yongari [Thu, 24 Jan 2013 02:20:25 +0000 (02:20 +0000)]
MFC r244482:
Recognize 5720S PHY and treat it as 5708S PHY.
Unfortunately 5720S uses 5709S PHY id so add a hack to detect 5720S
PHY by checking parent device name. 5720S PHY does not support 2500SX.
gjb [Thu, 24 Jan 2013 01:41:11 +0000 (01:41 +0000)]
MFC r223148, r240252, r241541, r241543, r245756:
r223148: (ru)
- Document all trees that support CVS_UPDATE.
- Document all trees that support SUP_UPDATE.
- Document SVN_UPDATE.
- Document NO_WWWUPDATE.
- make.conf(5) mistakenly said that *SUPFILE* had defaults.
- Add an example entry for WWWSUPFILE.
r240252: (eadler)
- Remove documentation and www cvsup files as they are no longer
useful with the switch to subversion.
r241541: (joel)
- Minor mdoc improvements. Also remove unnecessary csup reference.
r241543: (eadler)
- Bump .Dd
r245756:
- Mark SUP_UPDATE as deprecated in make.conf(5), providing
instructions to use SVN_UPDATE or freebsd-update(8).
- While here, remove bogus NO_WWWUPDATE.
jhb [Wed, 23 Jan 2013 18:19:50 +0000 (18:19 +0000)]
MFC 229435:
Add special loader environment variables 'comconsole_port' and
'comconsole_pcidev'. The former allows to set the base address of the
serial console i/o port. The later takes the string of the format
'bus:device:function:[bar]' as a value and uses the serial port attached
as PCI device at the specified location for console.
Both variants pass 'hw.uart.console' variable to the uart driver to
properly hand-over the kernel console.
Change allows to use ISA serial ports other than COM1 for the
loader/kernel console without loader recompilation. Also, you can use
PCI-attached port as the console, e.g. Intel AMT serial pseudo-port on
some motherboards based on Q67 chipset.
mav [Tue, 22 Jan 2013 17:19:44 +0000 (17:19 +0000)]
MFC r244146:
Add IDs for SATA controllers on AMD Hudson-2 series chipsets.
I am not exactly sure about the naming due to lack of specs on AMD site,
but it is better to have some identification then none at all.
mav [Tue, 22 Jan 2013 17:18:34 +0000 (17:18 +0000)]
MFC r241402:
Add checks for ata_sata_scr_read() return statuses. It is mostly to silence
Clang Static Analyzer warnings as errors there are usually unlikely.
hselasky [Mon, 21 Jan 2013 07:41:27 +0000 (07:41 +0000)]
MFC r245132 and r245175:
Optimise the XHCI interrupt handling.
This patch will save CPU time when the XHCI interrupt is
shared with other devices.
Only check event rings when interrupt bits are set.
Otherwise would indicate hiding possible hardware fault(s).
hselasky [Mon, 21 Jan 2013 07:39:16 +0000 (07:39 +0000)]
MFC r243780:
- Add support for Etron EJ168 USB 3.0 Host Controllers.
This brand of controllers expects that the number of
contexts specified in the input slot context points
to an active endpoint context, else it refuses to
operate.
bapt [Tue, 15 Jan 2013 09:17:07 +0000 (09:17 +0000)]
MFC r244553,244594,244608,244639
In preparation for making 'pkg -N' the one true method of determining
whether a system has been configured to use pkgng, cause /usr/sbin/pkg
recognise a -N option and exit with a failure code when the pkg port
is not installed
bapt [Sun, 13 Jan 2013 22:36:12 +0000 (22:36 +0000)]
MFC: r243883
if PACKAGESITE url scheme is not 'file://', always try to revolv SRV records and
use them if any. It allows the bootstrap to use directly pkg.FreeBSD.org instead
of pkgbeta.FreeBSD.org
markj [Sun, 13 Jan 2013 04:14:30 +0000 (04:14 +0000)]
MFC r244995 r244996 r244997.
