sys/gnu/dts/arm/socfpga_arria10_socdk.dtsi

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * Copyright (C) 2015 Altera Corporation <www.altera.com>
   4  */
   5 #include "socfpga_arria10.dtsi"
   6
   7 / {
   8         model = "Altera SOCFPGA Arria 10";
   9         compatible = "altr,socfpga-arria10", "altr,socfpga";
  10
  11         aliases {
  12                 ethernet0 = &gmac0;
  13                 serial0 = &uart1;
  14         };
  15
  16         chosen {
  17                 bootargs = "earlyprintk";
  18                 stdout-path = "serial0:115200n8";
  19         };
  20
  21         memory@0 {
  22                 name = "memory";
  23                 device_type = "memory";
  24                 reg = <0x0 0x40000000>; /* 1GB */
  25         };
  26
  27         a10leds {
  28                 compatible = "gpio-leds";
  29
  30                 a10sr_led0 {
  31                         label = "a10sr-led0";
  32                         gpios = <&a10sr_gpio 0 1>;
  33                 };
  34
  35                 a10sr_led1 {
  36                         label = "a10sr-led1";
  37                         gpios = <&a10sr_gpio 1 1>;
  38                 };
  39
  40                 a10sr_led2 {
  41                         label = "a10sr-led2";
  42                         gpios = <&a10sr_gpio 2 1>;
  43                 };
  44
  45                 a10sr_led3 {
  46                         label = "a10sr-led3";
  47                         gpios = <&a10sr_gpio 3 1>;
  48                 };
  49         };
  50
  51         ref_033v: 033-v-ref {
  52                 compatible = "regulator-fixed";
  53                 regulator-name = "0.33V";
  54                 regulator-min-microvolt = <330000>;
  55                 regulator-max-microvolt = <330000>;
  56         };
  57
  58         soc {
  59                 clkmgr@ffd04000 {
  60                         clocks {
  61                                 osc1 {
  62                                         clock-frequency = <25000000>;
  63                                 };
  64                         };
  65                 };
  66         };
  67 };
  68
  69 &gmac0 {
  70         phy-mode = "rgmii";
  71         phy-addr = <0xffffffff>; /* probe for phy addr */
  72
  73         /*
  74          * These skews assume the user's FPGA design is adding 600ps of delay
  75          * for TX_CLK on Arria 10.
  76          *
  77          * All skews are offset since hardware skew values for the ksz9031
  78          * range from a negative skew to a positive skew.
  79          * See the micrel-ksz90x1.txt Documentation file for details.
  80          */
  81         txd0-skew-ps = <0>; /* -420ps */
  82         txd1-skew-ps = <0>; /* -420ps */
  83         txd2-skew-ps = <0>; /* -420ps */
  84         txd3-skew-ps = <0>; /* -420ps */
  85         rxd0-skew-ps = <420>; /* 0ps */
  86         rxd1-skew-ps = <420>; /* 0ps */
  87         rxd2-skew-ps = <420>; /* 0ps */
  88         rxd3-skew-ps = <420>; /* 0ps */
  89         txen-skew-ps = <0>; /* -420ps */
  90         txc-skew-ps = <1860>; /* 960ps */
  91         rxdv-skew-ps = <420>; /* 0ps */
  92         rxc-skew-ps = <1680>; /* 780ps */
  93         max-frame-size = <3800>;
  94         status = "okay";
  95 };
  96
  97 &gpio1 {
  98         status = "okay";
  99 };
 100
 101 &spi1 {
 102         status = "okay";
 103
 104         resource-manager@0 {
 105                 compatible = "altr,a10sr";
 106                 reg = <0>;
 107                 spi-max-frequency = <100000>;
 108                 /* low-level active IRQ at GPIO1_5 */
 109                 interrupt-parent = <&portb>;
 110                 interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
 111                 interrupt-controller;
 112                 #interrupt-cells = <2>;
 113
 114                 a10sr_gpio: gpio-controller {
 115                         compatible = "altr,a10sr-gpio";
 116                         gpio-controller;
 117                         #gpio-cells = <2>;
 118                 };
 119
 120                 a10sr_rst: reset-controller {
 121                         compatible = "altr,a10sr-reset";
 122                         #reset-cells = <1>;
 123                 };
 124         };
 125 };
 126
 127 &i2c1 {
 128         status = "okay";
 129
 130         /*
 131          * adjust the falling times to decrease the i2c frequency to 50Khz
 132          * because the LCD module does not work at the standard 100Khz
 133          */
 134         clock-frequency = <100000>;
 135         i2c-sda-falling-time-ns = <6000>;
 136         i2c-scl-falling-time-ns = <6000>;
 137
 138         adc@14 {
 139                 compatible = "lltc,ltc2497";
 140                 reg = <0x14>;
 141                 vref-supply = <&ref_033v>;
 142         };
 143
 144         adc@16 {
 145                 compatible = "lltc,ltc2497";
 146                 reg = <0x16>;
 147                 vref-supply = <&ref_033v>;
 148         };
 149
 150         eeprom@51 {
 151                 compatible = "atmel,24c32";
 152                 reg = <0x51>;
 153                 pagesize = <32>;
 154         };
 155
 156         rtc@68 {
 157                 compatible = "dallas,ds1339";
 158                 reg = <0x68>;
 159         };
 160
 161         ltc@5c {
 162                 compatible = "ltc2977";
 163                 reg = <0x5c>;
 164         };
 165 };
 166
 167 &uart1 {
 168         status = "okay";
 169 };
 170
 171 &usb0 {
 172         status = "okay";
 173         disable-over-current;
 174 };
 175
 176 &watchdog1 {
 177         status = "okay";
 178 };