2 * Copyright (c) 2011-2015 LSI Corp.
3 * Copyright (c) 2013-2016 Avago Technologies
6 * Redistribution and use in source and binary forms, with or without
7 * modification, are permitted provided that the following conditions
9 * 1. Redistributions of source code must retain the above copyright
10 * notice, this list of conditions and the following disclaimer.
11 * 2. Redistributions in binary form must reproduce the above copyright
12 * notice, this list of conditions and the following disclaimer in the
13 * documentation and/or other materials provided with the distribution.
15 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
16 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
17 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
18 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
19 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
20 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
21 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
22 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
23 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
24 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
27 * Avago Technologies (LSI) MPT-Fusion Host Adapter FreeBSD
30 #include <sys/cdefs.h>
31 __FBSDID("$FreeBSD$");
33 /* Communications core for Avago Technologies (LSI) MPT3 */
35 /* TODO Move headers to mprvar */
36 #include <sys/types.h>
37 #include <sys/param.h>
38 #include <sys/systm.h>
39 #include <sys/kernel.h>
40 #include <sys/selinfo.h>
41 #include <sys/module.h>
45 #include <sys/malloc.h>
47 #include <sys/sysctl.h>
48 #include <sys/endian.h>
49 #include <sys/queue.h>
50 #include <sys/kthread.h>
51 #include <sys/taskqueue.h>
54 #include <machine/bus.h>
55 #include <machine/resource.h>
58 #include <machine/stdarg.h>
61 #include <cam/cam_ccb.h>
62 #include <cam/cam_debug.h>
63 #include <cam/cam_sim.h>
64 #include <cam/cam_xpt_sim.h>
65 #include <cam/cam_xpt_periph.h>
66 #include <cam/cam_periph.h>
67 #include <cam/scsi/scsi_all.h>
68 #include <cam/scsi/scsi_message.h>
70 #include <dev/mpr/mpi/mpi2_type.h>
71 #include <dev/mpr/mpi/mpi2.h>
72 #include <dev/mpr/mpi/mpi2_ioc.h>
73 #include <dev/mpr/mpi/mpi2_sas.h>
74 #include <dev/mpr/mpi/mpi2_pci.h>
75 #include <dev/mpr/mpi/mpi2_cnfg.h>
76 #include <dev/mpr/mpi/mpi2_init.h>
77 #include <dev/mpr/mpi/mpi2_raid.h>
78 #include <dev/mpr/mpi/mpi2_tool.h>
79 #include <dev/mpr/mpr_ioctl.h>
80 #include <dev/mpr/mprvar.h>
81 #include <dev/mpr/mpr_table.h>
82 #include <dev/mpr/mpr_sas.h>
84 /* For Hashed SAS Address creation for SATA Drives */
85 #define MPT2SAS_SN_LEN 20
86 #define MPT2SAS_MN_LEN 40
88 struct mpr_fw_event_work {
91 TAILQ_ENTRY(mpr_fw_event_work) ev_link;
94 union _sata_sas_address {
103 * define the IDENTIFY DEVICE structure
105 struct _ata_identify_device_data {
106 u16 reserved1[10]; /* 0-9 */
107 u16 serial_number[10]; /* 10-19 */
108 u16 reserved2[7]; /* 20-26 */
109 u16 model_number[20]; /* 27-46*/
110 u16 reserved3[170]; /* 47-216 */
111 u16 rotational_speed; /* 217 */
112 u16 reserved4[38]; /* 218-255 */
114 static u32 event_count;
115 static void mprsas_fw_work(struct mpr_softc *sc,
116 struct mpr_fw_event_work *fw_event);
117 static void mprsas_fw_event_free(struct mpr_softc *,
118 struct mpr_fw_event_work *);
119 static int mprsas_add_device(struct mpr_softc *sc, u16 handle, u8 linkrate);
120 static int mprsas_add_pcie_device(struct mpr_softc *sc, u16 handle,
122 static int mprsas_get_sata_identify(struct mpr_softc *sc, u16 handle,
123 Mpi2SataPassthroughReply_t *mpi_reply, char *id_buffer, int sz,
125 static void mprsas_ata_id_timeout(void *data);
126 int mprsas_get_sas_address_for_sata_disk(struct mpr_softc *sc,
127 u64 *sas_address, u16 handle, u32 device_info, u8 *is_SATA_SSD);
128 static int mprsas_volume_add(struct mpr_softc *sc,
130 static void mprsas_SSU_to_SATA_devices(struct mpr_softc *sc);
131 static void mprsas_stop_unit_done(struct cam_periph *periph,
132 union ccb *done_ccb);
135 mprsas_evt_handler(struct mpr_softc *sc, uintptr_t data,
136 MPI2_EVENT_NOTIFICATION_REPLY *event)
138 struct mpr_fw_event_work *fw_event;
141 mpr_dprint(sc, MPR_TRACE, "%s\n", __func__);
142 mpr_print_evt_sas(sc, event);
143 mprsas_record_event(sc, event);
145 fw_event = malloc(sizeof(struct mpr_fw_event_work), M_MPR,
148 printf("%s: allocate failed for fw_event\n", __func__);
151 sz = le16toh(event->EventDataLength) * 4;
152 fw_event->event_data = malloc(sz, M_MPR, M_ZERO|M_NOWAIT);
153 if (!fw_event->event_data) {
154 printf("%s: allocate failed for event_data\n", __func__);
155 free(fw_event, M_MPR);
159 bcopy(event->EventData, fw_event->event_data, sz);
160 fw_event->event = event->Event;
161 if ((event->Event == MPI2_EVENT_SAS_TOPOLOGY_CHANGE_LIST ||
162 event->Event == MPI2_EVENT_PCIE_TOPOLOGY_CHANGE_LIST ||
163 event->Event == MPI2_EVENT_SAS_ENCL_DEVICE_STATUS_CHANGE ||
164 event->Event == MPI2_EVENT_IR_CONFIGURATION_CHANGE_LIST) &&
165 sc->track_mapping_events)
166 sc->pending_map_events++;
169 * When wait_for_port_enable flag is set, make sure that all the events
170 * are processed. Increment the startup_refcount and decrement it after
171 * events are processed.
