2 * Copyright (c) 2007-2009 Damien Bergamini <damien.bergamini@free.fr>
3 * Copyright (c) 2008 Benjamin Close <benjsc@FreeBSD.org>
4 * Copyright (c) 2008 Sam Leffler, Errno Consulting
5 * Copyright (c) 2011 Intel Corporation
6 * Copyright (c) 2013 Cedric GROSS <c.gross@kreiz-it.fr>
7 * Copyright (c) 2013 Adrian Chadd <adrian@FreeBSD.org>
9 * Permission to use, copy, modify, and distribute this software for any
10 * purpose with or without fee is hereby granted, provided that the above
11 * copyright notice and this permission notice appear in all copies.
13 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
14 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
15 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
16 * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
17 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
18 * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
19 * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
23 * Driver for Intel WiFi Link 4965 and 1000/5000/6000 Series 802.11 network
27 #include <sys/cdefs.h>
28 __FBSDID("$FreeBSD$");
33 #include <sys/param.h>
34 #include <sys/sockio.h>
35 #include <sys/sysctl.h>
37 #include <sys/kernel.h>
38 #include <sys/socket.h>
39 #include <sys/systm.h>
40 #include <sys/malloc.h>
44 #include <sys/endian.h>
45 #include <sys/firmware.h>
46 #include <sys/limits.h>
47 #include <sys/module.h>
49 #include <sys/queue.h>
50 #include <sys/taskqueue.h>
52 #include <machine/bus.h>
53 #include <machine/resource.h>
54 #include <machine/clock.h>
56 #include <dev/pci/pcireg.h>
57 #include <dev/pci/pcivar.h>
60 #include <net/if_var.h>
61 #include <net/if_dl.h>
62 #include <net/if_media.h>
64 #include <netinet/in.h>
65 #include <netinet/if_ether.h>
67 #include <net80211/ieee80211_var.h>
68 #include <net80211/ieee80211_radiotap.h>
69 #include <net80211/ieee80211_regdomain.h>
70 #include <net80211/ieee80211_ratectl.h>
72 #include <dev/iwn/if_iwnreg.h>
73 #include <dev/iwn/if_iwnvar.h>
74 #include <dev/iwn/if_iwn_devid.h>
75 #include <dev/iwn/if_iwn_chip_cfg.h>
76 #include <dev/iwn/if_iwn_debug.h>
77 #include <dev/iwn/if_iwn_ioctl.h>
85 static const struct iwn_ident iwn_ident_table[] = {
86 { 0x8086, IWN_DID_6x05_1, "Intel Centrino Advanced-N 6205" },
87 { 0x8086, IWN_DID_1000_1, "Intel Centrino Wireless-N 1000" },
88 { 0x8086, IWN_DID_1000_2, "Intel Centrino Wireless-N 1000" },
89 { 0x8086, IWN_DID_6x05_2, "Intel Centrino Advanced-N 6205" },
90 { 0x8086, IWN_DID_6050_1, "Intel Centrino Advanced-N + WiMAX 6250" },
91 { 0x8086, IWN_DID_6050_2, "Intel Centrino Advanced-N + WiMAX 6250" },
92 { 0x8086, IWN_DID_x030_1, "Intel Centrino Wireless-N 1030" },
93 { 0x8086, IWN_DID_x030_2, "Intel Centrino Wireless-N 1030" },
94 { 0x8086, IWN_DID_x030_3, "Intel Centrino Advanced-N 6230" },
95 { 0x8086, IWN_DID_x030_4, "Intel Centrino Advanced-N 6230" },
96 { 0x8086, IWN_DID_6150_1, "Intel Centrino Wireless-N + WiMAX 6150" },
97 { 0x8086, IWN_DID_6150_2, "Intel Centrino Wireless-N + WiMAX 6150" },
98 { 0x8086, IWN_DID_2x00_1, "Intel(R) Centrino(R) Wireless-N 2200 BGN" },
99 { 0x8086, IWN_DID_2x00_2, "Intel(R) Centrino(R) Wireless-N 2200 BGN" },
100 /* XXX 2200D is IWN_SDID_2x00_4; there's no way to express this here! */
101 { 0x8086, IWN_DID_2x30_1, "Intel Centrino Wireless-N 2230" },
102 { 0x8086, IWN_DID_2x30_2, "Intel Centrino Wireless-N 2230" },
103 { 0x8086, IWN_DID_130_1, "Intel Centrino Wireless-N 130" },
104 { 0x8086, IWN_DID_130_2, "Intel Centrino Wireless-N 130" },
105 { 0x8086, IWN_DID_100_1, "Intel Centrino Wireless-N 100" },
106 { 0x8086, IWN_DID_100_2, "Intel Centrino Wireless-N 100" },
107 { 0x8086, IWN_DID_105_1, "Intel Centrino Wireless-N 105" },
108 { 0x8086, IWN_DID_105_2, "Intel Centrino Wireless-N 105" },
109 { 0x8086, IWN_DID_135_1, "Intel Centrino Wireless-N 135" },
110 { 0x8086, IWN_DID_135_2, "Intel Centrino Wireless-N 135" },
111 { 0x8086, IWN_DID_4965_1, "Intel Wireless WiFi Link 4965" },
112 { 0x8086, IWN_DID_6x00_1, "Intel Centrino Ultimate-N 6300" },
113 { 0x8086, IWN_DID_6x00_2, "Intel Centrino Advanced-N 6200" },
114 { 0x8086, IWN_DID_4965_2, "Intel Wireless WiFi Link 4965" },
115 { 0x8086, IWN_DID_4965_3, "Intel Wireless WiFi Link 4965" },
116 { 0x8086, IWN_DID_5x00_1, "Intel WiFi Link 5100" },
117 { 0x8086, IWN_DID_4965_4, "Intel Wireless WiFi Link 4965" },
118 { 0x8086, IWN_DID_5x00_3, "Intel Ultimate N WiFi Link 5300" },
119 { 0x8086, IWN_DID_5x00_4, "Intel Ultimate N WiFi Link 5300" },
120 { 0x8086, IWN_DID_5x00_2, "Intel WiFi Link 5100" },
121 { 0x8086, IWN_DID_6x00_3, "Intel Centrino Ultimate-N 6300" },
122 { 0x8086, IWN_DID_6x00_4, "Intel Centrino Advanced-N 6200" },
123 { 0x8086, IWN_DID_5x50_1, "Intel WiMAX/WiFi Link 5350" },
124 { 0x8086, IWN_DID_5x50_2, "Intel WiMAX/WiFi Link 5350" },
125 { 0x8086, IWN_DID_5x50_3, "Intel WiMAX/WiFi Link 5150" },
126 { 0x8086, IWN_DID_5x50_4, "Intel WiMAX/WiFi Link 5150" },
127 { 0x8086, IWN_DID_6035_1, "Intel Centrino Advanced 6235" },
128 { 0x8086, IWN_DID_6035_2, "Intel Centrino Advanced 6235" },
132 static int iwn_probe(device_t);
133 static int iwn_attach(device_t);
134 static void iwn4965_attach(struct iwn_softc *, uint16_t);
135 static void iwn5000_attach(struct iwn_softc *, uint16_t);
136 static int iwn_config_specific(struct iwn_softc *, uint16_t);
137 static void iwn_radiotap_attach(struct iwn_softc *);
138 static void iwn_sysctlattach(struct iwn_softc *);
139 static struct ieee80211vap *iwn_vap_create(struct ieee80211com *,
140 const char [IFNAMSIZ], int, enum ieee80211_opmode, int,
141 const uint8_t [IEEE80211_ADDR_LEN],
142 const uint8_t [IEEE80211_ADDR_LEN]);
143 static void iwn_vap_delete(struct ieee80211vap *);
144 static int iwn_detach(device_t);
145 static int iwn_shutdown(device_t);
146 static int iwn_suspend(device_t);
147 static int iwn_resume(device_t);
148 static int iwn_nic_lock(struct iwn_softc *);
149 static int iwn_eeprom_lock(struct iwn_softc *);
150 static int iwn_init_otprom(struct iwn_softc *);
151 static int iwn_read_prom_data(struct iwn_softc *, uint32_t, void *, int);
152 static void iwn_dma_map_addr(void *, bus_dma_segment_t *, int, int);
153 static int iwn_dma_contig_alloc(struct iwn_softc *, struct iwn_dma_info *,
154 void **, bus_size_t, bus_size_t);
155 static void iwn_dma_contig_free(struct iwn_dma_info *);
156 static int iwn_alloc_sched(struct iwn_softc *);
157 static void iwn_free_sched(struct iwn_softc *);
158 static int iwn_alloc_kw(struct iwn_softc *);
159 static void iwn_free_kw(struct iwn_softc *);
160 static int iwn_alloc_ict(struct iwn_softc *);
161 static void iwn_free_ict(struct iwn_softc *);
162 static int iwn_alloc_fwmem(struct iwn_softc *);
163 static void iwn_free_fwmem(struct iwn_softc *);
164 static int iwn_alloc_rx_ring(struct iwn_softc *, struct iwn_rx_ring *);
165 static void iwn_reset_rx_ring(struct iwn_softc *, struct iwn_rx_ring *);
166 static void iwn_free_rx_ring(struct iwn_softc *, struct iwn_rx_ring *);
167 static int iwn_alloc_tx_ring(struct iwn_softc *, struct iwn_tx_ring *,
169 static void iwn_reset_tx_ring(struct iwn_softc *, struct iwn_tx_ring *);
170 static void iwn_free_tx_ring(struct iwn_softc *, struct iwn_tx_ring *);
171 static void iwn5000_ict_reset(struct iwn_softc *);
172 static int iwn_read_eeprom(struct iwn_softc *,
173 uint8_t macaddr[IEEE80211_ADDR_LEN]);
174 static void iwn4965_read_eeprom(struct iwn_softc *);
176 static void iwn4965_print_power_group(struct iwn_softc *, int);
178 static void iwn5000_read_eeprom(struct iwn_softc *);
179 static uint32_t iwn_eeprom_channel_flags(struct iwn_eeprom_chan *);
180 static void iwn_read_eeprom_band(struct iwn_softc *, int, int, int *,
181 struct ieee80211_channel[]);
182 static void iwn_read_eeprom_ht40(struct iwn_softc *, int, int, int *,
183 struct ieee80211_channel[]);
184 static void iwn_read_eeprom_channels(struct iwn_softc *, int, uint32_t);
185 static struct iwn_eeprom_chan *iwn_find_eeprom_channel(struct iwn_softc *,
186 struct ieee80211_channel *);
187 static void iwn_getradiocaps(struct ieee80211com *, int, int *,
188 struct ieee80211_channel[]);
189 static int iwn_setregdomain(struct ieee80211com *,
190 struct ieee80211_regdomain *, int,
191 struct ieee80211_channel[]);
192 static void iwn_read_eeprom_enhinfo(struct iwn_softc *);
193 static struct ieee80211_node *iwn_node_alloc(struct ieee80211vap *,
194 const uint8_t mac[IEEE80211_ADDR_LEN]);
195 static void iwn_newassoc(struct ieee80211_node *, int);
196 static int iwn_media_change(struct ifnet *);
197 static int iwn_newstate(struct ieee80211vap *, enum ieee80211_state, int);
198 static void iwn_calib_timeout(void *);
199 static void iwn_rx_phy(struct iwn_softc *, struct iwn_rx_desc *,
200 struct iwn_rx_data *);
201 static void iwn_rx_done(struct iwn_softc *, struct iwn_rx_desc *,
202 struct iwn_rx_data *);
203 static void iwn_rx_compressed_ba(struct iwn_softc *, struct iwn_rx_desc *,
204 struct iwn_rx_data *);
205 static void iwn5000_rx_calib_results(struct iwn_softc *,
206 struct iwn_rx_desc *, struct iwn_rx_data *);
207 static void iwn_rx_statistics(struct iwn_softc *, struct iwn_rx_desc *,
208 struct iwn_rx_data *);
209 static void iwn4965_tx_done(struct iwn_softc *, struct iwn_rx_desc *,
210 struct iwn_rx_data *);
211 static void iwn5000_tx_done(struct iwn_softc *, struct iwn_rx_desc *,
212 struct iwn_rx_data *);
213 static void iwn_tx_done(struct iwn_softc *, struct iwn_rx_desc *, int,
215 static void iwn_ampdu_tx_done(struct iwn_softc *, int, int, int, int, void *);
216 static void iwn_cmd_done(struct iwn_softc *, struct iwn_rx_desc *);
217 static void iwn_notif_intr(struct iwn_softc *);
218 static void iwn_wakeup_intr(struct iwn_softc *);
219 static void iwn_rftoggle_intr(struct iwn_softc *);
220 static void iwn_fatal_intr(struct iwn_softc *);
221 static void iwn_intr(void *);
222 static void iwn4965_update_sched(struct iwn_softc *, int, int, uint8_t,
224 static void iwn5000_update_sched(struct iwn_softc *, int, int, uint8_t,
227 static void iwn5000_reset_sched(struct iwn_softc *, int, int);
229 static int iwn_tx_data(struct iwn_softc *, struct mbuf *,
230 struct ieee80211_node *);
231 static int iwn_tx_data_raw(struct iwn_softc *, struct mbuf *,
232 struct ieee80211_node *,
233 const struct ieee80211_bpf_params *params);
234 static void iwn_xmit_task(void *arg0, int pending);
235 static int iwn_raw_xmit(struct ieee80211_node *, struct mbuf *,
236 const struct ieee80211_bpf_params *);
237 static int iwn_transmit(struct ieee80211com *, struct mbuf *);
238 static void iwn_scan_timeout(void *);
239 static void iwn_watchdog(void *);
240 static int iwn_ioctl(struct ieee80211com *, u_long , void *);
241 static void iwn_parent(struct ieee80211com *);
242 static int iwn_cmd(struct iwn_softc *, int, const void *, int, int);
243 static int iwn4965_add_node(struct iwn_softc *, struct iwn_node_info *,
245 static int iwn5000_add_node(struct iwn_softc *, struct iwn_node_info *,
247 static int iwn_set_link_quality(struct iwn_softc *,
248 struct ieee80211_node *);
249 static int iwn_add_broadcast_node(struct iwn_softc *, int);
250 static int iwn_updateedca(struct ieee80211com *);
251 static void iwn_update_mcast(struct ieee80211com *);
252 static void iwn_set_led(struct iwn_softc *, uint8_t, uint8_t, uint8_t);
253 static int iwn_set_critical_temp(struct iwn_softc *);
254 static int iwn_set_timing(struct iwn_softc *, struct ieee80211_node *);
255 static void iwn4965_power_calibration(struct iwn_softc *, int);
256 static int iwn4965_set_txpower(struct iwn_softc *,
257 struct ieee80211_channel *, int);
258 static int iwn5000_set_txpower(struct iwn_softc *,
259 struct ieee80211_channel *, int);
260 static int iwn4965_get_rssi(struct iwn_softc *, struct iwn_rx_stat *);
261 static int iwn5000_get_rssi(struct iwn_softc *, struct iwn_rx_stat *);
262 static int iwn_get_noise(const struct iwn_rx_general_stats *);
263 static int iwn4965_get_temperature(struct iwn_softc *);
264 static int iwn5000_get_temperature(struct iwn_softc *);
265 static int iwn_init_sensitivity(struct iwn_softc *);
266 static void iwn_collect_noise(struct iwn_softc *,
267 const struct iwn_rx_general_stats *);
268 static int iwn4965_init_gains(struct iwn_softc *);
269 static int iwn5000_init_gains(struct iwn_softc *);
270 static int iwn4965_set_gains(struct iwn_softc *);
271 static int iwn5000_set_gains(struct iwn_softc *);
272 static void iwn_tune_sensitivity(struct iwn_softc *,
273 const struct iwn_rx_stats *);
274 static void iwn_save_stats_counters(struct iwn_softc *,
275 const struct iwn_stats *);
276 static int iwn_send_sensitivity(struct iwn_softc *);
277 static void iwn_check_rx_recovery(struct iwn_softc *, struct iwn_stats *);
278 static int iwn_set_pslevel(struct iwn_softc *, int, int, int);
279 static int iwn_send_btcoex(struct iwn_softc *);
280 static int iwn_send_advanced_btcoex(struct iwn_softc *);
281 static int iwn5000_runtime_calib(struct iwn_softc *);
282 static int iwn_config(struct iwn_softc *);
283 static int iwn_scan(struct iwn_softc *, struct ieee80211vap *,
284 struct ieee80211_scan_state *, struct ieee80211_channel *);
285 static int iwn_auth(struct iwn_softc *, struct ieee80211vap *vap);
286 static int iwn_run(struct iwn_softc *, struct ieee80211vap *vap);
287 static int iwn_ampdu_rx_start(struct ieee80211_node *,
288 struct ieee80211_rx_ampdu *, int, int, int);
289 static void iwn_ampdu_rx_stop(struct ieee80211_node *,
290 struct ieee80211_rx_ampdu *);
291 static int iwn_addba_request(struct ieee80211_node *,
292 struct ieee80211_tx_ampdu *, int, int, int);
293 static int iwn_addba_response(struct ieee80211_node *,
294 struct ieee80211_tx_ampdu *, int, int, int);
295 static int iwn_ampdu_tx_start(struct ieee80211com *,
296 struct ieee80211_node *, uint8_t);
297 static void iwn_ampdu_tx_stop(struct ieee80211_node *,
298 struct ieee80211_tx_ampdu *);
299 static void iwn4965_ampdu_tx_start(struct iwn_softc *,
300 struct ieee80211_node *, int, uint8_t, uint16_t);
301 static void iwn4965_ampdu_tx_stop(struct iwn_softc *, int,
303 static void iwn5000_ampdu_tx_start(struct iwn_softc *,
304 struct ieee80211_node *, int, uint8_t, uint16_t);
305 static void iwn5000_ampdu_tx_stop(struct iwn_softc *, int,
307 static int iwn5000_query_calibration(struct iwn_softc *);
308 static int iwn5000_send_calibration(struct iwn_softc *);
309 static int iwn5000_send_wimax_coex(struct iwn_softc *);
310 static int iwn5000_crystal_calib(struct iwn_softc *);
311 static int iwn5000_temp_offset_calib(struct iwn_softc *);
312 static int iwn5000_temp_offset_calibv2(struct iwn_softc *);
313 static int iwn4965_post_alive(struct iwn_softc *);
314 static int iwn5000_post_alive(struct iwn_softc *);
315 static int iwn4965_load_bootcode(struct iwn_softc *, const uint8_t *,
317 static int iwn4965_load_firmware(struct iwn_softc *);
318 static int iwn5000_load_firmware_section(struct iwn_softc *, uint32_t,
319 const uint8_t *, int);
320 static int iwn5000_load_firmware(struct iwn_softc *);
321 static int iwn_read_firmware_leg(struct iwn_softc *,
322 struct iwn_fw_info *);
323 static int iwn_read_firmware_tlv(struct iwn_softc *,
324 struct iwn_fw_info *, uint16_t);
325 static int iwn_read_firmware(struct iwn_softc *);
326 static void iwn_unload_firmware(struct iwn_softc *);
327 static int iwn_clock_wait(struct iwn_softc *);
328 static int iwn_apm_init(struct iwn_softc *);
329 static void iwn_apm_stop_master(struct iwn_softc *);
330 static void iwn_apm_stop(struct iwn_softc *);
331 static int iwn4965_nic_config(struct iwn_softc *);
332 static int iwn5000_nic_config(struct iwn_softc *);
333 static int iwn_hw_prepare(struct iwn_softc *);
334 static int iwn_hw_init(struct iwn_softc *);
335 static void iwn_hw_stop(struct iwn_softc *);
336 static void iwn_radio_on(void *, int);
337 static void iwn_radio_off(void *, int);
338 static void iwn_panicked(void *, int);
339 static void iwn_init_locked(struct iwn_softc *);
340 static void iwn_init(struct iwn_softc *);
341 static void iwn_stop_locked(struct iwn_softc *);
342 static void iwn_stop(struct iwn_softc *);
343 static void iwn_scan_start(struct ieee80211com *);
344 static void iwn_scan_end(struct ieee80211com *);
345 static void iwn_set_channel(struct ieee80211com *);
346 static void iwn_scan_curchan(struct ieee80211_scan_state *, unsigned long);
347 static void iwn_scan_mindwell(struct ieee80211_scan_state *);
349 static char *iwn_get_csr_string(int);
350 static void iwn_debug_register(struct iwn_softc *);
353 static device_method_t iwn_methods[] = {
354 /* Device interface */
355 DEVMETHOD(device_probe, iwn_probe),
356 DEVMETHOD(device_attach, iwn_attach),
357 DEVMETHOD(device_detach, iwn_detach),
358 DEVMETHOD(device_shutdown, iwn_shutdown),
359 DEVMETHOD(device_suspend, iwn_suspend),
360 DEVMETHOD(device_resume, iwn_resume),
365 static driver_t iwn_driver = {
368 sizeof(struct iwn_softc)
370 static devclass_t iwn_devclass;
372 DRIVER_MODULE(iwn, pci, iwn_driver, iwn_devclass, NULL, NULL);
374 MODULE_VERSION(iwn, 1);
376 MODULE_DEPEND(iwn, firmware, 1, 1, 1);
377 MODULE_DEPEND(iwn, pci, 1, 1, 1);
378 MODULE_DEPEND(iwn, wlan, 1, 1, 1);
380 static d_ioctl_t iwn_cdev_ioctl;
381 static d_open_t iwn_cdev_open;
382 static d_close_t iwn_cdev_close;
384 static struct cdevsw iwn_cdevsw = {
385 .d_version = D_VERSION,
387 .d_open = iwn_cdev_open,
388 .d_close = iwn_cdev_close,
389 .d_ioctl = iwn_cdev_ioctl,
394 iwn_probe(device_t dev)
396 const struct iwn_ident *ident;
398 for (ident = iwn_ident_table; ident->name != NULL; ident++) {
399 if (pci_get_vendor(dev) == ident->vendor &&
400 pci_get_device(dev) == ident->device) {
401 device_set_desc(dev, ident->name);
402 return (BUS_PROBE_DEFAULT);
409 iwn_is_3stream_device(struct iwn_softc *sc)
411 /* XXX for now only 5300, until the 5350 can be tested */
412 if (sc->hw_type == IWN_HW_REV_TYPE_5300)
418 iwn_attach(device_t dev)
420 struct iwn_softc *sc = device_get_softc(dev);
421 struct ieee80211com *ic;
427 error = resource_int_value(device_get_name(sc->sc_dev),
428 device_get_unit(sc->sc_dev), "debug", &(sc->sc_debug));
435 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: begin\n",__func__);
438 * Get the offset of the PCI Express Capability Structure in PCI
439 * Configuration Space.
441 error = pci_find_cap(dev, PCIY_EXPRESS, &sc->sc_cap_off);
443 device_printf(dev, "PCIe capability structure not found!\n");
447 /* Clear device-specific "PCI retry timeout" register (41h). */
448 pci_write_config(dev, 0x41, 0, 1);
450 /* Enable bus-mastering. */
451 pci_enable_busmaster(dev);
454 sc->mem = bus_alloc_resource_any(dev, SYS_RES_MEMORY, &rid,
456 if (sc->mem == NULL) {
457 device_printf(dev, "can't map mem space\n");
461 sc->sc_st = rman_get_bustag(sc->mem);
462 sc->sc_sh = rman_get_bushandle(sc->mem);
466 if (pci_alloc_msi(dev, &i) == 0)
468 /* Install interrupt handler. */
469 sc->irq = bus_alloc_resource_any(dev, SYS_RES_IRQ, &rid, RF_ACTIVE |
470 (rid != 0 ? 0 : RF_SHAREABLE));
471 if (sc->irq == NULL) {
472 device_printf(dev, "can't map interrupt\n");
479 /* Read hardware revision and attach. */
480 sc->hw_type = (IWN_READ(sc, IWN_HW_REV) >> IWN_HW_REV_TYPE_SHIFT)
481 & IWN_HW_REV_TYPE_MASK;
482 sc->subdevice_id = pci_get_subdevice(dev);
485 * 4965 versus 5000 and later have different methods.
486 * Let's set those up first.
488 if (sc->hw_type == IWN_HW_REV_TYPE_4965)
489 iwn4965_attach(sc, pci_get_device(dev));
491 iwn5000_attach(sc, pci_get_device(dev));
494 * Next, let's setup the various parameters of each NIC.
496 error = iwn_config_specific(sc, pci_get_device(dev));
498 device_printf(dev, "could not attach device, error %d\n",
503 if ((error = iwn_hw_prepare(sc)) != 0) {
504 device_printf(dev, "hardware not ready, error %d\n", error);
508 /* Allocate DMA memory for firmware transfers. */
509 if ((error = iwn_alloc_fwmem(sc)) != 0) {
511 "could not allocate memory for firmware, error %d\n",
516 /* Allocate "Keep Warm" page. */
517 if ((error = iwn_alloc_kw(sc)) != 0) {
519 "could not allocate keep warm page, error %d\n", error);
523 /* Allocate ICT table for 5000 Series. */
524 if (sc->hw_type != IWN_HW_REV_TYPE_4965 &&
525 (error = iwn_alloc_ict(sc)) != 0) {
526 device_printf(dev, "could not allocate ICT table, error %d\n",
531 /* Allocate TX scheduler "rings". */
532 if ((error = iwn_alloc_sched(sc)) != 0) {
534 "could not allocate TX scheduler rings, error %d\n", error);
538 /* Allocate TX rings (16 on 4965AGN, 20 on >=5000). */
539 for (i = 0; i < sc->ntxqs; i++) {
540 if ((error = iwn_alloc_tx_ring(sc, &sc->txq[i], i)) != 0) {
542 "could not allocate TX ring %d, error %d\n", i,
548 /* Allocate RX ring. */
549 if ((error = iwn_alloc_rx_ring(sc, &sc->rxq)) != 0) {
550 device_printf(dev, "could not allocate RX ring, error %d\n",
555 /* Clear pending interrupts. */
556 IWN_WRITE(sc, IWN_INT, 0xffffffff);
560 ic->ic_name = device_get_nameunit(dev);
561 ic->ic_phytype = IEEE80211_T_OFDM; /* not only, but not used */
562 ic->ic_opmode = IEEE80211_M_STA; /* default to BSS mode */
564 /* Set device capabilities. */
566 IEEE80211_C_STA /* station mode supported */
567 | IEEE80211_C_MONITOR /* monitor mode supported */
569 | IEEE80211_C_BGSCAN /* background scanning */
571 | IEEE80211_C_TXPMGT /* tx power management */
572 | IEEE80211_C_SHSLOT /* short slot time supported */
574 | IEEE80211_C_SHPREAMBLE /* short preamble supported */
576 | IEEE80211_C_IBSS /* ibss/adhoc mode */
578 | IEEE80211_C_WME /* WME */
579 | IEEE80211_C_PMGT /* Station-side power mgmt */
582 /* Read MAC address, channels, etc from EEPROM. */
583 if ((error = iwn_read_eeprom(sc, ic->ic_macaddr)) != 0) {
584 device_printf(dev, "could not read EEPROM, error %d\n",
589 /* Count the number of available chains. */
591 ((sc->txchainmask >> 2) & 1) +
592 ((sc->txchainmask >> 1) & 1) +
593 ((sc->txchainmask >> 0) & 1);
595 ((sc->rxchainmask >> 2) & 1) +
596 ((sc->rxchainmask >> 1) & 1) +
597 ((sc->rxchainmask >> 0) & 1);
599 device_printf(dev, "MIMO %dT%dR, %.4s, address %6D\n",
600 sc->ntxchains, sc->nrxchains, sc->eeprom_domain,
601 ic->ic_macaddr, ":");
604 if (sc->sc_flags & IWN_FLAG_HAS_11N) {
605 ic->ic_rxstream = sc->nrxchains;
606 ic->ic_txstream = sc->ntxchains;
609 * Some of the 3 antenna devices (ie, the 4965) only supports
610 * 2x2 operation. So correct the number of streams if
611 * it's not a 3-stream device.
613 if (! iwn_is_3stream_device(sc)) {
614 if (ic->ic_rxstream > 2)
616 if (ic->ic_txstream > 2)
621 IEEE80211_HTCAP_SMPS_OFF /* SMPS mode disabled */
622 | IEEE80211_HTCAP_SHORTGI20 /* short GI in 20MHz */
623 | IEEE80211_HTCAP_CHWIDTH40 /* 40MHz channel width*/
624 | IEEE80211_HTCAP_SHORTGI40 /* short GI in 40MHz */
626 | IEEE80211_HTCAP_GREENFIELD
627 #if IWN_RBUF_SIZE == 8192
628 | IEEE80211_HTCAP_MAXAMSDU_7935 /* max A-MSDU length */
630 | IEEE80211_HTCAP_MAXAMSDU_3839 /* max A-MSDU length */
633 /* s/w capabilities */
634 | IEEE80211_HTC_HT /* HT operation */
635 | IEEE80211_HTC_AMPDU /* tx A-MPDU */
637 | IEEE80211_HTC_AMSDU /* tx A-MSDU */
642 ieee80211_ifattach(ic);
643 ic->ic_vap_create = iwn_vap_create;
644 ic->ic_ioctl = iwn_ioctl;
645 ic->ic_parent = iwn_parent;
646 ic->ic_vap_delete = iwn_vap_delete;
647 ic->ic_transmit = iwn_transmit;
648 ic->ic_raw_xmit = iwn_raw_xmit;
649 ic->ic_node_alloc = iwn_node_alloc;
650 sc->sc_ampdu_rx_start = ic->ic_ampdu_rx_start;
651 ic->ic_ampdu_rx_start = iwn_ampdu_rx_start;
652 sc->sc_ampdu_rx_stop = ic->ic_ampdu_rx_stop;
653 ic->ic_ampdu_rx_stop = iwn_ampdu_rx_stop;
654 sc->sc_addba_request = ic->ic_addba_request;
655 ic->ic_addba_request = iwn_addba_request;
656 sc->sc_addba_response = ic->ic_addba_response;
657 ic->ic_addba_response = iwn_addba_response;
658 sc->sc_addba_stop = ic->ic_addba_stop;
659 ic->ic_addba_stop = iwn_ampdu_tx_stop;
660 ic->ic_newassoc = iwn_newassoc;
661 ic->ic_wme.wme_update = iwn_updateedca;
662 ic->ic_update_mcast = iwn_update_mcast;
663 ic->ic_scan_start = iwn_scan_start;
664 ic->ic_scan_end = iwn_scan_end;
665 ic->ic_set_channel = iwn_set_channel;
666 ic->ic_scan_curchan = iwn_scan_curchan;
667 ic->ic_scan_mindwell = iwn_scan_mindwell;
668 ic->ic_getradiocaps = iwn_getradiocaps;
669 ic->ic_setregdomain = iwn_setregdomain;
671 iwn_radiotap_attach(sc);
673 callout_init_mtx(&sc->calib_to, &sc->sc_mtx, 0);
674 callout_init_mtx(&sc->scan_timeout, &sc->sc_mtx, 0);
675 callout_init_mtx(&sc->watchdog_to, &sc->sc_mtx, 0);
676 TASK_INIT(&sc->sc_radioon_task, 0, iwn_radio_on, sc);
677 TASK_INIT(&sc->sc_radiooff_task, 0, iwn_radio_off, sc);
678 TASK_INIT(&sc->sc_panic_task, 0, iwn_panicked, sc);
679 TASK_INIT(&sc->sc_xmit_task, 0, iwn_xmit_task, sc);
681 mbufq_init(&sc->sc_xmit_queue, 1024);
683 sc->sc_tq = taskqueue_create("iwn_taskq", M_WAITOK,
684 taskqueue_thread_enqueue, &sc->sc_tq);
685 error = taskqueue_start_threads(&sc->sc_tq, 1, 0, "iwn_taskq");
687 device_printf(dev, "can't start threads, error %d\n", error);
691 iwn_sysctlattach(sc);
694 * Hook our interrupt after all initialization is complete.
696 error = bus_setup_intr(dev, sc->irq, INTR_TYPE_NET | INTR_MPSAFE,
697 NULL, iwn_intr, sc, &sc->sc_ih);
699 device_printf(dev, "can't establish interrupt, error %d\n",
705 device_printf(sc->sc_dev, "%s: rx_stats=%d, rx_stats_bt=%d\n",
707 sizeof(struct iwn_stats),
708 sizeof(struct iwn_stats_bt));
712 ieee80211_announce(ic);
713 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
715 /* Add debug ioctl right at the end */
716 sc->sc_cdev = make_dev(&iwn_cdevsw, device_get_unit(dev),
717 UID_ROOT, GID_WHEEL, 0600, "%s", device_get_nameunit(dev));
718 if (sc->sc_cdev == NULL) {
719 device_printf(dev, "failed to create debug character device\n");
721 sc->sc_cdev->si_drv1 = sc;
726 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end in error\n",__func__);
731 * Define specific configuration based on device id and subdevice id
732 * pid : PCI device id
735 iwn_config_specific(struct iwn_softc *sc, uint16_t pid)
744 sc->base_params = &iwn4965_base_params;
745 sc->limits = &iwn4965_sensitivity_limits;
746 sc->fwname = "iwn4965fw";
747 /* Override chains masks, ROM is known to be broken. */
748 sc->txchainmask = IWN_ANT_AB;
749 sc->rxchainmask = IWN_ANT_ABC;
750 /* Enable normal btcoex */
751 sc->sc_flags |= IWN_FLAG_BTCOEX;
756 switch(sc->subdevice_id) {
757 case IWN_SDID_1000_1:
758 case IWN_SDID_1000_2:
759 case IWN_SDID_1000_3:
760 case IWN_SDID_1000_4:
761 case IWN_SDID_1000_5:
762 case IWN_SDID_1000_6:
763 case IWN_SDID_1000_7:
764 case IWN_SDID_1000_8:
765 case IWN_SDID_1000_9:
766 case IWN_SDID_1000_10:
767 case IWN_SDID_1000_11:
768 case IWN_SDID_1000_12:
769 sc->limits = &iwn1000_sensitivity_limits;
770 sc->base_params = &iwn1000_base_params;
771 sc->fwname = "iwn1000fw";
774 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
775 "0x%04x rev %d not supported (subdevice)\n", pid,
776 sc->subdevice_id,sc->hw_type);
785 sc->fwname = "iwn6000fw";
786 sc->limits = &iwn6000_sensitivity_limits;
787 switch(sc->subdevice_id) {
788 case IWN_SDID_6x00_1:
789 case IWN_SDID_6x00_2:
790 case IWN_SDID_6x00_8:
792 sc->base_params = &iwn_6000_base_params;
794 case IWN_SDID_6x00_3:
795 case IWN_SDID_6x00_6:
796 case IWN_SDID_6x00_9:
798 case IWN_SDID_6x00_4:
799 case IWN_SDID_6x00_7:
800 case IWN_SDID_6x00_10:
802 case IWN_SDID_6x00_5:
804 sc->base_params = &iwn_6000i_base_params;
805 sc->sc_flags |= IWN_FLAG_INTERNAL_PA;
806 sc->txchainmask = IWN_ANT_BC;
807 sc->rxchainmask = IWN_ANT_BC;
810 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
811 "0x%04x rev %d not supported (subdevice)\n", pid,
812 sc->subdevice_id,sc->hw_type);
819 switch(sc->subdevice_id) {
820 case IWN_SDID_6x05_1:
821 case IWN_SDID_6x05_4:
822 case IWN_SDID_6x05_6:
824 case IWN_SDID_6x05_2:
825 case IWN_SDID_6x05_5:
826 case IWN_SDID_6x05_7:
828 case IWN_SDID_6x05_3:
830 case IWN_SDID_6x05_8:
831 case IWN_SDID_6x05_9:
832 //iwl6005_2agn_sff_cfg
833 case IWN_SDID_6x05_10:
835 case IWN_SDID_6x05_11:
836 //iwl6005_2agn_mow1_cfg
837 case IWN_SDID_6x05_12:
838 //iwl6005_2agn_mow2_cfg
839 sc->fwname = "iwn6000g2afw";
840 sc->limits = &iwn6000_sensitivity_limits;
841 sc->base_params = &iwn_6000g2_base_params;
844 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
845 "0x%04x rev %d not supported (subdevice)\n", pid,
846 sc->subdevice_id,sc->hw_type);
853 switch(sc->subdevice_id) {
854 case IWN_SDID_6035_1:
855 case IWN_SDID_6035_2:
856 case IWN_SDID_6035_3:
857 case IWN_SDID_6035_4:
858 case IWN_SDID_6035_5:
859 sc->fwname = "iwn6000g2bfw";
860 sc->limits = &iwn6235_sensitivity_limits;
861 sc->base_params = &iwn_6235_base_params;
864 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
865 "0x%04x rev %d not supported (subdevice)\n", pid,
866 sc->subdevice_id,sc->hw_type);
870 /* 6x50 WiFi/WiMax Series */
873 switch(sc->subdevice_id) {
874 case IWN_SDID_6050_1:
875 case IWN_SDID_6050_3:
876 case IWN_SDID_6050_5:
878 case IWN_SDID_6050_2:
879 case IWN_SDID_6050_4:
880 case IWN_SDID_6050_6:
882 sc->fwname = "iwn6050fw";
883 sc->txchainmask = IWN_ANT_AB;
884 sc->rxchainmask = IWN_ANT_AB;
885 sc->limits = &iwn6000_sensitivity_limits;
886 sc->base_params = &iwn_6050_base_params;
889 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
890 "0x%04x rev %d not supported (subdevice)\n", pid,
891 sc->subdevice_id,sc->hw_type);
895 /* 6150 WiFi/WiMax Series */
898 switch(sc->subdevice_id) {
899 case IWN_SDID_6150_1:
900 case IWN_SDID_6150_3:
901 case IWN_SDID_6150_5:
903 case IWN_SDID_6150_2:
904 case IWN_SDID_6150_4:
905 case IWN_SDID_6150_6:
907 sc->fwname = "iwn6050fw";
908 sc->limits = &iwn6000_sensitivity_limits;
909 sc->base_params = &iwn_6150_base_params;
912 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
913 "0x%04x rev %d not supported (subdevice)\n", pid,
914 sc->subdevice_id,sc->hw_type);
918 /* 6030 Series and 1030 Series */
923 switch(sc->subdevice_id) {
924 case IWN_SDID_x030_1:
925 case IWN_SDID_x030_3:
926 case IWN_SDID_x030_5:
928 case IWN_SDID_x030_2:
929 case IWN_SDID_x030_4:
930 case IWN_SDID_x030_6:
932 case IWN_SDID_x030_7:
933 case IWN_SDID_x030_10:
934 case IWN_SDID_x030_14:
936 case IWN_SDID_x030_8:
937 case IWN_SDID_x030_11:
938 case IWN_SDID_x030_15:
940 case IWN_SDID_x030_9:
941 case IWN_SDID_x030_12:
942 case IWN_SDID_x030_16:
944 case IWN_SDID_x030_13:
946 sc->fwname = "iwn6000g2bfw";
947 sc->limits = &iwn6000_sensitivity_limits;
948 sc->base_params = &iwn_6000g2b_base_params;
951 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
952 "0x%04x rev %d not supported (subdevice)\n", pid,
953 sc->subdevice_id,sc->hw_type);
957 /* 130 Series WiFi */
958 /* XXX: This series will need adjustment for rate.
959 * see rx_with_siso_diversity in linux kernel
963 switch(sc->subdevice_id) {
972 sc->fwname = "iwn6000g2bfw";
973 sc->limits = &iwn6000_sensitivity_limits;
974 sc->base_params = &iwn_6000g2b_base_params;
977 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
978 "0x%04x rev %d not supported (subdevice)\n", pid,
979 sc->subdevice_id,sc->hw_type);
983 /* 100 Series WiFi */
986 switch(sc->subdevice_id) {
993 sc->limits = &iwn1000_sensitivity_limits;
994 sc->base_params = &iwn1000_base_params;
995 sc->fwname = "iwn100fw";
998 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
999 "0x%04x rev %d not supported (subdevice)\n", pid,
1000 sc->subdevice_id,sc->hw_type);
1006 /* XXX: This series will need adjustment for rate.
1007 * see rx_with_siso_diversity in linux kernel
1011 switch(sc->subdevice_id) {
1012 case IWN_SDID_105_1:
1013 case IWN_SDID_105_2:
1014 case IWN_SDID_105_3:
1016 case IWN_SDID_105_4:
1018 sc->limits = &iwn2030_sensitivity_limits;
1019 sc->base_params = &iwn2000_base_params;
1020 sc->fwname = "iwn105fw";
1023 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
1024 "0x%04x rev %d not supported (subdevice)\n", pid,
1025 sc->subdevice_id,sc->hw_type);
1031 /* XXX: This series will need adjustment for rate.
