3 # On the handling of kernel options
5 # All kernel options should be listed in NOTES, with suitable
6 # descriptions. Negative options (options that make some code not
7 # compile) should be commented out; LINT (generated from NOTES) should
8 # compile as much code as possible. Try to structure option-using
9 # code so that a single option only switch code on, or only switch
10 # code off, to make it possible to have a full compile-test. If
11 # necessary, you can check for COMPILING_LINT to get maximum code
14 # All new options shall also be listed in either "conf/options" or
15 # "conf/options.<machine>". Options that affect a single source-file
16 # <xxx>.[c|s] should be directed into "opt_<xxx>.h", while options
17 # that affect multiple files should either go in "opt_global.h" if
18 # this is a kernel-wide option (used just about everywhere), or in
19 # "opt_<option-name-in-lower-case>.h" if it affects only some files.
20 # Note that the effect of listing only an option without a
21 # header-file-name in conf/options (and cousins) is that the last
22 # convention is followed.
24 # This handling scheme is not yet fully implemented.
27 # Format of this file:
28 # Option name filename
30 # If filename is missing, the default is
31 # opt_<name-of-option-in-lower-case>.h
34 AACRAID_DEBUG opt_aacraid.h
35 AHC_ALLOW_MEMIO opt_aic7xxx.h
36 AHC_TMODE_ENABLE opt_aic7xxx.h
37 AHC_DUMP_EEPROM opt_aic7xxx.h
38 AHC_DEBUG opt_aic7xxx.h
39 AHC_DEBUG_OPTS opt_aic7xxx.h
40 AHC_REG_PRETTY_PRINT opt_aic7xxx.h
41 AHD_DEBUG opt_aic79xx.h
42 AHD_DEBUG_OPTS opt_aic79xx.h
43 AHD_TMODE_ENABLE opt_aic79xx.h
44 AHD_REG_PRETTY_PRINT opt_aic79xx.h
45 ADW_ALLOW_MEMIO opt_adw.h
48 TWA_FLASH_FIRMWARE opt_twa.h
51 ALT_BREAK_TO_DEBUGGER opt_kdb.h
52 BREAK_TO_DEBUGGER opt_kdb.h
54 DDB_BUFR_SIZE opt_ddb.h
55 DDB_CAPTURE_DEFAULTBUFSIZE opt_ddb.h
56 DDB_CAPTURE_MAXBUFSIZE opt_ddb.h
62 KDB_UNATTENDED opt_kdb.h
64 SYSCTL_DEBUG opt_sysctl.h
65 EARLY_PRINTF opt_global.h
66 TEXTDUMP_PREFERRED opt_ddb.h
67 TEXTDUMP_VERBOSE opt_ddb.h
69 # Miscellaneous options.
72 ALTERA_SDCARD_FAST_SIM opt_altera_sdcard.h
73 ATSE_CFI_HACK opt_cfi.h
75 BOOTHOWTO opt_global.h
76 BOOTVERBOSE opt_global.h
78 CAPABILITIES opt_capsicum.h
79 CAPABILITY_MODE opt_capsicum.h
80 COMPAT_43 opt_compat.h
81 COMPAT_43TTY opt_compat.h
82 COMPAT_FREEBSD4 opt_compat.h
83 COMPAT_FREEBSD5 opt_compat.h
84 COMPAT_FREEBSD6 opt_compat.h
85 COMPAT_FREEBSD7 opt_compat.h
86 COMPAT_FREEBSD9 opt_compat.h
87 COMPAT_FREEBSD10 opt_compat.h
88 COMPAT_CLOUDABI64 opt_dontuse.h
89 COMPAT_LINUXKPI opt_compat.h
90 COMPILING_LINT opt_global.h
92 DEADLKRES opt_watchdog.h
93 EXT_RESOURCES opt_global.h
97 FULL_PREEMPTION opt_sched.h
99 IMAGACT_BINMISC opt_dontuse.h
100 IPI_PREEMPTION opt_sched.h
104 GEOM_CACHE opt_geom.h
105 GEOM_CONCAT opt_geom.h
109 GEOM_JOURNAL opt_geom.h
110 GEOM_LABEL opt_geom.h
111 GEOM_LABEL_GPT opt_geom.h
112 GEOM_LINUX_LVM opt_geom.h
115 GEOM_MIRROR opt_geom.h
116 GEOM_MOUNTVER opt_geom.h
117 GEOM_MULTIPATH opt_geom.h
119 GEOM_PART_APM opt_geom.h
120 GEOM_PART_BSD opt_geom.h
121 GEOM_PART_BSD64 opt_geom.h
122 GEOM_PART_EBR opt_geom.h
123 GEOM_PART_EBR_COMPAT opt_geom.h