173 if ((event->Event == MPI2_EVENT_SAS_TOPOLOGY_CHANGE_LIST ||
174 event->Event == MPI2_EVENT_PCIE_TOPOLOGY_CHANGE_LIST ||
175 event->Event == MPI2_EVENT_IR_CONFIGURATION_CHANGE_LIST) &&
176 sc->wait_for_port_enable)
177 mprsas_startup_increment(sc->sassc);
179 TAILQ_INSERT_TAIL(&sc->sassc->ev_queue, fw_event, ev_link);
180 taskqueue_enqueue(sc->sassc->ev_tq, &sc->sassc->ev_task);
184 mprsas_fw_event_free(struct mpr_softc *sc, struct mpr_fw_event_work *fw_event)
187 free(fw_event->event_data, M_MPR);
188 free(fw_event, M_MPR);
192 * _mpr_fw_work - delayed task for processing firmware events
193 * @sc: per adapter object
194 * @fw_event: The fw_event_work object
200 mprsas_fw_work(struct mpr_softc *sc, struct mpr_fw_event_work *fw_event)
202 struct mprsas_softc *sassc;
205 mpr_dprint(sc, MPR_EVENT, "(%d)->(%s) Working on Event: [%x]\n",
206 event_count++, __func__, fw_event->event);
207 switch (fw_event->event) {
208 case MPI2_EVENT_SAS_TOPOLOGY_CHANGE_LIST:
210 MPI2_EVENT_DATA_SAS_TOPOLOGY_CHANGE_LIST *data;
211 MPI2_EVENT_SAS_TOPO_PHY_ENTRY *phy;
214 data = (MPI2_EVENT_DATA_SAS_TOPOLOGY_CHANGE_LIST *)
215 fw_event->event_data;
217 mpr_mapping_topology_change_event(sc, fw_event->event_data);
219 for (i = 0; i < data->NumEntries; i++) {
221 switch (phy->PhyStatus & MPI2_EVENT_SAS_TOPO_RC_MASK) {
222 case MPI2_EVENT_SAS_TOPO_RC_TARG_ADDED:
223 if (mprsas_add_device(sc,
224 le16toh(phy->AttachedDevHandle),
226 mpr_dprint(sc, MPR_ERROR, "%s: "
227 "failed to add device with handle "
229 le16toh(phy->AttachedDevHandle));
230 mprsas_prepare_remove(sassc, le16toh(
231 phy->AttachedDevHandle));
234 case MPI2_EVENT_SAS_TOPO_RC_TARG_NOT_RESPONDING:
235 mprsas_prepare_remove(sassc, le16toh(
236 phy->AttachedDevHandle));
238 case MPI2_EVENT_SAS_TOPO_RC_PHY_CHANGED:
239 case MPI2_EVENT_SAS_TOPO_RC_NO_CHANGE:
240 case MPI2_EVENT_SAS_TOPO_RC_DELAY_NOT_RESPONDING:
246 * refcount was incremented for this event in
247 * mprsas_evt_handler. Decrement it here because the event has
250 mprsas_startup_decrement(sassc);
253 case MPI2_EVENT_SAS_DISCOVERY:
255 MPI2_EVENT_DATA_SAS_DISCOVERY *data;
257 data = (MPI2_EVENT_DATA_SAS_DISCOVERY *)fw_event->event_data;
259 if (data->ReasonCode & MPI2_EVENT_SAS_DISC_RC_STARTED)
260 mpr_dprint(sc, MPR_TRACE,"SAS discovery start event\n");
261 if (data->ReasonCode & MPI2_EVENT_SAS_DISC_RC_COMPLETED) {
262 mpr_dprint(sc, MPR_TRACE,"SAS discovery stop event\n");
263 sassc->flags &= ~MPRSAS_IN_DISCOVERY;
264 mprsas_discovery_end(sassc);
268 case MPI2_EVENT_SAS_ENCL_DEVICE_STATUS_CHANGE:
270 Mpi2EventDataSasEnclDevStatusChange_t *data;
271 data = (Mpi2EventDataSasEnclDevStatusChange_t *)
272 fw_event->event_data;
273 mpr_mapping_enclosure_dev_status_change_event(sc,
274 fw_event->event_data);
277 case MPI2_EVENT_IR_CONFIGURATION_CHANGE_LIST:
279 Mpi2EventIrConfigElement_t *element;
281 u8 foreign_config, reason;
283 Mpi2EventDataIrConfigChangeList_t *event_data;
284 struct mprsas_target *targ;
287 event_data = fw_event->event_data;
288 foreign_config = (le32toh(event_data->Flags) &
289 MPI2_EVENT_IR_CHANGE_FLAGS_FOREIGN_CONFIG) ? 1 : 0;
292 (Mpi2EventIrConfigElement_t *)&event_data->ConfigElement[0];
293 id = mpr_mapping_get_raid_tid_from_handle(sc,
294 element->VolDevHandle);
296 mpr_mapping_ir_config_change_event(sc, event_data);
297 for (i = 0; i < event_data->NumElements; i++, element++) {
298 reason = element->ReasonCode;
299 elementType = le16toh(element->ElementFlags) &
300 MPI2_EVENT_IR_CHANGE_EFLAGS_ELEMENT_TYPE_MASK;
302 * check for element type of Phys Disk or Hot Spare
305 MPI2_EVENT_IR_CHANGE_EFLAGS_VOLPHYSDISK_ELEMENT)
307 MPI2_EVENT_IR_CHANGE_EFLAGS_HOTSPARE_ELEMENT))
312 * check for reason of Hide, Unhide, PD Created, or PD
315 if ((reason != MPI2_EVENT_IR_CHANGE_RC_HIDE) &&
316 (reason != MPI2_EVENT_IR_CHANGE_RC_UNHIDE) &&
317 (reason != MPI2_EVENT_IR_CHANGE_RC_PD_CREATED) &&
318 (reason != MPI2_EVENT_IR_CHANGE_RC_PD_DELETED))
321 // check for a reason of Hide or PD Created
322 if ((reason == MPI2_EVENT_IR_CHANGE_RC_HIDE) ||
323 (reason == MPI2_EVENT_IR_CHANGE_RC_PD_CREATED))
325 // build RAID Action message
326 Mpi2RaidActionRequest_t *action;
327 Mpi2RaidActionReply_t *reply;
328 struct mpr_command *cm;
330 if ((cm = mpr_alloc_command(sc)) == NULL) {
331 printf("%s: command alloc failed\n",
336 mpr_dprint(sc, MPR_EVENT, "Sending FP action "
338 "MPI2_EVENT_IR_CONFIGURATION_CHANGE_LIST "
340 action = (MPI2_RAID_ACTION_REQUEST *)cm->cm_req;
341 action->Function = MPI2_FUNCTION_RAID_ACTION;
343 MPI2_RAID_ACTION_PHYSDISK_HIDDEN;
344 action->PhysDiskNum = element->PhysDiskNum;
345 cm->cm_desc.Default.RequestFlags =
346 MPI2_REQ_DESCRIPT_FLAGS_DEFAULT_TYPE;
347 error = mpr_request_polled(sc, cm);
348 reply = (Mpi2RaidActionReply_t *)cm->cm_reply;
349 if (error || (reply == NULL)) {
352 * If the poll returns error then we
353 * need to do diag reset
355 printf("%s: poll for page completed "
356 "with error %d", __func__, error);
358 if (reply && (le16toh(reply->IOCStatus) &
359 MPI2_IOCSTATUS_MASK) !=
360 MPI2_IOCSTATUS_SUCCESS) {
361 mpr_dprint(sc, MPR_ERROR, "%s: error "
362 "sending RaidActionPage; "
363 "iocstatus = 0x%x\n", __func__,
364 le16toh(reply->IOCStatus));
368 mpr_free_command(sc, cm);
371 mpr_dprint(sc, MPR_EVENT, "Received "
372 "MPI2_EVENT_IR_CONFIGURATION_CHANGE_LIST Reason "
373 "code %x:\n", element->ReasonCode);
374 switch (element->ReasonCode) {
375 case MPI2_EVENT_IR_CHANGE_RC_VOLUME_CREATED:
376 case MPI2_EVENT_IR_CHANGE_RC_ADDED:
377 if (!foreign_config) {
378 if (mprsas_volume_add(sc,
379 le16toh(element->VolDevHandle))) {
380 printf("%s: failed to add RAID "
381 "volume with handle 0x%x\n",
382 __func__, le16toh(element->
387 case MPI2_EVENT_IR_CHANGE_RC_VOLUME_DELETED:
388 case MPI2_EVENT_IR_CHANGE_RC_REMOVED:
390 * Rescan after volume is deleted or removed.
392 if (!foreign_config) {
393 if (id == MPR_MAP_BAD_ID) {
394 printf("%s: could not get ID "
395 "for volume with handle "
396 "0x%04x\n", __func__,
402 targ = &sassc->targets[id];
404 targ->encl_slot = 0x0;
405 targ->encl_handle = 0x0;
406 targ->encl_level_valid = 0x0;
407 targ->encl_level = 0x0;
408 targ->connector_name[0] = ' ';
409 targ->connector_name[1] = ' ';
410 targ->connector_name[2] = ' ';
411 targ->connector_name[3] = ' ';
412 targ->exp_dev_handle = 0x0;
414 targ->linkrate = 0x0;
415 mprsas_rescan_target(sc, targ);
416 printf("RAID target id 0x%x removed\n",
420 case MPI2_EVENT_IR_CHANGE_RC_PD_CREATED:
421 case MPI2_EVENT_IR_CHANGE_RC_HIDE:
423 * Phys Disk of a volume has been created. Hide
426 targ = mprsas_find_target_by_handle(sassc, 0,
427 element->PhysDiskDevHandle);
430 targ->flags |= MPR_TARGET_FLAGS_RAID_COMPONENT;
431 mprsas_rescan_target(sc, targ);
433 case MPI2_EVENT_IR_CHANGE_RC_PD_DELETED:
435 * Phys Disk of a volume has been deleted.
