luigi [Tue, 24 Feb 2015 06:20:50 +0000 (06:20 +0000)]
Add native netmap support to ixl.
Preliminary tests indicate 32 Mpps on tx, 24 Mpps on rx
with source and receiver on two different ports of the same 40G card.
Optimizations are likely possible.
The code follows closely the one for ixgbe so i do not
expect stability issues.
neel [Tue, 24 Feb 2015 05:35:15 +0000 (05:35 +0000)]
Always emulate MSR_PAT on Intel processors and don't rely on PAT save/restore
capability of VT-x. This lets bhyve run nested in older VMware versions that
don't support the PAT save/restore capability.
Note that the actual value programmed by the guest in MSR_PAT is irrelevant
because bhyve sets the 'Ignore PAT' bit in the nested PTE.
Reported by: marcel
Tested by: Leon Dang (ldang@nahannisys.com)
Sponsored by: Nahanni Systems
MFC after: 2 weeks
neel [Tue, 24 Feb 2015 02:04:16 +0000 (02:04 +0000)]
Add "-u" option to bhyve(8) to indicate that the RTC should maintain UTC time.
The default remains localtime for compatibility with the original device model
in bhyve(8). This is required for OpenBSD guests which assume that the RTC
keeps UTC time.
Reviewed by: grehan
Pointed out by: Jason Tubnor (jason@tubnor.net)
MFC after: 2 weeks
ken [Mon, 23 Feb 2015 21:59:30 +0000 (21:59 +0000)]
Significant upgrades to sa(4) and mt(1).
The primary focus of these changes is to modernize FreeBSD's
tape infrastructure so that we can take advantage of some of the
features of modern tape drives and allow support for LTFS.
Significant changes and new features include:
o sa(4) driver status and parameter information is now exported via an
XML structure. This will allow for changes and improvements later
on that will not break userland applications. The old MTIOCGET
status ioctl remains, so applications using the existing interface
will not break.
o 'mt status' now reports drive-reported tape position information
as well as the previously available calculated tape position
information. These numbers will be different at times, because
the drive-reported block numbers are relative to BOP (Beginning
of Partition), but the block numbers calculated previously via
sa(4) (and still provided) are relative to the last filemark.
Both numbers are now provided. 'mt status' now also shows the
drive INQUIRY information, serial number and any position flags
(BOP, EOT, etc.) provided with the tape position information.
'mt status -v' adds information on the maximum possible I/O size,
and the underlying values used to calculate it.
o The extra sa(4) /dev entries (/dev/saN.[0-3]) have been removed.
The extra devices were originally added as place holders for
density-specific device nodes. Some OSes (NetBSD, NetApp's OnTap
and Solaris) have had device nodes that, when you write to them,
will automatically select a given density for particular tape drives.
This is a convenient way of switching densities, but it was never
implemented in FreeBSD. Only the device nodes were there, and that
sometimes confused users.
For modern tape devices, the density is generally not selectable
(e.g. with LTO) or defaults to the highest availble density when
the tape is rewritten from BOT (e.g. TS11X0). So, for most users,
density selection won't be necessary. If they do need to select
the density, it is easy enough to use 'mt density' to change it.
o Protection information is now supported. This is either a
Reed-Solomon CRC or CRC32 that is included at the end of each block
read and written. On write, the tape drive verifies the CRC, and
on read, the tape drive provides a CRC for the userland application
to verify.
o New, extensible tape driver parameter get/set interface.
o Density reporting information. For drives that support it,
'mt getdensity' will show detailed information on what formats the
tape drive supports, and what formats the tape drive supports.
o Some mt(1) functionality moved into a new mt(3) library so that
external applications can reuse the code.
o The new mt(3) library includes helper routines to aid in parsing
the XML output of the sa(4) driver, and build a tree of driver
metadata.
o Support for the MTLOAD (load a tape in the drive) and MTWEOFI
(write filemark immediate) ioctls needed by IBM's LTFS
implementation.
o Improve device departure behavior for the sa(4) driver. The previous
implementation led to hangs when the device was open.
o This has been tested on the following types of drives:
IBM TS1150
IBM TS1140
IBM LTO-6
IBM LTO-5
HP LTO-2
Seagate DDS-4
Quantum DLT-4000
Exabyte 8505
Sony DDS-2
lib/libmt/Makefile,
lib/libmt/mt.3,
lib/libmt/mtlib.c,
lib/libmt/mtlib.h,
New mt(3) library that contains functions moved from mt(1) and
new functions needed to interact with the updated sa(4) driver.
