3 * Copyright (c) 2008 Hans Petter Selasky. All rights reserved.
5 * Redistribution and use in source and binary forms, with or without
6 * modification, are permitted provided that the following conditions
8 * 1. Redistributions of source code must retain the above copyright
9 * notice, this list of conditions and the following disclaimer.
10 * 2. Redistributions in binary form must reproduce the above copyright
11 * notice, this list of conditions and the following disclaimer in the
12 * documentation and/or other materials provided with the distribution.
14 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
15 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
16 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
17 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
18 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
19 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
20 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
21 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
22 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
23 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
27 #include <dev/usb/usb_mfunc.h>
28 #include <dev/usb/usb_error.h>
29 #include <dev/usb/usb.h>
31 #define USB_DEBUG_VAR usb2_debug
33 #include <dev/usb/usb_core.h>
34 #include <dev/usb/usb_busdma.h>
35 #include <dev/usb/usb_process.h>
36 #include <dev/usb/usb_transfer.h>
37 #include <dev/usb/usb_device.h>
38 #include <dev/usb/usb_debug.h>
39 #include <dev/usb/usb_util.h>
41 #include <dev/usb/usb_controller.h>
42 #include <dev/usb/usb_bus.h>
44 struct usb2_std_packet_size {
46 uint16_t min; /* inclusive */
47 uint16_t max; /* inclusive */
53 static usb2_callback_t usb2_request_callback;
55 static const struct usb2_config usb2_control_ep_cfg[USB_DEFAULT_XFER_MAX] = {
57 /* This transfer is used for generic control endpoint transfers */
61 .endpoint = 0x00, /* Control endpoint */
62 .direction = UE_DIR_ANY,
63 .bufsize = USB_EP0_BUFSIZE, /* bytes */
64 .flags = {.proxy_buffer = 1,},
65 .callback = &usb2_request_callback,
66 .usb_mode = USB_MODE_MAX, /* both modes */
69 /* This transfer is used for generic clear stall only */
73 .endpoint = 0x00, /* Control pipe */
74 .direction = UE_DIR_ANY,
75 .bufsize = sizeof(struct usb2_device_request),
76 .callback = &usb2_do_clear_stall_callback,
77 .timeout = 1000, /* 1 second */
78 .interval = 50, /* 50ms */
79 .usb_mode = USB_MODE_HOST,
83 /* function prototypes */
85 static void usb2_update_max_frame_size(struct usb2_xfer *);
86 static void usb2_transfer_unsetup_sub(struct usb2_xfer_root *, uint8_t);
87 static void usb2_control_transfer_init(struct usb2_xfer *);
88 static uint8_t usb2_start_hardware_sub(struct usb2_xfer *);
89 static void usb2_callback_proc(struct usb2_proc_msg *);
90 static void usb2_callback_ss_done_defer(struct usb2_xfer *);
91 static void usb2_callback_wrapper(struct usb2_xfer_queue *);
92 static void usb2_dma_delay_done_cb(void *);
93 static void usb2_transfer_start_cb(void *);
94 static uint8_t usb2_callback_wrapper_sub(struct usb2_xfer *);
95 static void usb2_get_std_packet_size(struct usb2_std_packet_size *ptr,
96 uint8_t type, uint8_t usb_speed);
98 /*------------------------------------------------------------------------*
99 * usb2_request_callback
100 *------------------------------------------------------------------------*/
102 usb2_request_callback(struct usb2_xfer *xfer)
104 if (xfer->flags_int.usb2_mode == USB_MODE_DEVICE)
105 usb2_handle_request_callback(xfer);
107 usb2_do_request_callback(xfer);
110 /*------------------------------------------------------------------------*
111 * usb2_update_max_frame_size
113 * This function updates the maximum frame size, hence high speed USB
114 * can transfer multiple consecutive packets.
115 *------------------------------------------------------------------------*/
117 usb2_update_max_frame_size(struct usb2_xfer *xfer)
119 /* compute maximum frame size */
121 if (xfer->max_packet_count == 2) {
122 xfer->max_frame_size = 2 * xfer->max_packet_size;
123 } else if (xfer->max_packet_count == 3) {
124 xfer->max_frame_size = 3 * xfer->max_packet_size;
126 xfer->max_frame_size = xfer->max_packet_size;
130 /*------------------------------------------------------------------------*
133 * The following function is called when we need to
134 * synchronize with DMA hardware.
137 * 0: no DMA delay required
138 * Else: milliseconds of DMA delay
139 *------------------------------------------------------------------------*/
141 usb2_get_dma_delay(struct usb2_bus *bus)
145 if (bus->methods->get_dma_delay) {
146 (bus->methods->get_dma_delay) (bus, &temp);
148 * Round up and convert to milliseconds. Note that we use
149 * 1024 milliseconds per second. to save a division.
157 /*------------------------------------------------------------------------*
158 * usb2_transfer_setup_sub_malloc
160 * This function will allocate one or more DMA'able memory chunks
161 * according to "size", "align" and "count" arguments. "ppc" is
162 * pointed to a linear array of USB page caches afterwards.
167 *------------------------------------------------------------------------*/
170 usb2_transfer_setup_sub_malloc(struct usb2_setup_params *parm,
171 struct usb2_page_cache **ppc, usb2_size_t size, usb2_size_t align,
174 struct usb2_page_cache *pc;
175 struct usb2_page *pg;
177 usb2_size_t n_dma_pc;
184 USB_ASSERT(align > 1, ("Invalid alignment, 0x%08x!\n",
186 USB_ASSERT(size > 0, ("Invalid size = 0!\n"));
189 return (0); /* nothing to allocate */
192 * Make sure that the size is aligned properly.
194 size = -((-size) & (-align));
197 * Try multi-allocation chunks to reduce the number of DMA
198 * allocations, hence DMA allocations are slow.
200 if (size >= PAGE_SIZE) {
204 /* compute number of objects per page */
205 n_obj = (PAGE_SIZE / size);
207 * Compute number of DMA chunks, rounded up
210 n_dma_pc = ((count + n_obj - 1) / n_obj);
213 if (parm->buf == NULL) {
215 parm->dma_page_ptr += n_dma_pc;
216 parm->dma_page_cache_ptr += n_dma_pc;
217 parm->dma_page_ptr += count;
218 parm->xfer_page_cache_ptr += count;
221 for (x = 0; x != n_dma_pc; x++) {
222 /* need to initialize the page cache */
223 parm->dma_page_cache_ptr[x].tag_parent =
224 &parm->curr_xfer->xroot->dma_parent_tag;
226 for (x = 0; x != count; x++) {
227 /* need to initialize the page cache */
228 parm->xfer_page_cache_ptr[x].tag_parent =
229 &parm->curr_xfer->xroot->dma_parent_tag;
233 *ppc = parm->xfer_page_cache_ptr;
235 r = count; /* set remainder count */
236 z = n_obj * size; /* set allocation size */
237 pc = parm->xfer_page_cache_ptr;
238 pg = parm->dma_page_ptr;
240 for (x = 0; x != n_dma_pc; x++) {
243 /* compute last remainder */
247 if (usb2_pc_alloc_mem(parm->dma_page_cache_ptr,
249 return (1); /* failure */
251 /* Set beginning of current buffer */
252 buf = parm->dma_page_cache_ptr->buffer;
253 /* Make room for one DMA page cache and one page */
254 parm->dma_page_cache_ptr++;
257 for (y = 0; (y != n_obj); y++, r--, pc++, pg++) {
259 /* Load sub-chunk into DMA */
260 if (usb2_pc_dmamap_create(pc, size)) {
261 return (1); /* failure */
263 pc->buffer = USB_ADD_BYTES(buf, y * size);
266 mtx_lock(pc->tag_parent->mtx);
267 if (usb2_pc_load_mem(pc, size, 1 /* synchronous */ )) {
268 mtx_unlock(pc->tag_parent->mtx);
269 return (1); /* failure */
271 mtx_unlock(pc->tag_parent->mtx);
275 parm->xfer_page_cache_ptr = pc;
276 parm->dma_page_ptr = pg;
281 /*------------------------------------------------------------------------*
282 * usb2_transfer_setup_sub - transfer setup subroutine
284 * This function must be called from the "xfer_setup" callback of the
285 * USB Host or Device controller driver when setting up an USB
286 * transfer. This function will setup correct packet sizes, buffer
287 * sizes, flags and more, that are stored in the "usb2_xfer"
289 *------------------------------------------------------------------------*/
291 usb2_transfer_setup_sub(struct usb2_setup_params *parm)
297 struct usb2_xfer *xfer = parm->curr_xfer;
298 const struct usb2_config *setup = parm->curr_setup;
299 struct usb2_endpoint_descriptor *edesc;
300 struct usb2_std_packet_size std_size;
301 usb2_frcount_t n_frlengths;
302 usb2_frcount_t n_frbuffers;
308 * Sanity check. The following parameters must be initialized before
309 * calling this function.