124 GEOM_PART_GPT opt_geom.h
125 GEOM_PART_LDM opt_geom.h
126 GEOM_PART_MBR opt_geom.h
127 GEOM_PART_PC98 opt_geom.h
128 GEOM_PART_VTOC8 opt_geom.h
131 GEOM_RAID3 opt_geom.h
132 GEOM_SHSEC opt_geom.h
133 GEOM_STRIPE opt_geom.h
134 GEOM_SUNLABEL opt_geom.h
135 GEOM_UNCOMPRESS opt_geom.h
136 GEOM_UNCOMPRESS_DEBUG opt_geom.h
138 GEOM_VINUM opt_geom.h
139 GEOM_VIRSTOR opt_geom.h
142 KDTRACE_HOOKS opt_global.h
143 KDTRACE_FRAME opt_kdtrace.h
144 KN_HASHSIZE opt_kqueue.h
149 KTRACE_REQUEST_POOL opt_ktrace.h
152 MAC_BIBA opt_dontuse.h
153 MAC_BSDEXTENDED opt_dontuse.h
154 MAC_IFOFF opt_dontuse.h
155 MAC_LOMAC opt_dontuse.h
156 MAC_MLS opt_dontuse.h
157 MAC_NONE opt_dontuse.h
158 MAC_PARTITION opt_dontuse.h
159 MAC_PORTACL opt_dontuse.h
160 MAC_SEEOTHERUIDS opt_dontuse.h
162 MAC_STUB opt_dontuse.h
163 MAC_TEST opt_dontuse.h
165 MD_ROOT_FSTYPE opt_md.h
166 MD_ROOT_SIZE opt_md.h
168 MFI_DECODE_LOG opt_mfi.h
169 MPROF_BUFFERS opt_mprof.h
170 MPROF_HASH_SIZE opt_mprof.h
171 NEW_PCIB opt_global.h
172 NO_ADAPTIVE_MUTEXES opt_adaptive_mutexes.h
175 NO_EVENTTIMERS opt_timer.h
176 NO_SYSCTL_DESCR opt_global.h
177 NSWBUF_MIN opt_swap.h
178 MBUF_PACKET_ZONE_DISABLE opt_global.h
179 PANIC_REBOOT_WAIT_TIME opt_panic.h
182 PPC_PROBE_CHIPSET opt_ppc.h
184 PREEMPTION opt_sched.h
186 SCHED_4BSD opt_sched.h
187 SCHED_STATS opt_sched.h
188 SCHED_ULE opt_sched.h
190 SLHCI_DEBUG opt_slhci.h
207 SHMMAXPGS opt_sysvipc.h
211 SYSVMSG opt_sysvipc.h
212 SYSVSEM opt_sysvipc.h
213 SYSVSHM opt_sysvipc.h
214 SW_WATCHDOG opt_watchdog.h
219 WLCACHE opt_wavelan.h
220 WLDEBUG opt_wavelan.h
222 # POSIX kernel options
223 P1003_1B_MQUEUE opt_posix.h
224 P1003_1B_SEMAPHORES opt_posix.h
225 _KPOSIX_PRIORITY_SCHEDULING opt_posix.h
227 # Do we want the config file compiled into the kernel?
228 INCLUDE_CONFIG_FILE opt_config.h
230 # Options for static filesystems. These should only be used at config
231 # time, since the corresponding lkms cannot work if there are any static
232 # dependencies. Unusability is enforced by hiding the defines for the
233 # options in a never-included header.
237 FDESCFS opt_dontuse.h
240 MSDOSFS opt_dontuse.h
244 PSEUDOFS opt_dontuse.h
245 REISERFS opt_dontuse.h
249 UNIONFS opt_dontuse.h
253 PSEUDOFS_TRACE opt_pseudofs.h
256 KGSSAPI opt_kgssapi.h
257 KGSSAPI_DEBUG opt_kgssapi.h
259 # These static filesystems have one slightly bogus static dependency in
260 # sys/i386/i386/autoconf.c. If any of these filesystems are
261 # statically compiled into the kernel, code for mounting them as root
262 # filesystems will be enabled - but look below.
268 # filesystems and libiconv bridge
269 CD9660_ICONV opt_dontuse.h
270 MSDOSFS_ICONV opt_dontuse.h
271 UDF_ICONV opt_dontuse.h
273 # If you are following the conditions in the copyright,
274 # you can enable soft-updates which will speed up a lot of thigs
275 # and make the system safer from crashes at the same time.
276 # otherwise a STUB module will be compiled in.
277 SOFTUPDATES opt_ffs.h
279 # On small, embedded systems, it can be useful to turn off support for
280 # snapshots. It saves about 30-40k for a feature that would be lightly
281 # used, if it is used at all.
