sys/gnu/dts/arm/omap5-cm-t54.dts

   1 /*
   2  * Support for CompuLab CM-T54
   3  */
   4 /dts-v1/;
   5
   6 #include "omap5.dtsi"
   7 #include <dt-bindings/interrupt-controller/irq.h>
   8 #include <dt-bindings/interrupt-controller/arm-gic.h>
   9
  10 / {
  11         model = "CompuLab CM-T54";
  12         compatible = "compulab,omap5-cm-t54", "ti,omap5";
  13
  14         memory {
  15                 device_type = "memory";
  16                 reg = <0x80000000 0x7F000000>; /* 2048 MB */
  17         };
  18
  19         aliases {
  20                 display0 = &hdmi0;
  21                 display1 = &dvi0;
  22                 display2 = &lcd0;
  23         };
  24
  25         vmmcsd_fixed: fixed-regulator-mmcsd {
  26                 compatible = "regulator-fixed";
  27                 regulator-name = "vmmcsd_fixed";
  28                 regulator-min-microvolt = <3300000>;
  29                 regulator-max-microvolt = <3300000>;
  30         };
  31
  32         vwlan_pdn_fixed: fixed-regulator-vwlan-pdn {
  33                 compatible = "regulator-fixed";
  34                 regulator-name = "vwlan_pdn_fixed";
  35                 regulator-min-microvolt = <3300000>;
  36                 regulator-max-microvolt = <3300000>;
  37                 vin-supply = <&ldo2_reg>;
  38                 gpio = <&gpio4 13 GPIO_ACTIVE_HIGH>;   /* gpio4_109 */
  39                 startup-delay-us = <1000>;
  40                 enable-active-high;
  41         };
  42
  43         vwlan_fixed: fixed-regulator-vwlan {
  44                 compatible = "regulator-fixed";
  45                 regulator-name = "vwlan_fixed";
  46                 regulator-min-microvolt = <3300000>;
  47                 regulator-max-microvolt = <3300000>;
  48                 vin-supply = <&vwlan_pdn_fixed>;
  49                 gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>;   /* gpio4_110 */
  50                 startup-delay-us = <1000>;
  51                 enable-active-high;
  52         };
  53
  54         ads7846reg: ads7846-reg {
  55                 compatible = "regulator-fixed";
  56                 regulator-name = "ads7846-reg";
  57                 regulator-min-microvolt = <3300000>;
  58                 regulator-max-microvolt = <3300000>;
  59         };
  60
  61         /* HS USB Host PHY on PORT 2 */
  62         hsusb2_phy: hsusb2_phy {
  63                 compatible = "usb-nop-xceiv";
  64                 reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */
  65         };
  66
  67         /* HS USB Host PHY on PORT 3 */
  68         hsusb3_phy: hsusb3_phy {
  69                 compatible = "usb-nop-xceiv";
  70                 reset-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 ETH_RESET */
  71         };
  72
  73         leds {
  74                 compatible = "gpio-leds";
  75                 led@1 {
  76                         label = "Heartbeat";
  77                         gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 ACT_LED */
  78                         linux,default-trigger = "heartbeat";
  79                         default-state = "off";
  80                 };
  81         };
  82
  83         lcd0: display {
  84                 compatible = "startek,startek-kd050c", "panel-dpi";
  85                 label = "lcd";
  86
  87                 pinctrl-names = "default";
  88                 pinctrl-0 = <&lcd_pins>;
  89
  90                 enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
  91
  92                 panel-timing {
  93                         clock-frequency = <33000000>;
  94                         hactive = <800>;
  95                         vactive = <480>;
  96                         hfront-porch = <40>;
  97                         hback-porch = <40>;
  98                         hsync-len = <43>;
  99                         vback-porch = <29>;
 100                         vfront-porch = <13>;
 101                         vsync-len = <3>;
 102                         hsync-active = <0>;
 103                         vsync-active = <0>;
 104                         de-active = <1>;
 105                         pixelclk-active = <1>;
 106                 };
 107
 108                 port {
 109                         lcd_in: endpoint {
 110                                 remote-endpoint = <&dpi_lcd_out>;
 111                         };
 112                 };
 113         };
 114
 115         hdmi0: connector@0 {
 116                 compatible = "hdmi-connector";
