3 # On the handling of kernel options
5 # All kernel options should be listed in NOTES, with suitable
6 # descriptions. Negative options (options that make some code not
7 # compile) should be commented out; LINT (generated from NOTES) should
8 # compile as much code as possible. Try to structure option-using
9 # code so that a single option only switch code on, or only switch
10 # code off, to make it possible to have a full compile-test. If
11 # necessary, you can check for COMPILING_LINT to get maximum code
14 # All new options shall also be listed in either "conf/options" or
15 # "conf/options.<machine>". Options that affect a single source-file
16 # <xxx>.[c|s] should be directed into "opt_<xxx>.h", while options
17 # that affect multiple files should either go in "opt_global.h" if
18 # this is a kernel-wide option (used just about everywhere), or in
19 # "opt_<option-name-in-lower-case>.h" if it affects only some files.
20 # Note that the effect of listing only an option without a
21 # header-file-name in conf/options (and cousins) is that the last
22 # convention is followed.
24 # This handling scheme is not yet fully implemented.
27 # Format of this file:
28 # Option name filename
30 # If filename is missing, the default is
31 # opt_<name-of-option-in-lower-case>.h
34 AACRAID_DEBUG opt_aacraid.h
35 AHC_ALLOW_MEMIO opt_aic7xxx.h
36 AHC_TMODE_ENABLE opt_aic7xxx.h
37 AHC_DUMP_EEPROM opt_aic7xxx.h
38 AHC_DEBUG opt_aic7xxx.h
39 AHC_DEBUG_OPTS opt_aic7xxx.h
40 AHC_REG_PRETTY_PRINT opt_aic7xxx.h
41 AHD_DEBUG opt_aic79xx.h
42 AHD_DEBUG_OPTS opt_aic79xx.h
43 AHD_TMODE_ENABLE opt_aic79xx.h
44 AHD_REG_PRETTY_PRINT opt_aic79xx.h
45 ADW_ALLOW_MEMIO opt_adw.h
48 TWA_FLASH_FIRMWARE opt_twa.h
51 ALT_BREAK_TO_DEBUGGER opt_kdb.h
52 BREAK_TO_DEBUGGER opt_kdb.h
53 BUF_TRACKING opt_global.h
55 DDB_BUFR_SIZE opt_ddb.h
56 DDB_CAPTURE_DEFAULTBUFSIZE opt_ddb.h
57 DDB_CAPTURE_MAXBUFSIZE opt_ddb.h
60 FULL_BUF_TRACKING opt_global.h
64 KDB_UNATTENDED opt_kdb.h
66 SYSCTL_DEBUG opt_sysctl.h
67 EARLY_PRINTF opt_global.h
68 TEXTDUMP_PREFERRED opt_ddb.h
69 TEXTDUMP_VERBOSE opt_ddb.h
70 NUM_CORE_FILES opt_global.h
72 # Miscellaneous options.
75 ALTERA_SDCARD_FAST_SIM opt_altera_sdcard.h
76 ATSE_CFI_HACK opt_cfi.h
78 BOOTHOWTO opt_global.h
79 BOOTVERBOSE opt_global.h
81 CAPABILITIES opt_capsicum.h
82 CAPABILITY_MODE opt_capsicum.h
83 COMPAT_43 opt_compat.h
84 COMPAT_43TTY opt_compat.h
85 COMPAT_FREEBSD4 opt_compat.h
86 COMPAT_FREEBSD5 opt_compat.h
87 COMPAT_FREEBSD6 opt_compat.h
88 COMPAT_FREEBSD7 opt_compat.h
89 COMPAT_FREEBSD9 opt_compat.h
90 COMPAT_FREEBSD10 opt_compat.h
91 COMPAT_FREEBSD11 opt_compat.h
92 COMPAT_CLOUDABI32 opt_dontuse.h
93 COMPAT_CLOUDABI64 opt_dontuse.h
94 COMPAT_LINUXKPI opt_compat.h
95 COMPILING_LINT opt_global.h
97 DEADLKRES opt_watchdog.h
99 EXT_RESOURCES opt_global.h
101 FILEMON opt_dontuse.h
103 FULL_PREEMPTION opt_sched.h
105 IMAGACT_BINMISC opt_dontuse.h
106 IPI_PREEMPTION opt_sched.h
110 GEOM_CACHE opt_geom.h
111 GEOM_CONCAT opt_geom.h
115 GEOM_JOURNAL opt_geom.h
116 GEOM_LABEL opt_geom.h
117 GEOM_LABEL_GPT opt_geom.h
118 GEOM_LINUX_LVM opt_geom.h
121 GEOM_MIRROR opt_geom.h
122 GEOM_MOUNTVER opt_geom.h
123 GEOM_MULTIPATH opt_geom.h
