sys/gnu/dts/arm/lpc3250-phy3250.dts

   1 /*
   2  * PHYTEC phyCORE-LPC3250 board
   3  *
   4  * Copyright (C) 2015-2019 Vladimir Zapolskiy <vz@mleia.com>
   5  * Copyright 2012 Roland Stigge <stigge@antcom.de>
   6  *
   7  * The code contained herein is licensed under the GNU General Public
   8  * License. You may obtain a copy of the GNU General Public License
   9  * Version 2 or later at the following locations:
  10  *
  11  * http://www.opensource.org/licenses/gpl-license.html
  12  * http://www.gnu.org/copyleft/gpl.html
  13  */
  14
  15 /dts-v1/;
  16 #include "lpc32xx.dtsi"
  17
  18 / {
  19         model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250";
  20         compatible = "phytec,phy3250", "nxp,lpc3250";
  21
  22         memory@80000000 {
  23                 device_type = "memory";
  24                 reg = <0x80000000 0x4000000>;
  25         };
  26
  27         leds {
  28                 compatible = "gpio-leds";
  29
  30                 led0 { /* red */
  31                         gpios = <&gpio 5 1 0>; /* GPO_P3 1, GPIO 80, active high */
  32                         default-state = "off";
  33                 };
  34
  35                 led1 { /* green */
  36                         gpios = <&gpio 5 14 0>; /* GPO_P3 14, GPIO 93, active high */
  37                         linux,default-trigger = "heartbeat";
  38                 };
  39         };
  40
  41         panel: panel {
  42                 compatible = "sharp,lq035q7db03";
  43                 power-supply = <&reg_lcd>;
  44
  45                 port {
  46                         panel_input: endpoint {
  47                                 remote-endpoint = <&cldc_output>;
  48                         };
  49                 };
  50         };
  51
  52         reg_backlight: regulator-backlight {
  53                 compatible = "regulator-fixed";
  54                 regulator-name = "backlight";
  55                 regulator-min-microvolt = <1800000>;
  56                 regulator-max-microvolt = <1800000>;
  57                 gpio = <&gpio 5 4 0>;
  58                 enable-active-high;
  59                 regulator-boot-on;
  60         };
  61
  62         reg_lcd: regulator-lcd {
  63                 compatible = "regulator-fixed";
  64                 regulator-name = "lcd";
  65                 regulator-min-microvolt = <1800000>;
  66                 regulator-max-microvolt = <1800000>;
  67                 gpio = <&gpio 5 0 0>;
  68                 enable-active-high;
  69                 regulator-boot-on;
  70         };
  71
  72         reg_sd: regulator-sd {
  73                 compatible = "regulator-fixed";
  74                 regulator-name = "sd";
  75                 regulator-min-microvolt = <3300000>;
  76                 regulator-max-microvolt = <3300000>;
  77                 gpio = <&gpio 5 5 0>;
  78                 enable-active-high;
  79                 regulator-boot-on;
  80         };
  81 };
  82
  83 &clcd {
  84         max-memory-bandwidth = <18710000>;
  85         status = "okay";
  86
  87         port {
  88                 cldc_output: endpoint {
  89                         remote-endpoint = <&panel_input>;
  90                         arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
  91                 };
  92         };
  93 };
  94
  95 &i2c1 {
  96         clock-frequency = <100000>;
  97
  98         uda1380: uda1380@18 {
  99                 compatible = "nxp,uda1380";
 100                 reg = <0x18>;
 101                 power-gpio = <&gpio 3 10 0>;
 102                 reset-gpio = <&gpio 3 2 0>;
 103                 dac-clk = "wspll";
 104         };
 105
 106         pcf8563: rtc@51 {
 107                 compatible = "nxp,pcf8563";
