arybchik [Wed, 25 Mar 2015 13:45:20 +0000 (13:45 +0000)]
MFC: 280163
sfxge: prefetch txq->common if TxQ is started only
Transmit may be called when TxQ is not started yet (i.e. txq->common is
invalid). TxQ state is checked below when mbuf is processed and dropped
if TxQ is not started.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
arybchik [Wed, 25 Mar 2015 13:18:51 +0000 (13:18 +0000)]
MFC: 279351
sfxge: expect required init_state on data path and in periodic calls
With the patch applied the number of instruction events is 1% less and
number of mispredicted branch events is 5% less under multistream TCP
traffic load close to line rate.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
hselasky [Wed, 25 Mar 2015 13:14:25 +0000 (13:14 +0000)]
MFC r280322 and r280429:
The synchronisation value returned by the so-called feedback endpoint
appears to be too inaccurate that it can be used to synchronize the
playback data stream. If there is a recording endpoint associated with
the playback endpoint, use that instead. That means if the isochronous
OUT endpoint is asynchronus the USB audio driver will automatically
start recording, if possible, to get exact information about the
needed sample rate adjustments. In no recording endpoint is present,
no rate adaption will be done.
While at it fix an issue where the hardware buffer pointers don't get
reset at the first device PCM trigger.
Make some variables 32-bit to avoid problems with multithreading.
Use the feedback value from the synchronization endpoint as fallback
when there is no recording channel.
arybchik [Wed, 25 Mar 2015 13:12:15 +0000 (13:12 +0000)]
MFC: 279183
sfxge: add common code support for changing TX queue pace
To delay packets from a particular TX queue by a particular time, write a value
into the TX Pace table s.t. pace time <= TX Pace Clock Period * (2 ^ pace value)
- the TX pace clock is 1/13 of the system clock, so its period should be 104 or
52 ns depending on whether turbo mode is active.
EFX_TX_PACE_CLOCK_BASE added by me.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
arybchik [Wed, 25 Mar 2015 13:05:33 +0000 (13:05 +0000)]
MFC: 279178
sfxge: do no allow EFSYS_MEM_ALLOC sleep
It solves locking problem when EFSYS_MEM_ALLOC is called in
the context holding a mutex (not allowed to sleep).
E.g. on interface bring up or multicast addresses addition.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
arybchik [Wed, 25 Mar 2015 13:03:36 +0000 (13:03 +0000)]
MFC: 279176
sfxge: pass correct address to free allocated memory in the case of load error
It is one more place missed in the previous fix.
Most likely is was just memory leak on the error handling path since
typically efsys_mem_t is filled in by zeros on allocation.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
hselasky [Wed, 25 Mar 2015 13:01:51 +0000 (13:01 +0000)]
MFC r280345:
Fix for out of order device destruction notifications when using the
delist_dev() function. In addition to this change:
- add a proper description of this function
- add a proper witness assert inside this function
- switch a nearby line to use the "cdp" pointer instead of cdev2priv()
arybchik [Wed, 25 Mar 2015 11:06:16 +0000 (11:06 +0000)]
MFC: 279141
sfxge: style fixes and cleanup
Sync endif comment with conditional.
BOOTROM and SIENA_BOOTROM are the same, but highlight that it is Siena.
Restore commented out assertion.
Sync comments with out-of-tree driver.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
arybchik [Wed, 25 Mar 2015 11:04:12 +0000 (11:04 +0000)]
MFC: 279098
sfxge: allow TX and RX queue limits to be changed
Before the common code had hard coded limits on the IDs RXQs and TXQs could
be created with which were suited for the Windows driver with VMQ, and so
would prevent queues with IDs greater than or equal to 259 (for TXQs) or 768
(for RXQs) from being created. This change allows the limits to be set in
efsys.h, so that all 1024 queues can be created during new manftest tests.
Also, the descriptor cache sizes were also hard coded to values suited to
the smaller queue counts, and so it was necessary to make them configurable
as well.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
arybchik [Wed, 25 Mar 2015 11:00:09 +0000 (11:00 +0000)]
MFC: 279095
sfxge: never set RX_DESCQ_EN during self-test
We must not enable RX queues with random parameters when they are
mapped into a VF with an untrusted driver. It's probably not a good
idea to do this anyway, so take this bit out of the table test masks.
