]> CyberLeo.Net >> Repos - FreeBSD/stable/10.git/blob - sys/dev/mpt/mpt.h
MFC r368207,368607:
[FreeBSD/stable/10.git] / sys / dev / mpt / mpt.h
1 /* $FreeBSD$ */
2 /*-
3  * Generic defines for LSI '909 FC  adapters.
4  * FreeBSD Version.
5  *
6  * Copyright (c)  2000, 2001 by Greg Ansley
7  *
8  * Redistribution and use in source and binary forms, with or without
9  * modification, are permitted provided that the following conditions
10  * are met:
11  * 1. Redistributions of source code must retain the above copyright
12  *    notice immediately at the beginning of the file, without modification,
13  *    this list of conditions, and the following disclaimer.
14  * 2. The name of the author may not be used to endorse or promote products
15  *    derived from this software without specific prior written permission.
16  *
17  * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
18  * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
19  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
20  * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
21  * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
22  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
23  * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
24  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
25  * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
26  * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
27  * SUCH DAMAGE.
28  */
29 /*-
30  * Copyright (c) 2002, 2006 by Matthew Jacob
31  * All rights reserved.
32  * 
33  * Redistribution and use in source and binary forms, with or without
34  * modification, are permitted provided that the following conditions are
35  * met:
36  * 1. Redistributions of source code must retain the above copyright
37  *    notice, this list of conditions and the following disclaimer.
38  * 2. Redistributions in binary form must reproduce at minimum a disclaimer
39  *    substantially similar to the "NO WARRANTY" disclaimer below
40  *    ("Disclaimer") and any redistribution must be conditioned upon including
41  *    a substantially similar Disclaimer requirement for further binary
42  *    redistribution.
43  * 3. Neither the names of the above listed copyright holders nor the names
44  *    of any contributors may be used to endorse or promote products derived
45  *    from this software without specific prior written permission.
46  * 
47  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
48  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
49  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
50  * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
51  * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
52  * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
53  * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
54  * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
55  * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
56  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF THE COPYRIGHT
57  * OWNER OR CONTRIBUTOR IS ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
58  *
59  * Support from Chris Ellsworth in order to make SAS adapters work
60  * is gratefully acknowledged.
61  *
62  *
63  * Support from LSI-Logic has also gone a great deal toward making this a
64  * workable subsystem and is gratefully acknowledged.
65  */
66 /*
67  * Copyright (c) 2004, Avid Technology, Inc. and its contributors.
68  * Copyright (c) 2004, 2005 Justin T. Gibbs
69  * Copyright (c) 2005, WHEEL Sp. z o.o.
70  * All rights reserved.
71  * 
72  * Redistribution and use in source and binary forms, with or without
73  * modification, are permitted provided that the following conditions are
74  * met:
75  * 1. Redistributions of source code must retain the above copyright
76  *    notice, this list of conditions and the following disclaimer.
77  * 2. Redistributions in binary form must reproduce at minimum a disclaimer
78  *    substantially similar to the "NO WARRANTY" disclaimer below
79  *    ("Disclaimer") and any redistribution must be conditioned upon including
80  *    a substantially similar Disclaimer requirement for further binary
81  *    redistribution.
82  * 3. Neither the names of the above listed copyright holders nor the names
83  *    of any contributors may be used to endorse or promote products derived
84  *    from this software without specific prior written permission.
85  * 
86  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
87  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
88  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
89  * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
90  * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
91  * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
92  * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
93  * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
94  * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
95  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF THE COPYRIGHT
96  * OWNER OR CONTRIBUTOR IS ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
97  */
98
99 #ifndef _MPT_H_
100 #define _MPT_H_
101
102 /********************************* OS Includes ********************************/
103 #include <sys/param.h>
104 #include <sys/systm.h>
105 #include <sys/bus.h>
106 #include <sys/condvar.h>
107 #include <sys/endian.h>
108 #include <sys/eventhandler.h>
109 #include <sys/kernel.h>
110 #include <sys/lock.h>
111 #include <sys/malloc.h>
112 #include <sys/module.h>
113 #include <sys/mutex.h>
114 #include <sys/proc.h>
115 #include <sys/queue.h>
116 #include <sys/rman.h>
117 #include <sys/types.h>
118
119 #include <machine/bus.h>
120 #include <machine/cpu.h>
121 #include <machine/resource.h>
122
123 #ifdef __sparc64__
124 #include <dev/ofw/openfirm.h>
125 #include <machine/ofw_machdep.h>
126 #endif
127
128 #include <dev/pci/pcireg.h>
129 #include <dev/pci/pcivar.h>
130
131 #include "opt_ddb.h"
132
133 /**************************** Register Definitions ****************************/
134 #include <dev/mpt/mpt_reg.h>
135
136 /******************************* MPI Definitions ******************************/
137 #include <dev/mpt/mpilib/mpi_type.h>
138 #include <dev/mpt/mpilib/mpi.h>
139 #include <dev/mpt/mpilib/mpi_cnfg.h>
140 #include <dev/mpt/mpilib/mpi_ioc.h>
141 #include <dev/mpt/mpilib/mpi_raid.h>
142
143 /* XXX For mpt_debug.c */
144 #include <dev/mpt/mpilib/mpi_init.h>
145
