Eliminate the ega renderer switch. It did nothing useful except hold
a pointer to the main ega drawing method which is misoptimized be in
a different function than the main vga planar mode drawing method.
Vga initialization handles everything with no extra code except for
selecting the different function.
When the character width is 9, remove vertical lines in the mouse cursor
corresponding to the gaps between characters. This fixes distortion
of the cursor due to expanding it across the gaps.
Again for character width 9, when the cursor characters are not in the
graphics range (0xb0-0xdf), the gaps were always there (filled in the
background color for the previous char). They still look strange, but
don't cause distortion. When the cursor characters are in the graphics
range, the gaps are filled by repeating the previous line. This gives
distortion with cilia. Removing vertical lines reduces the distortion
to vertical cilia.
Move the default for the cursor characters out of the graphics range.
With character width 9, this gives gaps instead of distortion and
other problems. With character width 8, it just fixes a smaller set
of other problems. Some distortion and other problems can be recovered
using vidcontrol -M. Presumably the default was to fill the gaps
intentionally, but it is much better to leave gaps. The gaps can even
be considered as a feature for text processing -- they give sub-pointers
to character boundaries. The other problems are: (1) with character
width 9, characters near the cursor are moved into the graphics range
and thus distorted if any of their 8th bits is set; (2) conflicts with
national characters in the graphics range.
The default range for the graphics cursor characters is now 8-11. This
doesn't conflict with anything, since the glyphs for the characters in
this range are unreachable.
Use the 10x16 mouse cursor in text mode too (if the font size is >= 14).
When the character width is 9, removal of 1 or 2 vertical lines makes
10x16 cursor no wider than the 9x13 one usually was. We could even
handle cursors 1 pixel wider in 2 character cells and gaps without
more clipping than given by the gaps (the worst case is 1 pixel in the
left cell, 1 removed in the middle gap, 8 in the right cell and 1
removed in the right gap. The pixel in the right gap is removed so
it doesn't matter if it is in the font).
When the character width is 8, we now clip the 10-wide cursor by 1
pixel in the worst case. This clipping is usually invisible since it
is of the border and and the border usually merges with the background
so is invisible. There should be an option to use reverse video to
highlight the border and its tip instead of the interior (graphics
mode can do better using separate colors). This needs the 9x13 cursor
again.
Ideas from: ache (especially about the bad default character range)
andrew [Thu, 20 Apr 2017 15:53:20 +0000 (15:53 +0000)]
Restrict the arm64 supervisor all instructions to only allow a zero
immediate value for system calls. We may wish to use other values in the
future for other purposes.
Write-combine framebuffer writes through user-space mappings, if possible.
Note that KVA mapping of the framebuffer already uses write-combining
mode, so the change, besides improving speed of user mode writes, also
satisfies requirement of the IA32 architecture of using consistent
caching modes for multiple mappings of the same page.
Reported and tested by: bde
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
etcupdate(8) requires that option, while GNU diff supports many more variation
of that options, their behaviour beside the simple verion implemented here are
quite inconsistent as such I do not plan to implement those.
The only special keyword supported by this implementation are: %< and %>
%= is not implemented as the documentation of GNU diff says: common lines, but
it actually when tested print the changes from the first file
andrew [Thu, 20 Apr 2017 13:56:30 +0000 (13:56 +0000)]
Push loading curthread into assembly in the synchronous exception handlers.
This will help investigating the performance impact of moving parts of the
switch statement in do_el0_sync into assembly.
ePAPR states that any non-boot CPU will come in "disabled" state. So we should
not consider a "disabled" cpu as a CPU we have to ignore, and we should use
them if they provide a "enable-method".
While I'm there, support "ok" as well as "okay", while ePAPR only accepts
"okay", linux accepts "ok" too so we can expect it to be used.
Attempt to determine the modes in which 8-bit wide characters are actually
9 wide.
I only need this to improve the mouse cursor, but it has always been
needed to select and/or adjust fonts.