1032 * see rx_with_siso_diversity in linux kernel
1036 switch(sc->subdevice_id) {
1037 case IWN_SDID_135_1:
1038 case IWN_SDID_135_2:
1039 case IWN_SDID_135_3:
1040 sc->limits = &iwn2030_sensitivity_limits;
1041 sc->base_params = &iwn2030_base_params;
1042 sc->fwname = "iwn135fw";
1045 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
1046 "0x%04x rev %d not supported (subdevice)\n", pid,
1047 sc->subdevice_id,sc->hw_type);
1053 case IWN_DID_2x00_1:
1054 case IWN_DID_2x00_2:
1055 switch(sc->subdevice_id) {
1056 case IWN_SDID_2x00_1:
1057 case IWN_SDID_2x00_2:
1058 case IWN_SDID_2x00_3:
1060 case IWN_SDID_2x00_4:
1061 //iwl2000_2bgn_d_cfg
1062 sc->limits = &iwn2030_sensitivity_limits;
1063 sc->base_params = &iwn2000_base_params;
1064 sc->fwname = "iwn2000fw";
1067 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
1068 "0x%04x rev %d not supported (subdevice) \n",
1069 pid, sc->subdevice_id, sc->hw_type);
1074 case IWN_DID_2x30_1:
1075 case IWN_DID_2x30_2:
1076 switch(sc->subdevice_id) {
1077 case IWN_SDID_2x30_1:
1078 case IWN_SDID_2x30_3:
1079 case IWN_SDID_2x30_5:
1081 case IWN_SDID_2x30_2:
1082 case IWN_SDID_2x30_4:
1083 case IWN_SDID_2x30_6:
1085 sc->limits = &iwn2030_sensitivity_limits;
1086 sc->base_params = &iwn2030_base_params;
1087 sc->fwname = "iwn2030fw";
1090 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
1091 "0x%04x rev %d not supported (subdevice)\n", pid,
1092 sc->subdevice_id,sc->hw_type);
1097 case IWN_DID_5x00_1:
1098 case IWN_DID_5x00_2:
1099 case IWN_DID_5x00_3:
1100 case IWN_DID_5x00_4:
1101 sc->limits = &iwn5000_sensitivity_limits;
1102 sc->base_params = &iwn5000_base_params;
1103 sc->fwname = "iwn5000fw";
1104 switch(sc->subdevice_id) {
1105 case IWN_SDID_5x00_1:
1106 case IWN_SDID_5x00_2:
1107 case IWN_SDID_5x00_3:
1108 case IWN_SDID_5x00_4:
1109 case IWN_SDID_5x00_9:
1110 case IWN_SDID_5x00_10:
1111 case IWN_SDID_5x00_11:
1112 case IWN_SDID_5x00_12:
1113 case IWN_SDID_5x00_17:
1114 case IWN_SDID_5x00_18:
1115 case IWN_SDID_5x00_19:
1116 case IWN_SDID_5x00_20:
1118 sc->txchainmask = IWN_ANT_B;
1119 sc->rxchainmask = IWN_ANT_AB;
1121 case IWN_SDID_5x00_5:
1122 case IWN_SDID_5x00_6:
1123 case IWN_SDID_5x00_13:
1124 case IWN_SDID_5x00_14:
1125 case IWN_SDID_5x00_21:
1126 case IWN_SDID_5x00_22:
1128 sc->txchainmask = IWN_ANT_B;
1129 sc->rxchainmask = IWN_ANT_AB;
1131 case IWN_SDID_5x00_7:
1132 case IWN_SDID_5x00_8:
1133 case IWN_SDID_5x00_15:
1134 case IWN_SDID_5x00_16:
1135 case IWN_SDID_5x00_23:
1136 case IWN_SDID_5x00_24:
1138 sc->txchainmask = IWN_ANT_B;
1139 sc->rxchainmask = IWN_ANT_AB;
1141 case IWN_SDID_5x00_25:
1142 case IWN_SDID_5x00_26:
1143 case IWN_SDID_5x00_27:
1144 case IWN_SDID_5x00_28:
1145 case IWN_SDID_5x00_29:
1146 case IWN_SDID_5x00_30:
1147 case IWN_SDID_5x00_31:
1148 case IWN_SDID_5x00_32:
1149 case IWN_SDID_5x00_33:
1150 case IWN_SDID_5x00_34:
1151 case IWN_SDID_5x00_35:
1152 case IWN_SDID_5x00_36:
1154 sc->txchainmask = IWN_ANT_ABC;
1155 sc->rxchainmask = IWN_ANT_ABC;
1158 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
1159 "0x%04x rev %d not supported (subdevice)\n", pid,
1160 sc->subdevice_id,sc->hw_type);
1165 case IWN_DID_5x50_1:
1166 case IWN_DID_5x50_2:
1167 case IWN_DID_5x50_3:
1168 case IWN_DID_5x50_4:
1169 sc->limits = &iwn5000_sensitivity_limits;
1170 sc->base_params = &iwn5000_base_params;
1171 sc->fwname = "iwn5000fw";
1172 switch(sc->subdevice_id) {
1173 case IWN_SDID_5x50_1:
1174 case IWN_SDID_5x50_2:
1175 case IWN_SDID_5x50_3:
1177 sc->limits = &iwn5000_sensitivity_limits;
1178 sc->base_params = &iwn5000_base_params;
1179 sc->fwname = "iwn5000fw";
1181 case IWN_SDID_5x50_4:
1182 case IWN_SDID_5x50_5:
1183 case IWN_SDID_5x50_8:
1184 case IWN_SDID_5x50_9:
1185 case IWN_SDID_5x50_10:
1186 case IWN_SDID_5x50_11:
1188 case IWN_SDID_5x50_6:
1189 case IWN_SDID_5x50_7:
1190 case IWN_SDID_5x50_12:
1191 case IWN_SDID_5x50_13:
1193 sc->limits = &iwn5000_sensitivity_limits;
1194 sc->fwname = "iwn5150fw";
1195 sc->base_params = &iwn_5x50_base_params;
1198 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id :"
1199 "0x%04x rev %d not supported (subdevice)\n", pid,
1200 sc->subdevice_id,sc->hw_type);
1205 device_printf(sc->sc_dev, "adapter type id : 0x%04x sub id : 0x%04x"
1206 "rev 0x%08x not supported (device)\n", pid, sc->subdevice_id,
1214 iwn4965_attach(struct iwn_softc *sc, uint16_t pid)
1216 struct iwn_ops *ops = &sc->ops;
1218 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
1220 ops->load_firmware = iwn4965_load_firmware;
1221 ops->read_eeprom = iwn4965_read_eeprom;
1222 ops->post_alive = iwn4965_post_alive;
1223 ops->nic_config = iwn4965_nic_config;
1224 ops->update_sched = iwn4965_update_sched;
1225 ops->get_temperature = iwn4965_get_temperature;
1226 ops->get_rssi = iwn4965_get_rssi;
1227 ops->set_txpower = iwn4965_set_txpower;
1228 ops->init_gains = iwn4965_init_gains;
1229 ops->set_gains = iwn4965_set_gains;
1230 ops->add_node = iwn4965_add_node;
1231 ops->tx_done = iwn4965_tx_done;
1232 ops->ampdu_tx_start = iwn4965_ampdu_tx_start;
1233 ops->ampdu_tx_stop = iwn4965_ampdu_tx_stop;
1234 sc->ntxqs = IWN4965_NTXQUEUES;
1235 sc->firstaggqueue = IWN4965_FIRSTAGGQUEUE;
1236 sc->ndmachnls = IWN4965_NDMACHNLS;
1237 sc->broadcast_id = IWN4965_ID_BROADCAST;
1238 sc->rxonsz = IWN4965_RXONSZ;
1239 sc->schedsz = IWN4965_SCHEDSZ;
1240 sc->fw_text_maxsz = IWN4965_FW_TEXT_MAXSZ;
1241 sc->fw_data_maxsz = IWN4965_FW_DATA_MAXSZ;
1242 sc->fwsz = IWN4965_FWSZ;
1243 sc->sched_txfact_addr = IWN4965_SCHED_TXFACT;
1244 sc->limits = &iwn4965_sensitivity_limits;
1245 sc->fwname = "iwn4965fw";
1246 /* Override chains masks, ROM is known to be broken. */
1247 sc->txchainmask = IWN_ANT_AB;
1248 sc->rxchainmask = IWN_ANT_ABC;
1249 /* Enable normal btcoex */
1250 sc->sc_flags |= IWN_FLAG_BTCOEX;
1252 DPRINTF(sc, IWN_DEBUG_TRACE, "%s: end\n",__func__);
1256 iwn5000_attach(struct iwn_softc *sc, uint16_t pid)
1258 struct iwn_ops *ops = &sc->ops;
1260 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
1262 ops->load_firmware = iwn5000_load_firmware;
1263 ops->read_eeprom = iwn5000_read_eeprom;
1264 ops->post_alive = iwn5000_post_alive;
1265 ops->nic_config = iwn5000_nic_config;
1266 ops->update_sched = iwn5000_update_sched;
1267 ops->get_temperature = iwn5000_get_temperature;
1268 ops->get_rssi = iwn5000_get_rssi;
1269 ops->set_txpower = iwn5000_set_txpower;
1270 ops->init_gains = iwn5000_init_gains;
1271 ops->set_gains = iwn5000_set_gains;
1272 ops->add_node = iwn5000_add_node;
1273 ops->tx_done = iwn5000_tx_done;
1274 ops->ampdu_tx_start = iwn5000_ampdu_tx_start;
1275 ops->ampdu_tx_stop = iwn5000_ampdu_tx_stop;
1276 sc->ntxqs = IWN5000_NTXQUEUES;
1277 sc->firstaggqueue = IWN5000_FIRSTAGGQUEUE;
1278 sc->ndmachnls = IWN5000_NDMACHNLS;
1279 sc->broadcast_id = IWN5000_ID_BROADCAST;
1280 sc->rxonsz = IWN5000_RXONSZ;
1281 sc->schedsz = IWN5000_SCHEDSZ;
1282 sc->fw_text_maxsz = IWN5000_FW_TEXT_MAXSZ;
1283 sc->fw_data_maxsz = IWN5000_FW_DATA_MAXSZ;
1284 sc->fwsz = IWN5000_FWSZ;
1285 sc->sched_txfact_addr = IWN5000_SCHED_TXFACT;
1286 sc->reset_noise_gain = IWN5000_PHY_CALIB_RESET_NOISE_GAIN;
1287 sc->noise_gain = IWN5000_PHY_CALIB_NOISE_GAIN;
1289 DPRINTF(sc, IWN_DEBUG_TRACE, "%s: end\n",__func__);
1293 * Attach the interface to 802.11 radiotap.
1296 iwn_radiotap_attach(struct iwn_softc *sc)
1299 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
1300 ieee80211_radiotap_attach(&sc->sc_ic,
1301 &sc->sc_txtap.wt_ihdr, sizeof(sc->sc_txtap),
1302 IWN_TX_RADIOTAP_PRESENT,
1303 &sc->sc_rxtap.wr_ihdr, sizeof(sc->sc_rxtap),
1304 IWN_RX_RADIOTAP_PRESENT);
1305 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end\n", __func__);
1309 iwn_sysctlattach(struct iwn_softc *sc)
1312 struct sysctl_ctx_list *ctx = device_get_sysctl_ctx(sc->sc_dev);
1313 struct sysctl_oid *tree = device_get_sysctl_tree(sc->sc_dev);
1315 SYSCTL_ADD_INT(ctx, SYSCTL_CHILDREN(tree), OID_AUTO,
1316 "debug", CTLFLAG_RW, &sc->sc_debug, sc->sc_debug,
1317 "control debugging printfs");
1321 static struct ieee80211vap *
1322 iwn_vap_create(struct ieee80211com *ic, const char name[IFNAMSIZ], int unit,
1323 enum ieee80211_opmode opmode, int flags,
1324 const uint8_t bssid[IEEE80211_ADDR_LEN],
1325 const uint8_t mac[IEEE80211_ADDR_LEN])
1327 struct iwn_softc *sc = ic->ic_softc;
1328 struct iwn_vap *ivp;
1329 struct ieee80211vap *vap;
1331 if (!TAILQ_EMPTY(&ic->ic_vaps)) /* only one at a time */
1334 ivp = malloc(sizeof(struct iwn_vap), M_80211_VAP, M_WAITOK | M_ZERO);
1336 ieee80211_vap_setup(ic, vap, name, unit, opmode, flags, bssid);
1337 ivp->ctx = IWN_RXON_BSS_CTX;
1338 vap->iv_bmissthreshold = 10; /* override default */
1339 /* Override with driver methods. */
1340 ivp->iv_newstate = vap->iv_newstate;
1341 vap->iv_newstate = iwn_newstate;
1342 sc->ivap[IWN_RXON_BSS_CTX] = vap;
1344 ieee80211_ratectl_init(vap);
1345 /* Complete setup. */
1346 ieee80211_vap_attach(vap, iwn_media_change, ieee80211_media_status,
1348 ic->ic_opmode = opmode;
1353 iwn_vap_delete(struct ieee80211vap *vap)
1355 struct iwn_vap *ivp = IWN_VAP(vap);
1357 ieee80211_ratectl_deinit(vap);
1358 ieee80211_vap_detach(vap);
1359 free(ivp, M_80211_VAP);
1363 iwn_xmit_queue_drain(struct iwn_softc *sc)
1366 struct ieee80211_node *ni;
1368 IWN_LOCK_ASSERT(sc);
1369 while ((m = mbufq_dequeue(&sc->sc_xmit_queue)) != NULL) {
1370 ni = (struct ieee80211_node *)m->m_pkthdr.rcvif;
1371 ieee80211_free_node(ni);
1377 iwn_xmit_queue_enqueue(struct iwn_softc *sc, struct mbuf *m)
1380 IWN_LOCK_ASSERT(sc);
1381 return (mbufq_enqueue(&sc->sc_xmit_queue, m));
1385 iwn_detach(device_t dev)
1387 struct iwn_softc *sc = device_get_softc(dev);
1390 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
1392 if (sc->sc_ic.ic_softc != NULL) {
1393 /* Free the mbuf queue and node references */
1395 iwn_xmit_queue_drain(sc);
1398 ieee80211_draintask(&sc->sc_ic, &sc->sc_radioon_task);
1399 ieee80211_draintask(&sc->sc_ic, &sc->sc_radiooff_task);
1402 taskqueue_drain_all(sc->sc_tq);
1403 taskqueue_free(sc->sc_tq);
1405 callout_drain(&sc->watchdog_to);
1406 callout_drain(&sc->scan_timeout);
1407 callout_drain(&sc->calib_to);
1408 ieee80211_ifdetach(&sc->sc_ic);
1411 /* Uninstall interrupt handler. */
1412 if (sc->irq != NULL) {
1413 bus_teardown_intr(dev, sc->irq, sc->sc_ih);
1414 bus_release_resource(dev, SYS_RES_IRQ, rman_get_rid(sc->irq),
1416 pci_release_msi(dev);
1419 /* Free DMA resources. */
1420 iwn_free_rx_ring(sc, &sc->rxq);
1421 for (qid = 0; qid < sc->ntxqs; qid++)
1422 iwn_free_tx_ring(sc, &sc->txq[qid]);
1425 if (sc->ict != NULL)
1429 if (sc->mem != NULL)
1430 bus_release_resource(dev, SYS_RES_MEMORY,
1431 rman_get_rid(sc->mem), sc->mem);
1434 destroy_dev(sc->sc_cdev);
1438 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n", __func__);
1439 IWN_LOCK_DESTROY(sc);
1444 iwn_shutdown(device_t dev)
1446 struct iwn_softc *sc = device_get_softc(dev);
1453 iwn_suspend(device_t dev)
1455 struct iwn_softc *sc = device_get_softc(dev);
1457 ieee80211_suspend_all(&sc->sc_ic);
1462 iwn_resume(device_t dev)
1464 struct iwn_softc *sc = device_get_softc(dev);
1466 /* Clear device-specific "PCI retry timeout" register (41h). */
1467 pci_write_config(dev, 0x41, 0, 1);
1469 ieee80211_resume_all(&sc->sc_ic);
1474 iwn_nic_lock(struct iwn_softc *sc)
1478 /* Request exclusive access to NIC. */
1479 IWN_SETBITS(sc, IWN_GP_CNTRL, IWN_GP_CNTRL_MAC_ACCESS_REQ);
1481 /* Spin until we actually get the lock. */
1482 for (ntries = 0; ntries < 1000; ntries++) {
1483 if ((IWN_READ(sc, IWN_GP_CNTRL) &
1484 (IWN_GP_CNTRL_MAC_ACCESS_ENA | IWN_GP_CNTRL_SLEEP)) ==
1485 IWN_GP_CNTRL_MAC_ACCESS_ENA)
1492 static __inline void
1493 iwn_nic_unlock(struct iwn_softc *sc)
1495 IWN_CLRBITS(sc, IWN_GP_CNTRL, IWN_GP_CNTRL_MAC_ACCESS_REQ);
1498 static __inline uint32_t
1499 iwn_prph_read(struct iwn_softc *sc, uint32_t addr)
1501 IWN_WRITE(sc, IWN_PRPH_RADDR, IWN_PRPH_DWORD | addr);
1502 IWN_BARRIER_READ_WRITE(sc);
1503 return IWN_READ(sc, IWN_PRPH_RDATA);
1506 static __inline void
1507 iwn_prph_write(struct iwn_softc *sc, uint32_t addr, uint32_t data)
1509 IWN_WRITE(sc, IWN_PRPH_WADDR, IWN_PRPH_DWORD | addr);
1510 IWN_BARRIER_WRITE(sc);
1511 IWN_WRITE(sc, IWN_PRPH_WDATA, data);
1514 static __inline void
1515 iwn_prph_setbits(struct iwn_softc *sc, uint32_t addr, uint32_t mask)
1517 iwn_prph_write(sc, addr, iwn_prph_read(sc, addr) | mask);
1520 static __inline void
1521 iwn_prph_clrbits(struct iwn_softc *sc, uint32_t addr, uint32_t mask)
1523 iwn_prph_write(sc, addr, iwn_prph_read(sc, addr) & ~mask);
1526 static __inline void
1527 iwn_prph_write_region_4(struct iwn_softc *sc, uint32_t addr,
1528 const uint32_t *data, int count)
1530 for (; count > 0; count--, data++, addr += 4)
1531 iwn_prph_write(sc, addr, *data);
1534 static __inline uint32_t
1535 iwn_mem_read(struct iwn_softc *sc, uint32_t addr)
1537 IWN_WRITE(sc, IWN_MEM_RADDR, addr);
1538 IWN_BARRIER_READ_WRITE(sc);
1539 return IWN_READ(sc, IWN_MEM_RDATA);
1542 static __inline void
1543 iwn_mem_write(struct iwn_softc *sc, uint32_t addr, uint32_t data)
1545 IWN_WRITE(sc, IWN_MEM_WADDR, addr);
1546 IWN_BARRIER_WRITE(sc);
1547 IWN_WRITE(sc, IWN_MEM_WDATA, data);
1550 static __inline void
1551 iwn_mem_write_2(struct iwn_softc *sc, uint32_t addr, uint16_t data)
1555 tmp = iwn_mem_read(sc, addr & ~3);
1557 tmp = (tmp & 0x0000ffff) | data << 16;
1559 tmp = (tmp & 0xffff0000) | data;
1560 iwn_mem_write(sc, addr & ~3, tmp);
1563 static __inline void
1564 iwn_mem_read_region_4(struct iwn_softc *sc, uint32_t addr, uint32_t *data,
1567 for (; count > 0; count--, addr += 4)
1568 *data++ = iwn_mem_read(sc, addr);
1571 static __inline void
1572 iwn_mem_set_region_4(struct iwn_softc *sc, uint32_t addr, uint32_t val,
1575 for (; count > 0; count--, addr += 4)
1576 iwn_mem_write(sc, addr, val);
1580 iwn_eeprom_lock(struct iwn_softc *sc)
1584 for (i = 0; i < 100; i++) {
1585 /* Request exclusive access to EEPROM. */
1586 IWN_SETBITS(sc, IWN_HW_IF_CONFIG,
1587 IWN_HW_IF_CONFIG_EEPROM_LOCKED);
1589 /* Spin until we actually get the lock. */
1590 for (ntries = 0; ntries < 100; ntries++) {
1591 if (IWN_READ(sc, IWN_HW_IF_CONFIG) &
1592 IWN_HW_IF_CONFIG_EEPROM_LOCKED)
1597 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end timeout\n", __func__);
1601 static __inline void
1602 iwn_eeprom_unlock(struct iwn_softc *sc)
1604 IWN_CLRBITS(sc, IWN_HW_IF_CONFIG, IWN_HW_IF_CONFIG_EEPROM_LOCKED);
1608 * Initialize access by host to One Time Programmable ROM.
1609 * NB: This kind of ROM can be found on 1000 or 6000 Series only.
1612 iwn_init_otprom(struct iwn_softc *sc)
1614 uint16_t prev, base, next;
1617 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
1619 /* Wait for clock stabilization before accessing prph. */
1620 if ((error = iwn_clock_wait(sc)) != 0)
1623 if ((error = iwn_nic_lock(sc)) != 0)
1625 iwn_prph_setbits(sc, IWN_APMG_PS, IWN_APMG_PS_RESET_REQ);
1627 iwn_prph_clrbits(sc, IWN_APMG_PS, IWN_APMG_PS_RESET_REQ);
1630 /* Set auto clock gate disable bit for HW with OTP shadow RAM. */
1631 if (sc->base_params->shadow_ram_support) {
1632 IWN_SETBITS(sc, IWN_DBG_LINK_PWR_MGMT,
1633 IWN_RESET_LINK_PWR_MGMT_DIS);
1635 IWN_CLRBITS(sc, IWN_EEPROM_GP, IWN_EEPROM_GP_IF_OWNER);
1636 /* Clear ECC status. */
1637 IWN_SETBITS(sc, IWN_OTP_GP,
1638 IWN_OTP_GP_ECC_CORR_STTS | IWN_OTP_GP_ECC_UNCORR_STTS);
1641 * Find the block before last block (contains the EEPROM image)
1642 * for HW without OTP shadow RAM.
1644 if (! sc->base_params->shadow_ram_support) {
1645 /* Switch to absolute addressing mode. */
1646 IWN_CLRBITS(sc, IWN_OTP_GP, IWN_OTP_GP_RELATIVE_ACCESS);
1648 for (count = 0; count < sc->base_params->max_ll_items;
1650 error = iwn_read_prom_data(sc, base, &next, 2);
1653 if (next == 0) /* End of linked-list. */
1656 base = le16toh(next);
1658 if (count == 0 || count == sc->base_params->max_ll_items)
1660 /* Skip "next" word. */
1661 sc->prom_base = prev + 1;
1664 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end\n", __func__);
1670 iwn_read_prom_data(struct iwn_softc *sc, uint32_t addr, void *data, int count)
1672 uint8_t *out = data;
1676 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
1678 addr += sc->prom_base;
1679 for (; count > 0; count -= 2, addr++) {
1680 IWN_WRITE(sc, IWN_EEPROM, addr << 2);
1681 for (ntries = 0; ntries < 10; ntries++) {
1682 val = IWN_READ(sc, IWN_EEPROM);
1683 if (val & IWN_EEPROM_READ_VALID)
1688 device_printf(sc->sc_dev,
1689 "timeout reading ROM at 0x%x\n", addr);
1692 if (sc->sc_flags & IWN_FLAG_HAS_OTPROM) {
1693 /* OTPROM, check for ECC errors. */
1694 tmp = IWN_READ(sc, IWN_OTP_GP);
1695 if (tmp & IWN_OTP_GP_ECC_UNCORR_STTS) {
1696 device_printf(sc->sc_dev,
1697 "OTPROM ECC error at 0x%x\n", addr);
1700 if (tmp & IWN_OTP_GP_ECC_CORR_STTS) {
1701 /* Correctable ECC error, clear bit. */
1702 IWN_SETBITS(sc, IWN_OTP_GP,
1703 IWN_OTP_GP_ECC_CORR_STTS);
1711 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end\n", __func__);
1717 iwn_dma_map_addr(void *arg, bus_dma_segment_t *segs, int nsegs, int error)
1721 KASSERT(nsegs == 1, ("too many DMA segments, %d should be 1", nsegs));
1722 *(bus_addr_t *)arg = segs[0].ds_addr;
1726 iwn_dma_contig_alloc(struct iwn_softc *sc, struct iwn_dma_info *dma,
1727 void **kvap, bus_size_t size, bus_size_t alignment)
1734 error = bus_dma_tag_create(bus_get_dma_tag(sc->sc_dev), alignment,
1735 0, BUS_SPACE_MAXADDR_32BIT, BUS_SPACE_MAXADDR, NULL, NULL, size,
1736 1, size, 0, NULL, NULL, &dma->tag);
1740 error = bus_dmamem_alloc(dma->tag, (void **)&dma->vaddr,
1741 BUS_DMA_NOWAIT | BUS_DMA_ZERO | BUS_DMA_COHERENT, &dma->map);
1745 error = bus_dmamap_load(dma->tag, dma->map, dma->vaddr, size,
1746 iwn_dma_map_addr, &dma->paddr, BUS_DMA_NOWAIT);
1750 bus_dmamap_sync(dma->tag, dma->map, BUS_DMASYNC_PREWRITE);
1757 fail: iwn_dma_contig_free(dma);
1762 iwn_dma_contig_free(struct iwn_dma_info *dma)
1764 if (dma->vaddr != NULL) {
1765 bus_dmamap_sync(dma->tag, dma->map,
1766 BUS_DMASYNC_POSTREAD | BUS_DMASYNC_POSTWRITE);
1767 bus_dmamap_unload(dma->tag, dma->map);
1768 bus_dmamem_free(dma->tag, dma->vaddr, dma->map);
1771 if (dma->tag != NULL) {
1772 bus_dma_tag_destroy(dma->tag);
1778 iwn_alloc_sched(struct iwn_softc *sc)
1780 /* TX scheduler rings must be aligned on a 1KB boundary. */
1781 return iwn_dma_contig_alloc(sc, &sc->sched_dma, (void **)&sc->sched,
1786 iwn_free_sched(struct iwn_softc *sc)
1788 iwn_dma_contig_free(&sc->sched_dma);
1792 iwn_alloc_kw(struct iwn_softc *sc)
1794 /* "Keep Warm" page must be aligned on a 4KB boundary. */
1795 return iwn_dma_contig_alloc(sc, &sc->kw_dma, NULL, 4096, 4096);
1799 iwn_free_kw(struct iwn_softc *sc)
1801 iwn_dma_contig_free(&sc->kw_dma);
1805 iwn_alloc_ict(struct iwn_softc *sc)
1807 /* ICT table must be aligned on a 4KB boundary. */
1808 return iwn_dma_contig_alloc(sc, &sc->ict_dma, (void **)&sc->ict,
1809 IWN_ICT_SIZE, 4096);
1813 iwn_free_ict(struct iwn_softc *sc)
1815 iwn_dma_contig_free(&sc->ict_dma);
1819 iwn_alloc_fwmem(struct iwn_softc *sc)
1821 /* Must be aligned on a 16-byte boundary. */
1822 return iwn_dma_contig_alloc(sc, &sc->fw_dma, NULL, sc->fwsz, 16);
1826 iwn_free_fwmem(struct iwn_softc *sc)
1828 iwn_dma_contig_free(&sc->fw_dma);
1832 iwn_alloc_rx_ring(struct iwn_softc *sc, struct iwn_rx_ring *ring)
1839 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
1841 /* Allocate RX descriptors (256-byte aligned). */
1842 size = IWN_RX_RING_COUNT * sizeof (uint32_t);
1843 error = iwn_dma_contig_alloc(sc, &ring->desc_dma, (void **)&ring->desc,
1846 device_printf(sc->sc_dev,
1847 "%s: could not allocate RX ring DMA memory, error %d\n",
1852 /* Allocate RX status area (16-byte aligned). */
1853 error = iwn_dma_contig_alloc(sc, &ring->stat_dma, (void **)&ring->stat,
1854 sizeof (struct iwn_rx_status), 16);
1856 device_printf(sc->sc_dev,
1857 "%s: could not allocate RX status DMA memory, error %d\n",
1862 /* Create RX buffer DMA tag. */
1863 error = bus_dma_tag_create(bus_get_dma_tag(sc->sc_dev), 1, 0,
1864 BUS_SPACE_MAXADDR_32BIT, BUS_SPACE_MAXADDR, NULL, NULL,
1865 IWN_RBUF_SIZE, 1, IWN_RBUF_SIZE, 0, NULL, NULL, &ring->data_dmat);
1867 device_printf(sc->sc_dev,
1868 "%s: could not create RX buf DMA tag, error %d\n",
1874 * Allocate and map RX buffers.
1876 for (i = 0; i < IWN_RX_RING_COUNT; i++) {
1877 struct iwn_rx_data *data = &ring->data[i];
1880 error = bus_dmamap_create(ring->data_dmat, 0, &data->map);
1882 device_printf(sc->sc_dev,
1883 "%s: could not create RX buf DMA map, error %d\n",
1888 data->m = m_getjcl(M_NOWAIT, MT_DATA, M_PKTHDR,
1890 if (data->m == NULL) {
1891 device_printf(sc->sc_dev,
1892 "%s: could not allocate RX mbuf\n", __func__);
1897 error = bus_dmamap_load(ring->data_dmat, data->map,
1898 mtod(data->m, void *), IWN_RBUF_SIZE, iwn_dma_map_addr,
1899 &paddr, BUS_DMA_NOWAIT);
1900 if (error != 0 && error != EFBIG) {
1901 device_printf(sc->sc_dev,
1902 "%s: can't map mbuf, error %d\n", __func__,
1907 bus_dmamap_sync(ring->data_dmat, data->map,
1908 BUS_DMASYNC_PREREAD);
1910 /* Set physical address of RX buffer (256-byte aligned). */
1911 ring->desc[i] = htole32(paddr >> 8);
1914 bus_dmamap_sync(ring->desc_dma.tag, ring->desc_dma.map,
1915 BUS_DMASYNC_PREWRITE);
1917 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
1921 fail: iwn_free_rx_ring(sc, ring);
1923 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end in error\n",__func__);
1929 iwn_reset_rx_ring(struct iwn_softc *sc, struct iwn_rx_ring *ring)
1933 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
1935 if (iwn_nic_lock(sc) == 0) {
1936 IWN_WRITE(sc, IWN_FH_RX_CONFIG, 0);
1937 for (ntries = 0; ntries < 1000; ntries++) {
1938 if (IWN_READ(sc, IWN_FH_RX_STATUS) &
1939 IWN_FH_RX_STATUS_IDLE)
1946 sc->last_rx_valid = 0;
1950 iwn_free_rx_ring(struct iwn_softc *sc, struct iwn_rx_ring *ring)
1954 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s \n", __func__);
1956 iwn_dma_contig_free(&ring->desc_dma);
1957 iwn_dma_contig_free(&ring->stat_dma);
1959 for (i = 0; i < IWN_RX_RING_COUNT; i++) {
1960 struct iwn_rx_data *data = &ring->data[i];
1962 if (data->m != NULL) {
1963 bus_dmamap_sync(ring->data_dmat, data->map,
1964 BUS_DMASYNC_POSTREAD);
1965 bus_dmamap_unload(ring->data_dmat, data->map);
1969 if (data->map != NULL)
1970 bus_dmamap_destroy(ring->data_dmat, data->map);
1972 if (ring->data_dmat != NULL) {
1973 bus_dma_tag_destroy(ring->data_dmat);
1974 ring->data_dmat = NULL;
1979 iwn_alloc_tx_ring(struct iwn_softc *sc, struct iwn_tx_ring *ring, int qid)
1989 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
1991 /* Allocate TX descriptors (256-byte aligned). */
1992 size = IWN_TX_RING_COUNT * sizeof (struct iwn_tx_desc);
1993 error = iwn_dma_contig_alloc(sc, &ring->desc_dma, (void **)&ring->desc,
1996 device_printf(sc->sc_dev,
1997 "%s: could not allocate TX ring DMA memory, error %d\n",
2002 size = IWN_TX_RING_COUNT * sizeof (struct iwn_tx_cmd);
2003 error = iwn_dma_contig_alloc(sc, &ring->cmd_dma, (void **)&ring->cmd,
2006 device_printf(sc->sc_dev,
2007 "%s: could not allocate TX cmd DMA memory, error %d\n",
2012 error = bus_dma_tag_create(bus_get_dma_tag(sc->sc_dev), 1, 0,
2013 BUS_SPACE_MAXADDR_32BIT, BUS_SPACE_MAXADDR, NULL, NULL, MCLBYTES,
2014 IWN_MAX_SCATTER - 1, MCLBYTES, 0, NULL, NULL, &ring->data_dmat);
2016 device_printf(sc->sc_dev,
2017 "%s: could not create TX buf DMA tag, error %d\n",
2022 paddr = ring->cmd_dma.paddr;
2023 for (i = 0; i < IWN_TX_RING_COUNT; i++) {
2024 struct iwn_tx_data *data = &ring->data[i];
2026 data->cmd_paddr = paddr;
2027 data->scratch_paddr = paddr + 12;
2028 paddr += sizeof (struct iwn_tx_cmd);
2030 error = bus_dmamap_create(ring->data_dmat, 0, &data->map);
2032 device_printf(sc->sc_dev,
2033 "%s: could not create TX buf DMA map, error %d\n",
2039 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end\n", __func__);
2043 fail: iwn_free_tx_ring(sc, ring);
2044 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end in error\n", __func__);
2049 iwn_reset_tx_ring(struct iwn_softc *sc, struct iwn_tx_ring *ring)
2053 DPRINTF(sc, IWN_DEBUG_TRACE, "->doing %s \n", __func__);
2055 for (i = 0; i < IWN_TX_RING_COUNT; i++) {
2056 struct iwn_tx_data *data = &ring->data[i];
2058 if (data->m != NULL) {
2059 bus_dmamap_sync(ring->data_dmat, data->map,
2060 BUS_DMASYNC_POSTWRITE);
2061 bus_dmamap_unload(ring->data_dmat, data->map);
2065 if (data->ni != NULL) {
2066 ieee80211_free_node(data->ni);
2070 /* Clear TX descriptors. */
2071 memset(ring->desc, 0, ring->desc_dma.size);
2072 bus_dmamap_sync(ring->desc_dma.tag, ring->desc_dma.map,
2073 BUS_DMASYNC_PREWRITE);
2074 sc->qfullmsk &= ~(1 << ring->qid);
2080 iwn_free_tx_ring(struct iwn_softc *sc, struct iwn_tx_ring *ring)
2084 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s \n", __func__);
2086 iwn_dma_contig_free(&ring->desc_dma);
2087 iwn_dma_contig_free(&ring->cmd_dma);
2089 for (i = 0; i < IWN_TX_RING_COUNT; i++) {
2090 struct iwn_tx_data *data = &ring->data[i];
2092 if (data->m != NULL) {
2093 bus_dmamap_sync(ring->data_dmat, data->map,
2094 BUS_DMASYNC_POSTWRITE);
2095 bus_dmamap_unload(ring->data_dmat, data->map);
2098 if (data->map != NULL)
2099 bus_dmamap_destroy(ring->data_dmat, data->map);
2101 if (ring->data_dmat != NULL) {
2102 bus_dma_tag_destroy(ring->data_dmat);
2103 ring->data_dmat = NULL;
2108 iwn5000_ict_reset(struct iwn_softc *sc)
2110 /* Disable interrupts. */
2111 IWN_WRITE(sc, IWN_INT_MASK, 0);
2113 /* Reset ICT table. */
2114 memset(sc->ict, 0, IWN_ICT_SIZE);
2117 bus_dmamap_sync(sc->ict_dma.tag, sc->ict_dma.map,
2118 BUS_DMASYNC_PREWRITE);
2120 /* Set physical address of ICT table (4KB aligned). */
2121 DPRINTF(sc, IWN_DEBUG_RESET, "%s: enabling ICT\n", __func__);
2122 IWN_WRITE(sc, IWN_DRAM_INT_TBL, IWN_DRAM_INT_TBL_ENABLE |
2123 IWN_DRAM_INT_TBL_WRAP_CHECK | sc->ict_dma.paddr >> 12);
2125 /* Enable periodic RX interrupt. */
2126 sc->int_mask |= IWN_INT_RX_PERIODIC;
2127 /* Switch to ICT interrupt mode in driver. */
2128 sc->sc_flags |= IWN_FLAG_USE_ICT;
2130 /* Re-enable interrupts. */
2131 IWN_WRITE(sc, IWN_INT, 0xffffffff);
2132 IWN_WRITE(sc, IWN_INT_MASK, sc->int_mask);
2136 iwn_read_eeprom(struct iwn_softc *sc, uint8_t macaddr[IEEE80211_ADDR_LEN])
2138 struct iwn_ops *ops = &sc->ops;
2142 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
2144 /* Check whether adapter has an EEPROM or an OTPROM. */
2145 if (sc->hw_type >= IWN_HW_REV_TYPE_1000 &&
2146 (IWN_READ(sc, IWN_OTP_GP) & IWN_OTP_GP_DEV_SEL_OTP))
2147 sc->sc_flags |= IWN_FLAG_HAS_OTPROM;
2148 DPRINTF(sc, IWN_DEBUG_RESET, "%s found\n",
2149 (sc->sc_flags & IWN_FLAG_HAS_OTPROM) ? "OTPROM" : "EEPROM");
2151 /* Adapter has to be powered on for EEPROM access to work. */
2152 if ((error = iwn_apm_init(sc)) != 0) {
2153 device_printf(sc->sc_dev,
2154 "%s: could not power ON adapter, error %d\n", __func__,
2159 if ((IWN_READ(sc, IWN_EEPROM_GP) & 0x7) == 0) {
2160 device_printf(sc->sc_dev, "%s: bad ROM signature\n", __func__);
2163 if ((error = iwn_eeprom_lock(sc)) != 0) {
2164 device_printf(sc->sc_dev, "%s: could not lock ROM, error %d\n",
2168 if (sc->sc_flags & IWN_FLAG_HAS_OTPROM) {
2169 if ((error = iwn_init_otprom(sc)) != 0) {
2170 device_printf(sc->sc_dev,
2171 "%s: could not initialize OTPROM, error %d\n",
2177 iwn_read_prom_data(sc, IWN_EEPROM_SKU_CAP, &val, 2);
2178 DPRINTF(sc, IWN_DEBUG_RESET, "SKU capabilities=0x%04x\n", le16toh(val));
2179 /* Check if HT support is bonded out. */
2180 if (val & htole16(IWN_EEPROM_SKU_CAP_11N))
2181 sc->sc_flags |= IWN_FLAG_HAS_11N;
2183 iwn_read_prom_data(sc, IWN_EEPROM_RFCFG, &val, 2);
2184 sc->rfcfg = le16toh(val);
2185 DPRINTF(sc, IWN_DEBUG_RESET, "radio config=0x%04x\n", sc->rfcfg);
2186 /* Read Tx/Rx chains from ROM unless it's known to be broken. */
2187 if (sc->txchainmask == 0)
2188 sc->txchainmask = IWN_RFCFG_TXANTMSK(sc->rfcfg);
2189 if (sc->rxchainmask == 0)
2190 sc->rxchainmask = IWN_RFCFG_RXANTMSK(sc->rfcfg);
2192 /* Read MAC address. */
2193 iwn_read_prom_data(sc, IWN_EEPROM_MAC, macaddr, 6);
2195 /* Read adapter-specific information from EEPROM. */
2196 ops->read_eeprom(sc);
2198 iwn_apm_stop(sc); /* Power OFF adapter. */
2200 iwn_eeprom_unlock(sc);
2202 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end\n", __func__);
2208 iwn4965_read_eeprom(struct iwn_softc *sc)
2214 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
2216 /* Read regulatory domain (4 ASCII characters). */
2217 iwn_read_prom_data(sc, IWN4965_EEPROM_DOMAIN, sc->eeprom_domain, 4);
2219 /* Read the list of authorized channels (20MHz & 40MHz). */
2220 for (i = 0; i < IWN_NBANDS - 1; i++) {
2221 addr = iwn4965_regulatory_bands[i];
2222 iwn_read_eeprom_channels(sc, i, addr);
2225 /* Read maximum allowed TX power for 2GHz and 5GHz bands. */
2226 iwn_read_prom_data(sc, IWN4965_EEPROM_MAXPOW, &val, 2);
2227 sc->maxpwr2GHz = val & 0xff;
2228 sc->maxpwr5GHz = val >> 8;
2229 /* Check that EEPROM values are within valid range. */
2230 if (sc->maxpwr5GHz < 20 || sc->maxpwr5GHz > 50)
2231 sc->maxpwr5GHz = 38;
2232 if (sc->maxpwr2GHz < 20 || sc->maxpwr2GHz > 50)
2233 sc->maxpwr2GHz = 38;
2234 DPRINTF(sc, IWN_DEBUG_RESET, "maxpwr 2GHz=%d 5GHz=%d\n",
2235 sc->maxpwr2GHz, sc->maxpwr5GHz);
2237 /* Read samples for each TX power group. */
2238 iwn_read_prom_data(sc, IWN4965_EEPROM_BANDS, sc->bands,
2241 /* Read voltage at which samples were taken. */
2242 iwn_read_prom_data(sc, IWN4965_EEPROM_VOLTAGE, &val, 2);
2243 sc->eeprom_voltage = (int16_t)le16toh(val);
2244 DPRINTF(sc, IWN_DEBUG_RESET, "voltage=%d (in 0.3V)\n",
2245 sc->eeprom_voltage);
2248 /* Print samples. */
2249 if (sc->sc_debug & IWN_DEBUG_ANY) {
2250 for (i = 0; i < IWN_NBANDS - 1; i++)
2251 iwn4965_print_power_group(sc, i);
2255 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end\n", __func__);
2260 iwn4965_print_power_group(struct iwn_softc *sc, int i)
2262 struct iwn4965_eeprom_band *band = &sc->bands[i];
2263 struct iwn4965_eeprom_chan_samples *chans = band->chans;
2266 printf("===band %d===\n", i);
2267 printf("chan lo=%d, chan hi=%d\n", band->lo, band->hi);
2268 printf("chan1 num=%d\n", chans[0].num);
2269 for (c = 0; c < 2; c++) {
2270 for (j = 0; j < IWN_NSAMPLES; j++) {
2271 printf("chain %d, sample %d: temp=%d gain=%d "
2272 "power=%d pa_det=%d\n", c, j,
2273 chans[0].samples[c][j].temp,
2274 chans[0].samples[c][j].gain,
2275 chans[0].samples[c][j].power,
2276 chans[0].samples[c][j].pa_det);
2279 printf("chan2 num=%d\n", chans[1].num);
2280 for (c = 0; c < 2; c++) {
2281 for (j = 0; j < IWN_NSAMPLES; j++) {
2282 printf("chain %d, sample %d: temp=%d gain=%d "
2283 "power=%d pa_det=%d\n", c, j,
2284 chans[1].samples[c][j].temp,
2285 chans[1].samples[c][j].gain,
2286 chans[1].samples[c][j].power,
2287 chans[1].samples[c][j].pa_det);
2294 iwn5000_read_eeprom(struct iwn_softc *sc)
2296 struct iwn5000_eeprom_calib_hdr hdr;
2298 uint32_t base, addr;
2302 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
2304 /* Read regulatory domain (4 ASCII characters). */
2305 iwn_read_prom_data(sc, IWN5000_EEPROM_REG, &val, 2);
2306 base = le16toh(val);
2307 iwn_read_prom_data(sc, base + IWN5000_EEPROM_DOMAIN,
2308 sc->eeprom_domain, 4);
2310 /* Read the list of authorized channels (20MHz & 40MHz). */
2311 for (i = 0; i < IWN_NBANDS - 1; i++) {
2312 addr = base + sc->base_params->regulatory_bands[i];
2313 iwn_read_eeprom_channels(sc, i, addr);
2316 /* Read enhanced TX power information for 6000 Series. */
2317 if (sc->base_params->enhanced_TX_power)
2318 iwn_read_eeprom_enhinfo(sc);
2320 iwn_read_prom_data(sc, IWN5000_EEPROM_CAL, &val, 2);
2321 base = le16toh(val);
2322 iwn_read_prom_data(sc, base, &hdr, sizeof hdr);
2323 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
2324 "%s: calib version=%u pa type=%u voltage=%u\n", __func__,
2325 hdr.version, hdr.pa_type, le16toh(hdr.volt));
2326 sc->calib_ver = hdr.version;
2328 if (sc->base_params->calib_need & IWN_FLG_NEED_PHY_CALIB_TEMP_OFFSETv2) {
2329 sc->eeprom_voltage = le16toh(hdr.volt);
2330 iwn_read_prom_data(sc, base + IWN5000_EEPROM_TEMP, &val, 2);
2331 sc->eeprom_temp_high=le16toh(val);
2332 iwn_read_prom_data(sc, base + IWN5000_EEPROM_VOLT, &val, 2);
2333 sc->eeprom_temp = le16toh(val);
2336 if (sc->hw_type == IWN_HW_REV_TYPE_5150) {
2337 /* Compute temperature offset. */
2338 iwn_read_prom_data(sc, base + IWN5000_EEPROM_TEMP, &val, 2);
2339 sc->eeprom_temp = le16toh(val);
2340 iwn_read_prom_data(sc, base + IWN5000_EEPROM_VOLT, &val, 2);
2341 volt = le16toh(val);
2342 sc->temp_off = sc->eeprom_temp - (volt / -5);
2343 DPRINTF(sc, IWN_DEBUG_CALIBRATE, "temp=%d volt=%d offset=%dK\n",
2344 sc->eeprom_temp, volt, sc->temp_off);
2346 /* Read crystal calibration. */
2347 iwn_read_prom_data(sc, base + IWN5000_EEPROM_CRYSTAL,
2348 &sc->eeprom_crystal, sizeof (uint32_t));
2349 DPRINTF(sc, IWN_DEBUG_CALIBRATE, "crystal calibration 0x%08x\n",
2350 le32toh(sc->eeprom_crystal));
2353 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end\n", __func__);
2358 * Translate EEPROM flags to net80211.
