2 * Copyright (c) 2016 Jared McNeill <jmcneill@invisible.ca>
4 * Redistribution and use in source and binary forms, with or without
5 * modification, are permitted provided that the following conditions
7 * 1. Redistributions of source code must retain the above copyright
8 * notice, this list of conditions and the following disclaimer.
9 * 2. Redistributions in binary form must reproduce the above copyright
10 * notice, this list of conditions and the following disclaimer in the
11 * documentation and/or other materials provided with the distribution.
13 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
14 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
15 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
16 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
17 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
18 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
19 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
20 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
21 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
22 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
29 * Allwinner RSB (Reduced Serial Bus) and P2WI (Push-Pull Two Wire Interface)
32 #include <sys/cdefs.h>
33 __FBSDID("$FreeBSD$");
35 #include <sys/param.h>
36 #include <sys/systm.h>
39 #include <sys/kernel.h>
41 #include <sys/module.h>
42 #include <sys/mutex.h>
43 #include <machine/bus.h>
45 #include <dev/ofw/ofw_bus.h>
46 #include <dev/ofw/ofw_bus_subr.h>
48 #include <dev/iicbus/iiconf.h>
49 #include <dev/iicbus/iicbus.h>
51 #include <dev/extres/clk/clk.h>
52 #include <dev/extres/hwreset/hwreset.h>
54 #include "iicbus_if.h"
57 #define START_TRANS (1 << 7)
58 #define GLOBAL_INT_ENB (1 << 1)
59 #define SOFT_RESET (1 << 0)
63 #define INT_TRANS_ERR_ID(x) (((x) >> 8) & 0xf)
64 #define INT_LOAD_BSY (1 << 2)
65 #define INT_TRANS_ERR (1 << 1)
66 #define INT_TRANS_OVER (1 << 0)
67 #define INT_MASK (INT_LOAD_BSY|INT_TRANS_ERR|INT_TRANS_OVER)
68 #define RSB_DADDR0 0x10
69 #define RSB_DADDR1 0x14
71 #define DLEN_READ (1 << 4)
72 #define RSB_DATA0 0x1c
73 #define RSB_DATA1 0x20
83 #define DAR_RTA (0xff << 16)
84 #define DAR_RTA_SHIFT 16
85 #define DAR_DA (0xffff << 0)
86 #define DAR_DA_SHIFT 0
89 #define RSB_RESET_RETRY 100
90 #define RSB_I2C_TIMEOUT hz
92 #define RSB_ADDR_PMIC_PRIMARY 0x3a3
93 #define RSB_ADDR_PMIC_SECONDARY 0x745
94 #define RSB_ADDR_PERIPH_IC 0xe89
99 static struct ofw_compat_data compat_data[] = {
100 { "allwinner,sun6i-a31-p2wi", A31_P2WI },
101 { "allwinner,sun8i-a23-rsb", A23_RSB },
105 static struct resource_spec rsb_spec[] = {
106 { SYS_RES_MEMORY, 0, RF_ACTIVE },
111 * Device address to Run-time address mappings.
113 * Run-time address (RTA) is an 8-bit value used to address the device during
114 * a read or write transaction. The following are valid RTAs:
115 * 0x17 0x2d 0x3a 0x4e 0x59 0x63 0x74 0x8b 0x9c 0xa6 0xb1 0xc5 0xd2 0xe8 0xff
117 * Allwinner uses RTA 0x2d for the primary PMIC, 0x3a for the secondary PMIC,
118 * and 0x4e for the peripheral IC (where applicable).