This is complicated because there are no standard parameter tables
giving this bit of information directly, and the device register bit
giving the information can't be trusted even if it is read from the
hardware. Use a heuristic to guess if the device register can be
trusted. (The device register is normally read from the BIOS mode
table, but on my system where the device register is wrong, the mode
table doesn't match the hardware and is not used; the device registers
are used in this case.)
When forwarding pf tracks the size of the largest fragment in a fragmented
packet, and refragments based on this size.
It failed to ensure that this size was a multiple of 8 (as is required for all
but the last fragment), so it could end up generating incorrect fragments.
For example, if we received an 8 byte and 12 byte fragment pf would emit a first
fragment with 12 bytes of payload and the final fragment would claim to be at
offset 8 (not 12).
We now assert that the fragment size is a multiple of 8 in ip6_fragment(), so
other users won't make the same mistake.
Reported by: Antonios Atlasis <aatlasis at secfu net>
MFC after: 3 days
Remove WITHOUT_GNU and WITHOUT_GNU_SUPPORT src.conf.knobs
These have no effect (and WITHOUT_GNU is documented as having no
effect). I intend to later introduce a WITHOUT_GPL knob to serve a
similar purpose as WITHOUT_GNU's previously documented intent, but with
a more accurate name. To avoid confusion over the transition though just
remove the existing, nonfunctional ones.
Fix missing support for drawing the mouse cursor in depth 24 of direct
mode.
Use the general DRAWPIXEL() macro with its bigger case statement
(twice) instead of our big case statement (once). DRAWPIXEL() is more
complicated since it is not missing support for depth 24 or
complications for colors in depth 16 (we currently hard-code black and
white so the complications for colors are not needed). DRAWPIXEL()
also does the bpp calculation in the inner loop. Compilers optimize
DRAWPIXEL() well enough, and the main text drawing method always
depended on this. In direct mode, mouse cursor drawing is now similar
to normal text drawing except it draws in 2 hard-coded colors instead
of 1 variable color.
This also fixes a nested hard-coding of colors. DRAWPIXEL() uses the
palette in all cases, but the direct code didn't use the palette for
its hard-coded black. This only had an effect in depth 8, since
changing the palette is not supported in other depths.
Stop using a saveunder method for mouse cursor drawing in the vga
direct mode renderer. I thought that reads were not much slower than
writes, so that the method only tripled the time for the whole function,
but I recently measured that video memory reads can be up to 53 times
slower than writes in tighter loops than here. Loop overheap here
reduces the multiplier to only 16-20 on Haswell.
Start cleaning up and fixing larger bugs in this function. Only replace
the 22-line removal loop by a 3-line one for now, since adjusting the
old loop would have required many palette calculations which are better
done in the DRAW_PIXEL() macro. This also fixes missing support for
depth 24, but only for removal.
Removal is currently sloppy at the right bottom corner. It sometimes
leaks border color into the text window. This is soon cleaned up by the
caller. The planar renderer has complications to clip at the corner.
Add infrastructure to the ATA and SCSI transports that supports
using a driver-supplied sbuf for printing device discovery
announcements. This helps ensure that messages to the console
will be properly serialized (through sbuf_putbuf) and not be
truncated and interleaved with other messages. The
infrastructure mirrors the existing xpt_announce_periph()
entry point and is opt-in for now. No content or formatting
changes are visible to the operator other than the new coherency.
While here, eliminate the stack usage of the temporary
announcement buffer in some of the drivers. It's moved to the
softc for now, but future work will eliminate it entirely by
making the code flow more linear. Future work will also address
locking so that the sbufs can be dynamically sized.
The scsi_da, scs_cd, scsi_ses, and ata_da drivers are converted
at this point, other drivers can be converted at a later date.
A tunable+sysctl, kern.cam.announce_nosbuf, exists for testing
purposes but will be removed later.
TODO:
Eliminate all of the code duplication and temporary buffers. The
old printf-based methods will be retired, and xpt_announce_periph()
will just be a wrapper that uses a dynamically sized sbuf. This
requires that the register and deregister paths be made malloc-safe,
which they aren't currently.
When we don't use the parameter table in the BIOS, also don't use most
of our tweaked modes based on it. In practice, this means limiting the
tweaked modes to at most 80x50 based on 80x25, so there are no 90-column,
80x30 or 80x60 modes.