Submitted by: Ben Hutchings
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
arybchik [Wed, 25 Mar 2015 10:57:26 +0000 (10:57 +0000)]
MFC: 279078
sfxge: add assertions that required event handlers are implemented
efx_ev_mcdi() does not assert or check that all event handlers it
calls are non-null. Add assertions at the top for all required
event handlers, as some events (in the case of this bug, monitor
events) are rare.
Submitted by: Ben Hutchings
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
hselasky [Wed, 25 Mar 2015 10:55:08 +0000 (10:55 +0000)]
MFC r279281:
Fix a special case in ip_fragment() to produce a more sensible chain
of packets. When the data payload length excluding any headers, of an
outgoing IPv4 packet exceeds PAGE_SIZE bytes, a special case in
ip_fragment() can kick in to optimise the outgoing payload(s). The
code which was added in r98849 as part of zero copy socket support
assumes that the beginning of any MTU sized payload is aligned to
where a MBUF's "m_data" pointer points. This is not always the case
and can sometimes cause large IPv4 packets, as part of ping replies,
to be split more than needed.
Instead of iterating the MBUFs to figure out how much data is in the
current chain, use the value already in the "m_pkthdr.len" field of
the first MBUF in the chain.
arybchik [Wed, 25 Mar 2015 10:48:28 +0000 (10:48 +0000)]
MFC: 278941
sfxge: support variable-length response to MCDI GET_BOARD_CFG
Allocate the minimum or maximum response length for GET_BOARD_CFG as
appropriate. When looking up firmware subtypes by partition ID,
check the ID against the actual response length.
Merge of the patch made by Ben Hutchings in 2011.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
arybchik [Wed, 25 Mar 2015 10:35:19 +0000 (10:35 +0000)]
MFC: 278835
sfxge: remove full_packet_size from sfxge_tso_state
It makes sfxge_tso_state smaller and even makes tso_start_new_packet()
few bytes smaller. Data used to calculate packet size are used nearby,
so it should be no problems with cache etc.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor), glebius
arybchik [Wed, 25 Mar 2015 10:25:45 +0000 (10:25 +0000)]
MFC: 277895
sfxge: Separate software Tx queue limit for non-TCP traffic
Add separate software Tx queue limit for non-TCP traffic to make total
limit higher and avoid local drops of TCP packets because of no
backpressure.
There is no point to make non-TCP limit high since without backpressure
UDP stream easily overflows any sensible limit.
Split early drops statistics since it is better to have separate counter
for each drop reason to make it unabmiguous.
Add software Tx queue high watermark. The information is very useful to
understand how big queues grow under traffic load.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
arybchik [Wed, 25 Mar 2015 10:14:30 +0000 (10:14 +0000)]
MFC: 277887
sfxge: Remove extra cache-line alignment and reorder sfxge_evq_t
Remove the first member alignment to cacheline since it is nop.
Use __aligned() for the whole structure to make sure that the structure
size is cacheline aligned.
Remove lock alignment to make the structure smaller and fit all members
used on event queue processing into one cacheline (128 bytes) on x86-64.
The lock is obtained as well from different context when event queue
statistics are retrived from sysctl context, but it is infrequent.
Reorder members to avoid padding and go in usage order on event
processing.
As the result all structure members used on event queue processing fit
into exactly one cacheline (128 byte) now.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
arybchik [Wed, 25 Mar 2015 10:12:13 +0000 (10:12 +0000)]
MFC: 277885
sfxge: Move txq->next pointer to part writable on completion path
In fact the pointer is used only if more than one TXQ is processed in
one interrupt.
It is used (read-write) on completion path only.
Also it makes the first part of the structure smaller and it fits now
into one 128byte cache line. So, TXQ structure becomes 128 bytes
smaller.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
arybchik [Wed, 25 Mar 2015 10:05:19 +0000 (10:05 +0000)]
MFC: 272331
Support tunable to control Tx deferred packet list limits
Also increase default for Tx queue get-list limit.
Too small limit results in TCP packets drops especiall when many
streams are running simultaneously.
Put list may be kept small enough since it is just a temporary
location if transmit function can't get Tx queue lock.