282 NO_FFS_SNAPSHOT opt_ffs.h
284 # Enabling this option turns on support for Access Control Lists in UFS,
285 # which can be used to support high security configurations. Depends on
289 # Enabling this option turns on support for extended attributes in UFS-based
290 # filesystems, which can be used to support high security configurations
291 # as well as new filesystem features.
292 UFS_EXTATTR opt_ufs.h
293 UFS_EXTATTR_AUTOSTART opt_ufs.h
295 # Enable fast hash lookups for large directories on UFS-based filesystems.
296 UFS_DIRHASH opt_ufs.h
298 # Enable gjournal-based UFS journal.
299 UFS_GJOURNAL opt_ufs.h
301 # The below sentence is not in English, and neither is this one.
302 # We plan to remove the static dependences above, with a
303 # <filesystem>_ROOT option to control if it usable as root. This list
304 # allows these options to be present in config files already (though
305 # they won't make any difference yet).
306 NFS_ROOT opt_nfsroot.h
311 # Options used only in subr_param.c.
316 VM_BCACHE_SIZE_MAX opt_param.h
317 VM_SWZONE_SIZE_MAX opt_param.h
323 # Generic SCSI options.
324 CAM_MAX_HIGHPOWER opt_cam.h
326 CAM_DEBUG_COMPILE opt_cam.h
327 CAM_DEBUG_DELAY opt_cam.h
328 CAM_DEBUG_BUS opt_cam.h
329 CAM_DEBUG_TARGET opt_cam.h
330 CAM_DEBUG_LUN opt_cam.h
331 CAM_DEBUG_FLAGS opt_cam.h
332 CAM_BOOT_DELAY opt_cam.h
333 SCSI_DELAY opt_scsi.h
334 SCSI_NO_SENSE_STRINGS opt_scsi.h
335 SCSI_NO_OP_STRINGS opt_scsi.h
337 # Options used only in cam/ata/ata_da.c
338 ADA_TEST_FAILURE opt_ada.h
339 ATA_STATIC_ID opt_ada.h
341 # Options used only in cam/scsi/scsi_cd.c
342 CHANGER_MIN_BUSY_SECONDS opt_cd.h
343 CHANGER_MAX_BUSY_SECONDS opt_cd.h
345 # Options used only in cam/scsi/scsi_sa.c.
346 SA_IO_TIMEOUT opt_sa.h
347 SA_SPACE_TIMEOUT opt_sa.h
348 SA_REWIND_TIMEOUT opt_sa.h
349 SA_ERASE_TIMEOUT opt_sa.h
350 SA_1FM_AT_EOD opt_sa.h
352 # Options used only in cam/scsi/scsi_pt.c
353 SCSI_PT_DEFAULT_TIMEOUT opt_pt.h
355 # Options used only in cam/scsi/scsi_ses.c
356 SES_ENABLE_PASSTHROUGH opt_ses.h
358 # Options used in dev/sym/ (Symbios SCSI driver).
359 SYM_SETUP_LP_PROBE_MAP opt_sym.h #-Low Priority Probe Map (bits)
360 # Allows the ncr to take precedence
361 # 1 (1<<0) -> 810a, 860
362 # 2 (1<<1) -> 825a, 875, 885, 895
363 # 4 (1<<2) -> 895a, 896, 1510d
364 SYM_SETUP_SCSI_DIFF opt_sym.h #-HVD support for 825a, 875, 885
365 # disabled:0 (default), enabled:1
366 SYM_SETUP_PCI_PARITY opt_sym.h #-PCI parity checking
367 # disabled:0, enabled:1 (default)
368 SYM_SETUP_MAX_LUN opt_sym.h #-Number of LUNs supported
369 # default:8, range:[1..64]