 117                 label = "hdmi";
 118
 119                 type = "a";
 120
 121                 pinctrl-names = "default";
 122                 pinctrl-0 = <&hdmi_conn_pins>;
 123
 124                 hpd-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */
 125
 126                 port {
 127                         hdmi_connector_in: endpoint {
 128                                 remote-endpoint = <&hdmi_out>;
 129                         };
 130                 };
 131         };
 132
 133         tfp410: encoder@0 {
 134                 compatible = "ti,tfp410";
 135
 136                 ports {
 137                         #address-cells = <1>;
 138                         #size-cells = <0>;
 139
 140                         port@0 {
 141                                 reg = <0>;
 142
 143                                 tfp410_in: endpoint@0 {
 144                                         remote-endpoint = <&dpi_dvi_out>;
 145                                 };
 146                         };
 147
 148                         port@1 {
 149                                 reg = <1>;
 150
 151                                 tfp410_out: endpoint@0 {
 152                                         remote-endpoint = <&dvi_connector_in>;
 153                                 };
 154                         };
 155                 };
 156         };
 157
 158         dvi0: connector@1 {
 159                 compatible = "dvi-connector";
 160                 label = "dvi";
 161
 162                 digital;
 163
 164                 ddc-i2c-bus = <&i2c2>;
 165
 166                 port {
 167                         dvi_connector_in: endpoint {
 168                                 remote-endpoint = <&tfp410_out>;
 169                         };
 170                 };
 171         };
 172 };
 173
 174 &omap5_pmx_wkup {
 175
 176         ads7846_pins: pinmux_ads7846_pins {
 177                 pinctrl-single,pins = <
 178                         0x02 (PIN_INPUT_PULLDOWN | MUX_MODE6)  /* llib_wakereqin.gpio1_wk15 */
 179                 >;
 180         };
 181 };
 182
 183 &omap5_pmx_core {
 184         pinctrl-names = "default";
 185         pinctrl-0 = <
 186                         &led_gpio_pins
 187                         &usbhost_pins
 188         >;
 189
 190         led_gpio_pins: pinmux_led_gpio_pins {
 191                 pinctrl-single,pins = <
 192                         OMAP5_IOPAD(0x00b0, PIN_OUTPUT | MUX_MODE6) /* hsi2_caflag.gpio3_80 */
 193                 >;
 194         };
 195
 196         i2c1_pins: pinmux_i2c1_pins {
 197                 pinctrl-single,pins = <
 198                         OMAP5_IOPAD(0x01f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_scl */
 199                         OMAP5_IOPAD(0x01f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_sda */
 200                 >;
 201         };
 202
 203         i2c2_pins: pinmux_i2c2_pins {
 204                 pinctrl-single,pins = <
 205                         OMAP5_IOPAD(0x01b8, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
 206                         OMAP5_IOPAD(0x01ba, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
 207                 >;
 208         };
 209
 210         mmc1_pins: pinmux_mmc1_pins {
 211                 pinctrl-single,pins = <
 212                         OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */
 213                         OMAP5_IOPAD(0x01e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_cmd */
 214                         OMAP5_IOPAD(0x01e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data2 */
 215                         OMAP5_IOPAD(0x01e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data3 */
 216                         OMAP5_IOPAD(0x01ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data0 */
 217                         OMAP5_IOPAD(0x01ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data1 */
 218                 >;
 219         };
 220
 221         mmc2_pins: pinmux_mmc2_pins {
 222                 pinctrl-single,pins = <
 223                         OMAP5_IOPAD(0x0040, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_clk */
 224                         OMAP5_IOPAD(0x0042, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_cmd */
 225                         OMAP5_IOPAD(0x0044, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data0 */
 226                         OMAP5_IOPAD(0x0046, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data1 */