125 GEOM_PART_APM opt_geom.h
126 GEOM_PART_BSD opt_geom.h
127 GEOM_PART_BSD64 opt_geom.h
128 GEOM_PART_EBR opt_geom.h
129 GEOM_PART_EBR_COMPAT opt_geom.h
130 GEOM_PART_GPT opt_geom.h
131 GEOM_PART_LDM opt_geom.h
132 GEOM_PART_MBR opt_geom.h
133 GEOM_PART_VTOC8 opt_geom.h
135 GEOM_RAID3 opt_geom.h
136 GEOM_SHSEC opt_geom.h
137 GEOM_STRIPE opt_geom.h
138 GEOM_SUNLABEL opt_geom.h
140 GEOM_UZIP_DEBUG opt_geom.h
141 GEOM_VINUM opt_geom.h
142 GEOM_VIRSTOR opt_geom.h
146 KDTRACE_HOOKS opt_global.h
147 KDTRACE_FRAME opt_kdtrace.h
148 KN_HASHSIZE opt_kqueue.h
153 KTRACE_REQUEST_POOL opt_ktrace.h
156 MAC_BIBA opt_dontuse.h
157 MAC_BSDEXTENDED opt_dontuse.h
158 MAC_IFOFF opt_dontuse.h
159 MAC_LOMAC opt_dontuse.h
160 MAC_MLS opt_dontuse.h
161 MAC_NONE opt_dontuse.h
162 MAC_PARTITION opt_dontuse.h
163 MAC_PORTACL opt_dontuse.h
164 MAC_SEEOTHERUIDS opt_dontuse.h
166 MAC_STUB opt_dontuse.h
167 MAC_TEST opt_dontuse.h
169 MD_ROOT_FSTYPE opt_md.h
170 MD_ROOT_SIZE opt_md.h
172 MFI_DECODE_LOG opt_mfi.h
173 MPROF_BUFFERS opt_mprof.h
174 MPROF_HASH_SIZE opt_mprof.h
175 NEW_PCIB opt_global.h
176 NO_ADAPTIVE_MUTEXES opt_adaptive_mutexes.h
179 NO_EVENTTIMERS opt_timer.h
180 NO_SYSCTL_DESCR opt_global.h
181 NSWBUF_MIN opt_swap.h
182 MBUF_PACKET_ZONE_DISABLE opt_global.h
183 PANIC_REBOOT_WAIT_TIME opt_panic.h
187 PPC_PROBE_CHIPSET opt_ppc.h
189 PREEMPTION opt_sched.h
191 SCHED_4BSD opt_sched.h
192 SCHED_STATS opt_sched.h
193 SCHED_ULE opt_sched.h
195 SLHCI_DEBUG opt_slhci.h
212 SHMMAXPGS opt_sysvipc.h
216 SYSVMSG opt_sysvipc.h
217 SYSVSEM opt_sysvipc.h
218 SYSVSHM opt_sysvipc.h
219 SW_WATCHDOG opt_watchdog.h
222 UMTX_CHAINS opt_global.h
225 # POSIX kernel options
226 P1003_1B_MQUEUE opt_posix.h
227 P1003_1B_SEMAPHORES opt_posix.h
228 _KPOSIX_PRIORITY_SCHEDULING opt_posix.h
230 # Do we want the config file compiled into the kernel?
231 INCLUDE_CONFIG_FILE opt_config.h
233 # Options for static filesystems. These should only be used at config
234 # time, since the corresponding lkms cannot work if there are any static
235 # dependencies. Unusability is enforced by hiding the defines for the
236 # options in a never-included header.
240 FDESCFS opt_dontuse.h
243 MSDOSFS opt_dontuse.h
247 PSEUDOFS opt_dontuse.h
251 UNIONFS opt_dontuse.h
255 PSEUDOFS_TRACE opt_pseudofs.h
258 KGSSAPI opt_kgssapi.h
259 KGSSAPI_DEBUG opt_kgssapi.h
261 # These static filesystems have one slightly bogus static dependency in
262 # sys/i386/i386/autoconf.c. If any of these filesystems are
263 # statically compiled into the kernel, code for mounting them as root
264 # filesystems will be enabled - but look below.
270 # filesystems and libiconv bridge
271 CD9660_ICONV opt_dontuse.h
272 MSDOSFS_ICONV opt_dontuse.h
273 UDF_ICONV opt_dontuse.h
275 # If you are following the conditions in the copyright,
276 # you can enable soft-updates which will speed up a lot of thigs
277 # and make the system safer from crashes at the same time.
278 # otherwise a STUB module will be compiled in.
279 SOFTUPDATES opt_ffs.h
281 # On small, embedded systems, it can be useful to turn off support for
282 # snapshots. It saves about 30-40k for a feature that would be lightly
283 # used, if it is used at all.