371 # Options used only in dev/ncr/*
372 SCSI_NCR_DEBUG opt_ncr.h
373 SCSI_NCR_MAX_SYNC opt_ncr.h
374 SCSI_NCR_MAX_WIDE opt_ncr.h
375 SCSI_NCR_MYADDR opt_ncr.h
377 # Options used only in dev/isp/*
378 ISP_TARGET_MODE opt_isp.h
379 ISP_FW_CRASH_DUMP opt_isp.h
380 ISP_DEFAULT_ROLES opt_isp.h
381 ISP_INTERNAL_TARGET opt_isp.h
383 # Options used only in dev/iscsi
384 ISCSI_INITIATOR_DEBUG opt_iscsi_initiator.h
393 ALTQ_CODEL opt_altq.h
394 ALTQ_DEBUG opt_altq.h
396 ALTQ_FAIRQ opt_altq.h
397 ALTQ_NOPCC opt_altq.h
402 BOOTP_BLOCKSIZE opt_bootp.h
403 BOOTP_COMPAT opt_bootp.h
404 BOOTP_NFSROOT opt_bootp.h
405 BOOTP_NFSV3 opt_bootp.h
406 BOOTP_WIRED_TO opt_bootp.h
412 IPFILTER opt_ipfilter.h
413 IPFILTER_DEFAULT_BLOCK opt_ipfilter.h
414 IPFILTER_LOG opt_ipfilter.h
415 IPFILTER_LOOKUP opt_ipfilter.h
416 IPFIREWALL opt_ipfw.h
417 IPFIREWALL_DEFAULT_TO_ACCEPT opt_ipfw.h
418 IPFIREWALL_NAT opt_ipfw.h
419 IPFIREWALL_VERBOSE opt_ipfw.h
420 IPFIREWALL_VERBOSE_LIMIT opt_ipfw.h
422 IPSEC_DEBUG opt_ipsec.h
423 IPSEC_FILTERTUNNEL opt_ipsec.h
424 IPSEC_NAT_T opt_ipsec.h
432 MROUTING opt_mrouting.h
434 PCBGROUP opt_pcbgroup.h
435 PF_DEFAULT_TO_DROP opt_pf.h
436 RADIX_MPATH opt_mpath.h
437 ROUTETABLES opt_route.h
439 SLIP_IFF_OPTS opt_slip.h
443 TCP_OFFLOAD opt_inet.h # Enable code to dispatch TCP offloading
444 TCP_RFC7413 opt_inet.h
445 TCP_RFC7413_MAX_KEYS opt_inet.h
446 TCP_SIGNATURE opt_inet.h
447 VLAN_ARRAY opt_vlan.h
449 FLOWTABLE opt_route.h
450 FLOWTABLE_HASH_ALL opt_route.h
456 SCTP_DEBUG opt_sctp.h # Enable debug printfs
457 SCTP_WITH_NO_CSUM opt_sctp.h # Use this at your peril
458 SCTP_LOCK_LOGGING opt_sctp.h # Log to KTR lock activity
459 SCTP_MBUF_LOGGING opt_sctp.h # Log to KTR general mbuf aloc/free
460 SCTP_MBCNT_LOGGING opt_sctp.h # Log to KTR mbcnt activity
461 SCTP_PACKET_LOGGING opt_sctp.h # Log to a packet buffer last N packets
462 SCTP_LTRACE_CHUNKS opt_sctp.h # Log to KTR chunks processed
463 SCTP_LTRACE_ERRORS opt_sctp.h # Log to KTR error returns.
464 SCTP_USE_PERCPU_STAT opt_sctp.h # Use per cpu stats.
465 SCTP_MCORE_INPUT opt_sctp.h # Have multiple input threads for input mbufs
466 SCTP_LOCAL_TRACE_BUF opt_sctp.h # Use tracebuffer exported via sysctl
467 SCTP_DETAILED_STR_STATS opt_sctp.h # Use per PR-SCTP policy stream stats
472 # Netgraph(4). Use option NETGRAPH to enable the base netgraph code.
473 # Each netgraph node type can be either be compiled into the kernel
474 # or loaded dynamically. To get the former, include the corresponding
475 # option below. Each type has its own man page, e.g. ng_async(4).
