grehan [Thu, 16 Feb 2017 17:08:43 +0000 (17:08 +0000)]
MFC r311702
Use correct PCI device id for virtio-rng.
This prevented the device from attaching with a
Windows guest (most other guests use the device type
for matching)
garga [Thu, 16 Feb 2017 09:19:29 +0000 (09:19 +0000)]
MFC r313477:
Cleanup on usr.sbin/arp/arp.c
* 'blackhole' and 'reject' are mutually exclusive, replace printf() by errx()
when both are selected.
* 'trail' option is no longer supported since first import of arp from 4.4BSD.
XXX message was added 13 years ago in r128192. I believe it's time to remove
it.
* Use warnx() to print some informative messages instead of printf()
* Replace strncmp() by strcmp() when validating parameters and exit when invalid
parameter is found
ngie [Thu, 16 Feb 2017 05:14:07 +0000 (05:14 +0000)]
MFC r285119,r292502,r295380:
r285119 (by jmmv):
Add support for TEST_METADATA
Allow Makefiles to define generic metadata settings that apply to all test
programs defined by a Makefile. The generic TEST_METADATA variable extends
the per-test program settings already supported via TEST_METADATA.<program>.
This feature will be useful to easily apply some settings to all programs
in a directory. In particular, Kyua 0.12 will support parallel execution
of test programs and a bunch of them will need to be tagged as is_exclusive
to indicate that they cannot be run in parallel with anything else due to
their side-effects. It will be reasonable to set this setting on whole
directories.
r292502:
Always expose LOCALBASE, not just when CROSS_TOOLCHAIN is defined
Instead of using which(1) to look for doxygen, look for it in <LOCALBASE>/bin .
$PATH gets mangled by make buildenv, etc so it's better to just be explicit
about the path if someone uses that for instance.
r295380:
Simplify running the FreeBSD test suite
Replace `make regress` (legacy test make target) and `make test` (incomplete
test make target added with the FreeBSD test suite) with make check as it's
consistent with other open source projects.
`make check` defaults to running tests from `.OBJDIR`, but can be overridden
with the `CHECKDIR` variable.
Add `make checkworld` target to simplify running the FreeBSD test suite from
`TESTSBASE` (i.e. the top-level tests directory), similar to buildworld.
Document `make check` and `make checkworld` in build(7).
Other minor changes:
- Rename intermediate file (`Kyuafile.auto`) to `Kyuafile` to simplify
`make check`.
- Remove terse warnings attached to `beforetest`/`aftertest`.
- Add kyua binary check to check target in suite.test.mk; error out if it's
not found
The MFC is [partly] contingent on other build related changes being MFCed.
ngie [Thu, 16 Feb 2017 04:23:45 +0000 (04:23 +0000)]
MFC r288241:
r288241 (by bdrewery):
Remove 'set -e' that are no longer needed as it is already default.
When bmake was initially imported at r241298 shell commands were no longer
ran with 'set -e' as they were before. This was fixed in r254980 so they
again always use 'set -e'.
garga [Wed, 15 Feb 2017 09:15:51 +0000 (09:15 +0000)]
MFC r313448:
bsdinstall: Make sure chroot filesystems are umounted after use
* DISTDIR_IS_UNIONFS is set every time BSDINSTALL_DISTDIR is mounted inside
BSDINSTALL_CHROOT. Use this flag to decide if it needs to be umounted
* BSDINSTALL_CHROOT/dev is mounted when 'bsdinstall mount' is called, there is
no need to mount it again when user goes to shell after installation
asomers [Wed, 15 Feb 2017 00:16:52 +0000 (00:16 +0000)]
MFC r311893, r313008, r313081
I had to modify the tests slightly for the MFC to stable/10, because
stable/10 lacks r294037, which enabled /sbin/md5 to work on md(4)
devices.
r311893:
ATFify the geom gate tests.
This ensures their cleanup routines will be run even if they should timeout.
tests/sys/geom/class/gate/ggate_test.sh
tests/sys/geom/class/gate/Makefile
Add an ATF test with three testcases, one for each TAP test. Use
ATF-style cleanup functions, and convert sleeps to polling loops.
ObsoleteFiles.inc
tests/sys/geom/class/gate/conf.sh
tests/sys/geom/class/gate/1_test.sh
tests/sys/geom/class/gate/2_test.sh
tests/sys/geom/class/gate/3_test.sh
Delete TAP test files
r313008:
Wait for /dev/ggate* to appear after calling `ggatel create` in :ggatel_{file,md}
The test assumed that `ggatel create` created a device on completion, but that's
incorrect. This squashes the race by waiting for the device to appear, as
`ggatel create` daemonizes before issuing an ioctl to geom_gate(4) if not called
with `-v`.
r313081:
Replace for/retry loops with "wait_for_ggate_device" calls and check
results of commands
As noted in r313008, the underlying issue was that geom_gate device
creation wasn't created at ggatel command completion, but some short
time after. ggatec(8) employs similar logic when creating geom_gate(4)
devices.
