marius [Fri, 15 Jan 2010 19:06:33 +0000 (19:06 +0000)]
MFC: r201932
- Add code allowing a network device to only be open and closed once
by keeping it opened after the first open and closing it via the
cleanup handler when NETIF_OPEN_CLOSE_ONCE is defined in order to
avoid the open-close-dance on every file access which with firmware
that for example performs an auto-negotiation on every open causes
netbooting to take horribly long. Basically the behavior with this
knob enabled resembles the one employed between r60506 and r177108
(and for sparc64 also again since r182919) with the addition that
the network device now is closed eventually before entering the
kernel and before rebooting. Actually I think this should be the
desired MI behavior, however the U-Boot loader actually requires
net_close() to be called after every transaction in order for some
local shutdown operations to be performed (and which I think thus
will break on concurrent opens, i.e. when netdev_opens is > 1, like
the loader does at least for disks when LOADER_GZIP_SUPPORT is
enabled).
- Use NETIF_OPEN_CLOSE_ONCE to replace the hack, which artificially
increased netdev_opens for sparc64 in order to keep the network
device opened forever, as at least some firmware versions require
the network device to be closed eventually before entering the
kernel or otherwise will DMA received packets to stale memory.
The powerpc OFW loader probably wants NETIF_OPEN_CLOSE_ONCE to be
set as well for the same reasons.
marius [Fri, 15 Jan 2010 16:54:59 +0000 (16:54 +0000)]
MFC: r201396, r201410
- Demapping unused kernel TLB slots has proven to work reliably so move
the associated debugging under bootverbose.
- Remove freebsd4_sigreturn(); given that FreeBSD 4 didn't supported
sparc64 this only ever served as a transition aid prior to FreeBSD
5.0 and is unused by default since COMPAT_FREEBSD4 was removed from
GENERIC in r143072 nearly 5 years ago.
marius [Fri, 15 Jan 2010 16:46:03 +0000 (16:46 +0000)]
MFC: r201395
- Preserve the PROM IOMMU in order to allow OFW drivers to continue to
work.
- Sanity check the parameters passed to the implementations of the
pcib_{read,write}_config() methods. Using illegal values can cause
no real harm but it doesn't hurt to avoid unnecessary data error
traps requiring to flush and re-enable the level 1 caches.
marius [Fri, 15 Jan 2010 16:42:39 +0000 (16:42 +0000)]
MFC: r201199
- Prefer i and j over i and n for temporary integer variables.
- Wrap/shorten too long lines.
- Remove a redundant variable and an unnecessary cast in schizo(4).
marius [Fri, 15 Jan 2010 15:47:31 +0000 (15:47 +0000)]
MFC: r201005, r201371
- Take advantage of bus_{read,write}_*(9).
- Set dow = -1 in mk48txx_gettime() because some drivers (for example
the NetBSD and OpenBSD mk48txx(4)) don't set it correctly.
marius [Fri, 15 Jan 2010 15:38:49 +0000 (15:38 +0000)]
- Hook up the default implementations of the MSI/MSI-X pcib_if methods
so requests may bubble up to a host-PCI bridge driver.
- Distinguish between PCI and PCIe bridges in the device description
so it's a bit easier to follow what hangs off of what in the dmesg.
Unfortunately we can't also tell PCI and PCI-X apart based on the
information provided in the OFW device tree.
- Add quirk handling for the ALi M5249 found in Fire-based machines
which are used as a PCIe-PCIe bridge there. These are obviously
subtractive decoding as as they have a PCI-ISA bridge on their
secondary side (and likewise don't include the ISA I/O range in
their bridge decode) but don't indicate this via the class code.
Given that this quirk isn't likely to apply to all ALi M5249 and
I have no datasheet for these chips so I could implement a check
using the chip specific bits enabling subtractive decoding this
quirk handling is added to the MD code rather than the MI one.
marius [Fri, 15 Jan 2010 12:07:30 +0000 (12:07 +0000)]
MFC: r200944
Revert r183628 as with the current ata(4) ATAPI DMA with AcerLabs
M5229 appears to be once again fixed. If this happens to return
we probably should disable ATAPI DMA in ataacerlabs(4) instead
just like the Linux libATA does.
dougb [Fri, 15 Jan 2010 03:28:46 +0000 (03:28 +0000)]
MFC r200416:
Simplify handling of MTREEFILE relative to DESTDIR
Make the message about a missing MTREEFILE combined with -U
more informative
MFC r200425:
Over time things that used to be files/directories/links can change
to something else. So add code to detect when things don't match and
give the user choices about how to fix it.
If we're using -P and something in the above check needs to be moved
we need to have the directory there for it, so create it at the
beginning and delete empty versions of it at the end.