284 NO_FFS_SNAPSHOT opt_ffs.h
286 # Enabling this option turns on support for Access Control Lists in UFS,
287 # which can be used to support high security configurations. Depends on
291 # Enabling this option turns on support for extended attributes in UFS-based
292 # filesystems, which can be used to support high security configurations
293 # as well as new filesystem features.
294 UFS_EXTATTR opt_ufs.h
295 UFS_EXTATTR_AUTOSTART opt_ufs.h
297 # Enable fast hash lookups for large directories on UFS-based filesystems.
298 UFS_DIRHASH opt_ufs.h
300 # Enable gjournal-based UFS journal.
301 UFS_GJOURNAL opt_ufs.h
303 # The below sentence is not in English, and neither is this one.
304 # We plan to remove the static dependences above, with a
305 # <filesystem>_ROOT option to control if it usable as root. This list
306 # allows these options to be present in config files already (though
307 # they won't make any difference yet).
308 NFS_ROOT opt_nfsroot.h
313 # Options used only in subr_param.c.
318 VM_BCACHE_SIZE_MAX opt_param.h
319 VM_SWZONE_SIZE_MAX opt_param.h
325 # Generic SCSI options.
326 CAM_MAX_HIGHPOWER opt_cam.h
328 CAM_DEBUG_COMPILE opt_cam.h
329 CAM_DEBUG_DELAY opt_cam.h
330 CAM_DEBUG_BUS opt_cam.h
331 CAM_DEBUG_TARGET opt_cam.h
332 CAM_DEBUG_LUN opt_cam.h
333 CAM_DEBUG_FLAGS opt_cam.h
334 CAM_BOOT_DELAY opt_cam.h
335 CAM_IOSCHED_DYNAMIC opt_cam.h
336 SCSI_DELAY opt_scsi.h
337 SCSI_NO_SENSE_STRINGS opt_scsi.h
338 SCSI_NO_OP_STRINGS opt_scsi.h
340 # Options used only in cam/ata/ata_da.c
341 ADA_TEST_FAILURE opt_ada.h
342 ATA_STATIC_ID opt_ada.h
344 # Options used only in cam/scsi/scsi_cd.c
345 CHANGER_MIN_BUSY_SECONDS opt_cd.h
346 CHANGER_MAX_BUSY_SECONDS opt_cd.h
348 # Options used only in cam/scsi/scsi_sa.c.
349 SA_IO_TIMEOUT opt_sa.h
350 SA_SPACE_TIMEOUT opt_sa.h
351 SA_REWIND_TIMEOUT opt_sa.h
352 SA_ERASE_TIMEOUT opt_sa.h
353 SA_1FM_AT_EOD opt_sa.h
355 # Options used only in cam/scsi/scsi_pt.c
356 SCSI_PT_DEFAULT_TIMEOUT opt_pt.h
358 # Options used only in cam/scsi/scsi_ses.c
359 SES_ENABLE_PASSTHROUGH opt_ses.h
361 # Options used in dev/sym/ (Symbios SCSI driver).
362 SYM_SETUP_LP_PROBE_MAP opt_sym.h #-Low Priority Probe Map (bits)
363 # Allows the ncr to take precedence
364 # 1 (1<<0) -> 810a, 860
365 # 2 (1<<1) -> 825a, 875, 885, 895
366 # 4 (1<<2) -> 895a, 896, 1510d
367 SYM_SETUP_SCSI_DIFF opt_sym.h #-HVD support for 825a, 875, 885
368 # disabled:0 (default), enabled:1
369 SYM_SETUP_PCI_PARITY opt_sym.h #-PCI parity checking
370 # disabled:0, enabled:1 (default)
371 SYM_SETUP_MAX_LUN opt_sym.h #-Number of LUNs supported
372 # default:8, range:[1..64]
374 # Options used only in dev/ncr/*
375 SCSI_NCR_DEBUG opt_ncr.h
376 SCSI_NCR_MAX_SYNC opt_ncr.h
377 SCSI_NCR_MAX_WIDE opt_ncr.h
378 SCSI_NCR_MYADDR opt_ncr.h
380 # Options used only in dev/isp/*
381 ISP_TARGET_MODE opt_isp.h