2361 iwn_eeprom_channel_flags(struct iwn_eeprom_chan *channel)
2366 if ((channel->flags & IWN_EEPROM_CHAN_ACTIVE) == 0)
2367 nflags |= IEEE80211_CHAN_PASSIVE;
2368 if ((channel->flags & IWN_EEPROM_CHAN_IBSS) == 0)
2369 nflags |= IEEE80211_CHAN_NOADHOC;
2370 if (channel->flags & IWN_EEPROM_CHAN_RADAR) {
2371 nflags |= IEEE80211_CHAN_DFS;
2372 /* XXX apparently IBSS may still be marked */
2373 nflags |= IEEE80211_CHAN_NOADHOC;
2380 iwn_read_eeprom_band(struct iwn_softc *sc, int n, int maxchans, int *nchans,
2381 struct ieee80211_channel chans[])
2383 struct iwn_eeprom_chan *channels = sc->eeprom_channels[n];
2384 const struct iwn_chan_band *band = &iwn_bands[n];
2385 uint8_t bands[IEEE80211_MODE_BYTES];
2387 int i, error, nflags;
2389 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
2391 memset(bands, 0, sizeof(bands));
2393 setbit(bands, IEEE80211_MODE_11B);
2394 setbit(bands, IEEE80211_MODE_11G);
2395 if (sc->sc_flags & IWN_FLAG_HAS_11N)
2396 setbit(bands, IEEE80211_MODE_11NG);
2398 setbit(bands, IEEE80211_MODE_11A);
2399 if (sc->sc_flags & IWN_FLAG_HAS_11N)
2400 setbit(bands, IEEE80211_MODE_11NA);
2403 for (i = 0; i < band->nchan; i++) {
2404 if (!(channels[i].flags & IWN_EEPROM_CHAN_VALID)) {
2405 DPRINTF(sc, IWN_DEBUG_RESET,
2406 "skip chan %d flags 0x%x maxpwr %d\n",
2407 band->chan[i], channels[i].flags,
2408 channels[i].maxpwr);
2412 chan = band->chan[i];
2413 nflags = iwn_eeprom_channel_flags(&channels[i]);
2414 error = ieee80211_add_channel(chans, maxchans, nchans,
2415 chan, 0, channels[i].maxpwr, nflags, bands);
2419 /* Save maximum allowed TX power for this channel. */
2421 sc->maxpwr[chan] = channels[i].maxpwr;
2423 DPRINTF(sc, IWN_DEBUG_RESET,
2424 "add chan %d flags 0x%x maxpwr %d\n", chan,
2425 channels[i].flags, channels[i].maxpwr);
2428 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end\n", __func__);
2433 iwn_read_eeprom_ht40(struct iwn_softc *sc, int n, int maxchans, int *nchans,
2434 struct ieee80211_channel chans[])
2436 struct iwn_eeprom_chan *channels = sc->eeprom_channels[n];
2437 const struct iwn_chan_band *band = &iwn_bands[n];
2439 int i, error, nflags;
2441 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s start\n", __func__);
2443 if (!(sc->sc_flags & IWN_FLAG_HAS_11N)) {
2444 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end no 11n\n", __func__);
2448 for (i = 0; i < band->nchan; i++) {
2449 if (!(channels[i].flags & IWN_EEPROM_CHAN_VALID)) {
2450 DPRINTF(sc, IWN_DEBUG_RESET,
2451 "skip chan %d flags 0x%x maxpwr %d\n",
2452 band->chan[i], channels[i].flags,
2453 channels[i].maxpwr);
2457 chan = band->chan[i];
2458 nflags = iwn_eeprom_channel_flags(&channels[i]);
2459 nflags |= (n == 5 ? IEEE80211_CHAN_G : IEEE80211_CHAN_A);
2460 error = ieee80211_add_channel_ht40(chans, maxchans, nchans,
2461 chan, channels[i].maxpwr, nflags);
2464 device_printf(sc->sc_dev,
2465 "%s: no entry for channel %d\n", __func__, chan);
2468 DPRINTF(sc, IWN_DEBUG_RESET,
2469 "%s: skip chan %d, extension channel not found\n",
2473 device_printf(sc->sc_dev,
2474 "%s: channel table is full!\n", __func__);
2477 DPRINTF(sc, IWN_DEBUG_RESET,
2478 "add ht40 chan %d flags 0x%x maxpwr %d\n",
2479 chan, channels[i].flags, channels[i].maxpwr);
2486 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end\n", __func__);
2491 iwn_read_eeprom_channels(struct iwn_softc *sc, int n, uint32_t addr)
2493 struct ieee80211com *ic = &sc->sc_ic;
2495 iwn_read_prom_data(sc, addr, &sc->eeprom_channels[n],
2496 iwn_bands[n].nchan * sizeof (struct iwn_eeprom_chan));
2499 iwn_read_eeprom_band(sc, n, IEEE80211_CHAN_MAX, &ic->ic_nchans,
2502 iwn_read_eeprom_ht40(sc, n, IEEE80211_CHAN_MAX, &ic->ic_nchans,
2505 ieee80211_sort_channels(ic->ic_channels, ic->ic_nchans);
2508 static struct iwn_eeprom_chan *
2509 iwn_find_eeprom_channel(struct iwn_softc *sc, struct ieee80211_channel *c)
2511 int band, chan, i, j;
2513 if (IEEE80211_IS_CHAN_HT40(c)) {
2514 band = IEEE80211_IS_CHAN_5GHZ(c) ? 6 : 5;
2515 if (IEEE80211_IS_CHAN_HT40D(c))
2516 chan = c->ic_extieee;
2519 for (i = 0; i < iwn_bands[band].nchan; i++) {
2520 if (iwn_bands[band].chan[i] == chan)
2521 return &sc->eeprom_channels[band][i];
2524 for (j = 0; j < 5; j++) {
2525 for (i = 0; i < iwn_bands[j].nchan; i++) {
2526 if (iwn_bands[j].chan[i] == c->ic_ieee &&
2527 ((j == 0) ^ IEEE80211_IS_CHAN_A(c)) == 1)
2528 return &sc->eeprom_channels[j][i];
2536 iwn_getradiocaps(struct ieee80211com *ic,
2537 int maxchans, int *nchans, struct ieee80211_channel chans[])
2539 struct iwn_softc *sc = ic->ic_softc;
2542 /* Parse the list of authorized channels. */
2543 for (i = 0; i < 5 && *nchans < maxchans; i++)
2544 iwn_read_eeprom_band(sc, i, maxchans, nchans, chans);
2545 for (i = 5; i < IWN_NBANDS - 1 && *nchans < maxchans; i++)
2546 iwn_read_eeprom_ht40(sc, i, maxchans, nchans, chans);
2550 * Enforce flags read from EEPROM.
2553 iwn_setregdomain(struct ieee80211com *ic, struct ieee80211_regdomain *rd,
2554 int nchan, struct ieee80211_channel chans[])
2556 struct iwn_softc *sc = ic->ic_softc;
2559 for (i = 0; i < nchan; i++) {
2560 struct ieee80211_channel *c = &chans[i];
2561 struct iwn_eeprom_chan *channel;
2563 channel = iwn_find_eeprom_channel(sc, c);
2564 if (channel == NULL) {
2565 ic_printf(ic, "%s: invalid channel %u freq %u/0x%x\n",
2566 __func__, c->ic_ieee, c->ic_freq, c->ic_flags);
2569 c->ic_flags |= iwn_eeprom_channel_flags(channel);
2576 iwn_read_eeprom_enhinfo(struct iwn_softc *sc)
2578 struct iwn_eeprom_enhinfo enhinfo[35];
2579 struct ieee80211com *ic = &sc->sc_ic;
2580 struct ieee80211_channel *c;
2586 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
2588 iwn_read_prom_data(sc, IWN5000_EEPROM_REG, &val, 2);
2589 base = le16toh(val);
2590 iwn_read_prom_data(sc, base + IWN6000_EEPROM_ENHINFO,
2591 enhinfo, sizeof enhinfo);
2593 for (i = 0; i < nitems(enhinfo); i++) {
2594 flags = enhinfo[i].flags;
2595 if (!(flags & IWN_ENHINFO_VALID))
2596 continue; /* Skip invalid entries. */
2599 if (sc->txchainmask & IWN_ANT_A)
2600 maxpwr = MAX(maxpwr, enhinfo[i].chain[0]);
2601 if (sc->txchainmask & IWN_ANT_B)
2602 maxpwr = MAX(maxpwr, enhinfo[i].chain[1]);
2603 if (sc->txchainmask & IWN_ANT_C)
2604 maxpwr = MAX(maxpwr, enhinfo[i].chain[2]);
2605 if (sc->ntxchains == 2)
2606 maxpwr = MAX(maxpwr, enhinfo[i].mimo2);
2607 else if (sc->ntxchains == 3)
2608 maxpwr = MAX(maxpwr, enhinfo[i].mimo3);
2610 for (j = 0; j < ic->ic_nchans; j++) {
2611 c = &ic->ic_channels[j];
2612 if ((flags & IWN_ENHINFO_5GHZ)) {
2613 if (!IEEE80211_IS_CHAN_A(c))
2615 } else if ((flags & IWN_ENHINFO_OFDM)) {
2616 if (!IEEE80211_IS_CHAN_G(c))
2618 } else if (!IEEE80211_IS_CHAN_B(c))
2620 if ((flags & IWN_ENHINFO_HT40)) {
2621 if (!IEEE80211_IS_CHAN_HT40(c))
2624 if (IEEE80211_IS_CHAN_HT40(c))
2627 if (enhinfo[i].chan != 0 &&
2628 enhinfo[i].chan != c->ic_ieee)
2631 DPRINTF(sc, IWN_DEBUG_RESET,
2632 "channel %d(%x), maxpwr %d\n", c->ic_ieee,
2633 c->ic_flags, maxpwr / 2);
2634 c->ic_maxregpower = maxpwr / 2;
2635 c->ic_maxpower = maxpwr;
2639 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end\n", __func__);
2643 static struct ieee80211_node *
2644 iwn_node_alloc(struct ieee80211vap *vap, const uint8_t mac[IEEE80211_ADDR_LEN])
2646 return malloc(sizeof (struct iwn_node), M_80211_NODE,M_NOWAIT | M_ZERO);
2652 switch (rate & 0xff) {
2653 case 12: return 0xd;
2654 case 18: return 0xf;
2655 case 24: return 0x5;
2656 case 36: return 0x7;
2657 case 48: return 0x9;
2658 case 72: return 0xb;
2659 case 96: return 0x1;
2660 case 108: return 0x3;
2664 case 22: return 110;
2670 iwn_get_1stream_tx_antmask(struct iwn_softc *sc)
2673 return IWN_LSB(sc->txchainmask);
2677 iwn_get_2stream_tx_antmask(struct iwn_softc *sc)
2682 * The '2 stream' setup is a bit .. odd.
2684 * For NICs that support only 1 antenna, default to IWN_ANT_AB or
2685 * the firmware panics (eg Intel 5100.)
2687 * For NICs that support two antennas, we use ANT_AB.
2689 * For NICs that support three antennas, we use the two that
2690 * wasn't the default one.
2692 * XXX TODO: if bluetooth (full concurrent) is enabled, restrict
2693 * this to only one antenna.
2696 /* Default - transmit on the other antennas */
2697 tx = (sc->txchainmask & ~IWN_LSB(sc->txchainmask));
2699 /* Now, if it's zero, set it to IWN_ANT_AB, so to not panic firmware */
2704 * If the NIC is a two-stream TX NIC, configure the TX mask to
2705 * the default chainmask
2707 else if (sc->ntxchains == 2)
2708 tx = sc->txchainmask;
2716 * Calculate the required PLCP value from the given rate,
2717 * to the given node.
2719 * This will take the node configuration (eg 11n, rate table
2720 * setup, etc) into consideration.
2723 iwn_rate_to_plcp(struct iwn_softc *sc, struct ieee80211_node *ni,
2726 struct ieee80211com *ic = ni->ni_ic;
2731 * If it's an MCS rate, let's set the plcp correctly
2732 * and set the relevant flags based on the node config.
2734 if (rate & IEEE80211_RATE_MCS) {
2736 * Set the initial PLCP value to be between 0->31 for
2737 * MCS 0 -> MCS 31, then set the "I'm an MCS rate!"
2740 plcp = IEEE80211_RV(rate) | IWN_RFLAG_MCS;
2743 * XXX the following should only occur if both
2744 * the local configuration _and_ the remote node
2745 * advertise these capabilities. Thus this code
2750 * Set the channel width and guard interval.
2752 if (IEEE80211_IS_CHAN_HT40(ni->ni_chan)) {
2753 plcp |= IWN_RFLAG_HT40;
2754 if (ni->ni_htcap & IEEE80211_HTCAP_SHORTGI40)
2755 plcp |= IWN_RFLAG_SGI;
2756 } else if (ni->ni_htcap & IEEE80211_HTCAP_SHORTGI20) {
2757 plcp |= IWN_RFLAG_SGI;
2761 * Ensure the selected rate matches the link quality
2762 * table entries being used.
2765 plcp |= IWN_RFLAG_ANT(sc->txchainmask);
2766 else if (rate > 0x87)
2767 plcp |= IWN_RFLAG_ANT(iwn_get_2stream_tx_antmask(sc));
2769 plcp |= IWN_RFLAG_ANT(iwn_get_1stream_tx_antmask(sc));
2772 * Set the initial PLCP - fine for both
2773 * OFDM and CCK rates.
2775 plcp = rate2plcp(rate);
2777 /* Set CCK flag if it's CCK */
2779 /* XXX It would be nice to have a method
2780 * to map the ridx -> phy table entry
2781 * so we could just query that, rather than
2782 * this hack to check against IWN_RIDX_OFDM6.
2784 ridx = ieee80211_legacy_rate_lookup(ic->ic_rt,
2785 rate & IEEE80211_RATE_VAL);
2786 if (ridx < IWN_RIDX_OFDM6 &&
2787 IEEE80211_IS_CHAN_2GHZ(ni->ni_chan))
2788 plcp |= IWN_RFLAG_CCK;
2790 /* Set antenna configuration */
2791 /* XXX TODO: is this the right antenna to use for legacy? */
2792 plcp |= IWN_RFLAG_ANT(iwn_get_1stream_tx_antmask(sc));
2795 DPRINTF(sc, IWN_DEBUG_TXRATE, "%s: rate=0x%02x, plcp=0x%08x\n",
2800 return (htole32(plcp));
2804 iwn_newassoc(struct ieee80211_node *ni, int isnew)
2806 /* Doesn't do anything at the moment */
2810 iwn_media_change(struct ifnet *ifp)
2814 error = ieee80211_media_change(ifp);
2815 /* NB: only the fixed rate can change and that doesn't need a reset */
2816 return (error == ENETRESET ? 0 : error);
2820 iwn_newstate(struct ieee80211vap *vap, enum ieee80211_state nstate, int arg)
2822 struct iwn_vap *ivp = IWN_VAP(vap);
2823 struct ieee80211com *ic = vap->iv_ic;
2824 struct iwn_softc *sc = ic->ic_softc;
2827 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
2829 DPRINTF(sc, IWN_DEBUG_STATE, "%s: %s -> %s\n", __func__,
2830 ieee80211_state_name[vap->iv_state], ieee80211_state_name[nstate]);
2832 IEEE80211_UNLOCK(ic);
2834 callout_stop(&sc->calib_to);
2836 sc->rxon = &sc->rx_on[IWN_RXON_BSS_CTX];
2839 case IEEE80211_S_ASSOC:
2840 if (vap->iv_state != IEEE80211_S_RUN)
2843 case IEEE80211_S_AUTH:
2844 if (vap->iv_state == IEEE80211_S_AUTH)
2848 * !AUTH -> AUTH transition requires state reset to handle
2849 * reassociations correctly.
2851 sc->rxon->associd = 0;
2852 sc->rxon->filter &= ~htole32(IWN_FILTER_BSS);
2853 sc->calib.state = IWN_CALIB_STATE_INIT;
2855 /* Wait until we hear a beacon before we transmit */
2856 if (IEEE80211_IS_CHAN_PASSIVE(ic->ic_curchan))
2857 sc->sc_beacon_wait = 1;
2859 if ((error = iwn_auth(sc, vap)) != 0) {
2860 device_printf(sc->sc_dev,
2861 "%s: could not move to auth state\n", __func__);
2865 case IEEE80211_S_RUN:
2867 * RUN -> RUN transition; Just restart the timers.
2869 if (vap->iv_state == IEEE80211_S_RUN) {
2874 /* Wait until we hear a beacon before we transmit */
2875 if (IEEE80211_IS_CHAN_PASSIVE(ic->ic_curchan))
2876 sc->sc_beacon_wait = 1;
2879 * !RUN -> RUN requires setting the association id
2880 * which is done with a firmware cmd. We also defer
2881 * starting the timers until that work is done.
2883 if ((error = iwn_run(sc, vap)) != 0) {
2884 device_printf(sc->sc_dev,
2885 "%s: could not move to run state\n", __func__);
2889 case IEEE80211_S_INIT:
2890 sc->calib.state = IWN_CALIB_STATE_INIT;
2892 * Purge the xmit queue so we don't have old frames
2893 * during a new association attempt.
2895 sc->sc_beacon_wait = 0;
2896 iwn_xmit_queue_drain(sc);
2905 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end in error\n", __func__);
2909 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
2911 return ivp->iv_newstate(vap, nstate, arg);
2915 iwn_calib_timeout(void *arg)
2917 struct iwn_softc *sc = arg;
2919 IWN_LOCK_ASSERT(sc);
2921 /* Force automatic TX power calibration every 60 secs. */
2922 if (++sc->calib_cnt >= 120) {
2925 DPRINTF(sc, IWN_DEBUG_CALIBRATE, "%s\n",
2926 "sending request for statistics");
2927 (void)iwn_cmd(sc, IWN_CMD_GET_STATISTICS, &flags,
2931 callout_reset(&sc->calib_to, msecs_to_ticks(500), iwn_calib_timeout,
2936 * Process an RX_PHY firmware notification. This is usually immediately
2937 * followed by an MPDU_RX_DONE notification.
2940 iwn_rx_phy(struct iwn_softc *sc, struct iwn_rx_desc *desc,
2941 struct iwn_rx_data *data)
2943 struct iwn_rx_stat *stat = (struct iwn_rx_stat *)(desc + 1);
2945 DPRINTF(sc, IWN_DEBUG_CALIBRATE, "%s: received PHY stats\n", __func__);
2946 bus_dmamap_sync(sc->rxq.data_dmat, data->map, BUS_DMASYNC_POSTREAD);
2948 /* Save RX statistics, they will be used on MPDU_RX_DONE. */
2949 memcpy(&sc->last_rx_stat, stat, sizeof (*stat));
2950 sc->last_rx_valid = 1;
2954 * Process an RX_DONE (4965AGN only) or MPDU_RX_DONE firmware notification.
2955 * Each MPDU_RX_DONE notification must be preceded by an RX_PHY one.
2958 iwn_rx_done(struct iwn_softc *sc, struct iwn_rx_desc *desc,
2959 struct iwn_rx_data *data)
2961 struct iwn_ops *ops = &sc->ops;
2962 struct ieee80211com *ic = &sc->sc_ic;
2963 struct iwn_rx_ring *ring = &sc->rxq;
2964 struct ieee80211_frame *wh;
2965 struct ieee80211_node *ni;
2966 struct mbuf *m, *m1;
2967 struct iwn_rx_stat *stat;
2971 int error, len, rssi, nf;
2973 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
2975 if (desc->type == IWN_MPDU_RX_DONE) {
2976 /* Check for prior RX_PHY notification. */
2977 if (!sc->last_rx_valid) {
2978 DPRINTF(sc, IWN_DEBUG_ANY,
2979 "%s: missing RX_PHY\n", __func__);
2982 stat = &sc->last_rx_stat;
2984 stat = (struct iwn_rx_stat *)(desc + 1);
2986 bus_dmamap_sync(ring->data_dmat, data->map, BUS_DMASYNC_POSTREAD);
2988 if (stat->cfg_phy_len > IWN_STAT_MAXLEN) {
2989 device_printf(sc->sc_dev,
2990 "%s: invalid RX statistic header, len %d\n", __func__,
2994 if (desc->type == IWN_MPDU_RX_DONE) {
2995 struct iwn_rx_mpdu *mpdu = (struct iwn_rx_mpdu *)(desc + 1);
2996 head = (caddr_t)(mpdu + 1);
2997 len = le16toh(mpdu->len);
2999 head = (caddr_t)(stat + 1) + stat->cfg_phy_len;
3000 len = le16toh(stat->len);
3003 flags = le32toh(*(uint32_t *)(head + len));
3005 /* Discard frames with a bad FCS early. */
3006 if ((flags & IWN_RX_NOERROR) != IWN_RX_NOERROR) {
3007 DPRINTF(sc, IWN_DEBUG_RECV, "%s: RX flags error %x\n",
3009 counter_u64_add(ic->ic_ierrors, 1);
3012 /* Discard frames that are too short. */
3013 if (len < sizeof (struct ieee80211_frame_ack)) {
3014 DPRINTF(sc, IWN_DEBUG_RECV, "%s: frame too short: %d\n",
3016 counter_u64_add(ic->ic_ierrors, 1);
3020 m1 = m_getjcl(M_NOWAIT, MT_DATA, M_PKTHDR, IWN_RBUF_SIZE);
3022 DPRINTF(sc, IWN_DEBUG_ANY, "%s: no mbuf to restock ring\n",
3024 counter_u64_add(ic->ic_ierrors, 1);
3027 bus_dmamap_unload(ring->data_dmat, data->map);
3029 error = bus_dmamap_load(ring->data_dmat, data->map, mtod(m1, void *),
3030 IWN_RBUF_SIZE, iwn_dma_map_addr, &paddr, BUS_DMA_NOWAIT);
3031 if (error != 0 && error != EFBIG) {
3032 device_printf(sc->sc_dev,
3033 "%s: bus_dmamap_load failed, error %d\n", __func__, error);
3036 /* Try to reload the old mbuf. */
3037 error = bus_dmamap_load(ring->data_dmat, data->map,
3038 mtod(data->m, void *), IWN_RBUF_SIZE, iwn_dma_map_addr,
3039 &paddr, BUS_DMA_NOWAIT);
3040 if (error != 0 && error != EFBIG) {
3041 panic("%s: could not load old RX mbuf", __func__);
3043 bus_dmamap_sync(ring->data_dmat, data->map,
3044 BUS_DMASYNC_PREREAD);
3045 /* Physical address may have changed. */
3046 ring->desc[ring->cur] = htole32(paddr >> 8);
3047 bus_dmamap_sync(ring->desc_dma.tag, ring->desc_dma.map,
3048 BUS_DMASYNC_PREWRITE);
3049 counter_u64_add(ic->ic_ierrors, 1);
3053 bus_dmamap_sync(ring->data_dmat, data->map,
3054 BUS_DMASYNC_PREREAD);
3058 /* Update RX descriptor. */
3059 ring->desc[ring->cur] = htole32(paddr >> 8);
3060 bus_dmamap_sync(ring->desc_dma.tag, ring->desc_dma.map,
3061 BUS_DMASYNC_PREWRITE);
3063 /* Finalize mbuf. */
3065 m->m_pkthdr.len = m->m_len = len;
3067 /* Grab a reference to the source node. */
3068 wh = mtod(m, struct ieee80211_frame *);
3069 if (len >= sizeof(struct ieee80211_frame_min))
3070 ni = ieee80211_find_rxnode(ic, (struct ieee80211_frame_min *)wh);
3073 nf = (ni != NULL && ni->ni_vap->iv_state == IEEE80211_S_RUN &&
3074 (ic->ic_flags & IEEE80211_F_SCAN) == 0) ? sc->noise : -95;
3076 rssi = ops->get_rssi(sc, stat);
3078 if (ieee80211_radiotap_active(ic)) {
3079 struct iwn_rx_radiotap_header *tap = &sc->sc_rxtap;
3082 if (stat->flags & htole16(IWN_STAT_FLAG_SHPREAMBLE))
3083 tap->wr_flags |= IEEE80211_RADIOTAP_F_SHORTPRE;
3084 tap->wr_dbm_antsignal = (int8_t)rssi;
3085 tap->wr_dbm_antnoise = (int8_t)nf;
3086 tap->wr_tsft = stat->tstamp;
3087 switch (stat->rate) {
3089 case 10: tap->wr_rate = 2; break;
3090 case 20: tap->wr_rate = 4; break;
3091 case 55: tap->wr_rate = 11; break;
3092 case 110: tap->wr_rate = 22; break;
3094 case 0xd: tap->wr_rate = 12; break;
3095 case 0xf: tap->wr_rate = 18; break;
3096 case 0x5: tap->wr_rate = 24; break;
3097 case 0x7: tap->wr_rate = 36; break;
3098 case 0x9: tap->wr_rate = 48; break;
3099 case 0xb: tap->wr_rate = 72; break;
3100 case 0x1: tap->wr_rate = 96; break;
3101 case 0x3: tap->wr_rate = 108; break;
3102 /* Unknown rate: should not happen. */
3103 default: tap->wr_rate = 0;
3108 * If it's a beacon and we're waiting, then do the
3109 * wakeup. This should unblock raw_xmit/start.
3111 if (sc->sc_beacon_wait) {
3112 uint8_t type, subtype;
3113 /* NB: Re-assign wh */
3114 wh = mtod(m, struct ieee80211_frame *);
3115 type = wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK;
3116 subtype = wh->i_fc[0] & IEEE80211_FC0_SUBTYPE_MASK;
3118 * This assumes at this point we've received our own
3121 DPRINTF(sc, IWN_DEBUG_TRACE,
3122 "%s: beacon_wait, type=%d, subtype=%d\n",
3123 __func__, type, subtype);
3124 if (type == IEEE80211_FC0_TYPE_MGT &&
3125 subtype == IEEE80211_FC0_SUBTYPE_BEACON) {
3126 DPRINTF(sc, IWN_DEBUG_TRACE | IWN_DEBUG_XMIT,
3127 "%s: waking things up\n", __func__);
3128 /* queue taskqueue to transmit! */
3129 taskqueue_enqueue(sc->sc_tq, &sc->sc_xmit_task);
3135 /* Send the frame to the 802.11 layer. */
3137 if (ni->ni_flags & IEEE80211_NODE_HT)
3138 m->m_flags |= M_AMPDU;
3139 (void)ieee80211_input(ni, m, rssi - nf, nf);
3140 /* Node is no longer needed. */
3141 ieee80211_free_node(ni);
3143 (void)ieee80211_input_all(ic, m, rssi - nf, nf);
3147 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
3151 /* Process an incoming Compressed BlockAck. */
3153 iwn_rx_compressed_ba(struct iwn_softc *sc, struct iwn_rx_desc *desc,
3154 struct iwn_rx_data *data)
3156 struct iwn_ops *ops = &sc->ops;
3157 struct iwn_node *wn;
3158 struct ieee80211_node *ni;
3159 struct iwn_compressed_ba *ba = (struct iwn_compressed_ba *)(desc + 1);
3160 struct iwn_tx_ring *txq;
3161 struct iwn_tx_data *txdata;
3162 struct ieee80211_tx_ampdu *tap;
3167 int ackfailcnt = 0, i, lastidx, qid, *res, shift;
3168 int tx_ok = 0, tx_err = 0;
3170 DPRINTF(sc, IWN_DEBUG_TRACE | IWN_DEBUG_XMIT, "->%s begin\n", __func__);
3172 bus_dmamap_sync(sc->rxq.data_dmat, data->map, BUS_DMASYNC_POSTREAD);
3174 qid = le16toh(ba->qid);
3175 txq = &sc->txq[ba->qid];
3176 tap = sc->qid2tap[ba->qid];
3178 wn = (void *)tap->txa_ni;
3182 if (!IEEE80211_AMPDU_RUNNING(tap)) {
3183 res = tap->txa_private;
3184 ssn = tap->txa_start & 0xfff;
3187 for (lastidx = le16toh(ba->ssn) & 0xff; txq->read != lastidx;) {
3188 txdata = &txq->data[txq->read];
3190 /* Unmap and free mbuf. */
3191 bus_dmamap_sync(txq->data_dmat, txdata->map,
3192 BUS_DMASYNC_POSTWRITE);
3193 bus_dmamap_unload(txq->data_dmat, txdata->map);
3194 m = txdata->m, txdata->m = NULL;
3195 ni = txdata->ni, txdata->ni = NULL;
3197 KASSERT(ni != NULL, ("no node"));
3198 KASSERT(m != NULL, ("no mbuf"));
3200 DPRINTF(sc, IWN_DEBUG_XMIT, "%s: freeing m=%p\n", __func__, m);
3201 ieee80211_tx_complete(ni, m, 1);
3204 txq->read = (txq->read + 1) % IWN_TX_RING_COUNT;
3207 if (txq->queued == 0 && res != NULL) {
3209 ops->ampdu_tx_stop(sc, qid, tid, ssn);
3211 sc->qid2tap[qid] = NULL;
3212 free(res, M_DEVBUF);
3216 if (wn->agg[tid].bitmap == 0)
3219 shift = wn->agg[tid].startidx - ((le16toh(ba->seq) >> 4) & 0xff);
3223 if (wn->agg[tid].nframes > (64 - shift))
3227 * Walk the bitmap and calculate how many successful and failed
3228 * attempts are made.
3230 * Yes, the rate control code doesn't know these are A-MPDU
3231 * subframes and that it's okay to fail some of these.
3234 bitmap = (le64toh(ba->bitmap) >> shift) & wn->agg[tid].bitmap;
3235 for (i = 0; bitmap; i++) {
3236 if ((bitmap & 1) == 0) {
3238 ieee80211_ratectl_tx_complete(ni->ni_vap, ni,
3239 IEEE80211_RATECTL_TX_FAILURE, &ackfailcnt, NULL);
3242 ieee80211_ratectl_tx_complete(ni->ni_vap, ni,
3243 IEEE80211_RATECTL_TX_SUCCESS, &ackfailcnt, NULL);
3248 DPRINTF(sc, IWN_DEBUG_TRACE | IWN_DEBUG_XMIT,
3249 "->%s: end; %d ok; %d err\n",__func__, tx_ok, tx_err);
3254 * Process a CALIBRATION_RESULT notification sent by the initialization
3255 * firmware on response to a CMD_CALIB_CONFIG command (5000 only).
3258 iwn5000_rx_calib_results(struct iwn_softc *sc, struct iwn_rx_desc *desc,
3259 struct iwn_rx_data *data)
3261 struct iwn_phy_calib *calib = (struct iwn_phy_calib *)(desc + 1);
3264 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
3266 /* Runtime firmware should not send such a notification. */
3267 if (sc->sc_flags & IWN_FLAG_CALIB_DONE){
3268 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s received after clib done\n",
3272 len = (le32toh(desc->len) & 0x3fff) - 4;
3273 bus_dmamap_sync(sc->rxq.data_dmat, data->map, BUS_DMASYNC_POSTREAD);
3275 switch (calib->code) {
3276 case IWN5000_PHY_CALIB_DC:
3277 if (sc->base_params->calib_need & IWN_FLG_NEED_PHY_CALIB_DC)
3280 case IWN5000_PHY_CALIB_LO:
3281 if (sc->base_params->calib_need & IWN_FLG_NEED_PHY_CALIB_LO)
3284 case IWN5000_PHY_CALIB_TX_IQ:
3285 if (sc->base_params->calib_need & IWN_FLG_NEED_PHY_CALIB_TX_IQ)
3288 case IWN5000_PHY_CALIB_TX_IQ_PERIODIC:
3289 if (sc->base_params->calib_need & IWN_FLG_NEED_PHY_CALIB_TX_IQ_PERIODIC)
3292 case IWN5000_PHY_CALIB_BASE_BAND:
3293 if (sc->base_params->calib_need & IWN_FLG_NEED_PHY_CALIB_BASE_BAND)
3297 if (idx == -1) /* Ignore other results. */
3300 /* Save calibration result. */
3301 if (sc->calibcmd[idx].buf != NULL)
3302 free(sc->calibcmd[idx].buf, M_DEVBUF);
3303 sc->calibcmd[idx].buf = malloc(len, M_DEVBUF, M_NOWAIT);
3304 if (sc->calibcmd[idx].buf == NULL) {
3305 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
3306 "not enough memory for calibration result %d\n",
3310 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
3311 "saving calibration result idx=%d, code=%d len=%d\n", idx, calib->code, len);
3312 sc->calibcmd[idx].len = len;
3313 memcpy(sc->calibcmd[idx].buf, calib, len);
3317 iwn_stats_update(struct iwn_softc *sc, struct iwn_calib_state *calib,
3318 struct iwn_stats *stats, int len)
3320 struct iwn_stats_bt *stats_bt;
3321 struct iwn_stats *lstats;
3324 * First - check whether the length is the bluetooth or normal.
3326 * If it's normal - just copy it and bump out.
3327 * Otherwise we have to convert things.
3330 if (len == sizeof(struct iwn_stats) + 4) {
3331 memcpy(&sc->last_stat, stats, sizeof(struct iwn_stats));
3332 sc->last_stat_valid = 1;
3337 * If it's not the bluetooth size - log, then just copy.
3339 if (len != sizeof(struct iwn_stats_bt) + 4) {
3340 DPRINTF(sc, IWN_DEBUG_STATS,
3341 "%s: size of rx statistics (%d) not an expected size!\n",
3344 memcpy(&sc->last_stat, stats, sizeof(struct iwn_stats));
3345 sc->last_stat_valid = 1;
3352 stats_bt = (struct iwn_stats_bt *) stats;
3353 lstats = &sc->last_stat;
3356 lstats->flags = stats_bt->flags;
3358 memcpy(&lstats->rx.ofdm, &stats_bt->rx_bt.ofdm,
3359 sizeof(struct iwn_rx_phy_stats));
3360 memcpy(&lstats->rx.cck, &stats_bt->rx_bt.cck,
3361 sizeof(struct iwn_rx_phy_stats));
3362 memcpy(&lstats->rx.general, &stats_bt->rx_bt.general_bt.common,
3363 sizeof(struct iwn_rx_general_stats));
3364 memcpy(&lstats->rx.ht, &stats_bt->rx_bt.ht,
3365 sizeof(struct iwn_rx_ht_phy_stats));
3367 memcpy(&lstats->tx, &stats_bt->tx,
3368 sizeof(struct iwn_tx_stats));
3370 memcpy(&lstats->general, &stats_bt->general,
3371 sizeof(struct iwn_general_stats));
3373 /* XXX TODO: Squirrel away the extra bluetooth stats somewhere */
3374 sc->last_stat_valid = 1;
3378 * Process an RX_STATISTICS or BEACON_STATISTICS firmware notification.
3379 * The latter is sent by the firmware after each received beacon.
3382 iwn_rx_statistics(struct iwn_softc *sc, struct iwn_rx_desc *desc,
3383 struct iwn_rx_data *data)
3385 struct iwn_ops *ops = &sc->ops;
3386 struct ieee80211com *ic = &sc->sc_ic;
3387 struct ieee80211vap *vap = TAILQ_FIRST(&ic->ic_vaps);
3388 struct iwn_calib_state *calib = &sc->calib;
3389 struct iwn_stats *stats = (struct iwn_stats *)(desc + 1);
3390 struct iwn_stats *lstats;
3393 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
3395 /* Ignore statistics received during a scan. */
3396 if (vap->iv_state != IEEE80211_S_RUN ||
3397 (ic->ic_flags & IEEE80211_F_SCAN)){
3398 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s received during calib\n",
3403 bus_dmamap_sync(sc->rxq.data_dmat, data->map, BUS_DMASYNC_POSTREAD);
3405 DPRINTF(sc, IWN_DEBUG_CALIBRATE | IWN_DEBUG_STATS,
3406 "%s: received statistics, cmd %d, len %d\n",
3407 __func__, desc->type, le16toh(desc->len));
3408 sc->calib_cnt = 0; /* Reset TX power calibration timeout. */
3411 * Collect/track general statistics for reporting.