The case where something used to be a file or link and now is supposed
to be a directory (e.g., /etc/security) is especially dangerous, so
make failure to install a necessary directory in $DESTDIR a fatal error.
MFC r200700:
In the places where find is used that the user may see the results,
first pipe it to sort so that order of processing will be deterministic
and like things will be grouped together.
MFC r200701:
Fix an indentation issue, no functional changes
MFC r200708:
Fix a problem with how mergemaster handles the hard links for /.cshrc
and /.profile. The problem is that install(1) will unlink the old file
before it installs the new one, which means that in the best case we
have to compare the changes for the old file twice.
So, change the logic to first test to see if the link exists, then
install the file. Then if the link was there and we're using -i, just
create the link in /root and be done with it. Otherwise display the
message to the user and give them the option.
Because we are now sorting things before doing the comparison we can
know conclusively that the files in / should be the sources, and the
files in /root will be the targets, so adjust the paths accordingly.
While I'm here, split a too-long error message into two lines and
just return at the end of handling these files instead of setting
the variable that says "do nothing" and then returning at the end
of the function anyway.
MFC r201291:
Add some patches contributed by jhb:
1. Don't prompt the user for "-U but no db" error if we're using -a
2. Add an option to delete stale rc.d files automatically if the user
has DELETE_STALE_RC_FILES in their rc file. Lack of command line option
for this is not an oversight.
3. Add []'s around the terminal $ for the $FreeBSD$ test for -F
For one bug raised by jhb I did a more thorough solution:
There were a lot of things that "snuck in" between the end of the test
for -r and the start of the comparison. One of them is the creation of
the mtree db, as pointed out by jhb. Fix this problem more thoroughly
by moving the end of the test down to where it should/used to be, right
before the comparison. As a result, indent the interloping code to match.
MFC r201292:
Document the DELETE_STALE_RC_FILES option introduced in r201291. This is
an "rc file only" option by design.
While I'm here, update the comments in the example rc file to indicate
which command line options they relate to, and correct the defaults
for a couple of options.
MFC r201293:
It's not necessary to include both Op and Fl for command line options
included in the text, so use only the latter.
Clarify that using -U doesn't make sense in combination with -a
MFC r201323:
If we are using -p it does not make any sense to even create the
MTREENEW file since it will never be used.
MFC r201765:
Update copyright date
Update delete_temproot() to include the error message if it fails,
and clean up the places where it's called.
If there are no files left in temproot when the comparison is done
delete it without prompting. This should make "automated" runs of
mergemaster without -a a little easier.
yongari [Thu, 14 Jan 2010 22:26:52 +0000 (22:26 +0000)]
MFC r200950,200955,200965-200966,201767-201768
r200950:
Implement RX interrupt moderation using one-shot timer interrupt.
Unlike TX interrupt, ST201 does not provide any mechanism to
suppress RX interrupts. ste(4) can generate more than 70k RX
interrupts under heavy RX traffics such that these excessive
interrupts make system useless to process other useful things.
Maybe this was the major reason why polling support code was
introduced to ste(4).
The STE_COUNTDOWN register provides a programmable counter that
will generate an interrupt upon its expiration. We program
STE_DMACTL register to use 3.2us clock rate to drive the counter
register. Whenever ste(4) serves RX interrupt, the driver rearm
the timer to expire after STE_IM_RX_TIMER_DEFAULT time and disables
further generation of RX interrupts. This trick seems to work well
and ste(4) generates less than 8k RX interrupts even under 64 bytes
UDP torture test. Combined with TX interrupts, the total number of
interrupts are less than 10k which looks reasonable on heavily
loaded controller.
The default RX interrupt moderation time is 150us. Users can change
the value at any time with dev.ste.%d.int_rx_mod sysctl node.
Setting it 0 effectively disables the RX interrupt moderation
feature. Now we have both TX/RX interrupt moderation code so remove
loop of interrupt handler which resulted in sub-optimal performance
as well as more register accesses.
r200955:
Add suspend/resume support as well as basic WOL.
While I'm here simplify SIOCSIFCAP handler.
r200965:
Update if_iqdrops in case of RX buffer allocation failure.
r201767:
Fix EEPROM access code to return data in host byte order.
EEPROM on ST201 always returns 16bits data with little endian
format so conversion to host order is required.
This change fixes inversed ethernet address on sparc64.
r201768:
Make sure to store dma address of RX buffer in little endian form.
