2 * SPDX-License-Identifier: BSD-4-Clause
4 * Copyright (c) 1997, 1998, 1999, 2000
5 * Bill Paul <wpaul@ee.columbia.edu>. All rights reserved.
8 * Alfred Perlstein <alfred@FreeBSD.org>. All rights reserved.
10 * Redistribution and use in source and binary forms, with or without
11 * modification, are permitted provided that the following conditions
13 * 1. Redistributions of source code must retain the above copyright
14 * notice, this list of conditions and the following disclaimer.
15 * 2. Redistributions in binary form must reproduce the above copyright
16 * notice, this list of conditions and the following disclaimer in the
17 * documentation and/or other materials provided with the distribution.
18 * 3. All advertising materials mentioning features or use of this software
19 * must display the following acknowledgement:
20 * This product includes software developed by Bill Paul.
21 * 4. Neither the name of the author nor the names of any co-contributors
22 * may be used to endorse or promote products derived from this software
23 * without specific prior written permission.
25 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
26 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
27 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
28 * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
29 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
30 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
31 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
32 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
33 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
34 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
35 * THE POSSIBILITY OF SUCH DAMAGE.
38 #include <sys/cdefs.h>
39 __FBSDID("$FreeBSD$");
42 * ADMtek AN986 Pegasus and AN8511 Pegasus II USB to ethernet driver.
43 * Datasheet is available from http://www.admtek.com.tw.
45 * Written by Bill Paul <wpaul@ee.columbia.edu>
46 * Electrical Engineering Department
47 * Columbia University, New York City
49 * SMP locking by Alfred Perlstein <alfred@FreeBSD.org>.
54 * The Pegasus chip uses four USB "endpoints" to provide 10/100 ethernet
55 * support: the control endpoint for reading/writing registers, burst
56 * read endpoint for packet reception, burst write for packet transmission
57 * and one for "interrupts." The chip uses the same RX filter scheme
58 * as the other ADMtek ethernet parts: one perfect filter entry for the
59 * the station address and a 64-bit multicast hash table. The chip supports
60 * both MII and HomePNA attachments.
62 * Since the maximum data transfer speed of USB is supposed to be 12Mbps,
63 * you're never really going to get 100Mbps speeds from this device. I
64 * think the idea is to allow the device to connect to 10 or 100Mbps
65 * networks, not necessarily to provide 100Mbps performance. Also, since
66 * the controller uses an external PHY chip, it's possible that board
67 * designers might simply choose a 10Mbps PHY.
69 * Registers are accessed using uether_do_request(). Packet
70 * transfers are done using usbd_transfer() and friends.
73 #include <sys/stdint.h>
74 #include <sys/stddef.h>
75 #include <sys/param.h>
76 #include <sys/queue.h>
77 #include <sys/types.h>
78 #include <sys/systm.h>
79 #include <sys/socket.h>
80 #include <sys/kernel.h>
82 #include <sys/module.h>
84 #include <sys/mutex.h>
85 #include <sys/condvar.h>
86 #include <sys/sysctl.h>
88 #include <sys/unistd.h>
89 #include <sys/callout.h>
90 #include <sys/malloc.h>
94 #include <net/if_var.h>
95 #include <net/if_media.h>
97 #include <dev/mii/mii.h>
98 #include <dev/mii/miivar.h>
100 #include <dev/usb/usb.h>
101 #include <dev/usb/usbdi.h>
102 #include <dev/usb/usbdi_util.h>
105 #define USB_DEBUG_VAR aue_debug
106 #include <dev/usb/usb_debug.h>
107 #include <dev/usb/usb_process.h>
109 #include <dev/usb/net/usb_ethernet.h>
110 #include <dev/usb/net/if_auereg.h>
112 #include "miibus_if.h"
115 static int aue_debug = 0;
117 static SYSCTL_NODE(_hw_usb, OID_AUTO, aue, CTLFLAG_RW | CTLFLAG_MPSAFE, 0,
119 SYSCTL_INT(_hw_usb_aue, OID_AUTO, debug, CTLFLAG_RWTUN, &aue_debug, 0,
124 * Various supported device vendors/products.