146 #define MPT_S64_2_SCALAR(y)     ((((int64_t)y.High) << 32) | (y.Low))
147 #define MPT_U64_2_SCALAR(y)     ((((uint64_t)y.High) << 32) | (y.Low))
148
149 /****************************** Misc Definitions ******************************/
150 /* #define MPT_TEST_MULTIPATH   1 */
151 #define MPT_OK (0)
152 #define MPT_FAIL (0x10000)
153
154 #define NUM_ELEMENTS(array) (sizeof(array) / sizeof(*array))
155
156 #define MPT_ROLE_NONE           0
157 #define MPT_ROLE_INITIATOR      1
158 #define MPT_ROLE_TARGET         2
159 #define MPT_ROLE_BOTH           3
160 #define MPT_ROLE_DEFAULT        MPT_ROLE_INITIATOR
161
162 #define MPT_INI_ID_NONE         -1
163
164 /**************************** Forward Declarations ****************************/
165 struct mpt_softc;
166 struct mpt_personality;
167 typedef struct req_entry request_t;
168
169 /************************* Personality Module Support *************************/
170 typedef int mpt_load_handler_t(struct mpt_personality *);
171 typedef int mpt_probe_handler_t(struct mpt_softc *);
172 typedef int mpt_attach_handler_t(struct mpt_softc *);
173 typedef int mpt_enable_handler_t(struct mpt_softc *);
174 typedef void mpt_ready_handler_t(struct mpt_softc *);
175 typedef int mpt_event_handler_t(struct mpt_softc *, request_t *,
176                                 MSG_EVENT_NOTIFY_REPLY *);
177 typedef void mpt_reset_handler_t(struct mpt_softc *, int /*type*/);
178 /* XXX Add return value and use for veto? */
179 typedef void mpt_shutdown_handler_t(struct mpt_softc *);
180 typedef void mpt_detach_handler_t(struct mpt_softc *);
181 typedef int mpt_unload_handler_t(struct mpt_personality *);
182
183 struct mpt_personality
184 {
185         const char              *name;
186         uint32_t                 id;            /* Assigned identifier. */
187         u_int                    use_count;     /* Instances using personality*/
188         mpt_load_handler_t      *load;          /* configure personailty */
189 #define MPT_PERS_FIRST_HANDLER(pers) (&(pers)->load)
190         mpt_probe_handler_t     *probe;         /* configure personailty */
191         mpt_attach_handler_t    *attach;        /* initialize device instance */
192         mpt_enable_handler_t    *enable;        /* enable device */
193         mpt_ready_handler_t     *ready;         /* final open for business */
194         mpt_event_handler_t     *event;         /* Handle MPI event. */
195         mpt_reset_handler_t     *reset;         /* Re-init after reset. */
196         mpt_shutdown_handler_t  *shutdown;      /* Shutdown instance. */
197         mpt_detach_handler_t    *detach;        /* release device instance */
198         mpt_unload_handler_t    *unload;        /* Shutdown personality */
199 #define MPT_PERS_LAST_HANDLER(pers) (&(pers)->unload)
200 };
201
202 int mpt_modevent(module_t, int, void *);
203
204 /* Maximum supported number of personalities. */
205 #define MPT_MAX_PERSONALITIES   (15)
206
207 #define MPT_PERSONALITY_DEPEND(name, dep, vmin, vpref, vmax) \
208         MODULE_DEPEND(name, dep, vmin, vpref, vmax)
209
210 #define DECLARE_MPT_PERSONALITY(name, order)                              \
211         static moduledata_t name##_mod = {                                \
212                 #name, mpt_modevent, &name##_personality                  \
213         };                                                                \
214         DECLARE_MODULE(name, name##_mod, SI_SUB_DRIVERS, order);          \
215         MODULE_VERSION(name, 1);                                          \
216         MPT_PERSONALITY_DEPEND(name, mpt_core, 1, 1, 1)
217
218 /******************************* Bus DMA Support ******************************/
219 /* XXX Need to update bus_dmamap_sync to take a range argument. */
220 #define bus_dmamap_sync_range(dma_tag, dmamap, offset, len, op) \
221         bus_dmamap_sync(dma_tag, dmamap, op)
222
223 #define mpt_dma_tag_create(mpt, parent_tag, alignment, boundary,        \
224                            lowaddr, highaddr, filter, filterarg,        \
225                            maxsize, nsegments, maxsegsz, flags,         \
226                            dma_tagp)                                    \
227         bus_dma_tag_create(parent_tag, alignment, boundary,             \
228                            lowaddr, highaddr, filter, filterarg,        \
229                            maxsize, nsegments, maxsegsz, flags,         \
230                            busdma_lock_mutex, &(mpt)->mpt_lock,         \
231                            dma_tagp)
232 struct mpt_map_info {
233         struct mpt_softc *mpt;
234         int               error;
235         uint32_t          phys;
236 };
237
238 void mpt_map_rquest(void *, bus_dma_segment_t *, int, int);
239
240 /********************************** Endianess *********************************/
241 #define MPT_2_HOST64(ptr, tag)  ptr->tag = le64toh(ptr->tag)
242 #define MPT_2_HOST32(ptr, tag)  ptr->tag = le32toh(ptr->tag)
243 #define MPT_2_HOST16(ptr, tag)  ptr->tag = le16toh(ptr->tag)
244
245 #define HOST_2_MPT64(ptr, tag)  ptr->tag = htole64(ptr->tag)
246 #define HOST_2_MPT32(ptr, tag)  ptr->tag = htole32(ptr->tag)
247 #define HOST_2_MPT16(ptr, tag)  ptr->tag = htole16(ptr->tag)
248
249 #if     _BYTE_ORDER == _BIG_ENDIAN
250 void mpt2host_sge_simple_union(SGE_SIMPLE_UNION *);
251 void mpt2host_iocfacts_reply(MSG_IOC_FACTS_REPLY *);
252 void mpt2host_portfacts_reply(MSG_PORT_FACTS_REPLY *);
253 void mpt2host_config_page_ioc2(CONFIG_PAGE_IOC_2 *);
254 void mpt2host_config_page_ioc3(CONFIG_PAGE_IOC_3 *);
255 void mpt2host_config_page_scsi_port_0(CONFIG_PAGE_SCSI_PORT_0 *);
256 void mpt2host_config_page_scsi_port_1(CONFIG_PAGE_SCSI_PORT_1 *);
257 void host2mpt_config_page_scsi_port_1(CONFIG_PAGE_SCSI_PORT_1 *);
258 void mpt2host_config_page_scsi_port_2(CONFIG_PAGE_SCSI_PORT_2 *);
259 void mpt2host_config_page_scsi_device_0(CONFIG_PAGE_SCSI_DEVICE_0 *);
260 void mpt2host_config_page_scsi_device_1(CONFIG_PAGE_SCSI_DEVICE_1 *);
261 void host2mpt_config_page_scsi_device_1(CONFIG_PAGE_SCSI_DEVICE_1 *);
262 void mpt2host_config_page_fc_port_0(CONFIG_PAGE_FC_PORT_0 *);
263 void mpt2host_config_page_fc_port_1(CONFIG_PAGE_FC_PORT_1 *);
264 void host2mpt_config_page_fc_port_1(CONFIG_PAGE_FC_PORT_1 *);
265 void mpt2host_config_page_raid_vol_0(CONFIG_PAGE_RAID_VOL_0 *);
266 void mpt2host_config_page_raid_phys_disk_0(CONFIG_PAGE_RAID_PHYS_DISK_0 *);