Switch from retry loops (after the ggatec/dd write calls) to
wait_for_ggate_device function calls after calling ggatec(8) instead
to detect the presence of the /dev/ggate* device, as this function is
sufficient for determining whether or not the character device is ready
for testing
While here, use atf_check consistently with all dd calls to ensure that
data output is as expected.
ngie [Tue, 14 Feb 2017 04:49:24 +0000 (04:49 +0000)]
MFC r313378,r313379:
r313378:
Wrap strcmp/wcscmp calls with ATF_CHECK_MSG and drop atf_tc_fail use
The reasoning here was the same as what was done in r313376:
- Gather as many results as possible instead of failing early and
not testing the rest of the cases.
- Simplify logic when checking test inputs vs outputs and printing
test result.
r313379:
Expect :int_within_limits to fail when ptrdiff_t/*intmax_t differ in base type
The %t{d,u} (ptrdiff_t) tests fail for the following reasons:
- ptrdiff_t is by definition int32_t on !LP64 architectures and int64_t on
LP64 architectures.
- intmax_t is by definition fixed to int64_t on all architectures.
- Some of the code in lib/libc/stdio/... is promoting ptrdiff_t to *intmax_t
when parsing/representing the value.
ngie [Tue, 14 Feb 2017 04:46:19 +0000 (04:46 +0000)]
MFC r313376:
Fix :hexadecimal_floating_point on i386
Don't exclude i386 from LDBL_MANT_DIG == 64; it works properly in
that case.
While here, replace strcmp + atf_tc_fail with ATF_CHECK_MSG for 2
reasons:
- Gather as many results as possible instead of failing early and
not testing the rest of the cases.
- Simplify logic when checking test inputs vs outputs and printing
test result.
ken [Mon, 13 Feb 2017 16:11:37 +0000 (16:11 +0000)]
MFC r313568:
------------------------------------------------------------------------
r313568 | ken | 2017-02-10 15:02:45 -0700 (Fri, 10 Feb 2017) | 68 lines
Change the isp(4) driver to not adjust the tag type for REQUEST SENSE.
The isp(4) driver was changing the tag type for REQUEST SENSE
commands to Head of Queue, when the CAM CCB flag
CAM_TAG_ACTION_VALID was NOT set. CAM_TAG_ACTION_VALID is set
when the tag action in the XPT_SCSI_IO is not CAM_TAG_ACTION_NONE
and when the target has tagged queueing turned on.
In most cases when CAM_TAG_ACTION_VALID is not set, it is because
the target is not doing tagged queueing. In those cases, trying to
send a Head of Queue tag may cause problems. Instead, default to
sending a simple tag.
IBM tape drives claim to support tagged queueing in their standard
Inquiry data, but have the DQue bit set in the control mode page
(mode page 10). CAM correctly detects that these drives do not
support tagged queueing, and clears the CAM_TAG_ACTION_VALID flag
on CCBs sent down to the drives.
This caused the isp(4) driver to go down the path of setting the
tag action to a default value, and for Request Sense commands only,
set the tag action to Head of Queue.
If an IBM tape drive does get a Head of Queue tag, it rejects it with
Invalid Message Error (0x49,0x00). (The Qlogic firmware translates that
to a Transport Error, which the driver translates to an Unrecoverable
HBA Error, or CAM_UNREC_HBA_ERROR.) So, by default, it wasn't possible
to get a good response from a REQUEST SENSE to an FC-attached IBM
tape drive with the isp(4) driver.
IBM tape drives (tested on an LTO-5 with G9N1 firmware and a TS1150
with 4470 firmware) also have a bug in that sending a command with a
non-simple tag attribute breaks the tape drive's Command Reference
Number (CRN) accounting and causes it to ignore all subsequent
commands because it and the initiator disagree about the next
expected CRN. The drives do reject the initial command with a head
of queue tag with an Invalid Message Error (0x49,0x00), but after that
they ignore any subsequent commands. IBM confirmed that it is a bug,
and sent me test firmware that fixes the bug. However tape drives in
the field will still exhibit the bug until they are upgraded.
Request Sense is not often sent to targets because most errors are
reported automatically through autosense in Fibre Channel and other
modern transports. ("Modern" meaning post SCSI-2.) So this is not
an error that would crop up frequently. But Request Sense is useful on
tape devices to report status information, aside from error reporting.
This problem is less serious without FC-Tape features turned on,
specifically precise delivery of commands (which enables Command
Reference Numbers), enabled on the target and initiator. Without
FC-Tape features turned on, the target would return an error and
things would continue on.
