_t *paddr = (bus_addr_t*) arg;
455 KASSERT(error == 0, ("error %u on bus_dma callback", error));
457 *paddr = segs->ds_addr;
461 malo_desc_setup(struct malo_softc *sc, const char *name,
462 struct malo_descdma *dd,
463 int nbuf, size_t bufsize, int ndesc, size_t descsize)
466 struct ifnet *ifp = sc->malo_ifp;
469 DPRINTF(sc, MALO_DEBUG_RESET,
470 "%s: %s DMA: %u bufs (%ju) %u desc/buf (%ju)\n",
471 __func__, name, nbuf, (uintmax_t) bufsize,
472 ndesc, (uintmax_t) descsize);
475 dd->dd_desc_len = nbuf * ndesc * descsize;
478 * Setup DMA descriptor area.
480 error = bus_dma_tag_create(bus_get_dma_tag(sc->malo_dev),/* parent */
481 PAGE_SIZE, 0, /* alignment, bounds */
482 BUS_SPACE_MAXADDR_32BIT, /* lowaddr */
483 BUS_SPACE_MAXADDR, /* highaddr */
484 NULL, NULL, /* filter, filterarg */
485 dd->dd_desc_len, /* maxsize */
487 dd->dd_desc_len, /* maxsegsize */
488 BUS_DMA_ALLOCNOW, /* flags */
493 if_printf(ifp, "cannot allocate %s DMA tag\n", dd->dd_name);
497 /* allocate descriptors */
498 error = bus_dmamap_create(dd->dd_dmat, BUS_DMA_NOWAIT, &dd->dd_dmamap);
500 if_printf(ifp, "unable to create dmamap for %s descriptors, "
501 "error %u\n", dd->dd_name, error);
505 error = bus_dmamem_alloc(dd->dd_dmat, (void**) &dd->dd_desc,
506 BUS_DMA_NOWAIT | BUS_DMA_COHERENT, &dd->dd_dmamap);
508 if_printf(ifp, "unable to alloc memory for %u %s descriptors, "
509 "error %u\n", nbuf * ndesc, dd->dd_name, error);
513 error = bus_dmamap_load(dd->dd_dmat, dd->dd_dmamap,
514 dd->dd_desc, dd->dd_desc_len,
515 malo_load_cb, &dd->dd_desc_paddr, BUS_DMA_NOWAIT);
517 if_printf(ifp, "unable to map %s descriptors, error %u\n",
523 memset(ds, 0, dd->dd_desc_len);
524 DPRINTF(sc, MALO_DEBUG_RESET, "%s: %s DMA map: %p (%lu) -> %p (%lu)\n",
525 __func__, dd->dd_name, ds, (u_long) dd->dd_desc_len,
526 (caddr_t) dd->dd_desc_paddr, /*XXX*/ (u_long) dd->dd_desc_len);
530 bus_dmamem_free(dd->dd_dmat, dd->dd_desc, dd->dd_dmamap);
532 bus_dmamap_destroy(dd->dd_dmat, dd->dd_dmamap);
534 bus_dma_tag_destroy(dd->dd_dmat);
535 memset(dd, 0, sizeof(*dd));
539 #define DS2PHYS(_dd, _ds) \
540 ((_dd)->dd_desc_paddr + ((caddr_t)(_ds) - (caddr_t)(_dd)->dd_desc))
543 malo_rxdma_setup(struct malo_softc *sc)
545 struct ifnet *ifp = sc->malo_ifp;
547 struct malo_rxbuf *bf;
548 struct malo_rxdesc *ds;
550 error = malo_desc_setup(sc, "rx", &sc->malo_rxdma,
551 malo_rxbuf, sizeof(struct malo_rxbuf),
552 1, sizeof(struct malo_rxdesc));
557 * Allocate rx buffers and set them up.
559 bsize = malo_rxbuf * sizeof(struct malo_rxbuf);
560 bf = malloc(bsize, M_MALODEV, M_NOWAIT | M_ZERO);
562 if_printf(ifp, "malloc of %u rx buffers failed\n", bsize);
565 sc->malo_rxdma.dd_bufptr = bf;
567 STAILQ_INIT(&sc->malo_rxbuf);
568 ds = sc->malo_rxdma.dd_desc;
569 for (i = 0; i < malo_rxbuf; i++, bf++, ds++) {
571 bf->bf_daddr = DS2PHYS(&sc->malo_rxdma, ds);
572 error = bus_dmamap_create(sc->malo_dmat, BUS_DMA_NOWAIT,
575 if_printf(ifp, "%s: unable to dmamap for rx buffer, "
576 "error %d\n", __func__, error);
579 /* NB: tail is intentional to preserve descriptor order */
580 STAILQ_INSERT_TAIL(&sc->malo_rxbuf, bf, bf_list);
586 malo_txdma_setup(struct malo_softc *sc, struct malo_txq *txq)
588 struct ifnet *ifp = sc->malo_ifp;
590 struct malo_txbuf *bf;
591 struct malo_txdesc *ds;
593 error = malo_desc_setup(sc, "tx", &txq->dma,
594 malo_txbuf, sizeof(struct malo_txbuf),
595 MALO_TXDESC, sizeof(struct malo_txdesc));
599 /* allocate and setup tx buffers */
600 bsize = malo_txbuf * sizeof(struct malo_txbuf);
601 bf = malloc(bsize, M_MALODEV, M_NOWAIT | M_ZERO);
603 if_printf(ifp, "malloc of %u tx buffers failed\n",
607 txq->dma.dd_bufptr = bf;
609 STAILQ_INIT(&txq->free);
611 ds = txq->dma.dd_desc;
612 for (i = 0; i < malo_txbuf; i++, bf++, ds += MALO_TXDESC) {
614 bf->bf_daddr = DS2PHYS(&txq->dma, ds);
615 error = bus_dmamap_create(sc->malo_dmat, BUS_DMA_NOWAIT,
618 if_printf(ifp, "unable to create dmamap for tx "
619 "buffer %u, error %u\n", i, error);
622 STAILQ_INSERT_TAIL(&txq->free, bf, bf_list);
630 malo_desc_cleanup(struct malo_softc *sc, struct malo_descdma *dd)
632 bus_dmamap_unload(dd->dd_dmat, dd->dd_dmamap);
633 bus_dmamem_free(dd->dd_dmat, dd->dd_desc, dd->dd_dmamap);
634 bus_dmamap_destroy(dd->dd_dmat, dd->dd_dmamap);
635 bus_dma_tag_destroy(dd->dd_dmat);
637 memset(dd, 0, sizeof(*dd));
641 malo_rxdma_cleanup(struct malo_softc *sc)
643 struct malo_rxbuf *bf;
645 STAILQ_FOREACH(bf, &sc->malo_rxbuf, bf_list) {
646 if (bf->bf_m != NULL) {
650 if (bf->bf_dmamap != NULL) {
651 bus_dmamap_destroy(sc->malo_dmat, bf->bf_dmamap);
652 bf->bf_dmamap = NULL;
655 STAILQ_INIT(&sc->malo_rxbuf);
656 if (sc->malo_rxdma.dd_bufptr != NULL) {
657 free(sc->malo_rxdma.dd_bufptr, M_MALODEV);
658 sc->malo_rxdma.dd_bufptr = NULL;
660 if (sc->malo_rxdma.dd_desc_len != 0)
661 malo_desc_cleanup(sc, &sc->malo_rxdma);
665 malo_txdma_cleanup(struct malo_softc *sc, struct malo_txq *txq)
667 struct malo_txbuf *bf;
668 struct ieee80211_node *ni;
670 STAILQ_FOREACH(bf, &txq->free, bf_list) {
671 if (bf->bf_m != NULL) {
679 * Reclaim node reference.