267 void mpt2host_mpi_raid_vol_indicator(MPI_RAID_VOL_INDICATOR *);
268 #else
269 #define mpt2host_sge_simple_union(x)            do { ; } while (0)
270 #define mpt2host_iocfacts_reply(x)              do { ; } while (0)
271 #define mpt2host_portfacts_reply(x)             do { ; } while (0)
272 #define mpt2host_config_page_ioc2(x)            do { ; } while (0)
273 #define mpt2host_config_page_ioc3(x)            do { ; } while (0)
274 #define mpt2host_config_page_scsi_port_0(x)     do { ; } while (0)
275 #define mpt2host_config_page_scsi_port_1(x)     do { ; } while (0)
276 #define host2mpt_config_page_scsi_port_1(x)     do { ; } while (0)
277 #define mpt2host_config_page_scsi_port_2(x)     do { ; } while (0)
278 #define mpt2host_config_page_scsi_device_0(x)   do { ; } while (0)
279 #define mpt2host_config_page_scsi_device_1(x)   do { ; } while (0)
280 #define host2mpt_config_page_scsi_device_1(x)   do { ; } while (0)
281 #define mpt2host_config_page_fc_port_0(x)       do { ; } while (0)
282 #define mpt2host_config_page_fc_port_1(x)       do { ; } while (0)
283 #define host2mpt_config_page_fc_port_1(x)       do { ; } while (0)
284 #define mpt2host_config_page_raid_vol_0(x)      do { ; } while (0)
285 #define mpt2host_config_page_raid_phys_disk_0(x)                        \
286         do { ; } while (0)
287 #define mpt2host_mpi_raid_vol_indicator(x)      do { ; } while (0)
288 #endif
289
290 /**************************** MPI Transaction State ***************************/
291 typedef enum {
292         REQ_STATE_NIL           = 0x00,
293         REQ_STATE_FREE          = 0x01,
294         REQ_STATE_ALLOCATED     = 0x02,
295         REQ_STATE_QUEUED        = 0x04,
296         REQ_STATE_DONE          = 0x08,
297         REQ_STATE_TIMEDOUT      = 0x10,
298         REQ_STATE_NEED_WAKEUP   = 0x20,
299         REQ_STATE_LOCKED        = 0x80, /* can't be freed */
300         REQ_STATE_MASK          = 0xFF
301 } mpt_req_state_t; 
302
303 struct req_entry {
304         TAILQ_ENTRY(req_entry) links;   /* Pointer to next in list */
305         mpt_req_state_t state;          /* Request State Information */
306         uint16_t        index;          /* Index of this entry */
307         uint16_t        IOCStatus;      /* Completion status */
308         uint16_t        ResponseCode;   /* TMF Response Code */
309         uint16_t        serno;          /* serial number */
310         union ccb      *ccb;            /* CAM request */
311         void           *req_vbuf;       /* Virtual Address of Entry */
312         void           *sense_vbuf;     /* Virtual Address of sense data */
313         bus_addr_t      req_pbuf;       /* Physical Address of Entry */
314         bus_addr_t      sense_pbuf;     /* Physical Address of sense data */
315         bus_dmamap_t    dmap;           /* DMA map for data buffers */
316         struct req_entry *chain;        /* for SGE overallocations */
317         struct callout  callout;        /* Timeout for the request */
318 };
319
320 typedef struct mpt_config_params {
321         u_int           Action;
322         u_int           PageVersion;
323         u_int           PageLength;
324         u_int           PageNumber;
325         u_int           PageType;
326         u_int           PageAddress;
327         u_int           ExtPageLength;
328         u_int           ExtPageType;
329 } cfgparms_t;
330
331 /**************************** MPI Target State Info ***************************/
332 typedef struct {
333         uint32_t reply_desc;    /* current reply descriptor */
334         uint32_t bytes_xfered;  /* current relative offset */
335         int resid;              /* current data residual */
336         union ccb *ccb;         /* pointer to currently active ccb */
337         request_t *req;         /* pointer to currently active assist request */
338         uint32_t
339                 is_local : 1,
340                 nxfers   : 31;
341         uint32_t tag_id;        /* Our local tag. */
342         uint16_t itag;          /* Initiator tag. */
343         enum {
344                 TGT_STATE_NIL,
345                 TGT_STATE_LOADING,
346                 TGT_STATE_LOADED,
347                 TGT_STATE_IN_CAM,
348                 TGT_STATE_SETTING_UP_FOR_DATA,
349                 TGT_STATE_MOVING_DATA,
350                 TGT_STATE_MOVING_DATA_AND_STATUS,
351                 TGT_STATE_SENDING_STATUS
352         } state;
353 } mpt_tgt_state_t;
354
355 /*
356  * When we get an incoming command it has its own tag which is called the
357  * IoIndex. This is the value we gave that particular command buffer when
358  * we originally assigned it. It's just a number, really. The FC card uses
359  * it as an RX_ID. We can use it to index into mpt->tgt_cmd_ptrs, which
360  * contains pointers the request_t structures related to that IoIndex.
361  *
362  * What *we* do is construct a tag out of the index for the target command
363  * which owns the incoming ATIO plus a rolling sequence number.
364  */
365 #define MPT_MAKE_TAGID(mpt, req, ioindex)       \
366  ((ioindex << 18) | (((mpt->sequence++) & 0x3f) << 12) | (req->index & 0xfff))
367
368 #ifdef  INVARIANTS
369 #define MPT_TAG_2_REQ(a, b)             mpt_tag_2_req(a, (uint32_t) b)
370 #else
371 #define MPT_TAG_2_REQ(mpt, tag)         mpt->tgt_cmd_ptrs[tag >> 18]
372 #endif
373
374 #define MPT_TGT_STATE(mpt, req) ((mpt_tgt_state_t *) \
375     (&((uint8_t *)req->req_vbuf)[MPT_RQSL(mpt) - sizeof (mpt_tgt_state_t)]))
376
377 STAILQ_HEAD(mpt_hdr_stailq, ccb_hdr);
378 #define MPT_MAX_LUNS    256
379 typedef struct {
380         struct mpt_hdr_stailq   atios;
381         struct mpt_hdr_stailq   inots;
382         int enabled;
383 } tgt_resource_t;
384 #define MPT_MAX_ELS     64
385
386 /**************************** Handler Registration ****************************/
387 /*
388  * Global table of registered reply handlers.  The
389  * handler is indicated by byte 3 of the request
390  * index submitted to the IOC.  This allows the
391  * driver core to perform generic processing without
392  * any knowledge of per-personality behavior.
393  *
394  * MPT_NUM_REPLY_HANDLERS must be a power of 2
395  * to allow the easy generation of a mask.
396  *
397  * The handler offsets used by the core are hard coded
398  * allowing faster code generation when assigning a handler
399  * to a request.  All "personalities" must use the
400  * the handler registration mechanism.