This fixes the last bug which keeps ste(4) from working on sparc64.
yongari [Thu, 14 Jan 2010 22:15:51 +0000 (22:15 +0000)]
MFC r200904-200908,200910-200913
r200904:
Don't reinitialize controller if driver is already running. This
reduces number of link state UP/DOWN changes.
r200905:
Reimplement controller reset. Datasheet says full reset takes about
1ms. Since we switched to memory register mapping make sure to
flush PCI posted write by reading the register again.
While I'm here add additional delays in loop while driver waits the
completion of the reset.
r200906:
Overhaul RX filter programming.
o Let RX filter handler program promiscuous/multicast filter as
well as broadcasting.
o Remove unnecessary register access.
o Simplify ioctl handler and have set_rxfilter to handle
IFF_PROMISC and IFF_ALLMULTI change instead of directly
programming the controller.
o Removed unnecessary error variable reinitialization in ioctl
handler.
o Add IFF_DRV_RUNNING check before programming multicast filter.
o Configure maximum allowed frame length before enabling MAC.
Datasheet didn't say the exact ordering of programming sequence
but it looks more natural to set maximum allowed frame length
first prior to enabling controller.
r200907:
Don't report link status if driver is not running.
r200908:
Report the correct result of mii_mediachg(). Previously it always
used to return success without respect to the result.
While I'm here use mii_mediachg() in ste_init_locked which allows
driver to use currently configured media. ste_ifmedia_upd() is
supposed to be called whenever user changes current media settings.
r200910:
Implement hardware MAC statistics counter support. The counters
could be accessed with dev.ste.0.stats sysctl node.
r200911:
Remove unused duplicated register definition. It seems the
definition was made to access STE_ASICCTL register as 16bits but
ste(4) always access the register as 32bits so it was never used
before.
r200912:
Correct STE_COUNTDOWN register offset. The datasheet was wrong.
r200913:
We don't need to generate DMA complete interrupt for every
transmitted frames. So request interrupt for every 16th frames. Due
to the limitation of hardware we can't suppress the interrupt as
driver should have to check TX status register. The TX status
register can store up to 31 TX status so driver can't send more
than 31 frames without reading TX status register.
With this change controller would not generate TX completion
interrupt for every frame, so reclaim transmitted frames in
ste_tick().
r200854:
Add minimal dealy while ste(4) is waiting for the end of active DMA
cycle.
r200856:
Introduce sc_flags member variable and use it to keep track of
link state and PHY related information.
Remove ste_link and ste_one_phy variable of softc as it's not used
anymore.
While I'm here add IFF_DRV_RUNNING check in ste_start_locked().
r200865:
Reimplement miibus_statchg method. Don't rely on link state change
interrupt. If we want to use link state change interrupt ste(4)
should also implement auto-negotiation complete handler as well as
various PHY access handling. Now link state change is handled by
mii(4) polling so it will automatically update link state UP/DOWN
events which in turn make ste(4) usable with lagg(4).
r199559 added a private timer to drive watchdog and the timer also
used to drive MAC statistics update. Because the MAC statistics
update is called whenever statistics counter reaches near-full, it
drove watchdog timer too fast such that it caused false watchdog
timeouts under heavy TX traffic conditions.
Fix the regression by separating ste_stats_update() from driving
watchdog timer and introduce a new function ste_tick() that handles
periodic job such as driving watchdog, MAC statistics update and
link state check etc.
While I'm here clear armed watchdog timer in ste_stop().
r200873:
Instead of relying on hard resetting of controller to stop
receiving incoming traffics, try harder to gracefully stop active
DMA cycles and then stop MACs. This is the way what datasheet
recommends and seems to work reliably. Resetting controller while
active DMAs are in progress is bad thing as we can't predict how
DMAs touche allocated TX/RX buffers. This change ensures controller
stop state before attempting to release allocated TX/RX buffers.
Also update MAC statistics which could have been updated during the
wait time of MAC stop.
While I'm here remove unnecessary controller resets in various
location. ste(4) no longer relies on hard controller reset to stop
controller and resetting controller also clears all configured
settings which makes it hard to implement WOL in near future.
Now resetting a controller is performed in ste_init_locked().
r200875:
Prefer memory space register mapping over io space. If memory space
mapping fails fall back to old io space mapping.
While I'm here use PCIR_BAR macro.
r200877:
Prefer bus_write_{1,2,4}/bus_read_{1,2,4} to
bus_space_write_{1,2,4}/bus_space_read_{1,2,4}.
Remove unused ste_bhandle and ste_btag in softc.
r200884:
Reimplement Tx status error handler as recommended by datasheet.
If ste(4) encounter TX underrun or excessive collisions the TX MAC
of controller is stalled so driver should wake it up again. TX
underrun requires increasing TX threshold value to minimize
further TX underruns. Previously ste(4) used to reset controller
to recover from TX underrun, excessive collision and reclaiming
error. However datasheet says only TX underrun requires resetting
entire controller. So implement ste_restart_tx() that restarts TX
MAC and do not perform full reset except TX underrun case.
