1 .\" Copyright (c) 1983, 1991, 1993
2 .\" The Regents of the University of California.
3 .\" Copyright (c) 2010-2011 The FreeBSD Foundation
4 .\" All rights reserved.
6 .\" Portions of this documentation were written at the Centre for Advanced
7 .\" Internet Architectures, Swinburne University of Technology, Melbourne,
8 .\" Australia by David Hayes under sponsorship from the FreeBSD Foundation.
10 .\" Redistribution and use in source and binary forms, with or without
11 .\" modification, are permitted provided that the following conditions
13 .\" 1. Redistributions of source code must retain the above copyright
14 .\" notice, this list of conditions and the following disclaimer.
15 .\" 2. Redistributions in binary form must reproduce the above copyright
16 .\" notice, this list of conditions and the following disclaimer in the
17 .\" documentation and/or other materials provided with the distribution.
18 .\" 3. Neither the name of the University nor the names of its contributors
19 .\" may be used to endorse or promote products derived from this software
20 .\" without specific prior written permission.
22 .\" THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
23 .\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
24 .\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
25 .\" ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
26 .\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
27 .\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
28 .\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
29 .\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
30 .\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
31 .\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
34 .\" From: @(#)tcp.4 8.1 (Berkeley) 6/5/93
42 .Nd Internet Transmission Control Protocol
49 .Fn socket AF_INET SOCK_STREAM 0
53 protocol provides reliable, flow-controlled, two-way
55 It is a byte-stream protocol used to
61 Internet address format and, in addition, provides a per-host
63 .Dq "port addresses" .
64 Thus, each address is composed
65 of an Internet address specifying the host and network,
68 port on the host identifying the peer entity.
76 Active sockets initiate connections to passive
80 sockets are created active; to create a
83 system call must be used
84 after binding the socket with the
87 Only passive sockets may use the
89 call to accept incoming connections.
90 Only active sockets may use the
92 call to initiate connections.
96 their location to match
97 incoming connection requests from multiple networks.
98 This technique, termed
99 .Dq "wildcard addressing" ,
101 server to provide service to clients on multiple networks.
102 To create a socket which listens on all networks, the Internet
108 port may still be specified
109 at this time; if the port is not specified, the system will assign one.
110 Once a connection has been established, the socket's address is
111 fixed by the peer entity's location.
112 The address assigned to the
113 socket is the address associated with the network interface
114 through which packets are being transmitted and received.
115 Normally, this address corresponds to the peer entity's network.
118 supports a number of socket options which can be set with
122 .Bl -tag -width ".Dv TCP_FUNCTION_BLK"
124 Information about a socket's underlying TCP session may be retrieved
125 by passing the read-only option
129 It accepts a single argument: a pointer to an instance of
130 .Vt "struct tcp_info" .
132 This API is subject to change; consult the source to determine
133 which fields are currently filled out by this option.
135 specific additions include
139 bandwidth-controlled window space.
141 Set or query congestion control algorithm specific parameters.
145 .It Dv TCP_CONGESTION
146 Select or query the congestion control algorithm that TCP will use for the
151 .It Dv TCP_FUNCTION_BLK
152 Select or query the set of functions that TCP will use for this connection.
153 This allows a user to select an alternate TCP stack.
154 The alternate TCP stack must already be loaded in the kernel.
155 To list the available TCP stacks, see
156 .Va functions_available
159 section further down.
160 To list the default TCP stack, see
161 .Va functions_default
168 option accepts a per-socket timeout argument of
170 in seconds, for new, non-established
173 For the global default in milliseconds see
177 section further down.
181 option accepts an argument of
183 for the amount of time, in seconds, that the connection must be idle
184 before keepalive probes (if enabled) are sent for the connection of this
186 If set on a listening socket, the value is inherited by the newly created
189 For the global default in milliseconds see
193 section further down.
197 option accepts an argument of
199 to set the per-socket interval, in seconds, between keepalive probes sent
201 If set on a listening socket, the value is inherited by the newly created
204 For the global default in milliseconds see
208 section further down.
212 option accepts an argument of
214 and allows a per-socket tuning of the number of probes sent, with no response,
215 before the connection will be dropped.
216 If set on a listening socket, the value is inherited by the newly created
219 For the global default see the
223 section further down.
225 Under most circumstances,
227 sends data when it is presented;
228 when outstanding data has not yet been acknowledged, it gathers
229 small amounts of output to be sent in a single packet once
230 an acknowledgement is received.
