net80211: drop m_pullup call from ieee80211_crypto_decap.
For most wireless drivers Rx mbuf is allocated as one
contiguous chunk; only few are using chains for allocations -
but even then at least MCLBYTES (minus Rx descriptor size) is
available in the first mbuf.
In addition to the above, m_pullup was never called here - otherwise,
reallocation will break post-crypto_decap logic (ieee80211_decap,
ieee80211_deliver_data...), so just remove it; length check is left
in case if some truncated frame appears here.
Justin Hibbits [Sat, 19 Jan 2019 05:20:31 +0000 (05:20 +0000)]
dpaa: fix 32-bit build
Book-E powerpc uses 64-bit vm_paddr_t, and 32-bit powerpc has 32-bit pointers,
so gcc errors with cast to pointer from integer of different size. As this will
not actually be used in reality anyway, simply quiet the warning by casting
through uintptr_t.
Justin Hibbits [Sat, 19 Jan 2019 04:54:12 +0000 (04:54 +0000)]
powerpc/dpaa: Handle DMAP virtual addresses in DPAA
sendfile(2) appears to now use DMAP wherever possible. These addresses are not
managed by pmap, so pmap_kextract() returns a 0 physical address, causing
failure.
Justin Hibbits [Sat, 19 Jan 2019 04:47:19 +0000 (04:47 +0000)]
powerpc: Fix opaque irq data initialization
The powerpc_intr structure is not zero-initialized, so on an invariants
build would panic in the xics driver with an invalid pointer. Also fix the
xics driver to share the private data setup code between xics_enable() and
xics_bind().
Conrad Meyer [Fri, 18 Jan 2019 23:54:51 +0000 (23:54 +0000)]
vmm(4): Mask Spectre feature bits on AMD hosts
For parity with Intel hosts, which already mask out the CPUID feature
bits that indicate the presence of the SPEC_CTRL MSR, do the same on
AMD.
Eventually we may want to have a better support story for guests, but
for now, limit the damage of incorrectly indicating an MSR we do not yet
support.
Eventually, we may want a generic CPUID override system for
administrators, or for minimum supported feature set in heterogenous
environments with failover. That is a much larger scope effort than
this bug fix.
Justin Hibbits [Fri, 18 Jan 2019 23:26:31 +0000 (23:26 +0000)]
Fix top(1) long options handling
getopt_long(3) requires the long options be terminated by a NULL block.
Without the terminator, an invalid long option results in a segmentation
fault.
libinput has special handling for Lenovo ThinkPad *40 series, where it
treats clicks on the top button area as if they came from the TrackPoint:
https://wayland.freedesktop.org/libinput/doc/latest/t440-support.html
Detect these devices and set the corresponding evdev property.
Brooks Davis [Fri, 18 Jan 2019 21:46:38 +0000 (21:46 +0000)]
Make SIFTR work again after r342125 (D18443).
Correct a logic error.
Only disable when already enabled or enable when disabled.
Submitted by: Richard Scheffenegger
Reviewed by: Cheng Cui
Obtained from: Cheng Cui
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D18885
Dimitry Andric [Fri, 18 Jan 2019 20:35:24 +0000 (20:35 +0000)]
Remove leading slash from OLD_DIRS assignment in ObsoleteFiles.inc. The
"make delete-old" mechanism will already take care of such prefixes, and
this prevents a double leading slash from being displayed.
If i386 has more than 4G of memory, allow the same number of busdma
bounce pages as for amd64. In fact, in this case bouncing sometimes
is much heavier than on amd64.
Reviewed by: markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D18854
x86 busdma: fix mis-use of bus_addr_t where vm_paddr_t is assumed.
Right now bus_addr_t and vm_paddr_t are always aliased to the same
underlying integer type on x86, which makes the interchange hard to
detect. Shortly, i386 kernel would use uint64_t for vm_paddr_t to
enable automatic use of PAE paging structures if hardware allows it,
while bus_addr_t would be extended to 64bit only when PAE option is
specified.
Fix all places that were identified as using bus_addr_t while page
address was assumed. This was performed by testing the complete PAE
merging patch on machine with > 4G of RAM enabled.
Reviewed by: markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D18854
MI VM: Make it possible to set size of superpage at boot instead of compile time.
In order to allow single kernel to use PAE pagetables on i386 if
hardware supports it, and fall back to classic two-level paging
structures if not, superpage code should be able to adopt to either 2M
or 4M superpages size. There I make MI VM structures large enough to
track the biggest possible superpage, by allowing architecture to
define VM_NFREEORDER_MAX and VM_LEVEL_0_ORDER_MAX constants.
Corresponding VM_NFREEORDER and VM_LEVEL_0_ORDER symbols can be
defined as runtime values and must be less than the _MAX constants.