126 static const STRUCT_USB_HOST_ID aue_devs[] = {
127 #define AUE_DEV(v,p,i) { USB_VPI(USB_VENDOR_##v, USB_PRODUCT_##v##_##p, i) }
128 AUE_DEV(3COM, 3C460B, AUE_FLAG_PII),
129 AUE_DEV(ABOCOM, DSB650TX_PNA, 0),
130 AUE_DEV(ABOCOM, UFE1000, AUE_FLAG_LSYS),
131 AUE_DEV(ABOCOM, XX10, 0),
132 AUE_DEV(ABOCOM, XX1, AUE_FLAG_PNA | AUE_FLAG_PII),
133 AUE_DEV(ABOCOM, XX2, AUE_FLAG_PII),
134 AUE_DEV(ABOCOM, XX4, AUE_FLAG_PNA),
135 AUE_DEV(ABOCOM, XX5, AUE_FLAG_PNA),
136 AUE_DEV(ABOCOM, XX6, AUE_FLAG_PII),
137 AUE_DEV(ABOCOM, XX7, AUE_FLAG_PII),
138 AUE_DEV(ABOCOM, XX8, AUE_FLAG_PII),
139 AUE_DEV(ABOCOM, XX9, AUE_FLAG_PNA),
140 AUE_DEV(ACCTON, SS1001, AUE_FLAG_PII),
141 AUE_DEV(ACCTON, USB320_EC, 0),
142 AUE_DEV(ADMTEK, PEGASUSII_2, AUE_FLAG_PII),
143 AUE_DEV(ADMTEK, PEGASUSII_3, AUE_FLAG_PII),
144 AUE_DEV(ADMTEK, PEGASUSII_4, AUE_FLAG_PII),
145 AUE_DEV(ADMTEK, PEGASUSII, AUE_FLAG_PII),
146 AUE_DEV(ADMTEK, PEGASUS, AUE_FLAG_PNA | AUE_FLAG_DUAL_PHY),
147 AUE_DEV(AEI, FASTETHERNET, AUE_FLAG_PII),
148 AUE_DEV(ALLIEDTELESYN, ATUSB100, AUE_FLAG_PII),
149 AUE_DEV(ATEN, UC110T, AUE_FLAG_PII),
150 AUE_DEV(BELKIN, USB2LAN, AUE_FLAG_PII),
151 AUE_DEV(BILLIONTON, USB100, 0),
152 AUE_DEV(BILLIONTON, USBE100, AUE_FLAG_PII),
153 AUE_DEV(BILLIONTON, USBEL100, 0),
154 AUE_DEV(BILLIONTON, USBLP100, AUE_FLAG_PNA),
155 AUE_DEV(COREGA, FETHER_USB_TXS, AUE_FLAG_PII),
156 AUE_DEV(COREGA, FETHER_USB_TX, 0),
157 AUE_DEV(DLINK, DSB650TX1, AUE_FLAG_LSYS),
158 AUE_DEV(DLINK, DSB650TX2, AUE_FLAG_LSYS | AUE_FLAG_PII),
159 AUE_DEV(DLINK, DSB650TX3, AUE_FLAG_LSYS | AUE_FLAG_PII),
160 AUE_DEV(DLINK, DSB650TX4, AUE_FLAG_LSYS | AUE_FLAG_PII),
161 AUE_DEV(DLINK, DSB650TX_PNA, AUE_FLAG_PNA),
162 AUE_DEV(DLINK, DSB650TX, AUE_FLAG_LSYS),
163 AUE_DEV(DLINK, DSB650, AUE_FLAG_LSYS),
164 AUE_DEV(ELCON, PLAN, AUE_FLAG_PNA | AUE_FLAG_PII),
165 AUE_DEV(ELECOM, LDUSB20, AUE_FLAG_PII),
166 AUE_DEV(ELECOM, LDUSBLTX, AUE_FLAG_PII),
167 AUE_DEV(ELECOM, LDUSBTX0, 0),
168 AUE_DEV(ELECOM, LDUSBTX1, AUE_FLAG_LSYS),
169 AUE_DEV(ELECOM, LDUSBTX2, 0),
170 AUE_DEV(ELECOM, LDUSBTX3, AUE_FLAG_LSYS),
171 AUE_DEV(ELSA, USB2ETHERNET, 0),
172 AUE_DEV(GIGABYTE, GNBR402W, 0),
173 AUE_DEV(HAWKING, UF100, AUE_FLAG_PII),
174 AUE_DEV(HP, HN210E, AUE_FLAG_PII),
175 AUE_DEV(IODATA, USBETTXS, AUE_FLAG_PII),
176 AUE_DEV(IODATA, USBETTX, 0),
177 AUE_DEV(KINGSTON, KNU101TX, 0),
178 AUE_DEV(LINKSYS, USB100H1, AUE_FLAG_LSYS | AUE_FLAG_PNA),
179 AUE_DEV(LINKSYS, USB100TX, AUE_FLAG_LSYS),
180 AUE_DEV(LINKSYS, USB10TA, AUE_FLAG_LSYS),
181 AUE_DEV(LINKSYS, USB10TX1, AUE_FLAG_LSYS | AUE_FLAG_PII),
182 AUE_DEV(LINKSYS, USB10TX2, AUE_FLAG_LSYS | AUE_FLAG_PII),
183 AUE_DEV(LINKSYS, USB10T, AUE_FLAG_LSYS),
184 AUE_DEV(MELCO, LUA2TX5, AUE_FLAG_PII),
185 AUE_DEV(MELCO, LUATX1, 0),
186 AUE_DEV(MELCO, LUATX5, 0),
187 AUE_DEV(MICROSOFT, MN110, AUE_FLAG_PII),
188 AUE_DEV(NETGEAR, FA101, AUE_FLAG_PII),
189 AUE_DEV(SIEMENS, SPEEDSTREAM, AUE_FLAG_PII),
190 AUE_DEV(SIIG2, USBTOETHER, AUE_FLAG_PII),
191 AUE_DEV(SMARTBRIDGES, SMARTNIC, AUE_FLAG_PII),