3413 * This takes care of ensuring that the bluetooth sized message
3414 * will be correctly converted to the legacy sized message.
3416 iwn_stats_update(sc, calib, stats, le16toh(desc->len));
3419 * And now, let's take a reference of it to use!
3421 lstats = &sc->last_stat;
3423 /* Test if temperature has changed. */
3424 if (lstats->general.temp != sc->rawtemp) {
3425 /* Convert "raw" temperature to degC. */
3426 sc->rawtemp = stats->general.temp;
3427 temp = ops->get_temperature(sc);
3428 DPRINTF(sc, IWN_DEBUG_CALIBRATE, "%s: temperature %d\n",
3431 /* Update TX power if need be (4965AGN only). */
3432 if (sc->hw_type == IWN_HW_REV_TYPE_4965)
3433 iwn4965_power_calibration(sc, temp);
3436 if (desc->type != IWN_BEACON_STATISTICS)
3437 return; /* Reply to a statistics request. */
3439 sc->noise = iwn_get_noise(&lstats->rx.general);
3440 DPRINTF(sc, IWN_DEBUG_CALIBRATE, "%s: noise %d\n", __func__, sc->noise);
3442 /* Test that RSSI and noise are present in stats report. */
3443 if (le32toh(lstats->rx.general.flags) != 1) {
3444 DPRINTF(sc, IWN_DEBUG_ANY, "%s\n",
3445 "received statistics without RSSI");
3449 if (calib->state == IWN_CALIB_STATE_ASSOC)
3450 iwn_collect_noise(sc, &lstats->rx.general);
3451 else if (calib->state == IWN_CALIB_STATE_RUN) {
3452 iwn_tune_sensitivity(sc, &lstats->rx);
3454 * XXX TODO: Only run the RX recovery if we're associated!
3456 iwn_check_rx_recovery(sc, lstats);
3457 iwn_save_stats_counters(sc, lstats);
3460 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
3464 * Save the relevant statistic counters for the next calibration
3468 iwn_save_stats_counters(struct iwn_softc *sc, const struct iwn_stats *rs)
3470 struct iwn_calib_state *calib = &sc->calib;
3472 /* Save counters values for next call. */
3473 calib->bad_plcp_cck = le32toh(rs->rx.cck.bad_plcp);
3474 calib->fa_cck = le32toh(rs->rx.cck.fa);
3475 calib->bad_plcp_ht = le32toh(rs->rx.ht.bad_plcp);
3476 calib->bad_plcp_ofdm = le32toh(rs->rx.ofdm.bad_plcp);
3477 calib->fa_ofdm = le32toh(rs->rx.ofdm.fa);
3479 /* Last time we received these tick values */
3480 sc->last_calib_ticks = ticks;
3484 * Process a TX_DONE firmware notification. Unfortunately, the 4965AGN
3485 * and 5000 adapters have different incompatible TX status formats.
3488 iwn4965_tx_done(struct iwn_softc *sc, struct iwn_rx_desc *desc,
3489 struct iwn_rx_data *data)
3491 struct iwn4965_tx_stat *stat = (struct iwn4965_tx_stat *)(desc + 1);
3492 struct iwn_tx_ring *ring;
3495 qid = desc->qid & 0xf;
3496 ring = &sc->txq[qid];
3498 DPRINTF(sc, IWN_DEBUG_XMIT, "%s: "
3499 "qid %d idx %d RTS retries %d ACK retries %d nkill %d rate %x duration %d status %x\n",
3500 __func__, desc->qid, desc->idx,
3504 stat->rate, le16toh(stat->duration),
3505 le32toh(stat->status));
3507 bus_dmamap_sync(ring->data_dmat, data->map, BUS_DMASYNC_POSTREAD);
3508 if (qid >= sc->firstaggqueue) {
3509 iwn_ampdu_tx_done(sc, qid, desc->idx, stat->nframes,
3510 stat->ackfailcnt, &stat->status);
3512 iwn_tx_done(sc, desc, stat->ackfailcnt,
3513 le32toh(stat->status) & 0xff);
3518 iwn5000_tx_done(struct iwn_softc *sc, struct iwn_rx_desc *desc,
3519 struct iwn_rx_data *data)
3521 struct iwn5000_tx_stat *stat = (struct iwn5000_tx_stat *)(desc + 1);
3522 struct iwn_tx_ring *ring;
3525 qid = desc->qid & 0xf;
3526 ring = &sc->txq[qid];
3528 DPRINTF(sc, IWN_DEBUG_XMIT, "%s: "
3529 "qid %d idx %d RTS retries %d ACK retries %d nkill %d rate %x duration %d status %x\n",
3530 __func__, desc->qid, desc->idx,
3534 stat->rate, le16toh(stat->duration),
3535 le32toh(stat->status));
3538 /* Reset TX scheduler slot. */
3539 iwn5000_reset_sched(sc, desc->qid & 0xf, desc->idx);
3542 bus_dmamap_sync(ring->data_dmat, data->map, BUS_DMASYNC_POSTREAD);
3543 if (qid >= sc->firstaggqueue) {
3544 iwn_ampdu_tx_done(sc, qid, desc->idx, stat->nframes,
3545 stat->ackfailcnt, &stat->status);
3547 iwn_tx_done(sc, desc, stat->ackfailcnt,
3548 le16toh(stat->status) & 0xff);
3553 * Adapter-independent backend for TX_DONE firmware notifications.
3556 iwn_tx_done(struct iwn_softc *sc, struct iwn_rx_desc *desc, int ackfailcnt,
3559 struct iwn_tx_ring *ring = &sc->txq[desc->qid & 0xf];
3560 struct iwn_tx_data *data = &ring->data[desc->idx];
3562 struct ieee80211_node *ni;
3563 struct ieee80211vap *vap;
3565 KASSERT(data->ni != NULL, ("no node"));
3567 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
3569 /* Unmap and free mbuf. */
3570 bus_dmamap_sync(ring->data_dmat, data->map, BUS_DMASYNC_POSTWRITE);
3571 bus_dmamap_unload(ring->data_dmat, data->map);
3572 m = data->m, data->m = NULL;
3573 ni = data->ni, data->ni = NULL;
3577 * Update rate control statistics for the node.
3579 if (status & IWN_TX_FAIL)
3580 ieee80211_ratectl_tx_complete(vap, ni,
3581 IEEE80211_RATECTL_TX_FAILURE, &ackfailcnt, NULL);
3583 ieee80211_ratectl_tx_complete(vap, ni,
3584 IEEE80211_RATECTL_TX_SUCCESS, &ackfailcnt, NULL);
3587 * Channels marked for "radar" require traffic to be received
3588 * to unlock before we can transmit. Until traffic is seen
3589 * any attempt to transmit is returned immediately with status
3590 * set to IWN_TX_FAIL_TX_LOCKED. Unfortunately this can easily
3591 * happen on first authenticate after scanning. To workaround
3592 * this we ignore a failure of this sort in AUTH state so the
3593 * 802.11 layer will fall back to using a timeout to wait for
3594 * the AUTH reply. This allows the firmware time to see
3595 * traffic so a subsequent retry of AUTH succeeds. It's
3596 * unclear why the firmware does not maintain state for
3597 * channels recently visited as this would allow immediate
3598 * use of the channel after a scan (where we see traffic).
3600 if (status == IWN_TX_FAIL_TX_LOCKED &&
3601 ni->ni_vap->iv_state == IEEE80211_S_AUTH)
3602 ieee80211_tx_complete(ni, m, 0);
3604 ieee80211_tx_complete(ni, m,
3605 (status & IWN_TX_FAIL) != 0);
3607 sc->sc_tx_timer = 0;
3608 if (--ring->queued < IWN_TX_RING_LOMARK)
3609 sc->qfullmsk &= ~(1 << ring->qid);
3611 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
3615 * Process a "command done" firmware notification. This is where we wakeup
3616 * processes waiting for a synchronous command completion.
3619 iwn_cmd_done(struct iwn_softc *sc, struct iwn_rx_desc *desc)
3621 struct iwn_tx_ring *ring;
3622 struct iwn_tx_data *data;
3625 if (sc->sc_flags & IWN_FLAG_PAN_SUPPORT)
3626 cmd_queue_num = IWN_PAN_CMD_QUEUE;
3628 cmd_queue_num = IWN_CMD_QUEUE_NUM;
3630 if ((desc->qid & IWN_RX_DESC_QID_MSK) != cmd_queue_num)
3631 return; /* Not a command ack. */
3633 ring = &sc->txq[cmd_queue_num];
3634 data = &ring->data[desc->idx];
3636 /* If the command was mapped in an mbuf, free it. */
3637 if (data->m != NULL) {
3638 bus_dmamap_sync(ring->data_dmat, data->map,
3639 BUS_DMASYNC_POSTWRITE);
3640 bus_dmamap_unload(ring->data_dmat, data->map);
3644 wakeup(&ring->desc[desc->idx]);
3648 iwn_ampdu_tx_done(struct iwn_softc *sc, int qid, int idx, int nframes,
3649 int ackfailcnt, void *stat)
3651 struct iwn_ops *ops = &sc->ops;
3652 struct iwn_tx_ring *ring = &sc->txq[qid];
3653 struct iwn_tx_data *data;
3655 struct iwn_node *wn;
3656 struct ieee80211_node *ni;
3657 struct ieee80211_tx_ampdu *tap;
3659 uint32_t *status = stat;
3660 uint16_t *aggstatus = stat;
3663 int bit, i, lastidx, *res, seqno, shift, start;
3665 /* XXX TODO: status is le16 field! Grr */
3667 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
3668 DPRINTF(sc, IWN_DEBUG_XMIT, "%s: nframes=%d, status=0x%08x\n",
3673 tap = sc->qid2tap[qid];
3675 wn = (void *)tap->txa_ni;
3679 * XXX TODO: ACK and RTS failures would be nice here!
3683 * A-MPDU single frame status - if we failed to transmit it
3684 * in A-MPDU, then it may be a permanent failure.
3686 * XXX TODO: check what the Linux iwlwifi driver does here;
3687 * there's some permanent and temporary failures that may be
3688 * handled differently.
3691 if ((*status & 0xff) != 1 && (*status & 0xff) != 2) {
3693 printf("ieee80211_send_bar()\n");
3696 * If we completely fail a transmit, make sure a
3697 * notification is pushed up to the rate control
3700 ieee80211_ratectl_tx_complete(ni->ni_vap,
3702 IEEE80211_RATECTL_TX_FAILURE,
3707 * If nframes=1, then we won't be getting a BA for
3708 * this frame. Ensure that we correctly update the
3709 * rate control code with how many retries were
3710 * needed to send it.
3712 ieee80211_ratectl_tx_complete(ni->ni_vap,
3714 IEEE80211_RATECTL_TX_SUCCESS,
3722 for (i = 0; i < nframes; i++) {
3723 if (le16toh(aggstatus[i * 2]) & 0xc)
3726 idx = le16toh(aggstatus[2*i + 1]) & 0xff;
3730 shift = 0x100 - idx + start;
3733 } else if (bit <= -64)
3734 bit = 0x100 - start + idx;
3736 shift = start - idx;
3740 bitmap = bitmap << shift;
3741 bitmap |= 1ULL << bit;
3743 tap = sc->qid2tap[qid];
3745 wn = (void *)tap->txa_ni;
3746 wn->agg[tid].bitmap = bitmap;
3747 wn->agg[tid].startidx = start;
3748 wn->agg[tid].nframes = nframes;
3752 if (!IEEE80211_AMPDU_RUNNING(tap)) {
3753 res = tap->txa_private;
3754 ssn = tap->txa_start & 0xfff;
3757 /* This is going nframes DWORDS into the descriptor? */
3758 seqno = le32toh(*(status + nframes)) & 0xfff;
3759 for (lastidx = (seqno & 0xff); ring->read != lastidx;) {
3760 data = &ring->data[ring->read];
3762 /* Unmap and free mbuf. */
3763 bus_dmamap_sync(ring->data_dmat, data->map,
3764 BUS_DMASYNC_POSTWRITE);
3765 bus_dmamap_unload(ring->data_dmat, data->map);
3766 m = data->m, data->m = NULL;
3767 ni = data->ni, data->ni = NULL;
3769 KASSERT(ni != NULL, ("no node"));
3770 KASSERT(m != NULL, ("no mbuf"));
3771 DPRINTF(sc, IWN_DEBUG_XMIT, "%s: freeing m=%p\n", __func__, m);
3772 ieee80211_tx_complete(ni, m, 1);
3775 ring->read = (ring->read + 1) % IWN_TX_RING_COUNT;
3778 if (ring->queued == 0 && res != NULL) {
3780 ops->ampdu_tx_stop(sc, qid, tid, ssn);
3782 sc->qid2tap[qid] = NULL;
3783 free(res, M_DEVBUF);
3787 sc->sc_tx_timer = 0;
3788 if (ring->queued < IWN_TX_RING_LOMARK)
3789 sc->qfullmsk &= ~(1 << ring->qid);
3791 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
3795 * Process an INT_FH_RX or INT_SW_RX interrupt.
3798 iwn_notif_intr(struct iwn_softc *sc)
3800 struct iwn_ops *ops = &sc->ops;
3801 struct ieee80211com *ic = &sc->sc_ic;
3802 struct ieee80211vap *vap = TAILQ_FIRST(&ic->ic_vaps);
3806 bus_dmamap_sync(sc->rxq.stat_dma.tag, sc->rxq.stat_dma.map,
3807 BUS_DMASYNC_POSTREAD);
3809 hw = le16toh(sc->rxq.stat->closed_count) & 0xfff;
3810 while (sc->rxq.cur != hw) {
3811 struct iwn_rx_data *data = &sc->rxq.data[sc->rxq.cur];
3812 struct iwn_rx_desc *desc;
3814 bus_dmamap_sync(sc->rxq.data_dmat, data->map,
3815 BUS_DMASYNC_POSTREAD);
3816 desc = mtod(data->m, struct iwn_rx_desc *);
3818 DPRINTF(sc, IWN_DEBUG_RECV,
3819 "%s: cur=%d; qid %x idx %d flags %x type %d(%s) len %d\n",
3820 __func__, sc->rxq.cur, desc->qid & 0xf, desc->idx, desc->flags,
3821 desc->type, iwn_intr_str(desc->type),
3822 le16toh(desc->len));
3824 if (!(desc->qid & IWN_UNSOLICITED_RX_NOTIF)) /* Reply to a command. */
3825 iwn_cmd_done(sc, desc);
3827 switch (desc->type) {
3829 iwn_rx_phy(sc, desc, data);
3832 case IWN_RX_DONE: /* 4965AGN only. */
3833 case IWN_MPDU_RX_DONE:
3834 /* An 802.11 frame has been received. */
3835 iwn_rx_done(sc, desc, data);
3837 is_stopped = (sc->sc_flags & IWN_FLAG_RUNNING) == 0;
3838 if (__predict_false(is_stopped))
3843 case IWN_RX_COMPRESSED_BA:
3844 /* A Compressed BlockAck has been received. */
3845 iwn_rx_compressed_ba(sc, desc, data);
3849 /* An 802.11 frame has been transmitted. */
3850 ops->tx_done(sc, desc, data);
3853 case IWN_RX_STATISTICS:
3854 case IWN_BEACON_STATISTICS:
3855 iwn_rx_statistics(sc, desc, data);
3858 case IWN_BEACON_MISSED:
3860 struct iwn_beacon_missed *miss =
3861 (struct iwn_beacon_missed *)(desc + 1);
3864 bus_dmamap_sync(sc->rxq.data_dmat, data->map,
3865 BUS_DMASYNC_POSTREAD);
3866 misses = le32toh(miss->consecutive);
3868 DPRINTF(sc, IWN_DEBUG_STATE,
3869 "%s: beacons missed %d/%d\n", __func__,
3870 misses, le32toh(miss->total));
3872 * If more than 5 consecutive beacons are missed,
3873 * reinitialize the sensitivity state machine.
3875 if (vap->iv_state == IEEE80211_S_RUN &&
3876 (ic->ic_flags & IEEE80211_F_SCAN) == 0) {
3878 (void)iwn_init_sensitivity(sc);
3879 if (misses >= vap->iv_bmissthreshold) {
3881 ieee80211_beacon_miss(ic);
3884 is_stopped = (sc->sc_flags &
3885 IWN_FLAG_RUNNING) == 0;
3886 if (__predict_false(is_stopped))
3894 struct iwn_ucode_info *uc =
3895 (struct iwn_ucode_info *)(desc + 1);
3897 /* The microcontroller is ready. */
3898 bus_dmamap_sync(sc->rxq.data_dmat, data->map,
3899 BUS_DMASYNC_POSTREAD);
3900 DPRINTF(sc, IWN_DEBUG_RESET,
3901 "microcode alive notification version=%d.%d "
3902 "subtype=%x alive=%x\n", uc->major, uc->minor,
3903 uc->subtype, le32toh(uc->valid));
3905 if (le32toh(uc->valid) != 1) {
3906 device_printf(sc->sc_dev,
3907 "microcontroller initialization failed");
3910 if (uc->subtype == IWN_UCODE_INIT) {
3911 /* Save microcontroller report. */
3912 memcpy(&sc->ucode_info, uc, sizeof (*uc));
3914 /* Save the address of the error log in SRAM. */
3915 sc->errptr = le32toh(uc->errptr);
3918 case IWN_STATE_CHANGED:
3921 * State change allows hardware switch change to be
3922 * noted. However, we handle this in iwn_intr as we
3923 * get both the enable/disble intr.
3925 bus_dmamap_sync(sc->rxq.data_dmat, data->map,
3926 BUS_DMASYNC_POSTREAD);
3928 uint32_t *status = (uint32_t *)(desc + 1);
3929 DPRINTF(sc, IWN_DEBUG_INTR | IWN_DEBUG_STATE,
3930 "state changed to %x\n",
3935 case IWN_START_SCAN:
3937 bus_dmamap_sync(sc->rxq.data_dmat, data->map,
3938 BUS_DMASYNC_POSTREAD);
3940 struct iwn_start_scan *scan =
3941 (struct iwn_start_scan *)(desc + 1);
3942 DPRINTF(sc, IWN_DEBUG_ANY,
3943 "%s: scanning channel %d status %x\n",
3944 __func__, scan->chan, le32toh(scan->status));
3950 bus_dmamap_sync(sc->rxq.data_dmat, data->map,
3951 BUS_DMASYNC_POSTREAD);
3953 struct iwn_stop_scan *scan =
3954 (struct iwn_stop_scan *)(desc + 1);
3955 DPRINTF(sc, IWN_DEBUG_STATE | IWN_DEBUG_SCAN,
3956 "scan finished nchan=%d status=%d chan=%d\n",
3957 scan->nchan, scan->status, scan->chan);
3959 sc->sc_is_scanning = 0;
3960 callout_stop(&sc->scan_timeout);
3962 ieee80211_scan_next(vap);
3965 is_stopped = (sc->sc_flags & IWN_FLAG_RUNNING) == 0;
3966 if (__predict_false(is_stopped))
3971 case IWN5000_CALIBRATION_RESULT:
3972 iwn5000_rx_calib_results(sc, desc, data);
3975 case IWN5000_CALIBRATION_DONE:
3976 sc->sc_flags |= IWN_FLAG_CALIB_DONE;
3981 sc->rxq.cur = (sc->rxq.cur + 1) % IWN_RX_RING_COUNT;
3984 /* Tell the firmware what we have processed. */
3985 hw = (hw == 0) ? IWN_RX_RING_COUNT - 1 : hw - 1;
3986 IWN_WRITE(sc, IWN_FH_RX_WPTR, hw & ~7);
3990 * Process an INT_WAKEUP interrupt raised when the microcontroller wakes up
3991 * from power-down sleep mode.
3994 iwn_wakeup_intr(struct iwn_softc *sc)
3998 DPRINTF(sc, IWN_DEBUG_RESET, "%s: ucode wakeup from power-down sleep\n",
4001 /* Wakeup RX and TX rings. */
4002 IWN_WRITE(sc, IWN_FH_RX_WPTR, sc->rxq.cur & ~7);
4003 for (qid = 0; qid < sc->ntxqs; qid++) {
4004 struct iwn_tx_ring *ring = &sc->txq[qid];
4005 IWN_WRITE(sc, IWN_HBUS_TARG_WRPTR, qid << 8 | ring->cur);
4010 iwn_rftoggle_intr(struct iwn_softc *sc)
4012 struct ieee80211com *ic = &sc->sc_ic;
4013 uint32_t tmp = IWN_READ(sc, IWN_GP_CNTRL);
4015 IWN_LOCK_ASSERT(sc);
4017 device_printf(sc->sc_dev, "RF switch: radio %s\n",
4018 (tmp & IWN_GP_CNTRL_RFKILL) ? "enabled" : "disabled");
4019 if (tmp & IWN_GP_CNTRL_RFKILL)
4020 ieee80211_runtask(ic, &sc->sc_radioon_task);
4022 ieee80211_runtask(ic, &sc->sc_radiooff_task);
4026 * Dump the error log of the firmware when a firmware panic occurs. Although
4027 * we can't debug the firmware because it is neither open source nor free, it
4028 * can help us to identify certain classes of problems.
4031 iwn_fatal_intr(struct iwn_softc *sc)
4033 struct iwn_fw_dump dump;
4036 IWN_LOCK_ASSERT(sc);
4038 /* Force a complete recalibration on next init. */
4039 sc->sc_flags &= ~IWN_FLAG_CALIB_DONE;
4041 /* Check that the error log address is valid. */
4042 if (sc->errptr < IWN_FW_DATA_BASE ||
4043 sc->errptr + sizeof (dump) >
4044 IWN_FW_DATA_BASE + sc->fw_data_maxsz) {
4045 printf("%s: bad firmware error log address 0x%08x\n", __func__,
4049 if (iwn_nic_lock(sc) != 0) {
4050 printf("%s: could not read firmware error log\n", __func__);
4053 /* Read firmware error log from SRAM. */
4054 iwn_mem_read_region_4(sc, sc->errptr, (uint32_t *)&dump,
4055 sizeof (dump) / sizeof (uint32_t));
4058 if (dump.valid == 0) {
4059 printf("%s: firmware error log is empty\n", __func__);
4062 printf("firmware error log:\n");
4063 printf(" error type = \"%s\" (0x%08X)\n",
4064 (dump.id < nitems(iwn_fw_errmsg)) ?
4065 iwn_fw_errmsg[dump.id] : "UNKNOWN",
4067 printf(" program counter = 0x%08X\n", dump.pc);
4068 printf(" source line = 0x%08X\n", dump.src_line);
4069 printf(" error data = 0x%08X%08X\n",
4070 dump.error_data[0], dump.error_data[1]);
4071 printf(" branch link = 0x%08X%08X\n",
4072 dump.branch_link[0], dump.branch_link[1]);
4073 printf(" interrupt link = 0x%08X%08X\n",
4074 dump.interrupt_link[0], dump.interrupt_link[1]);
4075 printf(" time = %u\n", dump.time[0]);
4077 /* Dump driver status (TX and RX rings) while we're here. */
4078 printf("driver status:\n");
4079 for (i = 0; i < sc->ntxqs; i++) {
4080 struct iwn_tx_ring *ring = &sc->txq[i];
4081 printf(" tx ring %2d: qid=%-2d cur=%-3d queued=%-3d\n",
4082 i, ring->qid, ring->cur, ring->queued);
4084 printf(" rx ring: cur=%d\n", sc->rxq.cur);
4090 struct iwn_softc *sc = arg;
4091 uint32_t r1, r2, tmp;
4095 /* Disable interrupts. */
4096 IWN_WRITE(sc, IWN_INT_MASK, 0);
4098 /* Read interrupts from ICT (fast) or from registers (slow). */
4099 if (sc->sc_flags & IWN_FLAG_USE_ICT) {
4100 bus_dmamap_sync(sc->ict_dma.tag, sc->ict_dma.map,
4101 BUS_DMASYNC_POSTREAD);
4103 while (sc->ict[sc->ict_cur] != 0) {
4104 tmp |= sc->ict[sc->ict_cur];
4105 sc->ict[sc->ict_cur] = 0; /* Acknowledge. */
4106 sc->ict_cur = (sc->ict_cur + 1) % IWN_ICT_COUNT;
4109 if (tmp == 0xffffffff) /* Shouldn't happen. */
4111 else if (tmp & 0xc0000) /* Workaround a HW bug. */
4113 r1 = (tmp & 0xff00) << 16 | (tmp & 0xff);
4114 r2 = 0; /* Unused. */
4116 r1 = IWN_READ(sc, IWN_INT);
4117 if (r1 == 0xffffffff || (r1 & 0xfffffff0) == 0xa5a5a5a0) {
4119 return; /* Hardware gone! */
4121 r2 = IWN_READ(sc, IWN_FH_INT);
4124 DPRINTF(sc, IWN_DEBUG_INTR, "interrupt reg1=0x%08x reg2=0x%08x\n"
4127 if (r1 == 0 && r2 == 0)
4128 goto done; /* Interrupt not for us. */
4130 /* Acknowledge interrupts. */
4131 IWN_WRITE(sc, IWN_INT, r1);
4132 if (!(sc->sc_flags & IWN_FLAG_USE_ICT))
4133 IWN_WRITE(sc, IWN_FH_INT, r2);
4135 if (r1 & IWN_INT_RF_TOGGLED) {
4136 iwn_rftoggle_intr(sc);
4139 if (r1 & IWN_INT_CT_REACHED) {
4140 device_printf(sc->sc_dev, "%s: critical temperature reached!\n",
4143 if (r1 & (IWN_INT_SW_ERR | IWN_INT_HW_ERR)) {
4144 device_printf(sc->sc_dev, "%s: fatal firmware error\n",
4147 iwn_debug_register(sc);
4149 /* Dump firmware error log and stop. */
4152 taskqueue_enqueue(sc->sc_tq, &sc->sc_panic_task);
4155 if ((r1 & (IWN_INT_FH_RX | IWN_INT_SW_RX | IWN_INT_RX_PERIODIC)) ||
4156 (r2 & IWN_FH_INT_RX)) {
4157 if (sc->sc_flags & IWN_FLAG_USE_ICT) {
4158 if (r1 & (IWN_INT_FH_RX | IWN_INT_SW_RX))
4159 IWN_WRITE(sc, IWN_FH_INT, IWN_FH_INT_RX);
4160 IWN_WRITE_1(sc, IWN_INT_PERIODIC,
4161 IWN_INT_PERIODIC_DIS);
4163 if (r1 & (IWN_INT_FH_RX | IWN_INT_SW_RX)) {
4164 IWN_WRITE_1(sc, IWN_INT_PERIODIC,
4165 IWN_INT_PERIODIC_ENA);
4171 if ((r1 & IWN_INT_FH_TX) || (r2 & IWN_FH_INT_TX)) {
4172 if (sc->sc_flags & IWN_FLAG_USE_ICT)
4173 IWN_WRITE(sc, IWN_FH_INT, IWN_FH_INT_TX);
4174 wakeup(sc); /* FH DMA transfer completed. */
4177 if (r1 & IWN_INT_ALIVE)
4178 wakeup(sc); /* Firmware is alive. */
4180 if (r1 & IWN_INT_WAKEUP)
4181 iwn_wakeup_intr(sc);
4184 /* Re-enable interrupts. */
4185 if (sc->sc_flags & IWN_FLAG_RUNNING)
4186 IWN_WRITE(sc, IWN_INT_MASK, sc->int_mask);
4192 * Update TX scheduler ring when transmitting an 802.11 frame (4965AGN and
4193 * 5000 adapters use a slightly different format).
4196 iwn4965_update_sched(struct iwn_softc *sc, int qid, int idx, uint8_t id,
4199 uint16_t *w = &sc->sched[qid * IWN4965_SCHED_COUNT + idx];
4201 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
4203 *w = htole16(len + 8);
4204 bus_dmamap_sync(sc->sched_dma.tag, sc->sched_dma.map,
4205 BUS_DMASYNC_PREWRITE);
4206 if (idx < IWN_SCHED_WINSZ) {
4207 *(w + IWN_TX_RING_COUNT) = *w;
4208 bus_dmamap_sync(sc->sched_dma.tag, sc->sched_dma.map,
4209 BUS_DMASYNC_PREWRITE);
4214 iwn5000_update_sched(struct iwn_softc *sc, int qid, int idx, uint8_t id,
4217 uint16_t *w = &sc->sched[qid * IWN5000_SCHED_COUNT + idx];
4219 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
4221 *w = htole16(id << 12 | (len + 8));
4222 bus_dmamap_sync(sc->sched_dma.tag, sc->sched_dma.map,
4223 BUS_DMASYNC_PREWRITE);
4224 if (idx < IWN_SCHED_WINSZ) {
4225 *(w + IWN_TX_RING_COUNT) = *w;
4226 bus_dmamap_sync(sc->sched_dma.tag, sc->sched_dma.map,
4227 BUS_DMASYNC_PREWRITE);
4233 iwn5000_reset_sched(struct iwn_softc *sc, int qid, int idx)
4235 uint16_t *w = &sc->sched[qid * IWN5000_SCHED_COUNT + idx];
4237 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
4239 *w = (*w & htole16(0xf000)) | htole16(1);
4240 bus_dmamap_sync(sc->sched_dma.tag, sc->sched_dma.map,
4241 BUS_DMASYNC_PREWRITE);
4242 if (idx < IWN_SCHED_WINSZ) {
4243 *(w + IWN_TX_RING_COUNT) = *w;
4244 bus_dmamap_sync(sc->sched_dma.tag, sc->sched_dma.map,
4245 BUS_DMASYNC_PREWRITE);
4251 * Check whether OFDM 11g protection will be enabled for the given rate.
4253 * The original driver code only enabled protection for OFDM rates.
4254 * It didn't check to see whether it was operating in 11a or 11bg mode.
4257 iwn_check_rate_needs_protection(struct iwn_softc *sc,
4258 struct ieee80211vap *vap, uint8_t rate)
4260 struct ieee80211com *ic = vap->iv_ic;
4263 * Not in 2GHz mode? Then there's no need to enable OFDM
4266 if (! IEEE80211_IS_CHAN_2GHZ(ic->ic_curchan)) {
4271 * 11bg protection not enabled? Then don't use it.
4273 if ((ic->ic_flags & IEEE80211_F_USEPROT) == 0)
4277 * If it's an 11n rate - no protection.
4278 * We'll do it via a specific 11n check.
4280 if (rate & IEEE80211_RATE_MCS) {
4285 * Do a rate table lookup. If the PHY is CCK,
4286 * don't do protection.
4288 if (ieee80211_rate2phytype(ic->ic_rt, rate) == IEEE80211_T_CCK)
4292 * Yup, enable protection.
4298 * return a value between 0 and IWN_MAX_TX_RETRIES-1 as an index into
4299 * the link quality table that reflects this particular entry.
4302 iwn_tx_rate_to_linkq_offset(struct iwn_softc *sc, struct ieee80211_node *ni,
4305 struct ieee80211_rateset *rs;
4312 * Figure out if we're using 11n or not here.
4314 if (IEEE80211_IS_CHAN_HT(ni->ni_chan) && ni->ni_htrates.rs_nrates > 0)
4320 * Use the correct rate table.
4323 rs = (struct ieee80211_rateset *) &ni->ni_htrates;
4324 nr = ni->ni_htrates.rs_nrates;
4331 * Find the relevant link quality entry in the table.
4333 for (i = 0; i < nr && i < IWN_MAX_TX_RETRIES - 1 ; i++) {
4335 * The link quality table index starts at 0 == highest
4336 * rate, so we walk the rate table backwards.
4338 cmp_rate = rs->rs_rates[(nr - 1) - i];
4339 if (rate & IEEE80211_RATE_MCS)
4340 cmp_rate |= IEEE80211_RATE_MCS;
4343 DPRINTF(sc, IWN_DEBUG_XMIT, "%s: idx %d: nr=%d, rate=0x%02x, rateentry=0x%02x\n",
4351 if (cmp_rate == rate)
4355 /* Failed? Start at the end */
4356 return (IWN_MAX_TX_RETRIES - 1);
4360 iwn_tx_data(struct iwn_softc *sc, struct mbuf *m, struct ieee80211_node *ni)
4362 struct iwn_ops *ops = &sc->ops;
4363 const struct ieee80211_txparam *tp;
4364 struct ieee80211vap *vap = ni->ni_vap;
4365 struct ieee80211com *ic = ni->ni_ic;
4366 struct iwn_node *wn = (void *)ni;
4367 struct iwn_tx_ring *ring;
4368 struct iwn_tx_desc *desc;
4369 struct iwn_tx_data *data;
4370 struct iwn_tx_cmd *cmd;
4371 struct iwn_cmd_data *tx;
4372 struct ieee80211_frame *wh;
4373 struct ieee80211_key *k = NULL;
4378 bus_dma_segment_t *seg, segs[IWN_MAX_SCATTER];
4380 int ac, i, totlen, error, pad, nsegs = 0, rate;
4382 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
4384 IWN_LOCK_ASSERT(sc);
4386 wh = mtod(m, struct ieee80211_frame *);
4387 hdrlen = ieee80211_anyhdrsize(wh);
4388 type = wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK;
4390 /* Select EDCA Access Category and TX ring for this frame. */
4391 if (IEEE80211_QOS_HAS_SEQ(wh)) {
4392 qos = ((const struct ieee80211_qosframe *)wh)->i_qos[0];
4393 tid = qos & IEEE80211_QOS_TID;
4398 ac = M_WME_GETAC(m);
4399 if (m->m_flags & M_AMPDU_MPDU) {
4401 struct ieee80211_tx_ampdu *tap = &ni->ni_tx_ampdu[ac];
4403 if (!IEEE80211_AMPDU_RUNNING(tap)) {
4408 * Queue this frame to the hardware ring that we've
4409 * negotiated AMPDU TX on.