436 * Expose it to the OS.
438 if (mprsas_add_device(sc,
439 le16toh(element->PhysDiskDevHandle), 0)) {
440 printf("%s: failed to add device with "
441 "handle 0x%x\n", __func__,
444 mprsas_prepare_remove(sassc,
452 * refcount was incremented for this event in
453 * mprsas_evt_handler. Decrement it here because the event has
456 mprsas_startup_decrement(sassc);
459 case MPI2_EVENT_IR_VOLUME:
461 Mpi2EventDataIrVolume_t *event_data = fw_event->event_data;
464 * Informational only.
466 mpr_dprint(sc, MPR_EVENT, "Received IR Volume event:\n");
467 switch (event_data->ReasonCode) {
468 case MPI2_EVENT_IR_VOLUME_RC_SETTINGS_CHANGED:
469 mpr_dprint(sc, MPR_EVENT, " Volume Settings "
470 "changed from 0x%x to 0x%x for Volome with "
471 "handle 0x%x", le32toh(event_data->PreviousValue),
472 le32toh(event_data->NewValue),
473 le16toh(event_data->VolDevHandle));
475 case MPI2_EVENT_IR_VOLUME_RC_STATUS_FLAGS_CHANGED:
476 mpr_dprint(sc, MPR_EVENT, " Volume Status "
477 "changed from 0x%x to 0x%x for Volome with "
478 "handle 0x%x", le32toh(event_data->PreviousValue),
479 le32toh(event_data->NewValue),
480 le16toh(event_data->VolDevHandle));
482 case MPI2_EVENT_IR_VOLUME_RC_STATE_CHANGED:
483 mpr_dprint(sc, MPR_EVENT, " Volume State "
484 "changed from 0x%x to 0x%x for Volome with "
485 "handle 0x%x", le32toh(event_data->PreviousValue),
486 le32toh(event_data->NewValue),
487 le16toh(event_data->VolDevHandle));
489 struct mprsas_target *targ;
490 state = le32toh(event_data->NewValue);
492 case MPI2_RAID_VOL_STATE_MISSING:
493 case MPI2_RAID_VOL_STATE_FAILED:
494 mprsas_prepare_volume_remove(sassc,
495 event_data->VolDevHandle);
498 case MPI2_RAID_VOL_STATE_ONLINE:
499 case MPI2_RAID_VOL_STATE_DEGRADED:
500 case MPI2_RAID_VOL_STATE_OPTIMAL:
502 mprsas_find_target_by_handle(sassc,
503 0, event_data->VolDevHandle);
505 printf("%s %d: Volume handle "
506 "0x%x is already added \n",
508 event_data->VolDevHandle);
511 if (mprsas_volume_add(sc,
514 printf("%s: failed to add RAID "
515 "volume with handle 0x%x\n",
517 event_data->VolDevHandle));
529 case MPI2_EVENT_IR_PHYSICAL_DISK:
531 Mpi2EventDataIrPhysicalDisk_t *event_data =
532 fw_event->event_data;
533 struct mprsas_target *targ;
536 * Informational only.
538 mpr_dprint(sc, MPR_EVENT, "Received IR Phys Disk event:\n");
539 switch (event_data->ReasonCode) {
540 case MPI2_EVENT_IR_PHYSDISK_RC_SETTINGS_CHANGED:
541 mpr_dprint(sc, MPR_EVENT, " Phys Disk Settings "
542 "changed from 0x%x to 0x%x for Phys Disk Number "
543 "%d and handle 0x%x at Enclosure handle 0x%x, Slot "
544 "%d", le32toh(event_data->PreviousValue),
545 le32toh(event_data->NewValue),
546 event_data->PhysDiskNum,
547 le16toh(event_data->PhysDiskDevHandle),
548 le16toh(event_data->EnclosureHandle),
549 le16toh(event_data->Slot));
551 case MPI2_EVENT_IR_PHYSDISK_RC_STATUS_FLAGS_CHANGED:
552 mpr_dprint(sc, MPR_EVENT, " Phys Disk Status changed "
553 "from 0x%x to 0x%x for Phys Disk Number %d and "
554 "handle 0x%x at Enclosure handle 0x%x, Slot %d",
555 le32toh(event_data->PreviousValue),
556 le32toh(event_data->NewValue),
557 event_data->PhysDiskNum,
558 le16toh(event_data->PhysDiskDevHandle),
559 le16toh(event_data->EnclosureHandle),
560 le16toh(event_data->Slot));
562 case MPI2_EVENT_IR_PHYSDISK_RC_STATE_CHANGED:
563 mpr_dprint(sc, MPR_EVENT, " Phys Disk State changed "
564 "from 0x%x to 0x%x for Phys Disk Number %d and "
565 "handle 0x%x at Enclosure handle 0x%x, Slot %d",
566 le32toh(event_data->PreviousValue),
567 le32toh(event_data->NewValue),
568 event_data->PhysDiskNum,
569 le16toh(event_data->PhysDiskDevHandle),
570 le16toh(event_data->EnclosureHandle),
571 le16toh(event_data->Slot));
572 switch (event_data->NewValue) {
573 case MPI2_RAID_PD_STATE_ONLINE:
574 case MPI2_RAID_PD_STATE_DEGRADED:
575 case MPI2_RAID_PD_STATE_REBUILDING:
576 case MPI2_RAID_PD_STATE_OPTIMAL:
577 case MPI2_RAID_PD_STATE_HOT_SPARE:
578 targ = mprsas_find_target_by_handle(
580 event_data->PhysDiskDevHandle);
583 MPR_TARGET_FLAGS_RAID_COMPONENT;
584 printf("%s %d: Found Target "
585 "for handle 0x%x.\n",
591 case MPI2_RAID_PD_STATE_OFFLINE:
592 case MPI2_RAID_PD_STATE_NOT_CONFIGURED:
593 case MPI2_RAID_PD_STATE_NOT_COMPATIBLE:
595 targ = mprsas_find_target_by_handle(
597 event_data->PhysDiskDevHandle);
600 ~MPR_TARGET_FLAGS_RAID_COMPONENT;
601 printf("%s %d: Found Target "
602 "for handle 0x%x. \n",
614 case MPI2_EVENT_IR_OPERATION_STATUS:
616 Mpi2EventDataIrOperationStatus_t *event_data =
617 fw_event->event_data;
620 * Informational only.
622 mpr_dprint(sc, MPR_EVENT, "Received IR Op Status event:\n");
623 mpr_dprint(sc, MPR_EVENT, " RAID Operation of %d is %d "
624 "percent complete for Volume with handle 0x%x",
625 event_data->RAIDOperation, event_data->PercentComplete,
626 le16toh(event_data->VolDevHandle));
629 case MPI2_EVENT_TEMP_THRESHOLD:
631 pMpi2EventDataTemperature_t temp_event;
633 temp_event = (pMpi2EventDataTemperature_t)fw_event->event_data;
636 * The Temp Sensor Count must be greater than the event's Sensor
637 * Num to be valid. If valid, print the temp thresholds that
638 * have been exceeded.