Now ste(4) uses CSR_READ_2 instead of CSR_READ_1 to read
STE_TX_STATUS register. This way ste(4) will also read frame id
value and we can write the same value back to STE_TX_FRAMEID
register instead of overwriting it to 0. The datasheet was wrong
in write back of STE_TX_STATUS so add some comments why we do so.
Also always invoke ste_txeoc() after ste_txeof() in ste_poll as
without reading TX status register can stall TX MAC.
yongari [Thu, 14 Jan 2010 21:45:39 +0000 (21:45 +0000)]
MFC r200853:
Add bus_dma(9) and endianness support to ste(4).
o Sorted includes and added missing header files.
o Added basic endianness support. In theory ste(4) should work on
any architectures.
o Remove the use of contigmalloc(9), contigfree(9) and vtophys(9).
o Added 8 byte alignment limitation of TX/RX descriptor.
o Added 1 byte alignment requirement for TX/RX buffers.
o ste(4) controllers does not support DAC. Limit DMA address space
to be within 32bit address.
o Added spare DMA map to gracefully recover from DMA map failure.
o Removed dead code for checking STE_RXSTAT_DMADONE bit. The bit
was already checked in each iteration of loop so it can't be true.
o Added second argument count to ste_rxeof(). It is used to limit
number of iterations done in RX handler. ATM polling is the only
consumer.
o Removed ste_rxeoc() which was added to address RX stuck issue
(cvs rev 1.66). Unlike TX descriptors, ST201 supports chaining
descriptors to form a ring for RX descriptors. If RX descriptor
chaining is not supported it's possible for controller to stop
receiving incoming frames once controller pass the end of RX
descriptor which in turn requires driver post new RX
descriptors to receive more frames. For TX descriptors which
does not support chaning, we exactly do manual chaining in
driver by concatenating new descriptors to the end of previous
TX chain.
Maybe the workaround was borrowed from other drivers that does
not support RX descriptor chaining, which is not valid for ST201
controllers. I still have no idea how this address RX stuck
issue and I can't reproduce the RX stuck issue on DFE-550TX
controller.
o Removed hw.ste_rxsyncs sysctl as the workaround was removed.
o TX/RX side bus_dmamap_load_mbuf_sg(9) support.
o Reimplemented optimized ste_encap().
o Simplified TX logic of ste_start_locked().
o Added comments for TFD/RFD requirements.
o Increased number of RX descriptors to 128 from 64. 128 gave much
better performance than 64 under high network loads.
yongari [Thu, 14 Jan 2010 20:38:40 +0000 (20:38 +0000)]
Partial merge r199559:
- Add a private timer to drive the transmit watchdog instead of using
if_watchdog and if_timer.
- Fix some issues in detach for sn(4), ste(4), and ti(4). Primarily this
means calling ether_ifdetach() before anything else.
rmacklem [Thu, 14 Jan 2010 17:35:07 +0000 (17:35 +0000)]
MFC: r201345
Fix the experimental NFS client so that it can create Unix
domain sockets on an NFSv4 mount point. It was generating
incorrect XDR in the request for this case.
marius [Wed, 13 Jan 2010 21:23:27 +0000 (21:23 +0000)]
MFC: r200938
- Don't check for a valid interrupt controller on every interrupt
in intr_execute_handlers(). If we managed to get here without an
associated interrupt controller we have way bigger problems.
While at it predict stray vector interrupts as false as they are
rather unlikely.
- Don't blindly call the clear function of an interrupt controller
when adding a handler in inthand_add() as interrupt controllers
like the one driven by upa(4) are auto-clearing and thus provide
NULL instead.
marius [Wed, 13 Jan 2010 21:19:46 +0000 (21:19 +0000)]
MFC: r200925
- By re-arranging the code in OF_decode_addr() somewhat and accepting
a bit of a detour we can just iterate through the banks array instead
of having to calculate every offset. This change is inspired by the
powerpc version of this function.
- Add support for the JBus to EBus bridges which hang off of nexus(4).
marius [Wed, 13 Jan 2010 21:16:07 +0000 (21:16 +0000)]
MFC: r200923
- Add support for the IOMMUs of Fire JBus to PCIe and Oberon Uranus
to PCIe bridges.
- Add support for talking the PROM mappings over to the kernel IOTSB
just like we do with the kernel TSB in order to allow OFW drivers
to continue to work.