382 ISP_FW_CRASH_DUMP opt_isp.h
383 ISP_DEFAULT_ROLES opt_isp.h
384 ISP_INTERNAL_TARGET opt_isp.h
385 ISP_FCTAPE_OFF opt_isp.h
387 # Options used only in dev/iscsi
388 ISCSI_INITIATOR_DEBUG opt_iscsi_initiator.h
397 ALTQ_CODEL opt_altq.h
398 ALTQ_DEBUG opt_altq.h
400 ALTQ_FAIRQ opt_altq.h
401 ALTQ_NOPCC opt_altq.h
406 BOOTP_BLOCKSIZE opt_bootp.h
407 BOOTP_COMPAT opt_bootp.h
408 BOOTP_NFSROOT opt_bootp.h
409 BOOTP_NFSV3 opt_bootp.h
410 BOOTP_WIRED_TO opt_bootp.h
413 RATELIMIT opt_ratelimit.h
417 IPFILTER opt_ipfilter.h
418 IPFILTER_DEFAULT_BLOCK opt_ipfilter.h
419 IPFILTER_LOG opt_ipfilter.h
420 IPFILTER_LOOKUP opt_ipfilter.h
421 IPFIREWALL opt_ipfw.h
422 IPFIREWALL_DEFAULT_TO_ACCEPT opt_ipfw.h
423 IPFIREWALL_NAT opt_ipfw.h
424 IPFIREWALL_NAT64 opt_ipfw.h
425 IPFIREWALL_NAT64_DIRECT_OUTPUT opt_ipfw.h
426 IPFIREWALL_NPTV6 opt_ipfw.h
427 IPFIREWALL_VERBOSE opt_ipfw.h
428 IPFIREWALL_VERBOSE_LIMIT opt_ipfw.h
429 IPFIREWALL_PMOD opt_ipfw.h
431 IPSEC_DEBUG opt_ipsec.h
432 IPSEC_SUPPORT opt_ipsec.h
440 MROUTING opt_mrouting.h
442 PCBGROUP opt_pcbgroup.h
443 PF_DEFAULT_TO_DROP opt_pf.h
444 RADIX_MPATH opt_mpath.h
445 ROUTETABLES opt_route.h
447 SLIP_IFF_OPTS opt_slip.h
452 TCP_OFFLOAD opt_inet.h # Enable code to dispatch TCP offloading
453 TCP_RFC7413 opt_inet.h
454 TCP_RFC7413_MAX_KEYS opt_inet.h
455 TCP_SIGNATURE opt_ipsec.h
456 VLAN_ARRAY opt_vlan.h
458 FLOWTABLE opt_route.h
459 FLOWTABLE_HASH_ALL opt_route.h
465 SCTP_DEBUG opt_sctp.h # Enable debug printfs
466 SCTP_WITH_NO_CSUM opt_sctp.h # Use this at your peril
467 SCTP_LOCK_LOGGING opt_sctp.h # Log to KTR lock activity
468 SCTP_MBUF_LOGGING opt_sctp.h # Log to KTR general mbuf aloc/free
469 SCTP_MBCNT_LOGGING opt_sctp.h # Log to KTR mbcnt activity
470 SCTP_PACKET_LOGGING opt_sctp.h # Log to a packet buffer last N packets
471 SCTP_LTRACE_CHUNKS opt_sctp.h # Log to KTR chunks processed
472 SCTP_LTRACE_ERRORS opt_sctp.h # Log to KTR error returns.
473 SCTP_USE_PERCPU_STAT opt_sctp.h # Use per cpu stats.
474 SCTP_MCORE_INPUT opt_sctp.h # Have multiple input threads for input mbufs
475 SCTP_LOCAL_TRACE_BUF opt_sctp.h # Use tracebuffer exported via sysctl
476 SCTP_DETAILED_STR_STATS opt_sctp.h # Use per PR-SCTP policy stream stats
481 # Netgraph(4). Use option NETGRAPH to enable the base netgraph code.
482 # Each netgraph node type can be either be compiled into the kernel
483 # or loaded dynamically. To get the former, include the corresponding
484 # option below. Each type has its own man page, e.g. ng_async(4).
486 NETGRAPH_DEBUG opt_netgraph.h
487 NETGRAPH_ASYNC opt_netgraph.h
488 NETGRAPH_ATMLLC opt_netgraph.h
489 NETGRAPH_ATM_ATMPIF opt_netgraph.h
490 NETGRAPH_BLUETOOTH opt_netgraph.h
491 NETGRAPH_BLUETOOTH_BT3C opt_netgraph.h
492 NETGRAPH_BLUETOOTH_H4 opt_netgraph.h
493 NETGRAPH_BLUETOOTH_HCI opt_netgraph.h
494 NETGRAPH_BLUETOOTH_L2CAP opt_netgraph.h