192 AUE_DEV(SMC, 2202USB, 0),
193 AUE_DEV(SMC, 2206USB, AUE_FLAG_PII),
194 AUE_DEV(SOHOWARE, NUB100, 0),
195 AUE_DEV(SOHOWARE, NUB110, AUE_FLAG_PII),
201 static device_probe_t aue_probe;
202 static device_attach_t aue_attach;
203 static device_detach_t aue_detach;
204 static miibus_readreg_t aue_miibus_readreg;
205 static miibus_writereg_t aue_miibus_writereg;
206 static miibus_statchg_t aue_miibus_statchg;
208 static usb_callback_t aue_intr_callback;
209 static usb_callback_t aue_bulk_read_callback;
210 static usb_callback_t aue_bulk_write_callback;
212 static uether_fn_t aue_attach_post;
213 static uether_fn_t aue_init;
214 static uether_fn_t aue_stop;
215 static uether_fn_t aue_start;
216 static uether_fn_t aue_tick;
217 static uether_fn_t aue_setmulti;
218 static uether_fn_t aue_setpromisc;
220 static uint8_t aue_csr_read_1(struct aue_softc *, uint16_t);
221 static uint16_t aue_csr_read_2(struct aue_softc *, uint16_t);
222 static void aue_csr_write_1(struct aue_softc *, uint16_t, uint8_t);
223 static void aue_csr_write_2(struct aue_softc *, uint16_t, uint16_t);
224 static uint16_t aue_eeprom_getword(struct aue_softc *, int);
225 static void aue_reset(struct aue_softc *);
226 static void aue_reset_pegasus_II(struct aue_softc *);
228 static int aue_ifmedia_upd(struct ifnet *);
229 static void aue_ifmedia_sts(struct ifnet *, struct ifmediareq *);
231 static const struct usb_config aue_config[AUE_N_TRANSFER] = {
235 .endpoint = UE_ADDR_ANY,
236 .direction = UE_DIR_OUT,
237 .bufsize = (MCLBYTES + 2),
238 .flags = {.pipe_bof = 1,.force_short_xfer = 1,},
239 .callback = aue_bulk_write_callback,
240 .timeout = 10000, /* 10 seconds */
245 .endpoint = UE_ADDR_ANY,
246 .direction = UE_DIR_IN,
247 .bufsize = (MCLBYTES + 4 + ETHER_CRC_LEN),
248 .flags = {.pipe_bof = 1,.short_xfer_ok = 1,},
249 .callback = aue_bulk_read_callback,
253 .type = UE_INTERRUPT,
254 .endpoint = UE_ADDR_ANY,
255 .direction = UE_DIR_IN,
256 .flags = {.pipe_bof = 1,.short_xfer_ok = 1,},
257 .bufsize = 0, /* use wMaxPacketSize */
258 .callback = aue_intr_callback,
262 static device_method_t aue_methods[] = {
263 /* Device interface */
264 DEVMETHOD(device_probe, aue_probe),
265 DEVMETHOD(device_attach, aue_attach),
266 DEVMETHOD(device_detach, aue_detach),
269 DEVMETHOD(miibus_readreg, aue_miibus_readreg),
270 DEVMETHOD(miibus_writereg, aue_miibus_writereg),
271 DEVMETHOD(miibus_statchg, aue_miibus_statchg),
276 static driver_t aue_driver = {
278 .methods = aue_methods,
279 .size = sizeof(struct aue_softc)
282 static devclass_t aue_devclass;
284 DRIVER_MODULE(aue, uhub, aue_driver, aue_devclass, NULL, 0);
285 DRIVER_MODULE(miibus, aue, miibus_driver, miibus_devclass, 0, 0);
286 MODULE_DEPEND(aue, uether, 1, 1, 1);
287 MODULE_DEPEND(aue, usb, 1, 1, 1);
288 MODULE_DEPEND(aue, ether, 1, 1, 1);
289 MODULE_DEPEND(aue, miibus, 1, 1, 1);
290 MODULE_VERSION(aue, 1);
291 USB_PNP_HOST_INFO(aue_devs);
293 static const struct usb_ether_methods aue_ue_methods = {