- Change some members, parameters and variables to unsigned where
more appropriate.
marius [Wed, 13 Jan 2010 21:12:27 +0000 (21:12 +0000)]
MFC: r200921
- Add quirk handling for ALi M5229, mainly setting the magic "force
enable IDE I/O" bit which prevents data access traps with revision
0xc8 in Fire-based machines when pci(4) enables PCIM_CMD_PORTEN.
- Like for sun4v also don't add the PCI side of host-PCIe bridges to
the bus on sun4u as they don't have configuration space implement
there either.
marius [Wed, 13 Jan 2010 21:03:04 +0000 (21:03 +0000)]
MFC: r200917
Hook ebus(4) and isa(4) up to the sun4v LINT build in order to
ensure that their compilation doesn't break as they are expected
to work as-is now (but aren't actually run-time tested).
marius [Wed, 13 Jan 2010 20:51:21 +0000 (20:51 +0000)]
MFC: r200915
Don't probe the bq4802 variant found in Ultra 25 and 45 for now as
this chip isn't MC146818 compatible and requires different handlers
(but which I can't test due to lack of such hardware).
marius [Wed, 13 Jan 2010 20:40:49 +0000 (20:40 +0000)]
MFC: r200914
Don't use an out register to hold the vector number across the call
of the interrupt handler in intr_fast() as the handler might clobber
it (no in-tree handler currently does but an upcoming one will).
While at it, tidy the register usage in the interrupt counting code.
marius [Wed, 13 Jan 2010 20:32:54 +0000 (20:32 +0000)]
MFC: r200879
- Add support for the JBus to EBus bridges which hang off of nexus(4)
and are found in sun4u and sun4v machines based on the Fire ASIC.
- Initialize the configuration space of the PCI to EBus variant the
same way as OpenSolaris does.
marius [Wed, 13 Jan 2010 20:07:45 +0000 (20:07 +0000)]
MFC: r200878
- Add macros for the states of the interrupt clear registers.
- Change INTMAP_VEC() to take an INO as its second argument rather
than an INR. The former is what I actually intended with this
macro and how it's currently used.
marius [Wed, 13 Jan 2010 20:03:24 +0000 (20:03 +0000)]
MFC: r200874
Enroll these drivers in multipass probing. The motivation behind this
is that the JBus to EBus bridges share the interrupt controller of a
sibling JBus to PCIe bridge (at least as far as the OFW device tree
is concerned, in reality they are part of the same chip) so we have to
probe and attach the latter first. That happens to be also the case
due to the fact that the JBus to PCIe bridges appear first in the OFW
device tree but it doesn't hurt to ensure the right order.
marius [Wed, 13 Jan 2010 19:55:51 +0000 (19:55 +0000)]
MFC: 197164
Factor out the duplicated macro for the device type used in the
OFW device tree for PCI bridges and add a new one for PCI Express.
While at it, take advantage of the former for the rman(9) work-
around in jbusppm(4).
jhb [Wed, 13 Jan 2010 18:12:21 +0000 (18:12 +0000)]
MFC 199607, 200797, 201270, 201669:
Use pthread_once() to initialize the thread-local storage for localtime()
and gmtime() and _once() to initialize gmt state rather than home-rolled
versions using pthread mutex locks.
jhb [Tue, 12 Jan 2010 19:55:07 +0000 (19:55 +0000)]
MFC 201215:
Add support for configuring vlan(4) interfaces as child devices similar to
wlan(4) interfaces. vlan(4) interfaces are listed via a new 'vlans_<IF>'
variable. If a vlan interface is a number, then that number is treated as
the vlan tag for the interface and the interface will be named '<IF>.<tag>'.
Otherwise, the vlan tag must be provided via a vlan parameter in a
'create_args_<vlan>' variable.
While I'm here, fix a few nits in rc.conf(5) and mention create_args_<IF> in
the description of cloned_interfaces.
brooks [Tue, 12 Jan 2010 06:11:36 +0000 (06:11 +0000)]
MFC r201954:
Update the comment on printing group membership to reflect that fact
that each group the process is a member of is printed rather than
an entry for each group the user could be a member of.
qingli [Tue, 12 Jan 2010 00:04:13 +0000 (00:04 +0000)]
MFC r201544
An existing incomplete ARP entry would expire a subsequent
statically configured entry of the same host. This bug was
due to the expiration timer was not cancelled when installing
the static entry. Since there exist a potential race condition
with respect to timer cancellation, simply check for the
LLE_STATIC bit inside the expiration function instead of
cancelling the active timer.
gallatin [Mon, 11 Jan 2010 20:32:51 +0000 (20:32 +0000)]
Sync mxge(4) with head:
r197391: Add support for TX throttling
r198250: Move mxge(4)'s NIC watchdog reset handler from
a callout to a taskqueue
r198303: Make mxge do a better job recovering from NIC h/w faults
r200845: Don't take the driver mutex in mxge_tick()
r201758: Remove extraneous semicolons
rmacklem [Mon, 11 Jan 2010 19:30:23 +0000 (19:30 +0000)]
MFC: r201029
When porting the experimental nfs subsystem to the FreeBSD8 krpc,
I added 3 functions that were already in the experimental client
under different names. This patch deletes the functions in the
experimental client and renames the calls to use the other set.