231 For a small number of clients, such as window systems
232 that send a stream of mouse events which receive no replies,
233 this packetization may cause significant delays.
236 defeats this algorithm.
238 By default, a sender- and
239 .No receiver- Ns Tn TCP
240 will negotiate among themselves to determine the maximum segment size
241 to be used for each connection.
244 option allows the user to determine the result of this negotiation,
245 and to reduce it if desired.
248 usually sends a number of options in each packet, corresponding to
251 extensions which are provided in this implementation.
254 is provided to disable
256 option use on a per-connection basis.
259 .No sender- Ns Tn TCP
262 bit, and begin transmission immediately (if permitted) at the end of
267 When this option is set to a non-zero value,
269 will delay sending any data at all until either the socket is closed,
270 or the internal send buffer is filled.
272 This option enables the use of MD5 digests (also known as TCP-MD5)
273 on writes to the specified socket.
274 Outgoing traffic is digested;
275 digests on incoming traffic are verified.
276 When this option is enabled on a socket, all inbound and outgoing
277 TCP segments must be signed with MD5 digests.
279 One common use for this in a
281 router deployment is to enable
282 based routers to interwork with Cisco equipment at peering points.
283 Support for this feature conforms to RFC 2385.
285 In order for this option to function correctly, it is necessary for the
286 administrator to add a tcp-md5 key entry to the system's security
287 associations database (SADB) using the
290 This entry can only be specified on a per-host basis at this time.
292 If an SADB entry cannot be found for the destination,
293 the system does not send any outgoing segments and drops any inbound segments.
295 Manage collection of connection level statistics using the
299 Each dropped segment is taken into account in the TCP protocol statistics.
300 .It Dv TCP_TXTLS_ENABLE
301 Enable in-kernel Transport Layer Security (TLS) for data written to this
306 .It Dv TCP_TXTLS_MODE
307 The integer argument can be used to get or set the current TLS transmit mode
312 .It Dv TCP_RXTLS_ENABLE
313 Enable in-kernel TLS for data read from this socket.
317 .It Dv TCP_REUSPORT_LB_NUMA
318 Changes NUMA affinity filtering for an established TCP listen
320 This option takes a single integer argument which specifies
321 the NUMA domain to filter on for this listen socket.
322 The argument can also have the follwing special values:
323 .Bl -tag -width "Dv TCP_REUSPORT_LB_NUMA"
324 .It Dv TCP_REUSPORT_LB_NUMA_NODOM
325 Remove NUMA filtering for this listen socket.
326 .It Dv TCP_REUSPORT_LB_NUMA_CURDOM
327 Filter traffic associated with the domain where the calling thread is
329 This is typically used after a process or thread inherits a listen
330 socket from its parent, and sets its CPU affinity to a particular core.
334 The option level for the
336 call is the protocol number for
339 .Xr getprotobyname 3 ,
342 All options are declared in
347 transport level may be used with
351 Incoming connection requests that are source-routed are noted,
352 and the reverse source route is used in responding.
354 The default congestion control algorithm for
358 Other congestion control algorithms can be made available using the
364 protocol implements a number of variables in the
369 .Bl -tag -width ".Va TCPCTL_DO_RFC1323"
370 .It Dv TCPCTL_DO_RFC1323
372 Implement the window scaling and timestamp options of RFC 1323
374 .It Dv TCPCTL_MSSDFLT
376 The default value used for the maximum segment size
378 when no advice to the contrary is received from MSS negotiation.
379 .It Dv TCPCTL_SENDSPACE
384 .It Dv TCPCTL_RECVSPACE
390 Log any connection attempts to ports where there is not a socket
391 accepting connections.
392 The value of 1 limits the logging to
394 (connection establishment) packets only.
395 That of 2 results in any
397 packets to closed ports being logged.
398 Any value unlisted above disables the logging
399 (default is 0, i.e., the logging is disabled).
401 The Maximum Segment Lifetime, in milliseconds, for a packet.
403 Timeout, in milliseconds, for new, non-established
406 The default is 75000 msec.
408 Amount of time, in milliseconds, that the connection must be idle
409 before keepalive probes (if enabled) are sent.
410 The default is 7200000 msec (2 hours).
412 The interval, in milliseconds, between keepalive probes sent to remote
413 machines, when no response is received on a
416 The default is 75000 msec.
418 Number of probes sent, with no response, before a connection
420 The default is 8 packets.
421 .It Va always_keepalive
426 connections, the kernel will
427 periodically send a packet to the remote host to verify the connection
432 unreachable messages may abort connections in
438 reassembly queue if the system is low on mbufs.