If architecture does not define _MAXs, it is assumed that _MAX ==
normal constant.
Reviewed by: markj
Tested by: pho (as part of the larger patch)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D18853
The NVDIMM root device is parent to the individual ACPI NVDIMM
devices. Add a driver for the NVDIMM root device that can own
enumeration of NVDIMM devices as well as NVDIMM SPA ranges that the
system has.
Submitted by: D Scott Phillips <d.scott.phillips@intel.com>
Sponsored by: Intel Corporation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D18346
Conrad Meyer [Thu, 17 Jan 2019 23:21:02 +0000 (23:21 +0000)]
ioat(4): Set __result_use_check on ioat_acquire_reserve
Even M_WAITOK callers must check for failure. For example, if the device is
quiescing, either due to automatic error-recovery induced reset, or due to
administrative detach, the routine will return ENXIO and the acquire
reference will not be held. So, there is no mode in which it is safe to
assume the routine succeeds without checking.
Conrad Meyer [Thu, 17 Jan 2019 19:44:47 +0000 (19:44 +0000)]
Add definitions for AMD Spectre/Meltdown CPUID information
No functional change, aside from printing recognized bits in CPU
identification.
The bits are documented in 111006-B "Indirect Branch Control Extension"[1] and
124441 "Speculative Store Bypass Disable."[2]
Notably missing (left as future work):
* Integration with hw.spec_store_bypass_disable and hw_ssb_active flag,
which are currently Intel-specific
* Integration with hw_ibrs_active global flag, which are currently
Intel-specific
* SSB_NO integration in hw_ssb_recalculate()
* Bhyve integration (PR 235010)
Kyle Evans [Thu, 17 Jan 2019 18:51:56 +0000 (18:51 +0000)]
Revert r343095
This was intended to fix the soft reset timeout on boot for OrangePi One/R1
with internal PHY, but seems to cause other problems later on due to soft
resetting around some state changes that may or may not make the NIC
non-functional.
Reverting this for now while a better solution is sought out.
Eugene Grosbein [Thu, 17 Jan 2019 18:07:59 +0000 (18:07 +0000)]
Re-add new small tool trim(8) to delete contents for blocks
on devices using wear-leveling algorithms as a few weeks passed
after review and discussion of trim(8) ceased and
we still have no utility to perform the job.
Mark Johnston [Thu, 17 Jan 2019 17:36:18 +0000 (17:36 +0000)]
Fix handling of rights on stdio streams.
- Limit rights on stdio before opening input files. Otherwise, open()
may return one of the standard descriptors and we end up limiting
rights such that we cannot read from one of the input files.
- Use caph_limit_stdio(), which suppresses EBADF, to ensure that
we don't emit an error if one of the stdio streams is closed.
- Don't bother further limiting rights on stdin when stdin isn't going
to be used. Doing so correctly requires checking for a number of
edge cases, and it doesn't provide any significant benefit.
PR: 234885
Reviewed by: oshogbo
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D18860
Eugene Grosbein [Thu, 17 Jan 2019 14:09:55 +0000 (14:09 +0000)]
jail(8): stop crashing with SIGSEGV inside run_command() function
while processing not entirely correct jail.conf(5) file
having something like "ip4.addr = 127.0.0.1;" and no "ip4 = ...;"
so extrap variable stays NULL.
Kirk McKusick [Thu, 17 Jan 2019 06:35:45 +0000 (06:35 +0000)]
Create new EINTEGRITY error with message "Integrity check failed".
An integrity check such as a check-hash or a cross-correlation failed.
The integrity error falls between EINVAL that identifies errors in
parameters to a system call and EIO that identifies errors with the
underlying storage media. EINTEGRITY is typically raised by intermediate
kernel layers such as a filesystem or an in-kernel GEOM subsystem when
they detect inconsistencies. Uses include allowing the mount(8) command
to return a different exit value to automate the running of fsck(8)
during a system boot.
These changes make no use of the new error, they just add it. Later
commits will be made for the use of the new error number and it will
be added to additional manual pages as appropriate.
Fix conditional obsolete files entry for WITHOUT_EXAMPLES
Add all the files under /usr/share/examples to the MK_EXAMPLES
section. OLD_DIRS entries are not removed if they're not empty so
prior to this change WITHOUT_EXAMPLES didn't have significant effect
on the updated system.
Add optional obsolete files for the installworld without sendmail
Add two more entries for WITHOUT_SENDMAIL install. The /var/spool/clientmqueue
entry would be deleted only if there are no files/dirs in it, so the
content generated during previous lifecycle of the system is safe
Jilles Tjoelker [Wed, 16 Jan 2019 21:59:18 +0000 (21:59 +0000)]
libedit: Avoid out of bounds read in 'bind' command
This is CVS revision 1.31 from NetBSD lib/libedit/chartype.c:
Make sure that argv is NULL terminated since functions like tty_stty rely
on it to be so (Gerry Swinslow)
This broke when the wide-character support was enabled in libedit. The
conversion from multibyte to wide-character did not supply the apparently
expected terminating NULL in the new argv array.