And it also does not cause problems for targets that do tagged
queueing, because in those cases the isp(4) driver just uses the
tag type that is specified in the CCB, assuming the
CAM_TAG_ACTION_VALID flag is set, and defaults to sending a Simple
tag action if it isn't an ordered or head of queue tag.
sys/dev/isp/isp.c:
In isp_start(), don't try to send Request Sense commands
with the Head of Queue tag attribute if the CCB doesn't
have a valid tag action. The tag action likely isn't valid
because the target doesn't support tagged queueing.
jilles [Sun, 12 Feb 2017 18:52:01 +0000 (18:52 +0000)]
MFC r313174: Clean up documentation of AF_UNIX control messages.
Document AF_UNIX control messages in unix(4) only, not split between unix(4)
and recv(2).
Also, warn about LOCAL_CREDS effective uid/gid fields, since the write could
be from a setuid or setgid program (with the explicit SCM_CREDS and
LOCAL_PEERCRED, the credentials are read at such a time that it can be
assumed that the process intends for them to be used in this context).
cy [Sat, 11 Feb 2017 18:10:55 +0000 (18:10 +0000)]
MFC r311950 (by bz):
Get rid of a compiler warning which I saw too often.
Include netinet/in.h before ip_compat.t which will then check if
IPPROTO_IPIP is defined or not. Doing it the other way round,
ip_compat.h would not find it defined and netinet/in.h then
redefine it.
mm [Sat, 11 Feb 2017 00:56:18 +0000 (00:56 +0000)]
MFC r310866,310868,310870,311903,313074:
Sync libarchive with vendor.
MFC r310866:
PR #771: Add NFSv4 ACL support to pax and restricted pax
NFSv4 ACL information may now be stored to and restored from tar archives.
ACL must be non-trivial and supported by the underlying filesystem, e.g.
natively by ZFS or by UFS with the NFSv4 ACL enable flag set.
MFC r310868:
PR #843: Fix memory leak of struct archive_entry in cpio/cpio.c
PR #851: Spelling fixes
Fix two protoypes in manual page archive_read_disk.3
MFC r310870:
Use __LA_DEPRECATED macro with functions deprecated in 379867e
MFC r311903:
#691: Support for SCHILY.xattr extended attributes
#854: Spelling fixes
Multiple fixes in ACL code:
- prefer acl_set_fd_np() to acl_set_fd()
- if acl_set_fd_np() fails, do no fallback to acl_set_file()
- do not warn if trying to write ACLs to a filesystem without ACL support
- fix id handling in archive_acl_(from_to)_text*() for NFSv4 ACLs
MFC r313074:
- support extracting NFSv4 ACLs from Solaris tar archives
- bugfixes and optimizations in the ACL code
- multiple fixes in the test suite
- typo and other small bugfixes
Security fixes:
- cab reader: endless loop when parsing MSZIP signature (OSS-Fuzz 335)
- LHA reader: heap-buffer-overflow in lha_read_file_header_1()
(CVE-2017-5601)
- LZ4 reader: null-pointer dereference in lz4_filter_read_legacy_stream()
(OSS-Fuzz 453)
- mtree reader: heap-buffer-overflow in detect_form() (OSS-Fuzz 421, 443)
- WARC reader: heap-buffer-overflow in xstrpisotime() (OSS-Fuzz 382, 458)
Memory leak fixes:
- ACL support: free memory allocated by acl_get_qualifier()
- disk writer: missing free in create_filesystem_object()
- file reader: fd leak (Coverity 1016755)
- gnutar writer: fix free in archive_write_gnutar_header()
(Coverity 101675)
- iso 9660 reader: missing free in parse_file_info()
(partial Coverity 1016754)
- program reader: missing free in __archive_read_program()
- program writer: missing free in __archive_write_program_free()
- xar reader: missing free in xar_cleanup()
- xar reader: missing frees in expat_xmlattr_setup()
(Coverity 1229979-1229981)
- xar writer: missing free in file_free()
- zip reader: missing free in zip_read_local_file_header()
List of all libarchive issues at OSS-Fuzz:
https://bugs.chromium.org/p/oss-fuzz/issues/list?can=1&q=libarchive
vangyzen [Fri, 10 Feb 2017 16:11:11 +0000 (16:11 +0000)]
MFC r313401
Fix garbage IP addresses in UDP log_in_vain messages
If multiple threads emit a UDP log_in_vain message concurrently,
or indeed call inet_ntoa() for any other reason,
the IP addresses could be garbage due to concurrent usage of a
single string buffer inside inet_ntoa(). Use inet_ntoa_r() with
two stack buffers instead.
projects / FreeBSD / stable / 10.git / log