This includes XML parser helper functions that application writers
can use when writing code to query tape parameters.
rescue/rescue/Makefile:
Add -lmt to CRUNCH_LIBS.
src/share/man/man4/mtio.4
Clarify this man page a bit, and since it contains what is
essentially the mtio.h header file, add new ioctls and structure
definitions from mtio.h.
src/share/man/man4/sa.4
Update BUGS and maintainer section.
sys/cam/scsi/scsi_all.c,
sys/cam/scsi/scsi_all.h:
Add SCSI SECURITY PROTOCOL IN/OUT CDB definitions and CDB building
functions.
sys/cam/scsi/scsi_sa.c
sys/cam/scsi/scsi_sa.h
Many tape driver changes, largely outlined above.
Increase the sa(4) driver read/write timeout from 4 to 32
minutes. This is based on the recommended values for IBM LTO
5/6 drives. This may also avoid timeouts for other tape
hardware that can take a long time to do retries and error
recovery. Longer term, a better way to handle this is to ask
the drive for recommended timeout values using the REPORT
SUPPORTED OPCODES command. Modern IBM and Oracle tape drives
at least support that command, and it would allow for more
accurate timeout values.
Add XML status generation. This is done with a series of
macros to eliminate as much duplicate code as possible. The
new XML-based status values are reported through the new
MTIOCEXTGET ioctl.
Add XML driver parameter reporting, using the new MTIOCPARAMGET
ioctl.
Add a new driver parameter setting interface, using the new
MTIOCPARAMSET and MTIOCSETLIST ioctls.
Add a new MTIOCRBLIM ioctl to get block limits information.
Add CCB/CDB building routines scsi_locate_16, scsi_locate_10,
and scsi_read_position_10().
scsi_locate_10 implements the LOCATE command, as does the
existing scsi_set_position() command. It just supports
additional arguments and features. If/when we figure out a
good way to provide backward compatibility for older
applications using the old function API, we can just revamp
scsi_set_position(). The same goes for
scsi_read_position_10() and the existing scsi_read_position()
function.
Revamp sasetpos() to take the new mtlocate structure as an
argument. It now will use either scsi_locate_10() or
scsi_locate_16(), depending upon the arguments the user
supplies. As before, once we change position we don't have a
clear idea of what the current logical position of the tape
drive is.
For tape drives that support long form position data, we
read the current position and store that for later reporting
after changing the position. This should help applications
like Bacula speed tape access under FreeBSD once they are
modified to support the new ioctls.
Add a new quirk, SA_QUIRK_NO_LONG_POS, that is set for all
drives that report SCSI-2 or older, as well as drives that
report an Illegal Request type error for READ POSITION with
the long format. So we should automatically detect drives
that don't support the long form and stop asking for it after
an initial try.
Add a partition number to the sa(4) softc.
Improve device departure handling. The previous implementation
led to hangs when the device was open.
If an application had the sa(4) driver open, and attempted to
close it after it went away, the cam_periph_release() call in
saclose() would cause the periph to get destroyed because that
was the last reference to it. Because destroy_dev() was
called from the sa(4) driver's cleanup routine (sacleanup()),
and would block waiting for the close to happen, a deadlock
would result.
So instead of calling destroy_dev() from the cleanup routine,
call destroy_dev_sched_cb() from saoninvalidate() and wait for
the callback.