This happens when the the initial mode is is not in the parameter
table. We always detected this case, but assumed that the (necessarily
nonstandard) parameters of the initial mode could be tweaked just as
blindly as the probably-standard parameters of initial modes in the
table.
On 1 laptop system with near-VGA where the initial mode is nonstandard,
this is because the hardware apparently doesn't support 9-bit mode,
but otherwise has standard timing. The initial mode has 8-bit mode
CRTC horizontal parameters similar to those in syscons' 90-column modes
and in EGA modes. Tweaking these values for the 90-column modes has
little effect except to print the extra 10 columns off the screen.
Tweaking from 80x25 to 80x30 requires changing from 400 scan lines to
480. This can probably be made to work, but syscons blindly applies
values based on standard timing. This gives blank output. Tweaking
from 80x25 to 80x50 doesn't change the CRTC timing and works.
Fix problem regarding priority inversion when using the concurrency
kit, CK, in the LinuxKPI.
When threads are pinned to a CPU core or when there is only one CPU,
it can happen that a higher priority thread can call the CK
synchronize function while a lower priority thread holds the read
lock. Because the CK's synchronize is a simple wait loop this can lead
to a deadlock situation. To solve this problem use the recently
introduced CK's wait callback function.
When detecting a CK blocking condition figure out the lowest priority
among the blockers and update the calling thread's priority and
yield. If another CPU core is holding the read lock, pin the thread to
the blocked CPU core and update the priority. The calling threads
priority and CPU bindings are restored before return.
If a thread holding a CK read lock is detected to be sleeping, pause()
will be used instead of yield().
Zero number of CPUs should be translated into the default number of
CPUs when allocating a LinuxKPI workqueue. This also ensures that the
created taskqueue always have a non-zero number of worker threads.
Use hwreset_get_by_ofw_idx() function instead, since there is
no reset-names dts property defined for IR in case of H3 SoC.
That way IR works on H3 SoC based board.
Tested on Orangepi mini 2 board.
cem [Tue, 18 Apr 2017 21:05:05 +0000 (21:05 +0000)]
da(4): Fix a TRIM regression introduced in r308155
According to Warner, multiple TRIM BIOs are collapsed into a single CCB with
NULL bp. It is invalid to biotrack() NULL, and results in a fault. So,
don't do that.
Regenerate to note that GDB is now off by default on most platforms.
Note that this commit also adds the default riscv settings for all
options since riscv was added to 'make targets' since the last time
this was generated.
As the uboot disk interface is using common/disk.c API, we also
should use disk_ioctl() call, this will give us chance to read partition
sizes and have feature parity with UEFI and BIOS implementations.
This does also fix arm boot issue on some systems, reported/tested by Ian,
thanks.
Reported by: ian
Reviewed by: ian
Differential Revision: https://reviews.freebsd.org/D10421
loader: F_READ/F_WRITE should be checked against masked flag
The work to make it possible to avoid bcache via using F_NORA modifier did
miss the fact that not all loader platforms are using the bcache, and so
it is possible the modifier is not cleared, as bcache strategy function is
not used.
For fix, we make sure the checks are dont with masked flag.
This patch does fix boot for platforms which do not use bcache.
Disable in-tree GDB by default on x86, mips, and powerpc.
GDB in ports contains all of the functionality as GDB in base
(including kgdb) for these platforms along with additional
functionality. In-tree GDB remains enabled on ARM and sparc64.
GDB in ports does not currently support kernel debugging on arm,
and ports GDB for sparc64 has not been tested (though it does
include sparc64 support).
loader: zfs reader vdev_probe should check for minimum device size
The smallest device we can have in the pool is 64MB, since we are trying to
walk all four labels to find the most up to date uberblock, this limit will
also give us good method to check if we even should attempt to probe.
Enforcing the check also will make sure we are not getting wrapped while
calculating the label offset.
Also, after label check, we should verify if we actually got any UB or not.