401  *
402  * The IOC handlers that are rarely executed are placed
403  * at the tail of the table to make it more likely that
404  * all commonly executed handlers fit in a single cache
405  * line.
406  */
407 #define MPT_NUM_REPLY_HANDLERS          (32)
408 #define MPT_REPLY_HANDLER_EVENTS        MPT_CBI_TO_HID(0)
409 #define MPT_REPLY_HANDLER_CONFIG        MPT_CBI_TO_HID(MPT_NUM_REPLY_HANDLERS-1)
410 #define MPT_REPLY_HANDLER_HANDSHAKE     MPT_CBI_TO_HID(MPT_NUM_REPLY_HANDLERS-2)
411 typedef int mpt_reply_handler_t(struct mpt_softc *mpt, request_t *request,
412     uint32_t reply_desc, MSG_DEFAULT_REPLY *reply_frame);
413 typedef union {
414         mpt_reply_handler_t     *reply_handler;
415 } mpt_handler_t;
416
417 typedef enum {
418         MPT_HANDLER_REPLY,
419         MPT_HANDLER_EVENT,
420         MPT_HANDLER_RESET,
421         MPT_HANDLER_SHUTDOWN
422 } mpt_handler_type;
423
424 struct mpt_handler_record
425 {
426         LIST_ENTRY(mpt_handler_record)  links;
427         mpt_handler_t                   handler;
428 };
429
430 LIST_HEAD(mpt_handler_list, mpt_handler_record);
431
432 /*
433  * The handler_id is currently unused but would contain the
434  * handler ID used in the MsgContext field to allow direction
435  * of replies to the handler.  Registrations that don't require
436  * a handler id can pass in NULL for the handler_id.
437  *
438  * Deregistrations for handlers without a handler id should
439  * pass in MPT_HANDLER_ID_NONE.
440  */
441 #define MPT_HANDLER_ID_NONE             (0xFFFFFFFF)
442 int mpt_register_handler(struct mpt_softc *, mpt_handler_type,
443                          mpt_handler_t, uint32_t *);
444 int mpt_deregister_handler(struct mpt_softc *, mpt_handler_type,
445                            mpt_handler_t, uint32_t);
446
447 /******************* Per-Controller Instance Data Structures ******************/
448 TAILQ_HEAD(req_queue, req_entry);
449
450 /* Structure for saving proper values for modifyable PCI config registers */
451 struct mpt_pci_cfg {
452         uint16_t Command;
453         uint16_t LatencyTimer_LineSize;
454         uint32_t IO_BAR;
455         uint32_t Mem0_BAR[2];
456         uint32_t Mem1_BAR[2];
457         uint32_t ROM_BAR;
458         uint8_t  IntLine;
459         uint32_t PMCSR;
460 };
461
462 typedef enum {
463         MPT_RVF_NONE            = 0x0,
464         MPT_RVF_ACTIVE          = 0x1,
465         MPT_RVF_ANNOUNCED       = 0x2,
466         MPT_RVF_UP2DATE         = 0x4,
467         MPT_RVF_REFERENCED      = 0x8,
468         MPT_RVF_WCE_CHANGED     = 0x10
469 } mpt_raid_volume_flags;
470
471 struct mpt_raid_volume {
472         CONFIG_PAGE_RAID_VOL_0         *config_page;
473         MPI_RAID_VOL_INDICATOR          sync_progress;
474         mpt_raid_volume_flags           flags;
475         u_int                           quiesced_disks;
476 };
477
478 typedef enum {
479         MPT_RDF_NONE            = 0x00,
480         MPT_RDF_ACTIVE          = 0x01,
481         MPT_RDF_ANNOUNCED       = 0x02,
482         MPT_RDF_UP2DATE         = 0x04,
483         MPT_RDF_REFERENCED      = 0x08,
484         MPT_RDF_QUIESCING       = 0x10,
485         MPT_RDF_QUIESCED        = 0x20
486 } mpt_raid_disk_flags;
487
488 struct mpt_raid_disk {
489         CONFIG_PAGE_RAID_PHYS_DISK_0    config_page;
490         struct mpt_raid_volume         *volume;
491         u_int                           member_number;
492         u_int                           pass_thru_active;
493         mpt_raid_disk_flags             flags;
494 };
495
496 struct mpt_evtf_record {
497         MSG_EVENT_NOTIFY_REPLY          reply;
498         uint32_t                        context;
499         LIST_ENTRY(mpt_evtf_record)     links;
500 };
501
502 LIST_HEAD(mpt_evtf_list, mpt_evtf_record);
503
504 struct mptsas_devinfo {
505         uint16_t        dev_handle;
506         uint16_t        parent_dev_handle;
507         uint16_t        enclosure_handle;
508         uint16_t        slot;
509         uint8_t         phy_num;
510         uint8_t         physical_port;
511         uint8_t         target_id;
512         uint8_t         bus;
513         uint64_t        sas_address;
514         uint32_t        device_info;
515 };
516
517 struct mptsas_phyinfo {
518         uint16_t        handle;
519         uint8_t         phy_num;
520         uint8_t         port_id;
521         uint8_t         negotiated_link_rate;
522         uint8_t         hw_link_rate;
523         uint8_t         programmed_link_rate;
524         uint8_t         sas_port_add_phy;
525         struct mptsas_devinfo identify;
526         struct mptsas_devinfo attached;
527 };
528
529 struct mptsas_portinfo {
530         uint16_t                        num_phys;
531         struct mptsas_phyinfo           *phy_info;
532 };
533
534 struct mpt_softc {
535         device_t                dev;
536         struct mtx              mpt_lock;
537         int                     mpt_locksetup;
538         uint32_t                mpt_pers_mask;
539         uint32_t
540                                 : 7,
541                 unit            : 8,
542                 ready           : 1,
543                 fw_uploaded     : 1,
544                 msi_enable      : 1,
545                 twildcard       : 1,
546                 tenabled        : 1,
547                 do_cfg_role     : 1,
548                 raid_enabled    : 1,
549                 raid_mwce_set   : 1,
550                 getreqwaiter    : 1,
551                 shutdwn_raid    : 1,
552                 shutdwn_recovery: 1,
553                 outofbeer       : 1,
554                 disabled        : 1,
555                 is_spi          : 1,
556                 is_sas          : 1,
557                 is_fc           : 1,
558                 is_1078         : 1;
559
560         u_int                   cfg_role;
561         u_int                   role;   /* role: none, ini, target, both */
562
563         u_int                   verbose;
564 #ifdef  MPT_TEST_MULTIPATH
565         int                     failure_id;
566 #endif
567
568         /*
569          * IOC Facts
570          */
