Pyun YongHyeon [Tue, 12 Jun 2007 02:16:02 +0000 (02:16 +0000)]
Bring overhauled nfe(4) into tree.
o s/printf/device_printf/g
o Nuke OpenBSDism.
o Nuke NetBSD/OpenBSD specific DMA sync operations.(we don't have a way
to sync a single descriptor within a DMA map.)
o Remove recursive mutex.
o bus_dma(9) clean up.
o 40bit DMA address support.
o Add protection for Rx map load failure.
o Fix a long standing bug for watchdog timeout. [1]
o Add additional protections, missing Tx completion interrupt, losing
start Tx command, for watchdog timeout.
o Switch to taskqueue(9) API to handle interrupts.
o Use our own timer for watchdog instead of if_watchdog/if_timer
interface.
o Advertise VLAN header length/capability correctly to upper layer.
o Remove excessive kernel stack consumption in nfe_encap().
o Handle highly fragmented mbuf chains correctly.
o Enable etherenet address reprogramming with ifconfig(8).
o Add ALTQ/TSO, MSI/MSIX support.
o Increased Rx ring to 256 descriptors from 128.
o Align Tx/Rx descriptor ring on sizeof(struct nfe_desc64) boundary.
o Remove alignment restrictions on Tx/Rx buffers.
o Rewritten jumbo frame support code.
o Add support for hardware assistend VLAN tag insertion/stripping.
o Add support for Tx/Rx flow control based on patches from Peer Chen. [2]
o Add a routine that detects whether ethernet address swap routines is
required. [3]
o Add a workaround that take MAC/PHY out of power down mode.
o Add suspend/resume support.
o style(9) and code clean up.
Special thanks to Shigeaki Tagashira, the original porter of nfe(4),
who submitted lots of patches, performed uncountable number of
regression tests and maintained nfe(4) for a long time. Without his
enthusiastic help and support I could never have completed this
overhauling task.
The only weak point of nfe(4) compared to nve(4) is instability of
manual half-duplex media selection on certain hardwares(auto sensing
media type should work for all cases, though). This was a long
standing bug of nfe(4) and I still have no idea why it doesn't work
on some hardwares.
Obtained from: OpenBSD [1]
Submitted by: Peer Chen < pchen at nvidia dot com > [2], [3]
Reviewed by: Shigeaki Tagashira < shigeaki AT se DOT hiroshima-u DOT ac DOT jp >
Tested by: Shigeaki Tagashira, current
Discussed with: current
Silence from: obrien
Robert Watson [Tue, 12 Jun 2007 00:12:01 +0000 (00:12 +0000)]
Eliminate now-unused SUSER_ALLOWJAIL arguments to priv_check_cred(); in
some cases, move to priv_check() if it was an operation on a thread and
no other flags were present.
Eliminate caller-side jail exception checking (also now-unused); jail
privilege exception code now goes solely in kern_jail.c.
We can't yet eliminate suser() due to some cases in the KAME code where
a privilege check is performed and then used in many different deferred
paths. Do, however, move those prototypes to priv.h.
Olivier Houchard [Mon, 11 Jun 2007 19:38:38 +0000 (19:38 +0000)]
Exclude inet_addr.c from the build.
It only provides inet_aton(), which is already provided by the libc. This
causes multiple symbol definitions when linking statically.
Andrew Gallatin [Mon, 11 Jun 2007 18:45:49 +0000 (18:45 +0000)]
Move the oversize ethernet frame size check into DIAGNOSTIC,
as was proposed when it was originally added. This allows
LRO to work on non-DIAGNOSTIC kernels without consuming
any mbuf flags.
Ceri Davies [Mon, 11 Jun 2007 18:36:39 +0000 (18:36 +0000)]
Create group ftp by default. This is gid 14 as this is the historical
id used by sysinstall when enabling anonymous FTP.
Change the default group used by sysinstall for setting up anonymous FTP
from operator to ftp; there is no reason to use operator and there are
potential security issues when doing so.