440 If enabled, disable sending of RST when a connection is attempted
441 to a port where there is not a socket accepting connections.
445 Delay ACK to try and piggyback it onto a data packet.
447 Maximum amount of time, in milliseconds, before a delayed ACK is sent.
448 .It Va path_mtu_discovery
449 Enable Path MTU Discovery.
453 control-block hash table
455 This may be tuned using the kernel option
458 .Va net.inet.tcp.tcbhashsize
462 Number of active process control blocks
465 Determines whether or not
467 cookies should be generated for outbound
471 cookies are a great help during
473 flood attacks, and are enabled by default.
476 .It Va isn_reseed_interval
477 The interval (in seconds) specifying how often the secret data used in
478 RFC 1948 initial sequence number calculations should be reseeded.
479 By default, this variable is set to zero, indicating that
480 no reseeding will occur.
481 Reseeding should not be necessary, and will break
483 recycling for a few minutes.
484 .It Va reass.cursegments
485 The current total number of segments present in all reassembly queues.
486 .It Va reass.maxsegments
487 The maximum limit on the total number of segments across all reassembly
489 The limit can be adjusted as a tunable.
490 .It Va reass.maxqueuelen
491 The maximum number of segments allowed in each reassembly queue.
492 By default, the system chooses a limit based on each TCP connection's
493 receive buffer size and maximum segment size (MSS).
494 The actual limit applied to a session's reassembly queue will be the lower of
495 the system-calculated automatic limit and the user-specified
496 .Va reass.maxqueuelen
498 .It Va rexmit_initial , rexmit_min , rexmit_slop
499 Adjust the retransmit timer calculation for
502 typically added to the raw calculation to take into account
503 occasional variances that the
505 (smoothed round-trip time)
506 is unable to accommodate, while the minimum specifies an
511 second minimum, these RFCs tend to focus on streaming behavior,
512 and fail to deal with the fact that a 1 second minimum has severe
513 detrimental effects over lossy interactive connections, such
514 as a 802.11b wireless link, and over very fast but lossy
515 connections for those cases not covered by the fast retransmit
517 For this reason, we use 200ms of slop and a near-0
518 minimum, which gives us an effective minimum of 200ms (similar to
520 The initial value is used before an RTT measurement has been performed.
521 .It Va initcwnd_segments
522 Enable the ability to specify initial congestion window in number of segments.
523 The default value is 10 as suggested by RFC 6928.
524 Changing the value on fly would not affect connections using congestion window
527 This regulates the burst of packets allowed to be sent in the first RTT.
528 The value should be relative to the link capacity.
529 Start with small values for lower-capacity links.
530 Large bursts can cause buffer overruns and packet drops if routers have small
531 buffers or the link is experiencing congestion.
533 Enable the New Congestion Window Validation mechanism as described in RFC 7661.
534 This gently reduces the congestion window during periods, where TCP is
535 application limited and the network bandwidth is not utilized completely.
536 That prevents self-inflicted packet losses once the application starts to
537 transmit data at a higher speed.
539 Calculate the bytes in flight using the algorithm described in RFC 6675, and
540 is also a prerequisite to enable Proportional Rate Reduction.
542 Enable the Limited Transmit algorithm as described in RFC 3042.
543 It helps avoid timeouts on lossy links and also when the congestion window
544 is small, as happens on short transfers.
546 Enable support for RFC 3390, which allows for a variable-sized
547 starting congestion window on new connections, depending on the
548 maximum segment size.
549 This helps throughput in general, but
550 particularly affects short transfers and high-bandwidth large
551 propagation-delay connections.
553 Enable support for RFC 2018, TCP Selective Acknowledgment option,
554 which allows the receiver to inform the sender about all successfully
555 arrived segments, allowing the sender to retransmit the missing segments
558 Maximum number of SACK holes per connection.
560 .It Va sack.globalmaxholes
561 Maximum number of SACK holes per system, across all connections.
564 When a TCP connection enters the
566 state, its associated socket structure is freed, since it is of
567 negligible size and use, and a new structure is allocated to contain a
568 minimal amount of information necessary for sustaining a connection in
569 this state, called the compressed TCP TIME_WAIT state.
570 Since this structure is smaller than a socket structure, it can save
571 a significant amount of system memory.