MFC r244995:
Fix a typo in an error message.
MFC r244996:
Have -n imply -r, since dry-run mode obviously doesn't require root
privileges.
MFC r244997:
Make sure to update the mtime of a logfile after archiving it. This
ensures that the next rotation happens at the correct time when using
interval-based rotations.
markj [Sun, 13 Jan 2013 04:13:14 +0000 (04:13 +0000)]
MFC r244719:
Add the NO_SYNC_CACHE quirk for all Apple USB MSC devices, as they
typically do not handle the SYNCHRONIZE_CACHE command - they either
return an error or the firmware enters a reset loop.
wblock [Thu, 10 Jan 2013 23:39:28 +0000 (23:39 +0000)]
MFC r245012:
Document the output of the show command. Modified version of patch
provided by Bas Smeelen <b.smeelen@ose.nl>. Use of 'gpart list'
suggested by by Andrey V. Elsukov <ae@FreeBSD.org>.
yongari [Tue, 8 Jan 2013 05:35:18 +0000 (05:35 +0000)]
MFC r244341:
Make sure to stop both TX and RX MACs in ale_stop_mac(). Previously
it used to stop TX MAC only such that MAC reconfiguration after
getting a link didn't work as expected.
rmacklem [Sun, 6 Jan 2013 01:17:58 +0000 (01:17 +0000)]
MFC: r244331
Fix the gssd daemon so that it uses syslog() to report
an error instead of calling err() when it is daemonized,
so that the error gets logged.
rmacklem [Sun, 6 Jan 2013 01:11:45 +0000 (01:11 +0000)]
MFC: r244226
The group list for a non-default export entry (a host/subnet one)
was being copied from the wrong place. This patch fixes that.
This could cause access failures for mapped users, when the group
permissions were needed.
markj [Sat, 5 Jan 2013 22:55:34 +0000 (22:55 +0000)]
- Add IFT_L2VLAN (vlan(4)) support.
- Add a -P option to support PID files. When -a is specified
/var/run/rarpd.pid is used by default, and when an interface is
specified /var/run/rarpd.<ifname>.pid is used by default.
pfg [Fri, 4 Jan 2013 04:03:39 +0000 (04:03 +0000)]
MFC r244941:
libedit: bind the correct command when using "bind -k".
"ed-argument-digit" (i. e. command 0) was incorrectly used
instead.
This bug comes from the original sources imported in 1994
and has been confirmed in upstream NetBSD.
Reported by: Yamagi Burmeister
Submitted by: Christoph Mallon
pfg [Fri, 4 Jan 2013 03:54:22 +0000 (03:54 +0000)]
MFC 244776, 244792:
gcc: avoid generating negative values to DW_AT_byte_size.
There is a bug in gcc (GCC/35998) where dwarf reports
sizes of unsigned -1 (0xffffffff).
On NetBSD this generated a faulty CTF entry which then
caused a segfault in ctfmerge. The issue was worked
around in NetBSD's Dtrace but since the issue originated
in gcc, it seems reasonable to fix it here.
Thanks to Christoph Mallon for pointing out a correct fix.
wblock [Thu, 3 Jan 2013 21:35:25 +0000 (21:35 +0000)]
MFC r242697,r242704:
r242697:
Add devd.conf(5) and devd(8) to SEE ALSO xrefs. Give users a pointer to
seemingly mysterious actions that are not done by ifconfig itself, but
by devd triggering on events caused by ifconfig.
r242704:
Remove fifteen-year-old notes on media selection (suggested by simon@).
Add commas after "e.g." and "i.e.".
delphij [Tue, 1 Jan 2013 07:04:25 +0000 (07:04 +0000)]
MFC r244369 (jimharris):
Use CAM_DEV_NOT_THERE instead of CAM_SEL_TIMEOUT to report nonexistent
LUNs for the virtual processor device. This removes lots of CAM warnings,
and follows similar recent changes to tws(4) and twa(4) drivers.
