yongari [Mon, 26 Nov 2012 02:42:19 +0000 (02:42 +0000)]
MFC r241388-241393:
r241388:
If the maximum payload size is 256 bytes or more, set the DMA write
water mark to 256 bytes. Otherwise controller will encounter DMA
write under run errors and would result in RX DMA hang. If the
maximum payload size is 128 bytes, the water mark is set to 128
bytes as usual.
While here, set maximum read request size to 2048 for BCM5719/BCM5720.
For other PCIe devices, use 4096. And reprogram the maximum read
request size whenever device reset is performed.
r241389:
On PHY write error use hex number to show the value.
Add more comments.
r241390:
Honor PHY type fiber for BCM5717/BCM5718/BCM5719/BCM5720.
r241391:
Do not force PCIe 1.0a mode in device reset on BCM5717 and newer
controllers. BCM5785 does not require PCI 1.0a mode as well during
reset.
r241392:
Fix a long standing VCPU reset sequence bug on BCM5906.
The VCPU(Virtual CPU) of BCM5906 is used to provide a mechanism to
control the bootcode execution and to pick up configuration data
stored inside the EEPROM.
The bootcode of BCM5906 will check the BGE_VCPU_STATUS_DRV_RESET
bit to decide which booting procedure to choose.
Data sheet indicates the VCPU of BCM5906 should set
BGE_VCPU_STATUS_DRV_RESET bit *before* VCPU reset or global reset.
r241393:
Remove unnecessary delay. I don't see any comments in data sheet
that requires 10ms delay after device reset. Because that code was
there from day 1, I guess it was added to give enough settlement
time after updating BGE_MAC_MODE register.
The recommended delay time for BGE_MAC_MODE after updating is 40us
and it was already done in r241219.
remko [Fri, 23 Nov 2012 21:27:26 +0000 (21:27 +0000)]
MFC r232486
Add an ifconfig carp option that enables users to set
the state of the carp cluster.
This is a direct commit to stable/9 because -HEAD's
code is very different. I discussed this with Gleb
and the reason for this is that since we do not
touch the kernel itself and are not adding very
weird or confusing things, we can commit this to the
stable branch directly.
The options 'master' and 'backup' are now available,
which enables the administrator to force a node into
the backup or master state on the cluster. Ofcourse
preempt has to be disabled otherwise the master node
will become master again.
One can do that with:
sysctl net.inet.carp.preempt=0
After that one can schedule maintenance on the node
normally running as the master and such.
nyan [Fri, 23 Nov 2012 15:44:04 +0000 (15:44 +0000)]
MFC: r225977, r242867, r242868, r242869
MFi386: r225936
Add some improvements in the idle table callbacks:
- Replace instances of manual assembly instruction "hlt" call
with halt() function calling.
- In cpu_idle_mwait() avoid races in check to sched_runnable() using
the same pattern used in cpu_idle_hlt() with the 'hlt' instruction.
- Add comments explaining the logic behind the pattern used in
cpu_idle_hlt() and other idle callbacks.
MFi386: r211924
Register an interrupt vector for DTrace return probes.
Fix some KASSERTs.
They are missing changes from r208833, r227394 and r227442.
trociny [Mon, 19 Nov 2012 21:11:58 +0000 (21:11 +0000)]
MFC r240997:
Kernel and modules have "set_vnet" linker set, where virtualized
global variables are placed. When a module is loaded by link_elf
linker its variables from "set_vnet" linker set are copied to the
kernel "set_vnet" ("modspace") and all references to these variables
inside the module are relocated accordingly.
The issue is when a module is loaded that has references to global
variables from another, previously loaded module: these references are
not relocated so an invalid address is used when the module tries to
access the variable. The example is V_layer3_chain, defined in ipfw
module and accessed from ipfw_nat.
The same issue is with DPCPU variables, which use "set_pcpu" linker
set.