573 .Va net.inet.tcp.maxtcptw
574 MIB variable controls the maximum number of these structures allocated.
575 By default, it is initialized to
576 .Va kern.ipc.maxsockets
578 .It Va nolocaltimewait
579 Suppress creating of compressed TCP TIME_WAIT states for connections in
580 which both endpoints are local.
581 .It Va fast_finwait2_recycle
585 connections faster when the socket is marked as
587 (no user process has the socket open, data received on
588 the socket cannot be read).
589 The timeout used here is
590 .Va finwait2_timeout .
591 .It Va finwait2_timeout
592 Timeout to use for fast recycling of
596 Defaults to 60 seconds.
598 Enable support for TCP Explicit Congestion Notification (ECN).
599 ECN allows a TCP sender to reduce the transmission rate in order to
606 Allow incoming connections to request ECN.
607 Outgoing connections will request ECN.
609 Allow incoming connections to request ECN.
610 Outgoing connections will not request ECN.
612 .It Va ecn.maxretries
613 Number of retries (SYN or SYN/ACK retransmits) before disabling ECN on a
615 This is needed to help with connection establishment
616 when a broken firewall is in the network path.
617 .It Va pmtud_blackhole_detection
618 Enable automatic path MTU blackhole detection.
619 In case of retransmits of MSS sized segments,
620 the OS will lower the MSS to check if it's an MTU problem.
621 If the current MSS is greater than the configured value to try
622 .Po Va net.inet.tcp.pmtud_blackhole_mss
624 .Va net.inet.tcp.v6pmtud_blackhole_mss
626 it will be set to this value, otherwise,
627 the MSS will be set to the default values
628 .Po Va net.inet.tcp.mssdflt
630 .Va net.inet.tcp.v6mssdflt
635 Disable path MTU blackhole detection.
637 Enable path MTU blackhole detection for IPv4 and IPv6.
639 Enable path MTU blackhole detection only for IPv4.
641 Enable path MTU blackhole detection only for IPv6.
643 .It Va pmtud_blackhole_mss
644 MSS to try for IPv4 if PMTU blackhole detection is turned on.
645 .It Va v6pmtud_blackhole_mss
646 MSS to try for IPv6 if PMTU blackhole detection is turned on.
647 .It Va functions_available
648 List of available TCP function blocks (TCP stacks).
649 .It Va functions_default
650 The default TCP function block (TCP stack).
651 .It Va functions_inherit_listen_socket_stack
652 Determines whether to inherit listen socket's tcp stack or use the current
653 system default tcp stack, as defined by
654 .Va functions_default .
657 Use criteria defined in RFC793 instead of RFC5961 for accepting RST segments.
660 Use criteria defined in RFC793 instead of RFC5961 for accepting SYN segments.
662 .It Va ts_offset_per_conn
663 When initializing the TCP timestamps, use a per connection offset instead of a
664 per host pair offset.
665 Default is to use per connection offsets as recommended in RFC 7323.
666 .It Va perconn_stats_enable
667 Controls the default collection of statistics for all connections using the
670 0 disables, 1 enables, 2 enables random sampling across log id connection
671 groups with all connections in a group receiving the same setting.
672 .It Va perconn_stats_sample_rates
673 A CSV list of template_spec=percent key-value pairs which controls the per
674 template sampling rates when
679 A socket operation may fail with one of the following errors returned:
682 when trying to establish a connection on a socket which
684 .It Bo Er ENOBUFS Bc or Bo Er ENOMEM Bc
685 when the system runs out of memory for
686 an internal data structure;
688 when a connection was dropped
689 due to excessive retransmissions;
692 forces the connection to be closed;
693 .It Bq Er ECONNREFUSED
695 peer actively refuses connection establishment (usually because
696 no process is listening to the port);
699 is made to create a socket with a port which has already been
701 .It Bq Er EADDRNOTAVAIL
702 when an attempt is made to create a
703 socket with a network address for which no network interface
705 .It Bq Er EAFNOSUPPORT
706 when an attempt is made to bind or connect a socket to a multicast
709 when trying to change TCP function blocks at an invalid point in the session;
711 when trying to use a TCP function block that is not available;
733 .%T "TCP Extensions for High Performance"
738 .%T "Protection of BGP Sessions via the TCP MD5 Signature Option"
742 .%A "K. Ramakrishnan"
745 .%T "The Addition of Explicit Congestion Notification (ECN) to IP"
753 The RFC 1323 extensions for window scaling and timestamps were added
758 option was introduced in
761 .Em subject to change .