640 if (sc->iounit_pg8.NumSensors > temp_event->SensorNum) {
641 mpr_dprint(sc, MPR_FAULT, "Temperature Threshold flags "
642 "%s %s %s %s exceeded for Sensor: %d !!!\n",
643 ((temp_event->Status & 0x01) == 1) ? "0 " : " ",
644 ((temp_event->Status & 0x02) == 2) ? "1 " : " ",
645 ((temp_event->Status & 0x04) == 4) ? "2 " : " ",
646 ((temp_event->Status & 0x08) == 8) ? "3 " : " ",
647 temp_event->SensorNum);
648 mpr_dprint(sc, MPR_FAULT, "Current Temp in Celsius: "
649 "%d\n", temp_event->CurrentTemperature);
653 case MPI2_EVENT_ACTIVE_CABLE_EXCEPTION:
655 pMpi26EventDataActiveCableExcept_t ace_event_data;
657 (pMpi26EventDataActiveCableExcept_t)fw_event->event_data;
659 switch(ace_event_data->ReasonCode) {
660 case MPI26_EVENT_ACTIVE_CABLE_INSUFFICIENT_POWER:
662 mpr_printf(sc, "Currently a cable with "
663 "ReceptacleID %d cannot be powered and device "
664 "connected to this active cable will not be seen. "
665 "This active cable requires %d mW of power.\n",
666 ace_event_data->ReceptacleID,
667 ace_event_data->ActiveCablePowerRequirement);
670 case MPI26_EVENT_ACTIVE_CABLE_DEGRADED:
672 mpr_printf(sc, "Currently a cable with "
673 "ReceptacleID %d is not running at optimal speed "
674 "(12 Gb/s rate)\n", ace_event_data->ReceptacleID);
682 case MPI2_EVENT_PCIE_TOPOLOGY_CHANGE_LIST:
684 MPI26_EVENT_DATA_PCIE_TOPOLOGY_CHANGE_LIST *data;
685 MPI26_EVENT_PCIE_TOPO_PORT_ENTRY *port_entry;
686 uint8_t i, link_rate;
689 data = (MPI26_EVENT_DATA_PCIE_TOPOLOGY_CHANGE_LIST *)
690 fw_event->event_data;
692 mpr_mapping_pcie_topology_change_event(sc,
693 fw_event->event_data);
695 for (i = 0; i < data->NumEntries; i++) {
696 port_entry = &data->PortEntry[i];
697 handle = le16toh(port_entry->AttachedDevHandle);
698 link_rate = port_entry->CurrentPortInfo &
699 MPI26_EVENT_PCIE_TOPO_PI_RATE_MASK;
700 switch (port_entry->PortStatus) {
701 case MPI26_EVENT_PCIE_TOPO_PS_DEV_ADDED:
703 MPI26_EVENT_PCIE_TOPO_PI_RATE_2_5) {
704 mpr_dprint(sc, MPR_ERROR, "%s: Cannot "
705 "add PCIe device with handle 0x%x "
706 "with unknown link rate.\n",
710 if (mprsas_add_pcie_device(sc, handle,
712 mpr_dprint(sc, MPR_ERROR, "%s: failed "
713 "to add PCIe device with handle "
714 "0x%x\n", __func__, handle);
715 mprsas_prepare_remove(sassc, handle);
718 case MPI26_EVENT_PCIE_TOPO_PS_NOT_RESPONDING:
719 mprsas_prepare_remove(sassc, handle);
721 case MPI26_EVENT_PCIE_TOPO_PS_PORT_CHANGED:
722 case MPI26_EVENT_PCIE_TOPO_PS_NO_CHANGE:
723 case MPI26_EVENT_PCIE_TOPO_PS_DELAY_NOT_RESPONDING:
729 * refcount was incremented for this event in
730 * mprsas_evt_handler. Decrement it here because the event has
733 mprsas_startup_decrement(sassc);
736 case MPI2_EVENT_SAS_DEVICE_STATUS_CHANGE:
737 case MPI2_EVENT_SAS_BROADCAST_PRIMITIVE:
739 mpr_dprint(sc, MPR_TRACE,"Unhandled event 0x%0X\n",
744 mpr_dprint(sc, MPR_EVENT, "(%d)->(%s) Event Free: [%x]\n", event_count,
745 __func__, fw_event->event);
746 mprsas_fw_event_free(sc, fw_event);
750 mprsas_firmware_event_work(void *arg, int pending)
752 struct mpr_fw_event_work *fw_event;
753 struct mpr_softc *sc;
755 sc = (struct mpr_softc *)arg;
757 while ((fw_event = TAILQ_FIRST(&sc->sassc->ev_queue)) != NULL) {
758 TAILQ_REMOVE(&sc->sassc->ev_queue, fw_event, ev_link);
759 mprsas_fw_work(sc, fw_event);
765 mprsas_add_device(struct mpr_softc *sc, u16 handle, u8 linkrate)
768 struct mprsas_softc *sassc;
769 struct mprsas_target *targ;
770 Mpi2ConfigReply_t mpi_reply;
771 Mpi2SasDevicePage0_t config_page;
772 uint64_t sas_address, parent_sas_address = 0;
773 u32 device_info, parent_devinfo = 0;
775 int ret = 1, error = 0, i;
776 struct mprsas_lun *lun;
778 struct mpr_command *cm;
781 mprsas_startup_increment(sassc);
782 if ((mpr_config_get_sas_device_pg0(sc, &mpi_reply, &config_page,
783 MPI2_SAS_DEVICE_PGAD_FORM_HANDLE, handle))) {
784 printf("%s: error reading SAS device page0\n", __func__);
789 device_info = le32toh(config_page.DeviceInfo);
791 if (((device_info & MPI2_SAS_DEVICE_INFO_SMP_TARGET) == 0)
792 && (le16toh(config_page.ParentDevHandle) != 0)) {
793 Mpi2ConfigReply_t tmp_mpi_reply;
794 Mpi2SasDevicePage0_t parent_config_page;
796 if ((mpr_config_get_sas_device_pg0(sc, &tmp_mpi_reply,
797 &parent_config_page, MPI2_SAS_DEVICE_PGAD_FORM_HANDLE,
798 le16toh(config_page.ParentDevHandle)))) {
799 printf("%s: error reading SAS device %#x page0\n",
800 __func__, le16toh(config_page.ParentDevHandle));
802 parent_sas_address = parent_config_page.SASAddress.High;
803 parent_sas_address = (parent_sas_address << 32) |
804 parent_config_page.SASAddress.Low;
805 parent_devinfo = le32toh(parent_config_page.DeviceInfo);
808 /* TODO Check proper endianness */
809 sas_address = config_page.SASAddress.High;
810 sas_address = (sas_address << 32) | config_page.SASAddress.Low;
811 mpr_dprint(sc, MPR_INFO, "SAS Address from SAS device page0 = %jx\n",
815 * Always get SATA Identify information because this is used to
816 * determine if Start/Stop Unit should be sent to the drive when the
817 * system is shutdown.
819 if (device_info & MPI2_SAS_DEVICE_INFO_SATA_DEVICE) {
820 ret = mprsas_get_sas_address_for_sata_disk(sc, &sas_address,
821 handle, device_info, &is_SATA_SSD);
823 mpr_dprint(sc, MPR_ERROR, "%s: failed to get disk type "
824 "(SSD or HDD) for SATA device with handle 0x%04x\n",
827 mpr_dprint(sc, MPR_INFO, "SAS Address from SATA "
828 "device = %jx\n", sas_address);
834 * 1 - use the PhyNum field as a fallback to the mapping logic
835 * 0 - never use the PhyNum field
836 * -1 - only use the PhyNum field
838 * Note that using the Phy number to map a device can cause device adds
839 * to fail if multiple enclosures/expanders are in the topology. For
840 * example, if two devices are in the same slot number in two different
841 * enclosures within the topology, only one of those devices will be
842 * added. PhyNum mapping should not be used if multiple enclosures are
846 if (sc->use_phynum != -1)
847 id = mpr_mapping_get_tid(sc, sas_address, handle);
848 if (id == MPR_MAP_BAD_ID) {
849 if ((sc->use_phynum == 0) ||
850 ((id = config_page.PhyNum) > sassc->maxtargets)) {
851 mpr_dprint(sc, MPR_INFO, "failure at %s:%d/%s()! "
852 "Could not get ID for device with handle 0x%04x\n",
853 __FILE__, __LINE__, __func__, handle);
858 mpr_dprint(sc, MPR_MAPPING, "%s: Target ID for added device is %d.\n",
862 * Only do the ID check and reuse check if the target is not from a
863 * RAID Component. For Physical Disks of a Volume, the ID will be reused
864 * when a volume is deleted because the mapping entry for the PD will
865 * still be in the mapping table. The ID check should not be done here
866 * either since this PD is already being used.