Fix this making the link_elf linker on a module load recognize
"external" DPCPU/VNET variables defined in the previously loaded
modules and relocate them accordingly. For this set_pcpu_list and
set_vnet_list are used, where the addresses of modules' "set_pcpu" and
"set_vnet" linker sets are stored.
Note, archs that use link_elf_obj (amd64) were not affected by this
issue.
dim [Sat, 17 Nov 2012 23:39:36 +0000 (23:39 +0000)]
MFC r243037:
Fix a bug in aicasm_gram.y, noted by a newer clang 3.2 snapshot: it
compared an enum scope_type against a yacc-generated define, so the
condition would always be false.
mav [Fri, 16 Nov 2012 03:08:23 +0000 (03:08 +0000)]
MFC r242422:
Only four specific ATA PIO commands transfer several sectors per DRQ block
(interrupt). All other ATA PIO commands transfer one sector or 512 bytes
at one time. Hardcode these exceptions in ata(4) with ATA_CAM option.
This fixes timeout of READ LOG EXT command used by `smartctl -x /dev/adaX`.
mav [Fri, 16 Nov 2012 03:05:27 +0000 (03:05 +0000)]
MFC r242156:
Implement CAM_ATAIO_NEEDRESULT (fetching full set of result registers) for
ata(4) driver in ATA_CAM mode. That slighty improves error reporting and
also should fix `smartctl -l scterc /dev/adaX` operation.
mav [Fri, 16 Nov 2012 03:02:07 +0000 (03:02 +0000)]
MFC r241144, r241160:
Implement SATA revision (speed) control for legacy SATA controller for
both boot (via loader tunables) and run-time (via `camcontrol negotiate`).
Tested to work at least on NVIDIA MCP55 chipset.
mav [Fri, 16 Nov 2012 02:55:03 +0000 (02:55 +0000)]
MFC r232380:
Fix names of some Marvell SATA chips. It looks like chips with proprietary
interface supported by mvs(4) are 88SX, while AHCI-like chips are 88SE.
mav [Thu, 15 Nov 2012 06:04:39 +0000 (06:04 +0000)]
MFC r242417:
ASUS EeePC 1001px has strange variant of ALC269 CODEC, that mutes speaker
if unused in that configuration mixer at NID 15 is muted. Probably CODEC
incorrectly reports its internal connections. Hide that muter from the
driver to avoid muting and make built-in speaker work.
There are several different CODECs sharing this ID and I have not enough
information about them and the bug to implement more universal solution.
mav [Thu, 15 Nov 2012 05:58:37 +0000 (05:58 +0000)]
MFC r242357:
Set all pins initial connection status to unknown (2) and then update it
with the real value in regular way if sensing is supported. This fixes
minor inconsistency when playback redirection appeared in undefined state
on boot if headphones were not connected.
mav [Thu, 15 Nov 2012 05:46:02 +0000 (05:46 +0000)]
MFC r240762:
Restore handling of the third argument (id) of hid_start_parse(), same as
it is done in NetBSD/OpenBSD, and as it was here before r205728.
I personally think this API or its implementation is incorrect, as it is not
correct to filter collections based on report ID, as they are orthogonal
in general case, but I see no harm from supporting this feature.
mav [Thu, 15 Nov 2012 05:34:14 +0000 (05:34 +0000)]
MFC r242314:
Make GEOM RAID more aggressive in marking volumes as clean on shutdown
and move that action from shutdown_pre_sync to shutdown_post_sync stage
to avoid extra flapping.
ZFS tends to not close devices on shutdown, that doesn't allow GEOM RAID
to shutdown gracefully. To handle that, mark volume as clean just when
shutdown time comes and there are no active writes.
hselasky [Tue, 13 Nov 2012 17:11:36 +0000 (17:11 +0000)]
MFC r240750, r241987 and r242126:
Add missing CTLFLAG_TUN flag to tunable sysctls in the USB stack.
Adjust timing parameters of FULL/LOW/HIGH speed USB enumeration
and make these timing parameters tunable. This patch will fix
enumeration with some USB devices.