311 if ((parm->hc_max_packet_size == 0) ||
312 (parm->hc_max_packet_count == 0) ||
313 (parm->hc_max_frame_size == 0)) {
314 parm->err = USB_ERR_INVAL;
317 edesc = xfer->pipe->edesc;
319 type = (edesc->bmAttributes & UE_XFERTYPE);
321 xfer->flags = setup->flags;
322 xfer->nframes = setup->frames;
323 xfer->timeout = setup->timeout;
324 xfer->callback = setup->callback;
325 xfer->interval = setup->interval;
326 xfer->endpoint = edesc->bEndpointAddress;
327 xfer->max_packet_size = UGETW(edesc->wMaxPacketSize);
328 xfer->max_packet_count = 1;
329 /* make a shadow copy: */
330 xfer->flags_int.usb2_mode = parm->udev->flags.usb2_mode;
332 parm->bufsize = setup->bufsize;
334 if (parm->speed == USB_SPEED_HIGH) {
335 xfer->max_packet_count += (xfer->max_packet_size >> 11) & 3;
336 xfer->max_packet_size &= 0x7FF;
338 /* range check "max_packet_count" */
340 if (xfer->max_packet_count > parm->hc_max_packet_count) {
341 xfer->max_packet_count = parm->hc_max_packet_count;
343 /* filter "wMaxPacketSize" according to HC capabilities */
345 if ((xfer->max_packet_size > parm->hc_max_packet_size) ||
346 (xfer->max_packet_size == 0)) {
347 xfer->max_packet_size = parm->hc_max_packet_size;
349 /* filter "wMaxPacketSize" according to standard sizes */
351 usb2_get_std_packet_size(&std_size, type, parm->speed);
353 if (std_size.range.min || std_size.range.max) {
355 if (xfer->max_packet_size < std_size.range.min) {
356 xfer->max_packet_size = std_size.range.min;
358 if (xfer->max_packet_size > std_size.range.max) {
359 xfer->max_packet_size = std_size.range.max;
363 if (xfer->max_packet_size >= std_size.fixed[3]) {
364 xfer->max_packet_size = std_size.fixed[3];
365 } else if (xfer->max_packet_size >= std_size.fixed[2]) {
366 xfer->max_packet_size = std_size.fixed[2];
367 } else if (xfer->max_packet_size >= std_size.fixed[1]) {
368 xfer->max_packet_size = std_size.fixed[1];
370 /* only one possibility left */
371 xfer->max_packet_size = std_size.fixed[0];
375 /* compute "max_frame_size" */
377 usb2_update_max_frame_size(xfer);
379 /* check interrupt interval and transfer pre-delay */
381 if (type == UE_ISOCHRONOUS) {
383 uint16_t frame_limit;
385 xfer->interval = 0; /* not used, must be zero */
386 xfer->flags_int.isochronous_xfr = 1; /* set flag */
388 if (xfer->timeout == 0) {
390 * set a default timeout in
391 * case something goes wrong!
393 xfer->timeout = 1000 / 4;
395 switch (parm->speed) {
398 frame_limit = USB_MAX_FS_ISOC_FRAMES_PER_XFER;
401 frame_limit = USB_MAX_HS_ISOC_FRAMES_PER_XFER;
405 if (xfer->nframes > frame_limit) {
407 * this is not going to work
410 parm->err = USB_ERR_INVAL;
413 if (xfer->nframes == 0) {
415 * this is not a valid value
417 parm->err = USB_ERR_ZERO_NFRAMES;
423 * if a value is specified use that else check the endpoint
426 if (xfer->interval == 0) {
428 if (type == UE_INTERRUPT) {
430 xfer->interval = edesc->bInterval;
432 switch (parm->speed) {
433 case USB_SPEED_SUPER:
434 case USB_SPEED_VARIABLE:
436 if (xfer->interval < 4)
438 else if (xfer->interval > 16)
439 xfer->interval = (1<<(16-4));
442 (1 << (xfer->interval-4));
451 if (xfer->interval == 0) {
453 * One millisecond is the smallest
454 * interval we support:
463 * NOTE: we do not allow "max_packet_size" or "max_frame_size"
464 * to be equal to zero when setting up USB transfers, hence
465 * this leads to alot of extra code in the USB kernel.
468 if ((xfer->max_frame_size == 0) ||
469 (xfer->max_packet_size == 0)) {
473 if ((parm->bufsize <= MIN_PKT) &&
474 (type != UE_CONTROL) &&
478 xfer->max_packet_size = MIN_PKT;
479 xfer->max_packet_count = 1;
480 parm->bufsize = 0; /* automatic setup length */
481 usb2_update_max_frame_size(xfer);
484 parm->err = USB_ERR_ZERO_MAXP;
493 * check if we should setup a default
497 if (parm->bufsize == 0) {
499 parm->bufsize = xfer->max_frame_size;
501 if (type == UE_ISOCHRONOUS) {
502 parm->bufsize *= xfer->nframes;
506 * check if we are about to setup a proxy
510 if (xfer->flags.proxy_buffer) {
512 /* round bufsize up */
514 parm->bufsize += (xfer->max_frame_size - 1);
516 if (parm->bufsize < xfer->max_frame_size) {
517 /* length wrapped around */
518 parm->err = USB_ERR_INVAL;
521 /* subtract remainder */
523 parm->bufsize -= (parm->bufsize % xfer->max_frame_size);
525 /* add length of USB device request structure, if any */
527 if (type == UE_CONTROL) {
528 parm->bufsize += REQ_SIZE; /* SETUP message */
531 xfer->max_data_length = parm->bufsize;
533 /* Setup "n_frlengths" and "n_frbuffers" */
535 if (type == UE_ISOCHRONOUS) {
536 n_frlengths = xfer->nframes;
540 if (type == UE_CONTROL) {
541 xfer->flags_int.control_xfr = 1;
542 if (xfer->nframes == 0) {
543 if (parm->bufsize <= REQ_SIZE) {
545 * there will never be any data
554 if (xfer->nframes == 0) {
559 n_frlengths = xfer->nframes;
560 n_frbuffers = xfer->nframes;
564 * check if we have room for the
565 * USB device request structure:
568 if (type == UE_CONTROL) {
570 if (xfer->max_data_length < REQ_SIZE) {
571 /* length wrapped around or too small bufsize */
572 parm->err = USB_ERR_INVAL;
575 xfer->max_data_length -= REQ_SIZE;
577 /* setup "frlengths" */
579 xfer->frlengths = parm->xfer_length_ptr;
581 parm->xfer_length_ptr += n_frlengths;
583 /* setup "frbuffers" */
585 xfer->frbuffers = parm->xfer_page_cache_ptr;
587 parm->xfer_page_cache_ptr += n_frbuffers;
590 * check if we need to setup
594 if (!xfer->flags.ext_buffer) {
597 parm->size[0] += ((-parm->size[0]) & (USB_HOST_ALIGN - 1));
602 USB_ADD_BYTES(parm->buf, parm->size[0]);
604 usb2_set_frame_offset(xfer, 0, 0);
606 if ((type == UE_CONTROL) && (n_frbuffers > 1)) {
607 usb2_set_frame_offset(xfer, REQ_SIZE, 1);
610 parm->size[0] += parm->bufsize;
612 /* align data again */
613 parm->size[0] += ((-parm->size[0]) & (USB_HOST_ALIGN - 1));
616 * Compute maximum buffer size
619 if (parm->bufsize_max < parm->bufsize) {
620 parm->bufsize_max = parm->bufsize;
623 if (xfer->flags_int.bdma_enable) {
625 * Setup "dma_page_ptr".
627 * Proof for formula below:
629 * Assume there are three USB frames having length "a", "b" and
630 * "c". These USB frames will at maximum need "z"
631 * "usb2_page" structures. "z" is given by:
633 * z = ((a / USB_PAGE_SIZE) + 2) + ((b / USB_PAGE_SIZE) + 2) +
634 * ((c / USB_PAGE_SIZE) + 2);
636 * Constraining "a", "b" and "c" like this:
638 * (a + b + c) <= parm->bufsize
642 * z <= ((parm->bufsize / USB_PAGE_SIZE) + (3*2));
644 * Here is the general formula:
646 xfer->dma_page_ptr = parm->dma_page_ptr;
647 parm->dma_page_ptr += (2 * n_frbuffers);
648 parm->dma_page_ptr += (parm->bufsize / USB_PAGE_SIZE);
652 /* correct maximum data length */
653 xfer->max_data_length = 0;
655 /* subtract USB frame remainder from "hc_max_frame_size" */
657 xfer->max_hc_frame_size =
658 (parm->hc_max_frame_size -
659 (parm->hc_max_frame_size % xfer->max_frame_size));
661 if (xfer->max_hc_frame_size == 0) {
662 parm->err = USB_ERR_INVAL;
665 /* initialize max frame count */
667 xfer->max_frame_count = xfer->nframes;
669 /* initialize frame buffers */
672 for (x = 0; x != n_frbuffers; x++) {
673 xfer->frbuffers[x].tag_parent =
674 &xfer->xroot->dma_parent_tag;
676 if (xfer->flags_int.bdma_enable &&
677 (parm->bufsize_max > 0)) {
679 if (usb2_pc_dmamap_create(
681 parm->bufsize_max)) {
682 parm->err = USB_ERR_NOMEM;
692 * Set some dummy values so that we avoid division by zero:
694 xfer->max_hc_frame_size = 1;
695 xfer->max_frame_size = 1;
696 xfer->max_packet_size = 1;
697 xfer->max_data_length = 0;
699 xfer->max_frame_count = 0;
703 /*------------------------------------------------------------------------*
704 * usb2_transfer_setup - setup an array of USB transfers
706 * NOTE: You must always call "usb2_transfer_unsetup" after calling
707 * "usb2_transfer_setup" if success was returned.
709 * The idea is that the USB device driver should pre-allocate all its
710 * transfers by one call to this function.