868 targ = &sassc->targets[id];
869 if (!(targ->flags & MPR_TARGET_FLAGS_RAID_COMPONENT)) {
870 if (mprsas_check_id(sassc, id) != 0) {
871 device_printf(sc->mpr_dev, "Excluding target id %d\n",
877 if (targ->handle != 0x0) {
878 mpr_dprint(sc, MPR_MAPPING, "Attempting to reuse "
879 "target id %d handle 0x%04x\n", id, targ->handle);
885 mpr_dprint(sc, MPR_MAPPING, "SAS Address from SAS device page0 = %jx\n",
887 targ->devinfo = device_info;
888 targ->devname = le32toh(config_page.DeviceName.High);
889 targ->devname = (targ->devname << 32) |
890 le32toh(config_page.DeviceName.Low);
891 targ->encl_handle = le16toh(config_page.EnclosureHandle);
892 targ->encl_slot = le16toh(config_page.Slot);
893 targ->encl_level = config_page.EnclosureLevel;
894 targ->connector_name[0] = config_page.ConnectorName[0];
895 targ->connector_name[1] = config_page.ConnectorName[1];
896 targ->connector_name[2] = config_page.ConnectorName[2];
897 targ->connector_name[3] = config_page.ConnectorName[3];
898 targ->handle = handle;
899 targ->parent_handle = le16toh(config_page.ParentDevHandle);
900 targ->sasaddr = mpr_to_u64(&config_page.SASAddress);
901 targ->parent_sasaddr = le64toh(parent_sas_address);
902 targ->parent_devinfo = parent_devinfo;
904 targ->linkrate = (linkrate>>4);
907 targ->flags = MPR_TARGET_IS_SATA_SSD;
909 if ((le16toh(config_page.Flags) &
910 MPI25_SAS_DEVICE0_FLAGS_ENABLED_FAST_PATH) &&
911 (le16toh(config_page.Flags) &
912 MPI25_SAS_DEVICE0_FLAGS_FAST_PATH_CAPABLE)) {
913 targ->scsi_req_desc_type =
914 MPI25_REQ_DESCRIPT_FLAGS_FAST_PATH_SCSI_IO;
916 if (le16toh(config_page.Flags) &
917 MPI2_SAS_DEVICE0_FLAGS_ENCL_LEVEL_VALID) {
918 targ->encl_level_valid = TRUE;
920 TAILQ_INIT(&targ->commands);
921 TAILQ_INIT(&targ->timedout_commands);
922 while (!SLIST_EMPTY(&targ->luns)) {
923 lun = SLIST_FIRST(&targ->luns);
924 SLIST_REMOVE_HEAD(&targ->luns, lun_link);
927 SLIST_INIT(&targ->luns);
929 mpr_describe_devinfo(targ->devinfo, devstring, 80);
930 mpr_dprint(sc, (MPR_INFO|MPR_MAPPING), "Found device <%s> <%s> "
931 "handle<0x%04x> enclosureHandle<0x%04x> slot %d\n", devstring,
932 mpr_describe_table(mpr_linkrate_names, targ->linkrate),
933 targ->handle, targ->encl_handle, targ->encl_slot);
934 if (targ->encl_level_valid) {
935 mpr_dprint(sc, (MPR_INFO|MPR_MAPPING), "At enclosure level %d "
936 "and connector name (%4s)\n", targ->encl_level,
937 targ->connector_name);
939 #if ((__FreeBSD_version >= 1000000) && (__FreeBSD_version < 1000039)) || \
940 (__FreeBSD_version < 902502)
941 if ((sassc->flags & MPRSAS_IN_STARTUP) == 0)
943 mprsas_rescan_target(sc, targ);
944 mpr_dprint(sc, MPR_MAPPING, "Target id 0x%x added\n", targ->tid);
947 * Check all commands to see if the SATA_ID_TIMEOUT flag has been set.
948 * If so, send a Target Reset TM to the target that was just created.
949 * An Abort Task TM should be used instead of a Target Reset, but that
950 * would be much more difficult because targets have not been fully
951 * discovered yet, and LUN's haven't been setup. So, just reset the
952 * target instead of the LUN.
954 for (i = 1; i < sc->num_reqs; i++) {
955 cm = &sc->commands[i];
956 if (cm->cm_flags & MPR_CM_FLAGS_SATA_ID_TIMEOUT) {
958 cm->cm_state = MPR_CM_STATE_TIMEDOUT;
960 if ((targ->tm = mprsas_alloc_tm(sc)) != NULL) {
961 mpr_dprint(sc, MPR_INFO, "%s: sending Target "
962 "Reset for stuck SATA identify command "
963 "(cm = %p)\n", __func__, cm);
964 targ->tm->cm_targ = targ;
965 mprsas_send_reset(sc, targ->tm,
966 MPI2_SCSITASKMGMT_TASKTYPE_TARGET_RESET);
968 mpr_dprint(sc, MPR_ERROR, "Failed to allocate "
969 "tm for Target Reset after SATA ID command "
970 "timed out (cm %p)\n", cm);
973 * No need to check for more since the target is
974 * already being reset.
981 * Free the commands that may not have been freed from the SATA ID call
983 for (i = 1; i < sc->num_reqs; i++) {
984 cm = &sc->commands[i];
985 if (cm->cm_flags & MPR_CM_FLAGS_SATA_ID_TIMEOUT) {
986 mpr_free_command(sc, cm);
989 mprsas_startup_decrement(sassc);
994 mprsas_get_sas_address_for_sata_disk(struct mpr_softc *sc,
995 u64 *sas_address, u16 handle, u32 device_info, u8 *is_SATA_SSD)
997 Mpi2SataPassthroughReply_t mpi_reply;
998 int i, rc, try_count;
1000 union _sata_sas_address hash_address;
1001 struct _ata_identify_device_data ata_identify;
1002 u8 buffer[MPT2SAS_MN_LEN + MPT2SAS_SN_LEN];
1006 memset(&ata_identify, 0, sizeof(ata_identify));
1007 memset(&mpi_reply, 0, sizeof(mpi_reply));
1010 rc = mprsas_get_sata_identify(sc, handle, &mpi_reply,
1011 (char *)&ata_identify, sizeof(ata_identify), device_info);
1013 ioc_status = le16toh(mpi_reply.IOCStatus)
1014 & MPI2_IOCSTATUS_MASK;
1015 sas_status = mpi_reply.SASStatus;
1016 switch (ioc_status) {
1017 case MPI2_IOCSTATUS_SUCCESS:
1019 case MPI2_IOCSTATUS_SCSI_PROTOCOL_ERROR:
1020 /* No sense sleeping. this error won't get better */
1023 if (sc->spinup_wait_time > 0) {
1024 mpr_dprint(sc, MPR_INFO, "Sleeping %d seconds "
1025 "after SATA ID error to wait for spinup\n",
1026 sc->spinup_wait_time);
1027 msleep(&sc->msleep_fake_chan, &sc->mpr_mtx, 0,
1028 "mprid", sc->spinup_wait_time * hz);
1031 } while (((rc && (rc != EWOULDBLOCK)) ||
1032 (ioc_status && (ioc_status != MPI2_IOCSTATUS_SCSI_PROTOCOL_ERROR))
1033 || sas_status) && (try_count < 5));
1035 if (rc == 0 && !ioc_status && !sas_status) {
1036 mpr_dprint(sc, MPR_MAPPING, "%s: got SATA identify "
1037 "successfully for handle = 0x%x with try_count = %d\n",
1038 __func__, handle, try_count);
1040 mpr_dprint(sc, MPR_MAPPING, "%s: handle = 0x%x failed\n",
1044 /* Copy & byteswap the 40 byte model number to a buffer */
1045 for (i = 0; i < MPT2SAS_MN_LEN; i += 2) {
1046 buffer[i] = ((u8 *)ata_identify.model_number)[i + 1];
1047 buffer[i + 1] = ((u8 *)ata_identify.model_number)[i];
1049 /* Copy & byteswap the 20 byte serial number to a buffer */
1050 for (i = 0; i < MPT2SAS_SN_LEN; i += 2) {
1051 buffer[MPT2SAS_MN_LEN + i] =
1052 ((u8 *)ata_identify.serial_number)[i + 1];
1053 buffer[MPT2SAS_MN_LEN + i + 1] =
1054 ((u8 *)ata_identify.serial_number)[i];
1056 bufferptr = (u32 *)buffer;
1057 /* There are 60 bytes to hash down to 8. 60 isn't divisible by 8,
1058 * so loop through the first 56 bytes (7*8),
1059 * and then add in the last dword.