4411 * Note that the sequence number must match the TX slot
4414 ac = *(int *)tap->txa_private;
4415 seqno = ni->ni_txseqs[tid];
4416 *(uint16_t *)wh->i_seq =
4417 htole16(seqno << IEEE80211_SEQ_SEQ_SHIFT);
4418 ring = &sc->txq[ac];
4419 if ((seqno % 256) != ring->cur) {
4420 device_printf(sc->sc_dev,
4421 "%s: m=%p: seqno (%d) (%d) != ring index (%d) !\n",
4428 ni->ni_txseqs[tid]++;
4430 ring = &sc->txq[ac];
4431 desc = &ring->desc[ring->cur];
4432 data = &ring->data[ring->cur];
4434 /* Choose a TX rate index. */
4435 tp = &vap->iv_txparms[ieee80211_chan2mode(ni->ni_chan)];
4436 if (type == IEEE80211_FC0_TYPE_MGT)
4437 rate = tp->mgmtrate;
4438 else if (IEEE80211_IS_MULTICAST(wh->i_addr1))
4439 rate = tp->mcastrate;
4440 else if (tp->ucastrate != IEEE80211_FIXED_RATE_NONE)
4441 rate = tp->ucastrate;
4442 else if (m->m_flags & M_EAPOL)
4443 rate = tp->mgmtrate;
4445 /* XXX pass pktlen */
4446 (void) ieee80211_ratectl_rate(ni, NULL, 0);
4447 rate = ni->ni_txrate;
4450 /* Encrypt the frame if need be. */
4451 if (wh->i_fc[1] & IEEE80211_FC1_PROTECTED) {
4452 /* Retrieve key for TX. */
4453 k = ieee80211_crypto_encap(ni, m);
4457 /* 802.11 header may have moved. */
4458 wh = mtod(m, struct ieee80211_frame *);
4460 totlen = m->m_pkthdr.len;
4462 if (ieee80211_radiotap_active_vap(vap)) {
4463 struct iwn_tx_radiotap_header *tap = &sc->sc_txtap;
4466 tap->wt_rate = rate;
4468 tap->wt_flags |= IEEE80211_RADIOTAP_F_WEP;
4470 ieee80211_radiotap_tx(vap, m);
4473 /* Prepare TX firmware command. */
4474 cmd = &ring->cmd[ring->cur];
4475 cmd->code = IWN_CMD_TX_DATA;
4477 cmd->qid = ring->qid;
4478 cmd->idx = ring->cur;
4480 tx = (struct iwn_cmd_data *)cmd->data;
4481 /* NB: No need to clear tx, all fields are reinitialized here. */
4482 tx->scratch = 0; /* clear "scratch" area */
4485 if (!IEEE80211_IS_MULTICAST(wh->i_addr1)) {
4486 /* Unicast frame, check if an ACK is expected. */
4487 if (!qos || (qos & IEEE80211_QOS_ACKPOLICY) !=
4488 IEEE80211_QOS_ACKPOLICY_NOACK)
4489 flags |= IWN_TX_NEED_ACK;
4492 (IEEE80211_FC0_TYPE_MASK | IEEE80211_FC0_SUBTYPE_MASK)) ==
4493 (IEEE80211_FC0_TYPE_CTL | IEEE80211_FC0_SUBTYPE_BAR))
4494 flags |= IWN_TX_IMM_BA; /* Cannot happen yet. */
4496 if (wh->i_fc[1] & IEEE80211_FC1_MORE_FRAG)
4497 flags |= IWN_TX_MORE_FRAG; /* Cannot happen yet. */
4499 /* Check if frame must be protected using RTS/CTS or CTS-to-self. */
4500 if (!IEEE80211_IS_MULTICAST(wh->i_addr1)) {
4501 /* NB: Group frames are sent using CCK in 802.11b/g. */
4502 if (totlen + IEEE80211_CRC_LEN > vap->iv_rtsthreshold) {
4503 flags |= IWN_TX_NEED_RTS;
4504 } else if (iwn_check_rate_needs_protection(sc, vap, rate)) {
4505 if (ic->ic_protmode == IEEE80211_PROT_CTSONLY)
4506 flags |= IWN_TX_NEED_CTS;
4507 else if (ic->ic_protmode == IEEE80211_PROT_RTSCTS)
4508 flags |= IWN_TX_NEED_RTS;
4509 } else if ((rate & IEEE80211_RATE_MCS) &&
4510 (ic->ic_htprotmode == IEEE80211_PROT_RTSCTS)) {
4511 flags |= IWN_TX_NEED_RTS;
4514 /* XXX HT protection? */
4516 if (flags & (IWN_TX_NEED_RTS | IWN_TX_NEED_CTS)) {
4517 if (sc->hw_type != IWN_HW_REV_TYPE_4965) {
4518 /* 5000 autoselects RTS/CTS or CTS-to-self. */
4519 flags &= ~(IWN_TX_NEED_RTS | IWN_TX_NEED_CTS);
4520 flags |= IWN_TX_NEED_PROTECTION;
4522 flags |= IWN_TX_FULL_TXOP;
4526 if (IEEE80211_IS_MULTICAST(wh->i_addr1) ||
4527 type != IEEE80211_FC0_TYPE_DATA)
4528 tx->id = sc->broadcast_id;
4532 if (type == IEEE80211_FC0_TYPE_MGT) {
4533 uint8_t subtype = wh->i_fc[0] & IEEE80211_FC0_SUBTYPE_MASK;
4535 /* Tell HW to set timestamp in probe responses. */
4536 if (subtype == IEEE80211_FC0_SUBTYPE_PROBE_RESP)
4537 flags |= IWN_TX_INSERT_TSTAMP;
4538 if (subtype == IEEE80211_FC0_SUBTYPE_ASSOC_REQ ||
4539 subtype == IEEE80211_FC0_SUBTYPE_REASSOC_REQ)
4540 tx->timeout = htole16(3);
4542 tx->timeout = htole16(2);
4544 tx->timeout = htole16(0);
4547 /* First segment length must be a multiple of 4. */
4548 flags |= IWN_TX_NEED_PADDING;
4549 pad = 4 - (hdrlen & 3);
4553 tx->len = htole16(totlen);
4555 tx->rts_ntries = 60;
4556 tx->data_ntries = 15;
4557 tx->lifetime = htole32(IWN_LIFETIME_INFINITE);
4558 tx->rate = iwn_rate_to_plcp(sc, ni, rate);
4559 if (tx->id == sc->broadcast_id) {
4560 /* Group or management frame. */
4563 tx->linkq = iwn_tx_rate_to_linkq_offset(sc, ni, rate);
4564 flags |= IWN_TX_LINKQ; /* enable MRR */
4567 /* Set physical address of "scratch area". */
4568 tx->loaddr = htole32(IWN_LOADDR(data->scratch_paddr));
4569 tx->hiaddr = IWN_HIADDR(data->scratch_paddr);
4571 /* Copy 802.11 header in TX command. */
4572 memcpy((uint8_t *)(tx + 1), wh, hdrlen);
4574 /* Trim 802.11 header. */
4577 tx->flags = htole32(flags);
4579 error = bus_dmamap_load_mbuf_sg(ring->data_dmat, data->map, m, segs,
4580 &nsegs, BUS_DMA_NOWAIT);
4582 if (error != EFBIG) {
4583 device_printf(sc->sc_dev,
4584 "%s: can't map mbuf (error %d)\n", __func__, error);
4587 /* Too many DMA segments, linearize mbuf. */
4588 m1 = m_collapse(m, M_NOWAIT, IWN_MAX_SCATTER - 1);
4590 device_printf(sc->sc_dev,
4591 "%s: could not defrag mbuf\n", __func__);
4596 error = bus_dmamap_load_mbuf_sg(ring->data_dmat, data->map, m,
4597 segs, &nsegs, BUS_DMA_NOWAIT);
4599 device_printf(sc->sc_dev,
4600 "%s: can't map mbuf (error %d)\n", __func__, error);
4608 DPRINTF(sc, IWN_DEBUG_XMIT,
4609 "%s: qid %d idx %d len %d nsegs %d flags 0x%08x rate 0x%04x plcp 0x%08x\n",
4619 /* Fill TX descriptor. */
4622 desc->nsegs += nsegs;
4623 /* First DMA segment is used by the TX command. */
4624 desc->segs[0].addr = htole32(IWN_LOADDR(data->cmd_paddr));
4625 desc->segs[0].len = htole16(IWN_HIADDR(data->cmd_paddr) |
4626 (4 + sizeof (*tx) + hdrlen + pad) << 4);
4627 /* Other DMA segments are for data payload. */
4629 for (i = 1; i <= nsegs; i++) {
4630 desc->segs[i].addr = htole32(IWN_LOADDR(seg->ds_addr));
4631 desc->segs[i].len = htole16(IWN_HIADDR(seg->ds_addr) |
4636 bus_dmamap_sync(ring->data_dmat, data->map, BUS_DMASYNC_PREWRITE);
4637 bus_dmamap_sync(ring->cmd_dma.tag, ring->cmd_dma.map,
4638 BUS_DMASYNC_PREWRITE);
4639 bus_dmamap_sync(ring->desc_dma.tag, ring->desc_dma.map,
4640 BUS_DMASYNC_PREWRITE);
4642 /* Update TX scheduler. */
4643 if (ring->qid >= sc->firstaggqueue)
4644 ops->update_sched(sc, ring->qid, ring->cur, tx->id, totlen);
4647 ring->cur = (ring->cur + 1) % IWN_TX_RING_COUNT;
4648 IWN_WRITE(sc, IWN_HBUS_TARG_WRPTR, ring->qid << 8 | ring->cur);
4650 /* Mark TX ring as full if we reach a certain threshold. */
4651 if (++ring->queued > IWN_TX_RING_HIMARK)
4652 sc->qfullmsk |= 1 << ring->qid;
4654 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
4660 iwn_tx_data_raw(struct iwn_softc *sc, struct mbuf *m,
4661 struct ieee80211_node *ni, const struct ieee80211_bpf_params *params)
4663 struct iwn_ops *ops = &sc->ops;
4664 struct ieee80211vap *vap = ni->ni_vap;
4665 struct iwn_tx_cmd *cmd;
4666 struct iwn_cmd_data *tx;
4667 struct ieee80211_frame *wh;
4668 struct iwn_tx_ring *ring;
4669 struct iwn_tx_desc *desc;
4670 struct iwn_tx_data *data;
4672 bus_dma_segment_t *seg, segs[IWN_MAX_SCATTER];
4675 int ac, totlen, error, pad, nsegs = 0, i, rate;
4678 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
4680 IWN_LOCK_ASSERT(sc);
4682 wh = mtod(m, struct ieee80211_frame *);
4683 hdrlen = ieee80211_anyhdrsize(wh);
4684 type = wh->i_fc[0] & IEEE80211_FC0_TYPE_MASK;
4686 ac = params->ibp_pri & 3;
4688 ring = &sc->txq[ac];
4689 desc = &ring->desc[ring->cur];
4690 data = &ring->data[ring->cur];
4692 /* Choose a TX rate. */
4693 rate = params->ibp_rate0;
4694 totlen = m->m_pkthdr.len;
4696 /* Prepare TX firmware command. */
4697 cmd = &ring->cmd[ring->cur];
4698 cmd->code = IWN_CMD_TX_DATA;
4700 cmd->qid = ring->qid;
4701 cmd->idx = ring->cur;
4703 tx = (struct iwn_cmd_data *)cmd->data;
4704 /* NB: No need to clear tx, all fields are reinitialized here. */
4705 tx->scratch = 0; /* clear "scratch" area */
4708 if ((params->ibp_flags & IEEE80211_BPF_NOACK) == 0)
4709 flags |= IWN_TX_NEED_ACK;
4710 if (params->ibp_flags & IEEE80211_BPF_RTS) {
4711 if (sc->hw_type != IWN_HW_REV_TYPE_4965) {
4712 /* 5000 autoselects RTS/CTS or CTS-to-self. */
4713 flags &= ~IWN_TX_NEED_RTS;
4714 flags |= IWN_TX_NEED_PROTECTION;
4716 flags |= IWN_TX_NEED_RTS | IWN_TX_FULL_TXOP;
4718 if (params->ibp_flags & IEEE80211_BPF_CTS) {
4719 if (sc->hw_type != IWN_HW_REV_TYPE_4965) {
4720 /* 5000 autoselects RTS/CTS or CTS-to-self. */
4721 flags &= ~IWN_TX_NEED_CTS;
4722 flags |= IWN_TX_NEED_PROTECTION;
4724 flags |= IWN_TX_NEED_CTS | IWN_TX_FULL_TXOP;
4726 if (type == IEEE80211_FC0_TYPE_MGT) {
4727 uint8_t subtype = wh->i_fc[0] & IEEE80211_FC0_SUBTYPE_MASK;
4729 /* Tell HW to set timestamp in probe responses. */
4730 if (subtype == IEEE80211_FC0_SUBTYPE_PROBE_RESP)
4731 flags |= IWN_TX_INSERT_TSTAMP;
4733 if (subtype == IEEE80211_FC0_SUBTYPE_ASSOC_REQ ||
4734 subtype == IEEE80211_FC0_SUBTYPE_REASSOC_REQ)
4735 tx->timeout = htole16(3);
4737 tx->timeout = htole16(2);
4739 tx->timeout = htole16(0);
4742 /* First segment length must be a multiple of 4. */
4743 flags |= IWN_TX_NEED_PADDING;
4744 pad = 4 - (hdrlen & 3);
4748 if (ieee80211_radiotap_active_vap(vap)) {
4749 struct iwn_tx_radiotap_header *tap = &sc->sc_txtap;
4752 tap->wt_rate = rate;
4754 ieee80211_radiotap_tx(vap, m);
4757 tx->len = htole16(totlen);
4759 tx->id = sc->broadcast_id;
4760 tx->rts_ntries = params->ibp_try1;
4761 tx->data_ntries = params->ibp_try0;
4762 tx->lifetime = htole32(IWN_LIFETIME_INFINITE);
4763 tx->rate = iwn_rate_to_plcp(sc, ni, rate);
4765 /* Group or management frame. */
4768 /* Set physical address of "scratch area". */
4769 tx->loaddr = htole32(IWN_LOADDR(data->scratch_paddr));
4770 tx->hiaddr = IWN_HIADDR(data->scratch_paddr);
4772 /* Copy 802.11 header in TX command. */
4773 memcpy((uint8_t *)(tx + 1), wh, hdrlen);
4775 /* Trim 802.11 header. */
4778 tx->flags = htole32(flags);
4780 error = bus_dmamap_load_mbuf_sg(ring->data_dmat, data->map, m, segs,
4781 &nsegs, BUS_DMA_NOWAIT);
4783 if (error != EFBIG) {
4784 device_printf(sc->sc_dev,
4785 "%s: can't map mbuf (error %d)\n", __func__, error);
4788 /* Too many DMA segments, linearize mbuf. */
4789 m1 = m_collapse(m, M_NOWAIT, IWN_MAX_SCATTER - 1);
4791 device_printf(sc->sc_dev,
4792 "%s: could not defrag mbuf\n", __func__);
4797 error = bus_dmamap_load_mbuf_sg(ring->data_dmat, data->map, m,
4798 segs, &nsegs, BUS_DMA_NOWAIT);
4800 device_printf(sc->sc_dev,
4801 "%s: can't map mbuf (error %d)\n", __func__, error);
4809 DPRINTF(sc, IWN_DEBUG_XMIT, "%s: qid %d idx %d len %d nsegs %d\n",
4810 __func__, ring->qid, ring->cur, m->m_pkthdr.len, nsegs);
4812 /* Fill TX descriptor. */
4815 desc->nsegs += nsegs;
4816 /* First DMA segment is used by the TX command. */
4817 desc->segs[0].addr = htole32(IWN_LOADDR(data->cmd_paddr));
4818 desc->segs[0].len = htole16(IWN_HIADDR(data->cmd_paddr) |
4819 (4 + sizeof (*tx) + hdrlen + pad) << 4);
4820 /* Other DMA segments are for data payload. */
4822 for (i = 1; i <= nsegs; i++) {
4823 desc->segs[i].addr = htole32(IWN_LOADDR(seg->ds_addr));
4824 desc->segs[i].len = htole16(IWN_HIADDR(seg->ds_addr) |
4829 bus_dmamap_sync(ring->data_dmat, data->map, BUS_DMASYNC_PREWRITE);
4830 bus_dmamap_sync(ring->cmd_dma.tag, ring->cmd_dma.map,
4831 BUS_DMASYNC_PREWRITE);
4832 bus_dmamap_sync(ring->desc_dma.tag, ring->desc_dma.map,
4833 BUS_DMASYNC_PREWRITE);
4835 /* Update TX scheduler. */
4836 if (ring->qid >= sc->firstaggqueue)
4837 ops->update_sched(sc, ring->qid, ring->cur, tx->id, totlen);
4840 ring->cur = (ring->cur + 1) % IWN_TX_RING_COUNT;
4841 IWN_WRITE(sc, IWN_HBUS_TARG_WRPTR, ring->qid << 8 | ring->cur);
4843 /* Mark TX ring as full if we reach a certain threshold. */
4844 if (++ring->queued > IWN_TX_RING_HIMARK)
4845 sc->qfullmsk |= 1 << ring->qid;
4847 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
4853 iwn_xmit_task(void *arg0, int pending)
4855 struct iwn_softc *sc = arg0;
4856 struct ieee80211_node *ni;
4859 struct ieee80211_bpf_params p;
4862 DPRINTF(sc, IWN_DEBUG_XMIT, "%s: called\n", __func__);
4866 * Dequeue frames, attempt to transmit,
4867 * then disable beaconwait when we're done.
4869 while ((m = mbufq_dequeue(&sc->sc_xmit_queue)) != NULL) {
4871 ni = (struct ieee80211_node *)m->m_pkthdr.rcvif;
4873 /* Get xmit params if appropriate */
4874 if (ieee80211_get_xmit_params(m, &p) == 0)
4877 DPRINTF(sc, IWN_DEBUG_XMIT, "%s: m=%p, have_p=%d\n",
4878 __func__, m, have_p);
4880 /* If we have xmit params, use them */
4882 error = iwn_tx_data_raw(sc, m, ni, &p);
4884 error = iwn_tx_data(sc, m, ni);
4887 if_inc_counter(ni->ni_vap->iv_ifp,
4888 IFCOUNTER_OERRORS, 1);
4889 ieee80211_free_node(ni);
4894 sc->sc_beacon_wait = 0;
4899 * raw frame xmit - free node/reference if failed.
4902 iwn_raw_xmit(struct ieee80211_node *ni, struct mbuf *m,
4903 const struct ieee80211_bpf_params *params)
4905 struct ieee80211com *ic = ni->ni_ic;
4906 struct iwn_softc *sc = ic->ic_softc;
4909 DPRINTF(sc, IWN_DEBUG_XMIT | IWN_DEBUG_TRACE, "->%s begin\n", __func__);
4912 if ((sc->sc_flags & IWN_FLAG_RUNNING) == 0) {
4918 /* queue frame if we have to */
4919 if (sc->sc_beacon_wait) {
4920 if (iwn_xmit_queue_enqueue(sc, m) != 0) {
4925 /* Queued, so just return OK */
4930 if (params == NULL) {
4932 * Legacy path; interpret frame contents to decide
4933 * precisely how to send the frame.
4935 error = iwn_tx_data(sc, m, ni);
4938 * Caller supplied explicit parameters to use in
4939 * sending the frame.
4941 error = iwn_tx_data_raw(sc, m, ni, params);
4944 sc->sc_tx_timer = 5;
4950 DPRINTF(sc, IWN_DEBUG_TRACE | IWN_DEBUG_XMIT, "->%s: end\n",__func__);
4956 * transmit - don't free mbuf if failed; don't free node ref if failed.
4959 iwn_transmit(struct ieee80211com *ic, struct mbuf *m)
4961 struct iwn_softc *sc = ic->ic_softc;
4962 struct ieee80211_node *ni;
4965 ni = (struct ieee80211_node *)m->m_pkthdr.rcvif;
4968 if ((sc->sc_flags & IWN_FLAG_RUNNING) == 0 || sc->sc_beacon_wait) {
4978 error = iwn_tx_data(sc, m, ni);
4980 sc->sc_tx_timer = 5;
4986 iwn_scan_timeout(void *arg)
4988 struct iwn_softc *sc = arg;
4989 struct ieee80211com *ic = &sc->sc_ic;
4991 ic_printf(ic, "scan timeout\n");
4992 ieee80211_restart_all(ic);
4996 iwn_watchdog(void *arg)
4998 struct iwn_softc *sc = arg;
4999 struct ieee80211com *ic = &sc->sc_ic;
5001 IWN_LOCK_ASSERT(sc);
5003 KASSERT(sc->sc_flags & IWN_FLAG_RUNNING, ("not running"));
5005 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5007 if (sc->sc_tx_timer > 0) {
5008 if (--sc->sc_tx_timer == 0) {
5009 ic_printf(ic, "device timeout\n");
5010 ieee80211_restart_all(ic);
5014 callout_reset(&sc->watchdog_to, hz, iwn_watchdog, sc);
5018 iwn_cdev_open(struct cdev *dev, int flags, int type, struct thread *td)
5025 iwn_cdev_close(struct cdev *dev, int flags, int type, struct thread *td)
5032 iwn_cdev_ioctl(struct cdev *dev, unsigned long cmd, caddr_t data, int fflag,
5036 struct iwn_softc *sc = dev->si_drv1;
5037 struct iwn_ioctl_data *d;
5039 rc = priv_check(td, PRIV_DRIVER);
5045 d = (struct iwn_ioctl_data *) data;
5047 /* XXX validate permissions/memory/etc? */
5048 rc = copyout(&sc->last_stat, d->dst_addr, sizeof(struct iwn_stats));
5053 memset(&sc->last_stat, 0, sizeof(struct iwn_stats));
5064 iwn_ioctl(struct ieee80211com *ic, u_long cmd, void *data)
5071 iwn_parent(struct ieee80211com *ic)
5073 struct iwn_softc *sc = ic->ic_softc;
5074 struct ieee80211vap *vap = TAILQ_FIRST(&ic->ic_vaps);
5075 int startall = 0, stop = 0;
5078 if (ic->ic_nrunning > 0) {
5079 if (!(sc->sc_flags & IWN_FLAG_RUNNING)) {
5080 iwn_init_locked(sc);
5081 if (IWN_READ(sc, IWN_GP_CNTRL) & IWN_GP_CNTRL_RFKILL)
5086 } else if (sc->sc_flags & IWN_FLAG_RUNNING)
5087 iwn_stop_locked(sc);
5090 ieee80211_start_all(ic);
5091 else if (vap != NULL && stop)
5092 ieee80211_stop(vap);
5096 * Send a command to the firmware.
5099 iwn_cmd(struct iwn_softc *sc, int code, const void *buf, int size, int async)
5101 struct iwn_tx_ring *ring;
5102 struct iwn_tx_desc *desc;
5103 struct iwn_tx_data *data;
5104 struct iwn_tx_cmd *cmd;
5110 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
5113 IWN_LOCK_ASSERT(sc);
5115 if (sc->sc_flags & IWN_FLAG_PAN_SUPPORT)
5116 cmd_queue_num = IWN_PAN_CMD_QUEUE;
5118 cmd_queue_num = IWN_CMD_QUEUE_NUM;
5120 ring = &sc->txq[cmd_queue_num];
5121 desc = &ring->desc[ring->cur];
5122 data = &ring->data[ring->cur];
5125 if (size > sizeof cmd->data) {
5126 /* Command is too large to fit in a descriptor. */
5127 if (totlen > MCLBYTES)
5129 m = m_getjcl(M_NOWAIT, MT_DATA, M_PKTHDR, MJUMPAGESIZE);
5132 cmd = mtod(m, struct iwn_tx_cmd *);
5133 error = bus_dmamap_load(ring->data_dmat, data->map, cmd,
5134 totlen, iwn_dma_map_addr, &paddr, BUS_DMA_NOWAIT);
5141 cmd = &ring->cmd[ring->cur];
5142 paddr = data->cmd_paddr;
5147 cmd->qid = ring->qid;
5148 cmd->idx = ring->cur;
5149 memcpy(cmd->data, buf, size);
5152 desc->segs[0].addr = htole32(IWN_LOADDR(paddr));
5153 desc->segs[0].len = htole16(IWN_HIADDR(paddr) | totlen << 4);
5155 DPRINTF(sc, IWN_DEBUG_CMD, "%s: %s (0x%x) flags %d qid %d idx %d\n",
5156 __func__, iwn_intr_str(cmd->code), cmd->code,
5157 cmd->flags, cmd->qid, cmd->idx);
5159 if (size > sizeof cmd->data) {
5160 bus_dmamap_sync(ring->data_dmat, data->map,
5161 BUS_DMASYNC_PREWRITE);
5163 bus_dmamap_sync(ring->cmd_dma.tag, ring->cmd_dma.map,
5164 BUS_DMASYNC_PREWRITE);
5166 bus_dmamap_sync(ring->desc_dma.tag, ring->desc_dma.map,
5167 BUS_DMASYNC_PREWRITE);
5169 /* Kick command ring. */
5170 ring->cur = (ring->cur + 1) % IWN_TX_RING_COUNT;
5171 IWN_WRITE(sc, IWN_HBUS_TARG_WRPTR, ring->qid << 8 | ring->cur);
5173 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
5175 return async ? 0 : msleep(desc, &sc->sc_mtx, PCATCH, "iwncmd", hz);
5179 iwn4965_add_node(struct iwn_softc *sc, struct iwn_node_info *node, int async)
5181 struct iwn4965_node_info hnode;
5184 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5187 * We use the node structure for 5000 Series internally (it is
5188 * a superset of the one for 4965AGN). We thus copy the common
5189 * fields before sending the command.
5191 src = (caddr_t)node;
5192 dst = (caddr_t)&hnode;
5193 memcpy(dst, src, 48);
5194 /* Skip TSC, RX MIC and TX MIC fields from ``src''. */
5195 memcpy(dst + 48, src + 72, 20);
5196 return iwn_cmd(sc, IWN_CMD_ADD_NODE, &hnode, sizeof hnode, async);
5200 iwn5000_add_node(struct iwn_softc *sc, struct iwn_node_info *node, int async)
5203 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5205 /* Direct mapping. */
5206 return iwn_cmd(sc, IWN_CMD_ADD_NODE, node, sizeof (*node), async);
5210 iwn_set_link_quality(struct iwn_softc *sc, struct ieee80211_node *ni)
5212 struct iwn_node *wn = (void *)ni;
5213 struct ieee80211_rateset *rs;
5214 struct iwn_cmd_link_quality linkq;
5215 int i, rate, txrate;
5218 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
5220 memset(&linkq, 0, sizeof linkq);
5222 linkq.antmsk_1stream = iwn_get_1stream_tx_antmask(sc);
5223 linkq.antmsk_2stream = iwn_get_2stream_tx_antmask(sc);
5225 linkq.ampdu_max = 32; /* XXX negotiated? */
5226 linkq.ampdu_threshold = 3;
5227 linkq.ampdu_limit = htole16(4000); /* 4ms */
5229 DPRINTF(sc, IWN_DEBUG_XMIT,
5230 "%s: 1stream antenna=0x%02x, 2stream antenna=0x%02x, ntxstreams=%d\n",
5232 linkq.antmsk_1stream,
5233 linkq.antmsk_2stream,
5237 * Are we using 11n rates? Ensure the channel is
5238 * 11n _and_ we have some 11n rates, or don't
5241 if (IEEE80211_IS_CHAN_HT(ni->ni_chan) && ni->ni_htrates.rs_nrates > 0) {
5242 rs = (struct ieee80211_rateset *) &ni->ni_htrates;
5249 /* Start at highest available bit-rate. */
5251 * XXX this is all very dirty!
5254 txrate = ni->ni_htrates.rs_nrates - 1;
5256 txrate = rs->rs_nrates - 1;
5257 for (i = 0; i < IWN_MAX_TX_RETRIES; i++) {
5261 * XXX TODO: ensure the last two slots are the two lowest
5262 * rate entries, just for now.
5264 if (i == 14 || i == 15)
5268 rate = IEEE80211_RATE_MCS | rs->rs_rates[txrate];
5270 rate = IEEE80211_RV(rs->rs_rates[txrate]);
5272 /* Do rate -> PLCP config mapping */
5273 plcp = iwn_rate_to_plcp(sc, ni, rate);
5274 linkq.retry[i] = plcp;
5275 DPRINTF(sc, IWN_DEBUG_XMIT,
5276 "%s: i=%d, txrate=%d, rate=0x%02x, plcp=0x%08x\n",
5284 * The mimo field is an index into the table which
5285 * indicates the first index where it and subsequent entries
5286 * will not be using MIMO.
5288 * Since we're filling linkq from 0..15 and we're filling
5289 * from the highest MCS rates to the lowest rates, if we
5290 * _are_ doing a dual-stream rate, set mimo to idx+1 (ie,
5291 * the next entry.) That way if the next entry is a non-MIMO
5292 * entry, we're already pointing at it.
5294 if ((le32toh(plcp) & IWN_RFLAG_MCS) &&
5295 IEEE80211_RV(le32toh(plcp)) > 7)
5298 /* Next retry at immediate lower bit-rate. */
5303 * If we reached the end of the list and indeed we hit
5304 * all MIMO rates (eg 5300 doing MCS23-15) then yes,
5305 * set mimo to 15. Setting it to 16 panics the firmware.
5307 if (linkq.mimo > 15)
5310 DPRINTF(sc, IWN_DEBUG_XMIT, "%s: mimo = %d\n", __func__, linkq.mimo);
5312 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
5314 return iwn_cmd(sc, IWN_CMD_LINK_QUALITY, &linkq, sizeof linkq, 1);
5318 * Broadcast node is used to send group-addressed and management frames.
5321 iwn_add_broadcast_node(struct iwn_softc *sc, int async)
5323 struct iwn_ops *ops = &sc->ops;
5324 struct ieee80211com *ic = &sc->sc_ic;
5325 struct iwn_node_info node;
5326 struct iwn_cmd_link_quality linkq;
5330 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
5332 sc->rxon = &sc->rx_on[IWN_RXON_BSS_CTX];
5334 memset(&node, 0, sizeof node);
5335 IEEE80211_ADDR_COPY(node.macaddr, ieee80211broadcastaddr);
5336 node.id = sc->broadcast_id;
5337 DPRINTF(sc, IWN_DEBUG_RESET, "%s: adding broadcast node\n", __func__);
5338 if ((error = ops->add_node(sc, &node, async)) != 0)
5341 /* Use the first valid TX antenna. */
5342 txant = IWN_LSB(sc->txchainmask);
5344 memset(&linkq, 0, sizeof linkq);
5345 linkq.id = sc->broadcast_id;
5346 linkq.antmsk_1stream = iwn_get_1stream_tx_antmask(sc);
5347 linkq.antmsk_2stream = iwn_get_2stream_tx_antmask(sc);
5348 linkq.ampdu_max = 64;
5349 linkq.ampdu_threshold = 3;
5350 linkq.ampdu_limit = htole16(4000); /* 4ms */
5352 /* Use lowest mandatory bit-rate. */
5353 /* XXX rate table lookup? */
5354 if (IEEE80211_IS_CHAN_5GHZ(ic->ic_curchan))
5355 linkq.retry[0] = htole32(0xd);
5357 linkq.retry[0] = htole32(10 | IWN_RFLAG_CCK);
5358 linkq.retry[0] |= htole32(IWN_RFLAG_ANT(txant));
5359 /* Use same bit-rate for all TX retries. */
5360 for (i = 1; i < IWN_MAX_TX_RETRIES; i++) {
5361 linkq.retry[i] = linkq.retry[0];
5364 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
5366 return iwn_cmd(sc, IWN_CMD_LINK_QUALITY, &linkq, sizeof linkq, async);
5370 iwn_updateedca(struct ieee80211com *ic)
5372 #define IWN_EXP2(x) ((1 << (x)) - 1) /* CWmin = 2^ECWmin - 1 */
5373 struct iwn_softc *sc = ic->ic_softc;
5374 struct iwn_edca_params cmd;
5377 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
5379 memset(&cmd, 0, sizeof cmd);
5380 cmd.flags = htole32(IWN_EDCA_UPDATE);
5383 for (aci = 0; aci < WME_NUM_AC; aci++) {
5384 const struct wmeParams *ac =
5385 &ic->ic_wme.wme_chanParams.cap_wmeParams[aci];
5386 cmd.ac[aci].aifsn = ac->wmep_aifsn;
5387 cmd.ac[aci].cwmin = htole16(IWN_EXP2(ac->wmep_logcwmin));
5388 cmd.ac[aci].cwmax = htole16(IWN_EXP2(ac->wmep_logcwmax));
5389 cmd.ac[aci].txoplimit =
5390 htole16(IEEE80211_TXOP_TO_US(ac->wmep_txopLimit));
5392 IEEE80211_UNLOCK(ic);
5395 (void)iwn_cmd(sc, IWN_CMD_EDCA_PARAMS, &cmd, sizeof cmd, 1);
5398 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
5405 iwn_update_mcast(struct ieee80211com *ic)
5411 iwn_set_led(struct iwn_softc *sc, uint8_t which, uint8_t off, uint8_t on)
5413 struct iwn_cmd_led led;
5415 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5418 /* XXX don't set LEDs during scan? */
5419 if (sc->sc_is_scanning)
5423 /* Clear microcode LED ownership. */
5424 IWN_CLRBITS(sc, IWN_LED, IWN_LED_BSM_CTRL);
5427 led.unit = htole32(10000); /* on/off in unit of 100ms */
5430 (void)iwn_cmd(sc, IWN_CMD_SET_LED, &led, sizeof led, 1);
5434 * Set the critical temperature at which the firmware will stop the radio
5438 iwn_set_critical_temp(struct iwn_softc *sc)
5440 struct iwn_critical_temp crit;
5443 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5445 IWN_WRITE(sc, IWN_UCODE_GP1_CLR, IWN_UCODE_GP1_CTEMP_STOP_RF);
5447 if (sc->hw_type == IWN_HW_REV_TYPE_5150)
5448 temp = (IWN_CTOK(110) - sc->temp_off) * -5;
5449 else if (sc->hw_type == IWN_HW_REV_TYPE_4965)
5450 temp = IWN_CTOK(110);
5453 memset(&crit, 0, sizeof crit);
5454 crit.tempR = htole32(temp);
5455 DPRINTF(sc, IWN_DEBUG_RESET, "setting critical temp to %d\n", temp);
5456 return iwn_cmd(sc, IWN_CMD_SET_CRITICAL_TEMP, &crit, sizeof crit, 0);
5460 iwn_set_timing(struct iwn_softc *sc, struct ieee80211_node *ni)
5462 struct iwn_cmd_timing cmd;
5465 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5467 memset(&cmd, 0, sizeof cmd);
5468 memcpy(&cmd.tstamp, ni->ni_tstamp.data, sizeof (uint64_t));
5469 cmd.bintval = htole16(ni->ni_intval);
5470 cmd.lintval = htole16(10);
5472 /* Compute remaining time until next beacon. */
5473 val = (uint64_t)ni->ni_intval * IEEE80211_DUR_TU;
5474 mod = le64toh(cmd.tstamp) % val;
5475 cmd.binitval = htole32((uint32_t)(val - mod));
5477 DPRINTF(sc, IWN_DEBUG_RESET, "timing bintval=%u tstamp=%ju, init=%u\n",
5478 ni->ni_intval, le64toh(cmd.tstamp), (uint32_t)(val - mod));
5480 return iwn_cmd(sc, IWN_CMD_TIMING, &cmd, sizeof cmd, 1);
5484 iwn4965_power_calibration(struct iwn_softc *sc, int temp)
5486 struct ieee80211com *ic = &sc->sc_ic;
5488 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5490 /* Adjust TX power if need be (delta >= 3 degC). */
5491 DPRINTF(sc, IWN_DEBUG_CALIBRATE, "%s: temperature %d->%d\n",
5492 __func__, sc->temp, temp);
5493 if (abs(temp - sc->temp) >= 3) {
5494 /* Record temperature of last calibration. */
5496 (void)iwn4965_set_txpower(sc, ic->ic_bsschan, 1);
5501 * Set TX power for current channel (each rate has its own power settings).
5502 * This function takes into account the regulatory information from EEPROM,
5503 * the current temperature and the current voltage.
5506 iwn4965_set_txpower(struct iwn_softc *sc, struct ieee80211_channel *ch,
5509 /* Fixed-point arithmetic division using a n-bit fractional part. */
5510 #define fdivround(a, b, n) \
5511 ((((1 << n) * (a)) / (b) + (1 << n) / 2) / (1 << n))
5512 /* Linear interpolation. */
5513 #define interpolate(x, x1, y1, x2, y2, n) \
5514 ((y1) + fdivround(((int)(x) - (x1)) * ((y2) - (y1)), (x2) - (x1), n))
5516 static const int tdiv[IWN_NATTEN_GROUPS] = { 9, 8, 8, 8, 6 };
5517 struct iwn_ucode_info *uc = &sc->ucode_info;
5518 struct iwn4965_cmd_txpower cmd;
5519 struct iwn4965_eeprom_chan_samples *chans;
5520 const uint8_t *rf_gain, *dsp_gain;
5521 int32_t vdiff, tdiff;
5522 int i, c, grp, maxpwr;
5525 sc->rxon = &sc->rx_on[IWN_RXON_BSS_CTX];
5526 /* Retrieve current channel from last RXON. */
5527 chan = sc->rxon->chan;
5528 DPRINTF(sc, IWN_DEBUG_RESET, "setting TX power for channel %d\n",
5531 memset(&cmd, 0, sizeof cmd);
5532 cmd.band = IEEE80211_IS_CHAN_5GHZ(ch) ? 0 : 1;
5535 if (IEEE80211_IS_CHAN_5GHZ(ch)) {
5536 maxpwr = sc->maxpwr5GHz;
5537 rf_gain = iwn4965_rf_gain_5ghz;
5538 dsp_gain = iwn4965_dsp_gain_5ghz;
5540 maxpwr = sc->maxpwr2GHz;
5541 rf_gain = iwn4965_rf_gain_2ghz;
5542 dsp_gain = iwn4965_dsp_gain_2ghz;
5545 /* Compute voltage compensation. */
5546 vdiff = ((int32_t)le32toh(uc->volt) - sc->eeprom_voltage) / 7;
5551 DPRINTF(sc, IWN_DEBUG_CALIBRATE | IWN_DEBUG_TXPOW,
5552 "%s: voltage compensation=%d (UCODE=%d, EEPROM=%d)\n",
5553 __func__, vdiff, le32toh(uc->volt), sc->eeprom_voltage);
5555 /* Get channel attenuation group. */
5556 if (chan <= 20) /* 1-20 */
5558 else if (chan <= 43) /* 34-43 */
5560 else if (chan <= 70) /* 44-70 */
5562 else if (chan <= 124) /* 71-124 */
5566 DPRINTF(sc, IWN_DEBUG_CALIBRATE | IWN_DEBUG_TXPOW,
5567 "%s: chan %d, attenuation group=%d\n", __func__, chan, grp);
5569 /* Get channel sub-band. */
5570 for (i = 0; i < IWN_NBANDS; i++)
5571 if (sc->bands[i].lo != 0 &&
5572 sc->bands[i].lo <= chan && chan <= sc->bands[i].hi)
5574 if (i == IWN_NBANDS) /* Can't happen in real-life. */
5576 chans = sc->bands[i].chans;
5577 DPRINTF(sc, IWN_DEBUG_CALIBRATE | IWN_DEBUG_TXPOW,
5578 "%s: chan %d sub-band=%d\n", __func__, chan, i);
5580 for (c = 0; c < 2; c++) {
5581 uint8_t power, gain, temp;
5582 int maxchpwr, pwr, ridx, idx;
5584 power = interpolate(chan,
5585 chans[0].num, chans[0].samples[c][1].power,
5586 chans[1].num, chans[1].samples[c][1].power, 1);
5587 gain = interpolate(chan,
5588 chans[0].num, chans[0].samples[c][1].gain,
5589 chans[1].num, chans[1].samples[c][1].gain, 1);
5590 temp = interpolate(chan,
5591 chans[0].num, chans[0].samples[c][1].temp,
5592 chans[1].num, chans[1].samples[c][1].temp, 1);
5593 DPRINTF(sc, IWN_DEBUG_CALIBRATE | IWN_DEBUG_TXPOW,
5594 "%s: Tx chain %d: power=%d gain=%d temp=%d\n",
5595 __func__, c, power, gain, temp);
5597 /* Compute temperature compensation. */
5598 tdiff = ((sc->temp - temp) * 2) / tdiv[grp];
5599 DPRINTF(sc, IWN_DEBUG_CALIBRATE | IWN_DEBUG_TXPOW,
5600 "%s: temperature compensation=%d (current=%d, EEPROM=%d)\n",
5601 __func__, tdiff, sc->temp, temp);
5603 for (ridx = 0; ridx <= IWN_RIDX_MAX; ridx++) {
5604 /* Convert dBm to half-dBm. */
5605 maxchpwr = sc->maxpwr[chan] * 2;
5607 maxchpwr -= 6; /* MIMO 2T: -3dB */
5611 /* Adjust TX power based on rate. */
5612 if ((ridx % 8) == 5)
5613 pwr -= 15; /* OFDM48: -7.5dB */
5614 else if ((ridx % 8) == 6)
5615 pwr -= 17; /* OFDM54: -8.5dB */
5616 else if ((ridx % 8) == 7)
5617 pwr -= 20; /* OFDM60: -10dB */
5619 pwr -= 10; /* Others: -5dB */
5621 /* Do not exceed channel max TX power. */
5625 idx = gain - (pwr - power) - tdiff - vdiff;
5626 if ((ridx / 8) & 1) /* MIMO */
5627 idx += (int32_t)le32toh(uc->atten[grp][c]);
5630 idx += 9; /* 5GHz */
5631 if (ridx == IWN_RIDX_MAX)
5634 /* Make sure idx stays in a valid range. */
5637 else if (idx > IWN4965_MAX_PWR_INDEX)
5638 idx = IWN4965_MAX_PWR_INDEX;
5640 DPRINTF(sc, IWN_DEBUG_CALIBRATE | IWN_DEBUG_TXPOW,
5641 "%s: Tx chain %d, rate idx %d: power=%d\n",
5642 __func__, c, ridx, idx);
5643 cmd.power[ridx].rf_gain[c] = rf_gain[idx];
5644 cmd.power[ridx].dsp_gain[c] = dsp_gain[idx];
5648 DPRINTF(sc, IWN_DEBUG_CALIBRATE | IWN_DEBUG_TXPOW,
5649 "%s: set tx power for chan %d\n", __func__, chan);
5650 return iwn_cmd(sc, IWN_CMD_TXPOWER, &cmd, sizeof cmd, async);
5657 iwn5000_set_txpower(struct iwn_softc *sc, struct ieee80211_channel *ch,
5660 struct iwn5000_cmd_txpower cmd;
5663 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5666 * TX power calibration is handled automatically by the firmware
5669 memset(&cmd, 0, sizeof cmd);
5670 cmd.global_limit = 2 * IWN5000_TXPOWER_MAX_DBM; /* 16 dBm */
5671 cmd.flags = IWN5000_TXPOWER_NO_CLOSED;
5672 cmd.srv_limit = IWN5000_TXPOWER_AUTO;
5673 DPRINTF(sc, IWN_DEBUG_CALIBRATE | IWN_DEBUG_XMIT,
5674 "%s: setting TX power; rev=%d\n",
5676 IWN_UCODE_API(sc->ucode_rev));
5677 if (IWN_UCODE_API(sc->ucode_rev) == 1)
5678 cmdid = IWN_CMD_TXPOWER_DBM_V1;
5680 cmdid = IWN_CMD_TXPOWER_DBM;
5681 return iwn_cmd(sc, cmdid, &cmd, sizeof cmd, async);
5685 * Retrieve the maximum RSSI (in dBm) among receivers.
5688 iwn4965_get_rssi(struct iwn_softc *sc, struct iwn_rx_stat *stat)
5690 struct iwn4965_rx_phystat *phy = (void *)stat->phybuf;
5694 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5696 mask = (le16toh(phy->antenna) >> 4) & IWN_ANT_ABC;
5697 agc = (le16toh(phy->agc) >> 7) & 0x7f;
5700 if (mask & IWN_ANT_A)
5701 rssi = MAX(rssi, phy->rssi[0]);
5702 if (mask & IWN_ANT_B)
5703 rssi = MAX(rssi, phy->rssi[2]);
5704 if (mask & IWN_ANT_C)
5705 rssi = MAX(rssi, phy->rssi[4]);
5707 DPRINTF(sc, IWN_DEBUG_RECV,
5708 "%s: agc %d mask 0x%x rssi %d %d %d result %d\n", __func__, agc,
5709 mask, phy->rssi[0], phy->rssi[2], phy->rssi[4],
5710 rssi - agc - IWN_RSSI_TO_DBM);
5711 return rssi - agc - IWN_RSSI_TO_DBM;
5715 iwn5000_get_rssi(struct iwn_softc *sc, struct iwn_rx_stat *stat)
5717 struct iwn5000_rx_phystat *phy = (void *)stat->phybuf;
5721 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5723 agc = (le32toh(phy->agc) >> 9) & 0x7f;
5725 rssi = MAX(le16toh(phy->rssi[0]) & 0xff,
5726 le16toh(phy->rssi[1]) & 0xff);
5727 rssi = MAX(le16toh(phy->rssi[2]) & 0xff, rssi);
5729 DPRINTF(sc, IWN_DEBUG_RECV,
5730 "%s: agc %d rssi %d %d %d result %d\n", __func__, agc,
5731 phy->rssi[0], phy->rssi[1], phy->rssi[2],
5732 rssi - agc - IWN_RSSI_TO_DBM);
5733 return rssi - agc - IWN_RSSI_TO_DBM;
5737 * Retrieve the average noise (in dBm) among receivers.
5740 iwn_get_noise(const struct iwn_rx_general_stats *stats)
5742 int i, total, nbant, noise;
5745 for (i = 0; i < 3; i++) {
5746 if ((noise = le32toh(stats->noise[i]) & 0xff) == 0)
5751 /* There should be at least one antenna but check anyway. */
5752 return (nbant == 0) ? -127 : (total / nbant) - 107;
5756 * Compute temperature (in degC) from last received statistics.
5759 iwn4965_get_temperature(struct iwn_softc *sc)
5761 struct iwn_ucode_info *uc = &sc->ucode_info;
5762 int32_t r1, r2, r3, r4, temp;
5764 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5766 r1 = le32toh(uc->temp[0].chan20MHz);
5767 r2 = le32toh(uc->temp[1].chan20MHz);
5768 r3 = le32toh(uc->temp[2].chan20MHz);
5769 r4 = le32toh(sc->rawtemp);
5771 if (r1 == r3) /* Prevents division by 0 (should not happen). */
5774 /* Sign-extend 23-bit R4 value to 32-bit. */
5775 r4 = ((r4 & 0xffffff) ^ 0x800000) - 0x800000;
5776 /* Compute temperature in Kelvin. */
5777 temp = (259 * (r4 - r2)) / (r3 - r1);
5778 temp = (temp * 97) / 100 + 8;
5780 DPRINTF(sc, IWN_DEBUG_ANY, "temperature %dK/%dC\n", temp,
5782 return IWN_KTOC(temp);
5786 iwn5000_get_temperature(struct iwn_softc *sc)
5790 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5793 * Temperature is not used by the driver for 5000 Series because
5794 * TX power calibration is handled by firmware.
5796 temp = le32toh(sc->rawtemp);
5797 if (sc->hw_type == IWN_HW_REV_TYPE_5150) {
5798 temp = (temp / -5) + sc->temp_off;
5799 temp = IWN_KTOC(temp);
5805 * Initialize sensitivity calibration state machine.