Execute PL310_ERRATA_727915 only for related revisions
Part of PL310 erratum 727915 in pl310_wbinv_range() was
executed uncoditionally for all possible controllers'
revisions. This patch adds appropriate condition, since
extra operations are required only for revisions between
r2p0 and r3p0.
Increase number of L2 tables required for kernel bootstrap
Memory space reserved for pmap_kernel_l2dtable_kva and
pmap_kernel_l2ptp_kva has not been taken into account in
original code. All the memory reserved from kernel space by
pmap_alloc_specials() function called in pmap_bootstrap()
should be mapped initially by initarm(). To create initial
mapping initarm() function reserves proper number of l2 page
tables. However the number of the l2 page tables does not take
into account memory for: pmap_kernel_l2ptp_kva,
pmap_kernel_l2dtable_kva, crashdumpmap, etc.
VM_KMEM_SIZE_MAX allows to limit kmem arena size. In our case this was
necessary, as decreasing size of kmem_arena leaves more space for
kernel_arena.
kernel_arena is pool used for contigmalloc (in effect, DMA) allocations,
which failed on Armada38x. This resulted in 'no memory errors'
(e.g. USB_ERR_NOMEM errors) and failure of whole system. The need for
greater size of kernel_arena probably comes from more peripherals making
use of busdma.
Value used as upper limit is half of the default value
(0x1399a000).
- Improve C++ demangling
- Improve compatibility with Binutils tools wrt. error messages
- Handle additional types/sections/etc. in readelf and elfdump
- addr2line, cxxfilt: use setvbuf to set line buffering for filter use
PR: 218395
MFC after: 2 weeks
Relnotes: Yes
Sponsored by: The FreeBSD Foundation
When application reads large directory, calling telldir() for each entry,
like Samba does, it creates exponential performance drop as number of
entries reach tenths to hundreds of thousands. It is caused by full search
through the internal list, that never finds matches in that scenario, but
creates O(n^2) delays. This patch optimizes that search, limiting it to
entries of the same buffer, turning time closer to O(n) in case of linear
directory scan.
- Remove 'struct vmmeter' from 'struct pcpu', leaving only global vmmeter
in place. To do per-cpu stats, convert all fields that previously were
maintained in the vmmeters that sit in pcpus to counter(9).
- Since some vmmeter stats may be touched at very early stages of boot,
before we have set up UMA and we can do counter_u64_alloc(), provide an
early counter mechanism:
o Leave one spare uint64_t in struct pcpu, named pc_early_dummy_counter.
o Point counter(9) fields of vmmeter to pcpu[0].pc_early_dummy_counter,
so that at early stages of boot, before counters are allocated we already
point to a counter that can be safely written to.
o For sparc64 that required a whole dummy pcpu[MAXCPU] array.
Further related changes:
- Don't include vmmeter.h into pcpu.h.
- vm.stats.vm.v_swappgsout and vm.stats.vm.v_swappgsin changed to 64-bit,
to match kernel representation.
- struct vmmeter hidden under _KERNEL, and only vmstat(1) is an exclusion.
This is based on benno@'s 4-year old patch:
https://lists.freebsd.org/pipermail/freebsd-arch/2013-July/014471.html
- Report missing includes at the correct location.
- Add initial support for the -@ option emitting a symbol table.
- Add support for running tests with and without -@
- Add support for generating __fixups__ and __local_fixups__
- Attach the to-string transform to the node path.
bsdgrep: remove output separators between overlapping segments
Make bsdgrep more sensitive to context overlaps. If it's printing
context that either overlaps or is immediately adjacent to another bit
of context, don't print a separator.
- Non-overlapping segments no longer have two separators between them
- Overlapping segments no longer have separators between them with
overlapping sections repeated
Submitted by: Kyle Evans <kevans91 at ksu.edu>
Reviewed by: cem
Differential Revision: https://reviews.freebsd.org/D10105
-z treats input and output data as sequences of lines terminated by a
zero byte instead of a newline. This brings it more in line with GNU grep
and brings us closer to passing the current tests with BSD grep.
Submitted by: Kyle Evans <kevans91 at ksu.edu>
Reviewed by: cem
Relnotes: Yes
Differential Revision: https://reviews.freebsd.org/D10101