477 NETGRAPH_DEBUG opt_netgraph.h
478 NETGRAPH_ASYNC opt_netgraph.h
479 NETGRAPH_ATMLLC opt_netgraph.h
480 NETGRAPH_ATM_ATMPIF opt_netgraph.h
481 NETGRAPH_BLUETOOTH opt_netgraph.h
482 NETGRAPH_BLUETOOTH_BT3C opt_netgraph.h
483 NETGRAPH_BLUETOOTH_H4 opt_netgraph.h
484 NETGRAPH_BLUETOOTH_HCI opt_netgraph.h
485 NETGRAPH_BLUETOOTH_L2CAP opt_netgraph.h
486 NETGRAPH_BLUETOOTH_SOCKET opt_netgraph.h
487 NETGRAPH_BLUETOOTH_UBT opt_netgraph.h
488 NETGRAPH_BLUETOOTH_UBTBCMFW opt_netgraph.h
489 NETGRAPH_BPF opt_netgraph.h
490 NETGRAPH_BRIDGE opt_netgraph.h
491 NETGRAPH_CAR opt_netgraph.h
492 NETGRAPH_CISCO opt_netgraph.h
493 NETGRAPH_DEFLATE opt_netgraph.h
494 NETGRAPH_DEVICE opt_netgraph.h
495 NETGRAPH_ECHO opt_netgraph.h
496 NETGRAPH_EIFACE opt_netgraph.h
497 NETGRAPH_ETHER opt_netgraph.h
498 NETGRAPH_ETHER_ECHO opt_netgraph.h
499 NETGRAPH_FEC opt_netgraph.h
500 NETGRAPH_FRAME_RELAY opt_netgraph.h
501 NETGRAPH_GIF opt_netgraph.h
502 NETGRAPH_GIF_DEMUX opt_netgraph.h
503 NETGRAPH_HOLE opt_netgraph.h
504 NETGRAPH_IFACE opt_netgraph.h
505 NETGRAPH_IP_INPUT opt_netgraph.h
506 NETGRAPH_IPFW opt_netgraph.h
507 NETGRAPH_KSOCKET opt_netgraph.h
508 NETGRAPH_L2TP opt_netgraph.h
509 NETGRAPH_LMI opt_netgraph.h
510 # MPPC compression requires proprietary files (not included)
511 NETGRAPH_MPPC_COMPRESSION opt_netgraph.h
512 NETGRAPH_MPPC_ENCRYPTION opt_netgraph.h
513 NETGRAPH_NAT opt_netgraph.h
514 NETGRAPH_NETFLOW opt_netgraph.h
515 NETGRAPH_ONE2MANY opt_netgraph.h
516 NETGRAPH_PATCH opt_netgraph.h
517 NETGRAPH_PIPE opt_netgraph.h
518 NETGRAPH_PPP opt_netgraph.h
519 NETGRAPH_PPPOE opt_netgraph.h
520 NETGRAPH_PPTPGRE opt_netgraph.h
521 NETGRAPH_PRED1 opt_netgraph.h
522 NETGRAPH_RFC1490 opt_netgraph.h
523 NETGRAPH_SOCKET opt_netgraph.h
524 NETGRAPH_SPLIT opt_netgraph.h
525 NETGRAPH_SPPP opt_netgraph.h
526 NETGRAPH_TAG opt_netgraph.h
527 NETGRAPH_TCPMSS opt_netgraph.h
528 NETGRAPH_TEE opt_netgraph.h
529 NETGRAPH_TTY opt_netgraph.h
530 NETGRAPH_UI opt_netgraph.h
531 NETGRAPH_VJC opt_netgraph.h
532 NETGRAPH_VLAN opt_netgraph.h
535 NGATM_ATM opt_netgraph.h
536 NGATM_ATMBASE opt_netgraph.h
537 NGATM_SSCOP opt_netgraph.h
538 NGATM_SSCFU opt_netgraph.h
539 NGATM_UNI opt_netgraph.h
540 NGATM_CCATM opt_netgraph.h
545 TI_SF_BUF_JUMBO opt_ti.h
546 TI_JUMBO_HDRSPLIT opt_ti.h
548 # XXX Conflict: # of devices vs network protocol (Native ATM).
549 # This makes "atm.h" unusable.
552 # DPT driver debug flags
553 DPT_MEASURE_PERFORMANCE opt_dpt.h
554 DPT_RESET_HBA opt_dpt.h
556 # Misc debug flags. Most of these should probably be replaced with
557 # 'DEBUG', and then let people recompile just the interesting modules
558 # with 'make CC="cc -DDEBUG"'.
559 CLUSTERDEBUG opt_debug_cluster.h
560 DEBUG_1284 opt_ppb_1284.h
563 PLIP_DEBUG opt_plip.h
564 LOCKF_DEBUG opt_debug_lockf.h
565 SI_DEBUG opt_debug_si.h
566 IFMEDIA_DEBUG opt_ifmedia.h
570 FB_INSTALL_CDEV opt_fb.h
572 # ppbus related options
573 PERIPH_1284 opt_ppb_1284.h
574 DONTPROBE_1284 opt_ppb_1284.h
576 # smbus related options
577 ENABLE_ALART opt_intpm.h