681 ieee80211_free_node(ni);
683 if (bf->bf_dmamap != NULL) {
684 bus_dmamap_destroy(sc->malo_dmat, bf->bf_dmamap);
685 bf->bf_dmamap = NULL;
688 STAILQ_INIT(&txq->free);
690 if (txq->dma.dd_bufptr != NULL) {
691 free(txq->dma.dd_bufptr, M_MALODEV);
692 txq->dma.dd_bufptr = NULL;
694 if (txq->dma.dd_desc_len != 0)
695 malo_desc_cleanup(sc, &txq->dma);
699 malo_dma_cleanup(struct malo_softc *sc)
703 for (i = 0; i < MALO_NUM_TX_QUEUES; i++)
704 malo_txdma_cleanup(sc, &sc->malo_txq[i]);
706 malo_rxdma_cleanup(sc);
710 malo_dma_setup(struct malo_softc *sc)
714 /* rxdma initializing. */
715 error = malo_rxdma_setup(sc);
719 /* NB: we just have 1 tx queue now. */
720 for (i = 0; i < MALO_NUM_TX_QUEUES; i++) {
721 error = malo_txdma_setup(sc, &sc->malo_txq[i]);
723 malo_dma_cleanup(sc);
728 malo_txq_init(sc, &sc->malo_txq[i], i);
735 malo_hal_set_rxtxdma(struct malo_softc *sc)
739 malo_bar0_write4(sc, sc->malo_hwspecs.rxdesc_read,
740 sc->malo_hwdma.rxdesc_read);
741 malo_bar0_write4(sc, sc->malo_hwspecs.rxdesc_write,
742 sc->malo_hwdma.rxdesc_read);
744 for (i = 0; i < MALO_NUM_TX_QUEUES; i++) {
746 sc->malo_hwspecs.wcbbase[i], sc->malo_hwdma.wcbbase[i]);
751 * Inform firmware of our tx/rx dma setup. The BAR 0 writes below are
752 * for compatibility with older firmware. For current firmware we send
753 * this information with a cmd block via malo_hal_sethwdma.
756 malo_setup_hwdma(struct malo_softc *sc)
759 struct malo_txq *txq;
761 sc->malo_hwdma.rxdesc_read = sc->malo_rxdma.dd_desc_paddr;
763 for (i = 0; i < MALO_NUM_TX_QUEUES; i++) {
764 txq = &sc->malo_txq[i];
765 sc->malo_hwdma.wcbbase[i] = txq->dma.dd_desc_paddr;
767 sc->malo_hwdma.maxnum_txwcb = malo_txbuf;
768 sc->malo_hwdma.maxnum_wcb = MALO_NUM_TX_QUEUES;
770 malo_hal_set_rxtxdma(sc);
776 malo_txq_init(struct malo_softc *sc, struct malo_txq *txq, int qnum)
778 struct malo_txbuf *bf, *bn;
779 struct malo_txdesc *ds;
781 MALO_TXQ_LOCK_INIT(sc, txq);
783 txq->txpri = 0; /* XXX */
785 STAILQ_FOREACH(bf, &txq->free, bf_list) {
789 bn = STAILQ_NEXT(bf, bf_list);
791 bn = STAILQ_FIRST(&txq->free);
792 ds->physnext = htole32(bn->bf_daddr);
794 STAILQ_INIT(&txq->active);
798 * Reclaim resources for a setup queue.
801 malo_tx_cleanupq(struct malo_softc *sc, struct malo_txq *txq)
804 MALO_TXQ_LOCK_DESTROY(txq);
808 * Allocate a tx buffer for sending a frame.
810 static struct malo_txbuf *
811 malo_getbuf(struct malo_softc *sc, struct malo_txq *txq)
813 struct malo_txbuf *bf;
816 bf = STAILQ_FIRST(&txq->free);
818 STAILQ_REMOVE_HEAD(&txq->free, bf_list);
821 MALO_TXQ_UNLOCK(txq);
823 DPRINTF(sc, MALO_DEBUG_XMIT,
824 "%s: out of xmit buffers on q %d\n", __func__, txq->qnum);
825 sc->malo_stats.mst_tx_qstop++;
831 malo_tx_dmasetup(struct malo_softc *sc, struct malo_txbuf *bf, struct mbuf *m0)
837 * Load the DMA map so any coalescing is done. This also calculates
838 * the number of descriptors we need.
840 error = bus_dmamap_load_mbuf_sg(sc->malo_dmat, bf->bf_dmamap, m0,
841 bf->bf_segs, &bf->bf_nseg,
843 if (error == EFBIG) {
844 /* XXX packet requires too many descriptors */
845 bf->bf_nseg = MALO_TXDESC + 1;
846 } else if (error != 0) {
847 sc->malo_stats.mst_tx_busdma++;
852 * Discard null packets and check for packets that require too many
853 * TX descriptors. We try to convert the latter to a cluster.
855 if (error == EFBIG) { /* too many desc's, linearize */
856 sc->malo_stats.mst_tx_linear++;
857 m = m_defrag(m0, M_NOWAIT);
860 sc->malo_stats.mst_tx_nombuf++;
864 error = bus_dmamap_load_mbuf_sg(sc->malo_dmat, bf->bf_dmamap, m0,
865 bf->bf_segs, &bf->bf_nseg,
868 sc->malo_stats.mst_tx_busdma++;
872 KASSERT(bf->bf_nseg <= MALO_TXDESC,
873 ("too many segments after defrag; nseg %u", bf->bf_nseg));
874 } else if (bf->bf_nseg == 0) { /* null packet, discard */
875 sc->malo_stats.mst_tx_nodata++;
879 DPRINTF(sc, MALO_DEBUG_XMIT, "%s: m %p len %u\n",
880 __func__, m0, m0->m_pkthdr.len);
881 bus_dmamap_sync(sc->malo_dmat, bf->bf_dmamap, BUS_DMASYNC_PREWRITE);
889 malo_printrxbuf(const struct malo_rxbuf *bf, u_int ix)
891 const struct malo_rxdesc *ds = bf->bf_desc;
892 uint32_t status = le32toh(ds->status);
894 printf("R[%2u] (DS.V:%p DS.P:%p) NEXT:%08x DATA:%08x RC:%02x%s\n"
895 " STAT:%02x LEN:%04x SNR:%02x NF:%02x CHAN:%02x"
896 " RATE:%02x QOS:%04x\n",
897 ix, ds, (const struct malo_desc *)bf->bf_daddr,
898 le32toh(ds->physnext), le32toh(ds->physbuffdata),
900 ds->rxcontrol != MALO_RXD_CTRL_DRIVER_OWN ?
901 "" : (status & MALO_RXD_STATUS_OK) ? " *" : " !",
902 ds->status, le16toh(ds->pktlen), ds->snr, ds->nf, ds->channel,
903 ds->rate, le16toh(ds->qosctrl));
907 malo_printtxbuf(const struct malo_txbuf *bf, u_int qnum, u_int ix)
909 const struct malo_txdesc *ds = bf->bf_desc;
910 uint32_t status = le32toh(ds->status);
912 printf("Q%u[%3u]", qnum, ix);
913 printf(" (DS.V:%p DS.P:%p)\n",
914 ds, (const struct malo_txdesc *)bf->bf_daddr);
915 printf(" NEXT:%08x DATA:%08x LEN:%04x STAT:%08x%s\n",
916 le32toh(ds->physnext),
917 le32toh(ds->pktptr), le16toh(ds->pktlen), status,
918 status & MALO_TXD_STATUS_USED ?