715 *------------------------------------------------------------------------*/
717 usb2_transfer_setup(struct usb2_device *udev,
718 const uint8_t *ifaces, struct usb2_xfer **ppxfer,
719 const struct usb2_config *setup_start, uint16_t n_setup,
720 void *priv_sc, struct mtx *xfer_mtx)
722 struct usb2_xfer dummy;
723 struct usb2_setup_params parm;
724 const struct usb2_config *setup_end = setup_start + n_setup;
725 const struct usb2_config *setup;
726 struct usb2_pipe *pipe;
727 struct usb2_xfer_root *info;
728 struct usb2_xfer *xfer;
737 WITNESS_WARN(WARN_GIANTOK | WARN_SLEEPOK, NULL,
738 "usb2_transfer_setup can sleep!");
740 /* do some checking first */
743 DPRINTFN(6, "setup array has zero length!\n");
744 return (USB_ERR_INVAL);
747 DPRINTFN(6, "ifaces array is NULL!\n");
748 return (USB_ERR_INVAL);
750 if (xfer_mtx == NULL) {
751 DPRINTFN(6, "using global lock\n");
755 for (setup = setup_start, n = 0;
756 setup != setup_end; setup++, n++) {
757 if (setup->bufsize == (usb2_frlength_t)-1) {
758 parm.err = USB_ERR_BAD_BUFSIZE;
759 DPRINTF("invalid bufsize\n");
761 if (setup->callback == NULL) {
762 parm.err = USB_ERR_NO_CALLBACK;
763 DPRINTF("no callback\n");
771 bzero(&parm, sizeof(parm));
774 parm.speed = usb2_get_speed(udev);
775 parm.hc_max_packet_count = 1;
777 if (parm.speed >= USB_SPEED_MAX) {
778 parm.err = USB_ERR_INVAL;
781 /* setup all transfers */
787 * Initialize the "usb2_xfer_root" structure,
788 * which is common for all our USB transfers.
790 info = USB_ADD_BYTES(buf, 0);
792 info->memory_base = buf;
793 info->memory_size = parm.size[0];
796 info->dma_page_cache_start = USB_ADD_BYTES(buf, parm.size[4]);
797 info->dma_page_cache_end = USB_ADD_BYTES(buf, parm.size[5]);
799 info->xfer_page_cache_start = USB_ADD_BYTES(buf, parm.size[5]);
800 info->xfer_page_cache_end = USB_ADD_BYTES(buf, parm.size[2]);
802 usb2_cv_init(&info->cv_drain, "WDRAIN");
804 info->xfer_mtx = xfer_mtx;
806 usb2_dma_tag_setup(&info->dma_parent_tag,
807 parm.dma_tag_p, udev->bus->dma_parent_tag[0].tag,
808 xfer_mtx, &usb2_bdma_done_event, 32, parm.dma_tag_max);
811 info->bus = udev->bus;
814 TAILQ_INIT(&info->done_q.head);
815 info->done_q.command = &usb2_callback_wrapper;
817 TAILQ_INIT(&info->dma_q.head);
818 info->dma_q.command = &usb2_bdma_work_loop;
820 info->done_m[0].hdr.pm_callback = &usb2_callback_proc;
821 info->done_m[0].xroot = info;
822 info->done_m[1].hdr.pm_callback = &usb2_callback_proc;
823 info->done_m[1].xroot = info;
825 if (xfer_mtx == &Giant)
827 &udev->bus->giant_callback_proc;
830 &udev->bus->non_giant_callback_proc;
836 parm.size[0] += sizeof(info[0]);
838 for (setup = setup_start, n = 0;
839 setup != setup_end; setup++, n++) {
841 /* skip USB transfers without callbacks: */
842 if (setup->callback == NULL) {
845 /* see if there is a matching endpoint */
846 pipe = usb2_get_pipe(udev,
847 ifaces[setup->if_index], setup);
849 if ((pipe == NULL) || (pipe->methods == NULL)) {
850 if (setup->flags.no_pipe_ok)
852 if ((setup->usb_mode != USB_MODE_MAX) &&
853 (setup->usb_mode != udev->flags.usb2_mode))
855 parm.err = USB_ERR_NO_PIPE;
859 /* align data properly */
860 parm.size[0] += ((-parm.size[0]) & (USB_HOST_ALIGN - 1));
862 /* store current setup pointer */
863 parm.curr_setup = setup;
867 * Common initialization of the
868 * "usb2_xfer" structure.
870 xfer = USB_ADD_BYTES(buf, parm.size[0]);
871 xfer->address = udev->address;
872 xfer->priv_sc = priv_sc;
875 usb2_callout_init_mtx(&xfer->timeout_handle,
876 &udev->bus->bus_mtx, 0);
879 * Setup a dummy xfer, hence we are
880 * writing to the "usb2_xfer"
881 * structure pointed to by "xfer"
882 * before we have allocated any
886 bzero(&dummy, sizeof(dummy));
890 /* set transfer pipe pointer */
893 parm.size[0] += sizeof(xfer[0]);
894 parm.methods = xfer->pipe->methods;
895 parm.curr_xfer = xfer;
898 * Call the Host or Device controller transfer
901 (udev->bus->methods->xfer_setup) (&parm);
903 /* check for error */
909 * Increment the pipe refcount. This
910 * basically prevents setting a new
911 * configuration and alternate setting
912 * when USB transfers are in use on
913 * the given interface. Search the USB
914 * code for "pipe->refcount" if you
915 * want more information.
917 xfer->pipe->refcount++;
920 * Whenever we set ppxfer[] then we
921 * also need to increment the
924 info->setup_refcount++;
927 * Transfer is successfully setup and
934 if (buf || parm.err) {
938 /* no transfers - nothing to do ! */
941 /* align data properly */
942 parm.size[0] += ((-parm.size[0]) & (USB_HOST_ALIGN - 1));
944 /* store offset temporarily */
945 parm.size[1] = parm.size[0];
948 * The number of DMA tags required depends on
949 * the number of endpoints. The current estimate
950 * for maximum number of DMA tags per endpoint
953 parm.dma_tag_max += 2 * MIN(n_setup, USB_EP_MAX);
956 * DMA tags for QH, TD, Data and more.
958 parm.dma_tag_max += 8;
960 parm.dma_tag_p += parm.dma_tag_max;
962 parm.size[0] += ((uint8_t *)parm.dma_tag_p) -
965 /* align data properly */
966 parm.size[0] += ((-parm.size[0]) & (USB_HOST_ALIGN - 1));
968 /* store offset temporarily */
969 parm.size[3] = parm.size[0];
971 parm.size[0] += ((uint8_t *)parm.dma_page_ptr) -
974 /* align data properly */
975 parm.size[0] += ((-parm.size[0]) & (USB_HOST_ALIGN - 1));
977 /* store offset temporarily */
978 parm.size[4] = parm.size[0];
980 parm.size[0] += ((uint8_t *)parm.dma_page_cache_ptr) -
983 /* store end offset temporarily */
984 parm.size[5] = parm.size[0];
986 parm.size[0] += ((uint8_t *)parm.xfer_page_cache_ptr) -
989 /* store end offset temporarily */
991 parm.size[2] = parm.size[0];
993 /* align data properly */
994 parm.size[0] += ((-parm.size[0]) & (USB_HOST_ALIGN - 1));
996 parm.size[6] = parm.size[0];
998 parm.size[0] += ((uint8_t *)parm.xfer_length_ptr) -
1001 /* align data properly */
1002 parm.size[0] += ((-parm.size[0]) & (USB_HOST_ALIGN - 1));
1004 /* allocate zeroed memory */
1005 buf = malloc(parm.size[0], M_USB, M_WAITOK | M_ZERO);
1008 parm.err = USB_ERR_NOMEM;
1009 DPRINTFN(0, "cannot allocate memory block for "
1010 "configuration (%d bytes)\n",
1014 parm.dma_tag_p = USB_ADD_BYTES(buf, parm.size[1]);
1015 parm.dma_page_ptr = USB_ADD_BYTES(buf, parm.size[3]);
1016 parm.dma_page_cache_ptr = USB_ADD_BYTES(buf, parm.size[4]);
1017 parm.xfer_page_cache_ptr = USB_ADD_BYTES(buf, parm.size[5]);
1018 parm.xfer_length_ptr = USB_ADD_BYTES(buf, parm.size[6]);
1023 if (info->setup_refcount == 0) {
1025 * "usb2_transfer_unsetup_sub" will unlock
1026 * the bus mutex before returning !
1028 USB_BUS_LOCK(info->bus);
1030 /* something went wrong */
1031 usb2_transfer_unsetup_sub(info, 0);
1035 usb2_transfer_unsetup(ppxfer, n_setup);
1040 /*------------------------------------------------------------------------*
1041 * usb2_transfer_unsetup_sub - factored out code
1042 *------------------------------------------------------------------------*/
1044 usb2_transfer_unsetup_sub(struct usb2_xfer_root *info, uint8_t needs_delay)
1046 struct usb2_page_cache *pc;
1048 USB_BUS_LOCK_ASSERT(info->bus, MA_OWNED);
1050 /* wait for any outstanding DMA operations */
1053 usb2_timeout_t temp;
1054 temp = usb2_get_dma_delay(info->bus);
1055 usb2_pause_mtx(&info->bus->bus_mtx,
1056 USB_MS_TO_TICKS(temp));
1059 /* make sure that our done messages are not queued anywhere */
1060 usb2_proc_mwait(info->done_p, &info->done_m[0], &info->done_m[1]);
1062 USB_BUS_UNLOCK(info->bus);
1065 /* free DMA'able memory, if any */
1066 pc = info->dma_page_cache_start;
1067 while (pc != info->dma_page_cache_end) {
1068 usb2_pc_free_mem(pc);
1072 /* free DMA maps in all "xfer->frbuffers" */
1073 pc = info->xfer_page_cache_start;
1074 while (pc != info->xfer_page_cache_end) {
1075 usb2_pc_dmamap_destroy(pc);
1079 /* free all DMA tags */
1080 usb2_dma_tag_unsetup(&info->dma_parent_tag);
1083 usb2_cv_destroy(&info->cv_drain);
1086 * free the "memory_base" last, hence the "info" structure is
1087 * contained within the "memory_base"!