294 .ue_attach_post = aue_attach_post,
295 .ue_start = aue_start,
299 .ue_setmulti = aue_setmulti,
300 .ue_setpromisc = aue_setpromisc,
301 .ue_mii_upd = aue_ifmedia_upd,
302 .ue_mii_sts = aue_ifmedia_sts,
305 #define AUE_SETBIT(sc, reg, x) \
306 aue_csr_write_1(sc, reg, aue_csr_read_1(sc, reg) | (x))
308 #define AUE_CLRBIT(sc, reg, x) \
309 aue_csr_write_1(sc, reg, aue_csr_read_1(sc, reg) & ~(x))
312 aue_csr_read_1(struct aue_softc *sc, uint16_t reg)
314 struct usb_device_request req;
318 req.bmRequestType = UT_READ_VENDOR_DEVICE;
319 req.bRequest = AUE_UR_READREG;
320 USETW(req.wValue, 0);
321 USETW(req.wIndex, reg);
322 USETW(req.wLength, 1);
324 err = uether_do_request(&sc->sc_ue, &req, &val, 1000);
331 aue_csr_read_2(struct aue_softc *sc, uint16_t reg)
333 struct usb_device_request req;
337 req.bmRequestType = UT_READ_VENDOR_DEVICE;
338 req.bRequest = AUE_UR_READREG;
339 USETW(req.wValue, 0);
340 USETW(req.wIndex, reg);
341 USETW(req.wLength, 2);
343 err = uether_do_request(&sc->sc_ue, &req, &val, 1000);
346 return (le16toh(val));
350 aue_csr_write_1(struct aue_softc *sc, uint16_t reg, uint8_t val)
352 struct usb_device_request req;
354 req.bmRequestType = UT_WRITE_VENDOR_DEVICE;
355 req.bRequest = AUE_UR_WRITEREG;
358 USETW(req.wIndex, reg);
359 USETW(req.wLength, 1);
361 if (uether_do_request(&sc->sc_ue, &req, &val, 1000)) {
367 aue_csr_write_2(struct aue_softc *sc, uint16_t reg, uint16_t val)
369 struct usb_device_request req;
371 req.bmRequestType = UT_WRITE_VENDOR_DEVICE;
372 req.bRequest = AUE_UR_WRITEREG;
373 USETW(req.wValue, val);
374 USETW(req.wIndex, reg);
375 USETW(req.wLength, 2);
379 if (uether_do_request(&sc->sc_ue, &req, &val, 1000)) {
385 * Read a word of data stored in the EEPROM at address 'addr.'
388 aue_eeprom_getword(struct aue_softc *sc, int addr)
392 aue_csr_write_1(sc, AUE_EE_REG, addr);
393 aue_csr_write_1(sc, AUE_EE_CTL, AUE_EECTL_READ);
395 for (i = 0; i != AUE_TIMEOUT; i++) {
396 if (aue_csr_read_1(sc, AUE_EE_CTL) & AUE_EECTL_DONE)
398 if (uether_pause(&sc->sc_ue, hz / 100))
402 if (i == AUE_TIMEOUT)
403 device_printf(sc->sc_ue.ue_dev, "EEPROM read timed out\n");
405 return (aue_csr_read_2(sc, AUE_EE_DATA));
409 * Read station address(offset 0) from the EEPROM.
412 aue_read_mac(struct aue_softc *sc, uint8_t *eaddr)
417 for (i = 0, offset = 0; i < ETHER_ADDR_LEN / 2; i++) {
418 word = aue_eeprom_getword(sc, offset + i);
419 eaddr[i * 2] = (uint8_t)word;
420 eaddr[i * 2 + 1] = (uint8_t)(word >> 8);
425 aue_miibus_readreg(device_t dev, int phy, int reg)
427 struct aue_softc *sc = device_get_softc(dev);
431 locked = mtx_owned(&sc->sc_mtx);
436 * The Am79C901 HomePNA PHY actually contains two transceivers: a 1Mbps
437 * HomePNA PHY and a 10Mbps full/half duplex ethernet PHY with NWAY
438 * autoneg. However in the ADMtek adapter, only the 1Mbps PHY is
439 * actually connected to anything, so we ignore the 10Mbps one. It
440 * happens to be configured for MII address 3, so we filter that out.