495 NETGRAPH_BLUETOOTH_SOCKET opt_netgraph.h
496 NETGRAPH_BLUETOOTH_UBT opt_netgraph.h
497 NETGRAPH_BLUETOOTH_UBTBCMFW opt_netgraph.h
498 NETGRAPH_BPF opt_netgraph.h
499 NETGRAPH_BRIDGE opt_netgraph.h
500 NETGRAPH_CAR opt_netgraph.h
501 NETGRAPH_CISCO opt_netgraph.h
502 NETGRAPH_DEFLATE opt_netgraph.h
503 NETGRAPH_DEVICE opt_netgraph.h
504 NETGRAPH_ECHO opt_netgraph.h
505 NETGRAPH_EIFACE opt_netgraph.h
506 NETGRAPH_ETHER opt_netgraph.h
507 NETGRAPH_ETHER_ECHO opt_netgraph.h
508 NETGRAPH_FEC opt_netgraph.h
509 NETGRAPH_FRAME_RELAY opt_netgraph.h
510 NETGRAPH_GIF opt_netgraph.h
511 NETGRAPH_GIF_DEMUX opt_netgraph.h
512 NETGRAPH_HOLE opt_netgraph.h
513 NETGRAPH_IFACE opt_netgraph.h
514 NETGRAPH_IP_INPUT opt_netgraph.h
515 NETGRAPH_IPFW opt_netgraph.h
516 NETGRAPH_KSOCKET opt_netgraph.h
517 NETGRAPH_L2TP opt_netgraph.h
518 NETGRAPH_LMI opt_netgraph.h
519 NETGRAPH_MPPC_COMPRESSION opt_netgraph.h
520 NETGRAPH_MPPC_ENCRYPTION opt_netgraph.h
521 NETGRAPH_NAT opt_netgraph.h
522 NETGRAPH_NETFLOW opt_netgraph.h
523 NETGRAPH_ONE2MANY opt_netgraph.h
524 NETGRAPH_PATCH opt_netgraph.h
525 NETGRAPH_PIPE opt_netgraph.h
526 NETGRAPH_PPP opt_netgraph.h
527 NETGRAPH_PPPOE opt_netgraph.h
528 NETGRAPH_PPTPGRE opt_netgraph.h
529 NETGRAPH_PRED1 opt_netgraph.h
530 NETGRAPH_RFC1490 opt_netgraph.h
531 NETGRAPH_SOCKET opt_netgraph.h
532 NETGRAPH_SPLIT opt_netgraph.h
533 NETGRAPH_SPPP opt_netgraph.h
534 NETGRAPH_TAG opt_netgraph.h
535 NETGRAPH_TCPMSS opt_netgraph.h
536 NETGRAPH_TEE opt_netgraph.h
537 NETGRAPH_TTY opt_netgraph.h
538 NETGRAPH_UI opt_netgraph.h
539 NETGRAPH_VJC opt_netgraph.h
540 NETGRAPH_VLAN opt_netgraph.h
543 NGATM_ATM opt_netgraph.h
544 NGATM_ATMBASE opt_netgraph.h
545 NGATM_SSCOP opt_netgraph.h
546 NGATM_SSCFU opt_netgraph.h
547 NGATM_UNI opt_netgraph.h
548 NGATM_CCATM opt_netgraph.h
553 TI_SF_BUF_JUMBO opt_ti.h
554 TI_JUMBO_HDRSPLIT opt_ti.h
556 # DPT driver debug flags
557 DPT_MEASURE_PERFORMANCE opt_dpt.h
558 DPT_RESET_HBA opt_dpt.h
560 # Misc debug flags. Most of these should probably be replaced with
561 # 'DEBUG', and then let people recompile just the interesting modules
562 # with 'make CC="cc -DDEBUG"'.
563 CLUSTERDEBUG opt_debug_cluster.h
564 DEBUG_1284 opt_ppb_1284.h
567 PLIP_DEBUG opt_plip.h
568 LOCKF_DEBUG opt_debug_lockf.h
569 SI_DEBUG opt_debug_si.h
570 IFMEDIA_DEBUG opt_ifmedia.h
574 FB_INSTALL_CDEV opt_fb.h
576 # ppbus related options
577 PERIPH_1284 opt_ppb_1284.h
578 DONTPROBE_1284 opt_ppb_1284.h
580 # smbus related options
581 ENABLE_ALART opt_intpm.h
583 # These cause changes all over the kernel
584 BLKDEV_IOSIZE opt_global.h
585 BURN_BRIDGES opt_global.h
587 DEBUG_LOCKS opt_global.h
588 DEBUG_VFS_LOCKS opt_global.h
589 DFLTPHYS opt_global.h
590 DIAGNOSTIC opt_global.h
591 INVARIANT_SUPPORT opt_global.h
592 INVARIANTS opt_global.h
594 MAXMEMDOM opt_global.h
596 MCLSHIFT opt_global.h