 227                         OMAP5_IOPAD(0x0048, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data2 */
 228                         OMAP5_IOPAD(0x004a, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data3 */
 229                         OMAP5_IOPAD(0x004c, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data4 */
 230                         OMAP5_IOPAD(0x004e, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data5 */
 231                         OMAP5_IOPAD(0x0050, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data6 */
 232                         OMAP5_IOPAD(0x0052, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data7 */
 233                 >;
 234         };
 235
 236         mmc3_pins: pinmux_mmc3_pins {
 237                 pinctrl-single,pins = <
 238                         OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
 239                         OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
 240                         OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
 241                         OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
 242                         OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
 243                         OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
 244                 >;
 245         };
 246
 247         wlan_gpios_pins: pinmux_wlan_gpios_pins {
 248                 pinctrl-single,pins = <
 249                         OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_ul_data.gpio4_109 */
 250                         OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_dl_data.gpio4_110 */
 251                 >;
 252         };
 253
 254         usbhost_pins: pinmux_usbhost_pins {
 255                 pinctrl-single,pins = <
 256                         OMAP5_IOPAD(0x00c4, PIN_INPUT | MUX_MODE0)  /* usbb2_hsic_strobe */
 257                         OMAP5_IOPAD(0x00c6, PIN_INPUT | MUX_MODE0)  /* usbb2_hsic_data */
 258
 259                         OMAP5_IOPAD(0x01dc, PIN_INPUT | MUX_MODE0)  /* usbb3_hsic_strobe */
 260                         OMAP5_IOPAD(0x01de, PIN_INPUT | MUX_MODE0)  /* usbb3_hsic_data */
 261
 262                         OMAP5_IOPAD(0x00a8, PIN_OUTPUT | MUX_MODE6) /* hsi2_caready.gpio3_76 */
 263                         OMAP5_IOPAD(0x00b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */
 264                 >;
 265         };
 266
 267         dss_hdmi_pins: pinmux_dss_hdmi_pins {
 268                 pinctrl-single,pins = <
 269                         OMAP5_IOPAD(0x013c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec */
 270                         OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl */
 271                         OMAP5_IOPAD(0x0142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda */
 272                 >;
 273         };
 274
 275         lcd_pins: pinmux_lcd_pins {
 276                 pinctrl-single,pins = <
 277                         OMAP5_IOPAD(0x0172, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* timer11_pwm_evt.gpio8_227 */
 278                 >;
 279         };
 280
 281         hdmi_conn_pins: pinmux_hdmi_conn_pins {
 282                 pinctrl-single,pins = <
 283                         OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
 284                 >;
 285         };
 286
 287         dss_dpi_pins: pinmux_dss_dpi_pins {
 288                 pinctrl-single,pins = <
 289                         OMAP5_IOPAD(0x0104, PIN_OUTPUT | MUX_MODE3) /* rfbi_data15.dispc_data15 */
 290                         OMAP5_IOPAD(0x0106, PIN_OUTPUT | MUX_MODE3) /* rfbi_data14.dispc_data14 */
 291                         OMAP5_IOPAD(0x0108, PIN_OUTPUT | MUX_MODE3) /* rfbi_data13.dispc_data13 */
 292                         OMAP5_IOPAD(0x010a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data12.dispc_data12 */
 293                         OMAP5_IOPAD(0x010c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data11.dispc_data11 */
 294                         OMAP5_IOPAD(0x010e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data10.dispc_data10 */
 295                         OMAP5_IOPAD(0x0110, PIN_OUTPUT | MUX_MODE3) /* rfbi_data9.dispc_data9 */
 296                         OMAP5_IOPAD(0x0112, PIN_OUTPUT | MUX_MODE3) /* rfbi_data8.dispc_data8 */
 297                         OMAP5_IOPAD(0x0114, PIN_OUTPUT | MUX_MODE3) /* rfbi_data7.dispc_data7 */