Acquire a reference for devfs in saregister(), and release it
in the new sadevgonecb() routine when all devfs devices for
the particular sa(4) driver instance are gone.
Add a new function, sasetupdev(), to centralize setting
per-instance devfs device parameters instead of repeating the
code in saregister().
Add an open count to the softc, so we know how many
peripheral driver references are a result of open
sessions.
Add the D_TRACKCLOSE flag to the cdevsw flags so
that we get a 1:1 mapping of open to close calls
instead of a N:1 mapping.
This should be a no-op for everything except the
control device, since we don't allow more than one
open on non-control devices.
However, since we do allow multiple opens on the
control device, the combination of the open count
and the D_TRACKCLOSE flag should result in an
accurate peripheral driver reference count, and an
accurate open count.
The accurate open count allows us to release all
peripheral driver references that are the result
of open contexts once we get the callback from devfs.
sys/sys/mtio.h:
Add a number of new mt(4) ioctls and the requisite data
structures. None of the existing interfaces been removed
or changed.
This includes definitions for the following new ioctls:
MTIOCRBLIM /* get block limits */
MTIOCEXTLOCATE /* seek to position */
MTIOCEXTGET /* get tape status */
MTIOCPARAMGET /* get tape params */
MTIOCPARAMSET /* set tape params */
MTIOCSETLIST /* set N params */
usr.bin/mt/Makefile:
mt(1) now depends on libmt, libsbuf and libbsdxml.
usr.bin/mt/mt.1:
Document new mt(1) features and subcommands.
usr.bin/mt/mt.c:
Implement support for mt(1) subcommands that need to
use getopt(3) for their arguments.
Implement a new 'mt status' command to replace the old
'mt status' command. The old status command has been
renamed 'ostatus'.
The new status function uses the MTIOCEXTGET ioctl, and
therefore parses the XML data to determine drive status.
The -x argument to 'mt status' allows the user to dump out
the raw XML reported by the kernel.
The new status display is mostly the same as the old status
display, except that it doesn't print the redundant density
mode information, and it does print the current partition
number and position flags.
Add a new command, 'mt locate', that will supersede the
old 'mt setspos' and 'mt sethpos' commands. 'mt locate'
implements all of the functionality of the MTIOCEXTLOCATE
ioctl, and allows the user to change the logical position
of the tape drive in a number of ways. (Partition,
block number, file number, set mark number, end of data.)
The immediate bit and the explicit address bits are
implemented, but not documented in the man page.
Add a new 'mt weofi' command to use the new MTWEOFI ioctl.
This allows the user to ask the drive to write a filemark
without waiting around for the operation to complete.
Add a new 'mt getdensity' command that gets the XML-based
tape drive density report from the sa(4) driver and displays
it. This uses the SCSI REPORT DENSITY SUPPORT command
to get comprehensive information from the tape drive about
what formats it is able to read and write.
Add a new 'mt protect' command that allows getting and setting
tape drive protection information. The protection information
is a CRC tacked on to the end of every read/write from and to
the tape drive.
ian [Mon, 23 Feb 2015 20:09:05 +0000 (20:09 +0000)]
There is no reason to do i+dcache writeback and invalidate when changing
the translation table (this may be left over from armv5 days). It's
especially bad to do so using a cache operation that isn't coherent on
SMP systems.
glebius [Mon, 23 Feb 2015 18:57:09 +0000 (18:57 +0000)]
A lot of current code in network stack expects mbufs not having
m_nextpkt pointer, assuming that if there is one, then this is
a packet batch. Thus, mbufq_dequeue() needs to clear it on mbuf
that is being returned.
hselasky [Mon, 23 Feb 2015 17:01:38 +0000 (17:01 +0000)]
Add support for the DWC OTG v2 chipset found in the STM32F4 series of
processors. Make sure we pullup the data lines in device mode when we
power on the port.
ae [Mon, 23 Feb 2015 13:41:35 +0000 (13:41 +0000)]
In some cases soreceive_dgram() can return no data, but has control
message. This can happen when application is sending packets too big
for the path MTU and recvmsg() will return zero (indicating no data)
but there will be a cmsghdr with cmsg_type set to IPV6_PATHMTU.