1061 hash_address.word.low = 0;
1062 hash_address.word.high = 0;
1063 for (i = 0; (i < ((MPT2SAS_MN_LEN+MPT2SAS_SN_LEN)/8)); i++) {
1064 hash_address.word.low += *bufferptr;
1066 hash_address.word.high += *bufferptr;
1069 /* Add the last dword */
1070 hash_address.word.low += *bufferptr;
1071 /* Make sure the hash doesn't start with 5, because it could clash
1072 * with a SAS address. Change 5 to a D.
1074 if ((hash_address.word.high & 0x000000F0) == (0x00000050))
1075 hash_address.word.high |= 0x00000080;
1076 *sas_address = (u64)hash_address.wwid[0] << 56 |
1077 (u64)hash_address.wwid[1] << 48 | (u64)hash_address.wwid[2] << 40 |
1078 (u64)hash_address.wwid[3] << 32 | (u64)hash_address.wwid[4] << 24 |
1079 (u64)hash_address.wwid[5] << 16 | (u64)hash_address.wwid[6] << 8 |
1080 (u64)hash_address.wwid[7];
1081 if (ata_identify.rotational_speed == 1) {
1089 mprsas_get_sata_identify(struct mpr_softc *sc, u16 handle,
1090 Mpi2SataPassthroughReply_t *mpi_reply, char *id_buffer, int sz, u32 devinfo)
1092 Mpi2SataPassthroughRequest_t *mpi_request;
1093 Mpi2SataPassthroughReply_t *reply;
1094 struct mpr_command *cm;
1098 buffer = malloc( sz, M_MPR, M_NOWAIT | M_ZERO);
1102 if ((cm = mpr_alloc_command(sc)) == NULL) {
1103 free(buffer, M_MPR);
1106 mpi_request = (MPI2_SATA_PASSTHROUGH_REQUEST *)cm->cm_req;
1107 bzero(mpi_request,sizeof(MPI2_SATA_PASSTHROUGH_REQUEST));
1108 mpi_request->Function = MPI2_FUNCTION_SATA_PASSTHROUGH;
1109 mpi_request->VF_ID = 0;
1110 mpi_request->DevHandle = htole16(handle);
1111 mpi_request->PassthroughFlags = (MPI2_SATA_PT_REQ_PT_FLAGS_PIO |
1112 MPI2_SATA_PT_REQ_PT_FLAGS_READ);
1113 mpi_request->DataLength = htole32(sz);
1114 mpi_request->CommandFIS[0] = 0x27;
1115 mpi_request->CommandFIS[1] = 0x80;
1116 mpi_request->CommandFIS[2] = (devinfo &
1117 MPI2_SAS_DEVICE_INFO_ATAPI_DEVICE) ? 0xA1 : 0xEC;
1118 cm->cm_sge = &mpi_request->SGL;
1119 cm->cm_sglsize = sizeof(MPI2_SGE_IO_UNION);
1120 cm->cm_flags = MPR_CM_FLAGS_DATAIN;
1121 cm->cm_desc.Default.RequestFlags = MPI2_REQ_DESCRIPT_FLAGS_DEFAULT_TYPE;
1122 cm->cm_data = buffer;
1123 cm->cm_length = htole32(sz);
1126 * Start a timeout counter specifically for the SATA ID command. This
1127 * is used to fix a problem where the FW does not send a reply sometimes
1128 * when a bad disk is in the topology. So, this is used to timeout the
1129 * command so that processing can continue normally.
1131 mpr_dprint(sc, MPR_XINFO, "%s start timeout counter for SATA ID "
1132 "command\n", __func__);
1133 callout_reset(&cm->cm_callout, MPR_ATA_ID_TIMEOUT * hz,
1134 mprsas_ata_id_timeout, cm);
1135 error = mpr_wait_command(sc, cm, 60, CAN_SLEEP);
1136 mpr_dprint(sc, MPR_XINFO, "%s stop timeout counter for SATA ID "
1137 "command\n", __func__);
1138 callout_stop(&cm->cm_callout);
1140 reply = (Mpi2SataPassthroughReply_t *)cm->cm_reply;
1141 if (error || (reply == NULL)) {
1144 * If the request returns an error then we need to do a diag
1147 printf("%s: request for page completed with error %d",
1152 bcopy(buffer, id_buffer, sz);
1153 bcopy(reply, mpi_reply, sizeof(Mpi2SataPassthroughReply_t));
1154 if ((le16toh(reply->IOCStatus) & MPI2_IOCSTATUS_MASK) !=
1155 MPI2_IOCSTATUS_SUCCESS) {
1156 printf("%s: error reading SATA PASSTHRU; iocstatus = 0x%x\n",
1157 __func__, reply->IOCStatus);
1163 * If the SATA_ID_TIMEOUT flag has been set for this command, don't free
1164 * it. The command will be freed after sending a target reset TM. If
1165 * the command did timeout, use EWOULDBLOCK.
1167 if ((cm->cm_flags & MPR_CM_FLAGS_SATA_ID_TIMEOUT) == 0)
1168 mpr_free_command(sc, cm);
1169 else if (error == 0)
1170 error = EWOULDBLOCK;
1172 free(buffer, M_MPR);
1177 mprsas_ata_id_timeout(void *data)
1179 struct mpr_softc *sc;
1180 struct mpr_command *cm;
1182 cm = (struct mpr_command *)data;
1184 mtx_assert(&sc->mpr_mtx, MA_OWNED);
1186 mpr_dprint(sc, MPR_INFO, "%s checking ATA ID command %p sc %p\n",
1188 if ((callout_pending(&cm->cm_callout)) ||
1189 (!callout_active(&cm->cm_callout))) {
1190 mpr_dprint(sc, MPR_INFO, "%s ATA ID command almost timed out\n",
1194 callout_deactivate(&cm->cm_callout);
1197 * Run the interrupt handler to make sure it's not pending. This
1198 * isn't perfect because the command could have already completed
1199 * and been re-used, though this is unlikely.
1201 mpr_intr_locked(sc);
1202 if (cm->cm_state == MPR_CM_STATE_FREE) {
1203 mpr_dprint(sc, MPR_INFO, "%s ATA ID command almost timed out\n",
1208 mpr_dprint(sc, MPR_INFO, "ATA ID command timeout cm %p\n", cm);
1211 * Send wakeup() to the sleeping thread that issued this ATA ID command.
1212 * wakeup() will cause msleep to return a 0 (not EWOULDBLOCK), and this
1213 * will keep reinit() from being called. This way, an Abort Task TM can
1214 * be issued so that the timed out command can be cleared. The Abort
1215 * Task cannot be sent from here because the driver has not completed
1216 * setting up targets. Instead, the command is flagged so that special
1217 * handling will be used to send the abort.