Add parentheses to perform assignment before comparison. The prior
condition worked because fdt_parent_addr_cells returns 1 for the DTB
on which fdt_fixup_ranges is called and accidentally par_addr_cells
ends up to be set to the same value.
Kyle Evans [Wed, 16 Jan 2019 14:42:33 +0000 (14:42 +0000)]
awg: Move MAC soft reset to awg_init_locked to avoid soft reset timeout
From NetBSD: Since the MAC can get stuck in reset state with no link, ignore
reset timeouts and continue with initializing the device.
Fixes "soft reset timeout" issue at boot with no network cable plugged in.
awg_init may be called multiple times throughout normal interface usage, so
the tx/rx descriptor base address registers must be written after each MAC
reset and are moved as such.
This problem has been observed on FreeBSD, H3/H2+ devices with an internal
PHY (includes OrangePi R1, OrangePi One at least).
Generic Tx stats fixes:
- do not try to parse "aggregation status" for single frames; send them
to iwn_tx_done() instead;
- try to attach mbuf / node reference pair to reported BA events;
allows to fix reported status for ieee80211_tx_complete() and ifnet counters
(previously all A-MPDU frames were counted as failed - see PR 210211);
requires few more firmware bug workarounds;
- preserve short / long retry counters for wlan_amrr(4)
(disabled for now - causes significant performance degradation).
- Add new IWN_DEBUG_AMPDU debug category.
- Add one more check into iwn_tx_data() to prevent aggregation ring
overflow.
- Workaround 'seqno % 256' != 'current Tx slot' case (until D9195 is not
in the tree).
- Improve watchdog timer updates (previously watchdog check was omitted
when at least one frame was transmitted).
- Stop Tx when memory leak in currently used ring was detected (unlikely
to happen).
- Few other minor fixes.
Was previously tested with:
- Intel 6205, STA mode (Tx aggregation behaves much better now).
- Intel 4965AGN, STA mode (still unstable).
rtwn(4): clear 'basic' rate bit before calculating RTS/CTS rate.
Rate tables have this bit set to indicate minimal set of basic rates;
however, it overlappes with MCS bit, so rate2ridx() will treat them as
an 11n rate.
Due to the current rates setup the issue can be reproduced only
in 5GHz band with 11n / protection enabled.
- Specify BUS_DMA_NOWAIT for bus_dmamap_load() on rx refill, since
callbacks are not supposed to be used.
- Match tso/non-tso tags to corresponding tx map operations. Create
separate tso maps for tx descriptors. In particular, do not use
non-tso tag to load, unload, or destroy a map created with tso tag.
- Add missed bus_dmamap_sync() calls.
Submitted by: marius.
Reported and tested by: pho
Reviewed by: marius
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Justin Hibbits [Wed, 16 Jan 2019 03:52:43 +0000 (03:52 +0000)]
powerpc: Fix FPU fsqrt emulation special case results
If fsqrts is emulated with +INF as its argument, the 0 return value causes a
NULL pointer dereference, panicking the system. Follow the PowerISA and
return +INF with no FP exception.
Conrad Meyer [Wed, 16 Jan 2019 02:19:04 +0000 (02:19 +0000)]
vmm(4): Take steps towards multicore bhyve AMD support
vmm's CPUID emulation presented Intel topology information to the guest, but
disabled AMD topology information and in some cases passed through garbage.
I.e., CPUID leaves 0x8000_001[de] were passed through to the guest, but
guest CPUs can migrate between host threads, so the information presented
was not consistent. This could easily be observed with 'cpucontrol -i 0xfoo
/dev/cpuctl0'.
Slightly improve this situation by enabling the AMD topology feature flag
and presenting at least the CPUID fields used by FreeBSD itself to probe
topology on more modern AMD64 hardware (Family 15h+). Older stuff is
probably less interesting. I have not been able to empirically confirm it
is sufficient, but it should not regress anything either.
Marcin Wojtas [Wed, 16 Jan 2019 02:13:21 +0000 (02:13 +0000)]
Suppress excessive error prints in ENA TX hotpath
In FreeBSD, this is normal situation that the Tx ring is being full. In
hat case, the packet is put back into drbr and the next attempt to send
it is taken after the cleanup.
Too much logs like this can cause system instability and even cause the
device reset (because keep alive or cleanup could be missed).
To fix that, the log level of this message is changed to debug.