(This is just removal of duplicated code and does not fix any bug.)
jhb [Mon, 11 Jan 2010 18:42:29 +0000 (18:42 +0000)]
MFC 201522:
Expose the upper 256 ptys in the default devfs rules. I should have updated
this when expanding the old pty(4) driver to use 512 ptys by default. This
is more important for 7.x.
delphij [Mon, 11 Jan 2010 02:31:00 +0000 (02:31 +0000)]
MFC r201143:
Apply OpenSolaris revision 8021:b8fe9660eb2d which brings our zpool
to version 14, making it possible for zpools created on OpenSolaris
2009.06 be used on FreeBSD.
jilles [Sun, 10 Jan 2010 16:58:12 +0000 (16:58 +0000)]
MFC r210428: sh: Add a regression test that tries out all arithmetic ops.
The gaps in the numbering sequence cannot really be avoided, as HEAD changes
are not necessarily merged in the same order as they are made (if they are
merged at all).
fabient [Sun, 10 Jan 2010 16:04:32 +0000 (16:04 +0000)]
MFC 201023:
* Support the L1D_CACHE_LD event on Core2 processors.
* Correct a group of typos: for Core2 programmable events, check
user supplied umask values against the correct event descriptor
field.
yongari [Sat, 9 Jan 2010 01:17:31 +0000 (01:17 +0000)]
MFC r200693:
Make sure to enable Next Page bit for IP1001. Otherwise the PHY
fails to re-establishe 1000baseT link after downgrading to
10/100Mbps link.
yongari [Sat, 9 Jan 2010 00:36:28 +0000 (00:36 +0000)]
MFC r200641,200676
r200641:
Document newly added loader tunable and sysctl variables.
o hw.vge.msi_disable
o dev.vge.%d.int_holdoff
o dev.vge.%d.rx_coal_pkt
o dev.vge.%d.tx_coal_pkt
r200676:
Document more VIA Velocity family controllers to vge(4). Previously
it mentioned only VT6122. While I'm here remove the mention of
VT3119 which seems to be VIA's internal model name and VT3119
wouldn't be available to end users.
yongari [Sat, 9 Jan 2010 00:26:57 +0000 (00:26 +0000)]
MFC r200696,200740,200756,200758-200759,200972
r200696:
Add rudimentary WOL support. While I'm here remove enabling
busmastering/memory address in resume path. Bus driver will handle
that.
r200740:
Swap VGE_TXQTIMER and VGE_RXQTIMER register definition. Pending
timer for Tx queue is at 0x3E.
r200756:
Correct fragment bit definition in comments.
r200758:
VT6130 datasheet was wrong. If VT6130 receive a jumbo frame the
controller will split the jumbo frame into multiple RX buffers.
However it seems the hardware always dma the frame to 8 bytes
boundary for the split frames. Only the first part of the fragment
can have 4 byte alignment and subsequent buffers should be 8 bytes
aligned. Change RX buffer the alignment requirement to 8 bytes from
4 bytes.
r200759:
Disable jumbo frame support for PCIe VT6130/VT6132 controllers.
Quite contrary to VT6130 datasheet which says it supports up to 8K
jumbo frame, VT6130 does not seem to send jumbo frame that is
larger than 4K in length. Trying to send a frame that is larger
than 4K cause TX MAC hang.
Even though it's possible to allow 4K jumbo frame for VT6130, I
think it's meaningless to allow 4K jumbo frame. I'm not sure VT6132
also has the same limitation but I guess it uses the same MAC of
VT6130.
yongari [Sat, 9 Jan 2010 00:17:43 +0000 (00:17 +0000)]
MFC r200638:
Implement interrupt moderation scheme supported by VT61xx
controllers. TX/RX interrupt mitigation is controlled by
VGE_TXSUPPTHR and VGE_RXSUPPTHR register. These registers suppress
generation of interrupts until the programmed frames counter equals
to the registers. VT61xx also supports interrupt hold off timer
register. If this interrupt hold off timer is active all interrupts
would be disabled until the timer reaches to 0. The timer value is
reloaded whenever VGE_ISR register written. The timer resolution is
about 20us.