PR: 93284
Approved by: ru (mentor)
Reviewed by: simon
Andrew Gallatin [Mon, 11 Jun 2007 14:01:10 +0000 (14:01 +0000)]
Small LRO related fixes for mxge:
- Allow LRO to be enabled / disabled at runtime
- Fix a double-free at module unload time.
- Only update timestamp in lro merge when it is present in the frame
Sponsored by: Myricom
Bruce Evans [Mon, 11 Jun 2007 13:02:15 +0000 (13:02 +0000)]
When we return from a "show" function without printing anything except
a warning, return 1 instead of 0 to indicate that we didn't print
anything, so that top-level callers don't print a spurious newline.
This is mainly to fix output formatting when stderr is redirected. It
also helps in some cases when stderr is interleaved with stdout,
depending on the details of the interleaving (this program has the
usual null explicit support for syncing stderr with stdout).
Return 1 instead of -1 after printing the "malloc failed" warning, since
the return value is boolean.
Andrew Thompson [Mon, 11 Jun 2007 10:56:06 +0000 (10:56 +0000)]
MFp4 (missed in net80211 megaupdate)
- Use a seperate taskqueue+thread for reset tasks since iwi_ops will
block.
- Return from iwi_ops if the interface has been downed
- The firmware will fail if we are already associated
- Add myself to the copyright
Fix what seems to be a copy-paste buglet (`moused_type' is used
in the description of `moused_flags', instead of the later), and
add a description of `moused_XXX_flags' where `XXX' is the port
name of a non-default moused invocation -- including an example
of using "-3" with the default moused(8) instance, but no special
flags for moused(8) invocations handling 3-button USB mice (which
seems a very common scenario these days).
Bruce Evans [Mon, 11 Jun 2007 07:48:52 +0000 (07:48 +0000)]
Fix an aliasing bug which was finally detected by gcc-4.2. fdlibm has
hundreds of similar aliasing bugs, but all except this one seem to have
been fixed by Cygnus and/or NetBSD before the modified version of fdlibm
was imported into FreeBSD in 1994.
PR: standards/113147
Submitted by: Steve Kargl <sgk@troutmask.apl.washington.edu>
Sam Leffler [Mon, 11 Jun 2007 03:56:33 +0000 (03:56 +0000)]
Update for revised 802.11 support:
o revised channel handling support; ifconfig now queries the kernel to
find the list of available channels and handles channel promotion;
channel attributes can be specified as part of the channel; e.g. 36:a
for channel 36 in 11a (as opposed to turbo A or HT A)
o use channel list to map between freq and IEEE channel #; this eliminates
all knowledge of how the mapping is done and fixes handling of cases
where channels overlap in the IEEE channel # space but are distinct in
the frequency+attributes space (e.g. PSB)
o add new knobs: bgscan, ff (Atheors fast frames), dturbo (Atheros
Dynamic Turbo mode), bgscanidle, bgscanintvl, scanvalid, roam:rssi11a,
roam:rssi11b, roam:rssi11g, roam:rate11a, roam:rate11b, roam:rate11g
(roaming parameters), burst, doth (forthcoming 11h support)
o print contents of WME, ATH, WPA, RSN, information elements with -v option
o print signal strength in dBm
o print noise floor in dBm
o add list txpow to print tx power caps/channel
o change default channel display in status to be more informative
Sam Leffler [Mon, 11 Jun 2007 03:36:55 +0000 (03:36 +0000)]
Update 802.11 wireless support:
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
Pyun YongHyeon [Mon, 11 Jun 2007 02:00:50 +0000 (02:00 +0000)]
Increase a maximum segment size of DMA to 4096. Previously it used
MCLBYTES for the segment size but it used too many Tx descriptors in
TSO case.
While I'm here adjust maximum size of the sum of all segment lengths
in a given DMA mapping to 65535, the maximum size, in bytes, of a IP
packet.
Pyun YongHyeon [Mon, 11 Jun 2007 01:55:09 +0000 (01:55 +0000)]
Disable automatic IP ID increment. Due to a hardware bug the automatic
IP ID increment in TSO case generated corrupted IP packets.