Submitted by: Andrew Rybchenko <arybchenko at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
arybchik [Wed, 25 Mar 2015 09:59:38 +0000 (09:59 +0000)]
MFC: 272325
cleanup: code style fixes
Remove trailing whitespaces and tabs.
Enclose value in return statements in parentheses.
Use tabs after #define.
Do not skip comparison with 0/NULL in boolean expressions.
Submitted by: Andrew Rybchenko <arybchenko at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
arybchik [Wed, 25 Mar 2015 09:56:48 +0000 (09:56 +0000)]
MFC: 263649
sfxge: limit software Tx queue size.
Previous implementation limits put queue size only (when Tx lock can't
be acquired), but get queue may grow unboundedly which results in mbuf
pools exhaustion and latency growth.
Submitted by: Andrew Rybchenko <Andrew.Rybchenko at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
ken [Tue, 24 Mar 2015 16:53:16 +0000 (16:53 +0000)]
MFC, r279375
------------------------------------------------------------------------
r279375 | ken | 2015-02-27 14:35:36 -0700 (Fri, 27 Feb 2015) | 26 lines
Fix I/O size calculation for pass(4) driver requests and add latency
tracking.
It is important to subtract the residual from the requested
transfer size to see how much data was actually transferred. With
tape drives in particular, it is common to request more data than is
returned.
Also, add I/O latency tracking for CAM requests issued by
cam_periph_runccb().
If the caller supplies a struct devstat, and the I/O is a SCSI or
ATA I/O, we will track the elapsed time to provide I/O latency
statistics for the request.
sys/cam/scsi/cam_periph.c:
In cam_periph_runccb(), subtract the residual when reporting I/O
totals to devstat(9) for SCSI and ATA passthrough requests.
In cam_periph_runccb(), grab the I/O start time and supply
the start time to devstat_end_transaction() so that it can
calculate the elapsed I/O time.
ken [Tue, 24 Mar 2015 14:36:10 +0000 (14:36 +0000)]
MFC sa(4) and mt(1) improvements.
This includes these changes: 279219, 279229, 279261, 279534, 279570,
280230, 280231.
In addition, bump __FreeBSD_version for the addition of the new
mtio(4) / sa(4) ioctls.
Thanks to Dan Langille, Harald Schmalzbauer and Rudolf Cejka for spending
a significant amount of time and effort testing these changes.
------------------------------------------------------------------------
r279219 | ken | 2015-02-23 14:59:30 -0700 (Mon, 23 Feb 2015) | 282 lines
Significant upgrades to sa(4) and mt(1).
The primary focus of these changes is to modernize FreeBSD's
tape infrastructure so that we can take advantage of some of the
features of modern tape drives and allow support for LTFS.
Significant changes and new features include:
o sa(4) driver status and parameter information is now exported via an
XML structure. This will allow for changes and improvements later
on that will not break userland applications. The old MTIOCGET
status ioctl remains, so applications using the existing interface
will not break.
o 'mt status' now reports drive-reported tape position information
as well as the previously available calculated tape position
information. These numbers will be different at times, because
the drive-reported block numbers are relative to BOP (Beginning
of Partition), but the block numbers calculated previously via
sa(4) (and still provided) are relative to the last filemark.
Both numbers are now provided. 'mt status' now also shows the
drive INQUIRY information, serial number and any position flags
(BOP, EOT, etc.) provided with the tape position information.
'mt status -v' adds information on the maximum possible I/O size,
and the underlying values used to calculate it.
o The extra sa(4) /dev entries (/dev/saN.[0-3]) have been removed.
The extra devices were originally added as place holders for
density-specific device nodes. Some OSes (NetBSD, NetApp's OnTap
and Solaris) have had device nodes that, when you write to them,
will automatically select a given density for particular tape drives.
This is a convenient way of switching densities, but it was never
implemented in FreeBSD. Only the device nodes were there, and that
sometimes confused users.