571         MSG_IOC_FACTS_REPLY     ioc_facts;
572
573         /*
574          * Port Facts
575          */
576         MSG_PORT_FACTS_REPLY *  port_facts;
577 #define mpt_max_tgtcmds port_facts[0].MaxPostedCmdBuffers
578
579         /*
580          * Device Configuration Information
581          */
582         union {
583                 struct mpt_spi_cfg {
584                         CONFIG_PAGE_SCSI_PORT_0         _port_page0;
585                         CONFIG_PAGE_SCSI_PORT_1         _port_page1;
586                         CONFIG_PAGE_SCSI_PORT_2         _port_page2;
587                         CONFIG_PAGE_SCSI_DEVICE_0       _dev_page0[16];
588                         CONFIG_PAGE_SCSI_DEVICE_1       _dev_page1[16];
589                         int                             _ini_id;
590                         uint16_t                        _tag_enable;
591                         uint16_t                        _disc_enable;
592                 } spi;
593 #define mpt_port_page0          cfg.spi._port_page0
594 #define mpt_port_page1          cfg.spi._port_page1
595 #define mpt_port_page2          cfg.spi._port_page2
596 #define mpt_dev_page0           cfg.spi._dev_page0
597 #define mpt_dev_page1           cfg.spi._dev_page1
598 #define mpt_ini_id              cfg.spi._ini_id
599 #define mpt_tag_enable          cfg.spi._tag_enable
600 #define mpt_disc_enable         cfg.spi._disc_enable
601                 struct mpi_fc_cfg {
602                         CONFIG_PAGE_FC_PORT_0 _port_page0;
603                         uint32_t _port_speed;
604 #define mpt_fcport_page0        cfg.fc._port_page0
605 #define mpt_fcport_speed        cfg.fc._port_speed
606                 } fc;
607         } cfg;
608         /*
609          * Device config information stored up for sysctl to access
610          */
611         union {
612                 struct {
613                         unsigned int initiator_id;
614                 } spi;
615                 struct {
616                         uint64_t wwnn;
617                         uint64_t wwpn;
618                         uint32_t portid;
619                 } fc;
620         } scinfo;
621
622         /* Controller Info for RAID information */
623         CONFIG_PAGE_IOC_2 *     ioc_page2;
624         CONFIG_PAGE_IOC_3 *     ioc_page3;
625
626         /* Raid Data */
627         struct mpt_raid_volume* raid_volumes;
628         struct mpt_raid_disk*   raid_disks;
629         u_int                   raid_max_volumes;
630         u_int                   raid_max_disks;
631         u_int                   raid_page0_len;
632         u_int                   raid_wakeup;
633         u_int                   raid_rescan;
634         u_int                   raid_resync_rate;
635         u_int                   raid_mwce_setting;
636         u_int                   raid_queue_depth;
637         u_int                   raid_nonopt_volumes;
638         struct proc            *raid_thread;
639         struct callout          raid_timer;
640
641         /*
642          * PCI Hardware info
643          */
644         struct resource *       pci_irq;        /* Interrupt map for chip */
645         void *                  ih;             /* Interrupt handle */
646 #if 0
647         struct mpt_pci_cfg      pci_cfg;        /* saved PCI conf registers */
648 #endif
649
650         /*
651          * DMA Mapping Stuff
652          */
653         struct resource *       pci_reg;        /* Register map for chip */
654         bus_space_tag_t         pci_st;         /* Bus tag for registers */
655         bus_space_handle_t      pci_sh;         /* Bus handle for registers */
656         /* PIO versions of above. */
657         struct resource *       pci_pio_reg;
658         bus_space_tag_t         pci_pio_st;
659         bus_space_handle_t      pci_pio_sh;
660
661         bus_dma_tag_t           parent_dmat;    /* DMA tag for parent PCI bus */
662         bus_dma_tag_t           reply_dmat;     /* DMA tag for reply memory */
663         bus_dmamap_t            reply_dmap;     /* DMA map for reply memory */
664         uint8_t                *reply;          /* KVA of reply memory */
665         bus_addr_t              reply_phys;     /* BusAddr of reply memory */
666
667         bus_dma_tag_t           buffer_dmat;    /* DMA tag for buffers */
668         bus_dma_tag_t           request_dmat;   /* DMA tag for request memroy */
669         bus_dmamap_t            request_dmap;   /* DMA map for request memroy */
670         uint8_t                *request;        /* KVA of Request memory */
671         bus_addr_t              request_phys;   /* BusAddr of request memory */
672
673         uint32_t                max_seg_cnt;    /* calculated after IOC facts */
674         uint32_t                max_cam_seg_cnt;/* calculated from MAXPHYS*/
675
676         /*
677          * Hardware management
678          */
679         u_int                   reset_cnt;
680
681         /*
682          * CAM && Software Management
683          */
684         request_t              *request_pool;
685         struct req_queue        request_free_list;
686         struct req_queue        request_pending_list;
687         struct req_queue        request_timeout_list;
688
689
690         struct cam_sim         *sim;
691         struct cam_path        *path;
692
693         struct cam_sim         *phydisk_sim;
694         struct cam_path        *phydisk_path;
695
696         struct proc            *recovery_thread;
697         request_t              *tmf_req;
698
699         /*
700          * Deferred frame acks due to resource shortage.
701          */
702         struct mpt_evtf_list    ack_frames;
703
704         /*
705          * Target Mode Support
706          */
707         uint32_t                scsi_tgt_handler_id;
708         request_t **            tgt_cmd_ptrs;
709         request_t **            els_cmd_ptrs;   /* FC only */
710
711         /*
712          * *snork*- this is chosen to be here *just in case* somebody
713          * forgets to point to it exactly and we index off of trt with
714          * CAM_LUN_WILDCARD.