1089 free(info->memory_base, M_USB);
1092 /*------------------------------------------------------------------------*
1093 * usb2_transfer_unsetup - unsetup/free an array of USB transfers
1095 * NOTE: All USB transfers in progress will get called back passing
1096 * the error code "USB_ERR_CANCELLED" before this function
1098 *------------------------------------------------------------------------*/
1100 usb2_transfer_unsetup(struct usb2_xfer **pxfer, uint16_t n_setup)
1102 struct usb2_xfer *xfer;
1103 struct usb2_xfer_root *info;
1104 uint8_t needs_delay = 0;
1106 WITNESS_WARN(WARN_GIANTOK | WARN_SLEEPOK, NULL,
1107 "usb2_transfer_unsetup can sleep!");
1110 xfer = pxfer[n_setup];
1117 USB_XFER_LOCK(xfer);
1118 USB_BUS_LOCK(info->bus);
1121 * HINT: when you start/stop a transfer, it might be a
1122 * good idea to directly use the "pxfer[]" structure:
1124 * usb2_transfer_start(sc->pxfer[0]);
1125 * usb2_transfer_stop(sc->pxfer[0]);
1127 * That way, if your code has many parts that will not
1128 * stop running under the same lock, in other words
1129 * "xfer_mtx", the usb2_transfer_start and
1130 * usb2_transfer_stop functions will simply return
1131 * when they detect a NULL pointer argument.
1133 * To avoid any races we clear the "pxfer[]" pointer
1134 * while holding the private mutex of the driver:
1136 pxfer[n_setup] = NULL;
1138 USB_BUS_UNLOCK(info->bus);
1139 USB_XFER_UNLOCK(xfer);
1141 usb2_transfer_drain(xfer);
1144 if (xfer->flags_int.bdma_enable)
1148 * NOTE: default pipe does not have an
1149 * interface, even if pipe->iface_index == 0
1151 xfer->pipe->refcount--;
1153 usb2_callout_drain(&xfer->timeout_handle);
1155 USB_BUS_LOCK(info->bus);
1157 USB_ASSERT(info->setup_refcount != 0, ("Invalid setup "
1158 "reference count!\n"));
1160 info->setup_refcount--;
1162 if (info->setup_refcount == 0) {
1163 usb2_transfer_unsetup_sub(info,
1166 USB_BUS_UNLOCK(info->bus);
1171 /*------------------------------------------------------------------------*
1172 * usb2_control_transfer_init - factored out code
1174 * In USB Device Mode we have to wait for the SETUP packet which
1175 * containst the "struct usb2_device_request" structure, before we can
1176 * transfer any data. In USB Host Mode we already have the SETUP
1177 * packet at the moment the USB transfer is started. This leads us to
1178 * having to setup the USB transfer at two different places in
1179 * time. This function just contains factored out control transfer
1180 * initialisation code, so that we don't duplicate the code.
1181 *------------------------------------------------------------------------*/
1183 usb2_control_transfer_init(struct usb2_xfer *xfer)
1185 struct usb2_device_request req;
1187 /* copy out the USB request header */
1189 usb2_copy_out(xfer->frbuffers, 0, &req, sizeof(req));
1191 /* setup remainder */
1193 xfer->flags_int.control_rem = UGETW(req.wLength);
1195 /* copy direction to endpoint variable */
1197 xfer->endpoint &= ~(UE_DIR_IN | UE_DIR_OUT);
1199 (req.bmRequestType & UT_READ) ? UE_DIR_IN : UE_DIR_OUT;
1202 /*------------------------------------------------------------------------*
1203 * usb2_start_hardware_sub
1205 * This function handles initialisation of control transfers. Control
1206 * transfers are special in that regard that they can both transmit
1212 *------------------------------------------------------------------------*/
1214 usb2_start_hardware_sub(struct usb2_xfer *xfer)
1216 usb2_frlength_t len;
1218 /* Check for control endpoint stall */
1219 if (xfer->flags.stall_pipe) {
1220 /* no longer active */
1221 xfer->flags_int.control_act = 0;
1224 /* Check for invalid number of frames */
1225 if (xfer->nframes > 2) {
1227 * If you need to split a control transfer, you
1228 * have to do one part at a time. Only with
1229 * non-control transfers you can do multiple
1232 DPRINTFN(0, "Too many frames: %u\n",
1233 (unsigned int)xfer->nframes);
1238 * Check if there is a control
1239 * transfer in progress:
1241 if (xfer->flags_int.control_act) {
1243 if (xfer->flags_int.control_hdr) {
1245 /* clear send header flag */
1247 xfer->flags_int.control_hdr = 0;
1249 /* setup control transfer */
1250 if (xfer->flags_int.usb2_mode == USB_MODE_DEVICE) {
1251 usb2_control_transfer_init(xfer);
1254 /* get data length */
1260 /* the size of the SETUP structure is hardcoded ! */
1262 if (xfer->frlengths[0] != sizeof(struct usb2_device_request)) {
1263 DPRINTFN(0, "Wrong framelength %u != %zu\n",
1264 xfer->frlengths[0], sizeof(struct
1265 usb2_device_request));
1268 /* check USB mode */
1269 if (xfer->flags_int.usb2_mode == USB_MODE_DEVICE) {
1271 /* check number of frames */
1272 if (xfer->nframes != 1) {
1274 * We need to receive the setup
1275 * message first so that we know the
1278 DPRINTF("Misconfigured transfer\n");
1282 * Set a dummy "control_rem" value. This
1283 * variable will be overwritten later by a
1284 * call to "usb2_control_transfer_init()" !
1286 xfer->flags_int.control_rem = 0xFFFF;
1289 /* setup "endpoint" and "control_rem" */
1291 usb2_control_transfer_init(xfer);
1294 /* set transfer-header flag */
1296 xfer->flags_int.control_hdr = 1;
1298 /* get data length */
1300 len = (xfer->sumlen - sizeof(struct usb2_device_request));
1303 /* check if there is a length mismatch */
1305 if (len > xfer->flags_int.control_rem) {
1306 DPRINTFN(0, "Length greater than remaining length!\n");
1309 /* check if we are doing a short transfer */
1311 if (xfer->flags.force_short_xfer) {
1312 xfer->flags_int.control_rem = 0;
1314 if ((len != xfer->max_data_length) &&
1315 (len != xfer->flags_int.control_rem) &&
1316 (xfer->nframes != 1)) {
1317 DPRINTFN(0, "Short control transfer without "
1318 "force_short_xfer set!\n");
1321 xfer->flags_int.control_rem -= len;
1324 /* the status part is executed when "control_act" is 0 */
1326 if ((xfer->flags_int.control_rem > 0) ||
1327 (xfer->flags.manual_status)) {
1328 /* don't execute the STATUS stage yet */
1329 xfer->flags_int.control_act = 1;
1332 if ((!xfer->flags_int.control_hdr) &&
1333 (xfer->nframes == 1)) {
1335 * This is not a valid operation!
1337 DPRINTFN(0, "Invalid parameter "
1342 /* time to execute the STATUS stage */
1343 xfer->flags_int.control_act = 0;
1345 return (0); /* success */
1348 return (1); /* failure */
1351 /*------------------------------------------------------------------------*
1352 * usb2_start_hardware - start USB hardware for the given transfer
1354 * This function should only be called from the USB callback.
1355 *------------------------------------------------------------------------*/
1357 usb2_start_hardware(struct usb2_xfer *xfer)
1361 DPRINTF("xfer=%p, pipe=%p, nframes=%d, dir=%s\n",
1362 xfer, xfer->pipe, xfer->nframes, USB_GET_DATA_ISREAD(xfer) ?