120 static const struct {
124 { .addr = RSB_ADDR_PMIC_PRIMARY, .rta = 0x2d },
125 { .addr = RSB_ADDR_PMIC_SECONDARY, .rta = 0x3a },
126 { .addr = RSB_ADDR_PERIPH_IC, .rta = 0x4e },
127 { .addr = 0, .rta = 0 }
131 struct resource *res;
144 #define RSB_LOCK(sc) mtx_lock(&(sc)->mtx)
145 #define RSB_UNLOCK(sc) mtx_unlock(&(sc)->mtx)
146 #define RSB_ASSERT_LOCKED(sc) mtx_assert(&(sc)->mtx, MA_OWNED)
147 #define RSB_READ(sc, reg) bus_read_4((sc)->res, (reg))
148 #define RSB_WRITE(sc, reg, val) bus_write_4((sc)->res, (reg), (val))
151 rsb_get_node(device_t bus, device_t dev)
153 return (ofw_bus_get_node(bus));
157 rsb_reset(device_t dev, u_char speed, u_char addr, u_char *oldaddr)
159 struct rsb_softc *sc;
162 sc = device_get_softc(dev);
166 /* Write soft-reset bit and wait for it to self-clear. */
167 RSB_WRITE(sc, RSB_CTRL, SOFT_RESET);
168 for (retry = RSB_RESET_RETRY; retry > 0; retry--)
169 if ((RSB_READ(sc, RSB_CTRL) & SOFT_RESET) == 0)
175 device_printf(dev, "soft reset timeout\n");
179 return (IIC_ENOADDR);
183 rsb_encode(const uint8_t *buf, u_int len, u_int off)
189 for (n = off; n < MIN(len, 4 + off); n++)
190 val |= ((uint32_t)buf[n] << ((n - off) * NBBY));
196 rsb_decode(const uint32_t val, uint8_t *buf, u_int len, u_int off)
200 for (n = off; n < MIN(len, 4 + off); n++)
201 buf[n] = (val >> ((n - off) * NBBY)) & 0xff;
205 rsb_start(device_t dev)
207 struct rsb_softc *sc;
210 sc = device_get_softc(dev);
212 RSB_ASSERT_LOCKED(sc);
214 /* Start the transfer */
215 RSB_WRITE(sc, RSB_CTRL, GLOBAL_INT_ENB | START_TRANS);
217 /* Wait for transfer to complete */
219 for (retry = RSB_I2C_TIMEOUT; retry > 0; retry--) {
220 sc->status |= RSB_READ(sc, RSB_INTS);
221 if ((sc->status & INT_TRANS_OVER) != 0) {
225 DELAY((1000 * hz) / RSB_I2C_TIMEOUT);
227 if (error == 0 && (sc->status & INT_TRANS_OVER) == 0) {
228 device_printf(dev, "transfer error, status 0x%08x\n",
238 rsb_set_rta(device_t dev, uint16_t addr)
240 struct rsb_softc *sc;
244 sc = device_get_softc(dev);
246 RSB_ASSERT_LOCKED(sc);
248 /* Lookup run-time address for given device address */
249 for (rta = 0, i = 0; rsb_rtamap[i].rta != 0; i++)
250 if (rsb_rtamap[i].addr == addr) {
251 rta = rsb_rtamap[i].rta;
255 device_printf(dev, "RTA not known for address %#x\n", addr);
259 /* Set run-time address */
260 RSB_WRITE(sc, RSB_INTS, RSB_READ(sc, RSB_INTS));
261 RSB_WRITE(sc, RSB_DAR, (addr << DAR_DA_SHIFT) | (rta << DAR_RTA_SHIFT));
262 RSB_WRITE(sc, RSB_CMD, CMD_SRTA);
264 return (rsb_start(dev));
268 rsb_transfer(device_t dev, struct iic_msg *msgs, uint32_t nmsgs)
270 struct rsb_softc *sc;
271 uint32_t daddr[2], data[2], dlen;
272 uint16_t device_addr;
276 sc = device_get_softc(dev);
279 * P2WI and RSB are not really I2C or SMBus controllers, so there are
280 * some restrictions imposed by the driver.
282 * Transfers must contain exactly two messages. The first is always
283 * a write, containing a single data byte offset. Data will either
284 * be read from or written to the corresponding data byte in the
285 * second message. The slave address in both messages must be the
288 if (nmsgs != 2 || (msgs[0].flags & IIC_M_RD) == IIC_M_RD ||
289 (msgs[0].slave >> 1) != (msgs[1].slave >> 1) ||
290 msgs[0].len != 1 || msgs[1].len > RSB_MAXLEN)
293 /* The RSB controller can read or write 1, 2, or 4 bytes at a time. */
294 if (sc->type == A23_RSB) {
295 if ((msgs[1].flags & IIC_M_RD) != 0) {
296 switch (msgs[1].len) {
310 switch (msgs[1].len) {
328 mtx_sleep(sc, &sc->mtx, 0, "i2cbuswait", 0);
332 /* Select current run-time address if necessary */
333 if (sc->type == A23_RSB) {