715          */
716         tgt_resource_t          trt_wildcard;           /* wildcard luns */
717         tgt_resource_t          trt[MPT_MAX_LUNS];
718         uint16_t                tgt_cmds_allocated;
719         uint16_t                els_cmds_allocated;     /* FC only */
720
721         uint16_t                timeouts;       /* timeout count */
722         uint16_t                success;        /* successes afer timeout */
723         uint16_t                sequence;       /* Sequence Number */
724         uint16_t                pad3;
725
726 #if 0
727         /* Paired port in some dual adapters configurations */
728         struct mpt_softc *      mpt2;
729 #endif
730
731         /* FW Image management */
732         uint32_t                fw_image_size;
733         uint8_t                *fw_image;
734         bus_dma_tag_t           fw_dmat;        /* DMA tag for firmware image */
735         bus_dmamap_t            fw_dmap;        /* DMA map for firmware image */
736         bus_addr_t              fw_phys;        /* BusAddr of firmware image */
737
738         /* SAS Topology */
739         struct mptsas_portinfo  *sas_portinfo;
740
741         /* Shutdown Event Handler. */
742         eventhandler_tag         eh;
743
744         /* Userland management interface. */
745         struct cdev             *cdev;
746
747         TAILQ_ENTRY(mpt_softc)  links;
748 };
749
750 static __inline void mpt_assign_serno(struct mpt_softc *, request_t *);
751
752 static __inline void
753 mpt_assign_serno(struct mpt_softc *mpt, request_t *req)
754 {
755         if ((req->serno = mpt->sequence++) == 0) {
756                 req->serno = mpt->sequence++;
757         }
758 }
759
760 /***************************** Locking Primitives *****************************/
761 #define MPT_IFLAGS              INTR_TYPE_CAM | INTR_ENTROPY | INTR_MPSAFE
762 #define MPT_LOCK_SETUP(mpt)                                             \
763                 mtx_init(&mpt->mpt_lock, "mpt", NULL, MTX_DEF);         \
764                 mpt->mpt_locksetup = 1
765 #define MPT_LOCK_DESTROY(mpt)                                           \
766         if (mpt->mpt_locksetup) {                                       \
767                 mtx_destroy(&mpt->mpt_lock);                            \
768                 mpt->mpt_locksetup = 0;                                 \
769         }
770
771 #define MPT_LOCK(mpt)           mtx_lock(&(mpt)->mpt_lock)
772 #define MPT_UNLOCK(mpt)         mtx_unlock(&(mpt)->mpt_lock)
773 #define MPT_OWNED(mpt)          mtx_owned(&(mpt)->mpt_lock)
774 #define MPT_LOCK_ASSERT(mpt)    mtx_assert(&(mpt)->mpt_lock, MA_OWNED)
775 #define mpt_sleep(mpt, ident, priority, wmesg, sbt) \
776     msleep_sbt(ident, &(mpt)->mpt_lock, priority, wmesg, sbt, 0, 0)
777 #define mpt_req_timeout(req, sbt, func, arg) \
778     callout_reset_sbt(&(req)->callout, (sbt), 0, (func), (arg), 0)
779 #define mpt_req_untimeout(req, func, arg) \
780         callout_stop(&(req)->callout)
781 #define mpt_callout_init(mpt, c) \
782         callout_init_mtx(c, &(mpt)->mpt_lock, 0)
783 #define mpt_callout_drain(mpt, c) \
784         callout_drain(c)
785
786 /******************************* Register Access ******************************/
787 static __inline void mpt_write(struct mpt_softc *, size_t, uint32_t);
788 static __inline void mpt_write_stream(struct mpt_softc *, size_t, uint32_t);
789 static __inline uint32_t mpt_read(struct mpt_softc *, int);
790 static __inline void mpt_pio_write(struct mpt_softc *, size_t, uint32_t);
791 static __inline uint32_t mpt_pio_read(struct mpt_softc *, int);
792
793 static __inline void
794 mpt_write(struct mpt_softc *mpt, size_t offset, uint32_t val)
795 {
796         bus_space_write_4(mpt->pci_st, mpt->pci_sh, offset, val);
797 }
798
799 static __inline void
800 mpt_write_stream(struct mpt_softc *mpt, size_t offset, uint32_t val)
801 {
802         bus_space_write_stream_4(mpt->pci_st, mpt->pci_sh, offset, val);
803 }
804
805 static __inline uint32_t
806 mpt_read(struct mpt_softc *mpt, int offset)
807 {
808         return (bus_space_read_4(mpt->pci_st, mpt->pci_sh, offset));
809 }
810
811 /*
812  * Some operations (e.g. diagnostic register writes while the ARM proccessor
813  * is disabled), must be performed using "PCI pio" operations.  On non-PCI
814  * busses, these operations likely map to normal register accesses.
815  */
816 static __inline void
817 mpt_pio_write(struct mpt_softc *mpt, size_t offset, uint32_t val)
818 {
819         KASSERT(mpt->pci_pio_reg != NULL, ("no PIO resource"));
820         bus_space_write_4(mpt->pci_pio_st, mpt->pci_pio_sh, offset, val);
821 }
822
823 static __inline uint32_t
824 mpt_pio_read(struct mpt_softc *mpt, int offset)
825 {
826         KASSERT(mpt->pci_pio_reg != NULL, ("no PIO resource"));
827         return (bus_space_read_4(mpt->pci_pio_st, mpt->pci_pio_sh, offset));
828 }
829
830 /*********************** Reply Frame/Request Management ***********************/
831 /* Max MPT Reply we are willing to accept (must be power of 2) */
832 #define MPT_REPLY_SIZE          256
833
834 /*
835  * Must be less than 16384 in order for target mode to work
836  */
837 #define MPT_MAX_REQUESTS(mpt)   512
838 #define MPT_REQUEST_AREA        512
839 #define MPT_SENSE_SIZE          32      /* included in MPT_REQUEST_AREA */
840 #define MPT_REQ_MEM_SIZE(mpt)   (MPT_MAX_REQUESTS(mpt) * MPT_REQUEST_AREA)
841
842 #define MPT_CONTEXT_CB_SHIFT    (16)
843 #define MPT_CBI(handle)         (handle >> MPT_CONTEXT_CB_SHIFT)
844 #define MPT_CBI_TO_HID(cbi)     ((cbi) << MPT_CONTEXT_CB_SHIFT)
845 #define MPT_CONTEXT_TO_CBI(x)   \
846     (((x) >> MPT_CONTEXT_CB_SHIFT) & (MPT_NUM_REPLY_HANDLERS - 1))
847 #define MPT_CONTEXT_REQI_MASK   0xFFFF
848 #define MPT_CONTEXT_TO_REQI(x)  ((x) & MPT_CONTEXT_REQI_MASK)
849
850 /*
851  * Convert a 32bit physical address returned from IOC to an
852  * offset into our reply frame memory or the kvm address needed
853  * to access the data.  The returned address is only the low
854  * 32 bits, so mask our base physical address accordingly.