1366 if (USB_DEBUG_VAR > 0) {
1367 USB_BUS_LOCK(xfer->xroot->bus);
1369 usb2_dump_pipe(xfer->pipe);
1371 USB_BUS_UNLOCK(xfer->xroot->bus);
1375 USB_XFER_LOCK_ASSERT(xfer, MA_OWNED);
1376 USB_BUS_LOCK_ASSERT(xfer->xroot->bus, MA_NOTOWNED);
1378 /* Only open the USB transfer once! */
1379 if (!xfer->flags_int.open) {
1380 xfer->flags_int.open = 1;
1384 USB_BUS_LOCK(xfer->xroot->bus);
1385 (xfer->pipe->methods->open) (xfer);
1386 USB_BUS_UNLOCK(xfer->xroot->bus);
1388 /* set "transferring" flag */
1389 xfer->flags_int.transferring = 1;
1392 /* increment power reference */
1393 usb2_transfer_power_ref(xfer, 1);
1396 * Check if the transfer is waiting on a queue, most
1397 * frequently the "done_q":
1399 if (xfer->wait_queue) {
1400 USB_BUS_LOCK(xfer->xroot->bus);
1401 usb2_transfer_dequeue(xfer);
1402 USB_BUS_UNLOCK(xfer->xroot->bus);
1404 /* clear "did_dma_delay" flag */
1405 xfer->flags_int.did_dma_delay = 0;
1407 /* clear "did_close" flag */
1408 xfer->flags_int.did_close = 0;
1411 /* clear "bdma_setup" flag */
1412 xfer->flags_int.bdma_setup = 0;
1414 /* by default we cannot cancel any USB transfer immediately */
1415 xfer->flags_int.can_cancel_immed = 0;
1417 /* clear lengths and frame counts by default */
1422 /* clear any previous errors */
1427 if (xfer->nframes == 0) {
1428 if (xfer->flags.stall_pipe) {
1430 * Special case - want to stall without transferring
1433 DPRINTF("xfer=%p nframes=0: stall "
1434 "or clear stall!\n", xfer);
1435 USB_BUS_LOCK(xfer->xroot->bus);
1436 xfer->flags_int.can_cancel_immed = 1;
1437 /* start the transfer */
1438 usb2_command_wrapper(&xfer->pipe->pipe_q, xfer);
1439 USB_BUS_UNLOCK(xfer->xroot->bus);
1442 USB_BUS_LOCK(xfer->xroot->bus);
1443 usb2_transfer_done(xfer, USB_ERR_INVAL);
1444 USB_BUS_UNLOCK(xfer->xroot->bus);
1447 /* compute total transfer length */
1449 for (x = 0; x != xfer->nframes; x++) {
1450 xfer->sumlen += xfer->frlengths[x];
1451 if (xfer->sumlen < xfer->frlengths[x]) {
1452 /* length wrapped around */
1453 USB_BUS_LOCK(xfer->xroot->bus);
1454 usb2_transfer_done(xfer, USB_ERR_INVAL);
1455 USB_BUS_UNLOCK(xfer->xroot->bus);
1460 /* clear some internal flags */
1462 xfer->flags_int.short_xfer_ok = 0;
1463 xfer->flags_int.short_frames_ok = 0;
1465 /* check if this is a control transfer */
1467 if (xfer->flags_int.control_xfr) {
1469 if (usb2_start_hardware_sub(xfer)) {
1470 USB_BUS_LOCK(xfer->xroot->bus);
1471 usb2_transfer_done(xfer, USB_ERR_STALLED);
1472 USB_BUS_UNLOCK(xfer->xroot->bus);
1477 * Setup filtered version of some transfer flags,
1478 * in case of data read direction
1480 if (USB_GET_DATA_ISREAD(xfer)) {
1482 if (xfer->flags.short_frames_ok) {
1483 xfer->flags_int.short_xfer_ok = 1;
1484 xfer->flags_int.short_frames_ok = 1;
1485 } else if (xfer->flags.short_xfer_ok) {
1486 xfer->flags_int.short_xfer_ok = 1;
1488 /* check for control transfer */
1489 if (xfer->flags_int.control_xfr) {
1491 * 1) Control transfers do not support
1492 * reception of multiple short USB
1493 * frames in host mode and device side
1494 * mode, with exception of:
1496 * 2) Due to sometimes buggy device
1497 * side firmware we need to do a
1498 * STATUS stage in case of short
1499 * control transfers in USB host mode.
1500 * The STATUS stage then becomes the
1501 * "alt_next" to the DATA stage.
1503 xfer->flags_int.short_frames_ok = 1;
1508 * Check if BUS-DMA support is enabled and try to load virtual
1509 * buffers into DMA, if any:
1512 if (xfer->flags_int.bdma_enable) {
1513 /* insert the USB transfer last in the BUS-DMA queue */
1514 usb2_command_wrapper(&xfer->xroot->dma_q, xfer);
1519 * Enter the USB transfer into the Host Controller or
1520 * Device Controller schedule:
1522 usb2_pipe_enter(xfer);
1525 /*------------------------------------------------------------------------*
1526 * usb2_pipe_enter - factored out code
1527 *------------------------------------------------------------------------*/
1529 usb2_pipe_enter(struct usb2_xfer *xfer)
1531 struct usb2_pipe *pipe;
1533 USB_XFER_LOCK_ASSERT(xfer, MA_OWNED);
1535 USB_BUS_LOCK(xfer->xroot->bus);
1541 /* enter the transfer */
1542 (pipe->methods->enter) (xfer);
1544 xfer->flags_int.can_cancel_immed = 1;
1546 /* check for transfer error */
1548 /* some error has happened */
1549 usb2_transfer_done(xfer, 0);
1550 USB_BUS_UNLOCK(xfer->xroot->bus);
1554 /* start the transfer */
1555 usb2_command_wrapper(&pipe->pipe_q, xfer);
1556 USB_BUS_UNLOCK(xfer->xroot->bus);
1559 /*------------------------------------------------------------------------*
1560 * usb2_transfer_start - start an USB transfer
1562 * NOTE: Calling this function more than one time will only
1563 * result in a single transfer start, until the USB transfer
1565 *------------------------------------------------------------------------*/
1567 usb2_transfer_start(struct usb2_xfer *xfer)
1570 /* transfer is gone */
1573 USB_XFER_LOCK_ASSERT(xfer, MA_OWNED);
1575 /* mark the USB transfer started */
1577 if (!xfer->flags_int.started) {
1578 xfer->flags_int.started = 1;
1580 /* check if the USB transfer callback is already transferring */
1582 if (xfer->flags_int.transferring) {
1585 USB_BUS_LOCK(xfer->xroot->bus);
1586 /* call the USB transfer callback */
1587 usb2_callback_ss_done_defer(xfer);
1588 USB_BUS_UNLOCK(xfer->xroot->bus);
1591 /*------------------------------------------------------------------------*
1592 * usb2_transfer_stop - stop an USB transfer
1594 * NOTE: Calling this function more than one time will only
1595 * result in a single transfer stop.
1596 * NOTE: When this function returns it is not safe to free nor
1597 * reuse any DMA buffers. See "usb2_transfer_drain()".
1598 *------------------------------------------------------------------------*/
1600 usb2_transfer_stop(struct usb2_xfer *xfer)
1602 struct usb2_pipe *pipe;
1605 /* transfer is gone */
1608 USB_XFER_LOCK_ASSERT(xfer, MA_OWNED);
1610 /* check if the USB transfer was ever opened */
1612 if (!xfer->flags_int.open) {
1613 /* nothing to do except clearing the "started" flag */
1614 xfer->flags_int.started = 0;
1617 /* try to stop the current USB transfer */
1619 USB_BUS_LOCK(xfer->xroot->bus);
1620 xfer->error = USB_ERR_CANCELLED;/* override any previous error */
1622 * Clear "open" and "started" when both private and USB lock
1623 * is locked so that we don't get a race updating "flags_int"
1625 xfer->flags_int.open = 0;
1626 xfer->flags_int.started = 0;
1629 * Check if we can cancel the USB transfer immediately.
1631 if (xfer->flags_int.transferring) {
1632 if (xfer->flags_int.can_cancel_immed &&
1633 (!xfer->flags_int.did_close)) {
1636 * The following will lead to an USB_ERR_CANCELLED
1637 * error code being passed to the USB callback.
1639 (xfer->pipe->methods->close) (xfer);
1640 /* only close once */
1641 xfer->flags_int.did_close = 1;
1643 /* need to wait for the next done callback */
1648 /* close here and now */
1649 (xfer->pipe->methods->close) (xfer);
1652 * Any additional DMA delay is done by
1653 * "usb2_transfer_unsetup()".
1657 * Special case. Check if we need to restart a blocked
1663 * If the current USB transfer is completing we need
1664 * to start the next one:
1666 if (pipe->pipe_q.curr == xfer) {
1667 usb2_command_wrapper(&pipe->pipe_q, NULL);
1671 USB_BUS_UNLOCK(xfer->xroot->bus);
1674 /*------------------------------------------------------------------------*
1675 * usb2_transfer_pending
1677 * This function will check if an USB transfer is pending which is a
1678 * little bit complicated!
1681 * 1: Pending: The USB transfer will receive a callback in the future.
1682 *------------------------------------------------------------------------*/
1684 usb2_transfer_pending(struct usb2_xfer *xfer)
1686 struct usb2_xfer_root *info;
1687 struct usb2_xfer_queue *pq;
1690 /* transfer is gone */
1693 USB_XFER_LOCK_ASSERT(xfer, MA_OWNED);
1695 if (xfer->flags_int.transferring) {
1699 USB_BUS_LOCK(xfer->xroot->bus);
1700 if (xfer->wait_queue) {
1701 /* we are waiting on a queue somewhere */
1702 USB_BUS_UNLOCK(xfer->xroot->bus);
1708 if (pq->curr == xfer) {
1709 /* we are currently scheduled for callback */
1710 USB_BUS_UNLOCK(xfer->xroot->bus);
1713 /* we are not pending */
1714 USB_BUS_UNLOCK(xfer->xroot->bus);
1718 /*------------------------------------------------------------------------*
1719 * usb2_transfer_drain
1721 * This function will stop the USB transfer and wait for any
1722 * additional BUS-DMA and HW-DMA operations to complete. Buffers that
1723 * are loaded into DMA can safely be freed or reused after that this
1724 * function has returned.
1725 *------------------------------------------------------------------------*/
1727 usb2_transfer_drain(struct usb2_xfer *xfer)
1729 WITNESS_WARN(WARN_GIANTOK | WARN_SLEEPOK, NULL,
1730 "usb2_transfer_drain can sleep!");
1733 /* transfer is gone */
1736 if (xfer->xroot->xfer_mtx != &Giant) {
1737 USB_XFER_LOCK_ASSERT(xfer, MA_NOTOWNED);
1739 USB_XFER_LOCK(xfer);
1741 usb2_transfer_stop(xfer);
1743 while (usb2_transfer_pending(xfer)) {
1744 xfer->flags_int.draining = 1;
1746 * Wait until the current outstanding USB
1747 * transfer is complete !
1749 usb2_cv_wait(&xfer->xroot->cv_drain, xfer->xroot->xfer_mtx);
1751 USB_XFER_UNLOCK(xfer);
1754 /*------------------------------------------------------------------------*
1755 * usb2_set_frame_data
1757 * This function sets the pointer of the buffer that should
1758 * loaded directly into DMA for the given USB frame. Passing "ptr"
1759 * equal to NULL while the corresponding "frlength" is greater
1760 * than zero gives undefined results!
1761 *------------------------------------------------------------------------*/
1763 usb2_set_frame_data(struct usb2_xfer *xfer, void *ptr, usb2_frcount_t frindex)
1765 /* set virtual address to load and length */
1766 xfer->frbuffers[frindex].buffer = ptr;
1769 /*------------------------------------------------------------------------*
1770 * usb2_set_frame_offset
1772 * This function sets the frame data buffer offset relative to the beginning
1773 * of the USB DMA buffer allocated for this USB transfer.