597 MUTEX_NOINLINE opt_global.h
598 LOCK_PROFILING opt_global.h
599 LOCK_PROFILING_FAST opt_global.h
601 REGRESSION opt_global.h
602 RWLOCK_NOINLINE opt_global.h
603 SX_NOINLINE opt_global.h
604 VFS_BIO_DEBUG opt_global.h
606 # These are VM related options
607 VM_KMEM_SIZE opt_vm.h
608 VM_KMEM_SIZE_SCALE opt_vm.h
609 VM_KMEM_SIZE_MAX opt_vm.h
610 VM_NRESERVLEVEL opt_vm.h
611 VM_NUMA_ALLOC opt_vm.h
612 VM_LEVEL_0_ORDER opt_vm.h
614 MALLOC_MAKE_FAILURES opt_vm.h
615 MALLOC_PROFILE opt_vm.h
616 MALLOC_DEBUG_MAXZONES opt_vm.h
618 # The MemGuard replacement allocator used for tamper-after-free detection
619 DEBUG_MEMGUARD opt_vm.h
621 # The RedZone malloc(9) protection
622 DEBUG_REDZONE opt_vm.h
624 # Standard SMP options
625 EARLY_AP_STARTUP opt_global.h
628 # Size of the kernel message buffer
629 MSGBUF_SIZE opt_msgbuf.h
632 NFS_MINATTRTIMO opt_nfs.h
633 NFS_MAXATTRTIMO opt_nfs.h
634 NFS_MINDIRATTRTIMO opt_nfs.h
635 NFS_MAXDIRATTRTIMO opt_nfs.h
638 # For the Bt848/Bt848A/Bt849/Bt878/Bt879 driver
639 OVERRIDE_CARD opt_bktr.h
640 OVERRIDE_TUNER opt_bktr.h
641 OVERRIDE_DBX opt_bktr.h
642 OVERRIDE_MSP opt_bktr.h
643 BROOKTREE_SYSTEM_DEFAULT opt_bktr.h
644 BROOKTREE_ALLOC_PAGES opt_bktr.h
645 BKTR_OVERRIDE_CARD opt_bktr.h
646 BKTR_OVERRIDE_TUNER opt_bktr.h
647 BKTR_OVERRIDE_DBX opt_bktr.h
648 BKTR_OVERRIDE_MSP opt_bktr.h
649 BKTR_SYSTEM_DEFAULT opt_bktr.h
650 BKTR_ALLOC_PAGES opt_bktr.h
651 BKTR_USE_PLL opt_bktr.h
652 BKTR_GPIO_ACCESS opt_bktr.h
653 BKTR_NO_MSP_RESET opt_bktr.h
654 BKTR_430_FX_MODE opt_bktr.h
655 BKTR_SIS_VIA_MODE opt_bktr.h
656 BKTR_USE_FREEBSD_SMBUS opt_bktr.h
657 BKTR_NEW_MSP34XX_DRIVER opt_bktr.h
659 # Options for uart(4)
660 UART_PPS_ON_CTS opt_uart.h
661 UART_POLL_FREQ opt_uart.h
662 UART_DEV_TOLERANCE_PCT opt_uart.h
664 # options for bus/device framework
667 # options for USB support
669 USB_HOST_ALIGN opt_usb.h
670 USB_REQ_DEBUG opt_usb.h
671 USB_TEMPLATE opt_usb.h
672 USB_VERBOSE opt_usb.h
673 USB_DMA_SINGLE_ALLOC opt_usb.h
674 USB_EHCI_BIG_ENDIAN_DESC opt_usb.h
676 UKBD_DFLT_KEYMAP opt_ukbd.h
677 UPLCOM_INTR_INTERVAL opt_uplcom.h
678 UVSCOM_DEFAULT_OPKTSIZE opt_uvscom.h
679 UVSCOM_INTR_INTERVAL opt_uvscom.h
681 # options for the Realtek rtwn driver
682 RTWN_DEBUG opt_rtwn.h
683 RTWN_WITHOUT_UCODE opt_rtwn.h
685 # Embedded system options
691 PCFCLOCK_VERBOSE opt_pcfclock.h
692 PCFCLOCK_MAX_RETRIES opt_pcfclock.h
697 KTR_CPUMASK opt_ktr.h
698 KTR_COMPILE opt_global.h
699 KTR_BOOT_ENTRIES opt_global.h
700 KTR_ENTRIES opt_global.h
701 KTR_VERBOSE opt_ktr.h
703 WITNESS_KDB opt_witness.h
704 WITNESS_NO_VNODE opt_witness.h
705 WITNESS_SKIPSPIN opt_witness.h
706 WITNESS_COUNT opt_witness.h
707 OPENSOLARIS_WITNESS opt_global.h
709 # options for ACPI support
710 ACPI_DEBUG opt_acpi.h
711 ACPI_MAX_TASKS opt_acpi.h
712 ACPI_MAX_THREADS opt_acpi.h
720 # various 'device presence' options.
