1 .\" Copyright (c) 1999 Robert Nordier
2 .\" All rights reserved.
4 .\" Redistribution and use in source and binary forms, with or without
5 .\" modification, are permitted provided that the following conditions
7 .\" 1. Redistributions of source code must retain the above copyright
8 .\" notice, this list of conditions and the following disclaimer.
9 .\" 2. Redistributions in binary form must reproduce the above copyright
10 .\" notice, this list of conditions and the following disclaimer in the
11 .\" documentation and/or other materials provided with the distribution.
13 .\" THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS``AS IS'' AND
14 .\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
15 .\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
16 .\" PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS
17 .\" BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
18 .\" OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT
19 .\" OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
20 .\" BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
21 .\" WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
22 .\" OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
23 .\" EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
32 .Nd boot manager installation/configuration utility
38 .Op Fl e Ar bell character
50 boot manager permits the operator to select from which disk and
51 slice an i386 machine (PC) is booted.
53 Note that what are referred to here as
59 documentation relating to the PC.
60 Typically, only non-removable disks are sliced.
64 utility optionally installs the
66 boot manager on the specified
68 and allows various operational parameters to be configured.
70 On PCs, a boot manager typically occupies sector 0 of a disk, which is
71 known as the Master Boot Record (MBR).
72 The MBR contains both code (to which control is passed by the PC BIOS)
73 and data (an embedded table of defined slices).
76 .Bl -tag -width indent
81 This option causes MBR code to be replaced, without
82 affecting the embedded slice table.
89 which will use the video card as output, alternatively
91 can be used for output to the COM1 port.
92 (Be aware that nothing will be output to the COM1 port unless the
93 modem signals DSR and CTS are active.)
95 Specify the drive number used by the PC BIOS in referencing the drive
96 which contains the specified
98 Typically this will be 0x80 for the first hard drive, 0x81 for the
99 second hard drive, and so on; however any integer between 0 and 0xff
101 .It Fl e Ar bell character
102 Set the character to be printed in case of input error.
104 Specify that a backup copy of the preexisting MBR should be written to
106 This file is created if it does not exist, and replaced if it does.
107 .It Fl i Ar volume-id
108 Specifies a volume-id (in the form XXXX-XXXX) to be saved at location
109 0x1b8 in the MBR. This information is sometimes used by NT, XP and Vista
110 to identify the disk drive. The option is only compatible with version 2.00
111 of the 512-byte boot block.
113 Specify slices to be enabled/disabled, where
115 is an integer between 0 (no slices enabled) and 0xf (all four slices
117 Each mask bit enables corresponding slice if set to 1.
118 The least significant bit of the mask corresponds to slice 1,
119 the most significant bit of the mask corresponds to slice 4.
121 A comma-separated string of any of the following options may be
124 prepended as necessary):
125 .Bl -tag -width indent
127 Use the disk packet (BIOS INT 0x13 extensions) interface,
128 as opposed to the legacy (CHS) interface, when doing disk I/O.
129 This allows booting above cylinder 1023, but requires specific
134 Forces the drive containing the disk to be referenced using drive
135 number definable by means of the -d option.
139 Allow the MBR to be updated by the boot manager.
140 (The MBR may be updated to flag slices as
142 and to save slice selection information.)
143 This is the default; a
145 option causes the MBR to be treated as read-only.
148 Set the default boot selection to
150 Values between 1 and 4 refer to slices; a value of 5 refers to the
151 option of booting from a second disk.
154 or a value of 6 can be used to boot via PXE.
156 Set the timeout value to
158 (There are approximately 18.2 ticks per second.)
160 Verbose: display information about the slices defined, etc.
163 .Bl -tag -width /boot/boot0sio -compact
168 .It Pa /boot/boot0sio
169 Image for serial consoles (COM1,9600,8,N,1,MODEM)
174 To boot slice 2 on the next boot:
176 .Dl "boot0cfg -s 2 ada0"
178 To enable just slices 1 and 3 in the menu:
180 .Dl "boot0cfg -m 0x5 ada0"
182 To go back to non-interactive booting, use
184 to install the default MBR:
193 .An Robert Nordier Aq rnordier@FreeBSD.org .
199 to fail, depending on the nature of BIOS support.
203 option with an incorrect -d operand may cause the boot0 code
204 to write the MBR to the wrong disk, thus trashing its previous