919 "" : (status & 3) != 0 ? " *" : " !");
920 printf(" RATE:%02x PRI:%x QOS:%04x SAP:%08x FORMAT:%04x\n",
921 ds->datarate, ds->txpriority, le16toh(ds->qosctrl),
922 le32toh(ds->sap_pktinfo), le16toh(ds->format));
925 const uint8_t *cp = (const uint8_t *) ds;
927 for (i = 0; i < sizeof(struct malo_txdesc); i++) {
928 printf("%02x ", cp[i]);
929 if (((i+1) % 16) == 0)
936 #endif /* MALO_DEBUG */
939 malo_updatetxrate(struct ieee80211_node *ni, int rix)
941 #define N(x) (sizeof(x)/sizeof(x[0]))
942 static const int ieeerates[] =
943 { 2, 4, 11, 22, 44, 12, 18, 24, 36, 48, 96, 108 };
944 if (rix < N(ieeerates))
945 ni->ni_txrate = ieeerates[rix];
950 malo_fix2rate(int fix_rate)
952 #define N(x) (sizeof(x)/sizeof(x[0]))
953 static const int rates[] =
954 { 2, 4, 11, 22, 12, 18, 24, 36, 48, 96, 108 };
955 return (fix_rate < N(rates) ? rates[fix_rate] : 0);
959 /* idiomatic shorthands: MS = mask+shift, SM = shift+mask */
960 #define MS(v,x) (((v) & x) >> x##_S)
961 #define SM(v,x) (((v) << x##_S) & x)
964 * Process completed xmit descriptors from the specified queue.
967 malo_tx_processq(struct malo_softc *sc, struct malo_txq *txq)
969 struct malo_txbuf *bf;
970 struct malo_txdesc *ds;
971 struct ieee80211_node *ni;
975 DPRINTF(sc, MALO_DEBUG_TX_PROC, "%s: tx queue %u\n",
976 __func__, txq->qnum);
977 for (nreaped = 0;; nreaped++) {
979 bf = STAILQ_FIRST(&txq->active);
981 MALO_TXQ_UNLOCK(txq);
985 MALO_TXDESC_SYNC(txq, ds,
986 BUS_DMASYNC_POSTREAD | BUS_DMASYNC_POSTWRITE);
987 if (ds->status & htole32(MALO_TXD_STATUS_FW_OWNED)) {
988 MALO_TXQ_UNLOCK(txq);
991 STAILQ_REMOVE_HEAD(&txq->active, bf_list);
992 MALO_TXQ_UNLOCK(txq);
995 if (sc->malo_debug & MALO_DEBUG_XMIT_DESC)
996 malo_printtxbuf(bf, txq->qnum, nreaped);
1000 status = le32toh(ds->status);
1001 if (status & MALO_TXD_STATUS_OK) {
1002 uint16_t format = le16toh(ds->format);
1003 uint8_t txant = MS(format, MALO_TXD_ANTENNA);
1005 sc->malo_stats.mst_ant_tx[txant]++;
1006 if (status & MALO_TXD_STATUS_OK_RETRY)
1007 sc->malo_stats.mst_tx_retries++;
1008 if (status & MALO_TXD_STATUS_OK_MORE_RETRY)
1009 sc->malo_stats.mst_tx_mretries++;
1010 malo_updatetxrate(ni, ds->datarate);
1011 sc->malo_stats.mst_tx_rate = ds->datarate;
1013 if (status & MALO_TXD_STATUS_FAILED_LINK_ERROR)
1014 sc->malo_stats.mst_tx_linkerror++;
1015 if (status & MALO_TXD_STATUS_FAILED_XRETRY)
1016 sc->malo_stats.mst_tx_xretries++;
1017 if (status & MALO_TXD_STATUS_FAILED_AGING)
1018 sc->malo_stats.mst_tx_aging++;
1021 * Do any tx complete callback. Note this must
1022 * be done before releasing the node reference.
1023 * XXX no way to figure out if frame was ACK'd
1025 if (bf->bf_m->m_flags & M_TXCB) {
1026 /* XXX strip fw len in case header inspected */
1027 m_adj(bf->bf_m, sizeof(uint16_t));
1028 ieee80211_process_callback(ni, bf->bf_m,
1029 (status & MALO_TXD_STATUS_OK) == 0);
1032 * Reclaim reference to node.
1034 * NB: the node may be reclaimed here if, for example
1035 * this is a DEAUTH message that was sent and the
1036 * node was timed out due to inactivity.
1038 ieee80211_free_node(ni);
1040 ds->status = htole32(MALO_TXD_STATUS_IDLE);
1041 ds->pktlen = htole32(0);
1043 bus_dmamap_sync(sc->malo_dmat, bf->bf_dmamap,
1044 BUS_DMASYNC_POSTWRITE);
1045 bus_dmamap_unload(sc->malo_dmat, bf->bf_dmamap);
1051 STAILQ_INSERT_TAIL(&txq->free, bf, bf_list);
1053 MALO_TXQ_UNLOCK(txq);
1059 * Deferred processing of transmit interrupt.
1062 malo_tx_proc(void *arg, int npending)
1064 struct malo_softc *sc = arg;
1065 struct ifnet *ifp = sc->malo_ifp;
1069 * Process each active queue.
1072 for (i = 0; i < MALO_NUM_TX_QUEUES; i++) {
1073 if (!STAILQ_EMPTY(&sc->malo_txq[i].active))
1074 nreaped += malo_tx_processq(sc, &sc->malo_txq[i]);
1078 ifp->if_drv_flags &= ~IFF_DRV_OACTIVE;
1085 malo_tx_start(struct malo_softc *sc, struct ieee80211_node *ni,
1086 struct malo_txbuf *bf, struct mbuf *m0)
1088 #define IEEE80211_DIR_DSTODS(wh) \
1089 ((wh->i_fc[1] & IEEE80211_FC1_DIR_MASK) == IEEE80211_FC1_DIR_DSTODS)
1090 #define IS_DATA_FRAME(wh) \
1091 ((wh->i_fc[0] & (IEEE80211_FC0_TYPE_MASK)) == IEEE80211_FC0_TYPE_DATA)
1092 int error, ismcast, iswep;
1093 int copyhdrlen, hdrlen, pktlen;
1094 struct ieee80211_frame *wh;
1095 struct ifnet *ifp = sc->malo_ifp;
1096 struct ieee80211com *ic = ifp->if_l2com;
1097 struct ieee80211vap *vap = ni->ni_vap;
1098 struct malo_txdesc *ds;
1099 struct malo_txrec *tr;
1100 struct malo_txq *txq;
1103 wh = mtod(m0, struct ieee80211_frame *);
1104 iswep = wh->i_fc[1] & IEEE80211_FC1_WEP;
1105 ismcast = IEEE80211_IS_MULTICAST(wh->i_addr1);
1106 copyhdrlen = hdrlen = ieee80211_anyhdrsize(wh);
1107 pktlen = m0->m_pkthdr.len;
1108 if (IEEE80211_QOS_HAS_SEQ(wh)) {
1109 if (IEEE80211_DIR_DSTODS(wh)) {
1111 (((struct ieee80211_qosframe_addr4 *) wh)->i_qos);
1112 copyhdrlen -= sizeof(qos);
1115 (((struct ieee80211_qosframe *) wh)->i_qos);
1120 struct ieee80211_key *k;
1123 * Construct the 802.11 header+trailer for an encrypted
1124 * frame. The only reason this can fail is because of an
1125 * unknown or unsupported cipher/key type.
1127 * NB: we do this even though the firmware will ignore
1128 * what we've done for WEP and TKIP as we need the
1129 * ExtIV filled in for CCMP and this also adjusts
1130 * the headers which simplifies our work below.