1774 *------------------------------------------------------------------------*/
1776 usb2_set_frame_offset(struct usb2_xfer *xfer, usb2_frlength_t offset,
1777 usb2_frcount_t frindex)
1779 USB_ASSERT(!xfer->flags.ext_buffer, ("Cannot offset data frame "
1780 "when the USB buffer is external!\n"));
1782 /* set virtual address to load */
1783 xfer->frbuffers[frindex].buffer =
1784 USB_ADD_BYTES(xfer->local_buffer, offset);
1787 /*------------------------------------------------------------------------*
1788 * usb2_callback_proc - factored out code
1790 * This function performs USB callbacks.
1791 *------------------------------------------------------------------------*/
1793 usb2_callback_proc(struct usb2_proc_msg *_pm)
1795 struct usb2_done_msg *pm = (void *)_pm;
1796 struct usb2_xfer_root *info = pm->xroot;
1798 /* Change locking order */
1799 USB_BUS_UNLOCK(info->bus);
1802 * We exploit the fact that the mutex is the same for all
1803 * callbacks that will be called from this thread:
1805 mtx_lock(info->xfer_mtx);
1806 USB_BUS_LOCK(info->bus);
1808 /* Continue where we lost track */
1809 usb2_command_wrapper(&info->done_q,
1812 mtx_unlock(info->xfer_mtx);
1815 /*------------------------------------------------------------------------*
1816 * usb2_callback_ss_done_defer
1818 * This function will defer the start, stop and done callback to the
1820 *------------------------------------------------------------------------*/
1822 usb2_callback_ss_done_defer(struct usb2_xfer *xfer)
1824 struct usb2_xfer_root *info = xfer->xroot;
1825 struct usb2_xfer_queue *pq = &info->done_q;
1827 USB_BUS_LOCK_ASSERT(xfer->xroot->bus, MA_OWNED);
1829 if (pq->curr != xfer) {
1830 usb2_transfer_enqueue(pq, xfer);
1832 if (!pq->recurse_1) {
1835 * We have to postpone the callback due to the fact we
1836 * will have a Lock Order Reversal, LOR, if we try to
1839 if (usb2_proc_msignal(info->done_p,
1840 &info->done_m[0], &info->done_m[1])) {
1844 /* clear second recurse flag */
1851 /*------------------------------------------------------------------------*
1852 * usb2_callback_wrapper
1854 * This is a wrapper for USB callbacks. This wrapper does some
1855 * auto-magic things like figuring out if we can call the callback
1856 * directly from the current context or if we need to wakeup the
1857 * interrupt process.
1858 *------------------------------------------------------------------------*/
1860 usb2_callback_wrapper(struct usb2_xfer_queue *pq)
1862 struct usb2_xfer *xfer = pq->curr;
1863 struct usb2_xfer_root *info = xfer->xroot;
1865 USB_BUS_LOCK_ASSERT(info->bus, MA_OWNED);
1866 if (!mtx_owned(info->xfer_mtx)) {
1868 * Cases that end up here:
1870 * 5) HW interrupt done callback or other source.
1872 DPRINTFN(3, "case 5\n");
1875 * We have to postpone the callback due to the fact we
1876 * will have a Lock Order Reversal, LOR, if we try to
1879 if (usb2_proc_msignal(info->done_p,
1880 &info->done_m[0], &info->done_m[1])) {
1886 * Cases that end up here:
1888 * 1) We are starting a transfer
1889 * 2) We are prematurely calling back a transfer
1890 * 3) We are stopping a transfer
1891 * 4) We are doing an ordinary callback
1893 DPRINTFN(3, "case 1-4\n");
1894 /* get next USB transfer in the queue */
1895 info->done_q.curr = NULL;
1897 USB_BUS_UNLOCK(info->bus);
1898 USB_BUS_LOCK_ASSERT(info->bus, MA_NOTOWNED);
1900 /* set correct USB state for callback */
1901 if (!xfer->flags_int.transferring) {
1902 xfer->usb2_state = USB_ST_SETUP;
1903 if (!xfer->flags_int.started) {
1904 /* we got stopped before we even got started */
1905 USB_BUS_LOCK(info->bus);
1910 if (usb2_callback_wrapper_sub(xfer)) {
1911 /* the callback has been deferred */
1912 USB_BUS_LOCK(info->bus);
1916 /* decrement power reference */
1917 usb2_transfer_power_ref(xfer, -1);
1919 xfer->flags_int.transferring = 0;
1922 xfer->usb2_state = USB_ST_ERROR;
1924 /* set transferred state */
1925 xfer->usb2_state = USB_ST_TRANSFERRED;
1927 /* sync DMA memory, if any */
1928 if (xfer->flags_int.bdma_enable &&
1929 (!xfer->flags_int.bdma_no_post_sync)) {
1930 usb2_bdma_post_sync(xfer);
1936 /* call processing routine */
1937 (xfer->callback) (xfer);
1939 /* pickup the USB mutex again */
1940 USB_BUS_LOCK(info->bus);
1943 * Check if we got started after that we got cancelled, but
1944 * before we managed to do the callback.
1946 if ((!xfer->flags_int.open) &&
1947 (xfer->flags_int.started) &&
1948 (xfer->usb2_state == USB_ST_ERROR)) {
1949 /* try to loop, but not recursivly */
1950 usb2_command_wrapper(&info->done_q, xfer);
1956 * Check if we are draining.
1958 if (xfer->flags_int.draining &&
1959 (!xfer->flags_int.transferring)) {
1960 /* "usb2_transfer_drain()" is waiting for end of transfer */
1961 xfer->flags_int.draining = 0;
1962 usb2_cv_broadcast(&info->cv_drain);
1965 /* do the next callback, if any */
1966 usb2_command_wrapper(&info->done_q,
1970 /*------------------------------------------------------------------------*
1971 * usb2_dma_delay_done_cb
1973 * This function is called when the DMA delay has been exectuded, and
1974 * will make sure that the callback is called to complete the USB
1975 * transfer. This code path is ususally only used when there is an USB
1976 * error like USB_ERR_CANCELLED.
1977 *------------------------------------------------------------------------*/
1979 usb2_dma_delay_done_cb(void *arg)
1981 struct usb2_xfer *xfer = arg;
1983 USB_BUS_LOCK_ASSERT(xfer->xroot->bus, MA_OWNED);
1985 DPRINTFN(3, "Completed %p\n", xfer);
1987 /* queue callback for execution, again */
1988 usb2_transfer_done(xfer, 0);
1991 /*------------------------------------------------------------------------*
1992 * usb2_transfer_dequeue
1994 * - This function is used to remove an USB transfer from a USB
1997 * - This function can be called multiple times in a row.
1998 *------------------------------------------------------------------------*/
2000 usb2_transfer_dequeue(struct usb2_xfer *xfer)
2002 struct usb2_xfer_queue *pq;
2004 pq = xfer->wait_queue;
2006 TAILQ_REMOVE(&pq->head, xfer, wait_entry);
2007 xfer->wait_queue = NULL;
2011 /*------------------------------------------------------------------------*
2012 * usb2_transfer_enqueue
2014 * - This function is used to insert an USB transfer into a USB *
2017 * - This function can be called multiple times in a row.
2018 *------------------------------------------------------------------------*/
2020 usb2_transfer_enqueue(struct usb2_xfer_queue *pq, struct usb2_xfer *xfer)
2023 * Insert the USB transfer into the queue, if it is not
2024 * already on a USB transfer queue:
2026 if (xfer->wait_queue == NULL) {
2027 xfer->wait_queue = pq;
2028 TAILQ_INSERT_TAIL(&pq->head, xfer, wait_entry);
2032 /*------------------------------------------------------------------------*
2033 * usb2_transfer_done
2035 * - This function is used to remove an USB transfer from the busdma,
2036 * pipe or interrupt queue.
2038 * - This function is used to queue the USB transfer on the done
2041 * - This function is used to stop any USB transfer timeouts.
2042 *------------------------------------------------------------------------*/
2044 usb2_transfer_done(struct usb2_xfer *xfer, usb2_error_t error)
2046 USB_BUS_LOCK_ASSERT(xfer->xroot->bus, MA_OWNED);
2048 DPRINTF("err=%s\n", usb2_errstr(error));
2051 * If we are not transferring then just return.
2052 * This can happen during transfer cancel.
2054 if (!xfer->flags_int.transferring) {
2055 DPRINTF("not transferring\n");
2058 /* only set transfer error if not already set */
2060 xfer->error = error;
2062 /* stop any callouts */
2063 usb2_callout_stop(&xfer->timeout_handle);
2066 * If we are waiting on a queue, just remove the USB transfer
2067 * from the queue, if any. We should have the required locks
2068 * locked to do the remove when this function is called.