442 if (sc->sc_flags & AUE_FLAG_DUAL_PHY) {
450 aue_csr_write_1(sc, AUE_PHY_ADDR, phy);
451 aue_csr_write_1(sc, AUE_PHY_CTL, reg | AUE_PHYCTL_READ);
453 for (i = 0; i != AUE_TIMEOUT; i++) {
454 if (aue_csr_read_1(sc, AUE_PHY_CTL) & AUE_PHYCTL_DONE)
456 if (uether_pause(&sc->sc_ue, hz / 100))
460 if (i == AUE_TIMEOUT)
461 device_printf(sc->sc_ue.ue_dev, "MII read timed out\n");
463 val = aue_csr_read_2(sc, AUE_PHY_DATA);
472 aue_miibus_writereg(device_t dev, int phy, int reg, int data)
474 struct aue_softc *sc = device_get_softc(dev);
481 locked = mtx_owned(&sc->sc_mtx);
485 aue_csr_write_2(sc, AUE_PHY_DATA, data);
486 aue_csr_write_1(sc, AUE_PHY_ADDR, phy);
487 aue_csr_write_1(sc, AUE_PHY_CTL, reg | AUE_PHYCTL_WRITE);
489 for (i = 0; i != AUE_TIMEOUT; i++) {
490 if (aue_csr_read_1(sc, AUE_PHY_CTL) & AUE_PHYCTL_DONE)
492 if (uether_pause(&sc->sc_ue, hz / 100))
496 if (i == AUE_TIMEOUT)
497 device_printf(sc->sc_ue.ue_dev, "MII write timed out\n");
505 aue_miibus_statchg(device_t dev)
507 struct aue_softc *sc = device_get_softc(dev);
508 struct mii_data *mii = GET_MII(sc);
511 locked = mtx_owned(&sc->sc_mtx);
515 AUE_CLRBIT(sc, AUE_CTL0, AUE_CTL0_RX_ENB | AUE_CTL0_TX_ENB);
516 if (IFM_SUBTYPE(mii->mii_media_active) == IFM_100_TX)
517 AUE_SETBIT(sc, AUE_CTL1, AUE_CTL1_SPEEDSEL);
519 AUE_CLRBIT(sc, AUE_CTL1, AUE_CTL1_SPEEDSEL);
521 if ((mii->mii_media_active & IFM_GMASK) == IFM_FDX)
522 AUE_SETBIT(sc, AUE_CTL1, AUE_CTL1_DUPLEX);
524 AUE_CLRBIT(sc, AUE_CTL1, AUE_CTL1_DUPLEX);
526 AUE_SETBIT(sc, AUE_CTL0, AUE_CTL0_RX_ENB | AUE_CTL0_TX_ENB);
529 * Set the LED modes on the LinkSys adapter.
530 * This turns on the 'dual link LED' bin in the auxmode
531 * register of the Broadcom PHY.
533 if (sc->sc_flags & AUE_FLAG_LSYS) {
536 auxmode = aue_miibus_readreg(dev, 0, 0x1b);
537 aue_miibus_writereg(dev, 0, 0x1b, auxmode | 0x04);
545 aue_hash_maddr(void *arg, struct sockaddr_dl *sdl, u_int cnt)
547 uint8_t *hashtbl = arg;
550 h = ether_crc32_le(LLADDR(sdl), ETHER_ADDR_LEN) & ((1 << AUE_BITS) - 1);
551 hashtbl[(h >> 3)] |= 1 << (h & 0x7);
557 aue_setmulti(struct usb_ether *ue)
559 struct aue_softc *sc = uether_getsc(ue);
560 struct ifnet *ifp = uether_getifp(ue);
562 uint8_t hashtbl[8] = { 0, 0, 0, 0, 0, 0, 0, 0 };
564 AUE_LOCK_ASSERT(sc, MA_OWNED);
566 if (ifp->if_flags & IFF_ALLMULTI || ifp->if_flags & IFF_PROMISC) {
567 AUE_SETBIT(sc, AUE_CTL0, AUE_CTL0_ALLMULTI);
571 AUE_CLRBIT(sc, AUE_CTL0, AUE_CTL0_ALLMULTI);
573 /* now program new ones */
574 if_foreach_llmaddr(ifp, aue_hash_maddr, hashtbl);
576 /* write the hashtable */
577 for (i = 0; i != 8; i++)
578 aue_csr_write_1(sc, AUE_MAR0 + i, hashtbl[i]);
582 aue_reset_pegasus_II(struct aue_softc *sc)
584 /* Magic constants taken from Linux driver. */
585 aue_csr_write_1(sc, AUE_REG_1D, 0);
586 aue_csr_write_1(sc, AUE_REG_7B, 2);
588 if ((sc->sc_flags & HAS_HOME_PNA) && mii_mode)
589 aue_csr_write_1(sc, AUE_REG_81, 6);
592 aue_csr_write_1(sc, AUE_REG_81, 2);
596 aue_reset(struct aue_softc *sc)
600 AUE_SETBIT(sc, AUE_CTL1, AUE_CTL1_RESETMAC);