 298                         OMAP5_IOPAD(0x0116, PIN_OUTPUT | MUX_MODE3) /* rfbi_data6.dispc_data6 */
 299                         OMAP5_IOPAD(0x0118, PIN_OUTPUT | MUX_MODE3) /* rfbi_data5.dispc_data5 */
 300                         OMAP5_IOPAD(0x011a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data4.dispc_data4 */
 301                         OMAP5_IOPAD(0x011c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data3.dispc_data3 */
 302                         OMAP5_IOPAD(0x011e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data2.dispc_data2 */
 303                         OMAP5_IOPAD(0x0120, PIN_OUTPUT | MUX_MODE3) /* rfbi_data1.dispc_data1 */
 304                         OMAP5_IOPAD(0x0122, PIN_OUTPUT | MUX_MODE3) /* rfbi_data0.dispc_data0 */
 305                         OMAP5_IOPAD(0x0124, PIN_OUTPUT | MUX_MODE3) /* rfbi_we.dispc_vsync */
 306                         OMAP5_IOPAD(0x0126, PIN_OUTPUT | MUX_MODE3) /* rfbi_cs0.dispc_hsync */
 307                         OMAP5_IOPAD(0x0128, PIN_OUTPUT | MUX_MODE3) /* rfbi_a0.dispc_de */
 308                         OMAP5_IOPAD(0x012a, PIN_OUTPUT | MUX_MODE3) /* rfbi_re.dispc_pclk */
 309                         OMAP5_IOPAD(0x012c, PIN_OUTPUT | MUX_MODE3) /* rfbi_hsync0.dispc_data17 */
 310                         OMAP5_IOPAD(0x012e, PIN_OUTPUT | MUX_MODE3) /* rfbi_te_vsync0.dispc_data16 */
 311                         OMAP5_IOPAD(0x0130, PIN_OUTPUT | MUX_MODE3) /* gpio6_182.dispc_data18 */
 312                         OMAP5_IOPAD(0x0132, PIN_OUTPUT | MUX_MODE3) /* gpio6_183.dispc_data19 */
 313                         OMAP5_IOPAD(0x0134, PIN_OUTPUT | MUX_MODE3) /* gpio6_184.dispc_data20 */
 314                         OMAP5_IOPAD(0x0136, PIN_OUTPUT | MUX_MODE3) /* gpio6_185.dispc_data21 */
 315                         OMAP5_IOPAD(0x0138, PIN_OUTPUT | MUX_MODE3) /* gpio6_186.dispc_data22 */
 316                         OMAP5_IOPAD(0x013a, PIN_OUTPUT | MUX_MODE3) /* gpio6_187.dispc_data23 */
 317                 >;
 318         };
 319
 320         mcspi2_pins: pinmux_mcspi1_pins {
 321                 pinctrl-single,pins = <
 322                         OMAP5_IOPAD(0x00fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
 323                         OMAP5_IOPAD(0x00fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
 324                         OMAP5_IOPAD(0x0100, PIN_INPUT | MUX_MODE0) /* mcspi2_somi */
 325                         OMAP5_IOPAD(0x0102, PIN_INPUT | MUX_MODE0) /* mcspi2_cs0 */
 326                 >;
 327         };
 328 };
 329
 330 &mcspi2 {
 331         pinctrl-names = "default";
 332         pinctrl-0 = <&mcspi2_pins>;
 333
 334         /* touch controller */
 335         ads7846@0 {
 336                 pinctrl-names = "default";
 337                 pinctrl-0 = <&ads7846_pins>;
 338
 339                 compatible = "ti,ads7846";
 340                 vcc-supply = <&ads7846reg>;
 341
 342                 reg = <0>;                              /* CS0 */
 343                 spi-max-frequency = <1500000>;
 344
 345                 interrupt-parent = <&gpio1>;
 346                 interrupts = <15 0>;                    /* gpio1_wk15 */
 347                 pendown-gpio = <&gpio1 15 0>;
 348
 349
 350                 ti,x-min = /bits/ 16 <0x0>;
 351                 ti,x-max = /bits/ 16 <0x0fff>;
 352                 ti,y-min = /bits/ 16 <0x0>;
 353                 ti,y-max = /bits/ 16 <0x0fff>;
 354
 355                 ti,x-plate-ohms = /bits/ 16 <180>;
 356                 ti,pressure-max = /bits/ 16 <255>;
 357
 358                 ti,debounce-max = /bits/ 16 <30>;
 359                 ti,debounce-tol = /bits/ 16 <10>;
 360                 ti,debounce-rep = /bits/ 16 <1>;
 361
 362                 linux,wakeup;
 363         };
 364 };
 365
 366 &mmc1 {
 367         pinctrl-names = "default";
 368         pinctrl-0 = <&mmc1_pins>;
 369         vmmc-supply = <&ldo9_reg>;
 370         bus-width = <4>;
 371 };
 372
 373 &mmc2 {
 374         pinctrl-names = "default";
 375         pinctrl-0 = <&mmc2_pins>;
 376         vmmc-supply = <&vmmcsd_fixed>;
 377         bus-width = <8>;
 378         ti,non-removable;
 379 };
 380
 381 &mmc3 {
 382         pinctrl-names = "default";
 383         pinctrl-0 = <
 384                 &mmc3_pins
 385                 &wlan_gpios_pins
 386         >;
 387         vmmc-supply = <&vwlan_fixed>;
 388         bus-width = <4>;
 389         ti,non-removable;
 390 };
 391
 392 &mmc4 {
 393         status = "disabled";
 394 };
 395
 396 &mmc5 {
 397         status = "disabled";