This change brings back TSO capability.
Ariff Abdullah [Mon, 11 Jun 2007 00:49:46 +0000 (00:49 +0000)]
Filter/compress the amount of channel trigger. This should reduce
much of lock/unlock contentions within the interrupt handler. Most
of these drivers only need PCMTRIG_START or STOP (ABORT).
Marcel Moolenaar [Mon, 11 Jun 2007 00:38:06 +0000 (00:38 +0000)]
Use default options for default partitioning schemes, rather than
making the relevant files standard. This avoids duplication and
makes it easier to override/disable unwanted schemes. Since ARM
doesn't have a DEFAULTS configuration file, leave the source
files for the BSD and MBR partitioning schemes in files.arm for
now.
Attilio Rao [Sun, 10 Jun 2007 21:59:14 +0000 (21:59 +0000)]
Optimize vmmeter locking.
In particular:
- Add an explicative table for locking of struct vmmeter members
- Apply new rules for some of those members
- Remove some unuseful comments
Heavily reviewed by: alc, bde, jeff
Approved by: jeff (mentor)
Andre Oppermann [Sun, 10 Jun 2007 21:07:21 +0000 (21:07 +0000)]
Fix a case in tcp_do_segment() where tcp_update_sack_list() would
be called with an incorrect segment end value. tcp_reass() may
trim segments when they overlap with already existing ones in the
reassembly queue. Instead of saving the segment end value before
the call to tcp_reass() compute it on the fly based on the effective
segment length afterwards.
This bug was not really problematic as no information got lost and
the eventual SACK information computation was correct nontheless.
David Malone [Sun, 10 Jun 2007 19:13:40 +0000 (19:13 +0000)]
Some style improvements suggested by bde, including removing an
unused include, adding parens for return and sizeof and renaming,
adding some missing whitespace and sorting some variables.
el.c 1.42, term.c 1.46, term.h 1.18, editline.3 1.52, histedit.h 1.29:
# - Add more readline functions, enough for gdb-6.5
# - Make el_get varyadic, and implement EL_GETTC.
# - XXX: the EL_SETTC api will change in the future.
Note: The latter change breaks the ABI of the el_get() function.
Yaroslav Tykhiy [Sun, 10 Jun 2007 18:57:20 +0000 (18:57 +0000)]
Now pam_nologin(8) will provide an account management function
instead of an authentication function. There are a design reason
and a practical reason for that. First, the module belongs in
account management because it checks availability of the account
and does no authentication. Second, there are existing and potential
PAM consumers that skip PAM authentication for good or for bad.
E.g., sshd(8) just prefers internal routines for public key auth;
OTOH, cron(8) and atrun(8) do implicit authentication when running
a job on behalf of its owner, so their inability to use PAM auth
is fundamental, but they can benefit from PAM account management.
Document this change in the manpage.
Modify /etc/pam.d files accordingly, so that pam_nologin.so is listed
under the "account" function class.
Bump __FreeBSD_version (mostly for ports, as this change should be
invisible to C code outside pam_nologin.)
Marcel Moolenaar [Sun, 10 Jun 2007 16:53:01 +0000 (16:53 +0000)]
Work around a firmware bug in the HP rx2660, where in ACPI an I/O port
is really a memory mapped I/O address. The bug is in the GAS that
describes the address and in particular the SpaceId field. The field
should not say the address is an I/O port when it clearly is not.
With an additional check for the IA64_BUS_SPACE_IO case in the bus
access functions, and the fact that I/O ports pretty much not used
in general on ia64, make the calculation of the I/O port address a
function. This avoids inlining the work-around into every driver,
and also helps reduce overall code bloat.
Matt Jacob [Sun, 10 Jun 2007 01:43:11 +0000 (01:43 +0000)]
Initialized ets to zero. This is arguably a gcc bug in that ets is always
set to rts when timeout is non-NULL and then timevalid is set and ets is
only checked later when timervalid is set.