Previously vge(4) used single shot timer to reduce Tx completion
interrupts. This required VGE_CRS1 register access in Tx
start/completion handler to rearm new timeout value and it did not
show satisfactory result(more than 50k interrupts under load). Rx
interrupts was not moderated at all such that vge(4) used to
generate too many interrupts which in turn made polling(4) better
approach under high network load.
This change activates all interrupt moderation mechanism and
initial values were tuned to generate interrupt less than 8k per
second. That number of interrupts wouldn't add additional packet
latencies compared to polling(4). These interrupt parameters could
be changed with sysctl.
dev.vge.%d.int_holdoff
dev.vge.%d.rx_coal_pkt
dev.vge.%d.tx_coal_pkt
Interface has be brought down and up again before change take
effect.
With interrupt moderation there is no more need to loop in
interrupt handler. This loop always added one more register access.
While I'm here remove dead code which tried to implement subset of
interrupt moderation.
yongari [Sat, 9 Jan 2010 00:12:59 +0000 (00:12 +0000)]
MFC r200616-200617,200635,200639,200644
r200616:
Add new flag VGE_FLAG_SUSPENDED to mark suspended state and
remove suspended member in softc.
r200617:
Add "Velocity" to probe message which will make it clearer which
ethernet controller was recognized. VIA consistently calls
"Velocity" family for gigabit ethernet controllers. For fast
ethernet controllers they uses "Rhine" family(vr(4) controllers))
and vr(4) already shows "Rhine" in probe message.
yongari [Sat, 9 Jan 2010 00:02:40 +0000 (00:02 +0000)]
MFC r200551-200552,200555,200558,200609,200613
r200551:
Whenever link state change interrupt is raised, vge_tick() is
called and vge(4) used to drive auto-negotiation timer(mii_tick) in
vge_tick(). Therefore the mii_tick was not called for every hz such
that auto-negotiation complete was never handled in vge(4).
Use mii_pollstat to extract current negotiated speed/duplex instead
of mii_tick. The latter is valid only for auto-negotiation case.
While I'm here change the confusing function name vge_tick() to
vge_link_statchg().
r200552:
Report media change result to caller instead of returning success
without regard to the result.
r200555:
Don't report current link status if interface is not UP.
If interface is not UP, the current link status wouldn't
reflect the negotiated status.
r200558:
Tell upper layer vge(4) supports long frames. This should be done
after ether_ifattach(), as ether_ifattach() initializes it with
ETHER_HDR_LEN.
While I'm here remove setting if_mtu, it's already handled in
ether_ifattach().
r200609:
All vge(4) controllers support RX/TX checksum offloading for VLAN
tagged frames so add checksum offloading capabilities. Also add
missing VLAN hardware tagging control in ioctl handler and let
upper stack know current VLAN capabilities.
r200613:
Rewrite RX filter setup and simplify code.
Now promiscuous mode and multicast handling is performed in single
function, vge_rxfilter().
yongari [Fri, 8 Jan 2010 22:26:24 +0000 (22:26 +0000)]
MFC r200538,200540-200541,200543,200545,200548
r200538:
Introduce vge_flags member in softc. The vge_flags member will
record device specific bits. Remove vge_link and use vge_flags.
While here, move clearing link state before mii_mediachg() as
mii_mediachg() may affect link state.
r200540:
Save PHY address by reading VGE_MIICFG register. For PCIe
controllers(VT613x), we assume the PHY address is 1.
Use the saved PHY address in MII register access routines and
remove accessing VGE_MIICFG register.
While I'm here save PCI express capability register which will be
used in near future.
r200541:
Add MSI support for VT613x controllers.
r200543:
Increase output queue size from 64 to 255.
r200545:
We don't have to reload EEPROM in vge_reset(). Because vge_reset()
is called in vge_init_lock(), vge(4) always used to reload EEPROM.
Also add more comment why vge(4) clears VGE_CHIPCFG0_PACPI bit.
While I'm here add missing new line in vge_reset().
yongari [Fri, 8 Jan 2010 22:08:18 +0000 (22:08 +0000)]
MFC r200526-200527,200529,200531-200533,200536
r200526:
Use PCIR_BAR instead of hard-coded value.
r200527:
Fix typo in register definition.
r200529:
Clear VGE_TXDESC_Q bit for transmitted frames. The VGE_TXDESC_Q bit
seems to work like a tag that indicates 'not list end' of queued
frames. Without having a VGE_TXDESC_Q bit indicates 'list end'. So
the last frame of multiple queued frames has no VGE_TXDESC_Q bit.
The hardware has peculiar behavior for VGE_TXDESC_Q bit handling.