5808 iwn_init_sensitivity(struct iwn_softc *sc)
5810 struct iwn_ops *ops = &sc->ops;
5811 struct iwn_calib_state *calib = &sc->calib;
5815 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5817 /* Reset calibration state machine. */
5818 memset(calib, 0, sizeof (*calib));
5819 calib->state = IWN_CALIB_STATE_INIT;
5820 calib->cck_state = IWN_CCK_STATE_HIFA;
5821 /* Set initial correlation values. */
5822 calib->ofdm_x1 = sc->limits->min_ofdm_x1;
5823 calib->ofdm_mrc_x1 = sc->limits->min_ofdm_mrc_x1;
5824 calib->ofdm_x4 = sc->limits->min_ofdm_x4;
5825 calib->ofdm_mrc_x4 = sc->limits->min_ofdm_mrc_x4;
5826 calib->cck_x4 = 125;
5827 calib->cck_mrc_x4 = sc->limits->min_cck_mrc_x4;
5828 calib->energy_cck = sc->limits->energy_cck;
5830 /* Write initial sensitivity. */
5831 if ((error = iwn_send_sensitivity(sc)) != 0)
5834 /* Write initial gains. */
5835 if ((error = ops->init_gains(sc)) != 0)
5838 /* Request statistics at each beacon interval. */
5840 DPRINTF(sc, IWN_DEBUG_CALIBRATE, "%s: sending request for statistics\n",
5842 return iwn_cmd(sc, IWN_CMD_GET_STATISTICS, &flags, sizeof flags, 1);
5846 * Collect noise and RSSI statistics for the first 20 beacons received
5847 * after association and use them to determine connected antennas and
5848 * to set differential gains.
5851 iwn_collect_noise(struct iwn_softc *sc,
5852 const struct iwn_rx_general_stats *stats)
5854 struct iwn_ops *ops = &sc->ops;
5855 struct iwn_calib_state *calib = &sc->calib;
5856 struct ieee80211com *ic = &sc->sc_ic;
5860 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
5862 /* Accumulate RSSI and noise for all 3 antennas. */
5863 for (i = 0; i < 3; i++) {
5864 calib->rssi[i] += le32toh(stats->rssi[i]) & 0xff;
5865 calib->noise[i] += le32toh(stats->noise[i]) & 0xff;
5867 /* NB: We update differential gains only once after 20 beacons. */
5868 if (++calib->nbeacons < 20)
5871 /* Determine highest average RSSI. */
5872 val = MAX(calib->rssi[0], calib->rssi[1]);
5873 val = MAX(calib->rssi[2], val);
5875 /* Determine which antennas are connected. */
5876 sc->chainmask = sc->rxchainmask;
5877 for (i = 0; i < 3; i++)
5878 if (val - calib->rssi[i] > 15 * 20)
5879 sc->chainmask &= ~(1 << i);
5880 DPRINTF(sc, IWN_DEBUG_CALIBRATE | IWN_DEBUG_XMIT,
5881 "%s: RX chains mask: theoretical=0x%x, actual=0x%x\n",
5882 __func__, sc->rxchainmask, sc->chainmask);
5884 /* If none of the TX antennas are connected, keep at least one. */
5885 if ((sc->chainmask & sc->txchainmask) == 0)
5886 sc->chainmask |= IWN_LSB(sc->txchainmask);
5888 (void)ops->set_gains(sc);
5889 calib->state = IWN_CALIB_STATE_RUN;
5892 /* XXX Disable RX chains with no antennas connected. */
5893 sc->rxon->rxchain = htole16(IWN_RXCHAIN_SEL(sc->chainmask));
5894 if (sc->sc_is_scanning)
5895 device_printf(sc->sc_dev,
5896 "%s: is_scanning set, before RXON\n",
5898 (void)iwn_cmd(sc, IWN_CMD_RXON, sc->rxon, sc->rxonsz, 1);
5901 /* Enable power-saving mode if requested by user. */
5902 if (ic->ic_flags & IEEE80211_F_PMGTON)
5903 (void)iwn_set_pslevel(sc, 0, 3, 1);
5905 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
5910 iwn4965_init_gains(struct iwn_softc *sc)
5912 struct iwn_phy_calib_gain cmd;
5914 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5916 memset(&cmd, 0, sizeof cmd);
5917 cmd.code = IWN4965_PHY_CALIB_DIFF_GAIN;
5918 /* Differential gains initially set to 0 for all 3 antennas. */
5919 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
5920 "%s: setting initial differential gains\n", __func__);
5921 return iwn_cmd(sc, IWN_CMD_PHY_CALIB, &cmd, sizeof cmd, 1);
5925 iwn5000_init_gains(struct iwn_softc *sc)
5927 struct iwn_phy_calib cmd;
5929 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5931 memset(&cmd, 0, sizeof cmd);
5932 cmd.code = sc->reset_noise_gain;
5935 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
5936 "%s: setting initial differential gains\n", __func__);
5937 return iwn_cmd(sc, IWN_CMD_PHY_CALIB, &cmd, sizeof cmd, 1);
5941 iwn4965_set_gains(struct iwn_softc *sc)
5943 struct iwn_calib_state *calib = &sc->calib;
5944 struct iwn_phy_calib_gain cmd;
5945 int i, delta, noise;
5947 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5949 /* Get minimal noise among connected antennas. */
5950 noise = INT_MAX; /* NB: There's at least one antenna. */
5951 for (i = 0; i < 3; i++)
5952 if (sc->chainmask & (1 << i))
5953 noise = MIN(calib->noise[i], noise);
5955 memset(&cmd, 0, sizeof cmd);
5956 cmd.code = IWN4965_PHY_CALIB_DIFF_GAIN;
5957 /* Set differential gains for connected antennas. */
5958 for (i = 0; i < 3; i++) {
5959 if (sc->chainmask & (1 << i)) {
5960 /* Compute attenuation (in unit of 1.5dB). */
5961 delta = (noise - (int32_t)calib->noise[i]) / 30;
5962 /* NB: delta <= 0 */
5963 /* Limit to [-4.5dB,0]. */
5964 cmd.gain[i] = MIN(abs(delta), 3);
5966 cmd.gain[i] |= 1 << 2; /* sign bit */
5969 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
5970 "setting differential gains Ant A/B/C: %x/%x/%x (%x)\n",
5971 cmd.gain[0], cmd.gain[1], cmd.gain[2], sc->chainmask);
5972 return iwn_cmd(sc, IWN_CMD_PHY_CALIB, &cmd, sizeof cmd, 1);
5976 iwn5000_set_gains(struct iwn_softc *sc)
5978 struct iwn_calib_state *calib = &sc->calib;
5979 struct iwn_phy_calib_gain cmd;
5980 int i, ant, div, delta;
5982 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
5984 /* We collected 20 beacons and !=6050 need a 1.5 factor. */
5985 div = (sc->hw_type == IWN_HW_REV_TYPE_6050) ? 20 : 30;
5987 memset(&cmd, 0, sizeof cmd);
5988 cmd.code = sc->noise_gain;
5991 /* Get first available RX antenna as referential. */
5992 ant = IWN_LSB(sc->rxchainmask);
5993 /* Set differential gains for other antennas. */
5994 for (i = ant + 1; i < 3; i++) {
5995 if (sc->chainmask & (1 << i)) {
5996 /* The delta is relative to antenna "ant". */
5997 delta = ((int32_t)calib->noise[ant] -
5998 (int32_t)calib->noise[i]) / div;
5999 /* Limit to [-4.5dB,+4.5dB]. */
6000 cmd.gain[i - 1] = MIN(abs(delta), 3);
6002 cmd.gain[i - 1] |= 1 << 2; /* sign bit */
6005 DPRINTF(sc, IWN_DEBUG_CALIBRATE | IWN_DEBUG_XMIT,
6006 "setting differential gains Ant B/C: %x/%x (%x)\n",
6007 cmd.gain[0], cmd.gain[1], sc->chainmask);
6008 return iwn_cmd(sc, IWN_CMD_PHY_CALIB, &cmd, sizeof cmd, 1);
6012 * Tune RF RX sensitivity based on the number of false alarms detected
6013 * during the last beacon period.
6016 iwn_tune_sensitivity(struct iwn_softc *sc, const struct iwn_rx_stats *stats)
6018 #define inc(val, inc, max) \
6019 if ((val) < (max)) { \
6020 if ((val) < (max) - (inc)) \
6026 #define dec(val, dec, min) \
6027 if ((val) > (min)) { \
6028 if ((val) > (min) + (dec)) \
6035 const struct iwn_sensitivity_limits *limits = sc->limits;
6036 struct iwn_calib_state *calib = &sc->calib;
6037 uint32_t val, rxena, fa;
6038 uint32_t energy[3], energy_min;
6039 uint8_t noise[3], noise_ref;
6040 int i, needs_update = 0;
6042 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
6044 /* Check that we've been enabled long enough. */
6045 if ((rxena = le32toh(stats->general.load)) == 0){
6046 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end not so long\n", __func__);
6050 /* Compute number of false alarms since last call for OFDM. */
6051 fa = le32toh(stats->ofdm.bad_plcp) - calib->bad_plcp_ofdm;
6052 fa += le32toh(stats->ofdm.fa) - calib->fa_ofdm;
6053 fa *= 200 * IEEE80211_DUR_TU; /* 200TU */
6055 if (fa > 50 * rxena) {
6056 /* High false alarm count, decrease sensitivity. */
6057 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
6058 "%s: OFDM high false alarm count: %u\n", __func__, fa);
6059 inc(calib->ofdm_x1, 1, limits->max_ofdm_x1);
6060 inc(calib->ofdm_mrc_x1, 1, limits->max_ofdm_mrc_x1);
6061 inc(calib->ofdm_x4, 1, limits->max_ofdm_x4);
6062 inc(calib->ofdm_mrc_x4, 1, limits->max_ofdm_mrc_x4);
6064 } else if (fa < 5 * rxena) {
6065 /* Low false alarm count, increase sensitivity. */
6066 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
6067 "%s: OFDM low false alarm count: %u\n", __func__, fa);
6068 dec(calib->ofdm_x1, 1, limits->min_ofdm_x1);
6069 dec(calib->ofdm_mrc_x1, 1, limits->min_ofdm_mrc_x1);
6070 dec(calib->ofdm_x4, 1, limits->min_ofdm_x4);
6071 dec(calib->ofdm_mrc_x4, 1, limits->min_ofdm_mrc_x4);
6074 /* Compute maximum noise among 3 receivers. */
6075 for (i = 0; i < 3; i++)
6076 noise[i] = (le32toh(stats->general.noise[i]) >> 8) & 0xff;
6077 val = MAX(noise[0], noise[1]);
6078 val = MAX(noise[2], val);
6079 /* Insert it into our samples table. */
6080 calib->noise_samples[calib->cur_noise_sample] = val;
6081 calib->cur_noise_sample = (calib->cur_noise_sample + 1) % 20;
6083 /* Compute maximum noise among last 20 samples. */
6084 noise_ref = calib->noise_samples[0];
6085 for (i = 1; i < 20; i++)
6086 noise_ref = MAX(noise_ref, calib->noise_samples[i]);
6088 /* Compute maximum energy among 3 receivers. */
6089 for (i = 0; i < 3; i++)
6090 energy[i] = le32toh(stats->general.energy[i]);
6091 val = MIN(energy[0], energy[1]);
6092 val = MIN(energy[2], val);
6093 /* Insert it into our samples table. */
6094 calib->energy_samples[calib->cur_energy_sample] = val;
6095 calib->cur_energy_sample = (calib->cur_energy_sample + 1) % 10;
6097 /* Compute minimum energy among last 10 samples. */
6098 energy_min = calib->energy_samples[0];
6099 for (i = 1; i < 10; i++)
6100 energy_min = MAX(energy_min, calib->energy_samples[i]);
6103 /* Compute number of false alarms since last call for CCK. */
6104 fa = le32toh(stats->cck.bad_plcp) - calib->bad_plcp_cck;
6105 fa += le32toh(stats->cck.fa) - calib->fa_cck;
6106 fa *= 200 * IEEE80211_DUR_TU; /* 200TU */
6108 if (fa > 50 * rxena) {
6109 /* High false alarm count, decrease sensitivity. */
6110 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
6111 "%s: CCK high false alarm count: %u\n", __func__, fa);
6112 calib->cck_state = IWN_CCK_STATE_HIFA;
6115 if (calib->cck_x4 > 160) {
6116 calib->noise_ref = noise_ref;
6117 if (calib->energy_cck > 2)
6118 dec(calib->energy_cck, 2, energy_min);
6120 if (calib->cck_x4 < 160) {
6121 calib->cck_x4 = 161;
6124 inc(calib->cck_x4, 3, limits->max_cck_x4);
6126 inc(calib->cck_mrc_x4, 3, limits->max_cck_mrc_x4);
6128 } else if (fa < 5 * rxena) {
6129 /* Low false alarm count, increase sensitivity. */
6130 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
6131 "%s: CCK low false alarm count: %u\n", __func__, fa);
6132 calib->cck_state = IWN_CCK_STATE_LOFA;
6135 if (calib->cck_state != IWN_CCK_STATE_INIT &&
6136 (((int32_t)calib->noise_ref - (int32_t)noise_ref) > 2 ||
6137 calib->low_fa > 100)) {
6138 inc(calib->energy_cck, 2, limits->min_energy_cck);
6139 dec(calib->cck_x4, 3, limits->min_cck_x4);
6140 dec(calib->cck_mrc_x4, 3, limits->min_cck_mrc_x4);
6143 /* Not worth to increase or decrease sensitivity. */
6144 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
6145 "%s: CCK normal false alarm count: %u\n", __func__, fa);
6147 calib->noise_ref = noise_ref;
6149 if (calib->cck_state == IWN_CCK_STATE_HIFA) {
6150 /* Previous interval had many false alarms. */
6151 dec(calib->energy_cck, 8, energy_min);
6153 calib->cck_state = IWN_CCK_STATE_INIT;
6157 (void)iwn_send_sensitivity(sc);
6159 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
6166 iwn_send_sensitivity(struct iwn_softc *sc)
6168 struct iwn_calib_state *calib = &sc->calib;
6169 struct iwn_enhanced_sensitivity_cmd cmd;
6172 memset(&cmd, 0, sizeof cmd);
6173 len = sizeof (struct iwn_sensitivity_cmd);
6174 cmd.which = IWN_SENSITIVITY_WORKTBL;
6175 /* OFDM modulation. */
6176 cmd.corr_ofdm_x1 = htole16(calib->ofdm_x1);
6177 cmd.corr_ofdm_mrc_x1 = htole16(calib->ofdm_mrc_x1);
6178 cmd.corr_ofdm_x4 = htole16(calib->ofdm_x4);
6179 cmd.corr_ofdm_mrc_x4 = htole16(calib->ofdm_mrc_x4);
6180 cmd.energy_ofdm = htole16(sc->limits->energy_ofdm);
6181 cmd.energy_ofdm_th = htole16(62);
6182 /* CCK modulation. */
6183 cmd.corr_cck_x4 = htole16(calib->cck_x4);
6184 cmd.corr_cck_mrc_x4 = htole16(calib->cck_mrc_x4);
6185 cmd.energy_cck = htole16(calib->energy_cck);
6186 /* Barker modulation: use default values. */
6187 cmd.corr_barker = htole16(190);
6188 cmd.corr_barker_mrc = htole16(sc->limits->barker_mrc);
6190 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
6191 "%s: set sensitivity %d/%d/%d/%d/%d/%d/%d\n", __func__,
6192 calib->ofdm_x1, calib->ofdm_mrc_x1, calib->ofdm_x4,
6193 calib->ofdm_mrc_x4, calib->cck_x4,
6194 calib->cck_mrc_x4, calib->energy_cck);
6196 if (!(sc->sc_flags & IWN_FLAG_ENH_SENS))
6198 /* Enhanced sensitivity settings. */
6199 len = sizeof (struct iwn_enhanced_sensitivity_cmd);
6200 cmd.ofdm_det_slope_mrc = htole16(668);
6201 cmd.ofdm_det_icept_mrc = htole16(4);
6202 cmd.ofdm_det_slope = htole16(486);
6203 cmd.ofdm_det_icept = htole16(37);
6204 cmd.cck_det_slope_mrc = htole16(853);
6205 cmd.cck_det_icept_mrc = htole16(4);
6206 cmd.cck_det_slope = htole16(476);
6207 cmd.cck_det_icept = htole16(99);
6209 return iwn_cmd(sc, IWN_CMD_SET_SENSITIVITY, &cmd, len, 1);
6213 * Look at the increase of PLCP errors over time; if it exceeds
6214 * a programmed threshold then trigger an RF retune.
6217 iwn_check_rx_recovery(struct iwn_softc *sc, struct iwn_stats *rs)
6219 int32_t delta_ofdm, delta_ht, delta_cck;
6220 struct iwn_calib_state *calib = &sc->calib;
6221 int delta_ticks, cur_ticks;
6226 * Calculate the difference between the current and
6227 * previous statistics.
6229 delta_cck = le32toh(rs->rx.cck.bad_plcp) - calib->bad_plcp_cck;
6230 delta_ofdm = le32toh(rs->rx.ofdm.bad_plcp) - calib->bad_plcp_ofdm;
6231 delta_ht = le32toh(rs->rx.ht.bad_plcp) - calib->bad_plcp_ht;
6234 * Calculate the delta in time between successive statistics
6235 * messages. Yes, it can roll over; so we make sure that
6236 * this doesn't happen.
6238 * XXX go figure out what to do about rollover
6239 * XXX go figure out what to do if ticks rolls over to -ve instead!
6240 * XXX go stab signed integer overflow undefined-ness in the face.
6243 delta_ticks = cur_ticks - sc->last_calib_ticks;
6246 * If any are negative, then the firmware likely reset; so just
6247 * bail. We'll pick this up next time.
6249 if (delta_cck < 0 || delta_ofdm < 0 || delta_ht < 0 || delta_ticks < 0)
6253 * delta_ticks is in ticks; we need to convert it up to milliseconds
6254 * so we can do some useful math with it.
6256 delta_msec = ticks_to_msecs(delta_ticks);
6259 * Calculate what our threshold is given the current delta_msec.
6261 thresh = sc->base_params->plcp_err_threshold * delta_msec;
6263 DPRINTF(sc, IWN_DEBUG_STATE,
6264 "%s: time delta: %d; cck=%d, ofdm=%d, ht=%d, total=%d, thresh=%d\n",
6270 (delta_msec + delta_cck + delta_ofdm + delta_ht),
6274 * If we need a retune, then schedule a single channel scan
6275 * to a channel that isn't the currently active one!
6277 * The math from linux iwlwifi:
6279 * if ((delta * 100 / msecs) > threshold)
6281 if (thresh > 0 && (delta_cck + delta_ofdm + delta_ht) * 100 > thresh) {
6282 DPRINTF(sc, IWN_DEBUG_ANY,
6283 "%s: PLCP error threshold raw (%d) comparison (%d) "
6284 "over limit (%d); retune!\n",
6286 (delta_cck + delta_ofdm + delta_ht),
6287 (delta_cck + delta_ofdm + delta_ht) * 100,
6293 * Set STA mode power saving level (between 0 and 5).
6294 * Level 0 is CAM (Continuously Aware Mode), 5 is for maximum power saving.
6297 iwn_set_pslevel(struct iwn_softc *sc, int dtim, int level, int async)
6299 struct iwn_pmgt_cmd cmd;
6300 const struct iwn_pmgt *pmgt;
6301 uint32_t max, skip_dtim;
6305 DPRINTF(sc, IWN_DEBUG_PWRSAVE,
6306 "%s: dtim=%d, level=%d, async=%d\n",
6312 /* Select which PS parameters to use. */
6314 pmgt = &iwn_pmgt[0][level];
6315 else if (dtim <= 10)
6316 pmgt = &iwn_pmgt[1][level];
6318 pmgt = &iwn_pmgt[2][level];
6320 memset(&cmd, 0, sizeof cmd);
6321 if (level != 0) /* not CAM */
6322 cmd.flags |= htole16(IWN_PS_ALLOW_SLEEP);
6324 cmd.flags |= htole16(IWN_PS_FAST_PD);
6325 /* Retrieve PCIe Active State Power Management (ASPM). */
6326 reg = pci_read_config(sc->sc_dev, sc->sc_cap_off + PCIER_LINK_CTL, 4);
6327 if (!(reg & PCIEM_LINK_CTL_ASPMC_L0S)) /* L0s Entry disabled. */
6328 cmd.flags |= htole16(IWN_PS_PCI_PMGT);
6329 cmd.rxtimeout = htole32(pmgt->rxtimeout * 1024);
6330 cmd.txtimeout = htole32(pmgt->txtimeout * 1024);
6336 skip_dtim = pmgt->skip_dtim;
6337 if (skip_dtim != 0) {
6338 cmd.flags |= htole16(IWN_PS_SLEEP_OVER_DTIM);
6339 max = pmgt->intval[4];
6340 if (max == (uint32_t)-1)
6341 max = dtim * (skip_dtim + 1);
6342 else if (max > dtim)
6343 max = rounddown(max, dtim);
6346 for (i = 0; i < 5; i++)
6347 cmd.intval[i] = htole32(MIN(max, pmgt->intval[i]));
6349 DPRINTF(sc, IWN_DEBUG_RESET, "setting power saving level to %d\n",
6351 return iwn_cmd(sc, IWN_CMD_SET_POWER_MODE, &cmd, sizeof cmd, async);
6355 iwn_send_btcoex(struct iwn_softc *sc)
6357 struct iwn_bluetooth cmd;
6359 memset(&cmd, 0, sizeof cmd);
6360 cmd.flags = IWN_BT_COEX_CHAN_ANN | IWN_BT_COEX_BT_PRIO;
6361 cmd.lead_time = IWN_BT_LEAD_TIME_DEF;
6362 cmd.max_kill = IWN_BT_MAX_KILL_DEF;
6363 DPRINTF(sc, IWN_DEBUG_RESET, "%s: configuring bluetooth coexistence\n",
6365 return iwn_cmd(sc, IWN_CMD_BT_COEX, &cmd, sizeof(cmd), 0);
6369 iwn_send_advanced_btcoex(struct iwn_softc *sc)
6371 static const uint32_t btcoex_3wire[12] = {
6372 0xaaaaaaaa, 0xaaaaaaaa, 0xaeaaaaaa, 0xaaaaaaaa,
6373 0xcc00ff28, 0x0000aaaa, 0xcc00aaaa, 0x0000aaaa,
6374 0xc0004000, 0x00004000, 0xf0005000, 0xf0005000,
6376 struct iwn6000_btcoex_config btconfig;
6377 struct iwn2000_btcoex_config btconfig2k;
6378 struct iwn_btcoex_priotable btprio;
6379 struct iwn_btcoex_prot btprot;
6383 memset(&btconfig, 0, sizeof btconfig);
6384 memset(&btconfig2k, 0, sizeof btconfig2k);
6386 flags = IWN_BT_FLAG_COEX6000_MODE_3W <<
6387 IWN_BT_FLAG_COEX6000_MODE_SHIFT; // Done as is in linux kernel 3.2
6389 if (sc->base_params->bt_sco_disable)
6390 flags &= ~IWN_BT_FLAG_SYNC_2_BT_DISABLE;
6392 flags |= IWN_BT_FLAG_SYNC_2_BT_DISABLE;
6394 flags |= IWN_BT_FLAG_COEX6000_CHAN_INHIBITION;
6396 /* Default flags result is 145 as old value */
6399 * Flags value has to be review. Values must change if we
6400 * which to disable it
6402 if (sc->base_params->bt_session_2) {
6403 btconfig2k.flags = flags;
6404 btconfig2k.max_kill = 5;
6405 btconfig2k.bt3_t7_timer = 1;
6406 btconfig2k.kill_ack = htole32(0xffff0000);
6407 btconfig2k.kill_cts = htole32(0xffff0000);
6408 btconfig2k.sample_time = 2;
6409 btconfig2k.bt3_t2_timer = 0xc;
6411 for (i = 0; i < 12; i++)
6412 btconfig2k.lookup_table[i] = htole32(btcoex_3wire[i]);
6413 btconfig2k.valid = htole16(0xff);
6414 btconfig2k.prio_boost = htole32(0xf0);
6415 DPRINTF(sc, IWN_DEBUG_RESET,
6416 "%s: configuring advanced bluetooth coexistence"
6417 " session 2, flags : 0x%x\n",
6420 error = iwn_cmd(sc, IWN_CMD_BT_COEX, &btconfig2k,
6421 sizeof(btconfig2k), 1);
6423 btconfig.flags = flags;
6424 btconfig.max_kill = 5;
6425 btconfig.bt3_t7_timer = 1;
6426 btconfig.kill_ack = htole32(0xffff0000);
6427 btconfig.kill_cts = htole32(0xffff0000);
6428 btconfig.sample_time = 2;
6429 btconfig.bt3_t2_timer = 0xc;
6431 for (i = 0; i < 12; i++)
6432 btconfig.lookup_table[i] = htole32(btcoex_3wire[i]);
6433 btconfig.valid = htole16(0xff);
6434 btconfig.prio_boost = 0xf0;
6435 DPRINTF(sc, IWN_DEBUG_RESET,
6436 "%s: configuring advanced bluetooth coexistence,"
6440 error = iwn_cmd(sc, IWN_CMD_BT_COEX, &btconfig,
6441 sizeof(btconfig), 1);
6447 memset(&btprio, 0, sizeof btprio);
6448 btprio.calib_init1 = 0x6;
6449 btprio.calib_init2 = 0x7;
6450 btprio.calib_periodic_low1 = 0x2;
6451 btprio.calib_periodic_low2 = 0x3;
6452 btprio.calib_periodic_high1 = 0x4;
6453 btprio.calib_periodic_high2 = 0x5;
6455 btprio.scan52 = 0x8;
6456 btprio.scan24 = 0xa;
6457 error = iwn_cmd(sc, IWN_CMD_BT_COEX_PRIOTABLE, &btprio, sizeof(btprio),
6462 /* Force BT state machine change. */
6463 memset(&btprot, 0, sizeof btprot);
6466 error = iwn_cmd(sc, IWN_CMD_BT_COEX_PROT, &btprot, sizeof(btprot), 1);
6470 return iwn_cmd(sc, IWN_CMD_BT_COEX_PROT, &btprot, sizeof(btprot), 1);
6474 iwn5000_runtime_calib(struct iwn_softc *sc)
6476 struct iwn5000_calib_config cmd;
6478 memset(&cmd, 0, sizeof cmd);
6479 cmd.ucode.once.enable = 0xffffffff;
6480 cmd.ucode.once.start = IWN5000_CALIB_DC;
6481 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
6482 "%s: configuring runtime calibration\n", __func__);
6483 return iwn_cmd(sc, IWN5000_CMD_CALIB_CONFIG, &cmd, sizeof(cmd), 0);
6487 iwn_get_rxon_ht_flags(struct iwn_softc *sc, struct ieee80211_channel *c)
6489 struct ieee80211com *ic = &sc->sc_ic;
6490 uint32_t htflags = 0;
6492 if (! IEEE80211_IS_CHAN_HT(c))
6495 htflags |= IWN_RXON_HT_PROTMODE(ic->ic_curhtprotmode);
6497 if (IEEE80211_IS_CHAN_HT40(c)) {
6498 switch (ic->ic_curhtprotmode) {
6499 case IEEE80211_HTINFO_OPMODE_HT20PR:
6500 htflags |= IWN_RXON_HT_MODEPURE40;
6503 htflags |= IWN_RXON_HT_MODEMIXED;
6507 if (IEEE80211_IS_CHAN_HT40D(c))
6508 htflags |= IWN_RXON_HT_HT40MINUS;
6514 iwn_config(struct iwn_softc *sc)
6516 struct iwn_ops *ops = &sc->ops;
6517 struct ieee80211com *ic = &sc->sc_ic;
6518 struct ieee80211vap *vap = TAILQ_FIRST(&ic->ic_vaps);
6519 const uint8_t *macaddr;
6524 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
6526 if ((sc->base_params->calib_need & IWN_FLG_NEED_PHY_CALIB_TEMP_OFFSET)
6527 && (sc->base_params->calib_need & IWN_FLG_NEED_PHY_CALIB_TEMP_OFFSETv2)) {
6528 device_printf(sc->sc_dev,"%s: temp_offset and temp_offsetv2 are"
6529 " exclusive each together. Review NIC config file. Conf"
6530 " : 0x%08x Flags : 0x%08x \n", __func__,
6531 sc->base_params->calib_need,
6532 (IWN_FLG_NEED_PHY_CALIB_TEMP_OFFSET |
6533 IWN_FLG_NEED_PHY_CALIB_TEMP_OFFSETv2));
6537 /* Compute temperature calib if needed. Will be send by send calib */
6538 if (sc->base_params->calib_need & IWN_FLG_NEED_PHY_CALIB_TEMP_OFFSET) {
6539 error = iwn5000_temp_offset_calib(sc);
6541 device_printf(sc->sc_dev,
6542 "%s: could not set temperature offset\n", __func__);
6545 } else if (sc->base_params->calib_need & IWN_FLG_NEED_PHY_CALIB_TEMP_OFFSETv2) {
6546 error = iwn5000_temp_offset_calibv2(sc);
6548 device_printf(sc->sc_dev,
6549 "%s: could not compute temperature offset v2\n",
6555 if (sc->hw_type == IWN_HW_REV_TYPE_6050) {
6556 /* Configure runtime DC calibration. */
6557 error = iwn5000_runtime_calib(sc);
6559 device_printf(sc->sc_dev,
6560 "%s: could not configure runtime calibration\n",
6566 /* Configure valid TX chains for >=5000 Series. */
6567 if (sc->hw_type != IWN_HW_REV_TYPE_4965 &&
6568 IWN_UCODE_API(sc->ucode_rev) > 1) {
6569 txmask = htole32(sc->txchainmask);
6570 DPRINTF(sc, IWN_DEBUG_RESET | IWN_DEBUG_XMIT,
6571 "%s: configuring valid TX chains 0x%x\n", __func__, txmask);
6572 error = iwn_cmd(sc, IWN5000_CMD_TX_ANT_CONFIG, &txmask,
6575 device_printf(sc->sc_dev,
6576 "%s: could not configure valid TX chains, "
6577 "error %d\n", __func__, error);
6582 /* Configure bluetooth coexistence. */
6585 /* Configure bluetooth coexistence if needed. */
6586 if (sc->base_params->bt_mode == IWN_BT_ADVANCED)
6587 error = iwn_send_advanced_btcoex(sc);
6588 if (sc->base_params->bt_mode == IWN_BT_SIMPLE)
6589 error = iwn_send_btcoex(sc);
6592 device_printf(sc->sc_dev,
6593 "%s: could not configure bluetooth coexistence, error %d\n",
6598 /* Set mode, channel, RX filter and enable RX. */
6599 sc->rxon = &sc->rx_on[IWN_RXON_BSS_CTX];
6600 memset(sc->rxon, 0, sizeof (struct iwn_rxon));
6601 macaddr = vap ? vap->iv_myaddr : ic->ic_macaddr;
6602 IEEE80211_ADDR_COPY(sc->rxon->myaddr, macaddr);
6603 IEEE80211_ADDR_COPY(sc->rxon->wlap, macaddr);
6604 sc->rxon->chan = ieee80211_chan2ieee(ic, ic->ic_curchan);
6605 sc->rxon->flags = htole32(IWN_RXON_TSF | IWN_RXON_CTS_TO_SELF);
6606 if (IEEE80211_IS_CHAN_2GHZ(ic->ic_curchan))
6607 sc->rxon->flags |= htole32(IWN_RXON_AUTO | IWN_RXON_24GHZ);
6608 switch (ic->ic_opmode) {
6609 case IEEE80211_M_STA:
6610 sc->rxon->mode = IWN_MODE_STA;
6611 sc->rxon->filter = htole32(IWN_FILTER_MULTICAST);
6613 case IEEE80211_M_MONITOR:
6614 sc->rxon->mode = IWN_MODE_MONITOR;
6615 sc->rxon->filter = htole32(IWN_FILTER_MULTICAST |
6616 IWN_FILTER_CTL | IWN_FILTER_PROMISC);
6619 /* Should not get there. */
6622 sc->rxon->cck_mask = 0x0f; /* not yet negotiated */
6623 sc->rxon->ofdm_mask = 0xff; /* not yet negotiated */
6624 sc->rxon->ht_single_mask = 0xff;
6625 sc->rxon->ht_dual_mask = 0xff;
6626 sc->rxon->ht_triple_mask = 0xff;
6628 * In active association mode, ensure that
6629 * all the receive chains are enabled.
6631 * Since we're not yet doing SMPS, don't allow the
6632 * number of idle RX chains to be less than the active
6636 IWN_RXCHAIN_VALID(sc->rxchainmask) |
6637 IWN_RXCHAIN_MIMO_COUNT(sc->nrxchains) |
6638 IWN_RXCHAIN_IDLE_COUNT(sc->nrxchains);
6639 sc->rxon->rxchain = htole16(rxchain);
6640 DPRINTF(sc, IWN_DEBUG_RESET | IWN_DEBUG_XMIT,
6641 "%s: rxchainmask=0x%x, nrxchains=%d\n",
6646 sc->rxon->flags |= htole32(iwn_get_rxon_ht_flags(sc, ic->ic_curchan));
6648 DPRINTF(sc, IWN_DEBUG_RESET,
6649 "%s: setting configuration; flags=0x%08x\n",
6650 __func__, le32toh(sc->rxon->flags));
6651 if (sc->sc_is_scanning)
6652 device_printf(sc->sc_dev,
6653 "%s: is_scanning set, before RXON\n",
6655 error = iwn_cmd(sc, IWN_CMD_RXON, sc->rxon, sc->rxonsz, 0);
6657 device_printf(sc->sc_dev, "%s: RXON command failed\n",
6662 if ((error = iwn_add_broadcast_node(sc, 0)) != 0) {
6663 device_printf(sc->sc_dev, "%s: could not add broadcast node\n",
6668 /* Configuration has changed, set TX power accordingly. */
6669 if ((error = ops->set_txpower(sc, ic->ic_curchan, 0)) != 0) {
6670 device_printf(sc->sc_dev, "%s: could not set TX power\n",
6675 if ((error = iwn_set_critical_temp(sc)) != 0) {
6676 device_printf(sc->sc_dev,
6677 "%s: could not set critical temperature\n", __func__);
6681 /* Set power saving level to CAM during initialization. */
6682 if ((error = iwn_set_pslevel(sc, 0, 0, 0)) != 0) {
6683 device_printf(sc->sc_dev,
6684 "%s: could not set power saving level\n", __func__);
6688 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
6694 iwn_get_active_dwell_time(struct iwn_softc *sc,
6695 struct ieee80211_channel *c, uint8_t n_probes)
6697 /* No channel? Default to 2GHz settings */
6698 if (c == NULL || IEEE80211_IS_CHAN_2GHZ(c)) {
6699 return (IWN_ACTIVE_DWELL_TIME_2GHZ +
6700 IWN_ACTIVE_DWELL_FACTOR_2GHZ * (n_probes + 1));
6703 /* 5GHz dwell time */
6704 return (IWN_ACTIVE_DWELL_TIME_5GHZ +
6705 IWN_ACTIVE_DWELL_FACTOR_5GHZ * (n_probes + 1));
6709 * Limit the total dwell time to 85% of the beacon interval.
6711 * Returns the dwell time in milliseconds.
6714 iwn_limit_dwell(struct iwn_softc *sc, uint16_t dwell_time)
6716 struct ieee80211com *ic = &sc->sc_ic;
6717 struct ieee80211vap *vap = NULL;
6720 /* bintval is in TU (1.024mS) */
6721 if (! TAILQ_EMPTY(&ic->ic_vaps)) {
6722 vap = TAILQ_FIRST(&ic->ic_vaps);
6723 bintval = vap->iv_bss->ni_intval;
6727 * If it's non-zero, we should calculate the minimum of
6728 * it and the DWELL_BASE.
6730 * XXX Yes, the math should take into account that bintval
6731 * is 1.024mS, not 1mS..
6734 DPRINTF(sc, IWN_DEBUG_SCAN,
6738 return (MIN(IWN_PASSIVE_DWELL_BASE, ((bintval * 85) / 100)));
6741 /* No association context? Default */
6742 return (IWN_PASSIVE_DWELL_BASE);
6746 iwn_get_passive_dwell_time(struct iwn_softc *sc, struct ieee80211_channel *c)
6750 if (c == NULL || IEEE80211_IS_CHAN_2GHZ(c)) {
6751 passive = IWN_PASSIVE_DWELL_BASE + IWN_PASSIVE_DWELL_TIME_2GHZ;
6753 passive = IWN_PASSIVE_DWELL_BASE + IWN_PASSIVE_DWELL_TIME_5GHZ;
6756 /* Clamp to the beacon interval if we're associated */
6757 return (iwn_limit_dwell(sc, passive));
6761 iwn_scan(struct iwn_softc *sc, struct ieee80211vap *vap,
6762 struct ieee80211_scan_state *ss, struct ieee80211_channel *c)
6764 struct ieee80211com *ic = &sc->sc_ic;
6765 struct ieee80211_node *ni = vap->iv_bss;
6766 struct iwn_scan_hdr *hdr;
6767 struct iwn_cmd_data *tx;
6768 struct iwn_scan_essid *essid;
6769 struct iwn_scan_chan *chan;
6770 struct ieee80211_frame *wh;
6771 struct ieee80211_rateset *rs;
6777 uint16_t dwell_active, dwell_passive;
6778 uint32_t extra, scan_service_time;
6780 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
6783 * We are absolutely not allowed to send a scan command when another
6784 * scan command is pending.
6786 if (sc->sc_is_scanning) {
6787 device_printf(sc->sc_dev, "%s: called whilst scanning!\n",
6792 /* Assign the scan channel */
6795 sc->rxon = &sc->rx_on[IWN_RXON_BSS_CTX];
6796 buf = malloc(IWN_SCAN_MAXSZ, M_DEVBUF, M_NOWAIT | M_ZERO);
6798 device_printf(sc->sc_dev,
6799 "%s: could not allocate buffer for scan command\n",
6803 hdr = (struct iwn_scan_hdr *)buf;
6805 * Move to the next channel if no frames are received within 10ms
6806 * after sending the probe request.
6808 hdr->quiet_time = htole16(10); /* timeout in milliseconds */
6809 hdr->quiet_threshold = htole16(1); /* min # of packets */
6811 * Max needs to be greater than active and passive and quiet!
6812 * It's also in microseconds!
6814 hdr->max_svc = htole32(250 * 1024);
6817 * Reset scan: interval=100
6818 * Normal scan: interval=becaon interval
6819 * suspend_time: 100 (TU)
6822 extra = (100 /* suspend_time */ / 100 /* beacon interval */) << 22;
6823 //scan_service_time = extra | ((100 /* susp */ % 100 /* int */) * 1024);
6824 scan_service_time = (4 << 22) | (100 * 1024); /* Hardcode for now! */
6825 hdr->pause_svc = htole32(scan_service_time);
6827 /* Select antennas for scanning. */
6829 IWN_RXCHAIN_VALID(sc->rxchainmask) |
6830 IWN_RXCHAIN_FORCE_MIMO_SEL(sc->rxchainmask) |
6831 IWN_RXCHAIN_DRIVER_FORCE;
6832 if (IEEE80211_IS_CHAN_A(c) &&
6833 sc->hw_type == IWN_HW_REV_TYPE_4965) {
6834 /* Ant A must be avoided in 5GHz because of an HW bug. */
6835 rxchain |= IWN_RXCHAIN_FORCE_SEL(IWN_ANT_B);
6836 } else /* Use all available RX antennas. */
6837 rxchain |= IWN_RXCHAIN_FORCE_SEL(sc->rxchainmask);
6838 hdr->rxchain = htole16(rxchain);
6839 hdr->filter = htole32(IWN_FILTER_MULTICAST | IWN_FILTER_BEACON);
6841 tx = (struct iwn_cmd_data *)(hdr + 1);
6842 tx->flags = htole32(IWN_TX_AUTO_SEQ);
6843 tx->id = sc->broadcast_id;
6844 tx->lifetime = htole32(IWN_LIFETIME_INFINITE);
6846 if (IEEE80211_IS_CHAN_5GHZ(c)) {
6847 /* Send probe requests at 6Mbps. */
6848 tx->rate = htole32(0xd);
6849 rs = &ic->ic_sup_rates[IEEE80211_MODE_11A];
6851 hdr->flags = htole32(IWN_RXON_24GHZ | IWN_RXON_AUTO);
6852 if (sc->hw_type == IWN_HW_REV_TYPE_4965 &&
6853 sc->rxon->associd && sc->rxon->chan > 14)
6854 tx->rate = htole32(0xd);
6856 /* Send probe requests at 1Mbps. */
6857 tx->rate = htole32(10 | IWN_RFLAG_CCK);
6859 rs = &ic->ic_sup_rates[IEEE80211_MODE_11G];
6861 /* Use the first valid TX antenna. */
6862 txant = IWN_LSB(sc->txchainmask);
6863 tx->rate |= htole32(IWN_RFLAG_ANT(txant));
6866 * Only do active scanning if we're announcing a probe request
6867 * for a given SSID (or more, if we ever add it to the driver.)