2070 usb2_transfer_dequeue(xfer);
2073 if (mtx_owned(xfer->xroot->xfer_mtx)) {
2074 struct usb2_xfer_queue *pq;
2077 * If the private USB lock is not locked, then we assume
2078 * that the BUS-DMA load stage has been passed:
2080 pq = &xfer->xroot->dma_q;
2082 if (pq->curr == xfer) {
2083 /* start the next BUS-DMA load, if any */
2084 usb2_command_wrapper(pq, NULL);
2088 /* keep some statistics */
2090 xfer->xroot->bus->stats_err.uds_requests
2091 [xfer->pipe->edesc->bmAttributes & UE_XFERTYPE]++;
2093 xfer->xroot->bus->stats_ok.uds_requests
2094 [xfer->pipe->edesc->bmAttributes & UE_XFERTYPE]++;
2097 /* call the USB transfer callback */
2098 usb2_callback_ss_done_defer(xfer);
2101 /*------------------------------------------------------------------------*
2102 * usb2_transfer_start_cb
2104 * This function is called to start the USB transfer when
2105 * "xfer->interval" is greater than zero, and and the endpoint type is
2107 *------------------------------------------------------------------------*/
2109 usb2_transfer_start_cb(void *arg)
2111 struct usb2_xfer *xfer = arg;
2112 struct usb2_pipe *pipe = xfer->pipe;
2114 USB_BUS_LOCK_ASSERT(xfer->xroot->bus, MA_OWNED);
2118 /* start the transfer */
2119 (pipe->methods->start) (xfer);
2121 xfer->flags_int.can_cancel_immed = 1;
2123 /* check for error */
2125 /* some error has happened */
2126 usb2_transfer_done(xfer, 0);
2130 /*------------------------------------------------------------------------*
2131 * usb2_transfer_set_stall
2133 * This function is used to set the stall flag outside the
2134 * callback. This function is NULL safe.
2135 *------------------------------------------------------------------------*/
2137 usb2_transfer_set_stall(struct usb2_xfer *xfer)
2143 USB_XFER_LOCK_ASSERT(xfer, MA_OWNED);
2145 /* avoid any races by locking the USB mutex */
2146 USB_BUS_LOCK(xfer->xroot->bus);
2148 xfer->flags.stall_pipe = 1;
2150 USB_BUS_UNLOCK(xfer->xroot->bus);
2153 /*------------------------------------------------------------------------*
2154 * usb2_transfer_clear_stall
2156 * This function is used to clear the stall flag outside the
2157 * callback. This function is NULL safe.
2158 *------------------------------------------------------------------------*/
2160 usb2_transfer_clear_stall(struct usb2_xfer *xfer)
2166 USB_XFER_LOCK_ASSERT(xfer, MA_OWNED);
2168 /* avoid any races by locking the USB mutex */
2169 USB_BUS_LOCK(xfer->xroot->bus);
2171 xfer->flags.stall_pipe = 0;
2173 USB_BUS_UNLOCK(xfer->xroot->bus);
2176 /*------------------------------------------------------------------------*
2179 * This function is used to add an USB transfer to the pipe transfer list.
2180 *------------------------------------------------------------------------*/
2182 usb2_pipe_start(struct usb2_xfer_queue *pq)
2184 struct usb2_pipe *pipe;
2185 struct usb2_xfer *xfer;
2191 USB_BUS_LOCK_ASSERT(xfer->xroot->bus, MA_OWNED);
2194 * If the pipe is already stalled we do nothing !
2196 if (pipe->is_stalled) {
2200 * Check if we are supposed to stall the pipe:
2202 if (xfer->flags.stall_pipe) {
2203 /* clear stall command */
2204 xfer->flags.stall_pipe = 0;
2207 * Only stall BULK and INTERRUPT endpoints.
2209 type = (pipe->edesc->bmAttributes & UE_XFERTYPE);
2210 if ((type == UE_BULK) ||
2211 (type == UE_INTERRUPT)) {
2212 struct usb2_device *udev;
2213 struct usb2_xfer_root *info;
2217 pipe->is_stalled = 1;
2219 if (udev->flags.usb2_mode == USB_MODE_DEVICE) {
2220 (udev->bus->methods->set_stall) (
2222 } else if (udev->default_xfer[1]) {
2223 info = udev->default_xfer[1]->xroot;
2224 if (usb2_proc_msignal(
2225 &info->bus->non_giant_callback_proc,
2226 &udev->cs_msg[0], &udev->cs_msg[1])) {
2230 /* should not happen */
2231 DPRINTFN(0, "No stall handler!\n");
2234 * We get started again when the stall is cleared!
2239 /* Set or clear stall complete - special case */
2240 if (xfer->nframes == 0) {
2241 /* we are complete */
2243 usb2_transfer_done(xfer, 0);
2249 * 1) Start the first transfer queued.
2251 * 2) Re-start the current USB transfer.
2254 * Check if there should be any
2255 * pre transfer start delay:
2257 if (xfer->interval > 0) {
2258 type = (pipe->edesc->bmAttributes & UE_XFERTYPE);
2259 if ((type == UE_BULK) ||
2260 (type == UE_CONTROL)) {
2261 usb2_transfer_timeout_ms(xfer,
2262 &usb2_transfer_start_cb,
2269 /* start USB transfer */
2270 (pipe->methods->start) (xfer);
2272 xfer->flags_int.can_cancel_immed = 1;
2274 /* check for error */
2276 /* some error has happened */
2277 usb2_transfer_done(xfer, 0);
2281 /*------------------------------------------------------------------------*
2282 * usb2_transfer_timeout_ms
2284 * This function is used to setup a timeout on the given USB
2285 * transfer. If the timeout has been deferred the callback given by
2286 * "cb" will get called after "ms" milliseconds.
2287 *------------------------------------------------------------------------*/
2289 usb2_transfer_timeout_ms(struct usb2_xfer *xfer,
2290 void (*cb) (void *arg), usb2_timeout_t ms)
2292 USB_BUS_LOCK_ASSERT(xfer->xroot->bus, MA_OWNED);
2295 usb2_callout_reset(&xfer->timeout_handle,
2296 USB_MS_TO_TICKS(ms), cb, xfer);
2299 /*------------------------------------------------------------------------*
2300 * usb2_callback_wrapper_sub
2302 * - This function will update variables in an USB transfer after
2303 * that the USB transfer is complete.
2305 * - This function is used to start the next USB transfer on the
2306 * pipe transfer queue, if any.
2308 * NOTE: In some special cases the USB transfer will not be removed from
2309 * the pipe queue, but remain first. To enforce USB transfer removal call
2310 * this function passing the error code "USB_ERR_CANCELLED".
2314 * Else: The callback has been deferred.
2315 *------------------------------------------------------------------------*/
2317 usb2_callback_wrapper_sub(struct usb2_xfer *xfer)
2319 struct usb2_pipe *pipe;
2322 if ((!xfer->flags_int.open) &&
2323 (!xfer->flags_int.did_close)) {
2325 USB_BUS_LOCK(xfer->xroot->bus);
2326 (xfer->pipe->methods->close) (xfer);
2327 USB_BUS_UNLOCK(xfer->xroot->bus);
2328 /* only close once */
2329 xfer->flags_int.did_close = 1;
2330 return (1); /* wait for new callback */
2333 * If we have a non-hardware induced error we
2334 * need to do the DMA delay!
2336 if (((xfer->error == USB_ERR_CANCELLED) ||
2337 (xfer->error == USB_ERR_TIMEOUT)) &&
2338 (!xfer->flags_int.did_dma_delay)) {
2340 usb2_timeout_t temp;
2342 /* only delay once */
2343 xfer->flags_int.did_dma_delay = 1;
2345 /* we can not cancel this delay */
2346 xfer->flags_int.can_cancel_immed = 0;
2348 temp = usb2_get_dma_delay(xfer->xroot->bus);
2350 DPRINTFN(3, "DMA delay, %u ms, "
2351 "on %p\n", temp, xfer);
2354 USB_BUS_LOCK(xfer->xroot->bus);
2355 usb2_transfer_timeout_ms(xfer,
2356 &usb2_dma_delay_done_cb, temp);
2357 USB_BUS_UNLOCK(xfer->xroot->bus);
2358 return (1); /* wait for new callback */
2361 /* check actual number of frames */
2362 if (xfer->aframes > xfer->nframes) {
2363 if (xfer->error == 0) {
2364 panic("%s: actual number of frames, %d, is "
2365 "greater than initial number of frames, %d!\n",
2366 __FUNCTION__, xfer->aframes, xfer->nframes);
2368 /* just set some valid value */
2369 xfer->aframes = xfer->nframes;
2372 /* compute actual length */
2375 for (x = 0; x != xfer->aframes; x++) {
2376 xfer->actlen += xfer->frlengths[x];
2380 * Frames that were not transferred get zero actual length in
2381 * case the USB device driver does not check the actual number
2382 * of frames transferred, "xfer->aframes":
2384 for (; x < xfer->nframes; x++) {
2385 xfer->frlengths[x] = 0;
2388 /* check actual length */
2389 if (xfer->actlen > xfer->sumlen) {
2390 if (xfer->error == 0) {
2391 panic("%s: actual length, %d, is greater than "
2392 "initial length, %d!\n",
2393 __FUNCTION__, xfer->actlen, xfer->sumlen);
2395 /* just set some valid value */
2396 xfer->actlen = xfer->sumlen;
2399 DPRINTFN(6, "xfer=%p pipe=%p sts=%d alen=%d, slen=%d, afrm=%d, nfrm=%d\n",
2400 xfer, xfer->pipe, xfer->error, xfer->actlen, xfer->sumlen,