579 # These cause changes all over the kernel
580 BLKDEV_IOSIZE opt_global.h
581 BURN_BRIDGES opt_global.h
583 DEBUG_LOCKS opt_global.h
584 DEBUG_VFS_LOCKS opt_global.h
585 DFLTPHYS opt_global.h
586 DIAGNOSTIC opt_global.h
587 INVARIANT_SUPPORT opt_global.h
588 INVARIANTS opt_global.h
590 MAXMEMDOM opt_global.h
592 MCLSHIFT opt_global.h
593 MUTEX_DEBUG opt_global.h
594 MUTEX_NOINLINE opt_global.h
595 LOCK_PROFILING opt_global.h
596 LOCK_PROFILING_FAST opt_global.h
598 REGRESSION opt_global.h
599 RWLOCK_NOINLINE opt_global.h
600 SX_NOINLINE opt_global.h
601 VFS_BIO_DEBUG opt_global.h
603 # These are VM related options
604 VM_KMEM_SIZE opt_vm.h
605 VM_KMEM_SIZE_SCALE opt_vm.h
606 VM_KMEM_SIZE_MAX opt_vm.h
607 VM_NRESERVLEVEL opt_vm.h
608 VM_LEVEL_0_ORDER opt_vm.h
610 MALLOC_MAKE_FAILURES opt_vm.h
611 MALLOC_PROFILE opt_vm.h
612 MALLOC_DEBUG_MAXZONES opt_vm.h
614 # The MemGuard replacement allocator used for tamper-after-free detection
615 DEBUG_MEMGUARD opt_vm.h
617 # The RedZone malloc(9) protection
618 DEBUG_REDZONE opt_vm.h
620 # Standard SMP options
623 # Size of the kernel message buffer
624 MSGBUF_SIZE opt_msgbuf.h
627 NFS_MINATTRTIMO opt_nfs.h
628 NFS_MAXATTRTIMO opt_nfs.h
629 NFS_MINDIRATTRTIMO opt_nfs.h
630 NFS_MAXDIRATTRTIMO opt_nfs.h
633 # For the Bt848/Bt848A/Bt849/Bt878/Bt879 driver
634 OVERRIDE_CARD opt_bktr.h
635 OVERRIDE_TUNER opt_bktr.h
636 OVERRIDE_DBX opt_bktr.h
637 OVERRIDE_MSP opt_bktr.h
638 BROOKTREE_SYSTEM_DEFAULT opt_bktr.h
639 BROOKTREE_ALLOC_PAGES opt_bktr.h
640 BKTR_OVERRIDE_CARD opt_bktr.h
641 BKTR_OVERRIDE_TUNER opt_bktr.h
642 BKTR_OVERRIDE_DBX opt_bktr.h
643 BKTR_OVERRIDE_MSP opt_bktr.h
644 BKTR_SYSTEM_DEFAULT opt_bktr.h
645 BKTR_ALLOC_PAGES opt_bktr.h
646 BKTR_USE_PLL opt_bktr.h
647 BKTR_GPIO_ACCESS opt_bktr.h
648 BKTR_NO_MSP_RESET opt_bktr.h
649 BKTR_430_FX_MODE opt_bktr.h
650 BKTR_SIS_VIA_MODE opt_bktr.h
651 BKTR_USE_FREEBSD_SMBUS opt_bktr.h
652 BKTR_NEW_MSP34XX_DRIVER opt_bktr.h
654 # Options for uart(4)
655 UART_PPS_ON_CTS opt_uart.h
656 UART_POLL_FREQ opt_uart.h
657 UART_DEV_TOLERANCE_PCT opt_uart.h
659 # options for bus/device framework
662 # options for USB support
664 USB_HOST_ALIGN opt_usb.h
665 USB_REQ_DEBUG opt_usb.h
666 USB_TEMPLATE opt_usb.h
667 USB_VERBOSE opt_usb.h
668 USB_DMA_SINGLE_ALLOC opt_usb.h
669 USB_EHCI_BIG_ENDIAN_DESC opt_usb.h
671 UKBD_DFLT_KEYMAP opt_ukbd.h
672 UPLCOM_INTR_INTERVAL opt_uplcom.h
673 UVSCOM_DEFAULT_OPKTSIZE opt_uvscom.h
674 UVSCOM_INTR_INTERVAL opt_uvscom.h
676 # Embedded system options
682 PCFCLOCK_VERBOSE opt_pcfclock.h
683 PCFCLOCK_MAX_RETRIES opt_pcfclock.h
688 KTR_CPUMASK opt_ktr.h
689 KTR_COMPILE opt_global.h
690 KTR_BOOT_ENTRIES opt_global.h
691 KTR_ENTRIES opt_global.h
692 KTR_VERBOSE opt_ktr.h
694 WITNESS_KDB opt_witness.h
695 WITNESS_NO_VNODE opt_witness.h
696 WITNESS_SKIPSPIN opt_witness.h
697 WITNESS_COUNT opt_witness.h
698 OPENSOLARIS_WITNESS opt_global.h
700 # options for ACPI support
701 ACPI_DEBUG opt_acpi.h
702 ACPI_MAX_TASKS opt_acpi.h
703 ACPI_MAX_THREADS opt_acpi.h
711 # various 'device presence' options.