602 for (i = 0; i != AUE_TIMEOUT; i++) {
603 if (!(aue_csr_read_1(sc, AUE_CTL1) & AUE_CTL1_RESETMAC))
605 if (uether_pause(&sc->sc_ue, hz / 100))
609 if (i == AUE_TIMEOUT)
610 device_printf(sc->sc_ue.ue_dev, "reset failed\n");
613 * The PHY(s) attached to the Pegasus chip may be held
614 * in reset until we flip on the GPIO outputs. Make sure
615 * to set the GPIO pins high so that the PHY(s) will
618 * NOTE: We used to force all of the GPIO pins low first and then
619 * enable the ones we want. This has been changed to better
620 * match the ADMtek's reference design to avoid setting the
621 * power-down configuration line of the PHY at the same time
624 aue_csr_write_1(sc, AUE_GPIO0, AUE_GPIO_SEL0|AUE_GPIO_SEL1);
625 aue_csr_write_1(sc, AUE_GPIO0, AUE_GPIO_SEL0|AUE_GPIO_SEL1|AUE_GPIO_OUT0);
627 if (sc->sc_flags & AUE_FLAG_LSYS) {
628 /* Grrr. LinkSys has to be different from everyone else. */
629 aue_csr_write_1(sc, AUE_GPIO0, AUE_GPIO_SEL0|AUE_GPIO_SEL1);
630 aue_csr_write_1(sc, AUE_GPIO0,
631 AUE_GPIO_SEL0|AUE_GPIO_SEL1|AUE_GPIO_OUT0);
633 if (sc->sc_flags & AUE_FLAG_PII)
634 aue_reset_pegasus_II(sc);
636 /* Wait a little while for the chip to get its brains in order: */
637 uether_pause(&sc->sc_ue, hz / 100);
641 aue_attach_post(struct usb_ether *ue)
643 struct aue_softc *sc = uether_getsc(ue);
645 /* reset the adapter */
648 /* get station address from the EEPROM */
649 aue_read_mac(sc, ue->ue_eaddr);
653 * Probe for a Pegasus chip.
656 aue_probe(device_t dev)
658 struct usb_attach_arg *uaa = device_get_ivars(dev);
660 if (uaa->usb_mode != USB_MODE_HOST)
662 if (uaa->info.bConfigIndex != AUE_CONFIG_INDEX)
664 if (uaa->info.bIfaceIndex != AUE_IFACE_IDX)
667 * Belkin USB Bluetooth dongles of the F8T012xx1 model series conflict
668 * with older Belkin USB2LAN adapters. Skip if_aue if we detect one of
669 * the devices that look like Bluetooth adapters.
671 if (uaa->info.idVendor == USB_VENDOR_BELKIN &&
672 uaa->info.idProduct == USB_PRODUCT_BELKIN_F8T012 &&
673 uaa->info.bcdDevice == 0x0413)
676 return (usbd_lookup_id_by_uaa(aue_devs, sizeof(aue_devs), uaa));
680 * Attach the interface. Allocate softc structures, do ifmedia
681 * setup and ethernet/BPF attach.
684 aue_attach(device_t dev)
686 struct usb_attach_arg *uaa = device_get_ivars(dev);
687 struct aue_softc *sc = device_get_softc(dev);
688 struct usb_ether *ue = &sc->sc_ue;
692 sc->sc_flags = USB_GET_DRIVER_INFO(uaa);
694 if (uaa->info.bcdDevice >= 0x0201) {
695 /* XXX currently undocumented */
696 sc->sc_flags |= AUE_FLAG_VER_2;
699 device_set_usb_desc(dev);
700 mtx_init(&sc->sc_mtx, device_get_nameunit(dev), NULL, MTX_DEF);
702 iface_index = AUE_IFACE_IDX;
703 error = usbd_transfer_setup(uaa->device, &iface_index,
704 sc->sc_xfer, aue_config, AUE_N_TRANSFER,
707 device_printf(dev, "allocating USB transfers failed\n");
713 ue->ue_udev = uaa->device;
714 ue->ue_mtx = &sc->sc_mtx;
715 ue->ue_methods = &aue_ue_methods;
717 error = uether_ifattach(ue);