 398 };
 399
 400 &i2c1 {
 401         pinctrl-names = "default";
 402         pinctrl-0 = <&i2c1_pins>;
 403
 404         clock-frequency = <400000>;
 405
 406         at24@50 {
 407                 compatible = "at24,24c02";
 408                 pagesize = <16>;
 409                 reg = <0x50>;
 410         };
 411
 412         palmas: palmas@48 {
 413                 compatible = "ti,palmas";
 414                 interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
 415                 interrupt-parent = <&gic>;
 416                 reg = <0x48>;
 417                 interrupt-controller;
 418                 #interrupt-cells = <2>;
 419                 ti,system-power-controller;
 420
 421                 extcon_usb3: palmas_usb {
 422                         compatible = "ti,palmas-usb-vid";
 423                         ti,enable-vbus-detection;
 424                         ti,enable-id-detection;
 425                         ti,wakeup;
 426                 };
 427
 428                 rtc {
 429                         compatible = "ti,palmas-rtc";
 430                         interrupt-parent = <&palmas>;
 431                         interrupts = <8 IRQ_TYPE_NONE>;
 432                 };
 433
 434                 palmas_pmic {
 435                         compatible = "ti,palmas-pmic";
 436                         interrupt-parent = <&palmas>;
 437                         interrupts = <14 IRQ_TYPE_NONE>;
 438                         interrupt-name = "short-irq";
 439
 440                         ti,ldo6-vibrator;
 441
 442                         regulators {
 443                                 smps123_reg: smps123 {
 444                                         /* VDD_OPP_MPU */
 445                                         regulator-name = "smps123";
 446                                         regulator-min-microvolt = < 600000>;
 447                                         regulator-max-microvolt = <1500000>;
 448                                         regulator-always-on;
 449                                         regulator-boot-on;
 450                                 };
 451
 452                                 smps45_reg: smps45 {
 453                                         /* VDD_OPP_MM */
 454                                         regulator-name = "smps45";
 455                                         regulator-min-microvolt = < 600000>;
 456                                         regulator-max-microvolt = <1310000>;
 457                                         regulator-always-on;
 458                                         regulator-boot-on;
 459                                 };
 460
 461                                 smps6_reg: smps6 {
 462                                         /* VDD_DDR3 - over VDD_SMPS6 */
 463                                         regulator-name = "smps6";
 464                                         regulator-min-microvolt = <1500000>;
 465                                         regulator-max-microvolt = <1500000>;
 466                                         regulator-always-on;
 467                                         regulator-boot-on;
 468                                 };
 469
 470                                 smps7_reg: smps7 {
 471                                         /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
 472                                         regulator-name = "smps7";
 473                                         regulator-min-microvolt = <1800000>;
 474                                         regulator-max-microvolt = <1800000>;
 475                                         regulator-always-on;
 476                                         regulator-boot-on;
 477                                 };
 478
 479                                 smps8_reg: smps8 {
 480                                         /* VDD_OPP_CORE */
 481                                         regulator-name = "smps8";
 482                                         regulator-min-microvolt = < 600000>;
 483                                         regulator-max-microvolt = <1310000>;
 484                                         regulator-always-on;
 485                                         regulator-boot-on;
 486                                 };
 487
 488                                 smps9_reg: smps9 {
 489                                         /* VDDA_2v1_AUD over VDD_2v1 */
 490                                         regulator-name = "smps9";