1219 cm->cm_flags |= MPR_CM_FLAGS_SATA_ID_TIMEOUT;
1224 mprsas_add_pcie_device(struct mpr_softc *sc, u16 handle, u8 linkrate)
1227 struct mprsas_softc *sassc;
1228 struct mprsas_target *targ;
1229 Mpi2ConfigReply_t mpi_reply;
1230 Mpi26PCIeDevicePage0_t config_page;
1231 Mpi26PCIeDevicePage2_t config_page2;
1232 uint64_t pcie_wwid, parent_wwid = 0;
1233 u32 device_info, parent_devinfo = 0;
1236 struct mprsas_lun *lun;
1239 mprsas_startup_increment(sassc);
1240 if ((mpr_config_get_pcie_device_pg0(sc, &mpi_reply, &config_page,
1241 MPI26_PCIE_DEVICE_PGAD_FORM_HANDLE, handle))) {
1242 printf("%s: error reading PCIe device page0\n", __func__);
1247 device_info = le32toh(config_page.DeviceInfo);
1249 if (((device_info & MPI26_PCIE_DEVINFO_PCI_SWITCH) == 0)
1250 && (le16toh(config_page.ParentDevHandle) != 0)) {
1251 Mpi2ConfigReply_t tmp_mpi_reply;
1252 Mpi26PCIeDevicePage0_t parent_config_page;
1254 if ((mpr_config_get_pcie_device_pg0(sc, &tmp_mpi_reply,
1255 &parent_config_page, MPI26_PCIE_DEVICE_PGAD_FORM_HANDLE,
1256 le16toh(config_page.ParentDevHandle)))) {
1257 printf("%s: error reading PCIe device %#x page0\n",
1258 __func__, le16toh(config_page.ParentDevHandle));
1260 parent_wwid = parent_config_page.WWID.High;
1261 parent_wwid = (parent_wwid << 32) |
1262 parent_config_page.WWID.Low;
1263 parent_devinfo = le32toh(parent_config_page.DeviceInfo);
1266 /* TODO Check proper endianness */
1267 pcie_wwid = config_page.WWID.High;
1268 pcie_wwid = (pcie_wwid << 32) | config_page.WWID.Low;
1269 mpr_dprint(sc, MPR_INFO, "PCIe WWID from PCIe device page0 = %jx\n",
1272 if ((mpr_config_get_pcie_device_pg2(sc, &mpi_reply, &config_page2,
1273 MPI26_PCIE_DEVICE_PGAD_FORM_HANDLE, handle))) {
1274 printf("%s: error reading PCIe device page2\n", __func__);
1279 id = mpr_mapping_get_tid(sc, pcie_wwid, handle);
1280 if (id == MPR_MAP_BAD_ID) {
1281 mpr_dprint(sc, MPR_ERROR | MPR_INFO, "failure at %s:%d/%s()! "
1282 "Could not get ID for device with handle 0x%04x\n",
1283 __FILE__, __LINE__, __func__, handle);
1287 mpr_dprint(sc, MPR_MAPPING, "%s: Target ID for added device is %d.\n",
1290 if (mprsas_check_id(sassc, id) != 0) {
1291 device_printf(sc->mpr_dev, "Excluding target id %d\n", id);
1296 mpr_dprint(sc, MPR_MAPPING, "WWID from PCIe device page0 = %jx\n",
1298 targ = &sassc->targets[id];
1299 targ->devinfo = device_info;
1300 targ->encl_handle = le16toh(config_page.EnclosureHandle);
1301 targ->encl_slot = le16toh(config_page.Slot);
1302 targ->encl_level = config_page.EnclosureLevel;
1303 targ->connector_name[0] = ((char *)&config_page.ConnectorName)[0];
1304 targ->connector_name[1] = ((char *)&config_page.ConnectorName)[1];
1305 targ->connector_name[2] = ((char *)&config_page.ConnectorName)[2];
1306 targ->connector_name[3] = ((char *)&config_page.ConnectorName)[3];
1307 targ->is_nvme = device_info & MPI26_PCIE_DEVINFO_NVME;
1308 targ->MDTS = config_page2.MaximumDataTransferSize;
1310 * Assume always TRUE for encl_level_valid because there is no valid
1313 targ->encl_level_valid = TRUE;
1314 targ->handle = handle;
1315 targ->parent_handle = le16toh(config_page.ParentDevHandle);
1316 targ->sasaddr = mpr_to_u64(&config_page.WWID);
1317 targ->parent_sasaddr = le64toh(parent_wwid);
1318 targ->parent_devinfo = parent_devinfo;
1320 targ->linkrate = linkrate;
1322 if ((le16toh(config_page.Flags) &
1323 MPI26_PCIEDEV0_FLAGS_ENABLED_FAST_PATH) &&
1324 (le16toh(config_page.Flags) &
1325 MPI26_PCIEDEV0_FLAGS_FAST_PATH_CAPABLE)) {
1326 targ->scsi_req_desc_type =
1327 MPI25_REQ_DESCRIPT_FLAGS_FAST_PATH_SCSI_IO;
1329 TAILQ_INIT(&targ->commands);
1330 TAILQ_INIT(&targ->timedout_commands);
1331 while (!SLIST_EMPTY(&targ->luns)) {
1332 lun = SLIST_FIRST(&targ->luns);
1333 SLIST_REMOVE_HEAD(&targ->luns, lun_link);
1336 SLIST_INIT(&targ->luns);
1338 mpr_describe_devinfo(targ->devinfo, devstring, 80);
1339 mpr_dprint(sc, (MPR_INFO|MPR_MAPPING), "Found PCIe device <%s> <%s> "
1340 "handle<0x%04x> enclosureHandle<0x%04x> slot %d\n", devstring,
1341 mpr_describe_table(mpr_pcie_linkrate_names, targ->linkrate),
1342 targ->handle, targ->encl_handle, targ->encl_slot);
1343 if (targ->encl_level_valid) {
1344 mpr_dprint(sc, (MPR_INFO|MPR_MAPPING), "At enclosure level %d "
1345 "and connector name (%4s)\n", targ->encl_level,
1346 targ->connector_name);
1348 #if ((__FreeBSD_version >= 1000000) && (__FreeBSD_version < 1000039)) || \
1349 (__FreeBSD_version < 902502)
1350 if ((sassc->flags & MPRSAS_IN_STARTUP) == 0)
1352 mprsas_rescan_target(sc, targ);
1353 mpr_dprint(sc, MPR_MAPPING, "Target id 0x%x added\n", targ->tid);
1356 mprsas_startup_decrement(sassc);
1361 mprsas_volume_add(struct mpr_softc *sc, u16 handle)
1363 struct mprsas_softc *sassc;
1364 struct mprsas_target *targ;
1368 struct mprsas_lun *lun;
1371 mprsas_startup_increment(sassc);
1372 /* wwid is endian safe */
1373 mpr_config_get_volume_wwid(sc, handle, &wwid);
1375 printf("%s: invalid WWID; cannot add volume to mapping table\n",
1381 id = mpr_mapping_get_raid_tid(sc, wwid, handle);
1382 if (id == MPR_MAP_BAD_ID) {
1383 printf("%s: could not get ID for volume with handle 0x%04x and "
1384 "WWID 0x%016llx\n", __func__, handle,
1385 (unsigned long long)wwid);
1390 targ = &sassc->targets[id];
1392 targ->handle = handle;
1393 targ->devname = wwid;
1394 TAILQ_INIT(&targ->commands);
1395 TAILQ_INIT(&targ->timedout_commands);
1396 while (!SLIST_EMPTY(&targ->luns)) {
1397 lun = SLIST_FIRST(&targ->luns);
1398 SLIST_REMOVE_HEAD(&targ->luns, lun_link);
1401 SLIST_INIT(&targ->luns);
1402 #if ((__FreeBSD_version >= 1000000) && (__FreeBSD_version < 1000039)) || \
1403 (__FreeBSD_version < 902502)
1404 if ((sassc->flags & MPRSAS_IN_STARTUP) == 0)
1406 mprsas_rescan_target(sc, targ);
1407 mpr_dprint(sc, MPR_MAPPING, "RAID target id %d added (WWID = 0x%jx)\n",
1410 mprsas_startup_decrement(sassc);
1415 * mprsas_SSU_to_SATA_devices
1416 * @sc: per adapter object
1418 * Looks through the target list and issues a StartStopUnit SCSI command to each
1419 * SATA direct-access device. This helps to ensure that data corruption is
1420 * avoided when the system is being shut down. This must be called after the IR
1421 * System Shutdown RAID Action is sent if in IR mode.