 108                 reg = <0x51>;
 109         };
 110 };
 111
 112 &i2c2 {
 113         clock-frequency = <100000>;
 114 };
 115
 116 &i2cusb {
 117         clock-frequency = <100000>;
 118
 119         isp1301: usb-transceiver@2c {
 120                 compatible = "nxp,isp1301";
 121                 reg = <0x2c>;
 122         };
 123 };
 124
 125 &key {
 126         keypad,num-rows = <1>;
 127         keypad,num-columns = <1>;
 128         nxp,debounce-delay-ms = <3>;
 129         nxp,scan-delay-ms = <34>;
 130         linux,keymap = <0x00000002>;
 131         status = "okay";
 132 };
 133
 134 &mac {
 135         phy-mode = "rmii";
 136         use-iram;
 137 };
 138
 139 /* Here, choose exactly one from: ohci, usbd */
 140 &ohci /* &usbd */ {
 141         transceiver = <&isp1301>;
 142         status = "okay";
 143 };
 144
 145 &sd {
 146         wp-gpios = <&gpio 3 0 0>;
 147         cd-gpios = <&gpio 3 1 0>;
 148         cd-inverted;
 149         bus-width = <4>;
 150         vmmc-supply = <&reg_sd>;
 151         status = "okay";
 152 };
 153
 154 /* 64MB Flash via SLC NAND controller */
 155 &slc {
 156         status = "okay";
 157
 158         nxp,wdr-clks = <14>;
 159         nxp,wwidth = <40000000>;
 160         nxp,whold = <100000000>;
 161         nxp,wsetup = <100000000>;
 162         nxp,rdr-clks = <14>;
 163         nxp,rwidth = <40000000>;
 164         nxp,rhold = <66666666>;
 165         nxp,rsetup = <100000000>;
 166         nand-on-flash-bbt;
 167         gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
 168
 169         partitions {
 170                 compatible = "fixed-partitions";
 171                 #address-cells = <1>;
 172                 #size-cells = <1>;
 173
 174                 mtd0@0 {
 175                         label = "phy3250-boot";
 176                         reg = <0x00000000 0x00064000>;
 177                         read-only;
 178                 };
 179
 180                 mtd1@64000 {
 181                         label = "phy3250-uboot";
 182                         reg = <0x00064000 0x00190000>;
 183                         read-only;
 184                 };
 185
 186                 mtd2@1f4000 {
 187                         label = "phy3250-ubt-prms";
 188                         reg = <0x001f4000 0x00010000>;
 189                 };
 190
 191                 mtd3@204000 {
 192                         label = "phy3250-kernel";
 193                         reg = <0x00204000 0x00400000>;
 194                 };
 195
 196                 mtd4@604000 {
 197                         label = "phy3250-rootfs";
 198                         reg = <0x00604000 0x039fc000>;
 199                 };
 200         };
 201 };
 202
 203 &ssp0 {
 204         #address-cells = <1>;
 205         #size-cells = <0>;
 206         num-cs = <1>;
 207         cs-gpios = <&gpio 3 5 0>;
 208         status = "okay";
 209
 210         eeprom: at25@0 {
 211                 compatible = "atmel,at25";
 212                 reg = <0>;
 213                 spi-max-frequency = <5000000>;
 214
 215                 pl022,interface = <0>;
 216                 pl022,com-mode = <0>;
 217                 pl022,rx-level-trig = <1>;
 218                 pl022,tx-level-trig = <1>;
 219                 pl022,ctrl-len = <11>;
 220                 pl022,wait-state = <0>;
 221                 pl022,duplex = <0>;
 222
 223                 at25,byte-len = <0x8000>;
 224                 at25,addr-mode = <2>;
 225                 at25,page-size = <64>;
 226         };
 227 };
 228
 229 &tsc {
 230         status = "okay";
 231 };
 232
 233 &uart2 {
 234         status = "okay";
 235 };
 236
 237 &uart3 {
 238         status = "okay";
 239 };
 240
 241 &uart5 {
 242         status = "okay";
 243 };