1132 k = ieee80211_crypto_encap(ni, m0);
1135 * This can happen when the key is yanked after the
1136 * frame was queued. Just discard the frame; the
1137 * 802.11 layer counts failures and provides
1138 * debugging/diagnostics.
1145 * Adjust the packet length for the crypto additions
1146 * done during encap and any other bits that the f/w
1147 * will add later on.
1149 pktlen = m0->m_pkthdr.len;
1151 /* packet header may have moved, reset our local pointer */
1152 wh = mtod(m0, struct ieee80211_frame *);
1155 if (ieee80211_radiotap_active_vap(vap)) {
1156 sc->malo_tx_th.wt_flags = 0; /* XXX */
1158 sc->malo_tx_th.wt_flags |= IEEE80211_RADIOTAP_F_WEP;
1159 sc->malo_tx_th.wt_txpower = ni->ni_txpower;
1160 sc->malo_tx_th.wt_antenna = sc->malo_txantenna;
1162 ieee80211_radiotap_tx(vap, m0);
1166 * Copy up/down the 802.11 header; the firmware requires
1167 * we present a 2-byte payload length followed by a
1168 * 4-address header (w/o QoS), followed (optionally) by
1169 * any WEP/ExtIV header (but only filled in for CCMP).
1170 * We are assured the mbuf has sufficient headroom to
1171 * prepend in-place by the setup of ic_headroom in
1174 if (hdrlen < sizeof(struct malo_txrec)) {
1175 const int space = sizeof(struct malo_txrec) - hdrlen;
1176 if (M_LEADINGSPACE(m0) < space) {
1177 /* NB: should never happen */
1178 device_printf(sc->malo_dev,
1179 "not enough headroom, need %d found %zd, "
1180 "m_flags 0x%x m_len %d\n",
1181 space, M_LEADINGSPACE(m0), m0->m_flags, m0->m_len);
1182 ieee80211_dump_pkt(ic,
1183 mtod(m0, const uint8_t *), m0->m_len, 0, -1);
1188 M_PREPEND(m0, space, M_NOWAIT);
1190 tr = mtod(m0, struct malo_txrec *);
1191 if (wh != (struct ieee80211_frame *) &tr->wh)
1192 ovbcopy(wh, &tr->wh, hdrlen);
1194 * Note: the "firmware length" is actually the length of the fully
1195 * formed "802.11 payload". That is, it's everything except for
1196 * the 802.11 header. In particular this includes all crypto
1197 * material including the MIC!
1199 tr->fwlen = htole16(pktlen - hdrlen);
1202 * Load the DMA map so any coalescing is done. This
1203 * also calculates the number of descriptors we need.
1205 error = malo_tx_dmasetup(sc, bf, m0);
1208 bf->bf_node = ni; /* NB: held reference */
1209 m0 = bf->bf_m; /* NB: may have changed */
1210 tr = mtod(m0, struct malo_txrec *);
1211 wh = (struct ieee80211_frame *)&tr->wh;
1214 * Formulate tx descriptor.
1219 ds->qosctrl = qos; /* NB: already little-endian */
1220 ds->pktptr = htole32(bf->bf_segs[0].ds_addr);
1221 ds->pktlen = htole16(bf->bf_segs[0].ds_len);
1222 /* NB: pPhysNext setup once, don't touch */
1223 ds->datarate = IS_DATA_FRAME(wh) ? 1 : 0;
1224 ds->sap_pktinfo = 0;
1228 * Select transmit rate.
1230 switch (wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK) {
1231 case IEEE80211_FC0_TYPE_MGT:
1232 sc->malo_stats.mst_tx_mgmt++;
1234 case IEEE80211_FC0_TYPE_CTL:
1237 case IEEE80211_FC0_TYPE_DATA:
1238 ds->txpriority = txq->qnum;
1241 if_printf(ifp, "bogus frame type 0x%x (%s)\n",
1242 wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK, __func__);
1249 if (IFF_DUMPPKTS_XMIT(sc))
1250 ieee80211_dump_pkt(ic,
1251 mtod(m0, const uint8_t *)+sizeof(uint16_t),
1252 m0->m_len - sizeof(uint16_t), ds->datarate, -1);
1256 if (!IS_DATA_FRAME(wh))
1257 ds->status |= htole32(1);
1258 ds->status |= htole32(MALO_TXD_STATUS_FW_OWNED);
1259 STAILQ_INSERT_TAIL(&txq->active, bf, bf_list);
1260 MALO_TXDESC_SYNC(txq, ds, BUS_DMASYNC_PREREAD | BUS_DMASYNC_PREWRITE);
1264 MALO_TXQ_UNLOCK(txq);
1266 #undef IEEE80211_DIR_DSTODS
1270 malo_start(struct ifnet *ifp)
1272 struct malo_softc *sc = ifp->if_softc;
1273 struct ieee80211_node *ni;
1274 struct malo_txq *txq = &sc->malo_txq[0];
1275 struct malo_txbuf *bf = NULL;
1279 if ((ifp->if_drv_flags & IFF_DRV_RUNNING) == 0 || sc->malo_invalid)
1283 IFQ_DRV_DEQUEUE(&ifp->if_snd, m);
1286 ni = (struct ieee80211_node *) m->m_pkthdr.rcvif;
1287 bf = malo_getbuf(sc, txq);
1289 IFQ_DRV_PREPEND(&ifp->if_snd, m);
1291 /* XXX blocks other traffic */
1292 ifp->if_drv_flags |= IFF_DRV_OACTIVE;
1293 sc->malo_stats.mst_tx_qstop++;
1297 * Pass the frame to the h/w for transmission.
1299 if (malo_tx_start(sc, ni, bf, m)) {
1305 STAILQ_INSERT_HEAD(&txq->free, bf, bf_list);
1306 MALO_TXQ_UNLOCK(txq);
1308 ieee80211_free_node(ni);
1313 if (nqueued >= malo_txcoalesce) {
1315 * Poke the firmware to process queued frames;
1316 * see below about (lack of) locking.
1319 malo_hal_txstart(sc->malo_mh, 0/*XXX*/);
1325 * NB: We don't need to lock against tx done because
1326 * this just prods the firmware to check the transmit
1327 * descriptors. The firmware will also start fetching
1328 * descriptors by itself if it notices new ones are
1329 * present when it goes to deliver a tx done interrupt
1330 * to the host. So if we race with tx done processing
1331 * it's ok. Delivering the kick here rather than in
1332 * malo_tx_start is an optimization to avoid poking the
1333 * firmware for each packet.
1335 * NB: the queue id isn't used so 0 is ok.
1337 malo_hal_txstart(sc->malo_mh, 0/*XXX*/);
1342 malo_watchdog(void *arg)
1344 struct malo_softc *sc;
1348 callout_reset(&sc->malo_watchdog_timer, hz, malo_watchdog, sc);
1349 if (sc->malo_timer == 0 || --sc->malo_timer > 0)
1353 if ((ifp->if_drv_flags & IFF_DRV_RUNNING) && !sc->malo_invalid) {
1354 if_printf(ifp, "watchdog timeout\n");
1356 /* XXX no way to reset h/w. now */
1359 sc->malo_stats.mst_watchdog++;
1364 malo_hal_reset(struct malo_softc *sc)
1366 static int first = 0;
1367 struct ifnet *ifp = sc->malo_ifp;
1368 struct ieee80211com *ic = ifp->if_l2com;
1369 struct malo_hal *mh = sc->malo_mh;
1373 * NB: when the device firstly is initialized, sometimes
1374 * firmware could override rx/tx dma registers so we re-set
1375 * these values once.
