1 .\" Copyright (c) 1997, 1998, 1999
2 .\" Bill Paul <wpaul@ctr.columbia.edu>. All rights reserved.
4 .\" Redistribution and use in source and binary forms, with or without
5 .\" modification, are permitted provided that the following conditions
7 .\" 1. Redistributions of source code must retain the above copyright
8 .\" notice, this list of conditions and the following disclaimer.
9 .\" 2. Redistributions in binary form must reproduce the above copyright
10 .\" notice, this list of conditions and the following disclaimer in the
11 .\" documentation and/or other materials provided with the distribution.
12 .\" 3. All advertising materials mentioning features or use of this software
13 .\" must display the following acknowledgement:
14 .\" This product includes software developed by Bill Paul.
15 .\" 4. Neither the name of the author nor the names of any co-contributors
16 .\" may be used to endorse or promote products derived from this software
17 .\" without specific prior written permission.
19 .\" THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
20 .\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
21 .\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
22 .\" ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
23 .\" BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
24 .\" CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
25 .\" SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
26 .\" INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
27 .\" CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
28 .\" ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
29 .\" THE POSSIBILITY OF SUCH DAMAGE.
38 .Nd "SysKonnect SK-984x and SK-982x PCI Gigabit Ethernet adapter driver"
40 To compile this driver into the kernel,
41 place the following lines in your
42 kernel configuration file:
43 .Bd -ragged -offset indent
48 Alternatively, to load the driver as a
49 module at boot time, place the following line in
51 .Bd -literal -offset indent
57 driver provides support for the SysKonnect SK-984x and SK-982x series PCI
58 Gigabit Ethernet adapters.
60 The SysKonnect adapters consist of two main components: the XaQti Corp.
61 XMAC II gigabit MAC and the SysKonnect GEnesis controller ASIC.
63 XMAC provides the gigabit MAC and PHY support while the GEnesis
64 provides an interface to the PCI bus, DMA support, packet buffering
66 The GEnesis can control up to two XMACs simultaneously,
67 allowing dual-port NIC configurations.
69 The SK-982x 1000baseT adapters also include a Broadcom BCM5400 1000baseTX
70 PHY which is used in place of the XMAC's internal PHY.
71 The Broadcom PHY is connected to the XMAC via its GMII port.
75 driver configures dual port SysKonnect adapters such that each XMAC
76 is treated as a separate logical network interface.
78 operate independently of each other and can be connected to separate
80 The SysKonnect driver software currently only uses the
81 second port on dual port adapters for failover purposes: if the link
82 on the primary port fails, the SysKonnect driver will automatically
83 switch traffic onto the second port.
85 Also supported is the Marvell Semiconductor 88E100* gigabit PHY.
87 The XaQti XMAC II supports full and half duplex operation with
89 The XMAC also supports unlimited frame sizes.
90 Support for jumbo frames is provided via the interface MTU setting.
91 Selecting an MTU larger than 1500 bytes with the
93 utility configures the adapter to receive and transmit jumbo frames.
94 Using jumbo frames can greatly improve performance for certain tasks,
95 such as file transfers and data streaming.
99 driver supports the following media types:
101 .Bl -tag -width xxxxxxxxxxxxxxxxxxxx
103 Enable autoselection of the media type and options.
104 The user can manually override
105 the autoselected mode by adding media options to the
109 Set 1000baseTX operation over twisted pair.
110 This is only available
111 for SK-982x series adapters with 1000baseT ports.
118 Set 1000Mbps (Gigabit Ethernet) operation.
128 driver supports the following media options:
130 .Bl -tag -width xxxxxxxxxxxxxxxxxxxx
132 Force full duplex operation
134 Force half duplex operation.
137 For more information on configuring this device, see
140 Adapters supported by the
146 3Com 3C940 single port, 1000baseT adapter
148 3Com 3C2000-T single port, 1000baseT adapter
150 Belkin F5D5005 single port, 1000baseT adapter
152 D-Link DGE-530T single port, 1000baseT adapter
154 Linksys (revision 2) single port, 1000baseT adapter
156 SK-9521 SK-NET GE-T single port, 1000baseT adapter
158 SK-9821 SK-NET GE-T single port, 1000baseT adapter
160 SK-9822 SK-NET GE-T dual port, 1000baseT adapter
162 SK-9841 SK-NET GE-LX single port, single mode fiber adapter
164 SK-9842 SK-NET GE-LX dual port, single mode fiber adapter
166 SK-9843 SK-NET GE-SX single port, multimode fiber adapter
168 SK-9844 SK-NET GE-SX dual port, multimode fiber adapter
170 SMC 9452TX single port, 1000baseT adapter
173 Tunables can be set at the
175 prompt before booting the kernel or stored in
177 .Bl -tag -width xxxxxx
178 .It Va hw.skc.jumbo_disable
179 Disable jumbo frame support.
180 Systems with less memory can set it to a non-zero value to save memory.
181 The default value is 0.
184 The following variable is available as both
189 .Bl -tag -width xxxxxx
190 .It Va dev.skc.%d.int_mod
191 This variable controls interrupt moderation.
192 The accepted range is 10 to 10000.
193 The default value is 100 microseconds.
194 The interface has to be brought down and up again before a change takes effect.
198 .It "sk%d: couldn't map memory"
199 A fatal initialization error has occurred.
200 .It "sk%d: couldn't map ports"
201 A fatal initialization error has occurred.
202 .It "sk%d: couldn't map interrupt"
203 A fatal initialization error has occurred.
204 .It "sk%d: no memory for softc struct!"
205 The driver failed to allocate memory for per-device instance information
206 during initialization.
207 .It "sk%d: failed to enable memory mapping!"
208 The driver failed to initialize PCI shared memory mapping.
210 happen if the card is not in a bus-master slot.
211 .It "sk%d: no memory for jumbo buffers!"
212 The driver failed to allocate memory for jumbo frames during
214 .It "sk%d: watchdog timeout"
215 The device has stopped responding to the network, or there is a problem with
216 the network connection (cable).
227 .%T XaQti XMAC II datasheet
228 .%O http://www.xaqti.com
231 .%T SysKonnect GEnesis programming manual
232 .%O http://www.syskonnect.com
237 device driver first appeared in
242 driver was written by
243 .An Bill Paul Aq wpaul@ctr.columbia.edu .