6872 * If we're scanning for a specific SSID, add it to the command.
6874 * XXX maybe look at adding support for scanning multiple SSIDs?
6876 essid = (struct iwn_scan_essid *)(tx + 1);
6878 if (ss->ss_ssid[0].len != 0) {
6879 essid[0].id = IEEE80211_ELEMID_SSID;
6880 essid[0].len = ss->ss_ssid[0].len;
6881 memcpy(essid[0].data, ss->ss_ssid[0].ssid, ss->ss_ssid[0].len);
6884 DPRINTF(sc, IWN_DEBUG_SCAN, "%s: ssid_len=%d, ssid=%*s\n",
6888 ss->ss_ssid[0].ssid);
6890 if (ss->ss_nssid > 0)
6895 * Build a probe request frame. Most of the following code is a
6896 * copy & paste of what is done in net80211.
6898 wh = (struct ieee80211_frame *)(essid + 20);
6899 wh->i_fc[0] = IEEE80211_FC0_VERSION_0 | IEEE80211_FC0_TYPE_MGT |
6900 IEEE80211_FC0_SUBTYPE_PROBE_REQ;
6901 wh->i_fc[1] = IEEE80211_FC1_DIR_NODS;
6902 IEEE80211_ADDR_COPY(wh->i_addr1, vap->iv_ifp->if_broadcastaddr);
6903 IEEE80211_ADDR_COPY(wh->i_addr2, IF_LLADDR(vap->iv_ifp));
6904 IEEE80211_ADDR_COPY(wh->i_addr3, vap->iv_ifp->if_broadcastaddr);
6905 *(uint16_t *)&wh->i_dur[0] = 0; /* filled by HW */
6906 *(uint16_t *)&wh->i_seq[0] = 0; /* filled by HW */
6908 frm = (uint8_t *)(wh + 1);
6909 frm = ieee80211_add_ssid(frm, NULL, 0);
6910 frm = ieee80211_add_rates(frm, rs);
6911 if (rs->rs_nrates > IEEE80211_RATE_SIZE)
6912 frm = ieee80211_add_xrates(frm, rs);
6913 if (ic->ic_htcaps & IEEE80211_HTC_HT)
6914 frm = ieee80211_add_htcap(frm, ni);
6916 /* Set length of probe request. */
6917 tx->len = htole16(frm - (uint8_t *)wh);
6920 * If active scanning is requested but a certain channel is
6921 * marked passive, we can do active scanning if we detect
6924 * There is an issue with some firmware versions that triggers
6925 * a sysassert on a "good CRC threshold" of zero (== disabled),
6926 * on a radar channel even though this means that we should NOT
6929 * The "good CRC threshold" is the number of frames that we
6930 * need to receive during our dwell time on a channel before
6931 * sending out probes -- setting this to a huge value will
6932 * mean we never reach it, but at the same time work around
6933 * the aforementioned issue. Thus use IWL_GOOD_CRC_TH_NEVER
6934 * here instead of IWL_GOOD_CRC_TH_DISABLED.
6936 * This was fixed in later versions along with some other
6937 * scan changes, and the threshold behaves as a flag in those
6942 * If we're doing active scanning, set the crc_threshold
6943 * to a suitable value. This is different to active veruss
6944 * passive scanning depending upon the channel flags; the
6945 * firmware will obey that particular check for us.
6947 if (sc->tlv_feature_flags & IWN_UCODE_TLV_FLAGS_NEWSCAN)
6948 hdr->crc_threshold = is_active ?
6949 IWN_GOOD_CRC_TH_DEFAULT : IWN_GOOD_CRC_TH_DISABLED;
6951 hdr->crc_threshold = is_active ?
6952 IWN_GOOD_CRC_TH_DEFAULT : IWN_GOOD_CRC_TH_NEVER;
6954 chan = (struct iwn_scan_chan *)frm;
6955 chan->chan = htole16(ieee80211_chan2ieee(ic, c));
6957 if (ss->ss_nssid > 0)
6958 chan->flags |= htole32(IWN_CHAN_NPBREQS(1));
6959 chan->dsp_gain = 0x6e;
6962 * Set the passive/active flag depending upon the channel mode.
6963 * XXX TODO: take the is_active flag into account as well?
6965 if (c->ic_flags & IEEE80211_CHAN_PASSIVE)
6966 chan->flags |= htole32(IWN_CHAN_PASSIVE);
6968 chan->flags |= htole32(IWN_CHAN_ACTIVE);
6971 * Calculate the active/passive dwell times.
6974 dwell_active = iwn_get_active_dwell_time(sc, c, ss->ss_nssid);
6975 dwell_passive = iwn_get_passive_dwell_time(sc, c);
6977 /* Make sure they're valid */
6978 if (dwell_passive <= dwell_active)
6979 dwell_passive = dwell_active + 1;
6981 chan->active = htole16(dwell_active);
6982 chan->passive = htole16(dwell_passive);
6984 if (IEEE80211_IS_CHAN_5GHZ(c))
6985 chan->rf_gain = 0x3b;
6987 chan->rf_gain = 0x28;
6989 DPRINTF(sc, IWN_DEBUG_STATE,
6990 "%s: chan %u flags 0x%x rf_gain 0x%x "
6991 "dsp_gain 0x%x active %d passive %d scan_svc_time %d crc 0x%x "
6992 "isactive=%d numssid=%d\n", __func__,
6993 chan->chan, chan->flags, chan->rf_gain, chan->dsp_gain,
6994 dwell_active, dwell_passive, scan_service_time,
6995 hdr->crc_threshold, is_active, ss->ss_nssid);
6999 buflen = (uint8_t *)chan - buf;
7000 hdr->len = htole16(buflen);
7002 if (sc->sc_is_scanning) {
7003 device_printf(sc->sc_dev,
7004 "%s: called with is_scanning set!\n",
7007 sc->sc_is_scanning = 1;
7009 DPRINTF(sc, IWN_DEBUG_STATE, "sending scan command nchan=%d\n",
7011 error = iwn_cmd(sc, IWN_CMD_SCAN, buf, buflen, 1);
7012 free(buf, M_DEVBUF);
7014 callout_reset(&sc->scan_timeout, 5*hz, iwn_scan_timeout, sc);
7016 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
7022 iwn_auth(struct iwn_softc *sc, struct ieee80211vap *vap)
7024 struct iwn_ops *ops = &sc->ops;
7025 struct ieee80211com *ic = &sc->sc_ic;
7026 struct ieee80211_node *ni = vap->iv_bss;
7029 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
7031 sc->rxon = &sc->rx_on[IWN_RXON_BSS_CTX];
7032 /* Update adapter configuration. */
7033 IEEE80211_ADDR_COPY(sc->rxon->bssid, ni->ni_bssid);
7034 sc->rxon->chan = ieee80211_chan2ieee(ic, ni->ni_chan);
7035 sc->rxon->flags = htole32(IWN_RXON_TSF | IWN_RXON_CTS_TO_SELF);
7036 if (IEEE80211_IS_CHAN_2GHZ(ni->ni_chan))
7037 sc->rxon->flags |= htole32(IWN_RXON_AUTO | IWN_RXON_24GHZ);
7038 if (ic->ic_flags & IEEE80211_F_SHSLOT)
7039 sc->rxon->flags |= htole32(IWN_RXON_SHSLOT);
7040 if (ic->ic_flags & IEEE80211_F_SHPREAMBLE)
7041 sc->rxon->flags |= htole32(IWN_RXON_SHPREAMBLE);
7042 if (IEEE80211_IS_CHAN_A(ni->ni_chan)) {
7043 sc->rxon->cck_mask = 0;
7044 sc->rxon->ofdm_mask = 0x15;
7045 } else if (IEEE80211_IS_CHAN_B(ni->ni_chan)) {
7046 sc->rxon->cck_mask = 0x03;
7047 sc->rxon->ofdm_mask = 0;
7049 /* Assume 802.11b/g. */
7050 sc->rxon->cck_mask = 0x03;
7051 sc->rxon->ofdm_mask = 0x15;
7055 sc->rxon->flags |= htole32(iwn_get_rxon_ht_flags(sc, ic->ic_curchan));
7057 DPRINTF(sc, IWN_DEBUG_STATE, "rxon chan %d flags %x cck %x ofdm %x\n",
7058 sc->rxon->chan, sc->rxon->flags, sc->rxon->cck_mask,
7059 sc->rxon->ofdm_mask);
7060 if (sc->sc_is_scanning)
7061 device_printf(sc->sc_dev,
7062 "%s: is_scanning set, before RXON\n",
7064 error = iwn_cmd(sc, IWN_CMD_RXON, sc->rxon, sc->rxonsz, 1);
7066 device_printf(sc->sc_dev, "%s: RXON command failed, error %d\n",
7071 /* Configuration has changed, set TX power accordingly. */
7072 if ((error = ops->set_txpower(sc, ni->ni_chan, 1)) != 0) {
7073 device_printf(sc->sc_dev,
7074 "%s: could not set TX power, error %d\n", __func__, error);
7078 * Reconfiguring RXON clears the firmware nodes table so we must
7079 * add the broadcast node again.
7081 if ((error = iwn_add_broadcast_node(sc, 1)) != 0) {
7082 device_printf(sc->sc_dev,
7083 "%s: could not add broadcast node, error %d\n", __func__,
7088 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
7094 iwn_run(struct iwn_softc *sc, struct ieee80211vap *vap)
7096 struct iwn_ops *ops = &sc->ops;
7097 struct ieee80211com *ic = &sc->sc_ic;
7098 struct ieee80211_node *ni = vap->iv_bss;
7099 struct iwn_node_info node;
7102 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
7104 sc->rxon = &sc->rx_on[IWN_RXON_BSS_CTX];
7105 if (ic->ic_opmode == IEEE80211_M_MONITOR) {
7106 /* Link LED blinks while monitoring. */
7107 iwn_set_led(sc, IWN_LED_LINK, 5, 5);
7110 if ((error = iwn_set_timing(sc, ni)) != 0) {
7111 device_printf(sc->sc_dev,
7112 "%s: could not set timing, error %d\n", __func__, error);
7116 /* Update adapter configuration. */
7117 IEEE80211_ADDR_COPY(sc->rxon->bssid, ni->ni_bssid);
7118 sc->rxon->associd = htole16(IEEE80211_AID(ni->ni_associd));
7119 sc->rxon->chan = ieee80211_chan2ieee(ic, ni->ni_chan);
7120 sc->rxon->flags = htole32(IWN_RXON_TSF | IWN_RXON_CTS_TO_SELF);
7121 if (IEEE80211_IS_CHAN_2GHZ(ni->ni_chan))
7122 sc->rxon->flags |= htole32(IWN_RXON_AUTO | IWN_RXON_24GHZ);
7123 if (ic->ic_flags & IEEE80211_F_SHSLOT)
7124 sc->rxon->flags |= htole32(IWN_RXON_SHSLOT);
7125 if (ic->ic_flags & IEEE80211_F_SHPREAMBLE)
7126 sc->rxon->flags |= htole32(IWN_RXON_SHPREAMBLE);
7127 if (IEEE80211_IS_CHAN_A(ni->ni_chan)) {
7128 sc->rxon->cck_mask = 0;
7129 sc->rxon->ofdm_mask = 0x15;
7130 } else if (IEEE80211_IS_CHAN_B(ni->ni_chan)) {
7131 sc->rxon->cck_mask = 0x03;
7132 sc->rxon->ofdm_mask = 0;
7134 /* Assume 802.11b/g. */
7135 sc->rxon->cck_mask = 0x0f;
7136 sc->rxon->ofdm_mask = 0x15;
7139 sc->rxon->flags |= htole32(iwn_get_rxon_ht_flags(sc, ni->ni_chan));
7140 sc->rxon->filter |= htole32(IWN_FILTER_BSS);
7141 DPRINTF(sc, IWN_DEBUG_STATE, "rxon chan %d flags %x, curhtprotmode=%d\n",
7142 sc->rxon->chan, le32toh(sc->rxon->flags), ic->ic_curhtprotmode);
7143 if (sc->sc_is_scanning)
7144 device_printf(sc->sc_dev,
7145 "%s: is_scanning set, before RXON\n",
7147 error = iwn_cmd(sc, IWN_CMD_RXON, sc->rxon, sc->rxonsz, 1);
7149 device_printf(sc->sc_dev,
7150 "%s: could not update configuration, error %d\n", __func__,
7155 /* Configuration has changed, set TX power accordingly. */
7156 if ((error = ops->set_txpower(sc, ni->ni_chan, 1)) != 0) {
7157 device_printf(sc->sc_dev,
7158 "%s: could not set TX power, error %d\n", __func__, error);
7162 /* Fake a join to initialize the TX rate. */
7163 ((struct iwn_node *)ni)->id = IWN_ID_BSS;
7164 iwn_newassoc(ni, 1);
7167 memset(&node, 0, sizeof node);
7168 IEEE80211_ADDR_COPY(node.macaddr, ni->ni_macaddr);
7169 node.id = IWN_ID_BSS;
7170 if (IEEE80211_IS_CHAN_HT(ni->ni_chan)) {
7171 switch (ni->ni_htcap & IEEE80211_HTCAP_SMPS) {
7172 case IEEE80211_HTCAP_SMPS_ENA:
7173 node.htflags |= htole32(IWN_SMPS_MIMO_DIS);
7175 case IEEE80211_HTCAP_SMPS_DYNAMIC:
7176 node.htflags |= htole32(IWN_SMPS_MIMO_PROT);
7179 node.htflags |= htole32(IWN_AMDPU_SIZE_FACTOR(3) |
7180 IWN_AMDPU_DENSITY(5)); /* 4us */
7181 if (IEEE80211_IS_CHAN_HT40(ni->ni_chan))
7182 node.htflags |= htole32(IWN_NODE_HT40);
7184 DPRINTF(sc, IWN_DEBUG_STATE, "%s: adding BSS node\n", __func__);
7185 error = ops->add_node(sc, &node, 1);
7187 device_printf(sc->sc_dev,
7188 "%s: could not add BSS node, error %d\n", __func__, error);
7191 DPRINTF(sc, IWN_DEBUG_STATE, "%s: setting link quality for node %d\n",
7193 if ((error = iwn_set_link_quality(sc, ni)) != 0) {
7194 device_printf(sc->sc_dev,
7195 "%s: could not setup link quality for node %d, error %d\n",
7196 __func__, node.id, error);
7200 if ((error = iwn_init_sensitivity(sc)) != 0) {
7201 device_printf(sc->sc_dev,
7202 "%s: could not set sensitivity, error %d\n", __func__,
7206 /* Start periodic calibration timer. */
7207 sc->calib.state = IWN_CALIB_STATE_ASSOC;
7209 callout_reset(&sc->calib_to, msecs_to_ticks(500), iwn_calib_timeout,
7212 /* Link LED always on while associated. */
7213 iwn_set_led(sc, IWN_LED_LINK, 0, 1);
7215 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
7221 * This function is called by upper layer when an ADDBA request is received
7222 * from another STA and before the ADDBA response is sent.
7225 iwn_ampdu_rx_start(struct ieee80211_node *ni, struct ieee80211_rx_ampdu *rap,
7226 int baparamset, int batimeout, int baseqctl)
7228 #define MS(_v, _f) (((_v) & _f) >> _f##_S)
7229 struct iwn_softc *sc = ni->ni_ic->ic_softc;
7230 struct iwn_ops *ops = &sc->ops;
7231 struct iwn_node *wn = (void *)ni;
7232 struct iwn_node_info node;
7237 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
7239 tid = MS(le16toh(baparamset), IEEE80211_BAPS_TID);
7240 ssn = MS(le16toh(baseqctl), IEEE80211_BASEQ_START);
7242 memset(&node, 0, sizeof node);
7244 node.control = IWN_NODE_UPDATE;
7245 node.flags = IWN_FLAG_SET_ADDBA;
7246 node.addba_tid = tid;
7247 node.addba_ssn = htole16(ssn);
7248 DPRINTF(sc, IWN_DEBUG_RECV, "ADDBA RA=%d TID=%d SSN=%d\n",
7250 error = ops->add_node(sc, &node, 1);
7253 return sc->sc_ampdu_rx_start(ni, rap, baparamset, batimeout, baseqctl);
7258 * This function is called by upper layer on teardown of an HT-immediate
7259 * Block Ack agreement (eg. uppon receipt of a DELBA frame).
7262 iwn_ampdu_rx_stop(struct ieee80211_node *ni, struct ieee80211_rx_ampdu *rap)
7264 struct ieee80211com *ic = ni->ni_ic;
7265 struct iwn_softc *sc = ic->ic_softc;
7266 struct iwn_ops *ops = &sc->ops;
7267 struct iwn_node *wn = (void *)ni;
7268 struct iwn_node_info node;
7271 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
7273 /* XXX: tid as an argument */
7274 for (tid = 0; tid < WME_NUM_TID; tid++) {
7275 if (&ni->ni_rx_ampdu[tid] == rap)
7279 memset(&node, 0, sizeof node);
7281 node.control = IWN_NODE_UPDATE;
7282 node.flags = IWN_FLAG_SET_DELBA;
7283 node.delba_tid = tid;
7284 DPRINTF(sc, IWN_DEBUG_RECV, "DELBA RA=%d TID=%d\n", wn->id, tid);
7285 (void)ops->add_node(sc, &node, 1);
7286 sc->sc_ampdu_rx_stop(ni, rap);
7290 iwn_addba_request(struct ieee80211_node *ni, struct ieee80211_tx_ampdu *tap,
7291 int dialogtoken, int baparamset, int batimeout)
7293 struct iwn_softc *sc = ni->ni_ic->ic_softc;
7296 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
7298 for (qid = sc->firstaggqueue; qid < sc->ntxqs; qid++) {
7299 if (sc->qid2tap[qid] == NULL)
7302 if (qid == sc->ntxqs) {
7303 DPRINTF(sc, IWN_DEBUG_XMIT, "%s: not free aggregation queue\n",
7307 tap->txa_private = malloc(sizeof(int), M_DEVBUF, M_NOWAIT);
7308 if (tap->txa_private == NULL) {
7309 device_printf(sc->sc_dev,
7310 "%s: failed to alloc TX aggregation structure\n", __func__);
7313 sc->qid2tap[qid] = tap;
7314 *(int *)tap->txa_private = qid;
7315 return sc->sc_addba_request(ni, tap, dialogtoken, baparamset,
7320 iwn_addba_response(struct ieee80211_node *ni, struct ieee80211_tx_ampdu *tap,
7321 int code, int baparamset, int batimeout)
7323 struct iwn_softc *sc = ni->ni_ic->ic_softc;
7324 int qid = *(int *)tap->txa_private;
7325 uint8_t tid = tap->txa_tid;
7328 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
7330 if (code == IEEE80211_STATUS_SUCCESS) {
7331 ni->ni_txseqs[tid] = tap->txa_start & 0xfff;
7332 ret = iwn_ampdu_tx_start(ni->ni_ic, ni, tid);
7336 sc->qid2tap[qid] = NULL;
7337 free(tap->txa_private, M_DEVBUF);
7338 tap->txa_private = NULL;
7340 return sc->sc_addba_response(ni, tap, code, baparamset, batimeout);
7344 * This function is called by upper layer when an ADDBA response is received
7348 iwn_ampdu_tx_start(struct ieee80211com *ic, struct ieee80211_node *ni,
7351 struct ieee80211_tx_ampdu *tap = &ni->ni_tx_ampdu[tid];
7352 struct iwn_softc *sc = ni->ni_ic->ic_softc;
7353 struct iwn_ops *ops = &sc->ops;
7354 struct iwn_node *wn = (void *)ni;
7355 struct iwn_node_info node;
7358 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
7360 /* Enable TX for the specified RA/TID. */
7361 wn->disable_tid &= ~(1 << tid);
7362 memset(&node, 0, sizeof node);
7364 node.control = IWN_NODE_UPDATE;
7365 node.flags = IWN_FLAG_SET_DISABLE_TID;
7366 node.disable_tid = htole16(wn->disable_tid);
7367 error = ops->add_node(sc, &node, 1);
7371 if ((error = iwn_nic_lock(sc)) != 0)
7373 qid = *(int *)tap->txa_private;
7374 DPRINTF(sc, IWN_DEBUG_XMIT, "%s: ra=%d tid=%d ssn=%d qid=%d\n",
7375 __func__, wn->id, tid, tap->txa_start, qid);
7376 ops->ampdu_tx_start(sc, ni, qid, tid, tap->txa_start & 0xfff);
7379 iwn_set_link_quality(sc, ni);
7384 iwn_ampdu_tx_stop(struct ieee80211_node *ni, struct ieee80211_tx_ampdu *tap)
7386 struct iwn_softc *sc = ni->ni_ic->ic_softc;
7387 struct iwn_ops *ops = &sc->ops;
7388 uint8_t tid = tap->txa_tid;
7391 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
7393 sc->sc_addba_stop(ni, tap);
7395 if (tap->txa_private == NULL)
7398 qid = *(int *)tap->txa_private;
7399 if (sc->txq[qid].queued != 0)
7401 if (iwn_nic_lock(sc) != 0)
7403 ops->ampdu_tx_stop(sc, qid, tid, tap->txa_start & 0xfff);
7405 sc->qid2tap[qid] = NULL;
7406 free(tap->txa_private, M_DEVBUF);
7407 tap->txa_private = NULL;
7411 iwn4965_ampdu_tx_start(struct iwn_softc *sc, struct ieee80211_node *ni,
7412 int qid, uint8_t tid, uint16_t ssn)
7414 struct iwn_node *wn = (void *)ni;
7416 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
7418 /* Stop TX scheduler while we're changing its configuration. */
7419 iwn_prph_write(sc, IWN4965_SCHED_QUEUE_STATUS(qid),
7420 IWN4965_TXQ_STATUS_CHGACT);
7422 /* Assign RA/TID translation to the queue. */
7423 iwn_mem_write_2(sc, sc->sched_base + IWN4965_SCHED_TRANS_TBL(qid),
7426 /* Enable chain-building mode for the queue. */
7427 iwn_prph_setbits(sc, IWN4965_SCHED_QCHAIN_SEL, 1 << qid);
7429 /* Set starting sequence number from the ADDBA request. */
7430 sc->txq[qid].cur = sc->txq[qid].read = (ssn & 0xff);
7431 IWN_WRITE(sc, IWN_HBUS_TARG_WRPTR, qid << 8 | (ssn & 0xff));
7432 iwn_prph_write(sc, IWN4965_SCHED_QUEUE_RDPTR(qid), ssn);
7434 /* Set scheduler window size. */
7435 iwn_mem_write(sc, sc->sched_base + IWN4965_SCHED_QUEUE_OFFSET(qid),
7437 /* Set scheduler frame limit. */
7438 iwn_mem_write(sc, sc->sched_base + IWN4965_SCHED_QUEUE_OFFSET(qid) + 4,
7439 IWN_SCHED_LIMIT << 16);
7441 /* Enable interrupts for the queue. */
7442 iwn_prph_setbits(sc, IWN4965_SCHED_INTR_MASK, 1 << qid);
7444 /* Mark the queue as active. */
7445 iwn_prph_write(sc, IWN4965_SCHED_QUEUE_STATUS(qid),
7446 IWN4965_TXQ_STATUS_ACTIVE | IWN4965_TXQ_STATUS_AGGR_ENA |
7447 iwn_tid2fifo[tid] << 1);
7451 iwn4965_ampdu_tx_stop(struct iwn_softc *sc, int qid, uint8_t tid, uint16_t ssn)
7453 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
7455 /* Stop TX scheduler while we're changing its configuration. */
7456 iwn_prph_write(sc, IWN4965_SCHED_QUEUE_STATUS(qid),
7457 IWN4965_TXQ_STATUS_CHGACT);
7459 /* Set starting sequence number from the ADDBA request. */
7460 IWN_WRITE(sc, IWN_HBUS_TARG_WRPTR, qid << 8 | (ssn & 0xff));
7461 iwn_prph_write(sc, IWN4965_SCHED_QUEUE_RDPTR(qid), ssn);
7463 /* Disable interrupts for the queue. */
7464 iwn_prph_clrbits(sc, IWN4965_SCHED_INTR_MASK, 1 << qid);
7466 /* Mark the queue as inactive. */
7467 iwn_prph_write(sc, IWN4965_SCHED_QUEUE_STATUS(qid),
7468 IWN4965_TXQ_STATUS_INACTIVE | iwn_tid2fifo[tid] << 1);
7472 iwn5000_ampdu_tx_start(struct iwn_softc *sc, struct ieee80211_node *ni,
7473 int qid, uint8_t tid, uint16_t ssn)
7475 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
7477 struct iwn_node *wn = (void *)ni;
7479 /* Stop TX scheduler while we're changing its configuration. */
7480 iwn_prph_write(sc, IWN5000_SCHED_QUEUE_STATUS(qid),
7481 IWN5000_TXQ_STATUS_CHGACT);
7483 /* Assign RA/TID translation to the queue. */
7484 iwn_mem_write_2(sc, sc->sched_base + IWN5000_SCHED_TRANS_TBL(qid),
7487 /* Enable chain-building mode for the queue. */
7488 iwn_prph_setbits(sc, IWN5000_SCHED_QCHAIN_SEL, 1 << qid);
7490 /* Enable aggregation for the queue. */
7491 iwn_prph_setbits(sc, IWN5000_SCHED_AGGR_SEL, 1 << qid);
7493 /* Set starting sequence number from the ADDBA request. */
7494 sc->txq[qid].cur = sc->txq[qid].read = (ssn & 0xff);
7495 IWN_WRITE(sc, IWN_HBUS_TARG_WRPTR, qid << 8 | (ssn & 0xff));
7496 iwn_prph_write(sc, IWN5000_SCHED_QUEUE_RDPTR(qid), ssn);
7498 /* Set scheduler window size and frame limit. */
7499 iwn_mem_write(sc, sc->sched_base + IWN5000_SCHED_QUEUE_OFFSET(qid) + 4,
7500 IWN_SCHED_LIMIT << 16 | IWN_SCHED_WINSZ);
7502 /* Enable interrupts for the queue. */
7503 iwn_prph_setbits(sc, IWN5000_SCHED_INTR_MASK, 1 << qid);
7505 /* Mark the queue as active. */
7506 iwn_prph_write(sc, IWN5000_SCHED_QUEUE_STATUS(qid),
7507 IWN5000_TXQ_STATUS_ACTIVE | iwn_tid2fifo[tid]);
7511 iwn5000_ampdu_tx_stop(struct iwn_softc *sc, int qid, uint8_t tid, uint16_t ssn)
7513 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
7515 /* Stop TX scheduler while we're changing its configuration. */
7516 iwn_prph_write(sc, IWN5000_SCHED_QUEUE_STATUS(qid),
7517 IWN5000_TXQ_STATUS_CHGACT);
7519 /* Disable aggregation for the queue. */
7520 iwn_prph_clrbits(sc, IWN5000_SCHED_AGGR_SEL, 1 << qid);
7522 /* Set starting sequence number from the ADDBA request. */
7523 IWN_WRITE(sc, IWN_HBUS_TARG_WRPTR, qid << 8 | (ssn & 0xff));
7524 iwn_prph_write(sc, IWN5000_SCHED_QUEUE_RDPTR(qid), ssn);
7526 /* Disable interrupts for the queue. */
7527 iwn_prph_clrbits(sc, IWN5000_SCHED_INTR_MASK, 1 << qid);
7529 /* Mark the queue as inactive. */
7530 iwn_prph_write(sc, IWN5000_SCHED_QUEUE_STATUS(qid),
7531 IWN5000_TXQ_STATUS_INACTIVE | iwn_tid2fifo[tid]);
7535 * Query calibration tables from the initialization firmware. We do this
7536 * only once at first boot. Called from a process context.
7539 iwn5000_query_calibration(struct iwn_softc *sc)
7541 struct iwn5000_calib_config cmd;
7544 memset(&cmd, 0, sizeof cmd);
7545 cmd.ucode.once.enable = htole32(0xffffffff);
7546 cmd.ucode.once.start = htole32(0xffffffff);
7547 cmd.ucode.once.send = htole32(0xffffffff);
7548 cmd.ucode.flags = htole32(0xffffffff);
7549 DPRINTF(sc, IWN_DEBUG_CALIBRATE, "%s: sending calibration query\n",
7551 error = iwn_cmd(sc, IWN5000_CMD_CALIB_CONFIG, &cmd, sizeof cmd, 0);
7555 /* Wait at most two seconds for calibration to complete. */
7556 if (!(sc->sc_flags & IWN_FLAG_CALIB_DONE))
7557 error = msleep(sc, &sc->sc_mtx, PCATCH, "iwncal", 2 * hz);
7562 * Send calibration results to the runtime firmware. These results were
7563 * obtained on first boot from the initialization firmware.
7566 iwn5000_send_calibration(struct iwn_softc *sc)
7570 for (idx = 0; idx < IWN5000_PHY_CALIB_MAX_RESULT; idx++) {
7571 if (!(sc->base_params->calib_need & (1<<idx))) {
7572 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
7573 "No need of calib %d\n",
7575 continue; /* no need for this calib */
7577 if (sc->calibcmd[idx].buf == NULL) {
7578 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
7579 "Need calib idx : %d but no available data\n",
7584 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
7585 "send calibration result idx=%d len=%d\n", idx,
7586 sc->calibcmd[idx].len);
7587 error = iwn_cmd(sc, IWN_CMD_PHY_CALIB, sc->calibcmd[idx].buf,
7588 sc->calibcmd[idx].len, 0);
7590 device_printf(sc->sc_dev,
7591 "%s: could not send calibration result, error %d\n",
7600 iwn5000_send_wimax_coex(struct iwn_softc *sc)
7602 struct iwn5000_wimax_coex wimax;
7605 if (sc->hw_type == IWN_HW_REV_TYPE_6050) {
7606 /* Enable WiMAX coexistence for combo adapters. */
7608 IWN_WIMAX_COEX_ASSOC_WA_UNMASK |
7609 IWN_WIMAX_COEX_UNASSOC_WA_UNMASK |
7610 IWN_WIMAX_COEX_STA_TABLE_VALID |
7611 IWN_WIMAX_COEX_ENABLE;
7612 memcpy(wimax.events, iwn6050_wimax_events,
7613 sizeof iwn6050_wimax_events);
7617 /* Disable WiMAX coexistence. */
7619 memset(wimax.events, 0, sizeof wimax.events);
7621 DPRINTF(sc, IWN_DEBUG_RESET, "%s: Configuring WiMAX coexistence\n",
7623 return iwn_cmd(sc, IWN5000_CMD_WIMAX_COEX, &wimax, sizeof wimax, 0);
7627 iwn5000_crystal_calib(struct iwn_softc *sc)
7629 struct iwn5000_phy_calib_crystal cmd;
7631 memset(&cmd, 0, sizeof cmd);
7632 cmd.code = IWN5000_PHY_CALIB_CRYSTAL;
7635 cmd.cap_pin[0] = le32toh(sc->eeprom_crystal) & 0xff;
7636 cmd.cap_pin[1] = (le32toh(sc->eeprom_crystal) >> 16) & 0xff;
7637 DPRINTF(sc, IWN_DEBUG_CALIBRATE, "sending crystal calibration %d, %d\n",
7638 cmd.cap_pin[0], cmd.cap_pin[1]);
7639 return iwn_cmd(sc, IWN_CMD_PHY_CALIB, &cmd, sizeof cmd, 0);
7643 iwn5000_temp_offset_calib(struct iwn_softc *sc)
7645 struct iwn5000_phy_calib_temp_offset cmd;
7647 memset(&cmd, 0, sizeof cmd);
7648 cmd.code = IWN5000_PHY_CALIB_TEMP_OFFSET;
7651 if (sc->eeprom_temp != 0)
7652 cmd.offset = htole16(sc->eeprom_temp);
7654 cmd.offset = htole16(IWN_DEFAULT_TEMP_OFFSET);
7655 DPRINTF(sc, IWN_DEBUG_CALIBRATE, "setting radio sensor offset to %d\n",
7656 le16toh(cmd.offset));
7657 return iwn_cmd(sc, IWN_CMD_PHY_CALIB, &cmd, sizeof cmd, 0);
7661 iwn5000_temp_offset_calibv2(struct iwn_softc *sc)
7663 struct iwn5000_phy_calib_temp_offsetv2 cmd;
7665 memset(&cmd, 0, sizeof cmd);
7666 cmd.code = IWN5000_PHY_CALIB_TEMP_OFFSET;
7669 if (sc->eeprom_temp != 0) {
7670 cmd.offset_low = htole16(sc->eeprom_temp);
7671 cmd.offset_high = htole16(sc->eeprom_temp_high);
7673 cmd.offset_low = htole16(IWN_DEFAULT_TEMP_OFFSET);
7674 cmd.offset_high = htole16(IWN_DEFAULT_TEMP_OFFSET);
7676 cmd.burnt_voltage_ref = htole16(sc->eeprom_voltage);
7678 DPRINTF(sc, IWN_DEBUG_CALIBRATE,
7679 "setting radio sensor low offset to %d, high offset to %d, voltage to %d\n",
7680 le16toh(cmd.offset_low),
7681 le16toh(cmd.offset_high),
7682 le16toh(cmd.burnt_voltage_ref));
7684 return iwn_cmd(sc, IWN_CMD_PHY_CALIB, &cmd, sizeof cmd, 0);
7688 * This function is called after the runtime firmware notifies us of its
7689 * readiness (called in a process context).
7692 iwn4965_post_alive(struct iwn_softc *sc)
7696 if ((error = iwn_nic_lock(sc)) != 0)
7699 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
7701 /* Clear TX scheduler state in SRAM. */
7702 sc->sched_base = iwn_prph_read(sc, IWN_SCHED_SRAM_ADDR);
7703 iwn_mem_set_region_4(sc, sc->sched_base + IWN4965_SCHED_CTX_OFF, 0,
7704 IWN4965_SCHED_CTX_LEN / sizeof (uint32_t));
7706 /* Set physical address of TX scheduler rings (1KB aligned). */
7707 iwn_prph_write(sc, IWN4965_SCHED_DRAM_ADDR, sc->sched_dma.paddr >> 10);
7709 IWN_SETBITS(sc, IWN_FH_TX_CHICKEN, IWN_FH_TX_CHICKEN_SCHED_RETRY);
7711 /* Disable chain mode for all our 16 queues. */
7712 iwn_prph_write(sc, IWN4965_SCHED_QCHAIN_SEL, 0);
7714 for (qid = 0; qid < IWN4965_NTXQUEUES; qid++) {
7715 iwn_prph_write(sc, IWN4965_SCHED_QUEUE_RDPTR(qid), 0);
7716 IWN_WRITE(sc, IWN_HBUS_TARG_WRPTR, qid << 8 | 0);
7718 /* Set scheduler window size. */
7719 iwn_mem_write(sc, sc->sched_base +
7720 IWN4965_SCHED_QUEUE_OFFSET(qid), IWN_SCHED_WINSZ);
7721 /* Set scheduler frame limit. */
7722 iwn_mem_write(sc, sc->sched_base +
7723 IWN4965_SCHED_QUEUE_OFFSET(qid) + 4,
7724 IWN_SCHED_LIMIT << 16);
7727 /* Enable interrupts for all our 16 queues. */
7728 iwn_prph_write(sc, IWN4965_SCHED_INTR_MASK, 0xffff);
7729 /* Identify TX FIFO rings (0-7). */
7730 iwn_prph_write(sc, IWN4965_SCHED_TXFACT, 0xff);
7732 /* Mark TX rings (4 EDCA + cmd + 2 HCCA) as active. */
7733 for (qid = 0; qid < 7; qid++) {
7734 static uint8_t qid2fifo[] = { 3, 2, 1, 0, 4, 5, 6 };
7735 iwn_prph_write(sc, IWN4965_SCHED_QUEUE_STATUS(qid),
7736 IWN4965_TXQ_STATUS_ACTIVE | qid2fifo[qid] << 1);
7743 * This function is called after the initialization or runtime firmware
7744 * notifies us of its readiness (called in a process context).
7747 iwn5000_post_alive(struct iwn_softc *sc)
7751 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
7753 /* Switch to using ICT interrupt mode. */
7754 iwn5000_ict_reset(sc);
7756 if ((error = iwn_nic_lock(sc)) != 0){
7757 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s end in error\n", __func__);
7761 /* Clear TX scheduler state in SRAM. */
7762 sc->sched_base = iwn_prph_read(sc, IWN_SCHED_SRAM_ADDR);
7763 iwn_mem_set_region_4(sc, sc->sched_base + IWN5000_SCHED_CTX_OFF, 0,
7764 IWN5000_SCHED_CTX_LEN / sizeof (uint32_t));
7766 /* Set physical address of TX scheduler rings (1KB aligned). */
7767 iwn_prph_write(sc, IWN5000_SCHED_DRAM_ADDR, sc->sched_dma.paddr >> 10);
7769 IWN_SETBITS(sc, IWN_FH_TX_CHICKEN, IWN_FH_TX_CHICKEN_SCHED_RETRY);
7771 /* Enable chain mode for all queues, except command queue. */
7772 if (sc->sc_flags & IWN_FLAG_PAN_SUPPORT)
7773 iwn_prph_write(sc, IWN5000_SCHED_QCHAIN_SEL, 0xfffdf);
7775 iwn_prph_write(sc, IWN5000_SCHED_QCHAIN_SEL, 0xfffef);
7776 iwn_prph_write(sc, IWN5000_SCHED_AGGR_SEL, 0);
7778 for (qid = 0; qid < IWN5000_NTXQUEUES; qid++) {
7779 iwn_prph_write(sc, IWN5000_SCHED_QUEUE_RDPTR(qid), 0);
7780 IWN_WRITE(sc, IWN_HBUS_TARG_WRPTR, qid << 8 | 0);
7782 iwn_mem_write(sc, sc->sched_base +
7783 IWN5000_SCHED_QUEUE_OFFSET(qid), 0);
7784 /* Set scheduler window size and frame limit. */
7785 iwn_mem_write(sc, sc->sched_base +
7786 IWN5000_SCHED_QUEUE_OFFSET(qid) + 4,
7787 IWN_SCHED_LIMIT << 16 | IWN_SCHED_WINSZ);
7790 /* Enable interrupts for all our 20 queues. */
7791 iwn_prph_write(sc, IWN5000_SCHED_INTR_MASK, 0xfffff);
7792 /* Identify TX FIFO rings (0-7). */
7793 iwn_prph_write(sc, IWN5000_SCHED_TXFACT, 0xff);
7795 /* Mark TX rings (4 EDCA + cmd + 2 HCCA) as active. */
7796 if (sc->sc_flags & IWN_FLAG_PAN_SUPPORT) {
7797 /* Mark TX rings as active. */
7798 for (qid = 0; qid < 11; qid++) {
7799 static uint8_t qid2fifo[] = { 3, 2, 1, 0, 0, 4, 2, 5, 4, 7, 5 };
7800 iwn_prph_write(sc, IWN5000_SCHED_QUEUE_STATUS(qid),
7801 IWN5000_TXQ_STATUS_ACTIVE | qid2fifo[qid]);
7804 /* Mark TX rings (4 EDCA + cmd + 2 HCCA) as active. */
7805 for (qid = 0; qid < 7; qid++) {
7806 static uint8_t qid2fifo[] = { 3, 2, 1, 0, 7, 5, 6 };
7807 iwn_prph_write(sc, IWN5000_SCHED_QUEUE_STATUS(qid),
7808 IWN5000_TXQ_STATUS_ACTIVE | qid2fifo[qid]);
7813 /* Configure WiMAX coexistence for combo adapters. */
7814 error = iwn5000_send_wimax_coex(sc);
7816 device_printf(sc->sc_dev,
7817 "%s: could not configure WiMAX coexistence, error %d\n",
7821 if (sc->hw_type != IWN_HW_REV_TYPE_5150) {
7822 /* Perform crystal calibration. */
7823 error = iwn5000_crystal_calib(sc);
7825 device_printf(sc->sc_dev,
7826 "%s: crystal calibration failed, error %d\n",
7831 if (!(sc->sc_flags & IWN_FLAG_CALIB_DONE)) {
7832 /* Query calibration from the initialization firmware. */
7833 if ((error = iwn5000_query_calibration(sc)) != 0) {
7834 device_printf(sc->sc_dev,
7835 "%s: could not query calibration, error %d\n",
7840 * We have the calibration results now, reboot with the
7841 * runtime firmware (call ourselves recursively!)
7844 error = iwn_hw_init(sc);
7846 /* Send calibration results to runtime firmware. */
7847 error = iwn5000_send_calibration(sc);
7850 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
7856 * The firmware boot code is small and is intended to be copied directly into
7857 * the NIC internal memory (no DMA transfer).