 491                                         regulator-min-microvolt = <3300000>;
 492                                         regulator-max-microvolt = <3300000>;
 493                                         ti,smps-range = <0x80>;
 494                                         regulator-always-on;
 495                                         regulator-boot-on;
 496                                 };
 497
 498                                 smps10_out2_reg: smps10_out2 {
 499                                         /* VBUS_5V_OTG */
 500                                         regulator-name = "smps10_out2";
 501                                         regulator-min-microvolt = <5000000>;
 502                                         regulator-max-microvolt = <5000000>;
 503                                         regulator-always-on;
 504                                         regulator-boot-on;
 505                                 };
 506
 507                                 smps10_out1_reg: smps10_out1 {
 508                                         /* VBUS_5V_OTG */
 509                                         regulator-name = "smps10_out1";
 510                                         regulator-min-microvolt = <5000000>;
 511                                         regulator-max-microvolt = <5000000>;
 512                                 };
 513
 514                                 ldo1_reg: ldo1 {
 515                                         /* VDDAPHY_CAM: vdda_csiport */
 516                                         regulator-name = "ldo1";
 517                                         regulator-min-microvolt = <1500000>;
 518                                         regulator-max-microvolt = <1800000>;
 519                                 };
 520
 521                                 ldo2_reg: ldo2 {
 522                                         /* VDD_3V3_WLAN */
 523                                         regulator-name = "ldo2";
 524                                         regulator-min-microvolt = <3300000>;
 525                                         regulator-max-microvolt = <3300000>;
 526                                         startup-delay-us = <1000>;
 527                                 };
 528
 529                                 ldo3_reg: ldo3 {
 530                                         /* VCC_1V5_AUD */
 531                                         regulator-name = "ldo3";
 532                                         regulator-min-microvolt = <1500000>;
 533                                         regulator-max-microvolt = <1500000>;
 534                                         regulator-always-on;
 535                                         regulator-boot-on;
 536                                 };
 537
 538                                 ldo4_reg: ldo4 {
 539                                         /* VDDAPHY_DISP: vdda_dsiport/hdmi */
 540                                         regulator-name = "ldo4";
 541                                         regulator-min-microvolt = <1500000>;
 542                                         regulator-max-microvolt = <1800000>;
 543                                 };
 544
 545                                 ldo5_reg: ldo5 {
 546                                         /* VDDA_1V8_PHY: usb/sata/hdmi.. */
 547                                         regulator-name = "ldo5";
 548                                         regulator-min-microvolt = <1800000>;
 549                                         regulator-max-microvolt = <1800000>;
 550                                         regulator-always-on;
 551                                         regulator-boot-on;
 552                                 };
 553
 554                                 ldo6_reg: ldo6 {
 555                                         /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
 556                                         regulator-name = "ldo6";
 557                                         regulator-min-microvolt = <1200000>;
 558                                         regulator-max-microvolt = <1200000>;
 559                                         regulator-always-on;
 560                                         regulator-boot-on;
 561                                 };
 562
 563                                 ldo7_reg: ldo7 {
 564                                         /* VDD_VPP: vpp1 */
 565                                         regulator-name = "ldo7";