1426 mprsas_SSU_to_SATA_devices(struct mpr_softc *sc)
1428 struct mprsas_softc *sassc = sc->sassc;
1430 path_id_t pathid = cam_sim_path(sassc->sim);
1431 target_id_t targetid;
1432 struct mprsas_target *target;
1434 struct timeval cur_time, start_time;
1439 * For each target, issue a StartStopUnit command to stop the device.
1441 sc->SSU_started = TRUE;
1442 sc->SSU_refcount = 0;
1443 for (targetid = 0; targetid < sc->max_devices; targetid++) {
1444 target = &sassc->targets[targetid];
1445 if (target->handle == 0x0) {
1450 * The stop_at_shutdown flag will be set if this device is
1451 * a SATA direct-access end device.
1453 if (target->stop_at_shutdown) {
1454 ccb = xpt_alloc_ccb_nowait();
1456 mpr_dprint(sc, MPR_FAULT, "Unable to alloc CCB "
1461 if (xpt_create_path(&ccb->ccb_h.path, xpt_periph,
1462 pathid, targetid, CAM_LUN_WILDCARD) !=
1464 mpr_dprint(sc, MPR_ERROR, "Unable to create "
1465 "path to stop unit.\n");
1469 xpt_path_string(ccb->ccb_h.path, path_str,
1472 mpr_dprint(sc, MPR_INFO, "Sending StopUnit: path %s "
1473 "handle %d\n", path_str, target->handle);
1476 * Issue a START STOP UNIT command for the target.
1477 * Increment the SSU counter to be used to count the
1478 * number of required replies.
1480 mpr_dprint(sc, MPR_INFO, "Incrementing SSU count\n");
1482 ccb->ccb_h.target_id =
1483 xpt_path_target_id(ccb->ccb_h.path);
1484 ccb->ccb_h.ppriv_ptr1 = sassc;
1485 scsi_start_stop(&ccb->csio,
1487 mprsas_stop_unit_done,
1501 * Wait until all of the SSU commands have completed or time has
1502 * expired (60 seconds). Pause for 100ms each time through. If any
1503 * command times out, the target will be reset in the SCSI command
1506 getmicrotime(&start_time);
1507 while (sc->SSU_refcount) {
1508 pause("mprwait", hz/10);
1510 getmicrotime(&cur_time);
1511 if ((cur_time.tv_sec - start_time.tv_sec) > 60) {
1512 mpr_dprint(sc, MPR_ERROR, "Time has expired waiting "
1513 "for SSU commands to complete.\n");
1520 mprsas_stop_unit_done(struct cam_periph *periph, union ccb *done_ccb)
1522 struct mprsas_softc *sassc;
1525 if (done_ccb == NULL)
1528 sassc = (struct mprsas_softc *)done_ccb->ccb_h.ppriv_ptr1;
1530 xpt_path_string(done_ccb->ccb_h.path, path_str, sizeof(path_str));
1531 mpr_dprint(sassc->sc, MPR_INFO, "Completing stop unit for %s\n",
1535 * Nothing more to do except free the CCB and path. If the command
1536 * timed out, an abort reset, then target reset will be issued during
1537 * the SCSI Command process.
1539 xpt_free_path(done_ccb->ccb_h.path);
1540 xpt_free_ccb(done_ccb);
1544 * mprsas_ir_shutdown - IR shutdown notification
1545 * @sc: per adapter object
1547 * Sending RAID Action to alert the Integrated RAID subsystem of the IOC that
1548 * the host system is shutting down.
1553 mprsas_ir_shutdown(struct mpr_softc *sc)
1555 u16 volume_mapping_flags;
1556 u16 ioc_pg8_flags = le16toh(sc->ioc_pg8.Flags);
1557 struct dev_mapping_table *mt_entry;
1558 u32 start_idx, end_idx;
1559 unsigned int id, found_volume = 0;
1560 struct mpr_command *cm;
1561 Mpi2RaidActionRequest_t *action;
1562 target_id_t targetid;
1563 struct mprsas_target *target;
1565 mpr_dprint(sc, MPR_TRACE, "%s\n", __func__);
1567 /* is IR firmware build loaded? */
1568 if (!sc->ir_firmware)
1571 /* are there any volumes? Look at IR target IDs. */
1572 // TODO-later, this should be looked up in the RAID config structure
1573 // when it is implemented.
1574 volume_mapping_flags = le16toh(sc->ioc_pg8.IRVolumeMappingFlags) &
1575 MPI2_IOCPAGE8_IRFLAGS_MASK_VOLUME_MAPPING_MODE;
1576 if (volume_mapping_flags == MPI2_IOCPAGE8_IRFLAGS_LOW_VOLUME_MAPPING) {
1578 if (ioc_pg8_flags & MPI2_IOCPAGE8_FLAGS_RESERVED_TARGETID_0)
1581 start_idx = sc->max_devices - sc->max_volumes;
1582 end_idx = start_idx + sc->max_volumes - 1;
1584 for (id = start_idx; id < end_idx; id++) {
1585 mt_entry = &sc->mapping_table[id];
1586 if ((mt_entry->physical_id != 0) &&
1587 (mt_entry->missing_count == 0)) {
1596 if ((cm = mpr_alloc_command(sc)) == NULL) {
1597 printf("%s: command alloc failed\n", __func__);
1601 action = (MPI2_RAID_ACTION_REQUEST *)cm->cm_req;
1602 action->Function = MPI2_FUNCTION_RAID_ACTION;
1603 action->Action = MPI2_RAID_ACTION_SYSTEM_SHUTDOWN_INITIATED;
1604 cm->cm_desc.Default.RequestFlags = MPI2_REQ_DESCRIPT_FLAGS_DEFAULT_TYPE;
1606 mpr_wait_command(sc, cm, 5, CAN_SLEEP);
1610 * Don't check for reply, just leave.
1613 mpr_free_command(sc, cm);
1617 * All of the targets must have the correct value set for
1618 * 'stop_at_shutdown' for the current 'enable_ssu' sysctl variable.
1620 * The possible values for the 'enable_ssu' variable are:
1621 * 0: disable to SSD and HDD
1622 * 1: disable only to HDD (default)
1623 * 2: disable only to SSD
1624 * 3: enable to SSD and HDD
1625 * anything else will default to 1.
1627 for (targetid = 0; targetid < sc->max_devices; targetid++) {
1628 target = &sc->sassc->targets[targetid];
1629 if (target->handle == 0x0) {
1633 if (target->supports_SSU) {
1634 switch (sc->enable_ssu) {
1635 case MPR_SSU_DISABLE_SSD_DISABLE_HDD:
1636 target->stop_at_shutdown = FALSE;
1638 case MPR_SSU_DISABLE_SSD_ENABLE_HDD:
1639 target->stop_at_shutdown = TRUE;
1640 if (target->flags & MPR_TARGET_IS_SATA_SSD) {
1641 target->stop_at_shutdown = FALSE;
1644 case MPR_SSU_ENABLE_SSD_ENABLE_HDD:
1645 target->stop_at_shutdown = TRUE;
1647 case MPR_SSU_ENABLE_SSD_DISABLE_HDD:
1649 target->stop_at_shutdown = TRUE;
1650 if ((target->flags &
1651 MPR_TARGET_IS_SATA_SSD) == 0) {
1652 target->stop_at_shutdown = FALSE;
1658 mprsas_SSU_to_SATA_devices(sc);