Also fix case where CAM_REQ_CMP was getting OR'd with CAM_DEV_NOT_THERE
in the nonexistent LUN case, resulting in different CAM status (CAM_UA_TERMIO)
getting reported to CAM. This issue existing previously, but was more subtle
because it changed CAM_SEL_TIMEOUT to CAM_CMD_TIMEOUT.
Sponsored by: Intel
Reported and tested by: Willem Jan Withagen <wjw@digiware.nl>
dim [Mon, 31 Dec 2012 14:21:41 +0000 (14:21 +0000)]
MFC r244600:
Fix a bug in ld --gc-sections: it strips out .note sections, while it
should never do so. This can cause global constructors and destructors
to not be executed at run-time, resulting in crashes and other strange
behaviour.
markj [Mon, 31 Dec 2012 03:35:01 +0000 (03:35 +0000)]
MFC 244523:
- Make sure that errno isn't modified before calling logerror() in error
conditions.
- Don't check for AF_INET6 when compiled without INET6 support.
gshapiro [Sat, 29 Dec 2012 19:12:38 +0000 (19:12 +0000)]
MFC: Properly define true/false when defining __bool_true_false_are_defined
for filters which pull in mfapi.h before stdbool.h. Issue reported by
Petr Rehor, maintainer of amavisd-milter port.
dim [Wed, 19 Dec 2012 12:19:56 +0000 (12:19 +0000)]
MFC r243907:
Fix an old bug in devd, where it uses std::sort() to sort the various
lists it reads from its configuration files on the priority field.
Because some items in the lists have the same priority, and std::sort()
is not stable, the exact order in which the items are enumerated does
not have to correspond to the order they appear in the configuration
files.
Apparently this was never noticed with libstdc++, but with libc++ it
could cause the "uhid" entry from /etc/devd/usb.conf to be used instead
of the "ums" entry (which is earlier in the file). This caused the
problem described in the PR: the USB mouse module was never loaded, and
the other actions (such as starting moused) were not executed.
To fix the problem, make devd use std:stable_sort() instead.
Reported by: Jan Beich <jbeich@tormail.org>
PR: bin/172958
delphij [Mon, 17 Dec 2012 06:38:22 +0000 (06:38 +0000)]
MFC r243834:
Note that the manual page of less(1) says:
Note that a preprocessor cannot output an empty file, since that
is interpreted as meaning there is no replacement, and the origi-
nal file is used. To avoid this, if LESSOPEN starts with two ver-
tical bars, the exit status of the script becomes meaningful. If
the exit status is zero, the output is considered to be replace-
ment text, even if it empty. If the exit status is nonzero, any
output is ignored and the original file is used. For compatibil-
ity with previous versions of less, if LESSOPEN starts with only
one vertical bar, the exit status of the preprocessor is ignored.
Use two pipe symbols for zless, so that zless'ing a compressed empty
file will give output rather than being interpreted as its compressed
form, which is typically a binary.
Thanks Mark Nudelman for pointing out this difference and the
suggested solution.
jimharris [Wed, 12 Dec 2012 00:39:32 +0000 (00:39 +0000)]
MFC r243904:
Don't call bus_dmamap_load in CAM_DIR_NONE case, since there is nothing
to map, and technically this isn't allowed.
Functionally, it works OK (at least on x86) to call bus_dmamap_load with
a NULL data pointer and zero length, so this is primarily for correctness
and consistency with other drivers.
While here, remove check in isci_io_request_construct for nseg==0.
Previously, bus_dmamap_load would pass nseg==1, even for case where
buffer is NULL and length = 0, which allowed CAM_DIR_NONE CCBs
to get processed. This check is not correct though, and needed to be
removed both for the changes elsewhere in this patch, as well as jeff's
preliminary bus_dmamap_load_ccb patch (which uncovered all of this in
the first place).
projects / FreeBSD / stable / 8.git / log