 566                                         regulator-min-microvolt = <2000000>;
 567                                         regulator-max-microvolt = <2000000>;
 568                                         /* Only for efuse reprograming! */
 569                                         status = "disabled";
 570                                 };
 571
 572                                 ldo8_reg: ldo8 {
 573                                         /* VDD_3V_GP: act led/serial console */
 574                                         regulator-name = "ldo8";
 575                                         regulator-min-microvolt = <3000000>;
 576                                         regulator-max-microvolt = <3000000>;
 577                                         regulator-always-on;
 578                                         regulator-boot-on;
 579                                 };
 580
 581                                 ldo9_reg: ldo9 {
 582                                         /* VCC_DV_SDIO: vdds_sdcard */
 583                                         regulator-name = "ldo9";
 584                                         regulator-min-microvolt = <1800000>;
 585                                         regulator-max-microvolt = <3000000>;
 586                                         regulator-boot-on;
 587                                 };
 588
 589                                 ldoln_reg: ldoln {
 590                                         /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
 591                                         regulator-name = "ldoln";
 592                                         regulator-min-microvolt = <1800000>;
 593                                         regulator-max-microvolt = <1800000>;
 594                                         regulator-always-on;
 595                                         regulator-boot-on;
 596                                 };
 597
 598                                 ldousb_reg: ldousb {
 599                                         /* VDDA_3V_USB: VDDA_USBHS33 */
 600                                         regulator-name = "ldousb";
 601                                         regulator-min-microvolt = <3250000>;
 602                                         regulator-max-microvolt = <3250000>;
 603                                         regulator-always-on;
 604                                         regulator-boot-on;
 605                                 };
 606
 607                                 regen3_reg: regen3 {
 608                                         /* REGEN3 controls LDO9 supply to card */
 609                                         regulator-name = "regen3";
 610                                         regulator-always-on;
 611                                         regulator-boot-on;
 612                                 };
 613                         };
 614                 };
 615         };
 616 };
 617
 618 &i2c2 {
 619         pinctrl-names = "default";
 620         pinctrl-0 = <&i2c2_pins>;
 621
 622         clock-frequency = <100000>;
 623 };
 624
 625 &usbhshost {
 626         port2-mode = "ehci-hsic";
 627         port3-mode = "ehci-hsic";
 628 };
 629
 630 &usbhsehci {
 631         phys = <0 &hsusb2_phy &hsusb3_phy>;
 632 };
 633
 634 &usb3 {
 635        extcon = <&extcon_usb3>;
 636        vbus-supply = <&smps10_out1_reg>;
 637 };
 638
 639 &cpu0 {
 640         cpu0-supply = <&smps123_reg>;
 641 };
 642
 643 &dss {
 644         status = "ok";
 645
 646         pinctrl-names = "default";
 647         pinctrl-0 = <&dss_dpi_pins>;
 648
 649         port {
 650                 dpi_dvi_out: endpoint@0 {
 651                         remote-endpoint = <&tfp410_in>;
 652                         data-lines = <24>;
 653                 };
 654
 655                 dpi_lcd_out: endpoint@1 {
 656                         remote-endpoint = <&lcd_in>;
 657                         data-lines = <24>;
 658                 };
 659         };
 660 };
 661
 662 &dsi2 {
 663         status = "ok";
 664         vdd-supply = <&ldo4_reg>;
 665 };
 666
 667 &hdmi {
 668         status = "ok";
 669         vdda-supply = <&ldo4_reg>;
 670
 671         pinctrl-names = "default";
 672         pinctrl-0 = <&dss_hdmi_pins>;
 673
 674         port {
 675                 hdmi_out: endpoint {
 676                         remote-endpoint = <&hdmi_connector_in>;
 677                         lanes = <1 0 3 2 5 4 7 6>;
 678                 };
 679         };
 680 };