For modern tape devices, the density is generally not selectable
(e.g. with LTO) or defaults to the highest availble density when
the tape is rewritten from BOT (e.g. TS11X0). So, for most users,
density selection won't be necessary. If they do need to select
the density, it is easy enough to use 'mt density' to change it.
o Protection information is now supported. This is either a
Reed-Solomon CRC or CRC32 that is included at the end of each block
read and written. On write, the tape drive verifies the CRC, and
on read, the tape drive provides a CRC for the userland application
to verify.
o New, extensible tape driver parameter get/set interface.
o Density reporting information. For drives that support it,
'mt getdensity' will show detailed information on what formats the
tape drive supports, and what formats the tape drive supports.
o Some mt(1) functionality moved into a new mt(3) library so that
external applications can reuse the code.
o The new mt(3) library includes helper routines to aid in parsing
the XML output of the sa(4) driver, and build a tree of driver
metadata.
o Support for the MTLOAD (load a tape in the drive) and MTWEOFI
(write filemark immediate) ioctls needed by IBM's LTFS
implementation.
o Improve device departure behavior for the sa(4) driver. The previous
implementation led to hangs when the device was open.
o This has been tested on the following types of drives:
IBM TS1150
IBM TS1140
IBM LTO-6
IBM LTO-5
HP LTO-2
Seagate DDS-4
Quantum DLT-4000
Exabyte 8505
Sony DDS-2
lib/libmt/Makefile,
lib/libmt/mt.3,
lib/libmt/mtlib.c,
lib/libmt/mtlib.h,
New mt(3) library that contains functions moved from mt(1) and
new functions needed to interact with the updated sa(4) driver.
This includes XML parser helper functions that application writers
can use when writing code to query tape parameters.
rescue/rescue/Makefile:
Add -lmt to CRUNCH_LIBS.
src/share/man/man4/mtio.4
Clarify this man page a bit, and since it contains what is
essentially the mtio.h header file, add new ioctls and structure
definitions from mtio.h.
src/share/man/man4/sa.4
Update BUGS and maintainer section.
sys/cam/scsi/scsi_all.c,
sys/cam/scsi/scsi_all.h:
Add SCSI SECURITY PROTOCOL IN/OUT CDB definitions and CDB building
functions.
sys/cam/scsi/scsi_sa.c
sys/cam/scsi/scsi_sa.h
Many tape driver changes, largely outlined above.
Increase the sa(4) driver read/write timeout from 4 to 32
minutes. This is based on the recommended values for IBM LTO
5/6 drives. This may also avoid timeouts for other tape
hardware that can take a long time to do retries and error
recovery. Longer term, a better way to handle this is to ask
the drive for recommended timeout values using the REPORT
SUPPORTED OPCODES command. Modern IBM and Oracle tape drives
at least support that command, and it would allow for more
accurate timeout values.
Add XML status generation. This is done with a series of
macros to eliminate as much duplicate code as possible. The
new XML-based status values are reported through the new
MTIOCEXTGET ioctl.
Add XML driver parameter reporting, using the new MTIOCPARAMGET
ioctl.
Add a new driver parameter setting interface, using the new
MTIOCPARAMSET and MTIOCSETLIST ioctls.
Add a new MTIOCRBLIM ioctl to get block limits information.
Add CCB/CDB building routines scsi_locate_16, scsi_locate_10,
and scsi_read_position_10().
scsi_locate_10 implements the LOCATE command, as does the
existing scsi_set_position() command. It just supports
additional arguments and features. If/when we figure out a
good way to provide backward compatibility for older
applications using the old function API, we can just revamp
scsi_set_position(). The same goes for
scsi_read_position_10() and the existing scsi_read_position()
function.
Revamp sasetpos() to take the new mtlocate structure as an
argument. It now will use either scsi_locate_10() or
scsi_locate_16(), depending upon the arguments the user
supplies. As before, once we change position we don't have a
clear idea of what the current logical position of the tape
drive is.
For tape drives that support long form position data, we
read the current position and store that for later reporting
after changing the position. This should help applications
like Bacula speed tape access under FreeBSD once they are
modified to support the new ioctls.
Add a new quirk, SA_QUIRK_NO_LONG_POS, that is set for all
drives that report SCSI-2 or older, as well as drives that
report an Illegal Request type error for READ POSITION with
the long format. So we should automatically detect drives
that don't support the long form and stop asking for it after
an initial try.
Add a partition number to the sa(4) softc.
Improve device departure handling. The previous implementation
led to hangs when the device was open.