719 device_printf(dev, "could not attach interface\n");
722 return (0); /* success */
726 return (ENXIO); /* failure */
730 aue_detach(device_t dev)
732 struct aue_softc *sc = device_get_softc(dev);
733 struct usb_ether *ue = &sc->sc_ue;
735 usbd_transfer_unsetup(sc->sc_xfer, AUE_N_TRANSFER);
737 mtx_destroy(&sc->sc_mtx);
743 aue_intr_callback(struct usb_xfer *xfer, usb_error_t error)
745 struct aue_softc *sc = usbd_xfer_softc(xfer);
746 struct ifnet *ifp = uether_getifp(&sc->sc_ue);
747 struct aue_intrpkt pkt;
748 struct usb_page_cache *pc;
751 usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL);
753 switch (USB_GET_STATE(xfer)) {
754 case USB_ST_TRANSFERRED:
756 if ((ifp->if_drv_flags & IFF_DRV_RUNNING) &&
757 actlen >= (int)sizeof(pkt)) {
759 pc = usbd_xfer_get_frame(xfer, 0);
760 usbd_copy_out(pc, 0, &pkt, sizeof(pkt));
763 if_inc_counter(ifp, IFCOUNTER_OERRORS, 1);
764 if (pkt.aue_txstat0 & (AUE_TXSTAT0_LATECOLL |
765 AUE_TXSTAT0_EXCESSCOLL))
766 if_inc_counter(ifp, IFCOUNTER_COLLISIONS, 1);
771 usbd_xfer_set_frame_len(xfer, 0, usbd_xfer_max_len(xfer));
772 usbd_transfer_submit(xfer);
776 if (error != USB_ERR_CANCELLED) {
777 /* try to clear stall first */
778 usbd_xfer_set_stall(xfer);
786 aue_bulk_read_callback(struct usb_xfer *xfer, usb_error_t error)
788 struct aue_softc *sc = usbd_xfer_softc(xfer);
789 struct usb_ether *ue = &sc->sc_ue;
790 struct ifnet *ifp = uether_getifp(ue);
791 struct aue_rxpkt stat;
792 struct usb_page_cache *pc;
795 usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL);
796 pc = usbd_xfer_get_frame(xfer, 0);
798 switch (USB_GET_STATE(xfer)) {
799 case USB_ST_TRANSFERRED:
800 DPRINTFN(11, "received %d bytes\n", actlen);
802 if (sc->sc_flags & AUE_FLAG_VER_2) {
805 if_inc_counter(ifp, IFCOUNTER_IERRORS, 1);
810 if (actlen <= (int)(sizeof(stat) + ETHER_CRC_LEN)) {
811 if_inc_counter(ifp, IFCOUNTER_IERRORS, 1);
814 usbd_copy_out(pc, actlen - sizeof(stat), &stat,
818 * turn off all the non-error bits in the rx status
821 stat.aue_rxstat &= AUE_RXSTAT_MASK;
822 if (stat.aue_rxstat) {
823 if_inc_counter(ifp, IFCOUNTER_IERRORS, 1);
826 /* No errors; receive the packet. */
827 actlen -= (sizeof(stat) + ETHER_CRC_LEN);
829 uether_rxbuf(ue, pc, 0, actlen);
834 usbd_xfer_set_frame_len(xfer, 0, usbd_xfer_max_len(xfer));
835 usbd_transfer_submit(xfer);
840 DPRINTF("bulk read error, %s\n",
843 if (error != USB_ERR_CANCELLED) {
844 /* try to clear stall first */
845 usbd_xfer_set_stall(xfer);
853 aue_bulk_write_callback(struct usb_xfer *xfer, usb_error_t error)
855 struct aue_softc *sc = usbd_xfer_softc(xfer);
856 struct ifnet *ifp = uether_getifp(&sc->sc_ue);
857 struct usb_page_cache *pc;
862 usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL);
863 pc = usbd_xfer_get_frame(xfer, 0);
865 switch (USB_GET_STATE(xfer)) {
866 case USB_ST_TRANSFERRED:
867 DPRINTFN(11, "transfer of %d bytes complete\n", actlen);
868 if_inc_counter(ifp, IFCOUNTER_OPACKETS, 1);
873 if ((sc->sc_flags & AUE_FLAG_LINK) == 0) {
875 * don't send anything if there is no link !
