2 * Copyright (C) 2013 Marek Vasut <marex@denx.de>
4 * The code contained herein is licensed under the GNU General Public
5 * License. You may obtain a copy of the GNU General Public License
6 * Version 2 or later at the following locations:
8 * http://www.opensource.org/licenses/gpl-license.html
9 * http://www.gnu.org/copyleft/gpl.html
17 compatible = "msr,m28cu3", "fsl,imx28";
20 device_type = "memory";
21 reg = <0x40000000 0x08000000>;
29 pinctrl-names = "default";
30 pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
34 label = "gpmi-nfc-0-boot";
35 reg = <0x00000000 0x01400000>;
40 label = "gpmi-nfc-general-use";
41 reg = <0x01400000 0x0ec00000>;
46 compatible = "fsl,imx28-mmc";
47 pinctrl-names = "default";
48 pinctrl-0 = <&mmc0_4bit_pins_a
52 vmmc-supply = <®_vddio_sd0>;
57 compatible = "fsl,imx28-mmc";
58 pinctrl-names = "default";
59 pinctrl-0 = <&mmc2_4bit_pins_a
63 vmmc-supply = <®_vddio_sd1>;
68 pinctrl-names = "default";
69 pinctrl-0 = <&hog_pins_a>;
74 MX28_PAD_SSP2_SS0__GPIO_2_19
75 MX28_PAD_PWM4__GPIO_3_29
76 MX28_PAD_AUART2_RX__GPIO_3_8
77 MX28_PAD_ENET0_RX_CLK__GPIO_4_13
79 fsl,drive-strength = <MXS_DRIVE_4mA>;
80 fsl,voltage = <MXS_VOLTAGE_HIGH>;
81 fsl,pull-up = <MXS_PULL_DISABLE>;
84 lcdif_pins_m28: lcdif-m28@0 {
87 MX28_PAD_LCD_VSYNC__LCD_VSYNC
88 MX28_PAD_LCD_HSYNC__LCD_HSYNC
89 MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
90 MX28_PAD_LCD_RESET__LCD_RESET
91 MX28_PAD_LCD_CS__LCD_ENABLE
92 MX28_PAD_AUART1_TX__GPIO_3_5
94 fsl,drive-strength = <MXS_DRIVE_4mA>;
95 fsl,voltage = <MXS_VOLTAGE_HIGH>;
96 fsl,pull-up = <MXS_PULL_DISABLE>;
99 led_pins_gpio: leds-m28@0 {
102 MX28_PAD_SSP3_MISO__GPIO_2_26
103 MX28_PAD_SSP3_SCK__GPIO_2_24
105 fsl,drive-strength = <MXS_DRIVE_4mA>;
106 fsl,voltage = <MXS_VOLTAGE_HIGH>;
107 fsl,pull-up = <MXS_PULL_DISABLE>;
116 pinctrl-names = "default";
117 pinctrl-0 = <&lcdif_24bit_pins_a
119 display = <&display0>;
123 bits-per-pixel = <32>;
127 native-mode = <&timing0>;
129 clock-frequency = <6410256>;
141 pixelclk-active = <1>;
149 duart: serial@80074000 {
150 pinctrl-names = "default";
151 pinctrl-0 = <&duart_pins_b>;
155 usbphy1: usbphy@8007e000 {
159 auart0: serial@8006a000 {
160 pinctrl-names = "default";
161 pinctrl-0 = <&auart0_2pins_a>;
165 auart3: serial@80070000 {
166 pinctrl-names = "default";
167 pinctrl-0 = <&auart3_2pins_b>;
172 pinctrl-names = "default";
173 pinctrl-0 = <&pwm3_pins_a>;
181 vbus-supply = <®_usb1_vbus>;
182 pinctrl-names = "default";
183 pinctrl-0 = <&usb1_pins_a>;
184 disable-over-current;
188 mac0: ethernet@800f0000 {
190 pinctrl-names = "default";
191 pinctrl-0 = <&mac0_pins_a>;
192 phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
193 phy-reset-duration = <100>;
197 mac1: ethernet@800f4000 {
199 pinctrl-names = "default";
200 pinctrl-0 = <&mac1_pins_a>;
206 compatible = "pwm-backlight";
207 pwms = <&pwm 3 5000000>;
208 brightness-levels = <0 4 8 16 32 64 128 255>;
209 default-brightness-level = <6>;
213 compatible = "gpio-leds";
214 pinctrl-names = "default";
215 pinctrl-0 = <&led_pins_gpio>;
219 gpios = <&gpio2 26 0>;
220 linux,default-trigger = "mmc0";
225 gpios = <&gpio2 24 0>;
226 linux,default-trigger = "mmc2";
231 compatible = "simple-bus";
232 #address-cells = <1>;
235 reg_3p3v: regulator@0 {
236 compatible = "regulator-fixed";
238 regulator-name = "3P3V";
239 regulator-min-microvolt = <3300000>;
240 regulator-max-microvolt = <3300000>;
244 reg_vddio_sd0: regulator@1 {
245 compatible = "regulator-fixed";
247 regulator-name = "vddio-sd0";
248 regulator-min-microvolt = <3300000>;
249 regulator-max-microvolt = <3300000>;
250 gpio = <&gpio3 29 0>;
253 reg_vddio_sd1: regulator@2 {
254 compatible = "regulator-fixed";
256 regulator-name = "vddio-sd1";
257 regulator-min-microvolt = <3300000>;
258 regulator-max-microvolt = <3300000>;
259 gpio = <&gpio2 19 0>;
262 reg_usb1_vbus: regulator@3 {
263 compatible = "regulator-fixed";
265 regulator-name = "usb1_vbus";
266 regulator-min-microvolt = <5000000>;
267 regulator-max-microvolt = <5000000>;