723 DEV_NETMAP opt_global.h
728 DEV_RANDOM opt_global.h
729 DEV_SPLASH opt_splash.h
739 BCE_NVRAM_WRITE_SUPPORT opt_bce.h
741 SOCKBUF_DEBUG opt_global.h
744 # options for ubsec driver
745 UBSEC_DEBUG opt_ubsec.h
746 UBSEC_RNDTEST opt_ubsec.h
747 UBSEC_NO_RNG opt_ubsec.h
749 # options for hifn driver
750 HIFN_DEBUG opt_hifn.h
751 HIFN_RNDTEST opt_hifn.h
753 # options for safenet driver
754 SAFE_DEBUG opt_safe.h
755 SAFE_NO_RNG opt_safe.h
756 SAFE_RNDTEST opt_safe.h
759 MAXCONS opt_syscons.h
760 SC_ALT_MOUSE_IMAGE opt_syscons.h
761 SC_CUT_SPACES2TABS opt_syscons.h
762 SC_CUT_SEPCHARS opt_syscons.h
763 SC_DEBUG_LEVEL opt_syscons.h
764 SC_DFLT_FONT opt_syscons.h
765 SC_DISABLE_KDBKEY opt_syscons.h
766 SC_DISABLE_REBOOT opt_syscons.h
767 SC_HISTORY_SIZE opt_syscons.h
768 SC_KERNEL_CONS_ATTR opt_syscons.h
769 SC_KERNEL_CONS_REV_ATTR opt_syscons.h
770 SC_MOUSE_CHAR opt_syscons.h
771 SC_NO_CUTPASTE opt_syscons.h
772 SC_NO_FONT_LOADING opt_syscons.h
773 SC_NO_HISTORY opt_syscons.h
774 SC_NO_MODE_CHANGE opt_syscons.h
775 SC_NO_SUSPEND_VTYSWITCH opt_syscons.h
776 SC_NO_SYSMOUSE opt_syscons.h
777 SC_NORM_ATTR opt_syscons.h
778 SC_NORM_REV_ATTR opt_syscons.h
779 SC_PIXEL_MODE opt_syscons.h
780 SC_RENDER_DEBUG opt_syscons.h
781 SC_TWOBUTTON_MOUSE opt_syscons.h
782 VT_ALT_TO_ESC_HACK opt_syscons.h
783 VT_FB_DEFAULT_WIDTH opt_syscons.h
784 VT_FB_DEFAULT_HEIGHT opt_syscons.h
785 VT_MAXWINDOWS opt_syscons.h
786 VT_TWOBUTTON_MOUSE opt_syscons.h
790 # teken terminal emulator options
791 TEKEN_CONS25 opt_teken.h
792 TEKEN_UTF8 opt_teken.h
793 TERMINAL_KERN_ATTR opt_teken.h
794 TERMINAL_NORM_ATTR opt_teken.h
797 PRINTF_BUFR_SIZE opt_printf.h
800 KBD_DISABLE_KEYMAP_LOAD opt_kbd.h
801 KBD_INSTALL_CDEV opt_kbd.h
802 KBD_MAXRETRY opt_kbd.h
803 KBD_MAXWAIT opt_kbd.h
804 KBD_RESETDELAY opt_kbd.h
805 KBDIO_DEBUG opt_kbd.h
807 KBDMUX_DFLT_KEYMAP opt_kbdmux.h
809 # options for the Atheros driver
813 ATH_DIAGAPI opt_ath.h
814 ATH_TX99_DIAG opt_ath.h
815 ATH_ENABLE_11N opt_ath.h
816 ATH_ENABLE_DFS opt_ath.h
817 ATH_EEPROM_FIRMWARE opt_ath.h
818 ATH_ENABLE_RADIOTAP_VENDOR_EXT opt_ath.h
819 ATH_DEBUG_ALQ opt_ath.h
820 ATH_KTR_INTR_DEBUG opt_ath.h
822 # options for the Atheros hal
823 AH_SUPPORT_AR5416 opt_ah.h
824 # XXX For now, this breaks non-AR9130 chipsets, so only use it
825 # XXX when actually targeting AR9130.