If an application had the sa(4) driver open, and attempted to
close it after it went away, the cam_periph_release() call in
saclose() would cause the periph to get destroyed because that
was the last reference to it. Because destroy_dev() was
called from the sa(4) driver's cleanup routine (sacleanup()),
and would block waiting for the close to happen, a deadlock
would result.
So instead of calling destroy_dev() from the cleanup routine,
call destroy_dev_sched_cb() from saoninvalidate() and wait for
the callback.
Acquire a reference for devfs in saregister(), and release it
in the new sadevgonecb() routine when all devfs devices for
the particular sa(4) driver instance are gone.
Add a new function, sasetupdev(), to centralize setting
per-instance devfs device parameters instead of repeating the
code in saregister().
Add an open count to the softc, so we know how many
peripheral driver references are a result of open
sessions.
Add the D_TRACKCLOSE flag to the cdevsw flags so
that we get a 1:1 mapping of open to close calls
instead of a N:1 mapping.
This should be a no-op for everything except the
control device, since we don't allow more than one
open on non-control devices.
However, since we do allow multiple opens on the
control device, the combination of the open count
and the D_TRACKCLOSE flag should result in an
accurate peripheral driver reference count, and an
accurate open count.
The accurate open count allows us to release all
peripheral driver references that are the result
of open contexts once we get the callback from devfs.
sys/sys/mtio.h:
Add a number of new mt(4) ioctls and the requisite data
structures. None of the existing interfaces been removed
or changed.
This includes definitions for the following new ioctls:
MTIOCRBLIM /* get block limits */
MTIOCEXTLOCATE /* seek to position */
MTIOCEXTGET /* get tape status */
MTIOCPARAMGET /* get tape params */
MTIOCPARAMSET /* set tape params */
MTIOCSETLIST /* set N params */
usr.bin/mt/Makefile:
mt(1) now depends on libmt, libsbuf and libbsdxml.
usr.bin/mt/mt.1:
Document new mt(1) features and subcommands.
usr.bin/mt/mt.c:
Implement support for mt(1) subcommands that need to
use getopt(3) for their arguments.
Implement a new 'mt status' command to replace the old
'mt status' command. The old status command has been
renamed 'ostatus'.
The new status function uses the MTIOCEXTGET ioctl, and
therefore parses the XML data to determine drive status.
The -x argument to 'mt status' allows the user to dump out
the raw XML reported by the kernel.
The new status display is mostly the same as the old status
display, except that it doesn't print the redundant density
mode information, and it does print the current partition
number and position flags.
Add a new command, 'mt locate', that will supersede the
old 'mt setspos' and 'mt sethpos' commands. 'mt locate'
implements all of the functionality of the MTIOCEXTLOCATE
ioctl, and allows the user to change the logical position
of the tape drive in a number of ways. (Partition,
block number, file number, set mark number, end of data.)
The immediate bit and the explicit address bits are
implemented, but not documented in the man page.
Add a new 'mt weofi' command to use the new MTWEOFI ioctl.
This allows the user to ask the drive to write a filemark
without waiting around for the operation to complete.
Add a new 'mt getdensity' command that gets the XML-based
tape drive density report from the sa(4) driver and displays
it. This uses the SCSI REPORT DENSITY SUPPORT command
to get comprehensive information from the tape drive about
what formats it is able to read and write.
Add a new 'mt protect' command that allows getting and setting
tape drive protection information. The protection information
is a CRC tacked on to the end of every read/write from and to
the tape drive.
Sponsored by: Spectra Logic
MFC after: 1 month
------------------------------------------------------------------------
------------------------------------------------------------------------
r279229 | ken | 2015-02-23 22:43:16 -0700 (Mon, 23 Feb 2015) | 5 lines
Fix printf format warnings on sparc64 and mips.
Sponsored by: Spectra Logic
MFC after: 1 month
------------------------------------------------------------------------
------------------------------------------------------------------------
r279261 | ken | 2015-02-24 21:30:23 -0700 (Tue, 24 Feb 2015) | 23 lines
Fix several problems found by Coverity.
lib/libmt/mtlib.c:
In mt_start_element(), make sure we don't overflow the
cur_sb array. CID 1271325
usr.bin/mt/mt.c:
In main(), bzero the mt_com structure so that we aren't
using any uninitialized stack variables. CID 1271319
In mt_param(), only allow one -s and one -p argument. This
will prevent a memory leak caused by overwriting the
param_name and/or param_value variables. CID 1271320 and
CID 1271322
To make things simpler in mt_param(), make sure there
there is only one exit path for the function. Make sure
the arguments are explicitly freed.