Fix a typo.
dim [Mon, 12 Nov 2012 07:47:19 +0000 (07:47 +0000)]
MFC r242625:
Remove duplicate const specifiers in many drivers (I hope I got all of
them, please let me know if not). Most of these are of the form:
static const struct bzzt_type {
[...list of members...]
} const bzzt_devs[] = {
[...list of initializers...]
};
The second const is unnecessary, as arrays cannot be modified anyway,
and if the elements are const, the whole thing is const automatically
(e.g. it is placed in .rodata).
I have verified this does not change the binary output of a full kernel
build (except for build timestamps embedded in the object files).
eadler [Fri, 9 Nov 2012 00:35:54 +0000 (00:35 +0000)]
MFC r242462:
10 years too late add support for "2.88MB 3.5in Extra High Density"
floppies.
Its unlikely that anyone actually uses these or cares about these
anymore, since we support other floppy types and this change doesn't
hurt - just add it.
yongari [Thu, 8 Nov 2012 02:08:42 +0000 (02:08 +0000)]
MFC r242425:
Remove TCP/UDP checksum offloading feature for IP fragmented
datagrams. Traditionally upper stack fragmented packets without
computing TCP/UDP checksum and these datagrams were passed to
driver. But there are chances that other packets slip into the
interface queue in SMP world. If this happens firmware running on
MIPS 4000 processor in the controller would see mixed packets and
it shall send out corrupted packets.
While I'm here simplify checksum offloading setup.
mav [Tue, 6 Nov 2012 02:08:09 +0000 (02:08 +0000)]
MFC r241329:
Make graid command line a bit more friendly by allowing volume name or
provider name to be specified instead of geom name (first argument in all
subcommands except label). In most cases there is only one array used
any way, so it is not really useful to make user type ugly geom names like
Intel-f0bdf223 or SiI-732c2b9448cf. Though they can be used in some cases.
yongari [Tue, 6 Nov 2012 01:04:46 +0000 (01:04 +0000)]
MFC r242348:
TSO engine of L1 requires a separate DMA descriptor for TCP
payload. This means driver has to split a TX buffer into two
pieces of TX buffers when the TX buffer contains both
ethernet/IP/TCP header and partial TCP payload. The controller
does not require all header should be in a TX buffer but driver
forced it to compute IP/TCP header size/offset which is required
parameter to configure DMA descriptor for TSO.
While here, slightly reorder DMA descriptor setup to enhance
readability and remove unnecessary code for TSO(upper stack never
requests TSO when the frame length is less than or equal to MTU).
eadler [Tue, 6 Nov 2012 00:55:43 +0000 (00:55 +0000)]
MFC r242514,r242541:
Revert the change that makes less default.
Since I've committed this I've receieved roughly an equal
amount of email thanking me for making this change
and asking me to revert it.
I've resisted making this change because
new users tend to prefer less over more
and these users are the least likely to know
how to change the PAGER on their own.
Requested by: many
Objected to: just as many
Decision made by: core
====
Change default prompt to show ~ again for the home directory
des [Mon, 5 Nov 2012 10:45:37 +0000 (10:45 +0000)]
MFH r225813, r233648: man page fixes
MFH r234837: avoid busy-loop on slow connections
MFH r234838: don't reuse credentials when redirected to another host
MFH r240496: use libmd if and only if OpenSSL is not available
jamie [Fri, 2 Nov 2012 01:32:22 +0000 (01:32 +0000)]
MFC r225191:
Delay the recursive decrement of pr_uref when jails are made invisible
but not removed; decrement it instead when the child jail actually
goes away. This avoids letting the counter go below zero in the case
where dying (pr_uref==0) jails are "resurrected", and an associated
KASSERT panic.
np [Tue, 30 Oct 2012 19:24:05 +0000 (19:24 +0000)]
MFC r242087:
Initialize the response queue mutex a bit earlier to avoid a panic that
occurs if t3_sge_alloc_qset fails and then t3_free_qset attempts to
destroy an uninitialized mutex.
projects / FreeBSD / stable / 8.git / log