7860 iwn4965_load_bootcode(struct iwn_softc *sc, const uint8_t *ucode, int size)
7864 size /= sizeof (uint32_t);
7866 if ((error = iwn_nic_lock(sc)) != 0)
7869 /* Copy microcode image into NIC memory. */
7870 iwn_prph_write_region_4(sc, IWN_BSM_SRAM_BASE,
7871 (const uint32_t *)ucode, size);
7873 iwn_prph_write(sc, IWN_BSM_WR_MEM_SRC, 0);
7874 iwn_prph_write(sc, IWN_BSM_WR_MEM_DST, IWN_FW_TEXT_BASE);
7875 iwn_prph_write(sc, IWN_BSM_WR_DWCOUNT, size);
7877 /* Start boot load now. */
7878 iwn_prph_write(sc, IWN_BSM_WR_CTRL, IWN_BSM_WR_CTRL_START);
7880 /* Wait for transfer to complete. */
7881 for (ntries = 0; ntries < 1000; ntries++) {
7882 if (!(iwn_prph_read(sc, IWN_BSM_WR_CTRL) &
7883 IWN_BSM_WR_CTRL_START))
7887 if (ntries == 1000) {
7888 device_printf(sc->sc_dev, "%s: could not load boot firmware\n",
7894 /* Enable boot after power up. */
7895 iwn_prph_write(sc, IWN_BSM_WR_CTRL, IWN_BSM_WR_CTRL_START_EN);
7902 iwn4965_load_firmware(struct iwn_softc *sc)
7904 struct iwn_fw_info *fw = &sc->fw;
7905 struct iwn_dma_info *dma = &sc->fw_dma;
7908 /* Copy initialization sections into pre-allocated DMA-safe memory. */
7909 memcpy(dma->vaddr, fw->init.data, fw->init.datasz);
7910 bus_dmamap_sync(dma->tag, dma->map, BUS_DMASYNC_PREWRITE);
7911 memcpy(dma->vaddr + IWN4965_FW_DATA_MAXSZ,
7912 fw->init.text, fw->init.textsz);
7913 bus_dmamap_sync(dma->tag, dma->map, BUS_DMASYNC_PREWRITE);
7915 /* Tell adapter where to find initialization sections. */
7916 if ((error = iwn_nic_lock(sc)) != 0)
7918 iwn_prph_write(sc, IWN_BSM_DRAM_DATA_ADDR, dma->paddr >> 4);
7919 iwn_prph_write(sc, IWN_BSM_DRAM_DATA_SIZE, fw->init.datasz);
7920 iwn_prph_write(sc, IWN_BSM_DRAM_TEXT_ADDR,
7921 (dma->paddr + IWN4965_FW_DATA_MAXSZ) >> 4);
7922 iwn_prph_write(sc, IWN_BSM_DRAM_TEXT_SIZE, fw->init.textsz);
7925 /* Load firmware boot code. */
7926 error = iwn4965_load_bootcode(sc, fw->boot.text, fw->boot.textsz);
7928 device_printf(sc->sc_dev, "%s: could not load boot firmware\n",
7932 /* Now press "execute". */
7933 IWN_WRITE(sc, IWN_RESET, 0);
7935 /* Wait at most one second for first alive notification. */
7936 if ((error = msleep(sc, &sc->sc_mtx, PCATCH, "iwninit", hz)) != 0) {
7937 device_printf(sc->sc_dev,
7938 "%s: timeout waiting for adapter to initialize, error %d\n",
7943 /* Retrieve current temperature for initial TX power calibration. */
7944 sc->rawtemp = sc->ucode_info.temp[3].chan20MHz;
7945 sc->temp = iwn4965_get_temperature(sc);
7947 /* Copy runtime sections into pre-allocated DMA-safe memory. */
7948 memcpy(dma->vaddr, fw->main.data, fw->main.datasz);
7949 bus_dmamap_sync(dma->tag, dma->map, BUS_DMASYNC_PREWRITE);
7950 memcpy(dma->vaddr + IWN4965_FW_DATA_MAXSZ,
7951 fw->main.text, fw->main.textsz);
7952 bus_dmamap_sync(dma->tag, dma->map, BUS_DMASYNC_PREWRITE);
7954 /* Tell adapter where to find runtime sections. */
7955 if ((error = iwn_nic_lock(sc)) != 0)
7957 iwn_prph_write(sc, IWN_BSM_DRAM_DATA_ADDR, dma->paddr >> 4);
7958 iwn_prph_write(sc, IWN_BSM_DRAM_DATA_SIZE, fw->main.datasz);
7959 iwn_prph_write(sc, IWN_BSM_DRAM_TEXT_ADDR,
7960 (dma->paddr + IWN4965_FW_DATA_MAXSZ) >> 4);
7961 iwn_prph_write(sc, IWN_BSM_DRAM_TEXT_SIZE,
7962 IWN_FW_UPDATED | fw->main.textsz);
7969 iwn5000_load_firmware_section(struct iwn_softc *sc, uint32_t dst,
7970 const uint8_t *section, int size)
7972 struct iwn_dma_info *dma = &sc->fw_dma;
7975 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
7977 /* Copy firmware section into pre-allocated DMA-safe memory. */
7978 memcpy(dma->vaddr, section, size);
7979 bus_dmamap_sync(dma->tag, dma->map, BUS_DMASYNC_PREWRITE);
7981 if ((error = iwn_nic_lock(sc)) != 0)
7984 IWN_WRITE(sc, IWN_FH_TX_CONFIG(IWN_SRVC_DMACHNL),
7985 IWN_FH_TX_CONFIG_DMA_PAUSE);
7987 IWN_WRITE(sc, IWN_FH_SRAM_ADDR(IWN_SRVC_DMACHNL), dst);
7988 IWN_WRITE(sc, IWN_FH_TFBD_CTRL0(IWN_SRVC_DMACHNL),
7989 IWN_LOADDR(dma->paddr));
7990 IWN_WRITE(sc, IWN_FH_TFBD_CTRL1(IWN_SRVC_DMACHNL),
7991 IWN_HIADDR(dma->paddr) << 28 | size);
7992 IWN_WRITE(sc, IWN_FH_TXBUF_STATUS(IWN_SRVC_DMACHNL),
7993 IWN_FH_TXBUF_STATUS_TBNUM(1) |
7994 IWN_FH_TXBUF_STATUS_TBIDX(1) |
7995 IWN_FH_TXBUF_STATUS_TFBD_VALID);
7997 /* Kick Flow Handler to start DMA transfer. */
7998 IWN_WRITE(sc, IWN_FH_TX_CONFIG(IWN_SRVC_DMACHNL),
7999 IWN_FH_TX_CONFIG_DMA_ENA | IWN_FH_TX_CONFIG_CIRQ_HOST_ENDTFD);
8003 /* Wait at most five seconds for FH DMA transfer to complete. */
8004 return msleep(sc, &sc->sc_mtx, PCATCH, "iwninit", 5 * hz);
8008 iwn5000_load_firmware(struct iwn_softc *sc)
8010 struct iwn_fw_part *fw;
8013 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
8015 /* Load the initialization firmware on first boot only. */
8016 fw = (sc->sc_flags & IWN_FLAG_CALIB_DONE) ?
8017 &sc->fw.main : &sc->fw.init;
8019 error = iwn5000_load_firmware_section(sc, IWN_FW_TEXT_BASE,
8020 fw->text, fw->textsz);
8022 device_printf(sc->sc_dev,
8023 "%s: could not load firmware %s section, error %d\n",
8024 __func__, ".text", error);
8027 error = iwn5000_load_firmware_section(sc, IWN_FW_DATA_BASE,
8028 fw->data, fw->datasz);
8030 device_printf(sc->sc_dev,
8031 "%s: could not load firmware %s section, error %d\n",
8032 __func__, ".data", error);
8036 /* Now press "execute". */
8037 IWN_WRITE(sc, IWN_RESET, 0);
8042 * Extract text and data sections from a legacy firmware image.
8045 iwn_read_firmware_leg(struct iwn_softc *sc, struct iwn_fw_info *fw)
8047 const uint32_t *ptr;
8051 ptr = (const uint32_t *)fw->data;
8052 rev = le32toh(*ptr++);
8054 sc->ucode_rev = rev;
8056 /* Check firmware API version. */
8057 if (IWN_FW_API(rev) <= 1) {
8058 device_printf(sc->sc_dev,
8059 "%s: bad firmware, need API version >=2\n", __func__);
8062 if (IWN_FW_API(rev) >= 3) {
8063 /* Skip build number (version 2 header). */
8067 if (fw->size < hdrlen) {
8068 device_printf(sc->sc_dev, "%s: firmware too short: %zu bytes\n",
8069 __func__, fw->size);
8072 fw->main.textsz = le32toh(*ptr++);
8073 fw->main.datasz = le32toh(*ptr++);
8074 fw->init.textsz = le32toh(*ptr++);
8075 fw->init.datasz = le32toh(*ptr++);
8076 fw->boot.textsz = le32toh(*ptr++);
8078 /* Check that all firmware sections fit. */
8079 if (fw->size < hdrlen + fw->main.textsz + fw->main.datasz +
8080 fw->init.textsz + fw->init.datasz + fw->boot.textsz) {
8081 device_printf(sc->sc_dev, "%s: firmware too short: %zu bytes\n",
8082 __func__, fw->size);
8086 /* Get pointers to firmware sections. */
8087 fw->main.text = (const uint8_t *)ptr;
8088 fw->main.data = fw->main.text + fw->main.textsz;
8089 fw->init.text = fw->main.data + fw->main.datasz;
8090 fw->init.data = fw->init.text + fw->init.textsz;
8091 fw->boot.text = fw->init.data + fw->init.datasz;
8096 * Extract text and data sections from a TLV firmware image.
8099 iwn_read_firmware_tlv(struct iwn_softc *sc, struct iwn_fw_info *fw,
8102 const struct iwn_fw_tlv_hdr *hdr;
8103 const struct iwn_fw_tlv *tlv;
8104 const uint8_t *ptr, *end;
8108 if (fw->size < sizeof (*hdr)) {
8109 device_printf(sc->sc_dev, "%s: firmware too short: %zu bytes\n",
8110 __func__, fw->size);
8113 hdr = (const struct iwn_fw_tlv_hdr *)fw->data;
8114 if (hdr->signature != htole32(IWN_FW_SIGNATURE)) {
8115 device_printf(sc->sc_dev, "%s: bad firmware signature 0x%08x\n",
8116 __func__, le32toh(hdr->signature));
8119 DPRINTF(sc, IWN_DEBUG_RESET, "FW: \"%.64s\", build 0x%x\n", hdr->descr,
8120 le32toh(hdr->build));
8121 sc->ucode_rev = le32toh(hdr->rev);
8124 * Select the closest supported alternative that is less than
8125 * or equal to the specified one.
8127 altmask = le64toh(hdr->altmask);
8128 while (alt > 0 && !(altmask & (1ULL << alt)))
8129 alt--; /* Downgrade. */
8130 DPRINTF(sc, IWN_DEBUG_RESET, "using alternative %d\n", alt);
8132 ptr = (const uint8_t *)(hdr + 1);
8133 end = (const uint8_t *)(fw->data + fw->size);
8135 /* Parse type-length-value fields. */
8136 while (ptr + sizeof (*tlv) <= end) {
8137 tlv = (const struct iwn_fw_tlv *)ptr;
8138 len = le32toh(tlv->len);
8140 ptr += sizeof (*tlv);
8141 if (ptr + len > end) {
8142 device_printf(sc->sc_dev,
8143 "%s: firmware too short: %zu bytes\n", __func__,
8147 /* Skip other alternatives. */
8148 if (tlv->alt != 0 && tlv->alt != htole16(alt))
8151 switch (le16toh(tlv->type)) {
8152 case IWN_FW_TLV_MAIN_TEXT:
8153 fw->main.text = ptr;
8154 fw->main.textsz = len;
8156 case IWN_FW_TLV_MAIN_DATA:
8157 fw->main.data = ptr;
8158 fw->main.datasz = len;
8160 case IWN_FW_TLV_INIT_TEXT:
8161 fw->init.text = ptr;
8162 fw->init.textsz = len;
8164 case IWN_FW_TLV_INIT_DATA:
8165 fw->init.data = ptr;
8166 fw->init.datasz = len;
8168 case IWN_FW_TLV_BOOT_TEXT:
8169 fw->boot.text = ptr;
8170 fw->boot.textsz = len;
8172 case IWN_FW_TLV_ENH_SENS:
8174 sc->sc_flags |= IWN_FLAG_ENH_SENS;
8176 case IWN_FW_TLV_PHY_CALIB:
8177 tmp = le32toh(*ptr);
8179 sc->reset_noise_gain = tmp;
8180 sc->noise_gain = tmp + 1;
8183 case IWN_FW_TLV_PAN:
8184 sc->sc_flags |= IWN_FLAG_PAN_SUPPORT;
8185 DPRINTF(sc, IWN_DEBUG_RESET,
8186 "PAN Support found: %d\n", 1);
8188 case IWN_FW_TLV_FLAGS:
8189 if (len < sizeof(uint32_t))
8191 if (len % sizeof(uint32_t))
8193 sc->tlv_feature_flags = le32toh(*ptr);
8194 DPRINTF(sc, IWN_DEBUG_RESET,
8195 "%s: feature: 0x%08x\n",
8197 sc->tlv_feature_flags);
8199 case IWN_FW_TLV_PBREQ_MAXLEN:
8200 case IWN_FW_TLV_RUNT_EVTLOG_PTR:
8201 case IWN_FW_TLV_RUNT_EVTLOG_SIZE:
8202 case IWN_FW_TLV_RUNT_ERRLOG_PTR:
8203 case IWN_FW_TLV_INIT_EVTLOG_PTR:
8204 case IWN_FW_TLV_INIT_EVTLOG_SIZE:
8205 case IWN_FW_TLV_INIT_ERRLOG_PTR:
8206 case IWN_FW_TLV_WOWLAN_INST:
8207 case IWN_FW_TLV_WOWLAN_DATA:
8208 DPRINTF(sc, IWN_DEBUG_RESET,
8209 "TLV type %d recognized but not handled\n",
8210 le16toh(tlv->type));
8213 DPRINTF(sc, IWN_DEBUG_RESET,
8214 "TLV type %d not handled\n", le16toh(tlv->type));
8217 next: /* TLV fields are 32-bit aligned. */
8218 ptr += (len + 3) & ~3;
8224 iwn_read_firmware(struct iwn_softc *sc)
8226 struct iwn_fw_info *fw = &sc->fw;
8229 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
8233 memset(fw, 0, sizeof (*fw));
8235 /* Read firmware image from filesystem. */
8236 sc->fw_fp = firmware_get(sc->fwname);
8237 if (sc->fw_fp == NULL) {
8238 device_printf(sc->sc_dev, "%s: could not read firmware %s\n",
8239 __func__, sc->fwname);
8245 fw->size = sc->fw_fp->datasize;
8246 fw->data = (const uint8_t *)sc->fw_fp->data;
8247 if (fw->size < sizeof (uint32_t)) {
8248 device_printf(sc->sc_dev, "%s: firmware too short: %zu bytes\n",
8249 __func__, fw->size);
8254 /* Retrieve text and data sections. */
8255 if (*(const uint32_t *)fw->data != 0) /* Legacy image. */
8256 error = iwn_read_firmware_leg(sc, fw);
8258 error = iwn_read_firmware_tlv(sc, fw, 1);
8260 device_printf(sc->sc_dev,
8261 "%s: could not read firmware sections, error %d\n",
8266 device_printf(sc->sc_dev, "%s: ucode rev=0x%08x\n", __func__, sc->ucode_rev);
8268 /* Make sure text and data sections fit in hardware memory. */
8269 if (fw->main.textsz > sc->fw_text_maxsz ||
8270 fw->main.datasz > sc->fw_data_maxsz ||
8271 fw->init.textsz > sc->fw_text_maxsz ||
8272 fw->init.datasz > sc->fw_data_maxsz ||
8273 fw->boot.textsz > IWN_FW_BOOT_TEXT_MAXSZ ||
8274 (fw->boot.textsz & 3) != 0) {
8275 device_printf(sc->sc_dev, "%s: firmware sections too large\n",
8281 /* We can proceed with loading the firmware. */
8284 fail: iwn_unload_firmware(sc);
8289 iwn_unload_firmware(struct iwn_softc *sc)
8291 firmware_put(sc->fw_fp, FIRMWARE_UNLOAD);
8296 iwn_clock_wait(struct iwn_softc *sc)
8300 /* Set "initialization complete" bit. */
8301 IWN_SETBITS(sc, IWN_GP_CNTRL, IWN_GP_CNTRL_INIT_DONE);
8303 /* Wait for clock stabilization. */
8304 for (ntries = 0; ntries < 2500; ntries++) {
8305 if (IWN_READ(sc, IWN_GP_CNTRL) & IWN_GP_CNTRL_MAC_CLOCK_READY)
8309 device_printf(sc->sc_dev,
8310 "%s: timeout waiting for clock stabilization\n", __func__);
8315 iwn_apm_init(struct iwn_softc *sc)
8320 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
8322 /* Disable L0s exit timer (NMI bug workaround). */
8323 IWN_SETBITS(sc, IWN_GIO_CHICKEN, IWN_GIO_CHICKEN_DIS_L0S_TIMER);
8324 /* Don't wait for ICH L0s (ICH bug workaround). */
8325 IWN_SETBITS(sc, IWN_GIO_CHICKEN, IWN_GIO_CHICKEN_L1A_NO_L0S_RX);
8327 /* Set FH wait threshold to max (HW bug under stress workaround). */
8328 IWN_SETBITS(sc, IWN_DBG_HPET_MEM, 0xffff0000);
8330 /* Enable HAP INTA to move adapter from L1a to L0s. */
8331 IWN_SETBITS(sc, IWN_HW_IF_CONFIG, IWN_HW_IF_CONFIG_HAP_WAKE_L1A);
8333 /* Retrieve PCIe Active State Power Management (ASPM). */
8334 reg = pci_read_config(sc->sc_dev, sc->sc_cap_off + PCIER_LINK_CTL, 4);
8335 /* Workaround for HW instability in PCIe L0->L0s->L1 transition. */
8336 if (reg & PCIEM_LINK_CTL_ASPMC_L1) /* L1 Entry enabled. */
8337 IWN_SETBITS(sc, IWN_GIO, IWN_GIO_L0S_ENA);
8339 IWN_CLRBITS(sc, IWN_GIO, IWN_GIO_L0S_ENA);
8341 if (sc->base_params->pll_cfg_val)
8342 IWN_SETBITS(sc, IWN_ANA_PLL, sc->base_params->pll_cfg_val);
8344 /* Wait for clock stabilization before accessing prph. */
8345 if ((error = iwn_clock_wait(sc)) != 0)
8348 if ((error = iwn_nic_lock(sc)) != 0)
8350 if (sc->hw_type == IWN_HW_REV_TYPE_4965) {
8351 /* Enable DMA and BSM (Bootstrap State Machine). */
8352 iwn_prph_write(sc, IWN_APMG_CLK_EN,
8353 IWN_APMG_CLK_CTRL_DMA_CLK_RQT |
8354 IWN_APMG_CLK_CTRL_BSM_CLK_RQT);
8357 iwn_prph_write(sc, IWN_APMG_CLK_EN,
8358 IWN_APMG_CLK_CTRL_DMA_CLK_RQT);
8361 /* Disable L1-Active. */
8362 iwn_prph_setbits(sc, IWN_APMG_PCI_STT, IWN_APMG_PCI_STT_L1A_DIS);
8369 iwn_apm_stop_master(struct iwn_softc *sc)
8373 /* Stop busmaster DMA activity. */
8374 IWN_SETBITS(sc, IWN_RESET, IWN_RESET_STOP_MASTER);
8375 for (ntries = 0; ntries < 100; ntries++) {
8376 if (IWN_READ(sc, IWN_RESET) & IWN_RESET_MASTER_DISABLED)
8380 device_printf(sc->sc_dev, "%s: timeout waiting for master\n", __func__);
8384 iwn_apm_stop(struct iwn_softc *sc)
8386 iwn_apm_stop_master(sc);
8388 /* Reset the entire device. */
8389 IWN_SETBITS(sc, IWN_RESET, IWN_RESET_SW);
8391 /* Clear "initialization complete" bit. */
8392 IWN_CLRBITS(sc, IWN_GP_CNTRL, IWN_GP_CNTRL_INIT_DONE);
8396 iwn4965_nic_config(struct iwn_softc *sc)
8398 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
8400 if (IWN_RFCFG_TYPE(sc->rfcfg) == 1) {
8402 * I don't believe this to be correct but this is what the
8403 * vendor driver is doing. Probably the bits should not be
8404 * shifted in IWN_RFCFG_*.
8406 IWN_SETBITS(sc, IWN_HW_IF_CONFIG,
8407 IWN_RFCFG_TYPE(sc->rfcfg) |
8408 IWN_RFCFG_STEP(sc->rfcfg) |
8409 IWN_RFCFG_DASH(sc->rfcfg));
8411 IWN_SETBITS(sc, IWN_HW_IF_CONFIG,
8412 IWN_HW_IF_CONFIG_RADIO_SI | IWN_HW_IF_CONFIG_MAC_SI);
8417 iwn5000_nic_config(struct iwn_softc *sc)
8422 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
8424 if (IWN_RFCFG_TYPE(sc->rfcfg) < 3) {
8425 IWN_SETBITS(sc, IWN_HW_IF_CONFIG,
8426 IWN_RFCFG_TYPE(sc->rfcfg) |
8427 IWN_RFCFG_STEP(sc->rfcfg) |
8428 IWN_RFCFG_DASH(sc->rfcfg));
8430 IWN_SETBITS(sc, IWN_HW_IF_CONFIG,
8431 IWN_HW_IF_CONFIG_RADIO_SI | IWN_HW_IF_CONFIG_MAC_SI);
8433 if ((error = iwn_nic_lock(sc)) != 0)
8435 iwn_prph_setbits(sc, IWN_APMG_PS, IWN_APMG_PS_EARLY_PWROFF_DIS);
8437 if (sc->hw_type == IWN_HW_REV_TYPE_1000) {
8439 * Select first Switching Voltage Regulator (1.32V) to
8440 * solve a stability issue related to noisy DC2DC line
8441 * in the silicon of 1000 Series.
8443 tmp = iwn_prph_read(sc, IWN_APMG_DIGITAL_SVR);
8444 tmp &= ~IWN_APMG_DIGITAL_SVR_VOLTAGE_MASK;
8445 tmp |= IWN_APMG_DIGITAL_SVR_VOLTAGE_1_32;
8446 iwn_prph_write(sc, IWN_APMG_DIGITAL_SVR, tmp);
8450 if (sc->sc_flags & IWN_FLAG_INTERNAL_PA) {
8451 /* Use internal power amplifier only. */
8452 IWN_WRITE(sc, IWN_GP_DRIVER, IWN_GP_DRIVER_RADIO_2X2_IPA);
8454 if (sc->base_params->additional_nic_config && sc->calib_ver >= 6) {
8455 /* Indicate that ROM calibration version is >=6. */
8456 IWN_SETBITS(sc, IWN_GP_DRIVER, IWN_GP_DRIVER_CALIB_VER6);
8458 if (sc->base_params->additional_gp_drv_bit)
8459 IWN_SETBITS(sc, IWN_GP_DRIVER,
8460 sc->base_params->additional_gp_drv_bit);
8465 * Take NIC ownership over Intel Active Management Technology (AMT).
8468 iwn_hw_prepare(struct iwn_softc *sc)
8472 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
8474 /* Check if hardware is ready. */
8475 IWN_SETBITS(sc, IWN_HW_IF_CONFIG, IWN_HW_IF_CONFIG_NIC_READY);
8476 for (ntries = 0; ntries < 5; ntries++) {
8477 if (IWN_READ(sc, IWN_HW_IF_CONFIG) &
8478 IWN_HW_IF_CONFIG_NIC_READY)
8483 /* Hardware not ready, force into ready state. */
8484 IWN_SETBITS(sc, IWN_HW_IF_CONFIG, IWN_HW_IF_CONFIG_PREPARE);
8485 for (ntries = 0; ntries < 15000; ntries++) {
8486 if (!(IWN_READ(sc, IWN_HW_IF_CONFIG) &
8487 IWN_HW_IF_CONFIG_PREPARE_DONE))
8491 if (ntries == 15000)
8494 /* Hardware should be ready now. */
8495 IWN_SETBITS(sc, IWN_HW_IF_CONFIG, IWN_HW_IF_CONFIG_NIC_READY);
8496 for (ntries = 0; ntries < 5; ntries++) {
8497 if (IWN_READ(sc, IWN_HW_IF_CONFIG) &
8498 IWN_HW_IF_CONFIG_NIC_READY)
8506 iwn_hw_init(struct iwn_softc *sc)
8508 struct iwn_ops *ops = &sc->ops;
8509 int error, chnl, qid;
8511 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
8513 /* Clear pending interrupts. */
8514 IWN_WRITE(sc, IWN_INT, 0xffffffff);
8516 if ((error = iwn_apm_init(sc)) != 0) {
8517 device_printf(sc->sc_dev,
8518 "%s: could not power ON adapter, error %d\n", __func__,
8523 /* Select VMAIN power source. */
8524 if ((error = iwn_nic_lock(sc)) != 0)
8526 iwn_prph_clrbits(sc, IWN_APMG_PS, IWN_APMG_PS_PWR_SRC_MASK);
8529 /* Perform adapter-specific initialization. */
8530 if ((error = ops->nic_config(sc)) != 0)
8533 /* Initialize RX ring. */
8534 if ((error = iwn_nic_lock(sc)) != 0)
8536 IWN_WRITE(sc, IWN_FH_RX_CONFIG, 0);
8537 IWN_WRITE(sc, IWN_FH_RX_WPTR, 0);
8538 /* Set physical address of RX ring (256-byte aligned). */
8539 IWN_WRITE(sc, IWN_FH_RX_BASE, sc->rxq.desc_dma.paddr >> 8);
8540 /* Set physical address of RX status (16-byte aligned). */
8541 IWN_WRITE(sc, IWN_FH_STATUS_WPTR, sc->rxq.stat_dma.paddr >> 4);
8543 IWN_WRITE(sc, IWN_FH_RX_CONFIG,
8544 IWN_FH_RX_CONFIG_ENA |
8545 IWN_FH_RX_CONFIG_IGN_RXF_EMPTY | /* HW bug workaround */
8546 IWN_FH_RX_CONFIG_IRQ_DST_HOST |
8547 IWN_FH_RX_CONFIG_SINGLE_FRAME |
8548 IWN_FH_RX_CONFIG_RB_TIMEOUT(0) |
8549 IWN_FH_RX_CONFIG_NRBD(IWN_RX_RING_COUNT_LOG));
8551 IWN_WRITE(sc, IWN_FH_RX_WPTR, (IWN_RX_RING_COUNT - 1) & ~7);
8553 if ((error = iwn_nic_lock(sc)) != 0)
8556 /* Initialize TX scheduler. */
8557 iwn_prph_write(sc, sc->sched_txfact_addr, 0);
8559 /* Set physical address of "keep warm" page (16-byte aligned). */
8560 IWN_WRITE(sc, IWN_FH_KW_ADDR, sc->kw_dma.paddr >> 4);
8562 /* Initialize TX rings. */
8563 for (qid = 0; qid < sc->ntxqs; qid++) {
8564 struct iwn_tx_ring *txq = &sc->txq[qid];
8566 /* Set physical address of TX ring (256-byte aligned). */
8567 IWN_WRITE(sc, IWN_FH_CBBC_QUEUE(qid),
8568 txq->desc_dma.paddr >> 8);
8572 /* Enable DMA channels. */
8573 for (chnl = 0; chnl < sc->ndmachnls; chnl++) {
8574 IWN_WRITE(sc, IWN_FH_TX_CONFIG(chnl),
8575 IWN_FH_TX_CONFIG_DMA_ENA |
8576 IWN_FH_TX_CONFIG_DMA_CREDIT_ENA);
8579 /* Clear "radio off" and "commands blocked" bits. */
8580 IWN_WRITE(sc, IWN_UCODE_GP1_CLR, IWN_UCODE_GP1_RFKILL);
8581 IWN_WRITE(sc, IWN_UCODE_GP1_CLR, IWN_UCODE_GP1_CMD_BLOCKED);
8583 /* Clear pending interrupts. */
8584 IWN_WRITE(sc, IWN_INT, 0xffffffff);
8585 /* Enable interrupt coalescing. */
8586 IWN_WRITE(sc, IWN_INT_COALESCING, 512 / 8);
8587 /* Enable interrupts. */
8588 IWN_WRITE(sc, IWN_INT_MASK, sc->int_mask);
8590 /* _Really_ make sure "radio off" bit is cleared! */
8591 IWN_WRITE(sc, IWN_UCODE_GP1_CLR, IWN_UCODE_GP1_RFKILL);
8592 IWN_WRITE(sc, IWN_UCODE_GP1_CLR, IWN_UCODE_GP1_RFKILL);
8594 /* Enable shadow registers. */
8595 if (sc->base_params->shadow_reg_enable)
8596 IWN_SETBITS(sc, IWN_SHADOW_REG_CTRL, 0x800fffff);
8598 if ((error = ops->load_firmware(sc)) != 0) {
8599 device_printf(sc->sc_dev,
8600 "%s: could not load firmware, error %d\n", __func__,
8604 /* Wait at most one second for firmware alive notification. */
8605 if ((error = msleep(sc, &sc->sc_mtx, PCATCH, "iwninit", hz)) != 0) {
8606 device_printf(sc->sc_dev,
8607 "%s: timeout waiting for adapter to initialize, error %d\n",
8611 /* Do post-firmware initialization. */
8613 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
8615 return ops->post_alive(sc);
8619 iwn_hw_stop(struct iwn_softc *sc)
8621 int chnl, qid, ntries;
8623 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
8625 IWN_WRITE(sc, IWN_RESET, IWN_RESET_NEVO);
8627 /* Disable interrupts. */
8628 IWN_WRITE(sc, IWN_INT_MASK, 0);
8629 IWN_WRITE(sc, IWN_INT, 0xffffffff);
8630 IWN_WRITE(sc, IWN_FH_INT, 0xffffffff);
8631 sc->sc_flags &= ~IWN_FLAG_USE_ICT;
8633 /* Make sure we no longer hold the NIC lock. */
8636 /* Stop TX scheduler. */
8637 iwn_prph_write(sc, sc->sched_txfact_addr, 0);
8639 /* Stop all DMA channels. */
8640 if (iwn_nic_lock(sc) == 0) {
8641 for (chnl = 0; chnl < sc->ndmachnls; chnl++) {
8642 IWN_WRITE(sc, IWN_FH_TX_CONFIG(chnl), 0);
8643 for (ntries = 0; ntries < 200; ntries++) {
8644 if (IWN_READ(sc, IWN_FH_TX_STATUS) &
8645 IWN_FH_TX_STATUS_IDLE(chnl))
8654 iwn_reset_rx_ring(sc, &sc->rxq);
8656 /* Reset all TX rings. */
8657 for (qid = 0; qid < sc->ntxqs; qid++)
8658 iwn_reset_tx_ring(sc, &sc->txq[qid]);
8660 if (iwn_nic_lock(sc) == 0) {
8661 iwn_prph_write(sc, IWN_APMG_CLK_DIS,
8662 IWN_APMG_CLK_CTRL_DMA_CLK_RQT);
8666 /* Power OFF adapter. */
8671 iwn_radio_on(void *arg0, int pending)
8673 struct iwn_softc *sc = arg0;
8674 struct ieee80211com *ic = &sc->sc_ic;
8675 struct ieee80211vap *vap = TAILQ_FIRST(&ic->ic_vaps);
8677 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
8681 ieee80211_init(vap);
8686 iwn_radio_off(void *arg0, int pending)
8688 struct iwn_softc *sc = arg0;
8689 struct ieee80211com *ic = &sc->sc_ic;
8690 struct ieee80211vap *vap = TAILQ_FIRST(&ic->ic_vaps);
8692 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
8696 ieee80211_stop(vap);
8698 /* Enable interrupts to get RF toggle notification. */
8700 IWN_WRITE(sc, IWN_INT, 0xffffffff);
8701 IWN_WRITE(sc, IWN_INT_MASK, sc->int_mask);
8706 iwn_panicked(void *arg0, int pending)
8708 struct iwn_softc *sc = arg0;
8709 struct ieee80211com *ic = &sc->sc_ic;
8710 struct ieee80211vap *vap = TAILQ_FIRST(&ic->ic_vaps);
8716 printf("%s: null vap\n", __func__);
8720 device_printf(sc->sc_dev, "%s: controller panicked, iv_state = %d; "
8721 "restarting\n", __func__, vap->iv_state);
8724 * This is not enough work. We need to also reinitialise
8725 * the correct transmit state for aggregation enabled queues,
8726 * which has a very specific requirement of
8727 * ring index = 802.11 seqno % 256. If we don't do this (which
8728 * we definitely don't!) then the firmware will just panic again.
8731 ieee80211_restart_all(ic);
8735 iwn_stop_locked(sc);
8736 iwn_init_locked(sc);
8737 if (vap->iv_state >= IEEE80211_S_AUTH &&
8738 (error = iwn_auth(sc, vap)) != 0) {
8739 device_printf(sc->sc_dev,
8740 "%s: could not move to auth state\n", __func__);
8742 if (vap->iv_state >= IEEE80211_S_RUN &&
8743 (error = iwn_run(sc, vap)) != 0) {
8744 device_printf(sc->sc_dev,
8745 "%s: could not move to run state\n", __func__);
8753 iwn_init_locked(struct iwn_softc *sc)
8757 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s begin\n", __func__);
8759 IWN_LOCK_ASSERT(sc);
8761 sc->sc_flags |= IWN_FLAG_RUNNING;
8763 if ((error = iwn_hw_prepare(sc)) != 0) {
8764 device_printf(sc->sc_dev, "%s: hardware not ready, error %d\n",
8769 /* Initialize interrupt mask to default value. */
8770 sc->int_mask = IWN_INT_MASK_DEF;
8771 sc->sc_flags &= ~IWN_FLAG_USE_ICT;
8773 /* Check that the radio is not disabled by hardware switch. */
8774 if (!(IWN_READ(sc, IWN_GP_CNTRL) & IWN_GP_CNTRL_RFKILL)) {
8775 device_printf(sc->sc_dev,
8776 "radio is disabled by hardware switch\n");
8777 /* Enable interrupts to get RF toggle notifications. */
8778 IWN_WRITE(sc, IWN_INT, 0xffffffff);
8779 IWN_WRITE(sc, IWN_INT_MASK, sc->int_mask);
8783 /* Read firmware images from the filesystem. */
8784 if ((error = iwn_read_firmware(sc)) != 0) {
8785 device_printf(sc->sc_dev,
8786 "%s: could not read firmware, error %d\n", __func__,
8791 /* Initialize hardware and upload firmware. */
8792 error = iwn_hw_init(sc);
8793 iwn_unload_firmware(sc);
8795 device_printf(sc->sc_dev,
8796 "%s: could not initialize hardware, error %d\n", __func__,
8801 /* Configure adapter now that it is ready. */
8802 if ((error = iwn_config(sc)) != 0) {
8803 device_printf(sc->sc_dev,
8804 "%s: could not configure device, error %d\n", __func__,
8809 callout_reset(&sc->watchdog_to, hz, iwn_watchdog, sc);
8811 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end\n",__func__);
8816 sc->sc_flags &= ~IWN_FLAG_RUNNING;
8817 iwn_stop_locked(sc);
8818 DPRINTF(sc, IWN_DEBUG_TRACE, "->%s: end in error\n",__func__);
8822 iwn_init(struct iwn_softc *sc)
8826 iwn_init_locked(sc);
8829 if (sc->sc_flags & IWN_FLAG_RUNNING)
8830 ieee80211_start_all(&sc->sc_ic);
8834 iwn_stop_locked(struct iwn_softc *sc)
8837 IWN_LOCK_ASSERT(sc);
8839 sc->sc_is_scanning = 0;
8840 sc->sc_tx_timer = 0;
8841 callout_stop(&sc->watchdog_to);
8842 callout_stop(&sc->scan_timeout);
8843 callout_stop(&sc->calib_to);
8844 sc->sc_flags &= ~IWN_FLAG_RUNNING;
8846 /* Power OFF hardware. */
8851 iwn_stop(struct iwn_softc *sc)
8854 iwn_stop_locked(sc);
8859 * Callback from net80211 to start a scan.
8862 iwn_scan_start(struct ieee80211com *ic)
8864 struct iwn_softc *sc = ic->ic_softc;
8867 /* make the link LED blink while we're scanning */
8868 iwn_set_led(sc, IWN_LED_LINK, 20, 2);
8873 * Callback from net80211 to terminate a scan.
8876 iwn_scan_end(struct ieee80211com *ic)
8878 struct iwn_softc *sc = ic->ic_softc;
8879 struct ieee80211vap *vap = TAILQ_FIRST(&ic->ic_vaps);
8882 if (vap->iv_state == IEEE80211_S_RUN) {
8883 /* Set link LED to ON status if we are associated */
8884 iwn_set_led(sc, IWN_LED_LINK, 0, 1);
8890 * Callback from net80211 to force a channel change.
8893 iwn_set_channel(struct ieee80211com *ic)
8895 const struct ieee80211_channel *c = ic->ic_curchan;
8896 struct iwn_softc *sc = ic->ic_softc;
8899 DPRINTF(sc, IWN_DEBUG_TRACE, "->Doing %s\n", __func__);
8902 sc->sc_rxtap.wr_chan_freq = htole16(c->ic_freq);
8903 sc->sc_rxtap.wr_chan_flags = htole16(c->ic_flags);
8904 sc->sc_txtap.wt_chan_freq = htole16(c->ic_freq);
8905 sc->sc_txtap.wt_chan_flags = htole16(c->ic_flags);
8908 * Only need to set the channel in Monitor mode. AP scanning and auth
8909 * are already taken care of by their respective firmware commands.
8911 if (ic->ic_opmode == IEEE80211_M_MONITOR) {
8912 error = iwn_config(sc);
8914 device_printf(sc->sc_dev,
8915 "%s: error %d settting channel\n", __func__, error);
8921 * Callback from net80211 to start scanning of the current channel.
8924 iwn_scan_curchan(struct ieee80211_scan_state *ss, unsigned long maxdwell)
8926 struct ieee80211vap *vap = ss->ss_vap;
8927 struct ieee80211com *ic = vap->iv_ic;
8928 struct iwn_softc *sc = ic->ic_softc;
8932 error = iwn_scan(sc, vap, ss, ic->ic_curchan);
8935 ieee80211_cancel_scan(vap);
8939 * Callback from net80211 to handle the minimum dwell time being met.
8940 * The intent is to terminate the scan but we just let the firmware
8941 * notify us when it's finished as we have no safe way to abort it.
8944 iwn_scan_mindwell(struct ieee80211_scan_state *ss)
8946 /* NB: don't try to abort scan; wait for firmware to finish */
8949 #define IWN_DESC(x) case x: return #x
8952 * Translate CSR code to string
8954 static char *iwn_get_csr_string(int csr)
8957 IWN_DESC(IWN_HW_IF_CONFIG);
8958 IWN_DESC(IWN_INT_COALESCING);
8960 IWN_DESC(IWN_INT_MASK);
8961 IWN_DESC(IWN_FH_INT);
8962 IWN_DESC(IWN_GPIO_IN);
8963 IWN_DESC(IWN_RESET);
8964 IWN_DESC(IWN_GP_CNTRL);
8965 IWN_DESC(IWN_HW_REV);
8966 IWN_DESC(IWN_EEPROM);
8967 IWN_DESC(IWN_EEPROM_GP);
8968 IWN_DESC(IWN_OTP_GP);
8970 IWN_DESC(IWN_GP_UCODE);
8971 IWN_DESC(IWN_GP_DRIVER);
8972 IWN_DESC(IWN_UCODE_GP1);
8973 IWN_DESC(IWN_UCODE_GP2);
8975 IWN_DESC(IWN_DRAM_INT_TBL);
8976 IWN_DESC(IWN_GIO_CHICKEN);
8977 IWN_DESC(IWN_ANA_PLL);
8978 IWN_DESC(IWN_HW_REV_WA);
8979 IWN_DESC(IWN_DBG_HPET_MEM);
8981 return "UNKNOWN CSR";
8986 * This function print firmware register
8989 iwn_debug_register(struct iwn_softc *sc)
8992 static const uint32_t csr_tbl[] = {
9017 DPRINTF(sc, IWN_DEBUG_REGISTER,
9018 "CSR values: (2nd byte of IWN_INT_COALESCING is IWN_INT_PERIODIC)%s",
9020 for (i = 0; i < nitems(csr_tbl); i++){
9021 DPRINTF(sc, IWN_DEBUG_REGISTER," %10s: 0x%08x ",
9022 iwn_get_csr_string(csr_tbl[i]), IWN_READ(sc, csr_tbl[i]));
9024 DPRINTF(sc, IWN_DEBUG_REGISTER,"%s","\n");
9026 DPRINTF(sc, IWN_DEBUG_REGISTER,"%s","\n");