715 DEV_NETMAP opt_global.h
720 DEV_RANDOM opt_global.h
721 DEV_SPLASH opt_splash.h
726 EISA_SLOTS opt_eisa.h
735 BCE_NVRAM_WRITE_SUPPORT opt_bce.h
737 SOCKBUF_DEBUG opt_global.h
740 # options for ubsec driver
741 UBSEC_DEBUG opt_ubsec.h
742 UBSEC_RNDTEST opt_ubsec.h
743 UBSEC_NO_RNG opt_ubsec.h
745 # options for hifn driver
746 HIFN_DEBUG opt_hifn.h
747 HIFN_RNDTEST opt_hifn.h
749 # options for safenet driver
750 SAFE_DEBUG opt_safe.h
751 SAFE_NO_RNG opt_safe.h
752 SAFE_RNDTEST opt_safe.h
755 MAXCONS opt_syscons.h
756 SC_ALT_MOUSE_IMAGE opt_syscons.h
757 SC_CUT_SPACES2TABS opt_syscons.h
758 SC_CUT_SEPCHARS opt_syscons.h
759 SC_DEBUG_LEVEL opt_syscons.h
760 SC_DFLT_FONT opt_syscons.h
761 SC_DISABLE_KDBKEY opt_syscons.h
762 SC_DISABLE_REBOOT opt_syscons.h
763 SC_HISTORY_SIZE opt_syscons.h
764 SC_KERNEL_CONS_ATTR opt_syscons.h
765 SC_KERNEL_CONS_REV_ATTR opt_syscons.h
766 SC_MOUSE_CHAR opt_syscons.h
767 SC_NO_CUTPASTE opt_syscons.h
768 SC_NO_FONT_LOADING opt_syscons.h
769 SC_NO_HISTORY opt_syscons.h
770 SC_NO_MODE_CHANGE opt_syscons.h
771 SC_NO_SUSPEND_VTYSWITCH opt_syscons.h
772 SC_NO_SYSMOUSE opt_syscons.h
773 SC_NORM_ATTR opt_syscons.h
774 SC_NORM_REV_ATTR opt_syscons.h
775 SC_PIXEL_MODE opt_syscons.h
776 SC_RENDER_DEBUG opt_syscons.h
777 SC_TWOBUTTON_MOUSE opt_syscons.h
778 VT_ALT_TO_ESC_HACK opt_syscons.h
779 VT_FB_DEFAULT_WIDTH opt_syscons.h
780 VT_FB_DEFAULT_HEIGHT opt_syscons.h
781 VT_MAXWINDOWS opt_syscons.h
782 VT_TWOBUTTON_MOUSE opt_syscons.h
786 # teken terminal emulator options
787 TEKEN_CONS25 opt_teken.h
788 TEKEN_UTF8 opt_teken.h
789 TERMINAL_KERN_ATTR opt_teken.h
790 TERMINAL_NORM_ATTR opt_teken.h
793 PRINTF_BUFR_SIZE opt_printf.h
796 KBD_DISABLE_KEYMAP_LOAD opt_kbd.h
797 KBD_INSTALL_CDEV opt_kbd.h
798 KBD_MAXRETRY opt_kbd.h
799 KBD_MAXWAIT opt_kbd.h
800 KBD_RESETDELAY opt_kbd.h
801 KBDIO_DEBUG opt_kbd.h
803 # options for the Atheros driver
807 ATH_DIAGAPI opt_ath.h
808 ATH_TX99_DIAG opt_ath.h
809 ATH_ENABLE_11N opt_ath.h
810 ATH_ENABLE_DFS opt_ath.h
811 ATH_EEPROM_FIRMWARE opt_ath.h
812 ATH_ENABLE_RADIOTAP_VENDOR_EXT opt_ath.h
813 ATH_DEBUG_ALQ opt_ath.h
814 ATH_KTR_INTR_DEBUG opt_ath.h
816 # options for the Atheros hal
817 AH_SUPPORT_AR5416 opt_ah.h
818 # XXX For now, this breaks non-AR9130 chipsets, so only use it
819 # XXX when actually targetting AR9130.