2401 xfer->aframes, xfer->nframes);
2404 /* end of control transfer, if any */
2405 xfer->flags_int.control_act = 0;
2407 /* check if we should block the execution queue */
2408 if ((xfer->error != USB_ERR_CANCELLED) &&
2409 (xfer->flags.pipe_bof)) {
2410 DPRINTFN(2, "xfer=%p: Block On Failure "
2411 "on pipe=%p\n", xfer, xfer->pipe);
2415 /* check for short transfers */
2416 if (xfer->actlen < xfer->sumlen) {
2418 /* end of control transfer, if any */
2419 xfer->flags_int.control_act = 0;
2421 if (!xfer->flags_int.short_xfer_ok) {
2422 xfer->error = USB_ERR_SHORT_XFER;
2423 if (xfer->flags.pipe_bof) {
2424 DPRINTFN(2, "xfer=%p: Block On Failure on "
2425 "Short Transfer on pipe %p.\n",
2432 * Check if we are in the middle of a
2435 if (xfer->flags_int.control_act) {
2436 DPRINTFN(5, "xfer=%p: Control transfer "
2437 "active on pipe=%p\n", xfer, xfer->pipe);
2446 * If the current USB transfer is completing we need to start the
2449 USB_BUS_LOCK(xfer->xroot->bus);
2450 if (pipe->pipe_q.curr == xfer) {
2451 usb2_command_wrapper(&pipe->pipe_q, NULL);
2453 if (pipe->pipe_q.curr || TAILQ_FIRST(&pipe->pipe_q.head)) {
2454 /* there is another USB transfer waiting */
2456 /* this is the last USB transfer */
2457 /* clear isochronous sync flag */
2458 xfer->pipe->is_synced = 0;
2461 USB_BUS_UNLOCK(xfer->xroot->bus);
2466 /*------------------------------------------------------------------------*
2467 * usb2_command_wrapper
2469 * This function is used to execute commands non-recursivly on an USB
2471 *------------------------------------------------------------------------*/
2473 usb2_command_wrapper(struct usb2_xfer_queue *pq, struct usb2_xfer *xfer)
2477 * If the transfer is not already processing,
2480 if (pq->curr != xfer) {
2481 usb2_transfer_enqueue(pq, xfer);
2482 if (pq->curr != NULL) {
2483 /* something is already processing */
2484 DPRINTFN(6, "busy %p\n", pq->curr);
2489 /* Get next element in queue */
2493 if (!pq->recurse_1) {
2497 /* set both recurse flags */
2501 if (pq->curr == NULL) {
2502 xfer = TAILQ_FIRST(&pq->head);
2504 TAILQ_REMOVE(&pq->head, xfer,
2506 xfer->wait_queue = NULL;
2512 DPRINTFN(6, "cb %p (enter)\n", pq->curr);
2514 DPRINTFN(6, "cb %p (leave)\n", pq->curr);
2516 } while (!pq->recurse_2);
2518 /* clear first recurse flag */
2522 /* clear second recurse flag */
2527 /*------------------------------------------------------------------------*
2528 * usb2_default_transfer_setup
2530 * This function is used to setup the default USB control endpoint
2532 *------------------------------------------------------------------------*/
2534 usb2_default_transfer_setup(struct usb2_device *udev)
2536 struct usb2_xfer *xfer;
2538 uint8_t iface_index;
2540 /* check for root HUB */
2541 if (udev->parent_hub == NULL)
2545 xfer = udev->default_xfer[0];
2547 USB_XFER_LOCK(xfer);
2549 ((xfer->address == udev->address) &&
2550 (udev->default_ep_desc.wMaxPacketSize[0] ==
2551 udev->ddesc.bMaxPacketSize));
2552 if (udev->flags.usb2_mode == USB_MODE_DEVICE) {
2555 * NOTE: checking "xfer->address" and
2556 * starting the USB transfer must be
2559 usb2_transfer_start(xfer);
2562 USB_XFER_UNLOCK(xfer);
2569 * All parameters are exactly the same like before.
2575 * Update wMaxPacketSize for the default control endpoint:
2577 udev->default_ep_desc.wMaxPacketSize[0] =
2578 udev->ddesc.bMaxPacketSize;
2581 * Unsetup any existing USB transfer:
2583 usb2_transfer_unsetup(udev->default_xfer, USB_DEFAULT_XFER_MAX);
2586 * Try to setup a new USB transfer for the
2587 * default control endpoint:
2590 if (usb2_transfer_setup(udev, &iface_index,
2591 udev->default_xfer, usb2_control_ep_cfg, USB_DEFAULT_XFER_MAX, NULL,
2592 udev->default_mtx)) {
2593 DPRINTFN(0, "could not setup default "
2600 /*------------------------------------------------------------------------*
2601 * usb2_clear_data_toggle - factored out code
2603 * NOTE: the intention of this function is not to reset the hardware
2605 *------------------------------------------------------------------------*/
2607 usb2_clear_data_toggle(struct usb2_device *udev, struct usb2_pipe *pipe)
2609 DPRINTFN(5, "udev=%p pipe=%p\n", udev, pipe);
2611 USB_BUS_LOCK(udev->bus);
2612 pipe->toggle_next = 0;
2613 USB_BUS_UNLOCK(udev->bus);
2616 /*------------------------------------------------------------------------*
2617 * usb2_clear_stall_callback - factored out clear stall callback
2620 * xfer1: Clear Stall Control Transfer
2621 * xfer2: Stalled USB Transfer
2623 * This function is NULL safe.
2629 * Clear stall config example:
2631 * static const struct usb2_config my_clearstall = {
2632 * .type = UE_CONTROL,
2634 * .direction = UE_DIR_ANY,
2635 * .interval = 50, //50 milliseconds
2636 * .bufsize = sizeof(struct usb2_device_request),
2637 * .timeout = 1000, //1.000 seconds
2638 * .callback = &my_clear_stall_callback, // **
2639 * .usb_mode = USB_MODE_HOST,
2642 * ** "my_clear_stall_callback" calls "usb2_clear_stall_callback"
2643 * passing the correct parameters.
2644 *------------------------------------------------------------------------*/
2646 usb2_clear_stall_callback(struct usb2_xfer *xfer1,
2647 struct usb2_xfer *xfer2)
2649 struct usb2_device_request req;
2651 if (xfer2 == NULL) {
2652 /* looks like we are tearing down */
2653 DPRINTF("NULL input parameter\n");
2656 USB_XFER_LOCK_ASSERT(xfer1, MA_OWNED);
2657 USB_XFER_LOCK_ASSERT(xfer2, MA_OWNED);
2659 switch (USB_GET_STATE(xfer1)) {
2663 * pre-clear the data toggle to DATA0 ("umass.c" and
2664 * "ata-usb.c" depends on this)
2667 usb2_clear_data_toggle(xfer2->xroot->udev, xfer2->pipe);
2669 /* setup a clear-stall packet */
2671 req.bmRequestType = UT_WRITE_ENDPOINT;
2672 req.bRequest = UR_CLEAR_FEATURE;
2673 USETW(req.wValue, UF_ENDPOINT_HALT);
2674 req.wIndex[0] = xfer2->pipe->edesc->bEndpointAddress;
2676 USETW(req.wLength, 0);
2679 * "usb2_transfer_setup_sub()" will ensure that
2680 * we have sufficient room in the buffer for
2681 * the request structure!
2684 /* copy in the transfer */
2686 usb2_copy_in(xfer1->frbuffers, 0, &req, sizeof(req));
2689 xfer1->frlengths[0] = sizeof(req);
2692 usb2_start_hardware(xfer1);
2695 case USB_ST_TRANSFERRED:
2698 default: /* Error */
2699 if (xfer1->error == USB_ERR_CANCELLED) {
2704 return (1); /* Clear Stall Finished */
2708 usb2_do_poll(struct usb2_xfer **ppxfer, uint16_t max)
2710 static uint8_t once = 0;
2711 /* polling is currently not supported */
2714 printf("usb2_do_poll: USB polling is "
2715 "not supported!\n");
2720 usb2_get_std_packet_size(struct usb2_std_packet_size *ptr,
2721 uint8_t type, uint8_t usb_speed)
2723 static const uint16_t intr_range_max[USB_SPEED_MAX] = {
2724 [USB_SPEED_LOW] = 8,
2725 [USB_SPEED_FULL] = 64,
2726 [USB_SPEED_HIGH] = 1024,
2727 [USB_SPEED_VARIABLE] = 1024,
2728 [USB_SPEED_SUPER] = 1024,
2731 static const uint16_t isoc_range_max[USB_SPEED_MAX] = {
2732 [USB_SPEED_LOW] = 0, /* invalid */
2733 [USB_SPEED_FULL] = 1023,
2734 [USB_SPEED_HIGH] = 1024,
2735 [USB_SPEED_VARIABLE] = 3584,
2736 [USB_SPEED_SUPER] = 1024,
2739 static const uint16_t control_min[USB_SPEED_MAX] = {
2740 [USB_SPEED_LOW] = 8,
2741 [USB_SPEED_FULL] = 8,
2742 [USB_SPEED_HIGH] = 64,
2743 [USB_SPEED_VARIABLE] = 512,
2744 [USB_SPEED_SUPER] = 512,
2747 static const uint16_t bulk_min[USB_SPEED_MAX] = {
2748 [USB_SPEED_LOW] = 0, /* not supported */
2749 [USB_SPEED_FULL] = 8,
2750 [USB_SPEED_HIGH] = 512,
2751 [USB_SPEED_VARIABLE] = 512,
2752 [USB_SPEED_SUPER] = 1024,
2757 memset(ptr, 0, sizeof(*ptr));
2761 ptr->range.max = intr_range_max[usb_speed];
2763 case UE_ISOCHRONOUS:
2764 ptr->range.max = isoc_range_max[usb_speed];
2767 if (type == UE_BULK)
2768 temp = bulk_min[usb_speed];
2769 else /* UE_CONTROL */
2770 temp = control_min[usb_speed];
2772 /* default is fixed */
2773 ptr->fixed[0] = temp;
2774 ptr->fixed[1] = temp;
2775 ptr->fixed[2] = temp;
2776 ptr->fixed[3] = temp;
2778 if (usb_speed == USB_SPEED_FULL) {
2779 /* multiple sizes */
2784 if ((usb_speed == USB_SPEED_VARIABLE) &&
2785 (type == UE_BULK)) {
2786 /* multiple sizes */
2787 ptr->fixed[2] = 1024;
2788 ptr->fixed[3] = 1536;