Remove KASSERT() which does NULL pointer dereference in such case.
Also call m_freem() only when m isn't NULL.
nwhitehorn [Sun, 22 Feb 2015 21:40:27 +0000 (21:40 +0000)]
Kernel support for the Vector-Scalar eXtension (VSX) found on the POWER7
and POWER8. This instruction set unifies the 32 64-bit scalar floating
point registers with the 32 128-bit vector registers into a single bank
of 64 128-bit registers. Kernel support mostly amounts to saving and
restoring the wider version of the floating point registers and making
sure that both scalar FP and vector registers are enabled once a VSX
instruction is executed. get_mcontext() and friends currently cannot
see the high bits, which will require a little more work.
As the system compiler (GCC 4.2) does not support VSX, making use of this
from userland requires either newer GCC or clang.
nwhitehorn [Sun, 22 Feb 2015 20:52:29 +0000 (20:52 +0000)]
Add some opcodes for assembling forthcoming VSX (Vector-Scalar eXtension)
support in the kernel. Userspace programs are expected to rely on LLVM's
integrated assembler or newer binutils.
arybchik [Sun, 22 Feb 2015 19:24:08 +0000 (19:24 +0000)]
sfxge: add common code support for changing TX queue pace
To delay packets from a particular TX queue by a particular time, write a value
into the TX Pace table s.t. pace time <= TX Pace Clock Period * (2 ^ pace value)
- the TX pace clock is 1/13 of the system clock, so its period should be 104 or
52 ns depending on whether turbo mode is active.
EFX_TX_PACE_CLOCK_BASE added by me.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
arybchik [Sun, 22 Feb 2015 18:54:16 +0000 (18:54 +0000)]
sfxge: do no allow EFSYS_MEM_ALLOC sleep
It solves locking problem when EFSYS_MEM_ALLOC is called in
the context holding a mutex (not allowed to sleep).
E.g. on interface bring up or multicast addresses addition.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
arybchik [Sun, 22 Feb 2015 18:50:59 +0000 (18:50 +0000)]
sfxge: pass correct address to free allocated memory in the case of load error
It is one more place missed in the previous fix.
Most likely is was just memory leak on the error handling path since
typically efsys_mem_t is filled in by zeros on allocation.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
dim [Sun, 22 Feb 2015 15:51:49 +0000 (15:51 +0000)]
Pull in r230058 from upstream llvm trunk (by Benjamin Kramer):
LoopRotate: When reconstructing loop simplify form don't split edges
from indirectbrs.
Yet another chapter in the endless story. While this looks like we
leave the loop in a non-canonical state this replicates the logic in
LoopSimplify so it doesn't diverge from the canonical form in any way.
http://llvm.org/PR21968
This fixes a "Cannot split critical edge from IndirectBrInst" assertion
failure when building the devel/radare2 port.
andrew [Sun, 22 Feb 2015 11:11:05 +0000 (11:11 +0000)]
Add support to the bcm2835 mailbox driver to work before interrupts are
enabled. This will be needed to enable the power on devices early on in the
boot process.
cperciva [Sun, 22 Feb 2015 08:50:05 +0000 (08:50 +0000)]
Step 2 of eliminating the "games" distribution: Remove punch card
utilities.
I was originally planning on removing the phase-of-moon (pom), clock
(grdc), and caesar cipher (caesar, rot13) utilities as well, but after
I committed r278616 I received an astonishing volume of email informing
me that those are still being widely used. Much to my relief, nobody
reported continuing to use the punch card utilities in production.
The final step will be to merge src/games into src/usr.bin.
arybchik [Sun, 22 Feb 2015 07:08:57 +0000 (07:08 +0000)]
sfxge: style fixes and cleanup
Sync endif comment with conditional.
BOOTROM and SIENA_BOOTROM are the same, but highlight that it is Siena.