826 AH_SUPPORT_AR9130 opt_ah.h
828 # This is required for AR933x SoC support
829 AH_SUPPORT_AR9330 opt_ah.h
830 AH_SUPPORT_AR9340 opt_ah.h
831 AH_SUPPORT_QCA9530 opt_ah.h
832 AH_SUPPORT_QCA9550 opt_ah.h
836 AH_DEBUG_ALQ opt_ah.h
837 AH_REGOPS_FUNC opt_ah.h
838 AH_WRITE_REGDOMAIN opt_ah.h
839 AH_DEBUG_COUNTRY opt_ah.h
840 AH_WRITE_EEPROM opt_ah.h
841 AH_PRIVATE_DIAG opt_ah.h
842 AH_NEED_DESC_SWAP opt_ah.h
843 AH_USE_INIPDGAIN opt_ah.h
845 AH_RXCFG_SDMAMW_4BYTES opt_ah.h
846 AH_INTERRUPT_DEBUGGING opt_ah.h
847 # AR5416 and later interrupt mitigation
848 # XXX do not use this for AR9130
849 AH_AR5416_INTERRUPT_MITIGATION opt_ah.h
851 # options for the Broadcom BCM43xx driver (bwi)
853 BWI_DEBUG_VERBOSE opt_bwi.h
855 # options for the Brodacom BCM43xx driver (bwn)
857 BWN_GPL_PHY opt_bwn.h
859 # Options for the SIBA driver
860 SIBA_DEBUG opt_siba.h
862 # options for the Marvell 8335 wireless driver
863 MALO_DEBUG opt_malo.h
864 MALO_TXBUF opt_malo.h
865 MALO_RXBUF opt_malo.h
867 # options for the Marvell wireless driver
871 MWL_DIAGAPI opt_mwl.h
872 MWL_AGGR_SIZE opt_mwl.h
873 MWL_TX_NODROP opt_mwl.h
875 # Options for the Marvell NETA driver
876 MVNETA_MULTIQUEUE opt_mvneta.h
877 MVNETA_KTR opt_mvneta.h
879 # Options for the Intel 802.11ac wireless driver
882 # Options for the Intel 802.11n wireless driver
885 # Options for the Intel 3945ABG wireless driver
889 DCONS_BUF_SIZE opt_dcons.h
890 DCONS_POLL_HZ opt_dcons.h
891 DCONS_FORCE_CONSOLE opt_dcons.h
892 DCONS_FORCE_GDB opt_dcons.h
895 HWPMC_DEBUG opt_global.h
897 HWPMC_MIPS_BACKTRACE opt_hwpmc_hooks.h
899 # XBOX options for FreeBSD/i386, but some files are MI
902 # Interrupt filtering
905 # 802.11 support layer
906 IEEE80211_DEBUG opt_wlan.h
907 IEEE80211_DEBUG_REFCNT opt_wlan.h
908 IEEE80211_AMPDU_AGE opt_wlan.h
909 IEEE80211_SUPPORT_MESH opt_wlan.h
910 IEEE80211_SUPPORT_SUPERG opt_wlan.h
911 IEEE80211_SUPPORT_TDMA opt_wlan.h
912 IEEE80211_ALQ opt_wlan.h
913 IEEE80211_DFS_DEBUG opt_wlan.h
915 # 802.11 TDMA support
916 TDMA_SLOTLEN_DEFAULT opt_tdma.h
917 TDMA_SLOTCNT_DEFAULT opt_tdma.h
918 TDMA_BINTVAL_DEFAULT opt_tdma.h
919 TDMA_TXRATE_11B_DEFAULT opt_tdma.h
920 TDMA_TXRATE_11G_DEFAULT opt_tdma.h
921 TDMA_TXRATE_11A_DEFAULT opt_tdma.h
922 TDMA_TXRATE_TURBO_DEFAULT opt_tdma.h
923 TDMA_TXRATE_HALF_DEFAULT opt_tdma.h
924 TDMA_TXRATE_QUARTER_DEFAULT opt_tdma.h
925 TDMA_TXRATE_11NA_DEFAULT opt_tdma.h
926 TDMA_TXRATE_11NG_DEFAULT opt_tdma.h
929 PICKMODE_DEBUG opt_videomode.h
931 # Network stack virtualization options
933 VNET_DEBUG opt_global.h
935 # Common Flash Interface (CFI) options
936 CFI_SUPPORT_STRATAFLASH opt_cfi.h
937 CFI_ARMEDANDDANGEROUS opt_cfi.h
938 CFI_HARDWAREBYTESWAP opt_cfi.h
942 SND_DIAGNOSTIC opt_snd.h
943 SND_FEEDER_MULTIFORMAT opt_snd.h
944 SND_FEEDER_FULL_MULTIFORMAT opt_snd.h
945 SND_FEEDER_RATE_HP opt_snd.h
947 SND_OLDSTEREO opt_snd.h
951 # Flattened device tree options
953 FDT_DTB_STATIC opt_platform.h
955 # OFED Infiniband stack
957 OFED_DEBUG_INIT opt_ofed.h
961 IPOIB_DEBUG opt_ofed.h
964 # Resource Accounting
966 RACCT_DEFAULT_TO_DISABLED opt_global.h
971 # Random number generator(s)
972 # Which CSPRNG hash we get.
973 # If Yarrow is not chosen, Fortuna is selected.
974 RANDOM_YARROW opt_global.h
975 # With this, no entropy processor is loaded, but the entropy
976 # harvesting infrastructure is present. This means an entropy
977 # processor may be loaded as a module.
978 RANDOM_LOADABLE opt_global.h
979 # This turns on high-rate and potentially expensive harvesting in
980 # the uma slab allocator.
981 RANDOM_ENABLE_UMA opt_global.h
984 BHND_LOGLEVEL opt_global.h
986 # GPIO and child devices
987 GPIO_SPI_DEBUG opt_gpio.h
989 # etherswitch(4) driver
990 RTL8366_SOFT_RESET opt_etherswitch.h
992 # evdev protocol support
993 EVDEV_SUPPORT opt_evdev.h
994 EVDEV_DEBUG opt_evdev.h
995 UINPUT_DEBUG opt_evdev.h
997 # Hyper-V network driver
1000 # Encrypted kernel crash dumps