------------------------------------------------------------------------
------------------------------------------------------------------------
r279534 | ken | 2015-03-02 11:09:49 -0700 (Mon, 02 Mar 2015) | 18 lines
Change the sa(4) driver to check for long position support on
SCSI-2 devices.
Some older tape devices claim to be SCSI-2, but actually do support
long position information. (Long position information includes
the current file mark.) For example, the COMPAQ SuperDLT1.
So we now only disable the check on SCSI-1 and older devices.
sys/cam/scsi/scsi_sa.c:
In saregister(), only disable fetching long position
information on SCSI-1 and older drives. Update the
comment to explain why.
------------------------------------------------------------------------
------------------------------------------------------------------------
r279570 | ken | 2015-03-03 15:49:07 -0700 (Tue, 03 Mar 2015) | 21 lines
Add density code for DAT-72, and notes on DAT-160.
As it turns out, the density code for DAT-160 (0x48) is the same
as for SDLT220. Since the SDLT values are already in the table,
we will leave them in place.
Thanks to Harald Schmalzbauer for confirming the DAT-72 density code.
lib/libmt/mtlib.c:
Add DAT-72 density code, and commented out DAT-160 density
code. Explain why DAT-160 is commented out. Add notes
explaining where the bpi values for these formats came from.
usr.bin/mt/mt.1:
Add DAT-72 density code, and add a note explaining that
the SDLTTapeI(110) density code (0x48) is the same as
DAT-160.
Sponsored by: Spectra Logic
MFC after: 3 weeks
------------------------------------------------------------------------
------------------------------------------------------------------------
r280230 | ken | 2015-03-18 14:52:34 -0600 (Wed, 18 Mar 2015) | 25 lines
Fix a couple of problems in the sa(4) media type reports.
The only drives I have discovered so far that support medium type
reports are newer HP LTO (LTO-5 and LTO-6) drives. IBM drives
only support the density reports.
sys/cam/scsi/scsi_sa.h:
The number of possible density codes in the medium type
report is 9, not 8. This caused problems parsing all of
the medium type report after this point in the structure.
usr.bin/mt/mt.c:
Run the density codes returned in the medium type report
through denstostring(), just like the primary and secondary
density codes in the density report. This will print the
density code in hex, and give a text description if it
is available.
Thanks to Rudolf Cejka for doing extensive testing with HP LTO drives
and Bacula and discovering these problems.
Tested by: Rudolf Cejka <cejkar at fit.vutbr.cz>
Sponsored by: Spectra Logic
MFC after: 4 days
------------------------------------------------------------------------
------------------------------------------------------------------------
r280231 | ken | 2015-03-18 14:54:54 -0600 (Wed, 18 Mar 2015) | 16 lines
Improve the mt(1) rblim display.
The granularity reported by READ BLOCK LIMITS is an exponent, not a
byte value. So a granularity of 0 means 2^0, or 1 byte. A
granularity of 1 means 2^1, or 2 bytes.
Print out the individual block limits on separate lines to improve
readability and avoid exceeding 80 columns.
usr.bin/mt/mt.c:
Fix and improve the 'mt rblim' output. Add a MT_PLURAL()
macro so we can print "byte" or "bytes" as appropriate.
kib [Tue, 24 Mar 2015 08:18:24 +0000 (08:18 +0000)]
MFC r280195:
When inserting new entry into the address map, ensure that not only
next entry does not intersect with the tail of the new entry, but also
that previous entry is also before new entry start.
Honor the following flags with the following rc.d scripts for services that can
be easily decoupled from the boot process without disrupting other services
ngie [Tue, 24 Mar 2015 06:59:41 +0000 (06:59 +0000)]
Forced commit to note that the previous commit to this file included the
following MFC as well:
MFC 278251:
Honor the following flags for items that can be conditionalized out of the
build/install without disrupting other dependent services (see r278249, et
al):