855  */
856 #define MPT_REPLY_BADDR(x)              \
857         (x << 1)
858 #define MPT_REPLY_OTOV(m, i)            \
859         ((void *)(&m->reply[i]))
860
861 #define MPT_DUMP_REPLY_FRAME(mpt, reply_frame)          \
862 do {                                                    \
863         if (mpt->verbose > MPT_PRT_DEBUG)               \
864                 mpt_dump_reply_frame(mpt, reply_frame); \
865 } while(0)
866
867 static __inline uint32_t mpt_pop_reply_queue(struct mpt_softc *mpt);
868 static __inline void mpt_free_reply(struct mpt_softc *mpt, uint32_t ptr);
869
870 /*
871  * Give the reply buffer back to the IOC after we have
872  * finished processing it.
873  */
874 static __inline void
875 mpt_free_reply(struct mpt_softc *mpt, uint32_t ptr)
876 {
877      mpt_write(mpt, MPT_OFFSET_REPLY_Q, ptr);
878 }
879
880 /* Get a reply from the IOC */
881 static __inline uint32_t
882 mpt_pop_reply_queue(struct mpt_softc *mpt)
883 {
884      return mpt_read(mpt, MPT_OFFSET_REPLY_Q);
885 }
886
887 void
888 mpt_complete_request_chain(struct mpt_softc *, struct req_queue *, u_int);
889
890 /************************** Scatter Gather Management **************************/
891 /* MPT_RQSL- size of request frame, in bytes */
892 #define MPT_RQSL(mpt)           (mpt->ioc_facts.RequestFrameSize << 2)
893
894 /* MPT_NSGL- how many SG entries can fit in a request frame size */
895 #define MPT_NSGL(mpt)           (MPT_RQSL(mpt) / sizeof (SGE_IO_UNION))
896
897 /* MPT_NRFM- how many request frames can fit in each request alloc we make */
898 #define MPT_NRFM(mpt)           (MPT_REQUEST_AREA / MPT_RQSL(mpt))
899
900 /*
901  * MPT_NSGL_FIRST- # of SG elements that can fit after
902  * an I/O request but still within the request frame.
903  * Do this safely based upon SGE_IO_UNION.
904  *
905  * Note that the first element is *within* the SCSI request.
906  */
907 #define MPT_NSGL_FIRST(mpt)     \
908     ((MPT_RQSL(mpt) - sizeof (MSG_SCSI_IO_REQUEST) + sizeof (SGE_IO_UNION)) / \
909     sizeof (SGE_IO_UNION))
910
911 /***************************** IOC Initialization *****************************/
912 int mpt_reset(struct mpt_softc *, int /*reinit*/);
913
914 /****************************** Debugging ************************************/
915 void mpt_dump_data(struct mpt_softc *, const char *, void *, int);
916 void mpt_dump_request(struct mpt_softc *, request_t *);
917
918 enum {
919         MPT_PRT_ALWAYS,
920         MPT_PRT_FATAL,
921         MPT_PRT_ERROR,
922         MPT_PRT_WARN,
923         MPT_PRT_INFO,
924         MPT_PRT_NEGOTIATION,
925         MPT_PRT_DEBUG,
926         MPT_PRT_DEBUG1,
927         MPT_PRT_DEBUG2,
928         MPT_PRT_DEBUG3,
929         MPT_PRT_TRACE,
930         MPT_PRT_NONE=100
931 };
932
933 #define mpt_lprt(mpt, level, ...)               \
934 do {                                            \
935         if (level <= (mpt)->verbose)            \
936                 mpt_prt(mpt, __VA_ARGS__);      \
937 } while (0)
938
939 #if 0
940 #define mpt_lprtc(mpt, level, ...)              \
941 do {                                            \
942         if (level <= (mpt)->verbose)            \
943                 mpt_prtc(mpt, __VA_ARGS__);     \
944 } while (0)
945 #endif
946
947 void mpt_prt(struct mpt_softc *, const char *, ...)
948         __printflike(2, 3);
949 void mpt_prtc(struct mpt_softc *, const char *, ...)
950         __printflike(2, 3);
951
952 /**************************** Target Mode Related ***************************/
953 #ifdef  INVARIANTS
954 static __inline request_t * mpt_tag_2_req(struct mpt_softc *, uint32_t);
955 static __inline request_t *
956 mpt_tag_2_req(struct mpt_softc *mpt, uint32_t tag)
957 {
958         uint16_t rtg = (tag >> 18);
959         KASSERT(rtg < mpt->tgt_cmds_allocated, ("bad tag %d", tag));
960         KASSERT(mpt->tgt_cmd_ptrs, ("no cmd backpointer array"));
961         KASSERT(mpt->tgt_cmd_ptrs[rtg], ("no cmd backpointer"));
962         return (mpt->tgt_cmd_ptrs[rtg]);
963 }
964 #endif
965
966 static __inline int
967 mpt_req_on_free_list(struct mpt_softc *, request_t *);
968 static __inline int
969 mpt_req_on_pending_list(struct mpt_softc *, request_t *);
970
971 /*
972  * Is request on freelist?
973  */
974 static __inline int
975 mpt_req_on_free_list(struct mpt_softc *mpt, request_t *req)
976 {
977         request_t *lrq;
978
979         TAILQ_FOREACH(lrq, &mpt->request_free_list, links) {
980                 if (lrq == req) {
981                         return (1);
982                 }
983         }
984         return (0);
985 }
986
987 /*
988  * Is request on pending list?
989  */
990 static __inline int
991 mpt_req_on_pending_list(struct mpt_softc *mpt, request_t *req)
992 {
993         request_t *lrq;
994
995         TAILQ_FOREACH(lrq, &mpt->request_pending_list, links) {
996                 if (lrq == req) {
997                         return (1);
998                 }
999         }
1000         return (0);
1001 }
1002
1003 #ifdef  INVARIANTS
1004 static __inline void
1005 mpt_req_spcl(struct mpt_softc *, request_t *, const char *, int);
1006 static __inline void
1007 mpt_req_not_spcl(struct mpt_softc *, request_t *, const char *, int);
1008
1009 /*
1010  * Make sure that req *is* part of one of the special lists
1011  */
1012 static __inline void
1013 mpt_req_spcl(struct mpt_softc *mpt, request_t *req, const char *s, int line)
1014 {
1015         int i;
1016         for (i = 0; i < mpt->els_cmds_allocated; i++) {
1017                 if (req == mpt->els_cmd_ptrs[i]) {
1018                         return;
1019                 }
1020         }
1021         for (i = 0; i < mpt->tgt_cmds_allocated; i++) {
1022                 if (req == mpt->tgt_cmd_ptrs[i]) {
1023                         return;
1024                 }
1025         }
1026         panic("%s(%d): req %p:%u function %x not in els or tgt ptrs",
1027             s, line, req, req->serno,
1028             ((PTR_MSG_REQUEST_HEADER)req->req_vbuf)->Function);
1029 }
1030
1031 /*
1032  * Make sure that req is *not* part of one of the special lists.