1377 malo_hal_set_rxtxdma(sc);
1381 malo_hal_setantenna(mh, MHA_ANTENNATYPE_RX, sc->malo_rxantenna);
1382 malo_hal_setantenna(mh, MHA_ANTENNATYPE_TX, sc->malo_txantenna);
1383 malo_hal_setradio(mh, 1, MHP_AUTO_PREAMBLE);
1384 malo_chan_set(sc, ic->ic_curchan);
1386 /* XXX needs other stuffs? */
1391 static __inline struct mbuf *
1392 malo_getrxmbuf(struct malo_softc *sc, struct malo_rxbuf *bf)
1398 /* XXX don't need mbuf, just dma buffer */
1399 m = m_getjcl(M_NOWAIT, MT_DATA, M_PKTHDR, MJUMPAGESIZE);
1401 sc->malo_stats.mst_rx_nombuf++; /* XXX */
1404 error = bus_dmamap_load(sc->malo_dmat, bf->bf_dmamap,
1405 mtod(m, caddr_t), MJUMPAGESIZE,
1406 malo_load_cb, &paddr, BUS_DMA_NOWAIT);
1408 if_printf(sc->malo_ifp,
1409 "%s: bus_dmamap_load failed, error %d\n", __func__, error);
1413 bf->bf_data = paddr;
1414 bus_dmamap_sync(sc->malo_dmat, bf->bf_dmamap, BUS_DMASYNC_PREWRITE);
1420 malo_rxbuf_init(struct malo_softc *sc, struct malo_rxbuf *bf)
1422 struct malo_rxdesc *ds;
1425 if (bf->bf_m == NULL) {
1426 bf->bf_m = malo_getrxmbuf(sc, bf);
1427 if (bf->bf_m == NULL) {
1428 /* mark descriptor to be skipped */
1429 ds->rxcontrol = MALO_RXD_CTRL_OS_OWN;
1430 /* NB: don't need PREREAD */
1431 MALO_RXDESC_SYNC(sc, ds, BUS_DMASYNC_PREWRITE);
1441 ds->status = MALO_RXD_STATUS_IDLE;
1443 ds->pktlen = htole16(MALO_RXSIZE);
1445 ds->physbuffdata = htole32(bf->bf_data);
1446 /* NB: don't touch pPhysNext, set once */
1447 ds->rxcontrol = MALO_RXD_CTRL_DRIVER_OWN;
1448 MALO_RXDESC_SYNC(sc, ds, BUS_DMASYNC_PREREAD | BUS_DMASYNC_PREWRITE);
1454 * Setup the rx data structures. This should only be done once or we may get
1455 * out of sync with the firmware.
1458 malo_startrecv(struct malo_softc *sc)
1460 struct malo_rxbuf *bf, *prev;
1461 struct malo_rxdesc *ds;
1463 if (sc->malo_recvsetup == 1) {
1464 malo_mode_init(sc); /* set filters, etc. */
1469 STAILQ_FOREACH(bf, &sc->malo_rxbuf, bf_list) {
1470 int error = malo_rxbuf_init(sc, bf);
1472 DPRINTF(sc, MALO_DEBUG_RECV,
1473 "%s: malo_rxbuf_init failed %d\n",
1479 ds->physnext = htole32(bf->bf_daddr);
1486 htole32(STAILQ_FIRST(&sc->malo_rxbuf)->bf_daddr);
1489 sc->malo_recvsetup = 1;
1491 malo_mode_init(sc); /* set filters, etc. */
1497 malo_init_locked(struct malo_softc *sc)
1499 struct ifnet *ifp = sc->malo_ifp;
1500 struct malo_hal *mh = sc->malo_mh;
1503 DPRINTF(sc, MALO_DEBUG_ANY, "%s: if_flags 0x%x\n",
1504 __func__, ifp->if_flags);
1506 MALO_LOCK_ASSERT(sc);
1509 * Stop anything previously setup. This is safe whether this is
1510 * the first time through or not.
1512 malo_stop_locked(ifp, 0);
1515 * Push state to the firmware.
1517 if (!malo_hal_reset(sc)) {
1518 if_printf(ifp, "%s: unable to reset hardware\n", __func__);
1523 * Setup recv (once); transmit is already good to go.
1525 error = malo_startrecv(sc);
1527 if_printf(ifp, "%s: unable to start recv logic, error %d\n",
1533 * Enable interrupts.
1535 sc->malo_imask = MALO_A2HRIC_BIT_RX_RDY
1536 | MALO_A2HRIC_BIT_TX_DONE
1537 | MALO_A2HRIC_BIT_OPC_DONE
1538 | MALO_A2HRIC_BIT_MAC_EVENT
1539 | MALO_A2HRIC_BIT_RX_PROBLEM
1540 | MALO_A2HRIC_BIT_ICV_ERROR
1541 | MALO_A2HRIC_BIT_RADAR_DETECT
1542 | MALO_A2HRIC_BIT_CHAN_SWITCH;
1544 ifp->if_drv_flags |= IFF_DRV_RUNNING;
1545 malo_hal_intrset(mh, sc->malo_imask);
1546 callout_reset(&sc->malo_watchdog_timer, hz, malo_watchdog, sc);
1550 malo_init(void *arg)
1552 struct malo_softc *sc = (struct malo_softc *) arg;
1553 struct ifnet *ifp = sc->malo_ifp;
1554 struct ieee80211com *ic = ifp->if_l2com;
1556 DPRINTF(sc, MALO_DEBUG_ANY, "%s: if_flags 0x%x\n",
1557 __func__, ifp->if_flags);
1560 malo_init_locked(sc);
1564 if (ifp->if_drv_flags & IFF_DRV_RUNNING)
1565 ieee80211_start_all(ic); /* start all vap's */
1569 * Set the multicast filter contents into the hardware.
1572 malo_setmcastfilter(struct malo_softc *sc)
1574 struct ifnet *ifp = sc->malo_ifp;
1575 struct ieee80211com *ic = ifp->if_l2com;
1576 struct ifmultiaddr *ifma;
1577 uint8_t macs[IEEE80211_ADDR_LEN * MALO_HAL_MCAST_MAX];
1584 if (ic->ic_opmode == IEEE80211_M_MONITOR ||
1585 (ifp->if_flags & (IFF_ALLMULTI | IFF_PROMISC)))
1588 if_maddr_rlock(ifp);
1589 TAILQ_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link) {
1590 if (ifma->ifma_addr->sa_family != AF_LINK)
1593 if (nmc == MALO_HAL_MCAST_MAX) {
1594 ifp->if_flags |= IFF_ALLMULTI;
1595 if_maddr_runlock(ifp);
1598 IEEE80211_ADDR_COPY(mp,
1599 LLADDR((struct sockaddr_dl *)ifma->ifma_addr));
1601 mp += IEEE80211_ADDR_LEN, nmc++;
1603 if_maddr_runlock(ifp);
1605 malo_hal_setmcast(sc->malo_mh, nmc, macs);
1609 * XXX we don't know how to set the f/w for supporting
1610 * IFF_ALLMULTI | IFF_PROMISC cases
1616 malo_mode_init(struct malo_softc *sc)
1618 struct ifnet *ifp = sc->malo_ifp;
1619 struct ieee80211com *ic = ifp->if_l2com;
1620 struct malo_hal *mh = sc->malo_mh;
1623 * NB: Ignore promisc in hostap mode; it's set by the
1624 * bridge. This is wrong but we have no way to
1625 * identify internal requests (from the bridge)
1626 * versus external requests such as for tcpdump.