Restore commented out assertion.
Sync comments with out-of-tree driver.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
marcel [Sun, 22 Feb 2015 04:50:47 +0000 (04:50 +0000)]
Add the -c option for specifying the capacity of the disk image. When
a capcity is given, no partitions are required. When no partitions are
given, no scheme needs to be specified either. This makes it possible
to create an entirely empty disk image. To add an empty partitioning
table, specify the scheme.
marcel [Sun, 22 Feb 2015 01:20:49 +0000 (01:20 +0000)]
Don't require a scheme if no partitions are given. Change the code
to handle that case. Note that we still require partitions, so the
change is effectively a no-op.
marcel [Sun, 22 Feb 2015 01:01:02 +0000 (01:01 +0000)]
In scheme_write(), don't overwrite the end parameter with the
return value of image_get_size(). As it so happens, the only
caller of scheme_write() passes exactly that.
marcel [Sat, 21 Feb 2015 23:47:20 +0000 (23:47 +0000)]
Convert netstat to use libxo.
Obtained from: Phil Shafer <phil@juniper.net>
Ported to -current by: alfred@ (mostly), Kim Shrier
Formatting: marcel@
Sponsored by: Juniper Networks, Inc.
kib [Sat, 21 Feb 2015 22:38:32 +0000 (22:38 +0000)]
Revert r276949 and redo the fix for PCIe/PCI bridges, which do not
follow specification and do not provide PCIe capability.
Verify if the port above such bridge is downstream PCIe (or root port)
and treat the bridge as PCIe/PCI then. This allows to avoid
maintaining the table of device ids for bridges without capability,
while still calculate correct request originator for devices behind
the bridge.
Submitted by: Jason Harmening <jason.harmening@gmail.com>
MFC after: 1 week
arybchik [Sat, 21 Feb 2015 06:28:31 +0000 (06:28 +0000)]
sfxge: allow TX and RX queue limits to be changed
Before the common code had hard coded limits on the IDs RXQs and TXQs could
be created with which were suited for the Windows driver with VMQ, and so
would prevent queues with IDs greater than or equal to 259 (for TXQs) or 768
(for RXQs) from being created. This change allows the limits to be set in
efsys.h, so that all 1024 queues can be created during new manftest tests.
Also, the descriptor cache sizes were also hard coded to values suited to
the smaller queue counts, and so it was necessary to make them configurable
as well.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
arybchik [Sat, 21 Feb 2015 06:26:10 +0000 (06:26 +0000)]
sfxge: never set RX_DESCQ_EN during self-test
We must not enable RX queues with random parameters when they are
mapped into a VF with an untrusted driver. It's probably not a good
idea to do this anyway, so take this bit out of the table test masks.
Submitted by: Ben Hutchings
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
np [Fri, 20 Feb 2015 22:57:54 +0000 (22:57 +0000)]
cxgbe(4): there is no need to force an "unimplemented" panic needlessly.
The calls to free_nm_txq and free_nm_rxq are made just a few lines prior
to the panic.
jamie [Fri, 20 Feb 2015 20:12:05 +0000 (20:12 +0000)]
Fix the logic for skipping parameters (with -s) that have "jailsys"
parents (such as host.hostname); these were being skipped all the time.
That it went this long without anyone noticing is a sign that this feature
isn't actually used by anyone, but it's there so it might as well work.
arybchik [Fri, 20 Feb 2015 19:42:05 +0000 (19:42 +0000)]
sfxge: add assertions that required event handlers are implemented
efx_ev_mcdi() does not assert or check that all event handlers it
calls are non-null. Add assertions at the top for all required
event handlers, as some events (in the case of this bug, monitor
events) are rare.
Submitted by: Ben Hutchings
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
gjb [Fri, 20 Feb 2015 17:46:15 +0000 (17:46 +0000)]
Document r278433, xz(1) update to 5.2.0.
Separately document multi-threaded support to keep the
version update separate, so it remains correct if xz(1)
is updated again.