334 device_addr = msgs[0].slave >> 1;
335 if (sc->cur_addr != device_addr) {
336 error = rsb_set_rta(dev, device_addr);
339 sc->cur_addr = device_addr;
344 /* Clear interrupt status */
345 RSB_WRITE(sc, RSB_INTS, RSB_READ(sc, RSB_INTS));
347 /* Program data access address registers */
348 daddr[0] = rsb_encode(msgs[0].buf, msgs[0].len, 0);
349 RSB_WRITE(sc, RSB_DADDR0, daddr[0]);
352 if ((msgs[1].flags & IIC_M_RD) == 0) {
353 data[0] = rsb_encode(msgs[1].buf, msgs[1].len, 0);
354 RSB_WRITE(sc, RSB_DATA0, data[0]);
357 /* Set command type for RSB */
358 if (sc->type == A23_RSB)
359 RSB_WRITE(sc, RSB_CMD, cmd);
361 /* Program data length register and transfer direction */
362 dlen = msgs[0].len - 1;
363 if ((msgs[1].flags & IIC_M_RD) == IIC_M_RD)
365 RSB_WRITE(sc, RSB_DLEN, dlen);
368 error = rsb_start(dev);
373 if ((msgs[1].flags & IIC_M_RD) == IIC_M_RD) {
374 data[0] = RSB_READ(sc, RSB_DATA0);
375 rsb_decode(data[0], msgs[1].buf, msgs[1].len, 0);
388 rsb_probe(device_t dev)
390 if (!ofw_bus_status_okay(dev))
393 switch (ofw_bus_search_compatible(dev, compat_data)->ocd_data) {
395 device_set_desc(dev, "Allwinner RSB");
398 device_set_desc(dev, "Allwinner P2WI");
404 return (BUS_PROBE_DEFAULT);
408 rsb_attach(device_t dev)
410 struct rsb_softc *sc;
413 sc = device_get_softc(dev);
414 mtx_init(&sc->mtx, device_get_nameunit(dev), "rsb", MTX_DEF);
416 sc->type = ofw_bus_search_compatible(dev, compat_data)->ocd_data;
418 if (clk_get_by_ofw_index(dev, 0, 0, &sc->clk) == 0) {
419 error = clk_enable(sc->clk);
421 device_printf(dev, "cannot enable clock\n");
425 if (hwreset_get_by_ofw_idx(dev, 0, 0, &sc->rst) == 0) {
426 error = hwreset_deassert(sc->rst);
428 device_printf(dev, "cannot de-assert reset\n");
433 if (bus_alloc_resources(dev, rsb_spec, &sc->res) != 0) {
434 device_printf(dev, "cannot allocate resources for device\n");
439 sc->iicbus = device_add_child(dev, "iicbus", -1);
440 if (sc->iicbus == NULL) {
441 device_printf(dev, "cannot add iicbus child device\n");
446 bus_generic_attach(dev);
451 bus_release_resources(dev, rsb_spec, &sc->res);
453 hwreset_release(sc->rst);
455 clk_release(sc->clk);
456 mtx_destroy(&sc->mtx);
460 static device_method_t rsb_methods[] = {
461 /* Device interface */
462 DEVMETHOD(device_probe, rsb_probe),
463 DEVMETHOD(device_attach, rsb_attach),
466 DEVMETHOD(bus_setup_intr, bus_generic_setup_intr),
467 DEVMETHOD(bus_teardown_intr, bus_generic_teardown_intr),
468 DEVMETHOD(bus_alloc_resource, bus_generic_alloc_resource),
469 DEVMETHOD(bus_release_resource, bus_generic_release_resource),
470 DEVMETHOD(bus_activate_resource, bus_generic_activate_resource),
471 DEVMETHOD(bus_deactivate_resource, bus_generic_deactivate_resource),
472 DEVMETHOD(bus_adjust_resource, bus_generic_adjust_resource),
473 DEVMETHOD(bus_set_resource, bus_generic_rl_set_resource),
474 DEVMETHOD(bus_get_resource, bus_generic_rl_get_resource),
477 DEVMETHOD(ofw_bus_get_node, rsb_get_node),
479 /* iicbus interface */
480 DEVMETHOD(iicbus_callback, iicbus_null_callback),
481 DEVMETHOD(iicbus_reset, rsb_reset),
482 DEVMETHOD(iicbus_transfer, rsb_transfer),
487 static driver_t rsb_driver = {
490 sizeof(struct rsb_softc),
493 static devclass_t rsb_devclass;
495 EARLY_DRIVER_MODULE(iicbus, rsb, iicbus_driver, iicbus_devclass, 0, 0,
496 BUS_PASS_SUPPORTDEV + BUS_PASS_ORDER_MIDDLE);
497 EARLY_DRIVER_MODULE(rsb, simplebus, rsb_driver, rsb_devclass, 0, 0,
498 BUS_PASS_SUPPORTDEV + BUS_PASS_ORDER_MIDDLE);
499 MODULE_VERSION(rsb, 1);
500 MODULE_DEPEND(rsb, iicbus, 1, 1, 1);
501 SIMPLEBUS_PNP_INFO(compat_data);