1628 malo_hal_setpromisc(mh, (ifp->if_flags & IFF_PROMISC) &&
1629 ic->ic_opmode != IEEE80211_M_HOSTAP);
1630 malo_setmcastfilter(sc);
1636 malo_tx_draintxq(struct malo_softc *sc, struct malo_txq *txq)
1638 struct ieee80211_node *ni;
1639 struct malo_txbuf *bf;
1643 * NB: this assumes output has been stopped and
1644 * we do not need to block malo_tx_tasklet
1646 for (ix = 0;; ix++) {
1648 bf = STAILQ_FIRST(&txq->active);
1650 MALO_TXQ_UNLOCK(txq);
1653 STAILQ_REMOVE_HEAD(&txq->active, bf_list);
1654 MALO_TXQ_UNLOCK(txq);
1656 if (sc->malo_debug & MALO_DEBUG_RESET) {
1657 struct ifnet *ifp = sc->malo_ifp;
1658 struct ieee80211com *ic = ifp->if_l2com;
1659 const struct malo_txrec *tr =
1660 mtod(bf->bf_m, const struct malo_txrec *);
1661 malo_printtxbuf(bf, txq->qnum, ix);
1662 ieee80211_dump_pkt(ic, (const uint8_t *)&tr->wh,
1663 bf->bf_m->m_len - sizeof(tr->fwlen), 0, -1);
1665 #endif /* MALO_DEBUG */
1666 bus_dmamap_unload(sc->malo_dmat, bf->bf_dmamap);
1671 * Reclaim node reference.
1673 ieee80211_free_node(ni);
1679 STAILQ_INSERT_TAIL(&txq->free, bf, bf_list);
1681 MALO_TXQ_UNLOCK(txq);
1686 malo_stop_locked(struct ifnet *ifp, int disable)
1688 struct malo_softc *sc = ifp->if_softc;
1689 struct malo_hal *mh = sc->malo_mh;
1692 DPRINTF(sc, MALO_DEBUG_ANY, "%s: invalid %u if_flags 0x%x\n",
1693 __func__, sc->malo_invalid, ifp->if_flags);
1695 MALO_LOCK_ASSERT(sc);
1697 if (!(ifp->if_drv_flags & IFF_DRV_RUNNING))
1701 * Shutdown the hardware and driver:
1702 * disable interrupts
1703 * turn off the radio
1704 * drain and release tx queues
1706 * Note that some of this work is not possible if the hardware
1707 * is gone (invalid).
1709 ifp->if_drv_flags &= ~IFF_DRV_RUNNING;
1710 callout_stop(&sc->malo_watchdog_timer);
1712 /* diable interrupt. */
1713 malo_hal_intrset(mh, 0);
1714 /* turn off the radio. */
1715 malo_hal_setradio(mh, 0, MHP_AUTO_PREAMBLE);
1717 /* drain and release tx queues. */
1718 for (i = 0; i < MALO_NUM_TX_QUEUES; i++)
1719 malo_tx_draintxq(sc, &sc->malo_txq[i]);
1723 malo_ioctl(struct ifnet *ifp, u_long cmd, caddr_t data)
1725 #define MALO_IS_RUNNING(ifp) \
1726 ((ifp->if_flags & IFF_UP) && (ifp->if_drv_flags & IFF_DRV_RUNNING))
1727 struct malo_softc *sc = ifp->if_softc;
1728 struct ieee80211com *ic = ifp->if_l2com;
1729 struct ifreq *ifr = (struct ifreq *) data;
1730 int error = 0, startall = 0;
1735 if (MALO_IS_RUNNING(ifp)) {
1737 * To avoid rescanning another access point,
1738 * do not call malo_init() here. Instead,
1739 * only reflect promisc mode settings.
1742 } else if (ifp->if_flags & IFF_UP) {
1744 * Beware of being called during attach/detach
1745 * to reset promiscuous mode. In that case we
1746 * will still be marked UP but not RUNNING.
1747 * However trying to re-init the interface
1748 * is the wrong thing to do as we've already
1749 * torn down much of our state. There's
1750 * probably a better way to deal with this.
1752 if (!sc->malo_invalid) {
1753 malo_init_locked(sc);
1757 malo_stop_locked(ifp, 1);
1761 error = ifmedia_ioctl(ifp, ifr, &ic->ic_media, cmd);
1764 error = ether_ioctl(ifp, cmd, data);
1770 ieee80211_start_all(ic);
1772 #undef MALO_IS_RUNNING
1776 * Callback from the 802.11 layer to update the slot time
1777 * based on the current setting. We use it to notify the
1778 * firmware of ERP changes and the f/w takes care of things
1779 * like slot time and preamble.
1782 malo_updateslot(struct ifnet *ifp)
1784 struct malo_softc *sc = ifp->if_softc;
1785 struct ieee80211com *ic = ifp->if_l2com;
1786 struct malo_hal *mh = sc->malo_mh;
1789 /* NB: can be called early; suppress needless cmds */
1790 if ((ifp->if_drv_flags & IFF_DRV_RUNNING) == 0)
1793 DPRINTF(sc, MALO_DEBUG_RESET,
1794 "%s: chan %u MHz/flags 0x%x %s slot, (ic_flags 0x%x)\n",
1795 __func__, ic->ic_curchan->ic_freq, ic->ic_curchan->ic_flags,
1796 ic->ic_flags & IEEE80211_F_SHSLOT ? "short" : "long", ic->ic_flags);
1798 if (ic->ic_flags & IEEE80211_F_SHSLOT)
1799 error = malo_hal_set_slot(mh, 1);
1801 error = malo_hal_set_slot(mh, 0);
1804 device_printf(sc->malo_dev, "setting %s slot failed\n",
1805 ic->ic_flags & IEEE80211_F_SHSLOT ? "short" : "long");
1809 malo_newstate(struct ieee80211vap *vap, enum ieee80211_state nstate, int arg)
1811 struct ieee80211com *ic = vap->iv_ic;
1812 struct malo_softc *sc = ic->ic_ifp->if_softc;
1813 struct malo_hal *mh = sc->malo_mh;
1816 DPRINTF(sc, MALO_DEBUG_STATE, "%s: %s -> %s\n", __func__,
1817 ieee80211_state_name[vap->iv_state],
1818 ieee80211_state_name[nstate]);
1821 * Invoke the net80211 layer first so iv_bss is setup.
1823 error = MALO_VAP(vap)->malo_newstate(vap, nstate, arg);
1827 if (nstate == IEEE80211_S_RUN && vap->iv_state != IEEE80211_S_RUN) {
1828 struct ieee80211_node *ni = vap->iv_bss;
1829 enum ieee80211_phymode mode = ieee80211_chan2mode(ni->ni_chan);
1830 const struct ieee80211_txparam *tp = &vap->iv_txparms[mode];
1832 DPRINTF(sc, MALO_DEBUG_STATE,
1833 "%s: %s(RUN): iv_flags 0x%08x bintvl %d bssid %s "
1834 "capinfo 0x%04x chan %d associd 0x%x mode %d rate %d\n",
1835 vap->iv_ifp->if_xname, __func__, vap->iv_flags,
1836 ni->ni_intval, ether_sprintf(ni->ni_bssid), ni->ni_capinfo,
1837 ieee80211_chan2ieee(ic, ic->ic_curchan),
1838 ni->ni_associd, mode, tp->ucastrate);
1840 malo_hal_setradio(mh, 1,
1841 (ic->ic_flags & IEEE80211_F_SHPREAMBLE) ?
1842 MHP_SHORT_PREAMBLE : MHP_LONG_PREAMBLE);
1843 malo_hal_setassocid(sc->malo_mh, ni->ni_bssid, ni->ni_associd);
1844 malo_hal_set_rate(mh, mode,
1845 tp->ucastrate == IEEE80211_FIXED_RATE_NONE ?