1033  */
1034 static __inline void
1035 mpt_req_not_spcl(struct mpt_softc *mpt, request_t *req, const char *s, int line)
1036 {
1037         int i;
1038         for (i = 0; i < mpt->els_cmds_allocated; i++) {
1039                 KASSERT(req != mpt->els_cmd_ptrs[i],
1040                     ("%s(%d): req %p:%u func %x in els ptrs at ioindex %d",
1041                     s, line, req, req->serno,
1042                     ((PTR_MSG_REQUEST_HEADER)req->req_vbuf)->Function, i));
1043         }
1044         for (i = 0; i < mpt->tgt_cmds_allocated; i++) {
1045                 KASSERT(req != mpt->tgt_cmd_ptrs[i],
1046                     ("%s(%d): req %p:%u func %x in tgt ptrs at ioindex %d",
1047                     s, line, req, req->serno,
1048                     ((PTR_MSG_REQUEST_HEADER)req->req_vbuf)->Function, i));
1049         }
1050 }
1051 #endif
1052
1053 /*
1054  * Task Management Types, purely for internal consumption
1055  */
1056 typedef enum {
1057         MPT_QUERY_TASK_SET=1234,
1058         MPT_ABORT_TASK_SET,
1059         MPT_CLEAR_TASK_SET,
1060         MPT_QUERY_ASYNC_EVENT,
1061         MPT_LOGICAL_UNIT_RESET,
1062         MPT_TARGET_RESET,
1063         MPT_CLEAR_ACA,
1064         MPT_NIL_TMT_VALUE=5678
1065 } mpt_task_mgmt_t;
1066
1067 /**************************** Unclassified Routines ***************************/
1068 void            mpt_send_cmd(struct mpt_softc *mpt, request_t *req);
1069 int             mpt_recv_handshake_reply(struct mpt_softc *mpt,
1070                                          size_t reply_len, void *reply);
1071 int             mpt_wait_req(struct mpt_softc *mpt, request_t *req,
1072                              mpt_req_state_t state, mpt_req_state_t mask,
1073                              int sleep_ok, int time_ms);
1074 void            mpt_enable_ints(struct mpt_softc *mpt);
1075 void            mpt_disable_ints(struct mpt_softc *mpt);
1076 int             mpt_attach(struct mpt_softc *mpt);
1077 int             mpt_shutdown(struct mpt_softc *mpt);
1078 int             mpt_detach(struct mpt_softc *mpt);
1079 int             mpt_send_handshake_cmd(struct mpt_softc *mpt,
1080                                        size_t len, void *cmd);
1081 request_t *     mpt_get_request(struct mpt_softc *mpt, int sleep_ok);
1082 void            mpt_free_request(struct mpt_softc *mpt, request_t *req);
1083 void            mpt_intr(void *arg);
1084 void            mpt_check_doorbell(struct mpt_softc *mpt);
1085 void            mpt_dump_reply_frame(struct mpt_softc *mpt,
1086                                      MSG_DEFAULT_REPLY *reply_frame);
1087
1088 int             mpt_issue_cfg_req(struct mpt_softc */*mpt*/, request_t */*req*/,
1089                                   cfgparms_t *params,
1090                                   bus_addr_t /*addr*/, bus_size_t/*len*/,
1091                                   int /*sleep_ok*/, int /*timeout_ms*/);
1092 int             mpt_read_extcfg_header(struct mpt_softc *mpt, int PageVersion,
1093                                        int PageNumber, uint32_t PageAddress,
1094                                        int ExtPageType,
1095                                        CONFIG_EXTENDED_PAGE_HEADER *rslt,
1096                                        int sleep_ok, int timeout_ms);
1097 int             mpt_read_extcfg_page(struct mpt_softc *mpt, int Action,
1098                                      uint32_t PageAddress,
1099                                      CONFIG_EXTENDED_PAGE_HEADER *hdr,
1100                                      void *buf, size_t len, int sleep_ok,
1101                                      int timeout_ms);
1102 int             mpt_read_cfg_header(struct mpt_softc *, int /*PageType*/,
1103                                     int /*PageNumber*/,
1104                                     uint32_t /*PageAddress*/,
1105                                     CONFIG_PAGE_HEADER *,
1106                                     int /*sleep_ok*/, int /*timeout_ms*/);
1107 int             mpt_read_cfg_page(struct mpt_softc *t, int /*Action*/,
1108                                   uint32_t /*PageAddress*/,
1109                                   CONFIG_PAGE_HEADER *, size_t /*len*/,
1110                                   int /*sleep_ok*/, int /*timeout_ms*/);
1111 int             mpt_write_cfg_page(struct mpt_softc *, int /*Action*/,
1112                                    uint32_t /*PageAddress*/,
1113                                    CONFIG_PAGE_HEADER *, size_t /*len*/,
1114                                    int /*sleep_ok*/, int /*timeout_ms*/);
1115 static __inline int
1116 mpt_read_cur_cfg_page(struct mpt_softc *mpt, uint32_t PageAddress,
1117                       CONFIG_PAGE_HEADER *hdr, size_t len,
1118                       int sleep_ok, int timeout_ms)
1119 {
1120         return (mpt_read_cfg_page(mpt, MPI_CONFIG_ACTION_PAGE_READ_CURRENT,
1121                                   PageAddress, hdr, len, sleep_ok, timeout_ms));
1122 }
1123
1124 static __inline int
1125 mpt_write_cur_cfg_page(struct mpt_softc *mpt, uint32_t PageAddress,
1126                        CONFIG_PAGE_HEADER *hdr, size_t len, int sleep_ok,
1127                        int timeout_ms)
1128 {
1129         return (mpt_write_cfg_page(mpt, MPI_CONFIG_ACTION_PAGE_WRITE_CURRENT,
1130                                    PageAddress, hdr, len, sleep_ok,
1131                                    timeout_ms));
1132 }
1133
1134 /* mpt_debug.c functions */
1135 void mpt_print_reply(void *vmsg);
1136 void mpt_print_db(uint32_t mb);
1137 void mpt_print_config_reply(void *vmsg);
1138 char *mpt_ioc_diag(uint32_t diag);
1139 void mpt_req_state(mpt_req_state_t state);
1140 void mpt_print_config_request(void *vmsg);
1141 void mpt_print_request(void *vmsg);
1142 void mpt_dump_sgl(SGE_IO_UNION *se, int offset);
1143
1144 #endif /* _MPT_H_ */