Upon this change upgrade the driver version to v0.8.2.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
Marcin Wojtas [Wed, 16 Jan 2019 01:54:04 +0000 (01:54 +0000)]
Suppress excessive print in ENA HAL
In FreeBSD, this is normal situation that the Tx ring is being full. In
that case, the packet is put back into drbr and the next attempt to send
it is taken after the cleanup.
Too much logs like this can cause system instability and even cause the
device reset (because keep alive or cleanup could be missed).
To fix that, the log level of this message is changed to debug.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
[rpi] Reorganize spigen(4) overlays for Raspberry Pi
- Remove CS=2 entry from spigen-rpi2 since it didn't work
- Add spigen-rpi3 overlay for Raspberry Pi 3
- Enable rpi overlay modules for GENERIC kernel on aarch64
Marcelo Araujo [Wed, 16 Jan 2019 00:39:23 +0000 (00:39 +0000)]
Use capsicum_helpers(3) that allow us to simplify the code and its functions
will return success when the kernel is built without support of
the capability mode.
It is important to note, that I'm taking a more conservative approach
with these changes and it will be done in small steps.
Bjoern A. Zeeb [Tue, 15 Jan 2019 22:31:54 +0000 (22:31 +0000)]
With the sync from Dragonfly BSD in r318216 a bug slipped in (also still present
upstream it seems).
The tlv variable was changed to a pointer but the advancement of the data pointer
was left as sizeof(tlv). While the sizeof the (now) pointer equals the
sizeof 2 x uint32_t (size of the struct) on 64bit platforms, on 32bit platforms
the size of the advancement of the data pointer was wrong leading to
firmware load issues.
Correctly advance the data pointer by the size of the structure and not by
the size of a pointer.
Gleb Smirnoff [Tue, 15 Jan 2019 19:33:47 +0000 (19:33 +0000)]
Fix compilation failures on different arches that have vm_machdep.c not
aware of counter_u64_t by including counter.h into uma_int.h. I'm not
happy about this inclusion, but it fixes compilation ASAP.
John Baldwin [Tue, 15 Jan 2019 18:53:45 +0000 (18:53 +0000)]
Reject new sessions if the necessary queues aren't initialized.
ccr reuses the control queue and first rx queue from the first port on
each adapter. The driver cannot send requests until those queues are
initialized. Refuse to create sessions for now if the queues aren't
ready. This is a workaround until cxgbe allocates one or more
dedicated queues for ccr.
Gleb Smirnoff [Tue, 15 Jan 2019 18:32:26 +0000 (18:32 +0000)]
Only do uz_items accounting for zones that have a limit set in uz_max_items.
This reduces amount of locking required for these zones.
Also, for cache only zones (UMA_ZFLAG_CACHE) accounting uz_items wasn't
correct at all, since they may allocate items directly from their backing
store and then free them via UMA underflowing uz_items.
John Baldwin [Tue, 15 Jan 2019 18:20:20 +0000 (18:20 +0000)]
Update the note about the need for COMPAT_FREEBSD<n> kernel options.
Rather than mentioning the requirement for 4.x binaries but not
explaining why (it was assuming an upgrade from 4.x to 5.0-current),
explain when compat options are needed (for running existing host
binaries) in a more general way while using a more modern example
(COMPAT_FREEBSD11 for 11.x binaries). While here, explicitly mention
that a GENERIC kernel should always work.
Stephen Hurd [Tue, 15 Jan 2019 17:40:19 +0000 (17:40 +0000)]
Fix window update issue when scaling disabled
When the TCP window scale option is not used, and the window
opens up enough in one soreceive, a window update will not be sent.
For example, if recwin == 65535, so->so_rcv.sb_hiwat >= 262144, and
so->so_rcv.sb_hiwat <= 524272, the window update will never be sent.
This is because recwin and adv are clamped to TCP_MAXWIN << tp->rcv_scale,
and so will never be >= so->so_rcv.sb_hiwat / 4
or <= so->so_rcv.sb_hiwat / 8.
This patch ensures a window update is sent if the window opens by
TCP_MAXWIN << tp->rcv_scale, which should only happen when the window
size goes from zero to the max expressible.
This issue looks like it was introduced in r306769 when recwin was clamped
to TCP_MAXWIN << tp->rcv_scale.
Andrew Turner [Tue, 15 Jan 2019 09:48:18 +0000 (09:48 +0000)]
Ensure the I-Cache is correctly handled in arm64_icache_sync_range
The cache_handle_range macro to handle the arm64 instruction and data
cache operations would return when it was complete. This causes problems
for arm64_icache_sync_range and arm64_icache_sync_range_checked as they
assume they can execute the i-cache handling instruction after it has been
called.
Fix this by making this assumption correct.
While here add missing instruction barriers and adjust the style to
match the rest of the assembly.