1846 0 : malo_fix2rate(tp->ucastrate));
1852 malo_raw_xmit(struct ieee80211_node *ni, struct mbuf *m,
1853 const struct ieee80211_bpf_params *params)
1855 struct ieee80211com *ic = ni->ni_ic;
1856 struct ifnet *ifp = ic->ic_ifp;
1857 struct malo_softc *sc = ifp->if_softc;
1858 struct malo_txbuf *bf;
1859 struct malo_txq *txq;
1861 if ((ifp->if_drv_flags & IFF_DRV_RUNNING) == 0 || sc->malo_invalid) {
1862 ieee80211_free_node(ni);
1868 * Grab a TX buffer and associated resources. Note that we depend
1869 * on the classification by the 802.11 layer to get to the right h/w
1870 * queue. Management frames must ALWAYS go on queue 1 but we
1871 * cannot just force that here because we may receive non-mgt frames.
1873 txq = &sc->malo_txq[0];
1874 bf = malo_getbuf(sc, txq);
1876 /* XXX blocks other traffic */
1877 ifp->if_drv_flags |= IFF_DRV_OACTIVE;
1878 ieee80211_free_node(ni);
1884 * Pass the frame to the h/w for transmission.
1886 if (malo_tx_start(sc, ni, bf, m) != 0) {
1891 STAILQ_INSERT_HEAD(&txq->free, bf, bf_list);
1893 MALO_TXQ_UNLOCK(txq);
1895 ieee80211_free_node(ni);
1896 return EIO; /* XXX */
1900 * NB: We don't need to lock against tx done because this just
1901 * prods the firmware to check the transmit descriptors. The firmware
1902 * will also start fetching descriptors by itself if it notices
1903 * new ones are present when it goes to deliver a tx done interrupt
1904 * to the host. So if we race with tx done processing it's ok.
1905 * Delivering the kick here rather than in malo_tx_start is
1906 * an optimization to avoid poking the firmware for each packet.
1908 * NB: the queue id isn't used so 0 is ok.
1910 malo_hal_txstart(sc->malo_mh, 0/*XXX*/);
1916 malo_sysctlattach(struct malo_softc *sc)
1919 struct sysctl_ctx_list *ctx = device_get_sysctl_ctx(sc->malo_dev);
1920 struct sysctl_oid *tree = device_get_sysctl_tree(sc->malo_dev);
1922 sc->malo_debug = malo_debug;
1923 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
1924 "debug", CTLFLAG_RW, &sc->malo_debug, 0,
1925 "control debugging printfs");
1930 malo_announce(struct malo_softc *sc)
1932 struct ifnet *ifp = sc->malo_ifp;
1934 if_printf(ifp, "versions [hw %d fw %d.%d.%d.%d] (regioncode %d)\n",
1935 sc->malo_hwspecs.hwversion,
1936 (sc->malo_hwspecs.fw_releasenum >> 24) & 0xff,
1937 (sc->malo_hwspecs.fw_releasenum >> 16) & 0xff,
1938 (sc->malo_hwspecs.fw_releasenum >> 8) & 0xff,
1939 (sc->malo_hwspecs.fw_releasenum >> 0) & 0xff,
1940 sc->malo_hwspecs.regioncode);
1942 if (bootverbose || malo_rxbuf != MALO_RXBUF)
1943 if_printf(ifp, "using %u rx buffers\n", malo_rxbuf);
1944 if (bootverbose || malo_txbuf != MALO_TXBUF)
1945 if_printf(ifp, "using %u tx buffers\n", malo_txbuf);
1949 * Convert net80211 channel to a HAL channel.
1952 malo_mapchan(struct malo_hal_channel *hc, const struct ieee80211_channel *chan)
1954 hc->channel = chan->ic_ieee;
1956 *(uint32_t *)&hc->flags = 0;
1957 if (IEEE80211_IS_CHAN_2GHZ(chan))
1958 hc->flags.freqband = MALO_FREQ_BAND_2DOT4GHZ;
1962 * Set/change channels. If the channel is really being changed,
1963 * it's done by reseting the chip. To accomplish this we must
1964 * first cleanup any pending DMA, then restart stuff after a la
1968 malo_chan_set(struct malo_softc *sc, struct ieee80211_channel *chan)
1970 struct malo_hal *mh = sc->malo_mh;
1971 struct malo_hal_channel hchan;
1973 DPRINTF(sc, MALO_DEBUG_RESET, "%s: chan %u MHz/flags 0x%x\n",
1974 __func__, chan->ic_freq, chan->ic_flags);
1977 * Convert to a HAL channel description with the flags constrained
1978 * to reflect the current operating mode.
1980 malo_mapchan(&hchan, chan);
1981 malo_hal_intrset(mh, 0); /* disable interrupts */
1982 malo_hal_setchannel(mh, &hchan);
1983 malo_hal_settxpower(mh, &hchan);
1986 * Update internal state.
1988 sc->malo_tx_th.wt_chan_freq = htole16(chan->ic_freq);
1989 sc->malo_rx_th.wr_chan_freq = htole16(chan->ic_freq);
1990 if (IEEE80211_IS_CHAN_ANYG(chan)) {
1991 sc->malo_tx_th.wt_chan_flags = htole16(IEEE80211_CHAN_G);
1992 sc->malo_rx_th.wr_chan_flags = htole16(IEEE80211_CHAN_G);
1994 sc->malo_tx_th.wt_chan_flags = htole16(IEEE80211_CHAN_B);
1995 sc->malo_rx_th.wr_chan_flags = htole16(IEEE80211_CHAN_B);
1997 sc->malo_curchan = hchan;
1998 malo_hal_intrset(mh, sc->malo_imask);
2004 malo_scan_start(struct ieee80211com *ic)
2006 struct ifnet *ifp = ic->ic_ifp;
2007 struct malo_softc *sc = ifp->if_softc;
2009 DPRINTF(sc, MALO_DEBUG_STATE, "%s\n", __func__);
2013 malo_scan_end(struct ieee80211com *ic)
2015 struct ifnet *ifp = ic->ic_ifp;
2016 struct malo_softc *sc = ifp->if_softc;
2018 DPRINTF(sc, MALO_DEBUG_STATE, "%s\n", __func__);
2022 malo_set_channel(struct ieee80211com *ic)
2024 struct ifnet *ifp = ic->ic_ifp;
2025 struct malo_softc *sc = ifp->if_softc;
2027 (void) malo_chan_set(sc, ic->ic_curchan);
2031 malo_rx_proc(void *arg, int npending)
2033 #define IEEE80211_DIR_DSTODS(wh) \
2034 ((((const struct ieee80211_frame *)wh)->i_fc[1] & \
2035 IEEE80211_FC1_DIR_MASK) == IEEE80211_FC1_DIR_DSTODS)
2036 struct malo_softc *sc = arg;
2037 struct ifnet *ifp = sc->malo_ifp;
2038 struct ieee80211com *ic = ifp->if_l2com;
2039 struct malo_rxbuf *bf;
2040 struct malo_rxdesc *ds;
2041 struct mbuf *m, *mnew;
2042 struct ieee80211_qosframe *wh;
2043 struct ieee80211_qosframe_addr4 *wh4;
2044 struct ieee80211_node *ni;
2045 int off, len, hdrlen, pktlen, rssi, ntodo;
2046 uint8_t *data, status;
2047 uint32_t readptr, writeptr;
2049 DPRINTF(sc, MALO_DEBUG_RX_PROC,
2050 "%s: pending %u rdptr(0x%x) 0x%x wrptr(0x%x) 0x%x\n",
2052 sc->malo_hwspecs.rxdesc_read,
2053 malo_bar0_read4(sc, sc->malo_hwspecs.rxdesc_read),
2054 sc->malo_hwspecs.rxdesc_write,
2055 malo_bar0_read4(sc, sc->malo_hwspecs.rxdesc_write));
2057 readptr = malo_bar0_read4(sc, sc->malo_hwspecs.rxdesc_read);
2058 writeptr = malo_bar0_read4(sc, sc->malo_hwspecs.rxdesc_write);
2059 if (readptr == writeptr)
2062 bf = sc->malo_rxnext;
2063 for (ntodo = malo_rxquota; ntodo > 0 && readptr != writeptr; ntodo--) {
2065 bf = STAILQ_FIRST(&sc->malo_rxbuf);
2069 if (bf->bf_m == NULL) {
2071 * If data allocation failed previously there
2072 * will be no buffer; try again to re-populate it.