If the VGE_TXDESC_Q bit of descriptor was set the controller would
fetch next descriptor. However if next descriptor's OWN bit was
cleared but VGE_TXDESC_Q was set, it could confuse controller.
Clearing VGE_TXDESC_Q bit for transmitted frames ensure correct
behavior.
yongari [Fri, 8 Jan 2010 21:37:16 +0000 (21:37 +0000)]
MFC r200525:
Overhaul bus_dma(9) usage and fix various things.
o Separate TX/RX buffer DMA tag from TX/RX descriptor ring DMA tag.
o Separate RX buffer DMA tag from common buffer DMA tag. RX DMA
tag has different restriction compared to TX DMA tag.
o Add 40bit DMA address support.
o Adjust TX/RX descriptor ring alignment to 64 bytes from 256
bytes as documented in datasheet.
o Added check to ensure TX/RX ring reside within a 4GB boundary.
Since TX/RX ring shares the same high address register they
should have the same high address.
o TX/RX side bus_dmamap_load_mbuf_sg(9) support.
o Add lock assertion to vge_setmulti().
o Add RX spare DMA map to recover from DMA map load failure.
o Add optimized RX buffer handler, vge_discard_rxbuf which is
activated when vge(4) sees bad frames.
o Don't blindly update VGE_RXDESC_RESIDUECNT register. Datasheet
says the register should be updated only when number of
available RX descriptors are multiple of 4.
o Use __NO_STRICT_ALIGNMENT instead of defining VGE_FIXUP_RX which
is only set for i386 architecture. Previously vge(4) also
performed expensive copy operation to align IP header on amd64.
This change should give RX performance boost on amd64
architecture.
o Don't reinitialize controller if driver is already running. This
should reduce number of link state flipping.
o Since vge(4) drops a driver lock before passing received frame
to upper layer, make sure vge(4) is still running after
re-acquiring driver lock.
o Add second argument count to vge_rxeof(). The argument will
limit number of packets could be processed in RX handler.
o Rearrange vge_rxeof() not to allocate RX buffer if received
frame was bad packet.
o Removed if_printf that prints DMA map failure. This type of
message shouldn't be used in fast path of driver.
o Reduce number of allowed TX buffer fragments to 6 from 7. A TX
descriptor allows 7 fragments of a frame. However the CMZ field
of descriptor has just 3bits and the controller wants to see
fragment + 1 in the field. So if we have 7 fragments the field
value would be 0 which seems to cause unexpected results under
certain conditions. This change should fix occasional TX hang
observed on vge(4).
o Simplify vge_stat_locked() and add number of available TX
descriptor check.
o vge(4) controllers lack padding short frames. Make sure to fill
zero for the padded bytes. This closes unintended information
disclosure.
o Don't set VGE_TDCTL_JUMBO flag. Datasheet is not clear whether
this bit should be set by driver or write-back status bit after
transmission. At least vendor's driver does not set this bit so
remove it. Without this bit vge(4) still can send jumbo frames.
o Don't start driver when vge(4) know there are not enough RX
buffers.
o Remove volatile keyword in RX descriptor structure. This should
be handled by bus_dma(9).
o Collapse two 16bits member of TX/RX descriptor into single 32bits
member.
o Reduce number of RX descriptors to 252 from 256. The
VGE_RXDESCNUM is 16bits register but only lower 8bits are valid.
So the maximum number of RX descriptors would be 255. However
the number of should be multiple of 4 as controller wants to
update 4 RX descriptors at a time. This limits the maximum
number of RX descriptor to be 252.
yongari [Fri, 8 Jan 2010 21:15:09 +0000 (21:15 +0000)]
MFC r198987,199414,199543,200422
Partial merge r198987:
Use device_printf() and if_printf() instead of printf() with an explicit
unit number and remove 'unit' members from softc.
Partial merge r199414:
Use the bus_*() routines rather than bus_space_*() for register operations.
r199543:
Several fixes to this driver:
- Overhaul the locking to avoid recursion and add missing locking in a few
places.
- Don't schedule a task to call vge_start() from contexts that are safe to
call vge_start() directly. Just invoke the routine directly instead
(this is what all of the other NIC drivers I am familiar with do). Note
that vge(4) does not use an interrupt filter handler which is the primary
reason some other drivers use tasks.
- Add a new private timer to drive the watchdog timer instead of using
if_watchdog and if_timer.
- Fixup detach by calling ether_ifdetach() before stopping the interface.
r200422:
Remove driver lock assertion in MII register access. This change
was made in r199543 to remove MTX_RECURSE. These routines can be
called in device attach phase(e.g. mii_phy_probe()) so checking
assertion here is not right as caller does not hold a driver lock.
projects / FreeBSD / stable / 8.git / log