2 # This file adds to the values in AR91XX_BASE.hints.
7 hint.argemdio.0.at="nexus0"
8 hint.argemdio.0.maddr=0x1a000000
9 hint.argemdio.0.msize=0x1000
10 hint.argemdio.0.order=0
12 # Embedded Atheros Switch
13 hint.arswitch.0.at="mdio0"
14 hint.arswitch.0.is_7240=1
15 hint.arswitch.0.numphys=4
16 hint.arswitch.0.phy4cpu=1 # phy 4 is a "CPU" separate PHY
17 hint.arswitch.0.is_rgmii=0
18 hint.arswitch.0.is_gmii=1 # arge1 <-> switch PHY is GMII
20 # arge0 - MII, autoneg, phy(4)
21 hint.arge.0.phymask=0x10 # PHY4
22 hint.arge.0.mdio=mdioproxy1 # .. off of the switch mdiobus
24 # arge1 - GMII, 1000/full
25 hint.arge.1.phymask=0x0 # No directly mapped PHYs
26 hint.arge.1.media=1000
29 # The AP121 4MB flash layout:
31 # bootargs=console=ttyS0,115200 root=31:02 rootfstype=squashfs
32 # init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),
33 # 2752k(rootfs),896k(uImage),64k(NVRAM),64k(ART)
43 hint.map.0.at="flash/spi0"
44 hint.map.0.start=0x00000000
45 hint.map.0.end=0x000040000
46 hint.map.0.name="uboot"
49 hint.map.1.at="flash/spi0"
50 hint.map.1.start=0x00040000
51 hint.map.1.end=0x00050000
52 hint.map.1.name="uboot-env"
55 hint.map.2.at="flash/spi0"
56 hint.map.2.start=0x00050000
57 hint.map.2.end=0x00300000
58 hint.map.2.name="rootfs"
61 hint.map.3.at="flash/spi0"
62 hint.map.3.start=0x00300000
63 hint.map.3.end=0x003e0000
64 hint.map.3.name="kernel"
67 hint.map.4.at="flash/spi0"
68 hint.map.4.start=0x003e0000
69 hint.map.4.end=0x003f0000
73 # This is radio calibration section. It is (or should be!) unique
74 # for each board, to take into account thermal and electrical differences
75 # as well as the regulatory compliance data.
77 hint.map.5.at="flash/spi0"
78 hint.map.5.start=0x003f0000
79 hint.map.5.end=0x00400000
83 # GPIO specific configuration block
85 # Don't flip on anything that isn't already enabled.
86 # This includes leaving the SPI CS1/CS2 pins as GPIO pins as they're
88 hint.gpio.0.function_set=0x00000000
89 hint.gpio.0.function_clear=0x00000000
91 # These are the GPIO LEDs and buttons which can be software controlled.
92 #hint.gpio.0.pinmask=0x001c02ae
93 hint.gpio.0.pinmask=0x00001803
97 # gpio11 - Jumpstart button
98 # gpio12 - Reset button
100 # LEDs are configured separately and driven by the LED device
101 hint.gpioled.0.at="gpiobus0"
102 hint.gpioled.0.name="wlan"
103 hint.gpioled.0.pins=0x0001
105 hint.gpioled.1.at="gpiobus0"
106 hint.gpioled.1.name="usb"
107 hint.gpioled.1.pins=0x0002