2073 * Note the firmware will not advance to the next
2074 * descriptor with a dma buffer so we must mimic
2075 * this or we'll get out of sync.
2077 DPRINTF(sc, MALO_DEBUG_ANY,
2078 "%s: rx buf w/o dma memory\n", __func__);
2079 (void)malo_rxbuf_init(sc, bf);
2082 MALO_RXDESC_SYNC(sc, ds,
2083 BUS_DMASYNC_POSTREAD | BUS_DMASYNC_POSTWRITE);
2084 if (ds->rxcontrol != MALO_RXD_CTRL_DMA_OWN)
2087 readptr = le32toh(ds->physnext);
2090 if (sc->malo_debug & MALO_DEBUG_RECV_DESC)
2091 malo_printrxbuf(bf, 0);
2093 status = ds->status;
2094 if (status & MALO_RXD_STATUS_DECRYPT_ERR_MASK) {
2099 * Sync the data buffer.
2101 len = le16toh(ds->pktlen);
2102 bus_dmamap_sync(sc->malo_dmat, bf->bf_dmamap,
2103 BUS_DMASYNC_POSTREAD);
2105 * The 802.11 header is provided all or in part at the front;
2106 * use it to calculate the true size of the header that we'll
2107 * construct below. We use this to figure out where to copy
2108 * payload prior to constructing the header.
2111 data = mtod(m, uint8_t *);
2112 hdrlen = ieee80211_anyhdrsize(data + sizeof(uint16_t));
2113 off = sizeof(uint16_t) + sizeof(struct ieee80211_frame_addr4);
2116 * Calculate RSSI. XXX wrong
2118 rssi = 2 * ((int) ds->snr - ds->nf); /* NB: .5 dBm */
2122 pktlen = hdrlen + (len - off);
2124 * NB: we know our frame is at least as large as
2125 * IEEE80211_MIN_LEN because there is a 4-address frame at
2126 * the front. Hence there's no need to vet the packet length.
2127 * If the frame in fact is too small it should be discarded
2128 * at the net80211 layer.
2131 /* XXX don't need mbuf, just dma buffer */
2132 mnew = malo_getrxmbuf(sc, bf);
2138 * Attach the dma buffer to the mbuf; malo_rxbuf_init will
2139 * re-setup the rx descriptor using the replacement dma
2140 * buffer we just installed above.
2143 m->m_data += off - hdrlen;
2144 m->m_pkthdr.len = m->m_len = pktlen;
2145 m->m_pkthdr.rcvif = ifp;
2148 * Piece 802.11 header together.
2150 wh = mtod(m, struct ieee80211_qosframe *);
2151 /* NB: don't need to do this sometimes but ... */
2152 /* XXX special case so we can memcpy after m_devget? */
2153 ovbcopy(data + sizeof(uint16_t), wh, hdrlen);
2154 if (IEEE80211_QOS_HAS_SEQ(wh)) {
2155 if (IEEE80211_DIR_DSTODS(wh)) {
2157 struct ieee80211_qosframe_addr4*);
2158 *(uint16_t *)wh4->i_qos = ds->qosctrl;
2160 *(uint16_t *)wh->i_qos = ds->qosctrl;
2163 if (ieee80211_radiotap_active(ic)) {
2164 sc->malo_rx_th.wr_flags = 0;
2165 sc->malo_rx_th.wr_rate = ds->rate;
2166 sc->malo_rx_th.wr_antsignal = rssi;
2167 sc->malo_rx_th.wr_antnoise = ds->nf;
2170 if (IFF_DUMPPKTS_RECV(sc, wh)) {
2171 ieee80211_dump_pkt(ic, mtod(m, caddr_t),
2172 len, ds->rate, rssi);
2178 ni = ieee80211_find_rxnode(ic,
2179 (struct ieee80211_frame_min *)wh);
2181 (void) ieee80211_input(ni, m, rssi, ds->nf);
2182 ieee80211_free_node(ni);
2184 (void) ieee80211_input_all(ic, m, rssi, ds->nf);
2186 /* NB: ignore ENOMEM so we process more descriptors */
2187 (void) malo_rxbuf_init(sc, bf);
2188 bf = STAILQ_NEXT(bf, bf_list);
2191 malo_bar0_write4(sc, sc->malo_hwspecs.rxdesc_read, readptr);
2192 sc->malo_rxnext = bf;
2194 if ((ifp->if_drv_flags & IFF_DRV_OACTIVE) == 0 &&
2195 !IFQ_IS_EMPTY(&ifp->if_snd))
2197 #undef IEEE80211_DIR_DSTODS
2201 malo_stop(struct ifnet *ifp, int disable)
2203 struct malo_softc *sc = ifp->if_softc;
2206 malo_stop_locked(ifp, disable);
2211 * Reclaim all tx queue resources.
2214 malo_tx_cleanup(struct malo_softc *sc)
2218 for (i = 0; i < MALO_NUM_TX_QUEUES; i++)
2219 malo_tx_cleanupq(sc, &sc->malo_txq[i]);
2223 malo_detach(struct malo_softc *sc)
2225 struct ifnet *ifp = sc->malo_ifp;
2226 struct ieee80211com *ic = ifp->if_l2com;
2228 DPRINTF(sc, MALO_DEBUG_ANY, "%s: if_flags %x\n",
2229 __func__, ifp->if_flags);
2233 if (sc->malo_tq != NULL) {
2234 taskqueue_drain(sc->malo_tq, &sc->malo_rxtask);
2235 taskqueue_drain(sc->malo_tq, &sc->malo_txtask);
2236 taskqueue_free(sc->malo_tq);
2241 * NB: the order of these is important:
2242 * o call the 802.11 layer before detaching the hal to
2243 * insure callbacks into the driver to delete global
2244 * key cache entries can be handled
2245 * o reclaim the tx queue data structures after calling
2246 * the 802.11 layer as we'll get called back to reclaim
2247 * node state and potentially want to use them
2248 * o to cleanup the tx queues the hal is called, so detach
2250 * Other than that, it's straightforward...
2252 ieee80211_ifdetach(ic);
2253 callout_drain(&sc->malo_watchdog_timer);
2254 malo_dma_cleanup(sc);
2255 malo_tx_cleanup(sc);
2256 malo_hal_detach(sc->malo_mh);
2259 MALO_LOCK_DESTROY(sc);
2265 malo_shutdown(struct malo_softc *sc)
2267 malo_stop(sc->malo_ifp, 1);
2271 malo_suspend(struct malo_softc *sc)
2273 struct ifnet *ifp = sc->malo_ifp;
2275 DPRINTF(sc, MALO_DEBUG_ANY, "%s: if_flags %x\n",
2276 __func__, ifp->if_flags);
2282 malo_resume(struct malo_softc *sc)
2284 struct ifnet *ifp = sc->malo_ifp;
2286 DPRINTF(sc, MALO_DEBUG_ANY, "%s: if_flags %x\n",
2287 __func__, ifp->if_flags);
2289 if (ifp->if_flags & IFF_UP)