879 IFQ_DRV_DEQUEUE(&ifp->if_snd, m);
883 if (m->m_pkthdr.len > MCLBYTES)
884 m->m_pkthdr.len = MCLBYTES;
885 if (sc->sc_flags & AUE_FLAG_VER_2) {
887 usbd_xfer_set_frame_len(xfer, 0, m->m_pkthdr.len);
889 usbd_m_copy_in(pc, 0, m, 0, m->m_pkthdr.len);
893 usbd_xfer_set_frame_len(xfer, 0, (m->m_pkthdr.len + 2));
896 * The ADMtek documentation says that the
897 * packet length is supposed to be specified
898 * in the first two bytes of the transfer,
899 * however it actually seems to ignore this
900 * info and base the frame size on the bulk
903 buf[0] = (uint8_t)(m->m_pkthdr.len);
904 buf[1] = (uint8_t)(m->m_pkthdr.len >> 8);
906 usbd_copy_in(pc, 0, buf, 2);
907 usbd_m_copy_in(pc, 2, m, 0, m->m_pkthdr.len);
911 * if there's a BPF listener, bounce a copy
912 * of this frame to him:
918 usbd_transfer_submit(xfer);
922 DPRINTFN(11, "transfer error, %s\n",
925 if_inc_counter(ifp, IFCOUNTER_OERRORS, 1);
927 if (error != USB_ERR_CANCELLED) {
928 /* try to clear stall first */
929 usbd_xfer_set_stall(xfer);
937 aue_tick(struct usb_ether *ue)
939 struct aue_softc *sc = uether_getsc(ue);
940 struct mii_data *mii = GET_MII(sc);
942 AUE_LOCK_ASSERT(sc, MA_OWNED);
945 if ((sc->sc_flags & AUE_FLAG_LINK) == 0
946 && mii->mii_media_status & IFM_ACTIVE &&
947 IFM_SUBTYPE(mii->mii_media_active) != IFM_NONE) {
948 sc->sc_flags |= AUE_FLAG_LINK;
954 aue_start(struct usb_ether *ue)
956 struct aue_softc *sc = uether_getsc(ue);
959 * start the USB transfers, if not already started:
961 usbd_transfer_start(sc->sc_xfer[AUE_INTR_DT_RD]);
962 usbd_transfer_start(sc->sc_xfer[AUE_BULK_DT_RD]);
963 usbd_transfer_start(sc->sc_xfer[AUE_BULK_DT_WR]);
967 aue_init(struct usb_ether *ue)
969 struct aue_softc *sc = uether_getsc(ue);
970 struct ifnet *ifp = uether_getifp(ue);
973 AUE_LOCK_ASSERT(sc, MA_OWNED);
980 /* Set MAC address */
981 for (i = 0; i != ETHER_ADDR_LEN; i++)
982 aue_csr_write_1(sc, AUE_PAR0 + i, IF_LLADDR(ifp)[i]);
984 /* update promiscuous setting */
987 /* Load the multicast filter. */
990 /* Enable RX and TX */
991 aue_csr_write_1(sc, AUE_CTL0, AUE_CTL0_RXSTAT_APPEND | AUE_CTL0_RX_ENB);
992 AUE_SETBIT(sc, AUE_CTL0, AUE_CTL0_TX_ENB);
993 AUE_SETBIT(sc, AUE_CTL2, AUE_CTL2_EP3_CLR);
995 usbd_xfer_set_stall(sc->sc_xfer[AUE_BULK_DT_WR]);
997 ifp->if_drv_flags |= IFF_DRV_RUNNING;
1002 aue_setpromisc(struct usb_ether *ue)
1004 struct aue_softc *sc = uether_getsc(ue);
1005 struct ifnet *ifp = uether_getifp(ue);
1007 AUE_LOCK_ASSERT(sc, MA_OWNED);
1009 /* if we want promiscuous mode, set the allframes bit: */
1010 if (ifp->if_flags & IFF_PROMISC)
1011 AUE_SETBIT(sc, AUE_CTL2, AUE_CTL2_RX_PROMISC);
1013 AUE_CLRBIT(sc, AUE_CTL2, AUE_CTL2_RX_PROMISC);
1017 * Set media options.
1020 aue_ifmedia_upd(struct ifnet *ifp)
1022 struct aue_softc *sc = ifp->if_softc;
1023 struct mii_data *mii = GET_MII(sc);
1024 struct mii_softc *miisc;
1027 AUE_LOCK_ASSERT(sc, MA_OWNED);
1029 sc->sc_flags &= ~AUE_FLAG_LINK;
1030 LIST_FOREACH(miisc, &mii->mii_phys, mii_list)
1032 error = mii_mediachg(mii);
1037 * Report current media status.
1040 aue_ifmedia_sts(struct ifnet *ifp, struct ifmediareq *ifmr)
1042 struct aue_softc *sc = ifp->if_softc;
1043 struct mii_data *mii = GET_MII(sc);
1047 ifmr->ifm_active = mii->mii_media_active;
1048 ifmr->ifm_status = mii->mii_media_status;
1053 * Stop the adapter and free any mbufs allocated to the
1057 aue_stop(struct usb_ether *ue)
1059 struct aue_softc *sc = uether_getsc(ue);
1060 struct ifnet *ifp = uether_getifp(ue);
1062 AUE_LOCK_ASSERT(sc, MA_OWNED);
1064 ifp->if_drv_flags &= ~IFF_DRV_RUNNING;
1065 sc->sc_flags &= ~AUE_FLAG_LINK;
1068 * stop all the transfers, if not already stopped:
1070 usbd_transfer_stop(sc->sc_xfer[AUE_BULK_DT_WR]);
1071 usbd_transfer_stop(sc->sc_xfer[AUE_BULK_DT_RD]);
1072 usbd_transfer_stop(sc->sc_xfer[AUE_INTR_DT_RD]);
1074 aue_csr_write_1(sc, AUE_CTL0, 0);
1075 aue_csr_write_1(sc, AUE_CTL1, 0);