820 AH_SUPPORT_AR9130 opt_ah.h
822 # This is required for AR933x SoC support
823 AH_SUPPORT_AR9330 opt_ah.h
824 AH_SUPPORT_AR9340 opt_ah.h
825 AH_SUPPORT_QCA9530 opt_ah.h
826 AH_SUPPORT_QCA9550 opt_ah.h
830 AH_DEBUG_ALQ opt_ah.h
831 AH_REGOPS_FUNC opt_ah.h
832 AH_WRITE_REGDOMAIN opt_ah.h
833 AH_DEBUG_COUNTRY opt_ah.h
834 AH_WRITE_EEPROM opt_ah.h
835 AH_PRIVATE_DIAG opt_ah.h
836 AH_NEED_DESC_SWAP opt_ah.h
837 AH_USE_INIPDGAIN opt_ah.h
839 AH_RXCFG_SDMAMW_4BYTES opt_ah.h
840 AH_INTERRUPT_DEBUGGING opt_ah.h
841 # AR5416 and later interrupt mitigation
842 # XXX do not use this for AR9130
843 AH_AR5416_INTERRUPT_MITIGATION opt_ah.h
845 # options for the Broadcom BCM43xx driver (bwi)
847 BWI_DEBUG_VERBOSE opt_bwi.h
849 # options for the Marvell 8335 wireless driver
850 MALO_DEBUG opt_malo.h
851 MALO_TXBUF opt_malo.h
852 MALO_RXBUF opt_malo.h
854 # options for the Marvell wireless driver
858 MWL_DIAGAPI opt_mwl.h
859 MWL_AGGR_SIZE opt_mwl.h
860 MWL_TX_NODROP opt_mwl.h
862 # Options for the Intel 802.11ac wireless driver
865 # Options for the Intel 802.11n wireless driver
868 # Options for the Intel 3945ABG wireless driver
872 DCONS_BUF_SIZE opt_dcons.h
873 DCONS_POLL_HZ opt_dcons.h
874 DCONS_FORCE_CONSOLE opt_dcons.h
875 DCONS_FORCE_GDB opt_dcons.h
878 HWPMC_DEBUG opt_global.h
880 HWPMC_MIPS_BACKTRACE opt_hwpmc_hooks.h
882 # XBOX options for FreeBSD/i386, but some files are MI
885 # Interrupt filtering
888 # 802.11 support layer
889 IEEE80211_DEBUG opt_wlan.h
890 IEEE80211_DEBUG_REFCNT opt_wlan.h
891 IEEE80211_AMPDU_AGE opt_wlan.h
892 IEEE80211_SUPPORT_MESH opt_wlan.h
893 IEEE80211_SUPPORT_SUPERG opt_wlan.h
894 IEEE80211_SUPPORT_TDMA opt_wlan.h
895 IEEE80211_ALQ opt_wlan.h
896 IEEE80211_DFS_DEBUG opt_wlan.h
898 # 802.11 TDMA support
899 TDMA_SLOTLEN_DEFAULT opt_tdma.h
900 TDMA_SLOTCNT_DEFAULT opt_tdma.h
901 TDMA_BINTVAL_DEFAULT opt_tdma.h
902 TDMA_TXRATE_11B_DEFAULT opt_tdma.h
903 TDMA_TXRATE_11G_DEFAULT opt_tdma.h
904 TDMA_TXRATE_11A_DEFAULT opt_tdma.h
905 TDMA_TXRATE_TURBO_DEFAULT opt_tdma.h
906 TDMA_TXRATE_HALF_DEFAULT opt_tdma.h
907 TDMA_TXRATE_QUARTER_DEFAULT opt_tdma.h
908 TDMA_TXRATE_11NA_DEFAULT opt_tdma.h
909 TDMA_TXRATE_11NG_DEFAULT opt_tdma.h
912 PICKMODE_DEBUG opt_videomode.h
914 # Network stack virtualization options
916 VNET_DEBUG opt_global.h
918 # Common Flash Interface (CFI) options
919 CFI_SUPPORT_STRATAFLASH opt_cfi.h
920 CFI_ARMEDANDDANGEROUS opt_cfi.h
921 CFI_HARDWAREBYTESWAP opt_cfi.h
925 SND_DIAGNOSTIC opt_snd.h
926 SND_FEEDER_MULTIFORMAT opt_snd.h
927 SND_FEEDER_FULL_MULTIFORMAT opt_snd.h
928 SND_FEEDER_RATE_HP opt_snd.h
930 SND_OLDSTEREO opt_snd.h
934 # Flattened device tree options
936 FDT_DTB_STATIC opt_platform.h
938 # OFED Infiniband stack
940 OFED_DEBUG_INIT opt_ofed.h
944 IPOIB_DEBUG opt_ofed.h
947 # Resource Accounting
949 RACCT_DEFAULT_TO_DISABLED opt_global.h
954 # Random number generator(s)
955 # Which CSPRNG hash we get.
956 # If Yarrow is not chosen, Fortuna is selected.
957 RANDOM_YARROW opt_global.h
958 # With this, no entropy processor is loaded, but the entropy
959 # harvesting infrastructure is present. This means an entropy
960 # processor may be loaded as a module.
961 RANDOM_LOADABLE opt_global.h
962 # This turns on high-rate and potentially expensive harvesting in
963 # the uma slab allocator.
964 RANDOM_ENABLE_UMA opt_global.h
967 EM_MULTIQUEUE opt_em.h